TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 CURRENT-LIMITED POWER-DISTRIBUTION SWITCHES FEATURES 1 * * * * * * * * * * * 80-m High-Side MOSFET Switch 250 mA Continuous Current Per Channel Independent Thermal and Short-Circuit Protection With Overcurrent Logic Output Operating Range: 2.7-V to 5.5-V CMOS- and TTL-Compatible Enable Inputs 2.5-ms Typical Rise Time Undervoltage Lockout 10 A Maximum Standby Supply Current for Single and Dual (20 A for Triple and Quad) Bidirectional Switch Ambient Temperature Range, 0C to 85C ESD Protection TPS2045A, TPS2055A D PACKAGE (TOP VIEW) GND IN IN EN 8 2 7 3 6 4 OUT OUT OUT OC 5 TPS2047A, TPS2057A D PACKAGE (TOP VIEW) GNDA IN1 EN1 EN2 GNDB IN2 EN3 NC DESCRIPTION The TPS2045A through TPS2048A and TPS2055A through TPS2058A power-distribution switches are intended for applications where heavy capacitive loads and short circuits are likely to be encountered. 1 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 OC1 OUT1 OUT2 OC2 OC3 OUT3 NC NC TPS2046A, TPS2056A D PACKAGE (TOP VIEW) GND IN EN1 EN2 1 8 2 7 3 6 4 5 OC1 OUT1 OUT2 OC2 TPS2048A, TPS2058A D PACKAGE (TOP VIEW) GNDA IN1 EN1 EN2 GNDB IN2 EN3 EN4 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 OC1 OUT1 OUT2 OC2 OC3 OUT3 OUT4 OC4 All enable inputs are active high for the TPS205xA series. NC - No connect These devices incorporate 80-m N-channel MOSFET high-side power switches for power-distribution systems that require multiple power switches in a single package. Each switch is controlled by an independent logic enable input. Gate drive is provided by an internal charge pump designed to control the power-switch rise times and fall times to minimize current surges during switching. The charge pump requires no external components and allows operation from supplies as low as 2.7 V. When the output load exceeds the current-limit threshold or a short is present, these devices limit the output current to a safe level by switching into a constant-current mode, pulling the overcurrent (OCx) logic output low. When continuous heavy overloads and short circuits increase the power dissipation in the switch, causing the junction temperature to rise, a thermal protection circuit shuts off the switch to prevent damage. Recovery from a thermal shutdown is automatic once the device has cooled sufficiently. Internal circuitry ensures the switch remains off until valid input voltage is present. These power-distribution switches are designed to current limit at 0.5 A. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2000-2008, Texas Instruments Incorporated TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. AVAILABLE OPTIONS (1) TA ENABLE RECOMMENDED MAXIMUM CONTINUOUS LOAD CURRENT (A) TYPICAL SHORT-CIRCUIT NUMBER OF CURRENT LIMIT AT 25C SWITCHES (A) Active low Single Active high Active low 0C to 85C Active high Active low Active high Active low Active high (1) (2) 2 Dual 0.25 0.5 Triple Quad PACKAGED DEVICES SOIC (D) (2) TPS2045AD TPS2055AD TPS2046AD TPS2056AD TPS2047AD TPS2057AD TPS2048AD TPS2058AD For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. The D package is available taped and reeled. Add an R suffix to device type (e.g., TPS2045ADR) Submit Documentation Feedback Copyright (c) 2000-2008, Texas Instruments Incorporated Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 FUNCTIONAL BLOCK DIAGRAMS TPS2045A Power Switch CS IN OUT Charge Pump EN Current Limit Driver OC UVLO Thermal Sense GND Current sense Active high for TPS205xA series TPS2046A OC1 Thermal Sense GND EN1 Current Limit Driver Charge Pump CS OUT1 UVLO Power Switch IN CS OUT2 Charge Pump Driver Current Limit OC2 EN2 Thermal Sense Current sense Active high for TPS205xA series Copyright (c) 2000-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A 3 TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 TPS2047A OC1 Thermal Sense GNDA EN1 Current Limit Driver Charge Pump CS OUT1 UVLO Power Switch IN1 OUT2 CS Charge Pump Driver Current Limit OC2 EN2 Thermal Sense Power Switch CS IN2 OUT3 Charge Pump EN3 Driver Current Limit OC3 UVLO GNDB 4 Thermal Sense Current sense Active high for TPS205xA series Submit Documentation Feedback Copyright (c) 2000-2008, Texas Instruments Incorporated Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 OC1 TPS2048A Thermal Sense GNDA EN1 Driver Current Limit Charge Pump CS OUT 1 UVLO Power Switch CS IN1 OUT 2 Charge Pump Driver Current Limit OC2 EN2 Thermal Sense OC3 Thermal Sense GNDB EN3 Driver Current Limit Charge Pump CS OUT3 UVLO Power Switch IN2 CS OUT4 Charge Pump Driver Current Limit OC4 EN4 Thermal Sense Current sense Active high for TPS205xA series Copyright (c) 2000-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A 5 TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 Terminal Functions TPS2045A AND TPS2055A TERMINAL NAME NO. I/O DESCRIPTION TPS2045A TPS2055A 4 - I Enable input. Logic low turns on power switch. EN - 4 I Enable input. Logic high turns on power switch. GND 1 1 I Ground 2, 3 2, 3 I Input voltage 5 5 O Overcurrent. Open drain output active low 6, 7, 8 6, 7, 8 O Power-switch output EN IN OC OUT TPS2046A AND TPS2056A TERMINAL NAME NO. I/O DESCRIPTION TPS2046A TPS2056A EN1 3 - I Enable input. Logic low turns on power switch, IN-OUT1. EN2 4 - I Enable input. Logic