NSVS1097 Jan. 2005
Application
243.95MHz PHS Base-Station 1st IF
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Table 1. Elect r ical Specifications Spec. Typ.
243.95MHz -
±130kHz -
4.0dB 3.3dB
0.85dB 0.40dB
0.85us 0.40us
--
Attenuation f0± 600kHz 25dB 30dB
f0±10.7MHz 50dB 65dB
f0±21.4MHz 60dB 65dB
(Operat ing Temperature Range : -30〜+85℃)
Item
Nominal Center Fr equency (f0)
3dB Band Width
Insertion Loss at f0
Ripple f0±100kHz
Group Delay Time Ripple f0±100kHz
Maximum Rating: (Table 2)
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.5x3.5x1.0[mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
Table 2. Maximum Ratings
Item Rating
Maximum Input Power +5dBm
Operating Temperature Range -30~+85ºC
Storage Temperature -40~+95ºC
JRC SAW FILTER
NSVS1097
Communications Equipment Division
Communications Equipment Marketing Department
10-1, Nishi-Shinjuku 6-chome, Shinjuku-ku,
Tokyo, 160-8328 Japan
Tel. +81 3-3348-3845
Fax. +81 3-3348-3935
http://www.jrc.co.jp/jp/product/device/saw/index.html (Jap ane se)
http://www.jrc.co.jp/eng/product/saw/index.html (English)
NSVS1097 Jan. 2005
Pin no. Connection
1 GND
2 IN/OUT
3 GND
4 GND
5 GND
6 OUT/IN
7 GND
8 GND
3.5±0.2
3.5 0.2
1.0 0.2
(0.95) (0.8)
[5x]
(2.54)
(1.27)
(0.6)
[8x]
(0.6)
2
34
5
6
7
8
1
(1.0)
(2)
(1)
(c)
(b)
(a)
[2x]
±
±
0.8
4.3 0.8
[6x]
1.3
[6x]
1.27
4.3
Via-Hole(φ
0.3)
1.27
1
2
3 4 5
6
7
8
IN
50Ω
OUT
Ω
Fig.1 Measuring circuit
50
SAW
511
S7
Fig.3 Desirable land area (in mm)
Marking
(1) Lot Number
(a) Year
(b) Month
Oct. --- X
Nov. --- Y
Dec. --- Z
(c) Date
0 - 90
10 - 19 1
20 - 31 2
(2) Part number Mark
Fig.2 Package Dimensions (in mm)
NSVS1097 Jan. 2005
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than –30ºC or more than +85ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of
soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power
of soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature
of this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity
to this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
2. The information contained herein may be changed without prior notice. It is
therefore advisable to contact Japan Radio Company before proceeding with
the design of equipment incorporating this product.
3.The products are designed to be used with ordinary electronic equipment (data
and communications equipment, office equipment, audio-video equipment,
measuring instruments, etc). Japan Radio Company does not assume any
liability for the case using the products with the application required high
reliability or safety extremely (such as space equipment, sea-bottom
equipment, medical equipment etc). When intending to use any our product
please contact our sales representatives in advance.
NSVS1097 Jan. 2005
1
2
3 4 5
6
7
8
IN50ΩOUT
Fig. 4
SAW
LQW18ANR10G00D
100nH
Ω
50
TZY2Z2R5A001B00
0.65-2.5pF
TZY2Z2R5A001B00
0.65-2.5pF
TZY2Z2R5A001B00
0.65-2.5pF
TZY2Z2R5A001B00
0.65-2.5pF
LQW18ANR10G00D
100nH
