Features
• HCMOS/LSTTL/TTL performance compatible
• 1000 V/µs minimum Common Mode Rejection (CMR)
at VCM = 50 V (HCPL-261A family) and 15 kV/µs
minimum CMR at VCM = 1000 V (HCPL-261N family)
• High speed: 10 MBd typical
• AC and DC performance specied over industrial
temperature range -40°C to +85°C
• Available in 8 pin DIP, SOIC-8 packages
• Safety approval:
– UL recognized per UL1577 3750 V rms for 1 minute
and 5000 V rms for 1 minute (Option 020)
– CSA Approved
– IEC/EN/DIN EN 60747-5-2 approved
Applications
• Low input current (3.0 mA) HCMOS compatible
version of 6N137 optocoupler
• Isolated line receiver
• Simplex/multiplex data transmission
• Computer-peripheral interface
• Digital isolation for A/D, D/A conversion
• Switching power supplies
• Instrumentation input/output isolation
• Ground loop elimination
• Pulse transformer replacement
HCPL-261A, HCPL-061A, HCPL-263A, HCPL-063A
HCPL-261N, HCPL-061N, HCPL-263N, HCPL-063N
HCMOS Compatible, High CMR, 10 MBd Optocouplers
Data Sheet
The connection of a 0.1 µF bypass capacitor between pins 5 and 8 is
required.
1
2
3
4
8
7
6
5
CATHODE
ANODE
GND
V
VCC
O
HCPL-261A Functional Diagram
1
2
3
4
8
7
6
5
ANODE 2
CATHODE 2
CATHODE 1
ANODE 1
GND
V
VCC
O2
VEVO1
HCPL-261A/261N
HCPL-061A/061N
HCPL-263A/263N
HCPL-063A/063N
NC
NC SHIELD SHIELD
LED
ON
OFF
ON
OFF
ON
OFF
ENABLE
H
H
L
L
NC
NC
OUTPUT
L
H
H
H
L
H
TRUTH TABLE
(POSITIVE LOGIC)
LED
ON
OFF
OUTPUT
L
H
TRUTH TABLE
(POSITIVE LOGIC)
Description
The HCPL-261A family of optically coupled gates shown
on this data sheet provide all the benets of the in-
dustry standard 6N137 family with the added benet
of HCMOS compatible input current. This allows direct
interface to all common circuit topologies without ad-
ditional LED buer or drive components. The AlGaAs
LED used allows lower drive currents and reduces
degradation by using the latest LED technology. On
the single channel parts, an enable output allows the de-
tector to be strobed. The output of the detector IC is an
open collector schottky-clamped transistor. The internal
shield provides a minimum common mode transient im-
munity of 1000 V/µs for the HCPL-261A family and 15000
V/µs for the HCPL-261N family.
Functional Diagram
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
2
Selection Guide
Widebody
Minimum CMR 8-Pin DIP (300 Mil) Small-Outline SO-8 (400 Mil) Hermetic
On- Single Dual Single Dual Single Single and
dV/dt VCM Current Output Channel Channel Channel Channel Channel Dual Channel
(V/µs) (V) (mA) Enable Package Package Package Package Package Packages
NA NA 5 YES 6N137[1] HCPL-0600[1] HCNW137[1]
NO HCPL-2630[1] HCPL-0630[1]
5,000 50 YES HCPL-2601[1] HCPL-0601[1] HCNW2601[1]
NO HCPL-2631[1] HCPL-0631[1]
10,000 1,000 YES HCPL-2611[1] HCPL-0611[1] HCNW2611[1]
NO HCPL-4661[1] HCPL-0661[1]
1,000 50 YES HCPL-2602[1]
3,500 300 YES HCPL-2612[1]
1,000 50 3 YES HCPL-261A HCPL-061A
NO HCPL-263A HCPL-063A
1,000[2] 1,000 YES HCPL-261N HCPL-061N
NO HCPL-263N HCPL-063N
1,000 50 12.5 [3] HCPL-193X[1]
HCPL-56XX[1]
HCPL-66XX[1]
Notes:
1. Technical data are on separate Avago publications.
2. 15 kV/µs with VCM = 1 kV can be achieved using Avago application circuit.
3. Enable is available for single channel products only, except for HCPL-193X devices.
Input
Schematic
SHIELD
8
6
5
2+
3
HCPL-261A Schematic a
V
F
USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED
BETWEEN PINS 5 AND 8 IS RECOMMENDED (SEE NOTE 16).
–
I
F
I
CC
V
CC
V
O
GND
I
O
V
E
I
E
7
HCPL-261A/261N
HCPL-061A/061N
SHIELD
8
7
+
2
HCPL-261A Schematic b
V
F1
–
I
F1
I
CC
V
CC
V
O1
I
O1
1
SHIELD
6
5
–
4
V
F2
+
I
F2
V
O2
GND
I
O2
3
HCPL-263A/263N
HCPL-063A/063N
3
Ordering Information
HCPL-xxxx is UL Recognized with 3750 Vrms for 1 minute per UL1577.