low turns on power switch, IN-OUT2. EN1 - 3 I Enable input. Logic high turns on power switch, IN-OUT1. EN2 - 4 I Enable input. Logic high turns on power switch, IN-OUT2. GND 1 1 I Ground IN 2 2 I Input voltage OC1 8 8 O Overcurrent. Open drain output active low, for power switch, IN-OUT1 OC2 5 5 O Overcurrent. Open drain output active low, for power switch, IN-OUT2 OUT1 7 7 O Power-switch output OUT2 6 6 O Power-switch output 6 Submit Documentation Feedback Copyright (c) 2000-2008, Texas Instruments Incorporated Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 Terminal Functions (continued) TPS2047A AND TPS2057A TERMINAL NAME NO. I/O DESCRIPTION TPS2047A TPS2057A EN1 3 - I Enable input, logic low turns on power switch, IN1-OUT1. EN2 4 - I Enable input, logic low turns on power switch, IN1-OUT2. EN3 7 - I Enable input, logic low turns on power switch, IN2-OUT3. EN1 - 3 I Enable input, logic high turns on power switch, IN1-OUT1. EN2 - 4 I Enable input, logic high turns on power switch, IN1-OUT2. EN3 - 7 I Enable input, logic high turns on power switch, IN2-OUT3. GNDA 1 1 GNDB 5 5 IN1 2 2 I Input voltage IN2 6 6 I Input voltage NC 8, 9, 10 8, 9, 10 OC1 16 16 O Overcurrent, open drain output active low, IN1-OUT1 OC2 13 13 O Overcurrent, open drain output active low, IN1-OUT2 OC3 12 12 O Overcurrent, open drain output active low, IN2-OUT3 OUT1 15 15 O Power-switch output, IN1-OUT1 OUT2 14 14 O Power-switch output, IN1-OUT2 OUT3 11 11 O Power-switch output, IN2-OUT3 Ground for IN1 switch and circuitry. Ground for IN2 switch and circuitry. No connection TPS2048A AND TPS2058A TERMINAL NAME NO. I/O DESCRIPTION TPS2048A TPS2058A EN1 3 - I Enable input. logic low turns on power switch, IN1-OUT1. EN2 4 - I Enable input. Logic low turns on power switch, IN1-OUT2. EN3 7 - I Enable input. Logic low turns on power switch, IN2-OUT3. EN4 8 - I Enable input. Logic low turns on power switch, IN2-OUT4. EN1 - 3 I Enable input. Logic high turns on power switch, IN1-OUT1. EN2 - 4 I Enable input. Logic high turns on power switch, IN1-OUT2. EN3 - 7 I Enable input. Logic high turns on power switch, IN2-OUT3. EN4 - 8 I Enable input. Logic high turns on power switch, IN2-OUT4. GNDA 1 1 Ground for IN1 switch and circuitry. GNDB 5 5 Ground for IN2 switch and circuitry. IN1 2 2 I Input voltage IN2 6 6 I Input voltage OC1 16 16 O Overcurrent. Open drain output active low, IN1-OUT1 OC2 13 13 O Overcurrent. Open drain output active low, IN1-OUT2 OC3 12 12 O Overcurrent. Open drain output active low, IN2-OUT3 OC4 9 9 O Overcurrent. Open drain output active low, IN2-OUT4 OUT1 15 15 O Power-switch output, IN1-OUT1 OUT2 14 14 O Power-switch output, IN1-OUT2 OUT3 11 11 O Power-switch output, IN2-OUT3 OUT4 10 10 O Power-switch output, IN2-OUT4 Copyright (c) 2000-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A 7 TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 www.ti.com DETAILED DESCRIPTION POWER SWITCH The power switch is an N-channel MOSFET with a maximum on-state resistance of 135 m (VI(IN) = 5 V). Configured as a high-side switch, the power switch prevents current flow from OUT to IN and IN to OUT when disabled. The power switch supplies a minimum of 250 mA per switch. CHARGE PUMP An internal charge pump supplies power to the driver circuit and provides the necessary voltage to pull the gate of the MOSFET above the source. The charge pump operates from input voltages as low as 2.7 V and requires very little supply current. DRIVER The driver controls the gate voltage of the power switch. To limit large current surges and reduce the associated electromagnetic interference (EMI) produced, the driver incorporates circuitry that controls the rise times and fall times of the output voltage. The rise and fall times are typically in the 2-ms to 4-ms range. ENABLE (ENx, ENx) The logic enable disables the power switch and the bias for the charge pump, driver, and other circuitry to reduce the supply current. The supply current is reduced to less than 10 A on the single and dual devices (20 A on the triple and quad devices) when a logic high is present on ENx (TPS204xA 1) or a logic low is present on ENx (TPS205xA1). A logic zero input on ENx or a logic high on ENx restores bias to the drive and control circuits and turns the power on. The enable input is compatible with both TTL and CMOS logic levels. OVERCURRENT (OCx) The OCx open-drain output is asserted (active low) when an overcurrent or over temperature condition is encountered. The output will remain asserted until the overcurrent or over temperature condition is removed. CURRENT SENSE A sense FET monitors the current supplied to the load. The sense FET measures current more efficiently than conventional resistance methods. When an overload or short circuit is encountered, the current-sense circuitry sends a control signal to the driver. The driver in turn reduces the gate voltage and drives the power FET into its saturation region, which switches the output into a constant-current mode and holds the current constant while varying the voltage on the load. THERMAL SENSE The TPS204xA and TPS205xA implement a dual-threshold thermal trip to allow fully independent operation of the power distribution switches. In an overcurrent or short-circuit condition the junction temperature rises. When the die temperature rises to approximately 140C, the internal thermal sense circuitry checks to determine which power switch is in an overcurrent condition and turns off that switch, thus isolating the fault without interrupting operation of the adjacent power switch. Hysteresis is built into the thermal sense, and after the device has cooled approximately 20 degrees, the switch turns back on. The switch continues to cycle off and on until the fault is removed. The (OCx) open-drain output is asserted (active low) when over temperature or overcurrent occurs. UNDERVOLTAGE LOCKOUT A voltage sense circuit monitors the input voltage. When the input voltage is below approximately 2 V, a control signal turns off the power switch. 