Q45VR3 Series Sensors
Universal voltage photoelectric sensors with electromechanical relay output
Printed in USA 12/12 P/N 53997 rev. C
* 9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., Q453E W/30)
A model with a QD connector requires a mating cable; see page 10.
Q45VR3 Series Features
• Advanced one-piece photoelectric sensors with outstanding optical perform-
ance and extremely rugged design
• Universal supply voltage: 12 to 250V dc or 24 to 250V ac
• Electromechanical relay for economical, high-capacity switching and immunity
to electrical noise
• Full line includes opposed, diffuse, retroreflective, convergent, and glass and
plastic fiber optic sensing modes
• Switchable light/dark operate
• Versatile plug-in modules available for output timing logic and/or signal
strength display
• Highly visible Power, Signal (AID™ System), and Output indicator LEDs
• Choice of prewired 2 m (6.5') or 9 m (30') unterminated cable or Mini-style
quick-disconnect fitting
• Versatile mounting options
• Designed to withstand 1200 psi washdown; exceeds its NEMA 6P and IEC IP67
rating
IMPORTANT: SEE SAFETY USE WARNING ON BACK PAGE
Q45VR3 Series Opposed-Mode Emitter (E) and Receiver (R) Models
Q453E Emitter
Q45VR3R Receiver
Models Range Cable* Supply
Voltage
Output
Type Excess Gain
60 m
(200')
2-wire
2m (6.5')
5-wire
2m (6.5') Universal
12 - 250V dc
or
24 - 250V ac
SPDT
Electro-
mechanical
Relay
Because of their extremely high excess gain, these opposed-mode sensors are an
excellent option for sensing in contaminated or dirty areas, and are also the best
choice for long-range sensing. Infrared, 880 nm
Q453EQ Emitter
Q45VR3RQ Receiver
3-Pin Mini-
style QD
5-Pin Mini-
style QD
Beam Pattern
1
10
100
1.0 m
3.3 ft
10 m
33 ft
100 m
330 ft
0.1 m
0.33 ft
E
X
C
E
S
S
G
A
I
N
DISTANCE
1000
Q45E/R
Opposed Mode
48 m
160 ft
60 m
200 ft
36 m
120 ft
24 m
80 ft
12 m
40 ft
0
0
0.5 m
1.0 m
1.5 m
0.5 m
1.0 m
1.5 m
0
20 in
40 in
60 in
20 in
40 in
60 in
DISTANCE
Q45E/R
Opposed Mode
Effective Beam: 13 mm
Q45VR3 Series
page 2
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
* 9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., Q45VR3LV W/30)
A model with a QD connector requires a mating cable; see page 10.
Models Range Cable*
Supply
Voltage
Output
Type Excess Gain Beam Pattern
Non-Polarized
1
10
100
1000
.10 m
.33 ft
1.0 m
3.3 ft
10 m
33 ft
.01 m
.033 ft
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45LV
Retroreflective Mode
With BRT-3 Reflector
12 m
40 ft
15 m
50 ft
9 m
30 ft
6 m
20 ft
3 m
10 ft
0
0
25 mm
50 mm
75 mm
25 mm
50 mm
75 mm
0
1.0 in
2.0 in
3.0 in
1.0 in
2.0 in
3.0 in
DISTANCE
Q45LV
Retroreflective Mode
With BRT-3 Reflector
Polarized
1
10
100
1000
.10 m
.33 ft
1.0 m
3.3 ft
10 m
33 ft
.01 m
.033 ft
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45LP
Retroreflective Mode
With BRT-3 Reflector
6 m
20 ft
7.5 m
25 ft
4.5 m
15 ft
3 m
10 ft
1.5 m
5 ft
0
0
25 mm
50 mm
75 mm
25 mm
50 mm
75 mm
0
1.0 in
2.0 in
3.0 in
1.0 in
2.0 in
3.0 in
DISTANCE
Q45LP
Retroreflective
Mode
With BRT-3 Reflector
Q45VR3LP
Q45VR3LPQ
0.15 to 6 m
(6" to 20')
Q45VR3LV
Q45VR3LVQ
5-wire
2 m (6.5')
5-Pin
Mini-style QD
Universal
12 - 250V dc
or
24 - 250V ac
SPDT
Electro-
mechanical
Relay
0.08 to 9 m
(3" to 30')
5-wire
2 m (6.5')
5-Pin
Mini-style QD
Universal
12 - 250V dc
or
24 - 250V ac
SPDT
Electro-
mechanical
Relay
Q45VR3 Series Retroreflective-Mode Models
The visible red sensing beam of these sensors makes them very easy to align.