Part number
Option
Package
Surface
Mount
Gull
Wing
Tape
& Reel
UL 5000
Vrms/1
Minute rating
IEC/EN/DIN EN
60747-5-2 Quantity
RoHS
Compliant
Non RoHS
Compliant
HCPL-261A
-000E No option
300mil
DIP-8
50 per tube
-300E #300 X X 50 per tube
-500E #500 X X X 1000 per reel
-020E #020 X 50 per tube
-320E -320 X X X 50 per tube
-520E -520 X X X X 1000 per reel
-060E #060 X 50 per tube
-560E #560 X X X X 1000 per reel
HCPL-261N
-000E No option
300mil
DIP-8
50 per tube
-300E #300 X X 50 per tube
-500E #500 X X X 1000 per reel
-020E #020 X 50 per tube
-320E #320 X X X 50 per tube
-520E -520 X X X X 1000 per reel
-060E #060 X 50 per tube
-360E #360 X X X 50 per tube
-560E - X X X X 1000 per reel
HCPL-263A
-000E No option
300mil
DIP-8
50 per tube
-300E #300 X X 50 per tube
-500E #500 X X X 1000 per reel
-020E #020 X 50 per tube
-320E #320 X X X 50 per tube
-520E -520 X X X X 1000 per reel
HCPL-263N
-000E No option
300mil
DIP-8
50 per tube
-300E #300 X X 50 per tube
-500E #500 X X X 1000 per reel
-020E #020 X 50 per tube
-320E #320 X X X 50 per tube
-520E #520 X X X X 1000 per reel
HCPL-061A
HCPL-061N
-000E No option
SO-8
X 100 per tube
-500E #500 X X 1500 per reel
-060E #060 X X 100 per tube
-560E #560 X X X 1500 per reel
HCPL-063A
HCPL-063N
-000E No option SO-8 X 100 per tube
-500E #500 X X 1500 per reel
To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry. Combination of Option 020 and Option 060 is not available.
Example 1:
HCPL-261A-560E to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packaging
with IEC/EN/DIN EN 60747-5-2 Safety Approval in RoHS compliant.
Example 2:
HCPL-263N to order product of 300mil DIP package in tube packaging and non RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since 15th July 2001 and
RoHS compliant option will use ‘-XXXE‘.
4
HCPL-261A/261N/263A/263N Outline Drawing
Pin Location (for reference only)
Figure 2. Gull wing surface mount option #300.
Figure 1. 8-Pin dual in-line package device outline drawing.
9.40 (0.370)
9.90 (0.390)
PIN ONE
1.78 (0.070) MAX.
A XXXXZ
YYWW
OPTION CODE*
DATE CODE
0.76 (0.030)
1.40 (0.056)
2.28 (0.090)
2.80 (0.110)
0.51 (0.020) MIN.
0.65 (0.025) MAX.
4.70 (0.185) MAX.
2.92 (0.115) MIN.
6.10 (0.240)
6.60 (0.260)
0.20 (0.008)
0.33 (0.013)
5 TYP.
7.36 (0.290)
7.88 (0.310)
DIMENSIONS IN MILLIMETERS AND (INCHES).
5678
4321
1.19 (0.047) MAX.
TYPE NUMBER
* MARKING CODE LETTER FOR OPTION NUMBERS.
"L" = OPTION 020
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
3.56 ± 0.13
(0.140 ± 0.005)
0.635 ± 0.25
(0.025 ± 0.010) 12 NOM.
9.65 ± 0.25
(0.380 ± 0.010)
0.635 ± 0.130
(0.025 ± 0.005)
7.62 ± 0.25
(0.300 ± 0.010)
5
6
7
8
4
3
2
1
9.65 ± 0.25
(0.380 ± 0.010)
6.350 ± 0.25
(0.250 ± 0.010)
1.02 (0.040)
1.27 (0.050)
10.9 (0.430)
2.0 (0.080)
LAND PATTERN RECOMMENDATION
1.080 ± 0.320
(0.043 ± 0.013)
3.56 ± 0.13
(0.140 ± 0.005)
1.780
(0.070)
MAX.
1.19
(0.047)
MAX.
2.540
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
TOLERANCES (UNLESS OTHERWISE SPECIFIED):
LEAD COPLANARITY
MAXIMUM: 0.102 (0.004)
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
xx.xx = 0.01
xx.xxx = 0.005
0.20 (0.008)
0.33 (0.013)
5
HCPL-061A/061N/063A/063N Outline Drawing
Figure 3. 8-Pin Small Outline Package Device Drawing.
Regulatory Information
The HCPL-261A and HCPL-261N
families have been approved by the
following organizations:
UL
Recognized under UL 1577, Com-
ponent Recognition Program, File
E55361.
CSA
Approved under CSA Component
Acceptance Notice #5, File CA
88324.
IEC/EN/DIN EN 60747-5-2
Approved under:
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884
Teil 2):2003-01.
(Option 060 only)
XXX
YWW
8765
4321
5.994 ± 0.203
(0.236 ± 0.008)
3.937 ± 0.127
(0.155 ± 0.005)
0.406 ± 0.076
(0.016 ± 0.003) 1.270
(0.050)BSC
* 5.080 ± 0.127
(0.200 ± 0.005)
3.175 ± 0.127
(0.125 ± 0.005) 1.524
(0.060)
45 X 0.432
(0.017)
0.228 ± 0.025
(0.009 ± 0.001)
TYPE NUMBER
(LAST 3 DIGITS)
DATE CODE
0.305
(0.012)MIN.
* TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)
5.207 ± 0.254 (0.205 ± 0.010)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.
0.203 ± 0.102
(0.008 ± 0.004)
7
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
7.49 (0.295)
1.9 (0.075)
0.64 (0.025)
LAND PATTERN RECOMMENDATION
Solder Reow Thermal Prole
Recommended Pb-Free IR Prole
0
TIME (SECONDS)
TEMPERATURE (
°
C)
200
100
50 150100 200 250
300
0
30
SEC.
50 SEC.
30
SEC.
160°C
140°C
150°C
PEAK
TEMP.
245°C
PEAK
TEMP.
240°CPEAK
TEMP.
230°C
SOLDERING
TIME
200°C
PREHEATING TIME
150°C, 90 + 30 SEC.
2.5 C ± 0.5°C/SEC.
3°C + 1°C/–0.5°C
TIGHT
TYPICAL
LOOSE
ROOM
TEMPERATURE
PREHEATING RATE 3°C + 1°C/–0.5°C/SEC.
REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC.
Note: Non-halide ux should be used.
Note: Non-halide ux should be used.
6
Insulation and Safety Related Specications
8-Pin DIP
(300 Mil) SO-8
Parameter Symbol Value Value Units Conditions
Minimum External Air L(101) 7.1 4.9 mm Measured from input terminals to
Gap (External output terminals, shortest distance
Clearance) through air.
Minimum External L(102) 7.4 4.8 mm Measured from input terminals to
Tracking (External output terminals, shortest distance
Creepage) path along body.
Minimum Internal Plastic 0.08 0.08 mm Through insulation distance, conductor
Gap (Internal Clearance) to conductor, usually the direct
distance between the photoemitter and
photodetector inside the optocoupler
cavity.
Tracking Resistance CTI 200 200 Volts DIN IEC 112/ VDE 0303 Part 1
(Comparative Tracking
Index)
Isolation Group IIIa IIIa Material Group (DIN VDE 0110, 1/89,
Table 1)
Option 300 – surface mount classication is Class A in accordance with CECC 00802.
IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics
Description Symbol PDIP Option 060 SO-8 Option 60 Units
Installation classication per DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤ 150 V rms I-IV
for rated mains voltage ≤ 300 V rms I-IV I-III
for rated mains voltage ≤ 600 V rms I-III I-II
Climatic Classication 55/85/21 55/85/21
Pollution Degree (DIN VDE 0110/1.89) 2 2
Maximum Working Insulation Voltage VIORM 630 566 Vpeak
Input to Output Test Voltage, Method b*
VIORM x 1.875 = VPR, 100% Production Test VPR 1181 1063 Vpeak
with tm = 1 sec, Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
VIORM x 1.5 = VPR, Type and Sample Test, VPR 945 849 Vpeak
tm = 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage* VIOTM 6000 4000 Vpeak
(Transient Overvoltage, tini = 10 sec)
Safety Limiting Values
(See below for Thermal Derating Curve Figures)
Case Temperature TS 175 150 ˚C
Input Current IS,INPUT 230 150 mA
Output Power PS,OUTPUT 600 600 mW
Insulation Resistance at TS, VIO = 500 V RS ≥ 109 ≥ 109 Ω
*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a
detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.
7
Absolute Maximum Ratings
Parameter Symbol Min. Max. Units Note
Storage Temperature TS -55 125 °C
Operating Temperature TA -40 +85 °C
Average Input Current IF(AVG) 10 mA 1
Reverse Input Voltage VR 3 Volts
Supply Voltage VCC -0.5 7 Volts 2
Enable Input Voltage VE -0.5 5.5 Volts
Output Collector Current (Each Channel) IO 50 mA
Output Power Dissipation (Each Channel) PO 60 mW 3
Output Voltage (Each channel) VO -0.5 7 Volts
Lead Solder Temperature
260°C for 10 s, 1.6 mm Below Seating Plane
(Through Hole Parts Only)
Solder Reow Temperature Prole See Package Outline Drawings section
(Surface Mount Parts Only)
Recommended Operating Conditions
Parameter Symbol Min. Max. Units
Input Voltage, Low Level VFL -3 0.8 V
Input Current, High Level IFH 3.0 10 mA
Power Supply Voltage VCC 4.5 5.5 Volts
High Level Enable Voltage VEH 2.0 VCC Volts
Low Level Enable Voltage VEL 0 0.8 Volts
Fan Out (at RL = 1 kΩ) N 5 TTL Loads
Output Pull-up Resistor RL 330 4k Ω
Operating Temperature TA -40 85 °C
8
Electrical Specications
Over recommended operating temperature (TA = -40°C to +85°C) unless otherwise specied.