8 Submit Documentation Feedback Copyright (c) 2000-2008, Texas Instruments Incorporated Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) UNIT VI(IN) Input voltage range (2) VO(OUT) Output voltage range (2) VI(ENx) or VI(ENx) Input voltage range IO(OUT) Continuous output current 0.3 V to 6 V -0.3 V to VI(IN) + 0.3 V -0.3 V to 6 V internally limited Continuous total power dissipation See Dissipation Rating Table TJ Operating virtual junction temperature range Tstg Storage temperature range 0C to 125C -65C to 150C Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds ESD (1) (2) 260C Human body model MIL-STD-883C Electrostatic discharge protection 2 kV Machine model 0.2 kV Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to GND. DISSIPATION RATING TABLE TA 25C POWER RATING DERATING FACTOR ABOVE TA = 25C TA = 70C POWER RATING TA = 85C POWER RATING D-8 725 mW 5.9 mW/C 464 mW 377 mW D-16 1123 mW 9 mW/C 719 mW 584 mW PACKAGE RECOMMENDED OPERATING CONDITIONS MIN MAX VI(IN) Input voltage 2.7 5.5 V VI(EN) or VI(EN) Input voltage 0 5.5 V IO(OUT) Continuous output current (per switch) 0 250 mA TJ Operating virtual junction temperature 0 125 C Copyright (c) 2000-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A UNIT 9 TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 ELECTRICAL CHARACTERISTICS OVER RECOMMENDED OPERATING JUNCTION TEMPERATURE RANGE VI(IN) = 5.5 V, IO = rated current, VI(EN) = VI(IN)(unless otherwise noted) TEST CONDITIONS (1) PARAMETER Static drain-source on-state resistance, 5-V operation rDS(on) Static drain-source on-state resistance, 3.3-V operation tr tf (1) Rise time, output Fall time, output TPS204xA MIN TPS205xA TYP MAX MIN TYP MAX VI(IN) = 5 V, IO = 0.25 A TJ = 25C, 80 100 80 100 VI(IN) = 5 V, IO = 0.25 A TJ = 85C, 90 120 90 120 VI(IN) = 5 V, IO = 0.25 A TJ = 125C, 100 135 100 135 VI(IN) = 3.3 V, IO = 0.25 A TJ = 25C, 90 125 90 125 VI(IN) = 3.3 V, IO = 0.25 A TJ = 85C, 110 145 110 145 VI(IN) = 3.3 V, IO = 0.25 A TJ = 125C, 120 160 120 160 VI(IN) = 5.5 V, CL = 1 F, TJ = 25C, RL = 20 2.5 2.5 VI(IN) = 2.7 V, CL = 1 F, TJ = 25C, RL = 20 3 3 VI(IN) = 5.5 V, CL = 1 F, TJ = 25C, RL = 20 4.4 4.4 VI(IN) = 2.7 V, CL = 1 F, TJ = 25C, RL = 20 2.5 2.5 UNIT m ms ms Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account separately. ENABLE INPUT ENx OR ENx PARAMETER VIH TEST CONDITIONS 2.7 V VI(IN) 5.5 V high-level input voltage TPS204xA MIN TYP TPS205xA MAX 2 MIN TYP MAX 2 V 4.5 V VI(IN) 5.5 V 0.8 0.8 2.7 V VI(IN) 4.5 V 0.4 0.4 VIL Low-level input voltage II Input current ton Turnon time CL = 100 F, RL = 20 20 20 toff Turnoff time CL = 100 F, RL = 20 40 40 TPS204xA VI(ENx) = 0 V or VI(ENx) = VI(IN) TPS205xA VI(ENx) = VI(IN) or VI(ENx) = 0 V -0.5 UNIT 0.5 -0.5 0.5 V A ms CURRENT LIMIT TEST CONDITIONS (1) PARAMETER IOS (1) 10 Short-circuit output current VI(IN) = 5 V, OUT connected to GND, Device enabled into short circuit TPS204xA TPS205xA MIN TYP MAX MIN 0.3 0.5 0.7 0.3 TYP MAX 0.5 0.7 UNIT A Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account separately. Submit Documentation Feedback Copyright (c) 2000-2008, Texas Instruments Incorporated Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 SUPPLY CURRENT (TPS2045A, TPS2055A) PARAMETER VI(EN) = VI(IN) Supply current, low-level output No Load on OUT VI(EN) = 0 V VI(EN) = 0 V Supply current, high-level output TPS2045A TEST CONDITIONS No Load on OUT VI(EN) = VI(IN) TYP TJ = 25C MAX 0.025 MIN TYP MAX 10 TJ = 25C 0.025 40C TJ 125C 85 40C TJ 125C 100 85 40C TJ 125C Leakage current VI(EN)= 0 V 40C TJ 125C Reverse leakage current IN = High impedance VI(EN) = 0 V A 110 TJ = 25C 40C TJ 125C 1 10 TJ = 25C VI(EN) = VI(IN) UNIT 1 40C TJ 125C OUT connected to ground VI(EN)= VI(IN) MIN TPS2055A 110 A 100 100 A 100 0.3 TJ = 25C A 0.3 SUPPLY CURRENT (TPS2046A, TPS2056A) PARAMETER TEST CONDITIONS VI(ENx) = VI(IN) Supply current, low-level output No Load on OUT VI(ENx) = 0 V VI(ENx) = 0 V Supply current, high-level output No Load on OUT VI(ENx) = VI(IN) TJ = 25C 0.025 TPS2056A MAX MIN TYP MAX 0.025 1 40C TJ 125C TJ = 25C 40C TJ 125C VI(ENx) = 0 V 40C TJ 125C Reverse leakage current IN = high impedance VI(EN) = 0 V TJ = 25C 110 100 85 40C TJ 125C Leakage current A 10 85 TJ = 25C 40C TJ 125C UNIT 1 10 TJ = 25C VI(ENx) = VI(IN) Copyright (c) 2000-2008, Texas Instruments Incorporated TYP 40C TJ 125C OUT connected to ground VI(EN) = VI(IN) TPS2046A MIN 110 A 100 100 100 0.3 0.3 Submit Documentation Feedback Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A A A 11 TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 