AS1353-18-T - AMS - Product.Network

AS1353, AS1356

Linear Low-Dropout 150mA Voltage Regulators

www.austriamicrosystems.com Revision 1.03 1 - 13

Data Sheet

1 General Description

The AS1353/AS1356 are hig h-performance, fixed-volt-

age linear LDOs designed for use with capacitors of 1 to

10µF. The devices can deliver superior performance

even under low dropout conditions when the power tran-

sistor operates in linear mode.

The integrated P-channel MOSFET output allows the

devices to maintain a low supply-current at loads of up

to150mA. A shutdown mode includes logic-control led

circuitry which reduces shutdown current to less than

1µA (max).

Integrated over-temperature and over-current protec-

tion circuitry switches the devices off in case of thermal

overload or output short-circuit conditions.

The AS1353/AS1356 are optimize d for low equivalent-

series resistance (ESR) output capacitors. Additionally,

all devices contain reversed battery protection which dis-

connects the internal circuitry and parasitic diodes if the

battery is connected incorrectly.

The AS1356 also features power-OK circuitry which can

be used to monitor output regulation.

All devices also feature an integrated error amplifier and

built-in 1.25V reference, and ou tput current is limited

(380mA typ) via the on-chip current limiting circuitry.

Multiple output voltages are available as standard prod-

ucts: 3.6, 3.3, 3.0, 2.7, 2.5, or 1.5V. All devices are avail-

able in a 5-pin SOT23 package.

Figure 1. Pinout and Application Diagrams

2 Key Features

! Ultra-Low Dropout Voltage: 40mV @ 100mA load

! Output Voltage Range: +1.5 to +3.6V (100mV steps)

! Max Output Current: 150mA

! Output Voltage Accuracy: ±1%

! Low Shutdown Current: 1µA

! High PSRR: 60dB at 100Hz

! Integrated Overtemper ature/Overcurrent Protection

! Reverse-Battery Protection (AS1353/AS1356)

! Power-OK Output (AS1356)

! Minimal External Components Required

! Operating Tempera ture Range: -40 to +85°C

! 5-pin SOT23 Package

3 Applications

The devices are ideal for powering cordless and mobile

phones, MP3 players, CD and DVD players, PDAs,

handheld computers, digital cameras, and any other

hand-held and/or battery-powered device.

AS1356

SHDNM

IN OUT

POK

CIN

1µF

+2.5 to

+5.5V COUT

1µF

100kΩ

Off

Preset Output

1.5 to 3.6V,

150mA

To Micro-

processor

AS1353

CBP

0.01µF

SHDNM

IN OUT

CIN

1µF

+2.5 to

+5.5V COUT

1µF

Off

Preset Output

1.5 to 3.6V,

150mA

GND

AS1353

3BP

OUT

GND

SHDNM

GND

AS1356

3POK

OUT

GND

SHDNM

www.austriamicrosystems.com Revision 1.03 2 - 13

AS1353/AS1356

Data Sheet - Pinout

4 Pinout

Pin Assignments

Figure 2. Pin Assignments (Top View)

Pin Descriptions

Table 1. AS1353 Pin Descriptions

Pin Number Pin Name Description

1IN

LDO Input. Supp ly voltage can range from 2.5 to 5.5V. Bypass with a 1µF

capacitor to GND (see Capacitor Selection and Regulator Stability on page 10).

2 GND Ground. This pin also functions as a heat sink. Solder to a large pad or the

circuit-board ground plane to maximize power dissipation.

3 SHDNM Active-Low Shutdown Input. A logic low reduces the supply current to < 1µA.

Note: Connect to IN for normal ope ration.

4 BP Reference-Noise Bypass. Bypass with a low-leakage, 0.01µF ceramic

capacitor for reduced noise at the output.

5 OUT LDO Output. Fixed 1.5, 2.5, 2.7, 3.0, 3.3, and 3.6V output. Sourc es up to

150mA.

Table 2. AS1356 Pin Descriptions

Pin Number Pin Name Description

1IN

LDO Input. Input voltage can range from 2.5 to 5.5V. Bypass with 1µF to GND

(see Capacitor Selection and Regulator Stability on page 10).

