PM4H-A PM4H-S PM4H-M DIN48 SIZE MULTI-RANGE ANALOG TIMER FEATURES * * * * 48 1.89 48 1.89 * * * * mm inch 62.5 2.46 Socket mount Front panel of IP65 type is protected against water-splash and dust 100-240V AC free-voltage input Built-in Screw terminals Screw terminal type is used for easy wiring and reducing additional cost for accessories. 8 different operation modes: (PM4H-A) Tube base with pin style terminals Multiple time ranges -- 1 s to 500 h (Max.) Short body -- 62.5mm 2.46 inch (screw terminal type) Flush mount PRODUCT TYPE Type Contact arrangement Operation mode Time range Protective construction Rated operating voltage 100 to 240V AC PM4H-A IP65 8 operation modes * Pulse ON-delay * Pulse Flicker * Pulse ON-flicker * Differential ON/OFF-delay (1) (2) * Signal OFF-delay * Pulse One-shot * Pulse One-cycle 24V AC/DC 12V DC Relay Timed-out 2 Form C 100 to 240V AC IP50 24V AC/DC 12V DC 100 to 240V AC IP65 PM4H-S Relay Timed-out 2 Form C Power ON-delay 24V AC/DC 12V DC 16 selectable ranges 1s to 500h 100 to 240V AC IP50 24V AC/DC 12V DC 100 to 240V AC PM4H-M IP65 5 operation modes (With instantaneous contact) * Power ON-delay * Power Flicker * Power ON-flicker * Power One-shot * Power One-cycle 24V AC/DC Relay Timed-out 1 Form C Instantaneous 1 Form C 12V DC 100 to 240V AC IP50 24V AC/DC 12V DC If you use this timer under harsh environment, please order above sealed type (IP65 type). IP65 type -- Protection dust and TIME RANGE Time unit Scale 1 5 10 50 Control time range sec min hrs 10h 0.1s to 1s 0.1 min to 1 min 0.1h to 1h 1.0h to 10h 0.5s to 5s 0.5 min to 5 min 0.5h to 5h 5h to 50h 1.0s to 10s 1.0 min to 10 min 1.0h to 10h 10h to 100h 5s to 50s 5 min to 50 min 5h to 50h 50h to 500h Note: 0 setting is for instantaneous output operation. 30 Terminal type Part No. PM4HA-H-AC240VW 11 pin Screw terminal PM4HA-H-AC240VSW PM4HA-H-24VW 11 pin Screw terminal PM4HA-H-24VSW PM4HA-H-DC12VW 11 pin Screw terminal PM4HA-H-DC12VSW PM4HA-H-AC240V 11 pin Screw terminal PM4HA-H-AC240VS PM4HA-H-24V 11 pin Screw terminal PM4HA-H-24VS PM4HA-H-DC12V 11 pin Screw terminal PM4HA-H-DC12VS PM4HS-H-AC240VW 8 pin Screw terminal PM4HS-H-AC240VSW PM4HS-H-24VW 8 pin Screw terminal PM4HS-H-24VSW PM4HS-H-DC12VW 8 pin Screw terminal PM4HS-H-DC12VSW PM4HS-H-AC240V 8 pin Screw terminal PM4HS-H-AC240VS PM4HS-H-24V 8 pin Screw terminal PM4HS-H-24VS PM4HS-H-DC12V 8 pin Screw terminal PM4HS-H-DC12VS PM4HM-H-AC240VW 8 pin Screw terminal PM4HM-H-AC240VSW PM4HM-H-24VW 8 pin Screw terminal PM4HM-H-24VSW PM4HM-H-DC12VW 8 pin Screw terminal PM4HM-H-DC12VSW PM4HM-H-AC240V 8 pin Screw terminal PM4HM-H-AC240VS PM4HM-H-24V 8 pin Screw terminal PM4HM-H-24VS PM4HM-H-DC12V 8 pin Screw terminal PM4HM-H-DC12VS water jet splay on the front face. PM4H-A/PM4H-S/PM4H-M All types of PM4H timer have multi-time range. 16 time ranges are selectable. 1s to 500h (Max. range) is controlled. CHARACTERISTICS Type Item PM4H-A PM4H-S 100 to 240V AC, 12V DC, 24V AC/DC 50/60Hz common (AC operating type) Max. 10VA (100 to 240V AC) Max. 2.5VA (24V AC) Max. 2W (12V DC, 24V DC) 5A 250V AC (resistive load) Rated operating voltage Rated frequency Rated power consumption Output rating PM4H-M Pulse ON-delay Power ON-delay Pulse Flicker Power Flicker Pulse ON-Flicker Power ON-flicker Differential ON/OFF-delay (1) (2) Power ON-delay Operating mode Power One-shot Signal OFF-delay Power One-cycle Pulse One-shot (with instantaneous contact) Pulse One-cycle 1s to 500h (Max.) 16 time ranges switchable Time range 0.3% (power off time change at the range of 0.1s to 1h) Operating time fluctuation Time 5% Setting error accuracy 0.5% (at the operating voltage changes between 85 to 110%) Note:) Voltage error 2% (at 20C ambient temp. at the range of -10 to +50C +14 to +122F) Temperature error Timed-out 1 Form C Contact arrangement Timed-out 2 Form C Instantaneous 1 Form C Contact Max. 100m (at 1A 6V DC) Contact resistance (Initial value) Contact material Silver alloy Au flash on Silver alloy Mechanical (contact) 2x107 Life Electrical (contact) 105 (at rated control capacity) Allowable operating voltage range 85 to 