SUPPLY CURRENT (TPS2047A, TPS2057A) PARAMETER TEST CONDITIONS TYP No load on OUTx TPS2057A MAX 0.05 MIN TYP MAX 0.05 2 20 TJ = 25C 40C TJ 125C VI(ENx) = 0 V No load on OUTx 160 40C TJ 125C 200 200 160 40C TJ 125C VI(ENx) = VI(INx) 40C TJ 125C Leakage current OUTx connected to ground VI(ENx) = 0 V 40C TJ 125C Reverse leakage current IN = high impedance VI(ENx) = 0 V 200 A 200 200 A 200 0.3 TJ = 25C VI(ENx) = VI(IN) A 20 TJ = 25C TJ = 25C VI(ENx) = VI(INx) UNIT 2 40C TJ 125C VI(ENx) = 0 V Supply current, high-level output MIN TJ = 25C VI(ENx) = VI(INx) Supply current, low-level output TPS2047A A 0.3 SUPPLY CURRENT (TPS2048A, TPS2058A) PARAMETER TEST CONDITIONS TPS2058A MAX 0.05 No Load on OUTx MIN TYP MAX 0.05 2 20 TJ = 25C 40C TJ 125C VI(ENx) = 0 V No Load on OUTx 170 40C TJ 125C 200 220 170 40C TJ 125C VI(ENx) = VI(INx) 40C TJ 125C Leakage current OUTx connected to ground VI(ENx) = 0 V 40C TJ 125C Reverse leakage current IN = high impedance VI(EN) = 0 V 220 A 200 200 A 200 0.3 TJ = 25C VI(EN) = VI(IN) A 20 TJ = 25C TJ = 25C VI(ENx) = VI(INx) UNIT 2 40C TJ 125C VI(ENx) = 0 V Supply current, high-level output TYP TJ = 25C VI(ENx) = VI(INx) Supply current, low-level output TPS2048A MIN A 0.3 UNDERVOLTAGE LOCKOUT PARAMETER TEST CONDITIONS Low-level input voltage Hysteresis TPS204xA MIN TYP MIN TYP MAX 2.5 2 2.5 2 TJ = 25C TPS205xA MAX 100 100 UNIT V mV OVERCURRENT OC PARAMETER TEST CONDITIONS TPS204xA MIN TYP TPS205xA MAX MIN TYP MAX UNIT Sink current (1) VO = 5 V 10 10 Output low voltage IO = 5 V, VOL(OC) 0.5 0.5 V Off-state current (1) VO = 5 V, VO = 3.3 V 1 1 A (1) Specified by design, not production tested. 12 Submit Documentation Feedback mA Copyright (c) 2000-2008, Texas Instruments Incorporated Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 PARAMETER MEASUREMENT INFORMATION OUT RL tf tr CL VO(OUT) 90% 90% 10% 10% TEST CIRCUIT 50% VI(EN) 50% toff ton toff ton 90% VO(OUT) 50% 50% VI(EN) 90% VO(OUT) 10% 10% VOLTAGE WAVEFORMS Figure 1. Test Circuit and Voltage Waveforms VI(EN) VI(EN) (5 V/div) (5 V/div) VI(IN) = 5 V TA = 25C CL = 0.1 F RL = 20 VO(OUT) (2 V/div) 0 1 2 3 4 5 6 7 8 9 VI(IN) = 5 V TA = 25C CL = 0.1 F RL = 20 VO(OUT) (2 V/div) 10 0 2 4 6 8 10 12 14 16 t - Time - ms t - Time - ms Figure 2. Turnon Delay and Rise Time With 0.1-F Load Figure 3. Turnoff Delay and Rise Time With 0.1-F Load Copyright (c) 2000-2008, Texas Instruments Incorporated 18 Submit Documentation Feedback Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A 20 13 TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 PARAMETER MEASUREMENT INFORMATION (continued) VI(EN) VI(EN) (5 V/div) (5 V/div) VI(IN) = 5 V TA = 25C CL = 1 F RL = 20 VO(OUT) (2 V/div) 0 1 2 3 4 5 6 7 8 VI(IN) = 5 V TA = 25C CL = 1 F RL = 20 VO(OUT) (2 V/div) 9 0 10 2 4 6 8 10 12 14 16 18 20 t - Time - ms t - Time - ms Figure 4. Turnon Delay and Rise Time With 1-F Load Figure 5. Turnoff Delay and Fall Time With 1-F Load VI(IN) = 5 V TA = 25C RAMP: 1A/10ms VI(ENx) (5 V/div) VO(OUT) (2 V/div) VI(IN) = 5 V TA = 25C IO(OUTx) (0.2 A/div) IO(OUT) (0.2 A/div) 0 1 2 3 4 5 6 7 8 9 t - Time - ms Figure 6. TPS2055A, Short-Circuit Current, Device Enabled Into Short 14 Submit Documentation Feedback 10 0 10 20 30 40 50 60 70 80 90 100 t - Time - ms Figure 7. TPS2055A, Threshold Trip Current With Ramped Load on Enabled Device Copyright (c) 2000-2008, Texas Instruments Incorporated Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 PARAMETER MEASUREMENT INFORMATION (continued) VI(IN) = 5 V TA = 25C RAMP: 1A/100 ms VI(EN) (5 V/div) VO(OC) (5 V/div) 220 F 100 F 47 F IO(OUT) IO(OUT) (0.2 A/div) (0.2 A/div) 0 20 40 60 VI(IN) = 5 V TA = 25C RL = 20 80 100 120 140 160 180 200 0 2 4 t - Time - ms 6 8 10 12 VI(IN) = 5 V TA = 25C VO(OC) VO(OC) (5 V/div) (5 V/div) IO(OUT) IO(OUT) (0.5 A/div) (1 A/div) 400 18 20 Figure 9. Inrush Current With 47-F, 100-F and 220-F Load Capacitance VI(IN) = 5 V TA = 25C 200 16 t - Time - ms Figure 8. OC Response With Ramped Load on Enabled Device 0 14 600 800 t - Time - s Figure 10. 4- Load Connected to Enabled Device Copyright (c) 2000-2008, Texas Instruments Incorporated 1000 0 200 400 600 800 1000 t - Time - s Figure 11. 1- Load Connected to Enabled Device Submit Documentation Feedback Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A 15 TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 TYPICAL CHARACTERISTICS TURNON DELAY TIME vs INPUT VOLTAGE TURNOFF DELAY TIME vs INPUT VOLTAGE 10 3.9 Turnon Delay Time - ms 3.6 Turnon Delay Time - ms CL = 1 F RL = 20 TA = 25C CL = 1 F RL = 20 TA = 25C 3.3 3 8 6 4 2.7 2.4 2.5 3 3.5 4 4.5 5 5.5 2 2.5 6 3 VI - Input Voltage - V 3.5 4 4.5 5 VI - Input Voltage - V Figure 12. Figure 13. RISE TIME vs INPUT VOLTAGE FALL TIME vs INPUT VOLTAGE 2.7 1.9 CL = 1 F RL = 20 TA = 25C 2.6 1.8 5.5 6 5.5 6 CL = 1 F RL = 20 TA = 25C f t - Fall Time - ms r t - Rise Time - ms 2.5 2.4 2.3 1.7 1.6 1.5 2.2 1.4 2.1 2 2.5 3 3.5 4 4.5 5 VI - Input Voltage - V Figure 14. 