TFA9892 12 V boosted audio system with adaptive sound maximizer and speaker protection Rev. 1.0 -- 1 September 2017 Product short data sheet 1. General description The TFA9892 is a high efficiency class-D audio amplifier with a sophisticated speaker boost and protection algorithm. It can deliver 13.2 W peak output power into an 8 speaker at a supply voltage of 4.0 V. The internal boost converter raises the supply voltage to 12 V, providing ample headroom for major improvements in sound quality. A safe working environment is provided for the speaker under all operating conditions. The TFA9892 maximizes acoustic output while ensuring diaphragm displacement and voice coil temperature do not exceed their rated limits. This function is based on a speaker box model that operates in all loudspeaker environments (e.g. free air, closed box or vented box). Furthermore, advanced signal processing ensures the quality of the audio signal is never degraded by unwanted clipping or distortion in the amplifier or speaker. An integrated Multiband Dynamic Range Compressor (MDRC) allows the speaker to operate at the highest possible power rating without suffering physical damage. Unlike competing solutions, the adaptive sound maximizer algorithm uses feedback to accurately calculate both the temperature and the excursion, allowing the TFA9892 to adapt to changes in the acoustic environment. Internal intelligent DC-to-DC conversion boosts the supply rail to provide additional headroom and power output. The supply voltage is only raised when necessary. This maximizes the output power of the class-D audio amplifier while limiting quiescent power consumption in combination with a Pulse Frequency Modulation (PFM) scheme. The device can be configured to drive either a hands-free speaker (4 to 8 ) for audio playback, or a receiver speaker (32 ) for handset playback, allowing it to be embedded in platforms that support either or both options. The maximum output power, gain, and noise levels are lower in the Handset Call use case than in the Hands-free Call use case. The TFA9892 also incorporates advanced battery protection. By limiting the supply current when the battery voltage is low, it prevents the audio system from drawing excessive load currents from the battery, which could cause a system undervoltage. The advanced processor minimizes the impact of a falling battery voltage on the audio quality by preventing distortion as the battery discharges. Because it has a digital input interface, the TFA9892 features low RF susceptibility. The second order closed loop architecture used in a class-D audio amplifier provides excellent audio performance and high supply voltage ripple rejection. The TDM/I2S audio interface provides a wide range of settings for multiple slots and Digital I/O. The settings are communicated via an I2C-bus interface. TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection The device also provides the speaker with robust protection against ESD damage. In a typical application, no additional components are needed to withstand a 15 kV discharge on the speaker. The TFA9892 is available in a 49-bump WLCSP (Wafer Level Chip-Size Package) with a 400 m pitch. 2. Features and benefits Output power: 6.6 W into 8 at 4.0 V supply voltage (THD = 1 %) Wide range of speakers: 4 to 8 for hands-free mode and 16 , 32 for handset one Sophisticated speaker-boost and protection algorithm that maximizes speaker performance while protecting the speaker: Fully embedded software, no additional license fee or porting required Total integrated solution that includes DSP, ClassD amplifier, DC-to-DC converter Adaptive excursion control - guarantees that the speaker membrane excursion never exceeds its rated limit Multiband dynamic range compressor (DRC) allows independent control of up to three frequency bands Real-time temperature protection - direct measurement ensures that voice coil temperature never exceeds its rated limit Environmentally aware - automatically adapts speaker parameters to acoustic and thermal changes including compensation for speaker-box leakage Four TDM/I2S inputs output (I/O) to support two audio sources or one PDM input and inter-chip communications Speaker current and voltage monitoring via TDM for Acoustic Echo Cancellation (AEC) at the host Option to route TDM input direct to TDM output to allow a second TDM output slave device to be used in combination with the TFA9892 Sample frequencies