Model Q45VR3LP polarizes the emitted light and filters out unwanted reflections,
making sensing possible in applications otherwise considered unsuited to
retroreflective sensing performance. Specified using the model BRT-3 3" reflector
(see the Accessories section of your current Banner Photoelectric Sensors catalog
for further information). Visible red, 680 nm
Non-Polarized Polarized
P
Q45VR3 Series
page 3
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Q45VR3 Series Diffuse-Mode Models
500 mm
20.0 in
400 mm
16.0 in
300 mm
12.0 in
200mm
8.0 in
100 mm
4.0 in
0
0
5 mm
10 mm
15 mm
5 mm
10 mm
15 mm
0
0.2 in
0.4 in
0.6 in
0.2 in
0.4 in
0.6 in
DISTANCE
Q45D
Diffuse Mode
Models Range Cable*
Supply
Voltage
Output
Type
Excess Gain Beam Pattern
Short Range
Q45VR3DL
Q45VR3DLQ
1. 8 m
(6')
5-wire
2 m (6.5')
5-Pin
Mini-style QD
Universal
12 - 250V dc
or
24 - 250V ac
1
10
100
10 mm
0.4 in
100 mm
4.0 in
1000 mm
40 in
1.0 mm
0.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45D
Diffuse Mode
2.4 m
8 ft
3.0 m
10 ft
1.8 m
6 ft
1.2 m
4 ft
0.6 m
2 ft
0
0
25 mm
50 mm
75 mm
25 mm
50 mm
75 mm
0
1.0 in
2.0 in
3.0 in
1.0 in
2.0 in
3.0 in
DISTANCE
Q45DL
Diffuse Mode
Long Range
Q45VR3DX
Q45VR3DXQ
3 m
(10')
5-wire
2 m (6.5')
5-Pin
Mini-style QD
1
10
100
1000
.10 m
.33 ft
1.0 m
3.3 ft
10 m
33 ft
.01 m
.033 ft
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45DL
Diffuse Mode
Q45VR3D
Q45VR3DQ
45 cm
(18")
5-wire
2 m (6.5')
5-Pin
Mini-style QD
Universal
12 - 250V dc
or
24 - 250V ac
SPDT
Electro-
mechanical
Relay
Performance based on 90% reflectance white test card
SPDT
Electro-
mechanical
Relay
Universal
12 - 250V dc
or
24 - 250V ac
3.0 m
10 ft
2.4 m
8 ft
1.8 m
6 ft
1.2 m
4 ft
0.6 m
2 ft
0
0
25 mm
50 mm
75 mm
25 mm
50 mm
75 mm
0
1.0 in
2.0 in
3.0 in
1.0 in
2.0 in
3.0 in
DISTANCE
Diffuse Mode
Q45DX
High Power
1
10
100
0.1 m
0.33 ft
1.0 m
3.3 ft
10 m
33 ft
0.01 m
0.033 ft
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45DX
Diffuse Mode
SPDT
Electro-
mechanical
Relay
Infrared, 880 nm
These diffuse-mode models detect objects by sensing the reflection of their own emitted light.
Ideal for use when the reflectivity and profile of the object to be sensed are sufficient to return a
large percentage of emitted light back to the sensor. Model Q45VR3DX is the first choice for dif-
fuse-mode applications when there are no background objects to falsely return light.
Q45VR3 Series
page 4
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
* 9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., Q45VR3CV W/30)
A model with a QD connector requires a mating cable; see page 10.
Visible red, 680 nm
These sensors are ideal for reflective sensing of very small parts or profiles, and can accurately
sense the position of parts approaching from the side. Will ignore all but highly reflective objects
that are outside the sensing range.