16 Submit Documentation Feedback 5.5 6 1.3 2.5 3 3.5 4 4.5 5 VI - Input Voltage - V Figure 15. Copyright (c) 2000-2008, Texas Instruments Incorporated Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 TYPICAL CHARACTERISTICS (continued) SUPPLY CURRENT, OUTPUT ENABLED vs JUNCTION TEMPERATURE SUPPLY CURRENT, OUTPUT DISABLED vs JUNCTION TEMPERATURE 160 I I(IN) - Supply Current, Output Disabled - nA I I(IN) - Supply Current, Output Enabled - A 100 90 VI(IN) = 5.5 V VI(IN) = 5 V 80 VI(IN) = 4.5 V 70 VI(IN) = 2.7 V 60 VI(IN) = 3.3 V 50 40 -40 0 25 85 TJ - Junction Temperature - C 140 VI(IN) = 5.5 V 120 VI(IN) = 5 V 100 VI(IN) = 4.5 V 80 VI(IN) = 2.7 V 40 20 0 -40 125 VI(IN) = 3.3 V 60 0 25 STATIC DRAIN-SOURCE ON-STATE RESISTANCE vs JUNCTION TEMPERATURE 160 VI(IN) = 2.7 V VI(IN) = 3.3 V 120 VI(IN) = 3 V 100 80 VI(IN) = 5 V 60 VI(IN) = 4.5 V 40 20 0 0 25 125 Figure 17. 85 TJ - Junction Temperature - C Figure 18. Copyright (c) 2000-2008, Texas Instruments Incorporated 125 INPUT-TO-OUTPUT VOLTAGE vs LOAD CURRENT 70 VI(IN) - VO(OUT) - Input-to-Output Voltage - mV r DS(on) - Static Drain-Source On-State Resistance - m Figure 16. 140 85 TJ - Junction Temperature - C TA = 25C VI(IN) = 2.7 V 60 VI(IN) = 4.5 V 50 VI(IN) = 3.3 V 40 VI(IN) = 5 V 30 20 10 0 100 200 300 400 500 IL - Load Current - A Figure 19. Submit Documentation Feedback Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A 17 TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 TYPICAL CHARACTERISTICS (continued) SHORT-CIRCUIT OUTPUT CURRENT vs JUNCTION TEMPERATURE THRESHOLD TRIP CURRENT vs INPUT VOLTAGE 0.67 TA = 25C Load Ramp = 1 A/10 ms 490 VI(IN) = 2.7 V 0.65 480 VI(IN) = 3.3 V Threshold Trip Current - A I OS - Short-Circuit Output Current - mA 500 470 460 VI(IN) = 5 .5V 450 VI(IN) = 4 .5V VI(IN) = 5V 440 430 420 0.63 0.61 0.59 410 0.57 2.5 400 -40 0 25 85 TJ - Junction Temperature - C 125 3 3.5 4 4.5 5 VI - Input Voltage - V Figure 20. Figure 21. UNDERVOLTAGE LOCKOUT vs JUNCTION TEMPERATURE CURRENT-LIMIT RESPONSE vs PEAK CURRENT 2.36 5.5 6 300 Start Threshold 250 2.32 Current-Limit Response - s UVLO - Undervoltage Lockout - V 2.34 2.3 2.28 2.26 2.24 Stop Threshold 2.22 2.2 200 150 100 50 2.18 2.16 -40 0 0 25 85 TJ - Junction Temperature - C Figure 22. 18 Submit Documentation Feedback 125 0 2 4 6 Peak Current - A 8 10 Figure 23. Copyright (c) 2000-2008, Texas Instruments Incorporated Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 APPLICATION INFORMATION TPS2045A 2,3 Power Supply 2.7 V to 5.5 V IN 0.1 F OUT 6,7,8 Load 0.1 F 5 4 22 F OC EN GND 1 Figure 24. Typical Application (Example, TPS2045A) POWER-SUPPLY CONSIDERATIONS A 0.01-F to 0.1-F ceramic bypass capacitor between INx and GND, close to the device, is recommended. Placing a high-value electrolytic capacitor on the output pin(s) is recommended when the output load is heavy. This precaution reduces power-supply transients that may cause ringing on the input. Additionally, bypassing the output with a 0.01-F to 0.1-F ceramic capacitor improves the immunity of the device to short-circuit transients. OVERCURRENT A sense FET is employed to check for overcurrent conditions. Unlike current-sense resistors, sense FETs do not increase the series resistance of the current path. When an overcurrent condition is detected, the device maintains a constant output current and reduces the output voltage accordingly. Complete shutdown occurs only if the fault is present long enough to activate thermal limiting. Three possible overload conditions can occur. In the first condition, the output has been shorted before the device is enabled or before VI(IN) has been applied (see Figure 6). The TPS204xA and TPS205xA sense the short and immediately switch into a constant-current output. In the second condition, a short or an overload occurs while the device is enabled. At the instant the overload occurs, very high currents may flow for a short time before the current-limit circuit can react. After the current-limit circuit has tripped (reached the overcurrent trip threshold) the device switches into constant-current mode. In the third condition, the load has been gradually increased beyond the recommended operating current. The current is permitted to rise until the current-limit threshold is reached or until the thermal limit of the device is exceeded (see Figure 7). The TPS204xA and TPS205xA are capable of delivering current up to the current-limit threshold without damaging the device. Once the threshold has been reached, the device switches into its constant-current mode. OC RESPONSE The OC open-drain output is asserted (active low) when an overcurrent or over temperature condition is encountered. The output will remain asserted until the overcurrent or over temperature condition is removed. Connecting a heavy capacitive load to an enabled device can cause momentary false overcurrent reporting from the inrush current flowing through the device, charging the downstream capacitor. The TPS204xA and TPS205xA family of devices are designed to reduce false overcurrent reporting. An internal overcurrent transient filter eliminates the need for external components to remove unwanted pulses. Using low-ESR electrolytic capacitors on the output lowers the inrush current flow through the device during hot-plug events by providing a low-impedance energy source, also reducing erroneous overcurrent reporting. Copyright (c) 2000-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A 19 TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 TPS2045A GND OUT IN OUT IN OUT EN OC V+ Rpullup Figure 25. Typical Circuit for OC Pin (Example, TPS2045A) POWER