PI3USB14 Low Voltage, High Bandwidth, USB 2.0, 4:1 Mux/DeMux with Single Enable Features Description * Near-Zero propagation delay The PI3USB14 is a 2-channel, 4:1 Multiplexer/Demultiplexer with 3-state outputs. The switch introduces no additional ground bounce noise or propagation delay. * 5 switches connect inputs to outputs * High signal passing bandwidth (300MHz) * Beyond Rail-to-Rail switching * 5V I/O tolerant with 3.3V supply * 2.5V and 3.3V supply voltage operation * Hot insertion capable * Industrial operating temperature: -40C to +85C The PI3USB14 device is very useful in switching USB 2.0 signals and others that have high bandwidth (300MHz). * 2KV ESD Protection (human body model) * Latch-up performance >250mA per JESD17 * Packaging (Pb-free & Green available): - 16-pin 150-mil wide plastic QSOP (Q) - 16-pin 173-mil wide plastic TSSOP (L) - 20-contact TQFN (ZH) Block Diagram 18 N.C. IA3 4 17 S0 IA2 5 16 IB3 IA1 6 15 IB2 IA0 7 14 IB1 YA 8 13 IB0 N.C. 9 12 YB VCC EN 2 S1 2 15 N.C. S1 IA3 3 14 S0 IA2 4 13 IB3 IA1 5 12 IB2 IA0 6 11 IB1 YA 7 10 IB0 GND 8 9 YB 10 YB 11 N.C. GND YA 3 16 S1 20 N.C. 1 S0 1 19 EN EN VCC IA0 IA1 IA2 IA3 IB0 IB1 IB2 IB3 N.C. Pin Configuration Notes: 1. N.C. = No internal connection Truth Table(1) Enable Select EN S1 S0 Y Function H X X Hi-Z Disable L L L I0 S1-0 = 0 L L H I1 S1-0 = 1 L H L I2 S1-0 = 2 L H H I3 S1-0 = 3 Pin Description Pin Name Notes: 1. H=High Voltage Level; L=Low Voltage Level 1 Description IAN, IBN Data Inputs S0-1 Select Inputs EN Enable YA to YB Data Outputs GND Ground VCC Power PS8760 02/01/05 PI3USB14 Low Voltage, High Bandwidth, USB 2.0, 4:1 Mux/DeMux with Single Enable Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................................ -65C to +150C Ambient Temperature with Power Applied ............... -40C to +85C Supply Voltage to Ground Potential ........................... -0.5V to +4.6V DC Input Voltage ........................................................ -0.5V to +6.0V DC Output Current................................................................... 120mA Power Dissipation ....................................................................... 0.5W Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics, 3.3V Supply (Over the Operating Range, TA = -40C to +85C, VCC = 3.3V 10%) Parameters Description Test Conditions(1) Typ.(2) Min. Max. Units 0.8 V VIH Input HIGH Voltage Guaranteed Logic HIGH Level VIL Input LOW Voltage Guaranteed Logic LOW Level VIK Clamp Diode Voltage VCC = Min., IIN = -18 mA IIH Input HIGH Current VCC = Max., VIN = VCC 1 IIL Input LOW Current VCC = Max., VIN = GND 1 IOZH High Impedance Output Current 0 Y, In VCC RON Switch On-Resistance(4) 2.0 -1.3 -1.8 A 1 VCC = Min., VIN = 0.0V, ION = 48 mA or -64mA 4 6 VCC = Min., VIN = 3.6V, ION = -15 mA 5 8 DC Electrical Characteristics, 2.5V Supply (Over Operating Range, TA = -40C to +85C, VCC = 2.5V 10%) Parameters(5) Description Test Conditions Min. Typ. Max. VIH Input HIGH Voltage Guaranteed Logic HIGH Level 1.8 VCC + 0.3 VIL Inout LOW Voltage Guaranteed Logic LOW Level -0.3 0.8 VIK Clamp