110% of rated operating voltage (at 20C coil temp.) Between live and dead metal parts Between input and output Insulation resistance (Initial value) Min. 100M Between contacts of different poles Between contacts of same pole Electrical 2,000Vrms for 1 min Between live and dead metal parts function 2,000Vrms for 1 min Between input and output Breakdown voltage (Initial value) 2,000Vrms for 1 min Between contacts of different poles 1,000Vrms for 1 min Between contacts of same pole Min. power off time 100ms Max. temperature rise 55C 131F Functional Min. 98m/s2 (4 times on 3 axes) Shock resistance Min. 980m/s2 (5 times on 3 axes) Destructive Mechanical function Functional 10 to 55Hz: 1 cycle/min double amplitude of 0.5mm (10min on 3 axes) Vibration resistance 10 to 55Hz: 1 cycle/min double amplitude of 0.75mm (1h on 3 axes) Destructive Ambient temperature -10 to +50C +14 to +122F Ambient humidity Max. 85%RH Operating condition Atmospheric pressure 860 to 1,060hPa Ripple factor (DC type) 20% Protective construction IP65 on front panel (using rubber gasket ATC18002) <only for IP65 type> 100g 3.527 oz (Pin type) Others Weight 110g 3.880 oz (Screw terminal type) Note: 1) Unless otherwise specified, the measurement conditions at the maximum scale time standard are specified to be the rated operating voltage (within 5% ripple factor for DC), 20C 68F ambient temperature, and 1s power off time. 2) For the 1s range, the tolerance for each specification becomes 10ms. Rating WIRING DIAGRAMS PM4H-A Pin type * Timed-out 2 Form C COM Reset Stop input input Signal input PM4H-S Pin type * Timed-out 2 Form C Screw terminal type * Timed-out contact 2 Form C N.C. COM Screw terminal type * Timed-out 2 Form C N.C. N.O. COM COM N.O. N.O. N.C. N.C. N.O. N.C. N.O. COM COM COM (-) Operating (+) voltage PM4H-M Pin type * Timed-out 1 Form C * Instantaneous 1 Form C N.C. Operating (+) voltage (-) Stop input Signal input Reset input COM Operating voltage (+) (+) Operating (-) voltage 1) DC Type PM4H-A COM N.C. N.O. COM (-) Type Screw terminal type * Timed-out 1 Form C * Instantaneous 1 Form C N.C. N.O. N.O. N.C. N.C. N.O. PM4H-S PM4H-M Pin Connect the terminal b to negative (-), and the terminal j to positive (+). Connect the terminal b to negative (-), and the terminal g to positive (+). Screw terminal Connect the terminal x to negative (-), and the terminal z to positive (+). N.O. N.O. N.C. N.C. N.O. 2) Contact COM COM (-) Operating voltage (+) (+) Operating (-) voltage Timed-out contact Instantaneous contact 31 PARTS NAME PM4H-S PM4H-A PM4H-M Power indicator LED Operation indicator LED Hand Time indicator window Set dial Time range indicator Operation mode indicator Time range selector 16 time settings selectable 1 s to 500 h Instantaneous output area 1s 5s 10s 50s 1min 5min 10min 50min When the hand is in this area, instantaneous operation starts. 1h 5h 10h 50h 10h 50h 100h 500h Operation mode selector Selectable from 8 operation modes ON : Pulse ON-delay FL : Pulse Flicker FO : Pulse ON-flicker OF1 : Differential ON/OFF-delay (1) SF : Signal OFF-delay OS : Pulse One-shot OF2 : Differential ON/OFF-delay (2) OC : Pulse One-cycle Operation mode selector Selectable from 5 operation modes ON : Pulse ON-delay FL : Pulse flicker FO : Pulse ON-flicker OS : Pulse One-shot OC : Pulse One-cycle mm inch DIMENSIONS * PM4H-w Screw terminal type (Flush mount) Pin type (Flush mount/Surface mount) 62.5 2.461 41 1.614 48 1.890 0 m44.5 1.752 48 1.890 0 * Panel mount dimensions (with mounting frame) Screw terminal type Rubber gasket ATC 18002 (attached) Rubber gasket ATC 18002 48 1.890 0 48 1.890 1 .039 * Surface mount dimensions Socket mount (Pin type) Din rail socket ATC18003 (8 pin) ATC18004 (11 pin) Mounting rail AT8-DLA1 95.3 (8 pin) 3.752 101.0 (11 pin) 3.976 32 m44.5 1.752 61.5 2.421 66 2.6 48 1.890 * Panel cut out dimensions Standard cut out dimensions are shown below. Use mounting frame and rubber gasket (ATC18002). 