DISSIPATION AND JUNCTION TEMPERATURE The low on-resistance on the n-channel MOSFET allows small surface-mount packages, such as SOIC, to pass large currents. The thermal resistance of these packages is high compared to those of power packages; it is good design practice to check power dissipation and junction temperature. Begin by determining the rDS(on) of the N-channel MOSFET relative to the input voltage and operating temperature. As an initial estimate, use the highest operating ambient temperature of interest and read rDS(on) from Figure 18. Using this value, the power dissipation per switch can be calculated by: P +r I2 D DS(on) Depending on which device is being used, multiply this number by the number of switches being used. This step will render the total power dissipation from the N-channel MOSFETs. Finally, calculate the junction temperature: T +P R )T J D qJA A Where: TA = Ambient temperature C RJA = Thermal resistance SOIC = 172C/W (for 8 pin), 111C/W (for 16 pin) PD = Total power dissipation based on number of switches being used. Compare the calculated junction temperature with the initial estimate. If they do not agree within a few degrees, repeat the calculation, using the calculated value as the new estimate. Two or three iterations are generally sufficient to get a reasonable answer. THERMAL PROTECTION Thermal protection prevents damage to the IC when heavy-overload or short-circuit faults are present for extended periods of time. The faults force the TPS204xA and TPS205xA into constant-current mode, which causes the voltage across the high-side switch to increase; under short-circuit conditions, the voltage across the switch is equal to the input voltage. The increased dissipation causes the junction temperature to rise to high levels. The protection circuit senses the junction temperature of the switch and shuts it off. Hysteresis is built into the thermal sense circuit, and after the device has cooled approximately 20 degrees, the switch turns back on. The switch continues to cycle in this manner until the load fault or input power is removed. The TPS204xA and TPS205xA implement a dual thermal trip to allow fully independent operation of the power distribution switches. In an overcurrent or short-circuit condition the junction temperature will rise. Once the die temperature rises to approximately 140C, the internal thermal sense circuitry checks which power switch is in an overcurrent condition and turns that power switch off, thus isolating the fault without interrupting operation of the adjacent power switch. Should the die temperature exceed the first thermal trip point of 140C and reach 160C, both switches turn off. The OC open-drain output is asserted (active low) when overtemperature or overcurrent occurs. UNDERVOLTAGE LOCKOUT (UVLO) An undervoltage lockout ensures that the power switch is in the off state at power up. Whenever the input voltage falls below approximately 2 V, the power switch will be quickly turned off. This facilitates the design of hot-insertion systems where it is not possible to turn off the power switch before input power is removed. The UVLO will also keep the switch from being turned on until the power supply has reached at least 2 V, even if the switch is enabled. Upon reinsertion, the power switch will be turned on, with a controlled rise time to reduce EMI and voltage overshoots. 20 Submit Documentation Feedback Copyright (c) 2000-2008, Texas Instruments Incorporated Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 UNIVERSAL SERIAL BUS (USB) APPLICATIONS The universal serial bus (USB) interface is a 12-Mb/s, or 1.5-Mb/s, multiplexed serial bus designed for low-to-medium bandwidth PC peripherals (e.g., keyboards, printers, scanners, and mice). The four-wire USB interface is conceived for dynamic attach-detach (hot plug-unplug) of peripherals. Two lines are provided for differential data, and two lines are provided for 5-V power distribution. USB data is a 3.3-V level signal, but power is distributed at 5 V to allow for voltage drops in cases where power is distributed through more than one hub across long cables. Each function must provide its own regulated 3.3 V from the 5-V input or its own internal power supply. The USB specification defines the following five classes of devices, each differentiated by power-consumption requirements: * Hosts/self-powered hubs (SPH) * Bus-powered hubs (BPH) * Low-power, bus-powered functions * High-power, bus-powered functions * Self-powered functions Self-powered and bus-powered hubs distribute data and power to downstream functions. The TPS204xA and TPS205xA can provide power-distribution solutions for many of these classes of devices. HOST/SELF-POWERED AND BUS-POWERED HUBS Hosts and self-powered hubs have a local power supply that powers the embedded functions and the downstream ports. This power supply must provide from 5.25 V to 4.75 V to the board side of the downstream connection under full-load and no-load conditions. Hosts and SPHs are required to have current-limit protection and must report overcurrent conditions to the USB controller. Typical SPHs are desktop PCs, monitors, printers, and stand-alone hubs. Bus-powered hubs obtain all power from upstream ports and often contain an