2GND

Ground. This pin also functions as a heat sink. Solder to a large pad or the

circuit-board ground plane to maximize power dissipation.

3 SHDNM Active-Low Shutdown Input. A logic low reduces the supply current to < 1µA.

Note: Connect to pin IN for normal operation.

4POK

Power-OK Output. Active-low , open-drain output indicates an out-of-regulation

condition. Connect a 100kΩ pull-up resist or to pi n OUT for logic levels.

Note: Leave this pin unconnected if the power-OK feature is not used.

5OUT

LDO Output. Fixed 1.5, 2.5, 2.7, 3.0, 3.3, and 3.6V output. Sourc es up to

150mA.

3POK

OUT

GND

SHDNM

3BP

OUT

GND

SHDNM

AS1356

AS1353

www.austriamicrosystems.com Revision 1.03 3 - 13

AS1353/AS1356

Data Sheet - Absolute Maximum Ratings

5 Absolute Maximum Ratings

Stresses beyond those li st ed in Table 3 ma y cau s e pe rmanent damage to the device. These are stress ratings only,

and functional operation of the device at these or any othe r conditions beyond those indicated in Section 6 Electrical

Characteristics on page 4 is not implied. Exposure to absolute maximum rating conditions for extended periods may

affect device reliability.

Table 3. Absolute Maximum Ratings

Parameter Min Max Typ Units Comments

IN, SHDNM to GND -7 +7 V

SHDNM to IN -7 +0.3 V

POK, BP, OUT to GND -0.3 VIN +

+0.3 V

Output Short-Circuit Duration Indefinite V

Continuous Power Dissipation

(TAMB = +70ºC) 571 mW Derate 7.1mW/ºC above +70ºC

Operating Temperature Range -40 +85 ºC

Junction Temperature +150 ºC Internally limited

ΘJA +140 ºC/W

Storage Temperature Range -65 +150 ºC

Package Body Temperature +260 ºC

The reflow peak soldering te mp erature

(body temperature) specified is in

accordance with IPC/JEDEC J-STD-020C

“Moisture/Reflow Sensitivity Classification

for non-hermetic Solid State Surface

Mount Devices”

www.austriamicrosystems.com Revision 1.03 4 - 13

AS1353/AS1356

Data Sheet - Electrical Characteristics

6 Electrical Characteristics

(VIN = VOUT(Nominal) + 1V, SHDNM = IN, TAMB = -40 to +85ºC (unless otherwise specified). T ypical values are at T AMB =

+25ºC. Limits are 100% production tested at TAMB = +25ºC.

Table 4. Electrical Characteristics

Symbol Parameter Conditions Min Typ Max Unit

VIN Input Voltage 2.5 5.5 V

Output V oltage Accuracy TAMB = +25ºC, IOUT = 100µA -1 1 %

TAMB = -40 to +85ºC, IOUT = 100µA to 150mA - 3 3

IOUT Maximum Output Current 150 mA

ILIM Current Limit 160 380 mA

IQGround Pin C urr ent IOUT = 100µA 70 180 µA

IOUT = 150mA 115

VIN -VOUT Dropout Voltage 1

IOUT = 100µA 0.05

IOUT = 50mA 20

IOUT = 100mA 40 100

IOUT = 150mA 60

ΔVLNR Line Regulation

VIN = 2.5V or (VOUT + 0.1) to 4.5V,

IOUT = 1mA -0.2 0 0.2 %/V

VIN = 2.5V or (VOUT + 0.1) to 5.5V,

IOUT = 1mA -0.8 0 0.8

ΔVLDR Load Regulation IOUT = 100µA to 150mA, COUT = 1µF 0.001 0.02 %/mA

en Output Voltage Noise

COUT = 1µF,

f = 10Hz to 100kHz,

CBP = 0.01µF AS1353 30 µVRMS

COUT = 1µF,

f = 10Hz to 100kHz AS1356 110

PSRR Output Voltage AC

Power-Supply Rejection

Ratio f = 100Hz, COUT = 1µF,

(CBP = 0.01µF, AS1353) 60 dB

Shutdown 2

tON Exit Delay from

Shutdown 3,4CBP = 0.01µF, no load

(AS1353) 30 150 µs

IOFF Shutdown Supply

Current SHDNM = GND TAMB = +25ºC 0.01 1 µA

TAMB = +85ºC 0.04

VIH SHDNM Input Threshold VIN = 2.5 to 5.5V 2.0 V

VIL 0.4

ISHDNM SHDNM Input Bias

Current SHDNM = IN or GND TAMB = +25ºC 0.03 100 nA

TAMB = +85ºC 0.2

Power-OK Output (AS1356 o nly)

VPOK Power-OK Voltage

Threshold IOUT = 0, VOUTFALLING 92 95 97 %

VOUT

Hysteresis, IOUT = 0 1

VOL POK Output Voltage Low ISINK = 1mA 0.4 V

POK Output Leakage

Current 0 ≤ VPOK ≤ 5.5V, VOUT in regulation 1 µA

Thermal Protection

TSHDNM Thermal Shutdown

Temperature AS1353 150 ºC

AS1356 165

ΔTSHDNM Thermal Shutdown

Hysteresis AS1353 15 ºC

AS1356 20 ºC

www.austriamicrosystems.com Revision 1.03 5 - 13

AS1353/AS1356

Data Sheet - Electrical Characteristics

1. Dropout voltage = VIN - VOUT when VOUT is 100mV < VOUT for VIN = VOUT +0.5V (applies only to output volt ages

≥ 2.5V).

2. The rise and fall time of the shutdown signal must not exceed 1ms.

3. The delay time is defined as time required to set VOUT to 95% of its final value.

4. Guaranteed by design.

www.austriamicrosystems.com Revision 1.03 6 - 13

AS1353/AS1356

Data Sheet - Typical Operating Characteristics

7 Typical Operating Characteristics

VOUT = +3.0V, VIN = +3.6V, CIN = COUT = 1µF, SHDNM = IN, TAMB = +25ºC (unless otherwise specified)

Figure 3. Ground Pin Current vs. Input Voltage Figure 4. Ground Pin Current vs. Output Load

Figure 5. Ground Pin Current vs. Temperature Figure 6. Output Vol tage vs. Input Voltage

Figure 7. Output Voltage vs. Output Load Figure 8. Output Voltage vs. Temperature

100

120

140

0123456

Input Voltage (V)

Ground P in Cur r ent ( µA) .

100

110

120

0 25 50 75 100 125 150

Out put Load (mA)

Ground P in Cur r ent ( µA) .

IOUT = 0mA

IOUT = 150mA

VIN = 3.5V

VIN = 5V

100

110

120

130

-40-200 20406080100

Temper atur e ( °C)

Ground P in Cur r ent ( µA) .

VIN = 3.6V , IOUT = 150mA

VIN = 5V, IOUT = 150mA

VIN = 3.6V, IOUT = 0mA

VIN = 5V, IOUT = 0mA 0

0.5

1.5

2.5

3.5

0123456

I nput Voltage (V)

Out put V oltage (V ) .

IOUT = 0mA

IOUT = 150mA

2.9

2.95

3.05

3.1

0 25 50 75 100 125 150

O utput Load ( mA)

Out put V oltage (V ) .

VIN = 5V

VIN = 3.6V

2.98

2.99

3.01

3.02

3.03

3.04

-40 -20 0 20 40 60 80 100

T emperature ( ° C)

Out put V oltage (V ) .

VIN = 5V, IOUT = 150mA

VIN = 3.6V, IOUT = 0mA

VIN = 3.6V , IOUT = 0mA

VIN = 3.6V,

IOUT = 150mA

www.austriamicrosystems.com Revision 1.03 7 - 13

AS1353/AS1356

Data Sheet - Typical Operating Characteristics

Figure 9. Dropout Voltage vs. Output Load Figure 10. PSRR vs. Frequency

Figure 11. Line Transient Response; IOUT = 50mA

100

125

150

0 25 50 75 100 125 150

Out put Load (mA)

Dropout V oltage (V) .