fs from 16 kHz to 48 kHz supported in TDM/I2S mode; speaker-boost and protection algorithm sample rate up to 48 kHz. 3 bit clock/word select ratios supported (32x, 48x, 64x) in TDM/I2S mode I2C-bus control interface (400 kHz) 12 V DC-to-DC converter using PFM mode Wide supply voltage range (fully operational from 2.7 V to 5.5 V) Fully short-circuit proof across the load and to the supply lines Low RF susceptibility Input clock jitter insensitive interface Thermally protected 15 kV system-level ESD protection without external components `Pop noise' free at all mode transitions 3. Applications Mobile phones Tablets TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 2 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection Portable Navigation Devices (PND) Notebooks/Netbooks MP3 players and portable media players Small audio systems 4. Quick reference data Table 1. Quick reference data Symbol Parameter Conditions Min Typ Max Unit VBAT battery supply voltage on pin VBAT 2.7 - 5.5 V VDDD digital supply voltage on pin VDDD 1.65 1.8 1.95 V IBAT battery supply current on pin VBAT and in DC-to-DC converter coil; Operating modes with load; DC-to-DC converter in Adaptive Boost mode (no output signal, VBAT = 3.6 V, VDDD = 1.8 V) - 2.45 - mA Power-down mode - 1 5 A on pin VDDD; Operating mode; no audio stream at the input; DSP enabled; SpeakerBoost activated - 20 - mA Operating mode; no audio content; DSP bypassed - 4.5 - mA on pin VDDD; Power-down mode no external CLK or Data provided - 15 - A on pin VDDD; Power-down mode; internal oscillator enabled; no external CLK or Data provided - 50 - A THD+N = 1 %; RL = 8 ; VBAT = 4.0 V - 6.6 - W IDDD Po(AV) digital supply current average output power 5. Ordering information Table 2. Ordering information Type number TFA9892AUK/N1 Package Name Description Version WLCSP49 wafer level chip-scale package; 49 bumps; 3.13 3.63 0.5 mm SOT1444-8 TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 3 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection 6. Block diagram 9''' $'6 $'6 9%$7 7)$ ,17 9%67 $'$37,9( '&WR'& &219(57(5 0 8 ; ,54 ,1% *1'% 9''3 '&,16(/ 567 5$0520 0(025< 5(*,67(56 6&/ ,& 6'$ VL VL )6 VL %&. VR ',2 VR ',2 VR ',2 VR VR 0 8 ; )6 VR 7'0 ,6 VR ',26(/ 0 8 ; 5 / 287$ * $ , 1 ,17 ORRSEDFN 67*$,1 GFGFH[W *$,1 '(&VW $(& &$5'(&,6(/ '632 '(&YV *DLQ2 0 8 ; 9ROWDJH6HQVH '(&FV SUR '$7$ 6(/(&725 0 8 ; $'& &$5'(&,6(/ 7(036(16( 0 8 ; 287% 63($.(5 3527(&7,21 ORRSEDFN SUR ',2 63'0, &/$66' $8',2 $03/,),(5 9 7'063.* $03,16(/ *DLQ,Q &XUUHQW6HQVH %&. 3'0&/ 3 : 0 3// 3527(&7,21 273 893 2&3 ,'3 9%$76(16( 26& *1'3 *1'' 9''36(16( 3'0 ,1387 3'0 287387 3'02 7(67 Fig 1. 7(67 7(67 7(67 7(67 7(67 DDD Block diagram TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 4 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection 7. Pinning information 7.1 Pinning * & ' ' & ( % ) $ Fig 2. % ( a. Bottom view $ ) EXPS$ LQGH[DUHD EXPS$ LQGH[DUHD * DDD DDD b. Transparent top view Bump configuration TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 5 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection $ )6 ',2 ',2 ,17 *1'' 287% 9''3 % %&. *1'' ',2 567 *1'3 *1'3 9''3 & ',263' 0, *1'' 7(67 7(67 *1'' 287$ 9''3 ' )6 *1'' 7(67 7(67 *1'' 287$ 287$ 63'02 7(67 7(67 *1'% ,1% 9%67 ( %&.3'0 &/. ) 6'$ $'6 $'6 *1'' *1'% ,1% 9%67 * 6&/ 9%$7 9''' *1'' *1'% ,1% 9%67 DDD Transparent top view Fig 3. TFA9892_SDS Product short data sheet Bump mapping All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 6 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection Table 3. TFA9892_SDS Product short data sheet Pinning Symbol Pin Type Description FS1 A1 I digital audio Frame Sync for DIO1 DIO1 A2 I/O digital audio interface DIO1 DIO4 A3 I/O digital audio data in / out DIO4 INT A4 O interrupt output; open if unused GNDD A5 P digital ground OUTB A6 O inverting output VDDP A7 P power supply voltage BCK1 B1 I digital audio bit clock DIO1 GNDD B2 P digital ground DIO3 B3 I digital audio data in/out DIO3 RST B4 I reset input GNDP B5 P power ground GNDP B6 P power ground VDDP B7 P power supply voltage DIO2/ SPDMI C1 I/O digital audio data in/out DIO2 / SPDM data input GNDD C2 P digital ground TEST3 C3 O test signal input 3; for test purposes only, connect to PCB ground TEST2 C4 O test signal input 2; for test purposes only, connect to PCB ground GNDD C5 P digital ground OUTA C6 O non-inverting output VDDP C7 P power supply voltage FS2 D1 I digital audio word select for DIO2 GNDD