embedded function. The hubs are required to power up with less than one unit load. The BPH usually has one embedded function, and power is always available to the controller of the hub. If the embedded function and hub require more than 100 mA on power up, the power to the embedded function may need to be kept off until enumeration is completed. This can be accomplished by removing power or by shutting off the clock to the embedded function. Power switching the embedded function is not necessary if the aggregate power draw for the function and controller is less than one unit load. The total current drawn by the bus-powered device is the sum of the current to the controller, the embedded function, and the downstream ports, and it is limited to 500 mA from an upstream port. LOW-POWER BUS-POWERED FUNCTIONS AND HIGH-POWER BUS-POWERED FUNCTIONS Both low-power and high-power bus-powered functions obtain all power from upstream ports; low-power functions always draw less than 100 mA (see Figure 26); high-power functions must draw less than 100 mA at power up and can draw up to 500 mA after enumeration. If the load of the function is more than the parallel combination of 44 and 10 F at power up, the device must implement inrush current limiting. Power Supply D+ 3.3 V TPS2045A D- VBUS GND 2,3 10 F 0.1 F IN OUT 6, 7, 8 0.1 F 5 USB Control 4 10 F Internal Function OC EN GND 1 Figure 26. Low-Power Bus-Powered Function (Example, TPS2045A) Copyright (c) 2000-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A 21 TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 www.ti.com USB POWER-DISTRIBUTION REQUIREMENTS USB can be implemented in several ways, and, regardless of the type of USB device being developed, several power-distribution features must be implemented. * Hosts/self-powered hubs must: - Current-limit downstream ports - Report overcurrent conditions on USB VBUS - Enable/disable power to downstream ports - Power up at <100 mA - Limit inrush current (<44 and 10 F) - Limit inrush currents - Power up at <100 mA * Bus-powered hubs must: - Enable/disable power to downstream ports - Power up at <100 mA - Limit inrush current (<44 and 10 F) - Limit inrush currents - Power up at <100 mA * Functions must: - Limit inrush currents - Power up at <100 mA The feature set of the TPS204xA and TPS205xA allows them to meet each of these requirements. The integrated current-limiting and overcurrent reporting is required by hosts and self-powered hubs. The logic-level enable and controlled rise times meet the need of both input and output ports on bus-power hubs, as well as the input ports for bus-power functions. 22 Submit Documentation Feedback Copyright (c) 2000-2008, Texas Instruments Incorporated Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 TUSB2040 Hub Controller SN75240 Upstream Port BUSPWR A C B D D+ D- DP0 GANGE D DP1 DM0 DM1 Downstream Ports D+ Ferrite Beads A C B D GND D- GND SN75240 DP2 DM2 5V 33 F DP3 5V DM3 D+ A C B D TPS76333 0.1 F 4.7 F D- SN75240 Ferrite Beads GND DP4 IN 3.3 V 4.7 F VCC DM4 5V TPS2045A GND GND PWRON1 EN OVRCUR1 OC IN 0.1 F 33 F OUT D+ TPS2045A 48-MHz Crystal XTAL1 PWRON2 EN OVRCUR2 OC D- IN Ferrite Beads 0.1 F GND OUT Tuning Circuit 5V XTAL2 OCSOFF TPS2045A PWRON3 EN OVRCUR3 OC IN 0.1 F 33 F OUT D+ GND TPS2045A PWRON4 EN OVRCUR4 OC Ferrite Beads IN D- GND 0.1 F OUT 5V 33 F USB rev 1.1 requires 120 F per hub. Figure 27. Bus-Powered Hub Implementation, TPS2045A Copyright (c) 2000-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A 23 TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 TUSB2040 Hub Controller SN75240 Upstream Port BUSPWR A C B D D+ D- DP0 GANGE D DP1 DM0 DM1 Downstream Ports D+ A C B D GND Ferrite Beads GND SN75240 DP2 DM2 D- 5V 33 F DP3 5V DM3 A C B D TPS76333 0.1 F 4.7 F SN75240 D+ D- Ferrite Beads GND DP4 IN 3.3 V 4.7 F VCC DM4 5V TPS2046A GND GND 48-MHz Crystal PWRON1 EN1 OUT1 OVRCUR1 OC1 OUT2 PWRON2 EN2 OVRCUR2 OC2 33 F D+ IN 0.1 F XTAL1 D- Ferrite Beads GND TPS2046A Tuning Circuit XTAL2 OCSOFF GND PWRON3 EN1 OUT1 OVRCUR3 OC1 OUT2 PWRON4 EN2 OVRCUR4 OC2 5V 33 F IN D+ 0.1 F Ferrite Beads D- GND 5V 33 F USB rev 1.1 requires 120 F per hub. Figure 28. Bus-Powered Hub Implementation, TPS2046A 24 Submit Documentation Feedback Copyright (c) 2000-2008, Texas Instruments Incorporated Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 TUSB2040 Hub Controller 1/2 SN75240 Upstream Port BUSPWR A C B D D+ D- DP0 GANGE D DP1 DM0 DM1 Downstream Ports D+ A C B D GND Ferrite Beads GND SN75240 DP2 DM2 D- 5V 47 F DP3 5V DM3 A C B D TPS76333 0.1 F 4.7 F 1/2 SN75240 D+ D- Ferrite Beads GND DP4 IN 3.3 V 4.7 F VCC DM4 5V TPS2047A GND GND 48-MHz Crystal XTAL1 Tuning Circuit XTAL2 PWRON1 EN1 OUT1 OVRCUR1 OC1 OUT2 PWRON2 EN2 OVRCUR2 OC2 47 F D+ IN1 0.1 F D- Ferrite Beads GND PWRON3 OVRCUR3 5V EN3 OUT3 OC3 47 F OCSOFF IN2 0.1 F GND GNDA GNDB USB rev 1.1 requires 120 F per hub. Figure 29. Bus-Powered Hub Implementation, TPS2047A Copyright (c) 2000-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A 25 TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 TUSB2040 Hub Controller SN75240 Upstream Port BUSPWR A C B D D+ D- DP0 GANGE D DP1 DM0 DM1 Downstream Ports D+ A C B D GND DM2 D- GND SN75240 DP2 TPS2041A Ferrite Beads 5V 33 F DP3 5V DM3 A C B D TPS76333 0.1 F 4.7 F