-45°C

+85°C

+25°C

10 100 1000 10000 100000

F requency (Hz)

PSRR (dB ) .

10ms/Div

VIN

20mV/Div 4V 5V

VOUT

www.austriamicrosystems.com Revision 1.03 8 - 13

AS1353/AS1356

Data Sheet - Detailed Description

8 Detailed Description

The AS1353/AS1356 are low-dropout, low-quiescent-current linear regulators intended for LDO regulator applications

where output current load requirements range from no load to 150mA. All devices come standard with fixed output volt-

ages of 1.5 to 3.6V (see Ordering Information on page 12).

Figure 12. Block Diagram

As illustrated in Figure 12, the devices comprise a 1.25V reference, error amplifier, P-channel MOSFET pass transis-

tor, power-OK comparator, internal feedback voltage divider , current limiter, reverse-battery protection, thermal sensor

and shutdown logic.

The 1.25V bandgap refe rence is connected to the inverting inp ut of the error amplifier. The error amplifier compares

this reference with the feedback voltage and amplifies the difference. If the feedback voltage is lower than the refer-

ence voltage, the P-channel MOSFET gate is pulled lower, allowing more current to pass to the output, and increases

the output voltage. If the feedback voltage is too high, the pass-transistor gate is pulled up, allowing less current to

pass to the output. The output voltage feeds back through an internal resistor voltage divider connected to pin OUT.

Output Voltages

Standard products are factory-set with output voltages of from 1.5 to 3.6V. A two-digit suffix of the part number identi-

fies the nominal output voltage (see Ordering Information on page 12).

Non-standard devices are available. Contact austriamicrosystems AG for more information.

Internal P-Channel MOSFET Pass Transistor

The integrated 0.5Ω (typ) P-channel MOSFET pass transistor requires no base drive, which reduces quiescent current

significantly, and does not exhibit the problems associated with PNP-based regulators, such as dropout when the pass

transistor saturates or high base-drive currents under large load conditions.

The devices consume only 115µA quiescent current in dropout, light-load, or heavy-load applications (see Typical

Operating Characteristics on page 6).

Power-OK

The AS1356’s power-ok circuitry is built around an N-channel MOSFET. The circuitry monitors th e voltage on pin 5

(OUT) and if the voltage goes out of regulation (e.g. during dropout, current limit, or thermal shutdown) pin POK goes

low.

SHDNM

AS1353/AS1356

–

GND

Reverse-

Battery

Protection

OUT

POK 2

Error

Amplifier

Thermal

Overload

Protection

Bandgap Voltage

Current Reference

95%

Shutdown/

Power-On

Control Logic

Trimmable

Reference

Voltage

BP 1

1 AS1353 only

2 AS1356 only

AS1356 only

www.austriamicrosystems.com Revision 1.03 9 - 13

AS1353/AS1356

Data Sheet - Detailed Description

The power-OK feature is not active during shutdown and pr ovides a power-on-reset (POR) function that can operate

down to VIN = 1V. A capacitor to GND may be added to generate a POR delay.

To obtain a logic-level output, conne ct a pull-up resistor from pin POK to pin OUT. Larger values for this resistor will

help minimize current consumption; a 100kΩ resistor is perfect for most applications (see Figure 13).

Reverse-Battery Protection

The AS1353/AS1356 contain integrated reverse-battery protection circuitry which monitors the polarity of pins IN and

SHDNM and disconnects the internal circuitry and parasitic diodes if the battery is connected incorrectly. Reverse sup-

ply current is limited to 1mA if VIN = VSHDNM falls below ground. Load current is also limited when VIN or VSHDNM are

reverse biased with respect to ground.

Current Limiting

The AS1353/AS1356 include current limiting circuitry to protect against short-circuit conditions. The circuitry monitors

and controls the gate voltage of the P-channel MOSFET, limiting the output current to 380mA (typ). The P-channel

MOSFET output can be shorted to ground for an indefinite period of time without damaging the device.

Noise Reduction

The AS1353 uses an external 0.01µF bypass capacitor (CBP) at pin BP to reduce output noise. An internal pre-charge

circuit is used to reduce start-up time.

The use of CBP > 0.01µF improves noise performances but increases start-up time.

Thermal-Overload Protection

The devices are protected against thermal runaway conditions by the integrated thermal sensor circuitry. Thermal

shutdown is an effective means to prevent die overheating since the power transistor is the principle heat source in the

device.

If the junction temperature excee ds 165ºC (typ, AS1356) or 150ºC (typ, AS1353), the thermal sensor starts the shut-

down logic, at which point the P-channel MOSFET is switched off. After the device temperature has dropped by

approximately 20ºC, the thermal sensor will turn the P-channel MOSFET on again. Note that this will be exhibited as a

pulsed output under continu ous thermal-overload conditions.

Note: The absolute maximum junction-temperature rating of +150ºC should not be exceedin g during continual oper-

ation.

Operating Region and Power Dissipation

Maximum power dissipation is determined by the thermal resistance of the case and circuit board, the temperature dif-

ference between the die junction and ambient air, and the rate of air flow. Th e power dissipation of the device is calcu-

lated by:

P = IOUT (VIN - VOUT)(EQ 1)

Maximum power dissipation is calculated by:

PMAX = (TJ - TAMB) / (

JB +

JA)(EQ 2)

Where:

TJ - TAMB is the temperature difference between the device die junction and the surround ing air.

JB or

JC is the thermal resistance of the package.

JA is the thermal resistance through the printed circuit board, copper traces, and other materials to the surrounding

air.

Note: Pin GND is a multi-function pin providing a connection to the system ground and acting as a heat sink. This pin

should be connected to the system ground using a large pad or ground plane.

www.austriamicrosystems.com Revision 1.03 10 - 13

AS1353/AS1356

Data Sheet - Typic al Application

9 Typical Application

Figure 13. Typical Application Diagrams

Capacitor Selection and Regulator Stability

Ceramic capacitors are highly recommended as they offer distinct advantages over their tantalum and aluminum elec -

trolytic components.

For stable operation with load currents up to 150mA over the entire device temperature range, use a 1µF (min)

ceramic output capacitor with an ESR <0.2 Ω.

Use large output capacitor values (10µF max) to reduce noise and improve load transient-response, stability and

power-supply rejection.

Note: Some ceramic capacitors exhibit large capacitance and ESR variations with variations in temperature. Z5U

and Y5V capacitors may be required to ensure stability at temperatures below TAMB = -10ºC. With X7R or X5R

capacitors, a 1µF capacitor should be sufficient at all operating temperatures.

Power Supply Rejection Ratio

The AS1353/AS1356 are designed to deliver low dropout voltages and low quiescent currents. Power-supply rejection

is 60dB (typ) at low frequencies. To improve power supply-noise rejection and transient response, increase the values

of the input and output bypass capacitors (see Figure 13).

The Typical Operating Characteristics (page 6) show the device line- and load-transient responses. See the Power-

Supply Rejection Ratio vs. Frequency graph in the Typical Operating Characteristics sectio n (page 6) for further

details.

Dropout Voltage

For standard products with output voltage greater than the minimum VIN (2.5V), the minimum input-output voltage dif-

ferential (dropout voltage) determines the lowest usable supply voltage. This determines the useful end-of-life battery

voltage in battery-powered systems.

The dropout voltage is a function of the P-MOSFET drain-to-source on-resistance multiplied by the load current, and is

calculated by:

VDROPOUT = VIN - VOUT = RDS(ON) x IOUT (EQ 3)

Where:

RDS(ON) is the drain-to-source on-resistance.

IOUT is the supply current.

See Typical Operating Characteristics (page 6) for further information.