Diode Voltage VCC = Max., IIN = -6mA IIH Input HIGH Current VCC = Max., VIN = VCC 1 IIL Input LOW Current VCC = Max., VIN = GND 1 IOZH High Impedance 0 Y, In VCC 1 RON Current(3) Switch On Resistance(4) -0.7 VCC = Min., VIN = 0.0V, ION = -48mA 6 VCC = Min., VIN = 2.25V, ION = -15mA 7 2 Units V -1.8 A 8 14 PS8760 02/01/05 PI3USB14 Low Voltage, High Bandwidth, USB 2.0, 4:1 Mux/DeMux with Single Enable Capacitance (TA = 25C f = 1 MHz) Parameters(5) Description CIN Input Capacitance COFF(IN) In Capacitance, Switch Off COFF(Y) Y Capacitance, Switch Off CON Y/In Capacitance, Switch On Test Conditions Typ. Units 3.0 3.5 VIN = 0V pF 12 15.0 Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 3.3V, TA = 25C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. Measured by the voltage drop between Y and In pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (Y, In) pins. 5. This parameter is determined by device characterization but is not production tested. Power Supply Characteristics Parameters Description ICC Quiescent Power Supply Current Test Conditions(1) VCC = 3.6V, VIN = GND or VCC Min. Typ.(2) Max. 0.8 Units mA Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at VCC = 3.3V, +25C ambient. 3. Per LVTTL driven input (control inputs only); Y and In pins do not contribute to ICC. This parameter is guaranteed, but not production tested. 3 PS8760 02/01/05 PI3USB14 Low Voltage, High Bandwidth, USB 2.0, 4:1 Mux/DeMux with Single Enable Dynamic Electrical Characteristics Over the Operating Range (TA = -40 to +85, VCC = 3.3V 10%) Parameter Description Test Condition Min. Typ. XTALK Crosstalk See Test Diagram -60 OIRR Off-Isolation See Test Diagram -60 BW -3dB Bandwidth See Test Diagram 200 Max. Units dB 300 MHz Switching Characteristics over 3.3V Operating Range Parameters Conditions(1) Description tPLH tPHL Propogation Delay(2,3) Y to In, In to Y tPZH tPZL Enable Time S or EN to Y or In tPHZ tPLZ Disable Time S or EN to Y or In Com. Min. Typ. Max. See Test Diagram Units 0.3 1.5 9.0 1.5 9.0 ns See Test Diagram Switching Characteristics over 2.5V Operating Range Parameters Conditions(1) Description tPLH tPHL Propogation Delay(2,3) Y to In, In to Y tPZH tPZL Enable Time S or EN to Y or In tPHZ tPLZ Disable Time S or EN to Y or In Com. Min. See Test Diagram Max. Units 0.3 1.5 15.0 1.5 12.0 ns See Test Diagram Notes: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not tested on Propagation Delays. 3. The switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.30ns for 10pF load. Since this time constant is much smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 4 PS8760 02/01/05 PI3USB14 Low Voltage, High Bandwidth, USB 2.0, 4:1 Mux/DeMux with Single Enable Test Circuit for Electrical Characteristics(1) 6.0V VCC 200-ohm Pulse Generator VIN VOUT D.U.T 10pF CL RT 200-ohm Notes: 1. CL = Load capacitance: includes jig and probe capacitance. 2. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator 3. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. 