1SD210F2
IGBT-Driver.com Page 1
Data Sheet
1SD210F2-5SNA0600G650100
Single-Channel SCALE Plug-and-Pl a y IGBT
Driver
Ultra compact, high-performance driver for 2-level, 3-level and
multilevel converters
Abstract
The SCALE plug-and-play driver 1SD210F2-5SNA0600G650100 is a compact
single-channel intelligent gate driver designed for ABB’s high-voltage IGBTs
of type 5SNA0600G650100. The driver features a fiber-optic interface and a
selectable operation mode via a jumper.
For drive rs adapted to other types of h igh-power and hi gh-voltage IG BT modules, re fer
to www.IGBT-Driver.com/go/plug-and-play
Product Highlights Applications
Plug-and-play solution Three/multi-level converters
Protects the IGBT from short-circui t failure Two-level converters
Active clamping of Vce at turn-off Medium-voltage converters
Extremely reliable; long service life High-voltag e ap plications
No electro lytic capacitor s Industrial drives
Gate curr ent up to –6A/+10A Traction
Fiber-optic links Railroad pow er supplies
Monitoring of supply volt age and fiber opti cs Wind-power converters
Switching fr eq uenc y DC to max. 6kHz Radiology and laser technology
Duty cycle 0... 100% Research
Suitab le DC /DC power supply a s separate unit Almost all other c onceivable
Shortens application development time applications
1SD210F2
Data Sheet 1SD210F2-5SNA0600G650100
Page 2 CT-Concept.com
Important Notes
This data sheet contains only product-specific data. For a detailed description, must-
read application notes and common data that apply to the whole series, please refer to
the “Description and Application Manual for 1SD210F2 SCALE High-Voltage IGBT
Drivers”.
When applying SCALE plug-and-play drivers, please note that these drivers are
specifically adapted to a particular type of IGBT module. Therefore, the type
designation of SCALE plug-and-play drivers also includes the type designation of the
corresponding IGBT module. These drivers are not valid for IGBT modules other
than those specified. Incorrect use may result in failure.
Mechanical and Electrical Interfaces
Dimensio ns: 156 x 79.5 mm .
Mounting P r i nc i ple: Direct screw m ount on IGBT.
Interface Remarks Part type #
Drive signal inp ut (Standard) Fiber-optic receiver (Notes 14,16) HFBR-2522
Drive signal inp ut (Opt. 01) Fiber-optic receiver (Notes 14,16) HFBR-2522
Drive signal inp ut (Opt. 02) Fiber-optic receiver (Notes 14,20) HFBR-2412T
Status output (Standard) Fiber-optic transmitter (Notes 14,17) HFBR-1522
Status output (Opt. 01) Fiber-optic transmitter (Notes 14,17) HFBR-1522
Status output (Opt. 02) Fiber-optic transmitter (Notes 14,21) HFBR-1412T
Power supp ly c onnector On-board connector (Note 15) 77315-101-05
Power supply connector Designator Pin numbers
Ground GND (Note 19) 1, 2, 4, 5
Supply voltage
VDC
3
1SD210F2
Data Sheet 1SD210F2-5SNA0600G650100
IGBT-Driver.com Page 3
Absolute Maximum Ratings
Parameter Remarks Min Max Units
Supply voltage
VDC
VDC to GND (Note 1) 0 17.3 V
Gate pea k current
Iout
Note 8 -6 +10 A
Average supp ly c ur r ent
IDC
Standard and Opt. 1 (Note 3) 190 mA
Opt. 2 (No te 3) 225 mA
Output power gate driver Notes 3,11 2 W
Switching fr equency Note 11 6 kHz
DC-link volt age Note 5 4400 V
Operating temperature Note 11 -40 +85 °C
Storage temperature -40 +90 °C
Electrical Characteristics
All data r efer to +25°C and
VDC
= 16.4V unless otherwise speci f ied
Power supply Remarks Min Typ. Max Units
Nominal supply voltage
VDC
VDC to GND (Note 1) 15.5 16.4 16.8 V
Supply current
IDC
Without loa d (Note 2)
Standard and Opt. 1 80 mA
Opt. 2 115 mA
Turn-on threshold
Vth
Note 4 14 V
Hysteresis on/o ff Note 4 1.0 V
Short-circuit protection Remarks Min Typ. Max Units
Vce-monitoring thresho ld Between aux. term inals 1200 V
Respon se time 3-level mode (Notes 10,18) 10.8 11.5 μs
Respon se time 2-level mode (Notes 6,18) 11.6 12.4 μs
Blocking t i m e 2-level mode (Note 7) 1 s
Timing characteristics Remarks Min Typ. Max Units
Turn-on delay
tpd(on)
Note 12 430 ns
Turn-off delay
tpd(off)
Note 12 520 ns
Output ri se t i m e
tr(out)
Note 9 100 ns
Output fall time
tf(out)
Note 9 100 ns
Acknowledge delay time At status output (Note 13) 450 ns
Acknowledge pulse width At status output 0.7 1.8 μs
1SD210F2
Data Sheet 1SD210F2-5SNA0600G650100
Page 4 CT-Concept.com
Gate ou tp ut Remarks Min Typ. Max Units
Turn-on gate resistor
Rg(on)
Note 22 3.9 Ω
Turn-off gate resi stor
Rg(off)
12 Ω
Footnotes to the key data
1) Suppl y volt age s hig her than those s pe cifie d ca n lea d to the de st ru ctio n o f t he d ri ve r and pro te cti on
circuits on the output side. The gate-emitter voltage tracks the supply voltage. (Not regulated by
the gat e d rive unit.) T he re comm e nded DC/ DC pow er suppl y I SO3 11 6I w ith high-voltage insulation
capability is a suitable sep arate unit.
2) Static power consumption of the gate driver.
3) If the specified power consumption of the gate driver is exceeded on average, this indicates an
overload of the gate driver and the external DC/DC power supply ISO3116I.
4) Under-voltage monitoring of supply voltage of the gate driver. For a voltage lower than this limit,
the power modules are switched off.
5) This limit is due to active clamping. Refer to t he “Description and Application Manual for 1SD210F2
SCALE H igh-Voltage IGBT Drivers”.
6) Pulse width of the direct output of the gate drive unit. (Excluding the delay of the gate resistors.)
7) Duration of blocking the command input (keeping the gate driver and the IGBT in the off-state)
after fault detection, i.e. power supply under-voltage lock out, or – only in 2-level mode – short-
circuit detection. (For three/multilevel mode, turn-off under the short-circuit condition is managed
by the host controller.)
8) The gate curre nt is limited by on-board gate resistors.
9) Refers to the direct output of the gate drive unit. (Excluding the delay of the gate resistors.)
10) Including the delay of external fiber-optic links. Measured from the turn-on transition at direct
output of the gate drive unit (excluding the delay of the gate resistors) to the transition of the
status signal at the optical receiver on the host controller side.
11) Application-specific self-heating of gate drivers and IGBT modules, especially at high switching
frequency, must be taken into account. The switching frequency is usually limited due to the
switching losses of the IGBT modules. Because CONCEPT cannot predict how the drivers will be
incorpo rated in t he user’s a pplicatio n, no bindi ng recom mended val ue for self-he ating and t hus for
the maximum useable output power can be given. It is therefore recommended to check the gate
driver’s ambient temperature within the system.
12) Including the delay of external fiber-optic links. Measured from the transition of the turn-on or
turn-off command at the optical transmitter on the host controller side to the direct output of the
gate drive unit. (E xcluding the delay of the gate resistors.)
13) Including the delay of external fiber-optic links. Measured from the transition of the turn-on or
turn-off command at the optical transmitter on the host controller side to the transition of the
acknowledge signal at the optical receiver on the host controller side.