Parameter Symbol Min. Typ.* Max. Units Test Conditions Fig. Note
High Level Output IOH 3.1 100 µA VCC = 5.5 V, VO = 5.5 V, 4 18
Current VF = 0.8 V, VE = 2.0 V
Low Level Output VOL 0.4 0.6 V VCC = 5.5 V, IOL = 13 mA 5, 8 4, 18
Voltage (sinking), IF = 3.0 mA,
VE = 2.0 V
High Level Supply ICCH 7 10 mA VE = 0.5 V** VCC = 5.5 V 4
9 15 Dual Channel
Products***
Low Level Supply ICCL 8 13 mA VE = 0.5 V** VCC = 5.5 V
12 21 Dual Channel
Products***
High Level Enable IEH -0.6 -1.6 mA VCC = 5.5 V, VE = 2.0 V
Current**
Low Level Enable IEL -0.9 -1.6 mA VCC = 5.5 V, VE = 0.5 V
Current**
Input Forward VF 1.0 1.3 1.6 V IF = 4 mA 6 4
Voltage
Temperature Co- ∆VF/∆TA -1.25 mV/°C IF = 4 mA 4
ecient of Forward
Voltage
Input Reverse BVR 3 5 V IR = 100 µA 4
Breakdown Voltage
Input Capacitance CIN 60 pF f = 1 MHz, VF = 0 V
*All typical values at TA = 25°C, VCC = 5 V
**Single Channel Products only (HCPL-261A/261N/061A/061N)
***Dual Channel Products only (HCPL-263A/263N/063A/063N)
IF = 0 mA
IF = 3.0 mA
Current
Current
9
Switching Specications
Over recommended operating temperature (TA = -40°C to +85°C) unless otherwise specied.
Parameter Symbol Min. Typ.* Max. Units Test Conditions Fig. Note
Input Current Threshold ITHL 1.5 3.0 mA VCC = 5.5 V, VO = 0.6 V, 7, 10 18
High to Low IO >13 mA (Sinking)
Propagation Delay tPLH 52 100 ns IF = 3.5 mA 9, 11, 4, 9,
Time to High Output VCC = 5.0 V, 12 18
Level VE = Open,
Propagation Delay tPHL 53 100 ns 9, 11, 4, 10,
Time to Low Output 12 18
Level
Pulse Width Distortion PWD 11 45 ns 9, 13 17, 18
|tPHL - tPLH|
Propagation Delay Skew tPSK 60 ns 24 11, 18
Output Rise Time tR 42 ns 9, 14 4, 18
Output Fall Time tF 12 ns 9, 14 4, 18
Propagation Delay tEHL 19 ns IF = 3.5 mA 15, 12
Time of Enable VCC = 5.0 V, 16
from VEH to VEL VEL = 0 V, VEH = 3 V,
Propagation Delay tELH 30 ns 15, 12
Time of Enable 16
from VEL to VEH
*All typical values at TA = 25°C, VCC = 5 V.
CL = 15 pF,
RL = 350 Ω
CL = 15 pF,
RL = 350 Ω
Common Mode Transient Immunity Specications, All values at TA = 25°C
Parameter Device Symbol Min. Typ. Max. Units Test Conditions Fig. Note
Output High HCPL-261A |CMH| 1 5 kV/µs VCM = 50 V VCC = 5.0 V, 17 4, 13,
Level Common HCPL-061A RL = 350 Ω, 15, 18
Mode Transient HCPL-263A IF = 0 mA,
Immunity HCPL-063A TA = 25°C
HCPL-261N 1 5 kV/µs VCM = 1000 V
HCPL-061N
HCPL-263N 15 25 kV/µs Using Avago 20 4, 13,
HCPL-063N App Circuit 15
Output Low HCPL-261A |CML| 1 5 kV/µs VCM = 50 V VCC = 5.0 V, 17 4, 14,
Level Common HCPL-061A RL = 350 Ω, 15, 18
Mode Transient HCPL-263A IF = 3.5 mA,
Immunity HCPL-063A VO(MAX) = 0.8 V
HCPL-261N 1 5 kV/µs VCM = 1000 V
HCPL-061N
HCPL-263N 15 25 kV/µs Using Avago 20 4, 14,
HCPL-063N App Circuit 15
VO(MIN) = 2 V
TA = 25°C
10
Notes:
1. Peaking circuits may be used which produce transient input currents up to 30 mA, 50 ns maximum pulse width, provided the average current
does not exceed 10 mA.
2. 1 minute maximum.
3. Derate linearly above 80°C free-air temperature at a rate of 2.7 mW/°C for the SOIC-8 package.
4. Each channel.
5. Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
6. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 VRMS for 1 second (leakage detec-
tion current limit, II-O ≤ 5 µA). This test is performed before the 100% production test for partial discharge (method b) shown in the
IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable.
7. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 VRMS for 1 second (leakage detec-
tion current limit, II-O ≤ 5 µA).
8. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together.
9. The tPLH propagation delay is measured from the 1.75 mA point on the falling edge of the input pulse to the 1.5 V point on the rising edge of
the output pulse.
10. The tPHL propagation delay is measured from the 1.75 mA point on the rising edge of the input pulse to the 1.5 V point on the falling edge of
the output pulse.
11. Propagation delay skew (tPSK) is equal to the worst case dierence in tPLH and/or tPHL that will be seen between any two units under the same
test conditions and operating temperature.
12. Single channel products only (HCPL-261A/261N/061A/061N).
13. Common mode transient immunity in a Logic High level is the maximum tolerable |dVCM/dt| of the common mode pulse, VCM, to assure that
the output will remain in a Logic High state (i.e., Vo > 2.0 V).
14. Common mode transient immunity in a Logic Low level is the maximum tolerable |dVCM/dt| of the common mode pulse, VCM, to assure that
the output will remain in a Logic Low state (i.e., VO < 0.8 V).
15. For sinusoidal voltages
(|dVCM/dt|)max = πfCM VCM(P-P).
16. Bypassing of the power supply line is required with a 0.1 µF ceramic disc capacitor adjacent to each optocoupler as shown in Figure 19. Total
lead length between both ends of the capacitor and the isolator pins should not exceed 10 mm.
17. Pulse Width Distortion (PWD) is dened as the dierence between tPLH and tPHL for any given device.
18. No external pull up is required for a high logic state on the enable input of a single channel product. If the VE pin is not used, tying VE to VCC
will result in improved CMR performance.
19. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. For dual channel parts only.
Package Characteristics
All Typicals at TA = 25°C
Parameter Sym. Package* Min. Typ. Max. Units Test Conditions Fig. Note
Input-Output VISO 3750 V rms RH ≤ 50%, 5, 6
Momentary With- t = 1 min.,
stand Voltage** TA = 25°C
Input-Output RI-O 1012 Ω VI-O = 500 Vdc 4, 8
Resistance
Input-Output CI-O 0.6 pF f = 1 MHz, 4, 8
Capacitance TA = 25°C
Input-Input II-I Dual Channel 0.005 µA RH ≤ 45%, 19
Insulation t = 5 s,
Leakage Current VI-I = 500 V
Resistance RI-I Dual Channel 1011 Ω 19
(Input-Input)
Capacitance CI-I Dual 8-pin DIP 0.03 pF f = 1 MHz 19
Dual SO-8 0.25
*Ratings apply to all devices except otherwise noted in the Package column.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equip-
ment level safety specication or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage.”
†For 8-pin DIP package devices (HCPL-261A/261N/263A/263N) only.
(Input-Input)
OPT 020† 5000 5, 7
11
V
OL
– LOW LEVEL OUTPUT VOLTAGE – V
-60
0.2
T
A
– TEMPERATURE – C
100
0.5
HCPL-261A fig 8
0.6
-20
0.3
20 60-40 0 40 80
0.4
V
CC
= 5.5 V
V
E
= 2 V
I
F
= 3.0 mA
I
O
= 16 mA
I
O
= 12.8 mA
I
O
= 9.6 mA
I
O
= 6.4 mA
I
OL
– LOW LEVEL OUTPUT CURRENT – mA
-60
0
T
A
– TEMPERATURE – C
100
60
HCPL-261A fig 5
80
-20
20
20
V
CC
= 5 V
V
E
= 2 V
V
OL
= 0.6 V
I
F
= 3.5 mA
60-40 0 40 80
40
I
OH
– HIGH LEVEL OUTPUT CURRENT – µA
-60
0
T
A
– TEMPERATURE – C
100
10
HCPL-261A fig 4
15
-20
5
20
V
CC
= 5.5 V
V
O
= 5.5 V
V
E
= 2 V
V
F
= 0.8 V
60-40 0 40 80
Figure 9. Test circuit for tPHL and tPLH.
VO – OUTPUT VOLTAGE – V
0
0
IF – FORWARD INPUT CURRENT – mA
2.0
4.0
HCPL-261A fig 7
5.0
1.0
2.0
0.5 1.5
3.0
1.0
RL = 4 kW
RL = 350 Ω
RL = 1 kΩ
Figure 4. Typical high level output current vs.
temperature.
I
F
– INPUT FORWARD CURRENT – mA
1.0
0.01
V
F
– FORWARD VOLTAGE – V
1.5
10.0
HCPL-261A fig 6
100.0
1.2
0.1
1.41.1 1.3
1.0
T
A
= 85 C T
A
= 40 C
T
A
= 25 C
I
F
+
–
V
F
Figure 6. Typical diode input forward current
characteristic.
Figure 5. Low level output current vs. tempera-
ture.
Figure 7. Typical output voltage vs. forward
input current.
Figure 8. Typical low level output voltage vs.
temperature.
HCPL-261A fig 9
OUTPUT V
MONITORING
NODE
O
1.5 V
tPHL tPLH
IF
INPUT
O
V
OUTPUT
I = 3.5 mA
F
I = 1.75 mA
F
+5 V
7
5
6
8
2
3
4
1
PULSE GEN.
Z = 50 Ω
t = t = 5 ns
O
f
IF
L
R
RM
CC
V
0.1 µF
BYPASS
*CL
*C IS APPROXIMATELY 15 pF WHICH INCLUDES
PROBE AND STRAY WIRING CAPACITANCE.
L
GND
INPUT
MONITORING
NODE
r
HCPL-261A/261N
90% 90%
10% 10%
trise tfall
VOH
VOL
HCPL-261A fig 9b (new)
12
t
r
, t
f
– RISE, FALL TIME – ns
-60
0
T
A
– TEMPERATURE – C
100
140
HCPL-261A fig 14
160
-20
40
20 60-40 0 40 80
60
120
20
V
CC
= 5 V
I
F
= 3.5 mA
R
L
= 4 kΩ
R
L
= 1 kΩ
R
L
= 350 Ω, 1 kΩ, 4 kΩ
t
rise
t
fall
R
L
= 350 Ω
PWD – ns
-60
0
T
A
– TEMPERATURE – C
100
50
HCPL-261A fig 13
60
-20
20
20 60-40 0 40 80
30
40
10
R
L
= 1 kΩ
R
L
= 350 Ω
V
CC
= 5 V
I
F
= 3.5 mA
R
L
= 4 kΩ
t
p
– PROPAGATION DELAY – ns
0
0
I
F
– PULSE INPUT CURRENT – mA
12
100
HCPL-261A fig 12
120
2
40
6 84 10
60
80
20
TPLH
R
L
= 4 kΩ
V
CC
= 5 V
T
A
= 25 C
TPLH
R
L
= 1 kΩ
TPHL
RL = 350 Ω, 1 kΩ, 4 kΩ
TPLH
R
L
= 350 Ω
t
p
– PROPAGATION DELAY – ns
-60
0
T
A
– TEMPERATURE – C
100
100
HCPL-261A fig 11
120
-20
40
20 60-40 0 40 80
60
80
20
TPLH
R
L
= 4 kΩ
TPLH
R
L
= 1 kΩ
TPLH
R
L
= 350 kΩ
TPHL
R
L
= 350 Ω, 1 kΩ, 4 kΩ
V
CC
= 5 V
I
F
= 3.5 mA
I
TH
– INPUT THRESHOLD CURRENT – mA
-60
0
T
A
– TEMPERATURE – C
100
1.5
HCPL-261A fig 10
2.0
-20
0.5
20 60-40 0 40 80
1.0
V
CC
= 5 V
V
O
= 0.6 V
R
L
= 350 Ω
R
L
= 1 kΩ
R
L
= 4 kΩ
Figure 10. Typical input threshold current vs.
temperature.
Figure 13. Typical pulse width distortion vs.
temperature.
Figure 11. Typical propagation delay vs. tem-
perature.
Figure 12. Typical propagation delay vs. pulse
input current.
Figure 14. Typical rise and fall time vs. temperature.
13
HCPL-261A Fig 17
V
O
0.5 V
O
V (min.)
5 V
0 V SWITCH AT A: I = 0 mA
F
SWITCH AT B: I = 3.5 mA
F
CM
V
H
CM
CM
L
O
V (max.)
CM
V (PEAK)
V
O
+5 V
7
5
6
8
2
3
4
1
CC
V
0.1 µF
BYPASS
GND
OUTPUT V
MONITORING
NODE
O
PULSE GEN.
Z = 50
Ω
O
+_
350
Ω
I
F
BA
V
FF
CM
V
HCPL-261A/261N
tE – ENABLE PROPAGATION DELAY – ns
-60
0
TA – TEMPERATURE – C
100
90
HCPL-261A fig 16
120
-20
30
20 60-40 0 40 80
60
VCC = 5 V
VEH = 3 V
VEL = 0 V
IF = 3.5 mA
tELH, RL = 4 kΩ
tELH, RL = 1 kΩ
tEHL, RL = 350 Ω, 1k Ω, 4 kΩ
tELH, RL = 350 Ω
OUTPUT V
MONITORING
NODE
O
1.5 V
t
EHL
t
ELH
V
E
INPUT
O
V
OUTPUT
3.0 V
1.5 V
+5 V
7
5
6
8
2
3
4
1
PULSE GEN.
Z = 50 Ω
t = t = 5 ns
O
f
I
F
L
R
CC
V
0.1 µF
BYPASS
*C
L
*C IS APPROXIMATELY 15 pF WHICH INCLUDES
PROBE AND STRAY WIRING CAPACITANCE.
L
GND
r
3.5 mA
INPUT V
E
MONITORING NODE
HCPL-261A/261N
HCPL-261A fig 15
Figure 15. Test circuit for tEHL and tELH.
Figure 17. Test circuit for common mode transient immunity and typical waveforms.
Figure 16. Typical enable propagation delay vs. temperature.
HCPL-261A/-261N/-061A/-061N Only.
Figure 18. Thermal derating curve, dependence of safety limiting
value with case temperature per IEC/EN/DIN EN 60747-5-2.
HCPL-261A fig 18
OUTPUT POWER – PS, INPUT CURRENT – IS
0
0
TS – CASE TEMPERATURE – C
20050
400
12525 75 100 150
600
800
200
100
300
500
700
PS (mW)
IS (mA)
HCPL-261A/261N OPTION 060 ONLY
175
14
Figure 20. Recommended drive circuit for HCPL-261A/-261N families for high-CMR (similar for HCPL-
263A/-263N).
Application Information
Common-Mode Rejection for HCPL-
261A/HCPL-261N Families:
Figure 20 shows the recommended
drive circuit for the HCPL-261N/-
261A for optimal common-mode
rejection performance. Two main
points to note are:
1. The enable pin is tied to VCC rather
than oating (this applies to
single-channel parts only).
2. Two LED-current setting resistors
are used instead of one. This is
to balance ILED variation during
common-mode transients.
If the enable pin is left oating, it is
possible for common-mode tran-
sients to couple to the enable pin,
resulting in common-mode failure.
This failure mechanism only occurs
when the LED is on and the output
is in the Low State. It is identied as
occurring when the transient output
voltage rises above 0.8 V. Therefore,
the enable pin should be connected
to either VCC or logic-level high for
best common-mode performance
with the output low (CMRL). This
failure mechanism is only present
in single-channel parts (HCPL-261N,
-261A, -061N, -061A) which have the
enable function.
Also, common-mode transients can
capacitively couple from the LED an-
ode (or cathode) to the output-side
ground causing current to be shunt-
ed away from the LED (which can be
bad if the LED is on) or conversely
cause current to be injected into the
LED (bad if the LED is meant to be
o). Figure 21 shows the parasitic
capacitances which exists between
LED anode/cathode and output
ground (CLA and CLC). Also shown in
Figure 21 on the input side is an AC-
equivalent circuit.
*Higher CMR may be obtainable by connecting pins 1, 4 to input ground (Gnd1).
SINGLE CHANNEL PRODUCTS
0.01 µF
350
Ω
HCPL-261A fig 19
74LS04
OR ANY TOTEM-POLE
OUTPUT LOGIC GATE
VO
VCC+
8
7
6
1
3
SHIELD 5
2
4
HCPL-261A/261N
GND
GND2
357
Ω
(MAX.)
VCC
357
Ω
(MAX.)
*
*
* HIGHER CMR MAY BE OBTAINABLE BY CONNECTING PINS 1, 4 TO INPUT GROUND (GND1).
GND1
Figure 19. Recommended printed circuit board layout.
DUAL CHANNEL PRODUCTS
ENABLE
(IF USED)
GND BUS (BACK)
V BUS (FRONT)
CC
N.C.
N.C.
N.C.
N.C.
OUTPUT 1
OUTPUT 2
ENABLE
(IF USED)
0.1µF
0.1µF
10 mm MAX. (SEE NOTE 16)
GND BUS (BACK)
V BUS (FRONT)
CC
OUTPUT 1
OUTPUT 2
0.1µF
10 mm MAX. (SEE NOTE 16)
15
Figure 22. TTL interface circuit for the HCPL-261A/-261N families.
420 Ω
(MAX)
HCPL-�261A fig 21
1
3
2
4
2N3906
(ANY PNP)
V
CC
74L504
(ANY
TTL/CMOS
GATE)
HCPL-261X
LED
Table 1 indicates the directions of ILP and ILN ow depend-
ing on the direction of the common-mode transient.
For transients occurring when the LED is on, common-
mode rejection (CMRL, since the output is in the “low”
state) depends upon the amount of LED current drive (IF).
For conditions where IF is close to the switching thresh-
old (ITH), CMRL also depends on the extent which ILP and ILN
balance each other. In other words, any condition where
common-mode transients cause a momentary decrease
in IF (i.e. when dVCM/dt>0 and |IFP| > |IFN|, referring to Table
1) will cause common-mode failure for transients which
are fast enough.
Likewise for common-mode transients which occur
when the LED is o (i.e. CMRH, since the output is “high”),
if an imbalance between ILP and ILN results in a transient
IF equal to or greater than the switching threshold of the
optocoupler, the transient “signal” may cause the output
to spike below 2 V (which constitutes a CMRH failure).
By using the recommended circuit in Figure 20, good
CMR can be achieved. (In the case of the -261N families,
a minimum CMR of 15 kV/µs is guaranteed using this cir-
cuit.) The balanced ILED-setting resistors help equalize ILP
and ILN to reduce the amount by which ILED is modulated
from transient coupling through CLA and CLC.
CMR with Other Drive Circuits
CMR performance with drive circuits other than that
shown in Figure 20 may be enhanced by following these
guidelines:
1. Use of drive circuits where current is shunted from
the LED in the LED “o” state (as shown in Figures 22
and 23). This is benecial for good CMRH.
2. Use of IFH > 3.5 mA. This is good for high CMRL.
Using any one of the drive circuits in Figures 22-24 with
IF = 10 mA will result in a typical CMR of 8 kV/µs for the
HCPL-261N family, as long as the PC board layout prac-
tices are followed. Figure 22 shows a circuit which can
be used with any totem-pole-output TTL/LSTTL/HCMOS
logic gate. The buer PNP transistor allows the circuit to
be used with logic devices which have low current-sink-
ing capability. It also helps maintain the driving-gate
power-supply current at a constant level to minimize
ground shifting for other devices connected to the in-
put-supply ground.
When using an open-collector TTL or open-drain CMOS
logic gate, the circuit in Figure 23 may be used. When
using a CMOS gate to drive the optocoupler, the circuit
shown in Figure 24 may be used. The diode in parallel
with the RLED speeds the turn-o of the optocoupler
LED.
Figure 21. AC equivalent circuit for HCPL-261X.
350 Ω
HCPL-�261A fig 20
1/2 R
LED
V
CC
+
15 pF
+
V
CM
8
7
6
1
3
SHIELD 5
2
4
C
LA
V
O
GND
0.01 µF
1/2 R
LED
C
LC
I
LN
I
LP
–
Figure 24. CMOS gate drive circuit for HCPL-261A/-261N families.Figure 23. TTL open-collector/open drain gate drive circuit for
HCPL-261A/-261N families.
820 Ω
HCPL-�261A fig 22
1
3
2
4
VCC
74HC00
(OR ANY
OPEN-COLLECTOR/
OPEN-DRAIN
LOGIC GATE)
HCPL-261X
LED
750 Ω
HCPL-�261A fig 23
1
3
2
4
VCC
74HC04
(OR ANY
TOTEM-POLE
OUTPUT LOGIC
GATE)
HCPL-261A/261N
1N4148
LED
Propagation Delay, Pulse-Width Distortion and Propa-
gation Delay Skew
Propagation delay is a gure of merit which describes
how quickly a logic signal propagates through a sys-
tem. The propagation delay from low to high (tPLH) is the
amount of time required for an input signal to propa-
gate to the output, causing the output to change from
low to high. Similarly, the propagation delay from high
to low (tPHL) is the amount of time required for the input
signal to propagate to the output, causing the output to
change from high to low (see Figure 9).
Pulse-width distortion (PWD) results when tPLH and tPHL
dier in value. PWD is dened as the dierence between
tPLH and tPHL and often determines the maximum data
rate capability of a transmission system. PWD can be
expressed in percent by dividing the PWD (in ns) by the
minimum pulse width (in ns) being transmitted. Typi-
cally, PWD on the order of 20-30% of the minimum pulse
width is tolerable; the exact gure depends on the par-
ticular application (RS232, RS422, T-1, etc.).
Propagation delay skew, tPSK, is an important parameter
to consider in parallel data applications where synchro-
nization of signals on parallel data lines is a concern. If
the parallel data is being sent through a group of opto-
couplers, dierences in propagation delays will cause
the data to arrive at the outputs of the optocouplers at
dierent times. If this dierence in propagation delay
is large enough it will determine the maximum rate at
which parallel data can be sent through the optocou-
plers.
Propagation delay skew is dened as the dierence be-
tween the minimum and maximum propagation delays,
either tPLH or tPHL, for any given group of optocouplers
which are operating under the same conditions (i.e., the
same drive current, supply voltage, output load, and op-
erating temperature). As illustrated in Figure 25, if the in-
puts of a group of optocouplers are switched either ON
or OFF at the same time, tPSK is the dierence between
the shortest propagation delay, either tPLH or tPHL, and the
longest propagation delay, either tPLH or tPHL.
As mentioned earlier, tPSK can determine the maximum
parallel data transmission rate. Figure 26 is the timing
diagram of a typical parallel data application with both
the clock and the data lines being sent through opto-
couplers.
Table 1. Eects of Common Mode Pulse Direction on Transient ILED
If |ILP| < |ILN|, If |ILP| > |ILN|,
LED IF Current LED IF Current
If dVCM/dt Is: then ILP Flows: and ILN Flows: Is Momentarily: Is Momentarily:
positive (>0) away from LED away from LED increased decreased
anode through CLA cathode through CLC
negative (<0) toward LED toward LED decreased increased
anode through CLA cathode through CLC
Figure 25. Illustration of propagation delay skew – tPSK.
50%
1.5 V
IF
VO
50%I F
VO
tPSK
1.5 V
HCPL-261A fig 24
TPHL
TPLH
Figure 26. Parallel data transmission example.
HCPL-2602 fig 17
DATA
tPSK
INPUTS
CLOCK
DATA
OUTPUTS
CLOCK
tPSK
The gure shows data and clock signals at the inputs and
outputs of the optocouplers. To obtain the maximum
data transmission rate, both edges of the clock signal are
being used to clock the data; if only one edge were used,
the clock signal would need to be twice as fast.
Propagation delay skew represents the uncertainty of
where an edge might be after being sent through an op-
tocoupler. Figure 26 shows that there will be uncertainty
in both the data and the clock lines. It is important that
these two areas of uncertainty not overlap, otherwise
the clock signal might arrive before all of the data out-
puts have settled, or some of the data outputs may start
For product information and a complete list of distributors, please go to our website: www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries.
Data subject to change. Copyright © 2007 Avago Technologies Limited. All rights reserved. Obsoletes AV01-0561EN
AV02-0391 - December 6, 2007
to change before the clock signal has arrived. From these
considerations, the absolute minimum pulse width that
can be sent through optocouplers in a parallel applica-
tion is twice tPSK. A cautious design should use a slightly
longer pulse width to ensure that any additional uncer-
tainty in the rest of the circuit does not cause a prob-
lem.
The tPSK specied optocouplers oer the advantages of
guaranteed specications for propagation delays, pulse-
width distortion, and propagation delay skew over the
recommended temperature, input current, and power
supply ranges.