4. All input impulses are supplied by generators having the following characteristics: PRR MHz, ZO = 50, tR 2.5ns, tF 2.5ns. 5. The outputs are measured one at a time with one transition per measurement. Switch Positions Test Switch tPLZ, tPZL 6.0V tPHZ, tPZH GND Prop Delay Open Test Circuit for Dynamic Electrical Characteristics HP4195A S1 VCC R1 T1 D.U.T HP11667A 10pF 5 50-ohm PS8760 02/01/05 PI3USB14 Low Voltage, High Bandwidth, USB 2.0, 4:1 Mux/DeMux with Single Enable Switching Waveforms 2.5V S or EN 1.25V 1.25V 0V 3.5V 2.5V Input tPLH Output Output 2.5V tPHL tPLZ VDD/2 1.5V VOH 2.5V tPZL VOL Output VOL +0.3V VOL tPHZ tPZH 2.5V VOH VOH VDD/2 VOH -0.3V VOL Voltage Waveforms Enable and Disable Times 3.5V 2.5V Input tPLH tPHL 1.5V VOH 2.5V Output VOL tSK(p) = I tPHL - tPLH I Pulse Skew - tSK(p) 6 PS8760 02/01/05 PI3USB14 Low Voltage, High Bandwidth, USB 2.0, 4:1 Mux/DeMux with Single Enable Applications Information Logic Inputs The logic control inputs can be driven upto 3.6Vregardless of the supply voltage. For example, given a +3.3V supply, EN maybe driven LOW to 0V and HIGH to 3.6V. Driving EN Rail-to-Rail(R) minimizes power consumption. Power Supply-Sequencing Proper power supply sequencing is recommended for all CMOS devices. Always apply VCC before applying signals to the input/ output or control pins. Hot Insertion For Datacom and Telecom applications that have ten or more volts passing through the backplane, a high voltage from the power supply may be seen at the device input pins during hot insertion. The PI3CHxx devices have maximum limits of 6V and 120mA for 20ns. If the power is higher or applied for a longer time or repeatedly reaches the maximum limits, the devices can be damaged. Packaging Mechanical: 16-pin QSOP (Q) 16 .008 0.20 MIN. .150 .157 3.81 3.99 Guage Plane .010 0.254 1 0-6 .016 .035 0.41 0.89 Detail A .189 .197 4.80 5.00 .041 1.04 REF .015 x 45 0.38 .008 0.203 REF .053 1.35 .069 1.75 Detail A .008 .012 0.203 0.305 .007 .010 0.178 0.254 0.41 .016 1.27 .050 SEATING PLANE .025 BSC 0.635 .008 .013 0.20 0.33 .228 .244 5.79 6.19 .004 0.101 .010 0.254 X.XX DENOTES DIMENSIONS IN MILLIMETERS X.XX 7 PS8760 02/01/05 PI3USB14 Low Voltage, High Bandwidth, USB 2.0, 4:1 Mux/DeMux with Single Enable Packaging Mechanical: 16-pin TSSOP (L) 16 .169 .177 1 .193 .201 4.9 5.1 4.3 4.5 .004 .008 .047 max. 1.20 0.45 .018 0.75 .030 SEATING PLANE .0256 BSC 0.65 .007 .012 .002 .006 0.09 0.20 .252 BSC 6.4 0.05 0.15 0.19 0.30 Packaging Mechanical: 20-Contact TQFN (ZH) 0.750.05 4.500.10 (S) 3.50 REF. Pin 20 2.050.10 1.50 REF. 3.500.10 3.050.10 Pin 1 C 0.35 0.0-0.05 0.400.10 0.50 TYP. (14X) 0.250.05 0.20 REF. 8 PS8760 02/01/05 PI3USB14 Low Voltage, High Bandwidth, USB 2.0, 4:1 Mux/DeMux with Single Enable Ordering Information Ordering Code PI3USB14Q PI3USB14QE PI3USB14L PI3USB14LE PI3USB14ZHE Packaging Type Q Q L L E Package Description 150-mil, 16-pin QSOP Pb-free & Green, 150-mil, 16-pin QSOP 173-mil, 16-pin TSSOP Pb-free & Green, 173-mil, 16-pin TSSOP PI-free & Green, 20-Contact TQFN Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ Pericom Semiconductor Corporation * 1-800-435-2336 * www.pericom.com 9 PS8760 02/01/05