SN75240 D+ D- Ferrite Beads GND DP4 IN 3.3 V 4.7 F VCC DM4 5V TPS2048A GND GND 48-MHz Crystal XTAL1 Tuning Circuit XTAL2 PWRON1 EN1 OUT1 OVRCUR1 OC1 OUT2 PWRON2 EN2 OVRCUR2 OC2 33 F D+ IN1 0.1 F D- Ferrite Beads GND OCSOFF PWRON3 EN3 OUT3 OVRCUR3 OC3 OUT4 PWRON4 EN4 OVRCUR4 OC4 5V 33 F IN2 D+ 0.1 F GND Ferrite Beads GNDA D- GND GNDB 5V 33 F USB rev 1.1 requires 120 F per hub. Figure 30. Bus-Powered Hub Implementation, TPS2048A 26 Submit Documentation Feedback Copyright (c) 2000-2008, Texas Instruments Incorporated Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A TPS2045A,, TPS2046A TPS2047A, TPS2048A, TPS2055A TPS2056A, TPS2057A, TPS2058A www.ti.com SLVS251C - SEPTEMBER 2000 - REVISED JANUARY 2008 GENERIC HOT-PLUG APPLICATIONS (see Figure 31) In many applications it may be necessary to remove modules or pc boards while the main unit is still operating. These are considered hot-plug applications. Such implementations require the control of current surges seen by the main power supply and the card being inserted. The most effective way to control these surges is to limit and slowly ramp the current and voltage being applied to the card, similar to the way in which a power supply normally turns on. Due to the controlled rise times and fall times of the TPS204xA and TPS205xA, these devices can be used to provide a softer start-up to devices being hot-plugged into a powered system. The UVLO feature of the TPS204xA and TPS205xA also ensures the switch will be off after the card has been removed, and the switch will be off during the next insertion. The UVLO feature insures a soft start with a controlled rise time for every insertion of the card or module. PC Board TPS2045A Power Supply 2.7 V to 5.5 V 1000 F Optimum 0.1 F GND OUT IN OUT IN OUT EN OC Block of Circuitry Overcurrent Response Figure 31. Typical Hot-Plug Implementation (Example, TPS2045A) By placing the TPS204xA and TPS205xA between the VCC input and the rest of the circuitry, the input power will reach these devices first after insertion. The typical rise time of the switch is approximately 2.5 ms, providing a slow voltage ramp at the output of the device. This implementation controls system surge currents and provides a hot-plugging mechanism for any device. Copyright (c) 2000-2008, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS2045A TPS2046A TPS2047A TPS2048A TPS2055A TPS2056A TPS2057A TPS2058A 27 PACKAGE OPTION ADDENDUM www.ti.com 20-Aug-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp TPS2045AD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2045ADG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2045ADR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2045ADRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2046AD NRND SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2046ADG4 NRND SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2046ADR NRND SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2046ADRG4 NRND SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2047ADR NRND SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2047ADRG4 NRND SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2048AD ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2048ADG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2048ADR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2048ADRG4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2055AD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2055ADG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2055ADR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 (3) Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 20-Aug-2011 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp TPS2055ADRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2056AD NRND SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2056ADG4 NRND SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2056ADR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2056ADRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2057AD ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2057ADG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2057ADR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2057ADRG4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2058AD ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2058ADG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 20-Aug-2011 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing TPS2045ADR SOIC D TPS2046ADR SOIC TPS2047ADR SOIC TPS2048ADR SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 5.2 2.1 8.0 12.0 Q1 8 2500 330.0 12.4 6.4 D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 TPS2055ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS2056ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS2056ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS2057ADR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS2045ADR SOIC D 8 2500 340.5 338.1 20.6 TPS2046ADR SOIC D 8 2500 340.5 338.1 20.6 TPS2047ADR SOIC D 16 2500 333.2 345.9 28.6 TPS2048ADR SOIC D 16 2500 333.2 345.9 28.6 TPS2055ADR SOIC D 8 2500 340.5 338.1 20.6 TPS2056ADR SOIC D 8 2500 340.5 338.1 20.6 TPS2056ADR SOIC D 8 2500 367.0 367.0 35.0 TPS2057ADR SOIC D 16 2500 333.2 345.9 28.6 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated