DC1774A-B - ANALOG DEVICES - Product.Network

dc1774a-bf

DEMO MANUAL DC1774A-B

DESCRIPTION

LTC6430-15

400MHz to 1000MHz Differential

ADC Driver/IF Amplifier

Demonstration circuit 1774A-B is a differential ADC

driver/IF amplifier featuring the LT C

6430-15. It is part

of the DC1774A demo board family supporting the

LTC643X-YY amplifier series. The DC1774A-B is opti-

mized for a frequency range of 400MHz to 1000MHz and

utilizes a minimum of passive external components to

configure the amplifier for this application.

Because the LTC6430-15 has 100Ω differential input and

output impedance, the demo circuit uses transformers

L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear

Technology Corporation. All other trademarks are the property of their respective owners.

BLOCK DIAGRAM

to convert the impedance to 50Ω single-ended so that it

can be easily evaluated with commercially available RF

test equipment.

Design files for this circuit board are available at

http://www.linear.com/demo

Figure 1. LTC6430-15 Block Diagram

VCC

9, 22

+IN

BIAS AND TEMPERATURE

COMPENSATION

15dB

GAIN

15dB

GAIN

GND

8, 14, 17, 23 AND PADDLE 25

GND

8, 14, 17, 23 AND PADDLE 25

–IN

+OUT

T_DIODE

–OUT

dc1774a-bf

DEMO MANUAL DC1774A-B

PERFORMANCE SUMMARY

Table 1. Typical Demo Board Performance Summary

SYMBOL PARAMETER CONDITIONS VALUE/UNIT

Power Supply

VCC Operating Supply Range All VCC Pins Plus OUT Pins 4.75 to 5.25V

ICC Current Consumption Total Current 160mA

TA = 25°C, VCC = 5V

FREQUENCY

(MHz)

POWER GAIN

|S21| (dB)

OUTPUT

THIRD ORDER

INTERCEPT

POINT (NOTE 1)

OIP3 (dBm)

OUTPUT

THIRD ORDER

INTERMODULATION

(NOTE 1)

OIM3 (dBm)

SECOND

HARMONIC

DISTORTION

(NOTE 2)

HD2 (dBc)

THIRD HARMONIC

DISTORTION

(NOTE 2)

HD3 (dBc)

OUTPUT 1dB

COMPRESSION

POINT

P1dB (dBm)

NOISE FIGURE

(NOTE 3)

NF (dB)

400 14.8 46.5 –89.0 –71.2 –81.2 22.9 3.8

500 14.6 46.6 –89.3 –80.3 –76.1 23.0 4.0

600 14.5 46.2 –88.3 –67.4 –73.2 22.7 4.2

700 14.4 45.2 –86.5 –64.7 –68.1 (Note 4) 22.4 4.3

800 14.2 43.0 –82.0 –61.6 –70.6 (Note 4) 22.0 4.7

900 13.9 43.3 –82.6 –65.0 –67.7 (Note 4) 21.7 4.7

1000 13.6 43.1 –82.1 –70.6 (Note 4) –64.5 (Note 4) 21.5 4.8

All figures are referenced to J7 (input port) and J8 (output port).

Note 1: 2-tone test condition: output power level = 2dBm/tone;

tone spacing = 1MHz.

Note 2: Single-tone test condition: output power level = 8dBm.

Note 3: Small-signal noise figure.

Note 4: Out of input and output transformers working frequency range.

Figure 2. Demo Board DC1774A-B S-Parameters

OPERATION

The demo circuit 1774A-B is a highly linear fixed-gain

amplifier. The LTC6430-15 is internally matched to a 100Ω

differential source and a load impedance from 20MHz to

1300MHz. Due to the unpopularity of 100Ω differential

test equipment, transformers have been added to convert

impedance from differential 100Ω to single-ended 50Ω

for the input and the output ports. The frequency range

of the circuit is limited by the balun transformers. Hence,

this demo board works best with a frequency range from

400MHz to 1000MHz. Figure 2 shows the performance

of the demo board.