Q45VR3 Series Convergent-Mode Models
190 mm
7.5 in
150 mm
6.0 in
113 mm
4.5 in
75 mm
3.0 in
38 mm
1.5 in
0
0
1.2 mm
2.5 mm
3.8 mm
1.2 mm
2.5 mm
3.8 mm
0
0.05 in
0.10 in
0.15 in
0.05 in
0.10 in
0.15 in
DISTANCE
Q45CV
Convergent Mode
Models Focus Cable*
Supply
Voltage
Output
Type
Excess Gain Beam Pattern
Q45VR3CV
Q45VR3CVQ
38 mm
(1.5")
Spot Size
at Focus:
1.3 mm
(0.05")
5-wire
2 m (6.5')
5-Pin
Mini-style QD
Universal
12 - 250V dc
or
24 - 250V ac
SPDT
Electro-
mechanical
Relay
1
10
100
10 mm
.4 in
100 mm
4 in
1000 mm
40 in
1 mm
.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45CV
Convergent Mode
190 mm
7.5 in
150 mm
6.0 in
113 mm
4.5 in
75 mm
3.0 in
38 mm
1.5 in
0
0
1.2 mm
2.5 mm
3.8 mm
1.2 mm
2.5 mm
3.8 mm
0
0.05 in
0.10 in
0.15 in
0.05 in
0.10 in
0.15 in
DISTANCE
Q45CV4
Convergent Mode
Q45VR3CV4
Q45VR3CV4Q
100 mm
(4")
Spot Size
at Focus:
1.5 mm
(0.06")
5-wire
2 m (6.5')
5-Pin
Mini-style QD
Universal
12 - 250V dc
or
24 - 250V ac
SPDT
Electro-
mechanical
Relay
1
10
100
10 mm
.4 in
100 mm
4 in
1000 mm
40 in
1 mm
.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45CV4
Convergent Mode
Performance based on 90% reflectance white test card
1
10
100
10 mm
0.4 in
100 mm
4 in
1000 mm
40 in
1.0 mm
0.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45FV
Opposed Mode
IT23S fibers
IT13S fibers
300 mm
12 in
250 mm
10 in
200 mm
8 in
150 mm
6 in
100 mm
4 in
0
0
10 mm
20 mm
30 mm
10 mm
20 mm
30 mm
0
0.4 in
0.8 in
1.2 in
0.4 in
0.8 in
1.2 in
DISTANCE
Q45FV
Opposed Mode
IT23S Fibers
IT13S Fibers
2.0 m
75 in
1.6 m
60 in
1.2 m
45 in
0.8 m
30 in
0.4 m
15 in
0
0
50 mm
100 mm
150 mm
50 mm
100 mm
150 mm
0
2.0 in
4.0 in
6.0 in
2.0 in
4.0 in
6.0 in
DISTANCE
Q45F
Opposed Mode
IT23S Fibers
IT13S Fibers
BP Q45F opp.eps
page 5
Q45VR3 Series
These models are an excellent choice for glass fiber optic applications where
faster sensor response is not important. Their high excess gain means that
opposed individual fibers can operate reliably in many very hostile environments.
Also, special miniature bifurcated fiber optic assemblies with bundle sizes as
small as 0.5 mm (.020") dia. may be used successfully for diffuse-mode sensing
when using sensor model Q45VR3F(Q). For more information on compatible
glass fiber optics, refer to your current Banner Photoelectric Sensors catalog.
Q45VR3 Series Glass Fiber-Optic Models
Models Range Cable*
Supply
Voltage
Output
Type
Excess Gain Beam Pattern
Infrared, 880 nm
1
10
100
0.1 m
0.33 ft
1.0 m
3.3 ft
10 m
33 ft
0.01 m
0.03 ft
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45F
Opposed Mode
IT23S fibers
IT13S fibers
Diffuse mode performance based on 90% reflectance white test card
Q45VR3F
Q45VR3FQ
Range
varies by
sensing
mode and
fiber optics
used
5-wire
2 m (6.5')
5-Pin
Mini-style QD
Universal
12 - 250V dc
or
24 - 250V ac
SPDT
Electro-
mechanical
Relay
Infrared, 880 nm and Visible Red, 650 nm
Q45VR3FV
Q45VR3FVQ
Range
varies by
sensing
mode and
fiber optics
used
5-wire
2 m (6.5')
5-Pin
Mini-style QD
Universal
12 - 250V dc
or
24 - 250V ac
SPDT
Electro-
mechanical
Relay
Visible Red, 650 nm
1
10
100
10 mm
0.4 in
100 mm
4.0 in
1000 mm
40 in
1 mm
0.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45F
Diffuse Mode
BT23S Fiber
BT13S Fiber
125 mm
5 in
100 mm
4 in
75 mm
3 in
50 mm
2 in
25 mm
1 in
0
0
1.3 mm
2.5 mm
3.8 mm
1.3 mm
2.5 mm
3.8 mm
0
0.05 in
0.10 in
0.15 in
0.05 in
0.10 in
0.15 in
DISTANCE
Q45F
Diffuse Mode
BT23S Fiber
BT13S Fiber
1
10
100
10 mm
0.4 in
100 mm
4.0 in
1000 mm
40 in
1 mm
0.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45FV
Diffuse Mode
BT23S Fiber
BT13S
Fiber
25 mm
1.0 in
20 mm
0.8 in
15 mm
0.6 in
10 mm
0.4 in
5 mm
0.2 in
0
0
1.0 mm
2.0 mm
3.0 mm
1.0 mm
2.0 mm
3.0 mm
0
0.04 in
0.08 in
0.12 in
0.04 in
0.08 in
0.12 in
DISTANCE
Q45FV
Diffuse Mode
BT23S Fiber
BT13S Fiber
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Q45VR3 Series
page 6
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
* 9 m (30') cables are available by adding suffix “W/30” to the model number of any cabled sensor (e.g., Q45VR3FP W/30)
A model with a QD connector requires a mating cable; see page 10.
Visible red, 660 nm
Lower in cost than glass fiber optics, plastic fiber optics are ideal for use in situ-
ations where environmental conditions allow (for example, low levels of acids,
alkalis, and solvents). Most are easily cut to length in the field, and are available
in a variety of sensing end styles. For more information on compatible plastic
fiber optics, refer to your current Banner Photoelectric Sensors catalog.
Q45VR3 Series Plastic Fiber-Optic Models
Models Range Cable*
Supply
Voltage
Output
Type
Excess Gain Beam Pattern
Q45VR3FP
Q45VR3FPQ
1
10
100
10 mm
0.4 in
100 mm
4.0 in
1000 mm
40 in
1 mm
0.04 in
1000
E
X
C
E
S
S
G
A
I
N
DISTANCE
Q45FP
Opposed Mode
PIT46U Fibers
PIT26U Fibers
125 mm
5.0 in
100 mm
4.0 in
75 mm
3.0 in
50 mm
2.0 in
25 mm
1.0 in
0
0
15 mm
30 mm
45 mm
15 mm
30 mm
45 mm
0
0.6 in
1.2 in
1.8 in
0.6 in
1.2 in
1.8 in
DISTANCE
Q45FP
Opposed Mode PIT46U Fibers
PIT26U Fibers
Diffuse mode performance based on 90% reflectance white test card
Range
varies by
sensing
mode and
fiber optics
used
5-wire
2 m (6.5')
5-Pin
Mini-style QD
Universal
12 - 250V dc
or
24 - 250V ac
SPDT
Electro-
mechanical
Relay
1
10
100
1 mm
0.04 in
10 mm
0.4 in
100 mm
4 in
0.1 mm
0.004 in
1000
E
X
C
E
S
S
G
A
I
N
Q45FP
Diffuse Mode
PBT46U Fiber
PBT26U Fiber 50 mm
2.0 in
40 mm
1.6 in
30 mm
1.2 in
20 mm
0.8 in
10 mm
0.4 in
0
0
6 mm
1
2 mm
1
8 mm
6 mm
1
2 mm
1
8 mm
0
0.25 in
0.50 in
0.75 in
0.25 in
0.50 in
0.75 in
DISTANCE
Q45FP
Diffuse Mode
PBT46U Fiber
Q45VR3 Series
page 7
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Q45VR3 Series Specifications
Supply Voltage and Current Universal voltage: 24 to 250V ac, 50/60 Hz or 12 to 250V dc (1.5 watts maximum)
Supply Protection Circuitry Protected against transient voltages. DC hookup is without regard to polarity.
Output Configuration SPDT (Single-Pole, Double-Throw) electromechanical relay output. All models except emitters.
Output Rating Max. switching power (resistive load): 1250VA, 150W
Max. switching voltage (resistive load): 250V ac, 125V dc
Max. switching current (resistive load): 5A @ 250V ac, 5A @ 30V dc derated to 200 mA @ 125V dc
Min. voltage and current: 5V dc, 10mA
Mechanical life of relay: 50,000,000 operations
Electrical life of relay at full resistive load: 100,000 operations
Output Protection Circuitry Protected against false pulse on power-up
Output Response Time 15 milliseconds ON and OFF
(NOTE: 100 millisecond delay on power-up. Relay is de-energized during this time.)
Repeatability Opposed mode: 0.25 milliseconds
All other sensing modes: 0.5 milliseconds
Response time and repeatability specifications are independent of signal strength.
Adjustments Light/Dark Operate select switch; and multi-turn Sensitivity control on top of sensor beneath a transparent
o-ring-sealed Lexan®cover, allows precise sensitivity setting (turn clockwise to increase gain). Optional logic
and logic/display modules have adjustable timing functions (see page 10).
Indicators Indicator LEDs are clearly visible beneath a raised transparent Lexan®dome on top of the sensor.
Power (green) LED lights whenever 24 to 250V ac, or 12 to 250V dc power is applied
Signal (red) AID™ System LED lights whenever the sensor sees its modulated light source, and pulses at a
rate proportional to the strength of the received light signal
Load (yellow) LED lights whenever the output relay is energized
Optional 7-element LED signal strength display module
Construction Molded reinforced thermoplastic polyester housing, o-ring-sealed transparent Lexan®cover, molded acrylic
lenses, and stainless steel hardware. Q45s are designed to withstand 1200 psi washdown. The base of
cabled models has a 1/2" NPS integral internal conduit thread.
Environmental Rating NEMA 6P, IEC IP67
Connections PVC-jacketed 2 m (6.5') or 9 m (30') unterminated cables, or Mini-style quick-disconnect (QD) fittings are
available (“Q”- suffix models). QD cables are ordered separately. See page 10.
Operating Conditions Temperature: -25° to +55° C (-13° to +131°F)
Maximum relative humidity: 90% at 50°C (non-condensing)
Application Notes Transient suppression is recommended for contacts switching inductive loads.
Optional output timing modules are available. See page 10 for more information.
Lexan®is a registered trademark of General Electric Co.
Certifications
Q45VR3 Series
page 8
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Q45VR3 Series Dimensions
54.1 mm*
(2.13")
44.5 mm
(1.75")
69.0 mm
(2.72")
87.6 mm
(3.45")
Internal Thread
(1/2–14NPSM)
External Thread
M30 X 1.5
30.0 mm
(1.18")
ø 6.1 (0.24")
2m (6.5') Cable
7.1 mm
(0.28")
4.5 mm (#10) Screw
Clearance (2)
50.8 mm
(2.00")
6.4 mm (0.25")
Lens Centerline
Mounting Nut is Supplied
*57.9 mm (2.28") for LP models
Q45VR3 Series Sensors – Opposed, Retro, and Diffuse Sensing Modes
(model suffix E, R, D, DL, DX, LP & LV)
Convergent Sensing Mode
(model suffix CV & CV4)
Glass Fiber Optic
(model suffix F and FV)
Cabled
87.6 mm
(3.45")
External Thread
M30 X 1.5
Mini-style QD Connector
14 mm (0.6")
61.7 mm
(2.43")
50.8 mm
(2.00")
Lens
Centerline
60.5 mm
(2.38")
59.8 mm
(2.35")
Quick-Disconnect
Plastic Fiber Optic
(model suffix FP)
Q45VR3 Series
page 9
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Q45VR3 Series Indicators and Controls
Status indicator LEDs for Power, Signal and Output are clearly visible
beneath a raised dome in the sensor’s transparent o-ring-sealed Lexan®
cover. The Power indicator lights whenever power is applied to the sensor.
The Signal LED lights whenever the sensor sees its modulated light
source, and pulses at a rate proportional to the strength of the received
light signal; this is the AID™ Alignment Indicating Device*. The Output
indicator lights whenever the sensor’s output relay is energized. This indi-
cator is especially useful when a timing logic module is used and Signal
and Output conditions are not concurrent.
Also located beneath the sensor’s o-ring-sealed cover are controls for
light/dark operate selection and Sensitivity adjustment.
* US patent no. 4356393
Figure 1. Indicators and controls on the Q45VR3 Series
Sensors
Q45VR3 Sensors with Attached Cable Q45VR3 Sensors with Quick-Disconnect
5-Pin Mini-Style ( model suffix Q)
Q453E Emitters with Attached Cable Q453EQ Emitters with Quick-Disconnect
3-Pin Mini-Style
bu
ye
wh NC
C
NO
bn
bk
24 - 250V ac or 12 - 250V dc*
NC
C
NO
bu
ye
wh
bn
bk
24 - 250V ac or 12 - 250V dc*
bn
bu
24-250V ac or 12-250V dc*
bn
bk
bu 24-250V ac or 12-250V dc*
Q45VR3 Series Hookups
*NOTE: Connection of dc power is without regard to polarity.
Quick-Disconnect (QD) Option
AC Q45VR3 Series sensors are sold with either a 2 m (6.5') or a 9 m (30') attached PVC-covered cable, or with a 3-pin Mini-
style (opposed mode emitter) or 5-pin Mini-style Quick-Disconnect (QD) cable fitting.
Mini-style QD sensors are identified by the suffix “Q” in their model number suffix. Mating cables for QD Q45VR3 sensors are
specified on page 10.
Q45VR3 Series
page 10
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Mini-Style Quick-Disconnect Cables
Cable: PVC jacket, polyurethane connector body, nylon coupling nut
Conductors: 18 AWG high-flex stranded, PVC insulation, gold plated contacts
Temperature: -40° to +80°C (-40 to +176°F)
Voltage Rating: 250V ac/300V dc
Black Wire
Blue Wire
Brown Wire
Yellow Wire
White Wire
3-Pin
Female
Pin-out
Straight
MBCC-306
MBCC-312
MBCC-330
2 m (6.5')
4 m (12')
9 m (30')
7/8-16UN-2B
ø28 mm max.
(1.1")
61 mm max.
(2.4")
5-Pin
Female
Pin-out
Straight
Style
MBCC-506
MBCC-512
MBCC-530
Brown Wire
Blue Wire
Black Wire
2 m (6.5')
4 m (12')
9 m (30')
Model Length Dimensions Pin-Out (Female View)
Accessories
Retroreflective Targets
Banner offers a wide selection of high-qualitity retroreflective targets. See the Accessories
section of your current Banner Photoelectric Sensors catalog for complete information.
NOTE: Polarized sensors require corner cube type retroreflective targets only. Non-polarized
sensors may use any retroreflective target.
45LM58
45LM58D
45LMD
Programmable output timing logic
Programmable output timing logic plus signal strength display
Signal strength display only (no timing function)
Q45 sensors easily accept the addition of output timing logic and signal strength display functions. Display modules have a seven-element dis-
play which gives a “finer” indication of excess gain than does the AID™ system LED that is standard on Q45 sensors. The modules listed
below may be used with all Q45VR3 sensors. See the data sheet packed with the module for more information.
Model Logic and/or Display Function
Output Timing Logic and Signal Strength Display Modules
Q45VR3 Series
page 11
Banner Engineering Corp. • Minneapolis, U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Mounting Brackets
Model Description Dimensions
56.0 mm
(2.20")
63.0 mm
(2.48")
13.5 mm (0.53")
45.0 mm
(1.77")
2.5 mm
(0.10")
31.5 mm
(1.24")
Nut Plate
13 mm
(0.5")
M5 x 0.8 x 80 mm
Screw (2)
SMB30C • 30 mm split clamp, black PBT bracket
• Stainless steel mounting hardware included
50.8 mm
(2.00")
58.7 mm
(2.31")
66.5 mm
(2.62")
30.0 mm
(1.18")
29.0 mm
(1.14")
12.7 mm
(0.50")
SMB30SC • 30 mm swivel, black PBT bracket
• Stainless steel mounting hardware included
57.2 mm
(2.25")
57.2 mm
(2.25")
34.9 mm
(1.38")
ø 6.4 mm
(0.25" dia.)
ø 30.15 mm
(1.187" dia.)
25.4 mm
(1.00")
35.1 mm
(1.38")
25.4 mm
(1.00") ø 5.1 mm
(0.20" dia.)
25.4 mm
(1.00")
6.4 mm
(0.25")
25.4 mm
(1.00")
57.0 mm
(2.25")
69.9 mm
(2.75")
7.1 mm
.28 x 90° (2 Slots)
R 25.4 mm
(1.00")
SMB30MM
• 30 mm, 11-gauge, stainless steel bracket
with curved mounting slots for versatility
and orientation
• Clearance for M6 (1/4") hardware
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 • Phone: 763.544.3164 • www.bannerengineering.com • E-mail: sensors@baneng.com
Q45VR3 Series
WARNING . . . Not To Be Used for Personnel Protection
Never use these products as sensing devices for personnel protection. Doing so could lead to serious injury or death.
These sensors do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applica-
tions. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Consult your current Banner
Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection.
!
Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year
following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its
manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty
period.This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of
the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR
IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEAL-
ING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO
EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR
ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR
SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE
THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY,
NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming
any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp.
:DUUDQW\