D2 P digital ground TEST4 D3 O test signal input 4; for test purposes only, connect to PCB ground TEST1 D4 O test signal input 1; for test purposes only, connect to PCB ground GNDD D5 P digital ground OUTA D6 - non-inverting output[1] OUTA D7 - non-inverting output[1] BCK2/ PDMCLK E1 I digital audio bit clock DIO2 or PDM clock input SPDMO E2 O PDM output; output open if unused TEST5 E3 O test signal input 5; for test purposes only, connect to PCB ground TEST6 E4 O test signal input 6; for test purposes only, connect to PCB ground GNDB E5 P boosted ground INB E6 P DC-to-DC boost converter input VBST E7 O boosted supply voltage output SDA F1 I/O I2C-bus data input/output ADS1 F2 I address select input 1 ADS2 F3 I address select input 2 GNDD F4 P digital ground All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 7 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection Table 3. Symbol Pin Type Description GNDB F5 P boosted ground INB F6 P DC-to-DC boost converter input VBST F7 O boosted supply voltage output SCL G1 I I2C-bus clock input VBAT G2 P battery supply voltage sense input VDDD G3 P digital supply voltage GNDD G4 P digital ground GNDB G5 P boosted ground INB G6 P DC-to-DC boost converter input VBST G7 O boosted supply voltage output [1] TFA9892_SDS Product short data sheet Pinning ...continued Is used to simplify routing to OUTA All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 8 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection 8. Functional description The TFA9892 is a highly efficient mono Bridge Tied Load (BTL) class-D audio amplifier with a sophisticated SpeakerBoost protection algorithm. Figure 1 is a block diagram of the TFA9892. A SpeakerBoost protection algorithm, running on a CoolFlux Digital Signal Processor (DSP) core, maximizes the acoustical output of the speaker while limiting membrane excursion and voice coil temperature to a safe level. The mechanical protection implemented guarantees that speaker membrane excursion never exceeds its rated limit, to an accuracy of 10 %. Thermal protection guarantees that the voice coil temperature never exceeds its rated limit, to an accuracy of 10 C. Furthermore, advanced signal processing ensures the audio quality remains acceptable at all times. The protection algorithm implements an adaptive loudspeaker model that is used to predict the extent of membrane excursion. The model is continuously updated to ensure that the protection scheme remains effective even when speaker parameter values change or the acoustic enclosure is modified. Output sound pressure levels are boosted within given mechanical, thermal and quality limits. An optional Bandwidth extension mode extends the low frequency response up to a predefined limit before maximizing the output level. This mode is suitable for listening to high quality music in quiet environments. The frequency response of the TFA9892 can be modified via ten fully programmable cascaded second-order biquad filters. The first two biquads are processed with 48-bit double precision; biquads 3 to 10 are processed with 24-bit single precision. At low battery voltage levels, the gain is automatically reduced to limit battery current. The output volume can be controlled by the SpeakerBoost protection algorithm or by the host application (external). In the latter case, the boost features of the SpeakerBoost protection algorithm must be disabled to avoid neutralizing external volume control. The SpeakerBoost protection algorithm output is converted into two pulse width modulated (PWM) signals which are then injected into the class-D audio amplifier. The 3-level PWM scheme supports filterless speaker drive. An adaptive DC-to-DC converter boosts the battery supply voltage in line with the output of the SpeakerBoost protection algorithm. It switches to Follower mode (VBST = VBAT; no boost) when the audio output voltage is lower than the battery voltage. Next to adaptive DC to DC a PFM mode is selected when the requested output current is low. The adaptive boost and PFM mode ensures a high efficiency ClassHD Amplifier. It contains four TDM/I2S input/output (DIO) ports. These ports can be selected as an input or an output on demand. i.e. DIO1 and DIO2, can be selected as the audio input stream. DIO3 is provided to support stereo applications, while DIO4 can be used to provide stereo AEC as well. DIO1, DIO3 and DIO4 are clocked by FS1 and BCK1, while DIO2 is clocked by FS2 and