AS1356

SHDNM

IN OUT

POK

CIN

1µF

+2.5 to

+5.5V COUT

1µF

100kΩ

Off

Preset Output

1.5 to 3.6V,

150mA

To Micro-

processor

AS1353

CBP

0.01µF

SHDNM

IN OUT

CIN

1µF

+2.5 to

+5.5V COUT

1µF

Off

Preset Output

1.5 to 3.6V,

150mA

GNDGND

www.austriamicrosystems.com Revision 1.03 11 - 13

AS1353/AS1356

Data Sheet - Package Drawings and Markings

10 Package Drawings and Markings

The AS1353/AS1356 are available in a 5-pin SOT23 package.

Figure 14. 5-pin SOT23 Package

Symbol Min Max

A0.901.45

A1 0.00 0.15

A2 0.90 1.30

b0.300.50

C0.090.20

D2.803.05

E2.603.00

E1 1.50 1.75

L0.300.55

e 0.95 REF

e1 1.90 REF

α0º 8º

Notes:

1. All dimensions in millimeters.

2. Foot length measured at intercept point between datum A and lead

surface.

3. Package outline exclusive of mold flas h and metal burr.

4. Package outline inclusive of solder plating.

5. Complies with EIAJ SC74.

6. PKG ST 0003 Rev A supersedes SOT23-D-2005 Rev C.

www.austriamicrosystems.com Revision 1.03 12 - 13

AS1353/AS1356

Data Sheet - Ordering Information

11 Ordering Information

The devices are available as the following standard products.

Non-standard versions are available with a minimum order of 30,000 units. Contact austriamicrosystems for availability

of non-standard versions.

Type Marking Description Delivery Form Package

AS1353-15-T ASD8 LDO 150mA, Reverse-Battery Protection, 1.5V Tape and Reel 5-p in SOT 23

AS1353-18-T ASD9 LDO 150mA, Reverse-Battery Protection, 1.8V Tape and Reel 5-p in SOT 23

AS1353-26-T ASHB LDO 150mA, Reverse-Battery Protection, 2.6V Tape and Reel 5-pin SOT23

AS1353-28-T ASHC LDO 150mA, Reverse-Battery Protection, 2.8V Tape and Reel 5-pin SOT23

AS1353-30-T ASHD LDO 150mA, Reverse-Battery Protection, 3.0V Tape and Reel 5-pin SOT23

AS1353-33-T ASHE LDO 150mA, Reverse-Battery Protection, 3.3V Tape and Reel 5-pin SOT23

AS1353-36-T ASI8 LDO 150mA, Reverse-Battery Protection, 3.6V Tape and Reel 5-pin SOT23

AS1356-27-T ASHM LDO 150mA, Reverse-Battery Protection,with

Power-OK, 2.7V Tape and Reel 5-pin SOT23

AS1356-33-T ASHO LDO 150mA, Reverse-Battery Protection,with

Power-OK, 3.3V Tape and Reel 5-pin SOT23

www.austriamicrosystems.com Revision 1.03 13 - 13

AS1353/AS1356

Data Sheet

Copyrights

lated, stored, or used without the prior written consent of the copyright owner.

All products and companies mentioned are trademarks or registered trademarks of their respective companies.

Disclaimer

Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing

in its Term of Sale. austriamicrosystems A G makes no warranty , express, statutor y , implied, or by description regarding

the information set forth herein or regard i ng th e fre e do m of the described devices from patent infringement. austriami-

crosystems AG reserves the right to change specifications and prices at any time and withou t notice. Therefore, prior

to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information.

This product is intended for use in normal commercial applications. Applicati ons requiring extended temperature

range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-

sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for

each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard

production flow, such as test flow or test location.

The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However,

austriamicrosystems AG shall not be liable to recipien t or any third party for any damages, including but not limited to

personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or

consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the tech-

nical data herein. No obligation or liability to recipient or any third party shall arise or flow out of

austriamicrosystems AG rendering of technical or other services.

Cont act Information

Headquarters

austriamicrosystems AG

A-8141 Schloss Premstaetten, Austria

Tel: +43 (0 ) 3136 500 0

Fax: +43 (0) 3136 525 01

For Sales Offices, Distributors and Representatives, please visit:

http://www.austriamicrosystems.com/contact