45+0.6 0 1.772+.024 0 45+0.6 0 1.772+.024 0 Min. 80 3.150 Panel Mounting frame AT8-DA4 50 1.969 66 2.6 14.5 .571 Socket (8 pin) AT8-RR When 11 pin timer is used, use the socket. AT8-DP11 Panel 50 1.969 0 66.5 2.618 m44.5 m1.752 Pin type Mounting frame AT8-DA4 (attached) 48 1.890 6.0 12.0 .236 .472 48 1.890 41 1.614 6.0 12.0 .236 .472 48 1.890 Min. 80 3.150 77 3.031 * Adjacent mounting 45+0.6 0 1.772+.024 0 A A = (48xn-2.5)+0.6 0 A = (1.890xn-.098)+.024 0 Note) 1. The proper thickness of mounting panel is between 1 to 5mm. 2. Adjacent mount is less water-resistant. OPERATION MODE LED lighting LED flickering T: Setting time t1, t2, ta, tb<T t1+t2=T PM4H-A Operation mode Pulse ON-delay ON Operation Turn the operation selector to ON . Power is applied continuously. When a start signal is applied, the time cycle begins. The output contacts change state after the time delay is completed. The contacts will return to their normal state when a reset signal is applied or power is removed. (Note: When a stop signal is applied during timing operation, the time cycle stops. When a stop signal is removed, the time cycle resumes where it left off.) Time chart ON OFF Power supply ON ON Operation signal b-f ON OFF OFF ON Reset b-g Stop b-e OFF ON OFF T t1 t2 ON ON OFF Time out (N.O. contact) OFF OP. LED POWER LED Note: Pulse OFF-Flicker FL Turn the operation selector to FL . Power is applied continuously. When a start signal is applied, the time cycle begins but the output contacts remain in their normal state. When the time delay is completed, the output contacts change state and next time cycle begins. When this time delay is completed, the output contacts return to their normal state. This cycle will repeat until a reset signal is applied or power is removed. (Note: When a stop signal is applied during timing operation, the time cycle stops. When a stop signal is removed, the time cycle resumes where it left off.) LED lighting or No LED lighting ON OFF Power supply ON ON Operation signal b-f OFF ON OFF OFF ON Reset b-g Stop b-e OFF ON OFF T T t1 ta t2 ON tb ON OFF Time out (N.O. contact) OFF OP. LED POWER LED Note: Pulse ON-flicker FO Differential ON/OFF-delay (1) OF1 Turn the operation selector to FO . Power is applied continuously. When a start signal is applied, the output contacts change state immediately and time cycle begins. When the time delay is completed, the output contacts change state and next time cycle begins. When the time delay is completed, the output contacts return to the normal state. This cycle will repeat until a reset signal is applied or power is removed. (Note: When a stop signal is applied during timing operation, the time cycle stops. When a stop signal is removed, the time cycle resumes where it left off.) Turn the operation selector to OF1 . Power is applied continuously. When a start signal is applied, the output contacts change state immediately and time cycle begins. The output contacts change state after the timing cycle is completed. When the start signal is removed, the output contacts change state and time cycle starts again. If operation signal is turned ON or OFF during timing operation, the time cycle will restart. The output contacts will return to their normal state when a reset signal is applied or power is removed. (Note: When a stop signals is applied during timing operation, the time cycle stops. When a stop signal is removed, the time cycle resumes where it left off.) LED lighting or No LED lighting ON OFF Power supply ON Operation signal b-f Signal OFF-delay SF ON OFF OFF OFF ON Reset b-g Stop b-e OFF ON OFF T T ta t2 t1 T tb ON OFF Time out (N.O. contact) OFF OP. LED POWER LED ON OFF Power supply ON ON Operation signal b-f OFF OFF ON Reset b-g OFF ON Stop b-e OFF T t1 ON t2 ta ON tb ON OFF Time out (N.O. contact) OFF OFF OP. LED Restart POWER LED Note: Turn the operation selector to SF . Power is applied continuously. When a start signal is applied, the output contacts change state immediately. When the start signal is removed the time cycle begins. The output contacts will return to their normal state when the time delay is completed. Reset will occur when a reset signal is applied or power is removed. (Note: When a stop signal is applied during timing operation, the time cycle stops. When a stop signal is removed, the time cycle resumes where it left off.) ON LED lighting or No LED lighting ON OFF Power supply ON Operation signal b-f ON OFF OFF ON Reset b-g OFF ON Stop b-e OFF T ta tb ON Time out (N.O. contact) OFF OP. LED POWER LED Note: LED lighting or No LED lighting Note: Keep 0.1s or more for power off time. Keep 0.05s or more for signal, stop, reset input time. 33 Operation mode Pulse One-shot OS Operation Turn the operation selector to OS . Power is applied continuously. When a start signal is applied, the output contacts change state immediately and time cycle begins. When the time delay is completed, the output contacts return to their normal state. The contacts will return to normal state when a reset signal is applied or power is removed. (Note: When a stop signal is applied during timing operation, the time cycle stops. When a stop signal is removed, the time cycle resumes where it left off.) Time chart ON OFF Power supply ON ON Operation signal b-f OFF OFF ON Reset b-g OFF ON Stop b-e OFF T T t1 ta t2 ON OFF Time out (N.O. contact) OP. LED POWER LED Note: Differential ON/OFF-delay (2) OF2 Pulse One-cycle OC Turn the operation selector to OF2 . Power is applied continuously. When a start signal is applied, the ON-delay time cycle begins and the output contacts remain in their normal state. The output contacts change state after time delay is completed. When the start signal is removed the OFF-delay time cycle begins. The output contacts return to their normal state after the time delay is completed. If the start signal is applied or removed during the timing operation, the output contacts will change state and the time cycle starts over. The contacts will return to their normal state when a reset signal is applied or power is removed. (Note: When a stop signal is applied during timing operation, the time cycle stops. When a stop signal is removed, the time cycle resumes where it left off.) Turn the operation selector to OC . Power is applied continuously. When a start signal is applied, the time cycle begins but the output contacts remain in their normal state. The output contacts change state for 0.8s after time delay is completed. Reset will occur when a reset signal is applied or power is removed. (Note: When a stop signal is applied during timing operation, the time cycle stops. When a stop signal is removed, the time cycle resumes where it left off.) LED lighting or No LED lighting ON OFF Power supply ON ON Operation signal b-f OFF OFF ON Reset b-g OFF ON Stop b-e OFF T t1 t2 ta ON tb ON OFF Time out (N.O. contact) OFF Restart OP. LED POWER LED Note: LED lighting or No LED lighting ON OFF Power supply ON ON Operation signal b-f ON OFF OFF OFF ON Reset b-g ON OFF OFF ON Stop b-e OFF T t T t1 ON t2 t OFF Time out (N.O. contact) ta ON OFF OP. LED POWER LED One pulse time (t): Approx. 0.8s Note: LED lighting or No LED lighting Note: Keep 0.1s or more for power off time. Keep 0.05s or more for signal, stop, reset input time. LED lighting T: Setting time PM4H-S Operation mode Operation When power is applied continuously, the time cycle begins. The output contacts change state after the time delay is completed. Time chart ON OFF Power supply T Time out (N.O. contact) Power ON-delay LED flickering ON OFF OP. LED POWER LED PM4H-M Operation mode Operation Power ON-delay Power ON-delay When power is applied continuously, the instantaneous output contact changes state and the timing cycle begins. The timed contact changes state after the time delay is completed. Reset will occur when power is removed. PM4H-M timers do not have external signal, reset and stop inputs. (For other operation modes, refer to the operation mode of PM4H-A.) ON Power Flicker FL Power ON-flicker FO Time chart Power ON-delay ON ON Power One-cycle T ON Instantaneous contact (N.O. contact) OP. LED POWER LED OC Note: Keep 0.1s or more for power off time. PM4H-M timers do not have each input which is signal, reset and stop. 34 OFF Time out (N.O. contact) Power One-shot OS OFF Power supply OFF