FREQUENCY (MHz)

200

|S21| (dB)

|S11|, |S12|, |S22| (dB)

400 600

–28

–24

–20

–16

NOMINAL WORKING

FREQUENCY RANGE

–8

–4

–12

800 1000 1200

|S21|

|S22|

|S11|

|S12|

dc1774a-bf

DEMO MANUAL DC1774A-B

Figure 3. Simplified Demo Board DC1774A-B Schematic

OPERATION

Figure 3 shows the simplified demo circuit schematic. It

requires a minimum of passive supporting components.

The 2:1 transformers convert the differential to single-

ended 50Ω for compatibility with most test equipment.

The input and output DC blocking capacitors (C1, C2,

C3 and C4) are required because this device is internally

biased for optimal operation. The frequency appropriate

choke (L1 and L2) and the decoupling capacitors (C5, C21,

C22 and C23) provide bias to the RF ±OUT nodes. Only a

single 5V supply is necessary for VCC pins on the device.

An optional stability network has been added. It consists

of parallel 62pF (C8 and C9) and 348Ω (R1 and R2) to

ensure low frequency stability.

Table 2 shows the function of each input and output on

the board.

Table 2. DC1774A-B Board I/O Descriptions

CONNECTOR FUNCTION

J7 (+IN) Single-Ended Input. Impedance-Matched to 50Ω.

Drive from a 50Ω Network Analyzer or Signal

Source.

J8 (–OUT) Single-Ended Output. Impedance-Matched to 50Ω.

Drive from a 50Ω Network Analyzer or Spectrum

Analyzer.

E3 or J11 (VCC) Positive Supply Voltage Source.

E6 or J18 (GND) Negative Supply Ground.

dc1774a-bf

DEMO MANUAL DC1774A-B

ADDITIONAL INFORMATION

The particular element values shown in the demo board

schematic are chosen for wide bandwidth operation.

Depending on the desired frequency, performance may

be improved by the proper selection of these supporting

components.

As with any RF device, minimizing ground inductance is

critical. Care should be taken with the board layout because

of the exposed pad packages. The maximum number of

minimum diameter via holes should be placed underneath

the exposed pad. This will ensure good RF ground and low

thermal impedance. Maximizing the copper ground plane

will also improve heat spreading and low inductance. It

is a good idea to cover the via holes with solder mask on

the back side of the PCB to prevent solder from wicking

away from the critical PCB to the exposed pad interface.

The DC1774A-B has a nominal working frequency range

from 400MHz to 1000MHz. It is not intended for opera-

tion down to DC. The lower frequency cutoff is limited by

on-chip matching elements.

The generic LTC643X-YY amplifier series demo PCB is

shown in the Schematic Diagram of Figure 6. Hence, the

board can be modified for multiple demo board versions.

For example, both the DC1774A-A and DC1774A-B demo

boards have a differential driver at U1; therefore, the board

is using transformers to transform from differential to

single-ended input and output. Likewise, the DC1774A-C

is a single-ended demo board; consequently, it uses the

LTC6431-15 for single-ended input and output.

SETUP AND TESTING SIGNAL SOURCES

The LTC6430-15 is an amplifier with high linearity perfor-

mance; therefore, output intermodulation products are very

low. For this reason, it drives most test equipment and test

setups to their limits. Consequently, accurate measure-

ment of the third order intercept point for a low distortion

IC such as the LTC6430-15 requires certain precautions

to be observed in the test setup and testing procedure.

Setup Signal Sources

Figure 5 shows a proposed IP3 test setup. This setup has

low phase noise, good reverse isolation, high dynamic

range, sufficient harmonic filtering and wideband imped-

ance matching. The setup is outlined here:

1. High performance signal generators 1 and 2, (HP8644A)

should be used in the setup. These suggested genera-

tors have low harmonic distortion and very low phase

noise.

2. High linearity amplifiers to improve isolation. They

prevent the two signal generators from crosstalking

with each other and provide higher output power.

3. A lowpass filter to suppress harmonic content from

interfering with the test signal.

4. The signal combiner (from Mini-Circuits ADP-2-9),

combines the two isolated input signals. This combiner

has a typical isolation of 27dB. For better VSWR and

isolation, use the H-9 signal combiner from MA/COM

which features >40dB isolation and a wider frequency

range. Passive devices (e.g., combiners) with magnetic

elements can contribute nonlinearity to the signal chain

and should be used cautiously.

5. The attenuator pads, on all three ports of the signal

combiner, will support further isolation of the two input

signal sources. They will reduce reflection and promote

maximum power transfer with wideband impedance

matching.

Testing Signal Sources

The testing signal should be evaluated and optimized before

it is used for measurements. The following outlines the

necessary steps to achieve optimization.

a. Apply two independent signals f1 and f2 from signal

generator 1 and signal generator 2 at 400MHz and

401MHz while setting amplitude = –13dBm per tone

at the combined output.

dc1774a-bf

DEMO MANUAL DC1774A-B

ADDITIONAL INFORMATION

b. Connect the combined signal directly to the spectrum

analyzer (without the DUT).

c. Adjust the spectrum analyzer for the maximum possible

resolution of the Intermodulation products amplitude

in dBc relative to the main tone power. A narrower

resolution bandwidth will take a longer time to sweep.

Optimize the dynamic range of the spectrum analyzer by

adjusting input attenuation. First increase the spectrum

analyzer input attenuation (normally in steps of 5dB

or 10dB). If the IMD product levels decrease when the

input attenuation is increased, then the input power level

was too high for the spectrum analyzer to make a valid

measurement. In other words, the spectrum analyzer’s

1st mixer was overloaded and produced its own IMD

products. If the IMD reading holds constant with in-

creased input attenuation, then a sufficient amount of

attenuation is present. Adding too much attenuation will

raise the noise floor and bury the intended IMD signal.

Therefore, select just enough attenuation to achieve a

stable and valid measurement.

d. In order to achieve a valid measurement result, the

test system must have lower distortion than the DUT

intermodulation. For example, to measure a 47dBm

OIP3, the measured intermodulation products will be

–90dBc below the –13dBm per tone input level and

the test system must have intermodulation products

approximately –96dBc or better. For best results, the

IMD or noise floor should be at least –100dBc before

connecting the DUT.

Testing the DUT

At this point, the input level has been established at –13dBm

per tone, and the input IMD from the test setup is well

suppressed at –96dBm max. Furthermore, the SA is set

up to measure very low level IMD components.

a. Insert the DUT and output attenuator into the setup,

inline between the signal source and SA. The output

attenuator should match the DUT gain.

b. Fine-tune the signal generator levels by a small amount

if necessary (<1dB), to keep output power at 2.0dBm

per tone at the amplifier output.

c. Measure output IMD level using the same optimized

setup as previous. Based on the output power level of

2dBm per tone, and knowing the IMD level, OIP3 can

be calculated.

dc1774a-bf

DEMO MANUAL DC1774A-B

QUICK START PROCEDURE

Demo circuit 1774A-B can be set up to evaluate the per-

formance of the LTC6430-15. Refer to Figures 4 and 5 for

proper equipment connections and follow the procedure

below:

Single-Tone Measurement

Connect all test equipment as suggested in Figure 4.

1. The power labels of 5V and GND directly correspond

to the power supply. Typical current consumption of

the LTC6430-15 is about 160mA.

2. Apply an input signal to J7. A low distortion, low noise

signal source with an external high order lowpass filter

will yield the best performance. The input C.W. signal

is –10dBm.

3. Observe the output via J8. The measured power at the

analyzer should be about 5dBm.

Tw o -Tone Measurement

Connect all test equipment as suggested in Figure 5.

1. The power labels of 5V and GND directly correspond

to the power supply. Typical current consumption of

the LTC6430-15 is about 160mA.

2. Apply two independent signals f1 and f2 from SG1 and

SG2 at 400MHz and 401MHz respectively.

3. Monitor the output tone level on the spectrum analyzer.

Adjust signal generator levels such that output power

measures 2dBm/tone at the amplifier output J8, after

correcting for external cable losses and attenuations.

4. Change the spectrum analyzer’s center frequency and

observe the two IM3 tones at 1MHz below and above

the input frequencies. The frequencies of IM3_LOW,

and IM3_HIGH are 399MHz and 402MHz, respectively.

For this setup, the Rohde & Schwarz FSEM30 spectrum

analyzer was used. This SA has a typical 20dBm third

order intercept point (TOI). The Rohde & Schwarz FSU

can also be used. The system as described can measure

OIP3 up to 50dBm.

dc1774a-bf

DEMO MANUAL DC1774A-B

QUICK START PROCEDURE

Figure 4. Proper Equipment Setup for Gain and Single-Tone Measurement

Figure 5. Proper Equipment Setup for IP3 Measurement

3dB

ATTN. PAD

(OPT)

COAXIAL

CABLE ROHDE & SCHWARZ

FSEM30

(HP8644A)

LOWPASS

FILTER

(OPT)

SIGNAL

GENERATOR

SPECTRUM

ANALYZER

DC POWER SUPPLY

GND V+

ASSY

-A

-B

-C

LTC6430AIUF-15

LTC6431AIUF-15

FREQUENCY

100MHz TO 300MHz

400MHz TO 1000MHz

100MHz TO 1200MHz

VCC = 4.75V TO 5.25V

3dB

ATTN. PAD

6dB ATTN. PAD

(OPT)

6dB ATTN. PAD

(OPT)

15dB

ATTN. PAD

(MATCHES

DUT GAIN)

COAXIAL

CABLE

ROHDE & SCHWARZ

FSEM30

(HP8644A)

LOWPASS

FILTER

AMPLIFIER

MINI-CIRCUITS ZHL-2

OR EQUIVALENT

LOWPASS

FILTER

APPROX.

–13dBm/TONE

2dBm/TONE

DUT GAIN

APPROX. 15dB

SIGNAL

GENERATOR 1

(HP8644A)

SIGNAL

GENERATOR 2

SPECTRUM

ANALYZER

DC POWER SUPPLY

GND V+

VCC = 4.75V TO 5.25V

AMPLIFIER

MINI-CIRCUITS ZHL-2

OR EQUIVALENT

COMBINER

MINI-CIRCUITS

ADP-2-9

ASSY

-A

-B

-C

LTC6430AIUF-15

LTC6431AIUF-15

FREQUENCY

100MHz TO 300MHz

400MHz TO 1000MHz

100MHz TO 1200MHz

dc1774a-bf

DEMO MANUAL DC1774A-B

PARTS LIST

ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER

1 4 C1, C3, C7, C20 CAP., X7R, 1000pF, 50V 5%, 0402 AVX, 04025C102JAT2A

2 1 C21 CAP., X7R, 1000pF, 50V 5%, 0603 AVX, 06035C102JAT2A

3 1 C8 CAP., COG, 62pF, 16V 2%, 0402 AVX, 0402YA620GAT2A

4 0 C10, C12 CAP., COG, 62pF, 16V 2%, 0402 OPT

5 0 C11, C13, C16-C19 CAP., X7R, 1000pF, 5%, 0402 OPT

6 1 C22 CAP., X5R, 0.1µF, 10V, 10%, 0603 AVX, 0603ZD104KAT2A

72 E3, E6 TESTPOINT, TURRET, 0.064" MILL-MAX, 2308-2-00-80-00-00-07-0

8 0 JP1 HEADER, 2X6, 0.1" OPT

9 0 JP2, JP3 HEADER, 2X4, 0.1" OPT

10 0 J5, J6 CONN., SMA 50Ω EDGE-MOUNTED OPT

11 1 J7 CONN., SMA 50Ω EDGE-MOUNTED JOHNSON, 142-0701-851

12 0 J9 CONN., SMA 50Ω EDGE-MOUNTED OPT

13 2 J11, J18 JACK, BANANA KEYSTONE, 575-4

14 1 L1 INDUCTOR, CHIP, 560nH, 5%, 0603LS-1608 COILCRAFT, 0603LS-561XJLB

15 0 L11, L22 INDUCTOR, CHIP, 1008LS-2520 OPT

16 1 R2 RES., CHIP, 348Ω, 1%, 0402 YAGEO, RC0402FR-07348RL

17 0 R5, R6 RES., CHIP, 348Ω, 1%, 0402 OPT

18 0 R19 RES., CHIP, 0Ω, 5%, 0402 YAGEO, RC0402JR-070RL

1 1 DC1774A-2 GENERAL BOM

2 2 C2, C4 CAP., X7R, 1000pF, 50V 5%, 0402 AVX, 04025C102JAT2A

3 1 C5 CAP., X7R, 1000pF, 50V 5%, 0603 AVX, 06035C102JAT2A

4 1 C9 CAP., COG, 62pF, 16V 2%, 0402 AVX, 0402YA620GAT2A

5 0 C14, C15 CAP., X7R, 1000pF, 25V 5%, 0402 AVX, 04023C102JAT2A

6 1 C23 CAP., X5R, 0.1µF, 10V, 10%, 0603 AVX, 0603ZD104KAT2A

7 1 L2 INDUCTOR, CHIP, 560nH, 5%, 0603LS-1608 COILCRAFT, 0603LS-561XJLB

81 J8 CONN., SMA 50Ω EDGE-MOUNTED JOHNSON, 142-0701-851

9 0 J10 CONN., SMA 50Ω EDGE-MOUNTED OPT

10 1 R1 RES., CHIP, 348Ω, 1%, 0402 YAGEO, RC0402FR-07348RL

11 2 R3, R4 RES., CHIP, 0Ω, 1/16W, 5%, 0603 YAGEO, RC0603JR-070RL

12 0 R13, R14, R17, R18 RES., CHIP, 0Ω, 1/16W, 5%, 0603 OPT

13 0 T1, T2 XFMR, MINI-CIRCUITS, ADTL2-18+ OPT

14 2 T3, T4 XFMR, 2:1 MINI CIRCUITS, ADTL2-18+

15 1 U1 IC, IF AMP., QFN24UF-4X4 LINEAR TECH., LTC6430AIUF-15

dc1774a-bf

DEMO MANUAL DC1774A-B

Information furnished by Linear Technology Corporation is believed to be accurate and reliable.

However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-

tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.

Figure 6. DC1774A RF/IF AMP/ADC Driver

SCHEMATIC DIAGRAM

dc1774a-bf

DEMO MANUAL DC1774A-B

Linear Technology Corporation

1630 McCarthy Blvd., Milpitas, CA 95035-7417

(408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com

 LINEAR TECHNOLOGY CORPORATION 2013

LT 0113 • PRINTED IN USA

DEMONSTRATION BOARD IMPORTANT NOTICE

Linear Technology Corporation (LT C ) provides the enclosed product(s) under the following AS IS conditions:

This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT

OR EVALUATION PURPOSES ONLY and is not provided by LT C for commercial use. As such, the DEMO BOARD herein may not be complete

in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety

measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union

directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.

If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date

of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU

OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS

FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR

ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LT C from all claims

arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all

appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or

agency certified (FCC, UL, CE, etc.).

No License is granted under any patent right or other intellectual property whatsoever. LT C assumes no liability for applications assistance,

customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.

LT C currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.

Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and

observe good laboratory practice standards. Common sense is encouraged.

This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LT C applica-

tion engineer.

Mailing Address:

Linear Technology

1630 McCarthy Blvd.

Milpitas, CA 95035