ARDUIN O M K R 1 000 WI F I
Code: ABX00004
Arduino MKR1000 is a powerful board that combines the functionality of the Zero
and the Wi-Fi Shield. It is the ideal solution for makers wanting to design IoT
projects with minimal previous experience in networking.
Arduino MKR1000 has been designed to offer a practical and cost effective solution for makers seeking to
add Wi-Fi connectivity to their projects with minimal previous experience in networking.It is based on the
Atmel ATSAMW25 SoC (System on Chip), that is part of the SmartConnect family of Atmel Wireless devices,
specifically designed for IoT projects and devices.
The ATSAMW25 is composed of three main blocks:
SAMD21 Cortex-M0+ 32bit low power ARM MCU
WINC1500 low power 2.4GHz IEEE® 802.11 b/g/n Wi-Fi
ECC508 CryptoAuthentication
The ATSAMW25 includes also a single 1x1 stream PCB Antenna.
The design includes a Li-Po charging circuit that allows the Arduino/Genuino MKR1000 to run on battery
power or external 5V, charging the Li-Po battery while running on external power. Switching from one source
to the other is done automatically.A good 32 bit computational power similar to the Zero board, the usual rich
set of I/O interfaces, low power Wi-Fi with a Cryptochip for secure communication, and the ease of use of the
Arduino Software (IDE) for code development and programming.
All these features make this board the preferred choice for the emerging IoT battery-powered projects in a
compact form factor.
The USB port can be used to supply power (5V) to the board.The Arduino MKR1000 is able to run with or
without the Li-Po battery connected and has limited power consumption.
The MKR1000 Wifi module supports certificate SHA-256.
Warning: Unlike most Arduino & Genuino boards, the MKR1000 runs at 3.3V. The maximum voltage
that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage
the board. While output to 5V digital devices is possible, bidirectional communication with 5V
devices needs proper level shifting.
TECH SPECS
Microcontroller SAMD21 Cortex-M0+ 32bit low power ARM MCU
Board Power Supply (USB/VIN) 5V
Supported Battery(*) Li-Po single cell, 3.7V, 700mAh minimum
Circuit Operating Voltage 3.3V
Digital I/O Pins 8
PWM Pins 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19)
UART 1
SPI 1
I2C 1
Analog Input Pins 7 (ADC 8/10/12 bit)
Analog Output Pins 1 (DAC 10 bit)
External Interrupts 8 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17)
DC Current per I/O Pin 7 mA
Flash Memory 256 KB
SRAM 32 KB
EEPROM no
Clock Speed 32.768 kHz (RTC), 48 MHz
LED_BUILTIN 6
Full-Speed USB Device and embedded Host
LED_BUILTIN 6
Length 61.5 mm
Width 25 mm
Weight 32 gr.
OSH: Schematics
The MKR1000 is open-source hardware! You can build your own board using the following files:
EAGLE FILES IN .ZIPSCHEMATICS IN .PDFFRITZING IN .FZPZ
Pinout
Download the pinout in PNG format
Li-Po batteries, Pins and board LEDs
Battery capacity
Li-Po batteries are charged up to 4,2V with a current that is usually half of the nominal capacity (C/2). For
Arduino / Genuino MKR1000 we use a specialized chip that has a preset charging current of 350mAh. This
means that the MINIMUM capacity of the Li-Po battery should be 700 mAh. Smaller cells will be damaged by
this current and may overheat, develop internal gasses and explode, setting on fire the surroundings. We
strongly recommend that you select a Li-Po battery of at least 700mAh capacity. A bigger cell will take more
time to charge, but won't be harmed or overheated. The chip is programmed with 4 hours of charging time,
then it goes into automatic sleep mode. This will limit the amount of charge to max 1400 mAh per charging
round.
Battery connector
If you want to connect a battery to your MKR1000 be sure to search one with female 2 pin JST PHR2 Type
connector.Polarity : looking at the board connector pins, polarity is Left = Positive, Right = GNDDownload
here the Connector datasheet. On the MKR1000, connector is a Male 2pin JST PH Type.VinThis pin can be
used to power the board with a regulated 5V source. If the power is fed through this pin, the USB power
source is disconnected. This is the only way you can supply 5v (range is 5V to maximum 6V) to the board
not using USB. This pin is an INPUT.
5V
This pin outputs 5V from the the board when powered from the USB connector or from the VIN pin of the
board. It is unregulated and the voltage is taken directly from the inputs. When powered from battery it
supplies around 3.7 V. As an OUTPUT, it should not be used as an input pin to power the board.
VCC
This pin outputs 3.3V through the on-board voltage regulator. This voltage is the same regardless the power
source used (USB, Vin and Battery).
LED ON
This LED is connected to the 5V input from either USB or VIN. It is not connected to the battery power. This
means that it lits up when power is from USB or VIN, but stays off when the board is running on battery
power. This maximizes the usage of the energy stored in the battery. It is therefore normal to have the board
properly running on battery power without the LED ON being lit.
CHARGE LED
The CHARGE LED on the board is driven by the charger chip that monitors the current drawn by the Li-Po
battery while charging. Usually it will lit up when the board gets 5V from VIN or USB and the chip starts
charging the Li-Po battery connected to the JST connector.There are several occasions where this LED will
start to blink at a frequency of about 2Hz. This flashing is caused by the following conditions maintained for a
long time (from 20 to 70 minutes):- No battery is connected to JST connector.- Overdischarged/damaged
battery is connected. It can't be recharged.- A fully charged battery is put through another unnecessary
charging cycle. This is done disconnecting and reconnecting either VIN or the battery itself while VIN is
connected.
Onboard LED
On MKR1000 the onboard LED is connected to D6 and not D13 as on the other boards. Blink example or
other sketcthes that uses pin 13 for onboard LED may need to be changed to work properly.
(*) Note : DO NOT CONNECT to the male JST connector present on the board anything else than a
Li-Po battery whose characteristics are compliant with those indicated above. Please DO NOT
POWER VIN with more than 5V.