14) The transceivers required at the host controller side are not supplied with the gate driver. It is
recommended to use the same types as used in the gate driver. For product information refer to
www.IGBT-Driver.com/go/fiberoptics
15) The connector and cable to the DC/ DC power supply are not supplied with the gate driver, but via
FCI Inc. Recommended crimp contact housing: order code 65039-032; recommended crimp
contacts: 5 p c s, order code 48236-002. Refer to www.IGBT-Driver.com/go/fci
16) The recommended transmitter current at the host controller is 30-35mA, suitable for plastic optic
fibers with a length of less than 2.5 meters. A higher current may increase jitter or delay at turn-
off.
1SD210F2
Data Sheet 1SD210F2-5SNA0600G650100
IGBT-Driver.com Page 5
17) The transmitter current at the gate driver is 30-35mA.
18) The delay from the turn-on transition at direct output of the gate drive unit to the turn-on of the
IGBT amounts to about 1.5μs (due to gate resistors). But turn-off at short circuit takes place
without delay; so the real short-circuit time is 1.5μs shorter than the response time.
19) GND o f the power suppl y is not at t he same electrical potential as t he auxiliary emitter terminal of
the IGBT. They should never be connected together.
20) The recommended transmitter current at the host controller is 60mA.
21) The transmitter current at the gate driver is about 65mA.
22) This value is the minimum recommended turn-on gate resistance with a DC-link stray inductance
of Lσ=280nH. The turn-on gate resistance can be reduced with a lower DC-link stray inductance.
Important Notice
The data contained in this product data sheet is intended exclusively for technically
trained staff. Handling all high-voltage equipment involves risk to life. Strict compliance
with the respec tive safety regulations is mandatory!
Any handling of electronic devices is subject to the general specifications for protecting
electrostatic-sensitive devices according to international standard IEC 747-1, Chapter IX
or European standard EN 100015 (i.e. the workplace, tools, etc. must comply with
these standards). Otherwise, this product may be damaged.
Disclaimer
This data sheet specifies devices but cannot promise to deliver any specific
characteristics. No warranty or guarantee is given – either expressly or implicitly –
regarding delivery, perfor m ance or suitability.
CT-Concept Technology AG reserves the right to make modifications to its technical
data and product specifications at any time without prior notice. The general terms and
conditi ons of delivery of CT -Concept Technology A G apply.
1SD210F2
Data Sheet 1SD210F2-5SNA0600G650100
Page 6 CT-Concept.com
Ordering In f orma t i o n
The general terms and conditions of delivery of CT-Concept Technologie AG apply.
Related IGBT CONCEPT Driver Type #
ABB 5SNA0600G650100 1SD210F2-5SNA0600G650100
ABB 5SNA0600G650100 1SD210F2-5SNA0 600G650 100 O pt. 01
ABB 5SNA0600G650100 1SD210F2-5SNA0 600G650 100 O pt. 02
Opt. 01: Lateral fiber-optic interface (HFBR-2522 and HFBR-1522), see “Description and Application
Manual for 1SD210F2 SCALE High-Voltage IGBT Drivers”.
Opt. 02: Lateral fiber-optic interface with threaded port (HFBR-2412T and HFBR-1412T), see “Description
and Ap plication Manual for 1SD210F2 SCALE High-Voltage IGBT Drivers”.
Information about Other Products
For drivers adapte d to other high-voltage IGBT modules
Direct link: www.IGBT-Driver.com/go/plug-and-play
For other drivers and evaluation systems
Please click: www.IGBT-Driver.com
Manufacturer
CT-Concept Technologie AG
Intelligent Power Electronics
Renferst ra sse 15
CH-2504 Biel-Bienne
Switzerland
Tel. +41 - 32 - 344 47 47
Fax +41 - 32 - 344 47 40
E-mail Info@IGBT-Driver.com
Internet www.IGBT-Driver.com
© Copyright 1999…2007 by CT-Concept Technologie AG - Switzerland. All rights reserved.
We reserve the right to make any technical modifi ca ti ons without p ri or noti ce . Version from 2016-05-20