BCK2; see Figure 1). DIO 3, 4 can be as well configured to transmit the DSP output signal, amplifier output current and voltage information, or amplifier gain information. The gain information can be used to facilitate communication between two devices in stereo applications. TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 9 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection A `pass-through' option allows one of the DIO1, 2, 3 as input to be connected directly to the DIO4 output. The pass-through option is provided to allow an output slave device (e.g. a CODEC), connected in parallel with the TFA9892, to be routed directly to the audio host via DIO4 output. TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 10 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection 9. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit Vx voltage on pin x on pin VBAT 0.3 +6 V on pins VBST, VDDP 0.3 +12.4 V on pin INB, OUTA, OUTB 0.3 +13.4[1] V on pin VDDD 0.3 +2.5 V on SCL, SDA, DIO1, DIO2, DIO3, DIO4 0.3 +2.5 V Tj junction temperature 40 +150 C Tstg storage temperature 55 +150 C Tamb ambient temperature 40 +85 C VESD electrostatic discharge voltage according to Human Body Model (HBM) 2 +2 kV according to Charge Device Model (CDM) 500 +500 V [1] Using an NXP demo board with a 1 mm wire/PCB track length on pin INB, AC pulses up to 18 V and 9 V can be observed without causing any damage as these spikes only partly penetrate the device (which is protected by internal clamp circuits). 10. Thermal characteristics Table 5. Thermal characteristics Symbol Parameter Conditions Typ Unit Rth(j-a) thermal resistance from junction to ambient 4-layer application board 35 K/W TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 11 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection 11. Characteristics 11.1 DC Characteristics Table 6. DC characteristics All parameters are guaranteed for VBAT = 3.6 V; VDDD = 1.8 V; VDDP = VBST = 12 V, adaptive boost mode; LBST = 1 H[1]; RL = 8 [1]; LL = 40 H[1]; fi = 1 kHz; fs = 48 kHz; Tamb = 25 C; default settings, unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit VBAT battery supply voltage on pin VBAT 2.7 - 5.5 V IBAT battery supply current on pin VBAT and in DC-to-DC converter coil; Operating modes with load; DC-to-DC converter in Adaptive Boost mode (no output signal, VBAT = 3.6 V; VDDD = 1.8 V) - 2.45 - mA Power-down mode - 1 5 A 2.7 - 12.2 V 1.65 1.8 1.95 V VDDP power supply voltage on pin VDDP VDDD digital supply voltage on pin VDDD; Brown out detector (BOD) disabled. IDDD digital supply current on pin VDDD; Operating mode; no audio stream at the input; DSP enabled; SpeakerBoost activated - 20 - mA Operating mode; no audio content; DSP bypassed - 4.5 - mA Power-down mode - 15 - A Power-down mode; internal oscillator enabled - 50 - A [3] Pins DIO1,2,3,4, BCK1, FS1, BCK2, FS2, ADS1, ADS2, SCL, SDA VIH HIGH-level input voltage 0.7VDDD - VDDD V VIL LOW-level input voltage - - 0.3VDDD V - - 3 pF - - 0.1 A Cin input capacitance ILI input leakage current [2] 1.8 V on input pin Pins DIO1,2,3,4, SPDMI, INT, push-pull output stages VOH HIGH-level output voltage IOH = 4 mA - - VDDD 0.4 V VOL LOW-level output voltage IOL = 4 mA - - 400 mV Pins SDA, open drain outputs, external 10 k resistor to VDDD VOH HIGH-level output voltage IOH = 4 mA - - VDDD 0.4 V VOL LOW-level output voltage IOL = 4 mA - - 400 mV Amplifier Active, NMOS + PMOS VDDP = 12 V - 600 - m Pins OUTA, OUTB RDSon drain-source on-state resistance Protection Tact(th_prot) thermal protection activation temperature 130 - 150 C Vuvp(VBAT) undervoltage protection voltage on pin VBAT 2.3 - 2.5 V TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 12 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection Table 6. DC characteristics ...continued All parameters are guaranteed for VBAT = 3.6 V; VDDD = 1.8 V; VDDP = VBST = 12 V, adaptive boost mode; LBST = 1 H[1]; RL = 8 [1]; LL = 40 H[1]; fi = 1 kHz; fs = 48 kHz; Tamb = 25 C; default settings, unless otherwise specified. Symbol Parameter IO(ocp) overcurrent protection output current Conditions Min Typ Max Unit 2 - - A 11.8 12 12.2 V DC-to-DC converter VBST [1] maximum voltage on pin VBST Maximum boost voltage setting LBST = boost converter inductance; RL = load resistance; LL = load inductance (speaker). [2] This parameter is not tested during production; the value is guaranteed by design and checked during product validation. [3] If BOD is enabled min VDDD range goes to 1.7 V 11.2 AC characteristics Table 7. AC characteristics All parameters are guaranteed for VBAT = 3.6 V; VDDD = 1.8 V; VDDP = VBST = 12 V, adaptive boost mode; LBST = 1 H[1]; RL = 8 [1]; LL = 40 H[1]; fi = 1 kHz; fs = 48 kHz; Tamb = 25 C; default settings, unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Amplifier output power Po(AV) average output power Hands-free speaker THD+N = 1 %; VBAT = 4 V RL = 8 ; VBST = 12 V 6.6 W RL = 6 ; VBST = 10 V 6.6 W RL = 4 ; VBST = 8.5 V 6.7 W 8 W 2 W Hands-free speaker THD+N = 10 %; VBAT = 4 V RL = 8 ; VBST = 12 V Handset speaker THD+N = 1 %; VBST = 12 V; VBAT = 4 V Amplifier output; pins OUTA and OUTB VO(offset) output offset voltage absolute value - - 0.5 mV [2] - 80 - % [1] - - 0.1 % - 16 - V Amplifier performance po output power efficiency THD+N total harmonic distortion-plus-noise Po(RMS) = 100 mW; RL = 8 ; LL = 44 H Vn(o) output noise voltage Po(RMS) = 2.5 W; including DC-to-DC converter; 100 Hz audio signal A-weighted; no output signal; CoolFlux DSP bypassed; Handset mode; BCK clock jitter < 1 ns (PLL locked on BCK) DR dynamic range VO = 10 V (peak); A-weighted - 115 - dB S/N signal-to-noise ratio VO = 10 V (peak); A-weighted - 100 - dB PSRR power supply rejection ratio Vripple = 200 mV (RMS); fripple = 217 Hz - 75 - dB fsw switching frequency directly coupled to the TDM FS input frequency 256 - 384 kHz G(I2S-VO) I2S to VO gain Coolflux DSP bypassed, measured at input level -12 dBFS; TDMSPKG = 0 dB - 21 - dB VPOP pop noise voltage At mode transition and gain change 2 mV TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 13 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection Table 7. AC characteristics ...continued All parameters are guaranteed for VBAT = 3.6 V; VDDD = 1.8 V; VDDP = VBST = 12 V, adaptive boost mode; LBST = 1 H[1]; RL = 8 [1]; LL = 40 H[1]; fi = 1 kHz; fs = 48 kHz; Tamb = 25 C; default settings, unless otherwise specified. Symbol Parameter RL CL Conditions Min Typ Max Unit load resistance 4 8 32 load capacitance - - 200 pF PLL locked on BCK fs = 16 to 48 kHz - - 2 ms PLL locked on FS fs = 48 kHz - - 6 ms Amplifier power-up, power-down and propagation delays td(on) turn-on delay time td(off) turn-off delay time - - 10 s td(mute_off) mute off delay time - 1 - ms td(soft_mute) soft mute delay time Coolflux DSP enabled - 120 - ms tPD propagation delay CoolFlux DSP bypassed fs = 48 kHz - - 600 s SpeakerBoost protection mode, tLookAhead = 10 ms, fs = 48 kHz - - 12 ms - 75 - dB 3 - +3 % - 8 - kHz 30 - - H - 200 - pF [3] Current-sensing performance S/N signal-to-noise ratio IO = 1.2 A (peak); A-weighted Isense current sense mismatch IO = 0.5 A (peak) B bandwidth LL load inductance [2] RL 32 load capacitance CL to ground [4] [1] LBST = boost converter inductor; RL = load resistance; LL = load inductance (speaker). [2] This parameter is not tested during production; the value is guaranteed by design and checked during product validation. [3] The pilot tone is removed at the zero crossing after a soft mute, which takes on average 10 ms (20 ms max.) at a sample rate of 48 kHz and 15 ms (30 ms max.) at a sample rate of 16 kHz. [4] If a higher value is used, LPM should be disabled. TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 14 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection 11.3 TDM/I2S timing characteristics Table 8. TDM I2S bus interface characteristics; see Figure 4 All parameters are guaranteed for VBAT = 3.6 V; VDDD = 1.8 V; VDDP = VBST = 12 V, adaptive boost mode; LBST = 1 H[1]; RL = 8 [1]; LL = 40 H[1]; fi = 1 kHz; fs = 48 kHz; Tamb = 25 C; default settings, unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit fs sampling frequency on pin FS [2] 16 - 48 kHz fclk clock frequency on pin BCK [2] 32fs - 512fs Hz FS edge to BCK HIGH [3] 10 - - ns 10 - - ns 10 - - ns 10 - - ns PLL locked on BCK [4] - - 2 ns PLL locked on FS [5] - - 20 ns set-up time tsu DATA edge to BCK HIGH hold time th [3] BCK HIGH to FS edge BCK HIGH to DATA edge external clock jitter tJ [1] LBST = boost converter inductance; RL = load resistance; LL = load inductance. [2] The I2S bit clock input (BCK) is used as a clock input for the DSP, as well as for the amplifier and the DC-to-DC converter. Note that both the BCK and FS signals need to be present for the clock to operate correctly. [3] This parameter is not tested during production; the value is guaranteed by design and checked during product validation. [4] When the PLL is locked on BCK, amplifier output noise can deteriorate when clock jitter > 1 ns. [5] The system is less sensitive to jitter when the PLL is locked on FS. %&. WK WVX )6 '$7$ DDD Fig 4. TFA9892_SDS Product short data sheet TDM/I2S timing All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 15 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection 11.4 I2C timing characteristics Table 9. I2C-bus interface characteristics; see Figure 5 All parameters are guaranteed for VBAT = 3.6 V; VDDD = 1.8 V; VDDP = VBST = 12 V, adaptive boost mode; LBST = 1 H[1]; RL = 8 [1]; LL = 40 H[1]; fi = 1 kHz; fs = 48 kHz; Tamb = 25 C; default settings, unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit fSCL tLOW SCL clock frequency - - 400 kHz LOW period of the SCL clock 1.3 - - s tHIGH HIGH period of the SCL clock rise time tr 0.6 - - s SDA and SCL signals [2] 20 + 0.1 Cb - - ns SDA and SCL signals [2] 20 + 0.1 Cb - - ns [3] 0.6 - - s tf fall time tHD;STA hold time (repeated) START condition tSU;STA set-up time for a repeated START condition 0.6 - - s tSU;STO set-up time for STOP condition 0.6 - - s tBUF bus free time between a STOP and START condition 1.3 - - s tSU;DAT data set-up time 100 - - ns tHD;DAT data hold time 0 - - s 0 - 50 ns - - 400 pF tSP pulse width of spikes that must be suppressed by the input filter Cb capacitive load for each bus line [4] [1] LBST = boost converter inductance; RL = load resistance; LL = load inductance. [2] Cb is the total capacitance of one bus line in pF. The maximum capacitive load for each bus line is 400 pF. [3] After this period, the first clock pulse is generated. [4] To be suppressed by the input filter. 6'$ W/2: W%8) WU WI W+'67$ W63 6&/ W+'67$ 3 W+''$7 W+,*+ W68'$7 6 W6867$ 6U W68672 3 DDD Fig 5. TFA9892_SDS Product short data sheet I2C timing All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 16 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection 12. Application information 12.1 Application diagrams EDWWHU\ 5)9%$7 &75/ O& &)9%$7 ) + &9%$7 ) ,1% 9''' &9''' ) /%67 9%$7 9''' 6'$ 9%67 6&/ $8',2,1 9''3 ',2 )6 O6 &(0& Q) %&. $(& %$6(%$1' 352&(6625 &9''3 [) ',2 7)$ 567 287$ ,17 VSHDNHU 63'02 287% ',2 )6 %&. 7(67 7(67 7(67 7(67 7(67 7(67 *1'' *1'3 *1'% $'6 $'6 ',2 DDD Fig 6. Typical mono application TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 17 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection EDWWHU\ 5)9%$7 &75/ O & &)9%$7 ) + &9%$7 ) ,1% 9''' &9''' ) /%67 9%$7 9''' 6'$ 9%67 6&/ $8',2,1 9''3 ',2 )6 O 6 &(0& Q) %&. $(& %$6(%$1' 352&(6625 &9''3 [) 7)$ ',2 567 287$ ,17 63'02 VSHDNHU ',2 287% )6 %&. 7(67 7(67 7(67 7(67 7(67 7(67 *1'3 *1'' *1'% $'6 $'6 ',2 EDWWHU\ 5)9%$7 &)9%$7 ) + &9%$7 ) ,1% 9''' &9''' ) /%67 9%$7 9''' 6'$ 6&/ 9%67 ',2 9''3 )6 %&. &(0& Q) ',2 &9''3 [) 567 7)$ ,17 63'02 287$ ',2 )6 VSHDNHU %&. 287% 9''' Fig 7. 7(67 7(67 7(67 7(67 7(67 7(67 *1'3 *1'' *1'% $'6 $'6 ',2 DDD Typical stereo application TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 18 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection EDWWHU\ 5)9%$7 &75/ O & &)9%$7 ) + &9%$7 ) ,1% 9''' &9''' ) /%67 9%$7 9''' 6'$ 9%67 6&/ $8',2,1 9''3 ',2 )6 O 6 &(0& Q) %&. $(& %$6(%$1' 352&(6625 &9''3 [) ',2 7)$ 567 ,17 287$ 63'02 VSHDNHU ',2 287% )6 %&. 7(67 7(67 7(67 7(67 7(67 7(67 *1'3 *1'' *1'% $'6 $'6 ',2 EDWWHU\ 5)9%$7 &)9%$7 ) 5+9%$7 0 ,1% 9''' &9''' ) 9%$7 9''' 6'$ 6&/ 9%67 ',2 9''3 )6 %&. &9''3 [) ',2 567 7)$ ,17 63'02 ',2 287$ )6 VSHDNHU %&. 287% 9''' Fig 8. 7(67 7(67 7(67 7(67 7(67 7(67 *1'3 *1'' *1'% $'6 $'6 ',2 DDD Stereo application using single coil TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 19 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection 13. Package outline :/&63ZDIHUOHYHOFKLSVFDOHSDFNDJHEXPSV[[PP ' % 627 $ EDOO$ LQGH[DUHD $ $ ( $ GHWDLO; & H H =( & $ % & Y Z E \ * H ) ( H ' & % =( $ =' EDOO$ LQGH[DUHD ; =' PP VFDOH 'LPHQVLRQV PPDUHWKHRULJLQDOGLPHQVLRQV 8QLW PD[ QRP PLQ PP $ $ $ E ' ( H H H Y Z \ =' =' =( =( VRWBSR 2XWOLQH YHUVLRQ 627 Fig 9. 5HIHUHQFHV ,(& -('(& -(,7$ (XURSHDQ SURMHFWLRQ ,VVXHGDWH Package outline TFA9892AUK/N1 (WLCSP49) TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 20 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection 14. Soldering of WLCSP packages 14.1 Introduction to soldering WLCSP packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering WLCSP (Wafer Level Chip-Size Packages) can be found in application note AN10439 "Wafer Level Chip Scale Package" and in application note AN10365 "Surface mount reflow soldering description". Wave soldering is not suitable for this package. All NXP WLCSP packages are lead-free. 14.2 Board mounting Board mounting of a WLCSP requires several steps: 1. Solder paste printing on the PCB 2. Component placement with a pick and place machine 3. The reflow soldering itself 14.3 Reflow soldering Key characteristics in reflow soldering are: * Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see Figure 10) than a SnPb process, thus reducing the process window * Solder paste printing issues, such as smearing, release, and adjusting the process window for a mix of large and small components on one board * Reflow temperature profile; this profile includes preheat, reflow (in which the board is heated to the peak temperature), and cooling down. It is imperative that the peak temperature is high enough for the solder to make reliable solder joints (a solder paste characteristic) while being low enough that the packages and/or boards are not damaged. The peak temperature of the package depends on package thickness and volume and is classified in accordance with Table 10. Table 10. Lead-free process (from J-STD-020D) Package thickness (mm) Package reflow temperature (C) Volume (mm3) < 350 350 to 2000 > 2000 < 1.6 260 260 260 1.6 to 2.5 260 250 245 > 2.5 250 245 245 Moisture sensitivity precautions, as indicated on the packing, must be respected at all times. Studies have shown that small packages reach higher temperatures during reflow soldering, see Figure 10. TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 21 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection maximum peak temperature = MSL limit, damage level temperature minimum peak temperature = minimum soldering temperature peak temperature time 001aac844 MSL: Moisture Sensitivity Level Fig 10. Temperature profiles for large and small components For further information on temperature profiles, refer to application note AN10365 "Surface mount reflow soldering description". 14.3.1 Stand off The stand off between the substrate and the chip is determined by: * The amount of printed solder on the substrate * The size of the solder land on the substrate * The bump height on the chip The higher the stand off, the better the stresses are released due to TEC (Thermal Expansion Coefficient) differences between substrate and chip. 14.3.2 Quality of solder joint A flip-chip joint is considered to be a good joint when the entire solder land has been wetted by the solder from the bump. The surface of the joint should be smooth and the shape symmetrical. The soldered joints on a chip should be uniform. Voids in the bumps after reflow can occur during the reflow process in bumps with high ratio of bump diameter to bump height, i.e. low bumps with large diameter. No failures have been found to be related to these voids. Solder joint inspection after reflow can be done with X-ray to monitor defects such as bridging, open circuits and voids. 14.3.3 Rework In general, rework is not recommended. By rework we mean the process of removing the chip from the substrate and replacing it with a new chip. If a chip is removed from the substrate, most solder balls of the chip will be damaged. In that case it is recommended not to re-use the chip again. TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 22 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection Device removal can be done when the substrate is heated until it is certain that all solder joints are molten. The chip can then be carefully removed from the substrate without damaging the tracks and solder lands on the substrate. Removing the device must be done using plastic tweezers, because metal tweezers can damage the silicon. The surface of the substrate should be carefully cleaned and all solder and flux residues and/or underfill removed. When a new chip is placed on the substrate, use the flux process instead of solder on the solder lands. Apply flux on the bumps at the chip side as well as on the solder pads on the substrate. Place and align the new chip while viewing with a microscope. To reflow the solder, use the solder profile shown in application note AN10365 "Surface mount reflow soldering description". 14.3.4 Cleaning Cleaning can be done after reflow soldering. TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 23 of 27 TFA9892 NXP Semiconductors 12 V boosted audio system with adaptive sound maximizer and speaker protection 15. Revision history Table 11. Revision history Document ID Release date Data sheet status Change notice Supersedes TFA9892_SDS v.1 20170901 Product short data sheet - - TFA9892_SDS Product short data sheet All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 24 of 27 D D D D D R R R R R FT FT FT FT FT TFA9892 D R R FT FT FT FT A A A A R R D D D 12 V boosted audio system with adaptive sound maximizer and speaker protection D R R A FT FT FT A A R R D D D R F D FT FT A A R R D 16.1 Data sheet status A FT FT A A R R D D D 16. Legal information A A A A A NXP Semiconductors D D R Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. A Document status[1][2] FT D R A [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 16.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 16.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. TFA9892_SDS Product short data sheet Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 25 of 27 D D D D D R R R R R D R R FT D R A F D FT FT A A R R D D D R Translations -- A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. A FT D R A 16.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. CoolFlux -- is a trademark of NXP B.V. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Product short data sheet R A FT FT A A R R D D whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. 17. Contact information TFA9892_SDS D R FT FT A A R R D D D In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) FT FT FT FT Non-automotive qualified products -- Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. A A A A R R D D D Quick reference data -- The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. FT FT FT FT FT TFA9892 12 V boosted audio system with adaptive sound maximizer and speaker protection Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. A A A A A NXP Semiconductors All information provided in this document is subject to legal disclaimers. Rev. 1.0 -- 1 September 2017 (c) NXP B.V. 2017. All rights reserved. 26 of 27 D D D D D R R R R R D R R FT FT FT FT D R R A FT FT FT A A R R D D D R A F FT FT A A R R D D D D FT FT A A R R D General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 2 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Quick reference data . . . . . . . . . . . . . . . . . . . . . 3 Ordering information . . . . . . . . . . . . . . . . . . . . . 3 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pinning information . . . . . . . . . . . . . . . . . . . . . . 5 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional description . . . . . . . . . . . . . . . . . . . 9 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 11 Thermal characteristics . . . . . . . . . . . . . . . . . 11 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 12 DC Characteristics . . . . . . . . . . . . . . . . . . . . . 12 AC characteristics. . . . . . . . . . . . . . . . . . . . . . 13 TDM/I2S timing characteristics . . . . . . . . . . . . 15 I2C timing characteristics . . . . . . . . . . . . . . . . 16 Application information. . . . . . . . . . . . . . . . . . 17 Application diagrams . . . . . . . . . . . . . . . . . . . 17 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 20 Soldering of WLCSP packages. . . . . . . . . . . . 21 Introduction to soldering WLCSP packages . . 21 Board mounting . . . . . . . . . . . . . . . . . . . . . . . 21 Reflow soldering . . . . . . . . . . . . . . . . . . . . . . . 21 Stand off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Quality of solder joint . . . . . . . . . . . . . . . . . . . 22 Rework . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 24 Legal information. . . . . . . . . . . . . . . . . . . . . . . 25 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 25 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Contact information. . . . . . . . . . . . . . . . . . . . . 26 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 A A A A R R D D D D D R A FT D R A 1 2 3 4 5 6 7 7.1 8 9 10 11 11.1 11.2 11.3 11.4 12 12.1 13 14 14.1 14.2 14.3 14.3.1 14.3.2 14.3.3 14.3.4 15 16 16.1 16.2 16.3 16.4 17 18 FT FT FT FT FT TFA9892 12 V boosted audio system with adaptive sound maximizer and speaker protection 18. Contents A A A A A NXP Semiconductors Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2017. All rights reserved. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 1 September 2017 Document identifier: TFA9892_SDS