MGJ2 Series www.murata-ps.com 5.2kVDC Isolated 2W Gate Drive DC-DC Converters ANSI/AAMI ES60601-1, 1 MOPP/2 MOOP's recognised4 5.2kVDC isolation test voltage `Hi Pot Test' Ultra low coupling capacitance SIP package style 5V, 12V, 15V & 24V inputs +15V/-15,V +15V/-5V, +15V/-8.7V, +20V/-3.5 & +20V/-5V outputs Operation to 100oC Characterised dv/dt immunity 80kV/S at 1.5kV MGJ2D051505SC MGJ2D051509SC MGJ2D051515SC MGJ2D052005SC MGJ2D121505SC MGJ2D121509SC MGJ2D121515SC MGJ2D122005SC MGJ2D151505SC MGJ2D151509SC MGJ2D151515SC MGJ2D152003SC MGJ2D152005SC MGJ2D241505SC MGJ2D241509SC MGJ2D241709SC MGJ2D242005SC The MGJ2 series of DC-DC converters is ideal for powering `high side' and `low side' gate drive circuits for IGBTs and Mosfets in bridge circuits. A choice of asymmetric output voltages allows optimum drive levels for best system efficiency and EMI. The MGJ2 series is characterised for high isolation and dv/dt requirements commonly seen in bridge circuits used in motor drives and inverters, while the MGJ2 industrial grade temperature rating and construction gives long service life and reliability. % 360 390 492 440 150 155 203 195 120 130 167 150 145 75 80 105 90 5.7 6 7 6.2 4.7 5.3 6.0 5.5 5 5 5.5 7 6 4.6 4.8 6 6 7 7 8.5 8 6 7.5 7 8 7 7 7 10 8 7 7 8 8 mVp-p 30 50 30 50 20 35 30 50 30 50 30 50 24 40 30 45 30 50 30 50 23 35 30 50 30 50 30 50 30 50 30 50 30 50 % 71 73 74 74 76 76 78 78 75 76 75 76 78 75 77 78 78 pF 76 2.8 77.5 3.3 78 4 78.5 3.3 80 2.9 80 3.5 82 4 82 3.3 80 2.9 80 4 79 4 81 3 81 3.4 80.5 2.7 82 3.5 83 3.5 82 3.5 MTTF1 MIL. Tel. kHrs 2095 1902 2629 1655 2339 2296 2707 1799 2374 2736 2100 2000 80000 1864 2194 2275 1050 47000 1725 INPUT CHARACTERISTICS Parameter Voltage range Characterised partial discharge performance PRODUCT OVERVIEW 80 80 67 80 80 80 67 80 80 80 67 80 80 80 80 80 80 mA 40 40 67 40 40 40 67 40 40 40 67 80 40 40 40 80 40 Isolation Capacitance V -5 -8.7 -15 -5 -5 -8.7 -15 -5 -5 -8.7 -15 -3.5 -5 -5 -8.7 -9V -5 Input Current at Rated Load Load Regulation (Typ) Load Regulation (Max) Ripple & Noise (Typ)2 Ripple & Noise (Max)2 Efficiency (Min) Efficiency (Typ) V 15 15 15 20 15 15 15 20 15 15 15 20 20 15 15 17 20 Output Current 2 Reinforced insulation to UL60950 recognised3 V 5 5 5 5 12 12 12 12 15 15 15 15 15 24 24 24 24 Output Current 1 Optimised bipolar output voltages for IGBT/ Mosfet gate drives Output Voltage 2 FEATURES Output Voltage 1 Order Code Nominal Input Voltage SELECTION GUIDE Input reflected ripple Conditions Min. Typ. Max. Units Continuous operation, 5V input types Continuous operation, 12V input types Continuous operation, 15V input types Continuous operation, 24V input types 5V input types 12V & 15V input types 24V input types 4.5 10.8 13.5 21.6 5 12 15 24 40 20 15 5.5 13.2 16.5 26.4 V Typ. Max. mA ISOLATION CHARACTERISTICS Parameter Isolation test voltage Resistance Conditions Min. Production tested for 1 second Qualification tested for 1 minute Viso= 500VDC 5200 5200 Units VDC 1 G OUTPUT CHARACTERISTICS Parameter Conditions TA=-40C to 100C Rated Power Voltage Set Point Accuracy Line regulation Min. See tolerance envelopes High VIN to low VIN Typ. Max. Units 2 W 1.0 1.2 %/% Typ. Max. Units GENERAL CHARACTERISTICS Parameter Conditions Switching frequency All types Min. 45 kHz 1. Calculated using MIL-HDBK-217 FN2 calculation model with nominal input voltage at full load. 2. See ripple & noise test method. 3. UL60950 recognition is currently pending for the MGJ2D241709SC. 4. ANSI/AAMI ES60601-1 recognition is currently pending for the MGJ2D241709SC. For full details go to www.murata-ps.com/rohs All specifications typical at TA=25C, nominal input voltage and rated output current unless otherwise specified. www.murata-ps.com/support KDC_MGJ2_G01Page 1 of 9 MGJ2 Series 5.2kVDC Isolated 2W Gate Drive DC-DC Converters TEMPERATURE CHARACTERISTICS Parameter Conditions Min. Specification Storage All output types (see safety approval section for limitations) -40 -55 Typ. Max. Units 100 125 5V input types 24 All other input types 20 C Case Temperature above ambient Cooling Free air convection ABSOLUTE MAXIMUM RATINGS Short-circuit protection Lead temperature 1mm from case for 10 seconds Input voltage VIN, MGJ2D05xxxxSC Input voltage VIN, MGJ2D12xxxxSC Input voltage VIN, MGJ2D15xxxxSC Input voltage VIN, MGJ2D24xxxxSC Continuous 260C 5.5V 13.2V 16.5V 26.4V www.murata-ps.com/support KDC_MGJ2_G01Page 2 of 9 MGJ2 Series 5.2kVDC Isolated 2W Gate Drive DC-DC Converters TECHNICAL NOTES ISOLATION VOLTAGE `Hi Pot Test', `Flash Tested', `Withstand Voltage', `Proof Voltage', `Dielectric Withstand Voltage' & `Isolation Test Voltage' are all terms that relate to the same thing, a test voltage, applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. Murata Power Solutions MGJ2 series of DC-DC converters are all 100% production tested at 5.2kVDC for 1 second and have been qualification tested at 5.2kVDC for 1 minute. A question commonly asked is, "What is the continuous voltage that can be applied across the part in normal operation?" When the insulation in the MGJ2 series is not used as a safety barrier , i.e. provides functional isolation only, continuous or switched voltages across the barrier in excess of 1.5kV are sustainable. Long term reliability testing at these voltages continues. Please contact Murata for further information. The MGJ2 series is recognised by Underwriters Laboratory for various voltages, please see safety approval section below. REPEATED HIGH-VOLTAGE ISOLATION TESTING It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials, construction and environment. We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be SAFETY APPROVAL ANSI/AAMI ES60601-1 The MGJ2 series has been recognised by Underwriters Laboratory (UL) to ANSI/AAMI ES60601-1 and provides 1 MOOP (Means Of Operator Protection) based on a working voltage of 300Vrms or 2 MOOP based upon a working voltage of 200 Vrms, and 1 MOPP (Mean Of Patient Protection) based on a working voltage of 200Vrms., between Primary and Secondary. The MGJ2D241709SC is currently pending recognition. File number E202895 applies. UL 60950 The MGJ2 series is recognised by Underwriters Laboratory (UL) to UL 60950 for reinforced insulation to a working voltage of 150Vrms and for basic/supplementary insulation to a working voltage of 300Vrms. The MGJ2D241709SC is currently pending recognition. File number E151252 applies. Creepage and clearance 3mm. Fusing The MGJ2 Series of converters are not internally fused so to meet the requirements of UL an anti-surge input line fuse should always be used with ratings as defined below. MGJ2x05xxxC: 1.25A MGJ2x12xxxC: 750mA MGJ2x15xxxC: 750mA MGJ2x24xxxC: 750mA All fuses should be UL recognized and rated to 125V. RoHS COMPLIANCE INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 260C for 10 seconds. The pin termination finish on this product series is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The series is backward compatible with Sn/Pb soldering systems. For further information, please visit www.murata-ps.com/rohs www.murata-ps.com/support KDC_MGJ2_G01Page 3 of 9 MGJ2 Series 5.2kVDC Isolated 2W Gate Drive DC-DC Converters APPLICATION NOTES Minimum load The minimum load to meet datasheet specification is 10% of the full rated load across the specified input voltage range. Lower than 10% minimum loading will result in an increase in output voltage, which may rise to typically 1.25 times the specified output voltage if the output load falls to less than 5%. Capacitive loading and start up Typical start up times for this series, with a typical input voltage rise time of 2.2s and output capacitance of 10F, are shown in the table below. The product series will start into capacitance ranging from 47F up to 220F with increased start times. MGJ2D051505SC MGJ2D051509SC MGJ2D051515SC MGJ2D052005SC MGJ2D121505SC MGJ2D121509SC MGJ2D121515SC MGJ2D122005SC MGJ2D151505SC MGJ2D151509SC MGJ2D151515SC MGJ2D152003SC MGJ2D152005SC MGJ2D241505SC MGJ2D241509SC MGJ2D241709SC MGJ2D242005SC Start-up time ms 3.3 4.5 20.84 5.4 3.2 4 14.54 5.5 2.5 3 10.48 4.5 4.5 2.7 3 4 4.2 Typical Start-Up Wave Form Ripple & Noise Characterisation Method Ripple and noise measurements are performed with the following test configuration. C1 1F X7R multilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC-DC converter 10F tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC-DC converter with an ESR of less C2 than 100m at 100 kHz C3 100nF multilayer ceramic capacitor, general purpose R1 450 resistor, carbon film, 1% tolerance R2 50 BNC termination T1 3T of the coax cable through a ferrite toroid RLOAD Resistive load to the maximum power rating of the DC-DC converter. Connections should be made via twisted wires Measured values are multiplied by 10 to obtain the specified values. Differential Mode Noise Test Schematic DC/DC Converter OSCILLOSCOPE C1 C2 C3 + SUPPLY Input - + R1 T1 R2 Y INPUT Output - R LOAD www.murata-ps.com/support KDC_MGJ2_G01Page 4 of 9 MGJ2 Series 5.2kVDC Isolated 2W Gate Drive DC-DC Converters EFFICIENCY VS LOAD 5V INPUT 12V INPUT 90 90 80 80 70 70 60 MGJ2D051505SC 50 MGJ2D051509SC MGJ2D052005SC 40 MGJ2D051515SC Efficiency (%) Efficiency (%) 60 MGJ2D121509SC MGJ2D122005SC 40 30 30 20 20 10 10 0 MGJ2D121505SC 50 MGJ2D121515SC 0 0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 40 50 Load (%) 15V INPUT 70 80 90 100 24V INPUT 90 90 80 80 70 70 60 MGJ2D151505SC MGJ2D151509SC 50 MGJ2D152003SC MGJ2D152005SC 40 MGJ2D151515SC Efficiency (%) Efficiency (%) 60 Load (%) 60 MGJ2D241505SC 50 MGJ2D241709SC 30 30 20 20 10 MGJ2D241509SC 40 MGJ2D242005SC 10 0 0 10 20 30 40 50 60 70 80 90 100 0 0 10 20 30 40 Load (%) 50 60 70 80 90 100 Load (%) TEMPERATURE DERATING GRAPHS -40 85 0 40 Ambient Temperature (C) Full Output Current Rating Full Output Current Rating Safe Operating Area Safe Operating Area -40 95 0 40 Ambient Temperature (C) All other varients Full Output Current Rating MGJ2D051505SC & MGJ2D052005SC MGJ2D051515SC, MGJ2D121515SC & MGJ2D151515SC Safe Operating Area -40 100 0 40 Ambient Temperature (C) www.murata-ps.com/support KDC_MGJ2_G01Page 5 of 9 MGJ2 Series 5.2kVDC Isolated 2W Gate Drive DC-DC Converters POSITIVE OUTPUT VOLTAGE TOLERANCE ENVELOPES The voltage tolerance envelopes show typical load regulation characteristics for this product series. The tolerance envelope is the maximum output voltage variation due to changes in output loading and set point accuracy. 4% 2% 1% -4% 10 75 50 25 Output Load Current (%) MGJ2D122005SC, MGJ2D152005SC & MGJ2D242005SC Output Voltage Output Voltage MGJ2D051505SC, MGJ2D051509SC, MGJ2D151505SC & MGJ2D151509SC 3% 2% -1% -5% 100 10 4% 1% 0% MGJ2D121505SC & MGJ2D241505SC Output Voltage Output Voltage MGJ2D121509SC, MGJ2D241509SC & MGJ2D052005SC 100 50 75 25 Output Load Current (%) 5% 3% 2% -3% -7% 10 75 50 25 Output Load Current (%) 100 10 MGJ2D121515SC & MGJ2D151515SC 50 75 25 Output Load Current (%) 100 MGJ2D152003SC 3% 1% -4% 10 75 50 25 Output Load Current (%) 100 Output Voltage Output Voltage 6% 4% 1% 0% -6% 10 75 50 25 Output Load Current (%) 100 www.murata-ps.com/support KDC_MGJ2_G01Page 6 of 9 MGJ2 Series 5.2kVDC Isolated 2W Gate Drive DC-DC Converters POSITIVE OUTPUT VOLTAGE TOLERANCE ENVELOPES CONTINUED MGJ2D051515SC MGJ2D241709SC 7% 1% 0% Output Voltage Output Voltage 6% 3.5% 3% -3% -7% 10 75 50 25 Output Load Current (%) 10 100 75 50 25 Output Load Current (%) 100 NEGATIVE OUTPUT VOLTAGE TOLERANCE ENVELOPES MGJ2D051509SC, MGJ2D052005SC & MGJ2D121505SC, MGJ2D122005SC, MGJ2D152005SC & MGJ2D242005SC MGJ2D151505SC 8% 6% 3% 2% -4% 10 75 50 25 Output Load Current (%) 4% Output Voltage Output Voltage 7% 0% 10 100 4% 1% 1% -6% 10 75 50 25 Output Load Current (%) 100 MGJ2D051505SC 100 Output Voltage Output Voltage MGJ2D121509SC & MGJ2D241509SC 75 50 25 Output Load Current (%) 5% 3% 1% -4% 10 75 50 25 Output Load Current (%) 100 www.murata-ps.com/support KDC_MGJ2_G01Page 7 of 9 MGJ2 Series 5.2kVDC Isolated 2W Gate Drive DC-DC Converters NEGATIVE OUTPUT VOLTAGE TOLERANCE ENVELOPES CONTINUED MGJ2D151509SC & MGJ2D241505SC MGJ2D121515SC & MGJ2D151515SC 6% 3% 2% -3% 10 75 50 25 Output Load Current (%) Output Voltage Output Voltage 6% 3% 1% -4% 10 100 MGJ2D051515SC 75 50 25 Output Load Current (%) 100 MGJ2D152003SC 8% 1% 0% Output Voltage Output Voltage 6% 4% 3% -4% -7% 10 75 50 25 Output Load Current (%) 10 100 75 50 25 Output Load Current (%) 100 MGJ2D241709SC Output Voltage 6.5% 3% 2% -4% 10 75 50 25 Output Load Current (%) 100 www.murata-ps.com/support KDC_MGJ2_G01Page 8 of 9 MGJ2 Series 5.2kVDC Isolated 2W Gate Drive DC-DC Converters PACKAGE SPECIFICATIONS MECHANICAL DIMENSIONS PIN CONNECTIONS Pin Output All dimensions in mm 0.25mm (inches 0.01). All pins on a 2.54 (0.1) pitch and within 0.25 (0.01) of true position. TUBE OUTLINE DIMENSIONS Unless otherwise stated all dimensions in mm 0.5mm (inches 0.02). Tube length : 20.6690.079 (525mm2mm). Pin Function 1 2 5 6 7 +VIN -VIN -VOUT OV +VOUT Weight: 4.3g RECOMMENDED FOOTPRINT DETAILS Tube Quantity : 25 All dimensions in mm 0.25mm (inches 0.01). This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. (c) 2018 Murata Power Solutions, Inc. www.murata-ps.com/support KDC_MGJ2_G01Page 9 of 9