EM2696AV63HR2S1XX - CARLO GAVAZZI

Specifications are subject to change without notice EM2696 DS ENG 261012 1

•Class 1 (kWh) according to EN62053-21

•Class B (kWh) according to EN50470-3

•Class 2 (kvarh) according to EN62053-23

•Accuracy ±0.5% RDG (current/voltage)

•Dual colour backlight: no backlight, blue or white (selectable)

•Energy analyzer

•Instantaneous variables readout: 4 DGT

•Energies/gas/water readout: 8 DGT

•

System variables: VLL, VLN, Admd, VA, VAdmd, VAdmd max, W,

Wdmd, Wdmd max, var, PF, Hz, Phase-sequence.

•Single phase variables: VLL, VLN, A, VA, W, var, PF

•Energy measurements: total and partial kWh and kvarh or

based on 4 different tariffs; single phase measurements

•Gas, cold water, hot water, kWh

remote heating

measurements

•Hour counter (6+2 DGT)

•Harmonic analysis (FFT) up to 15th harmonic (current/voltage)

•TRMS measurements of distorted sine waves (voltages/currents)

•Universal power supply: 90 to 260AC/VDC

•

3digital inputs for tariff selection, DMD synch or gas/water (hot-

cold) and remote heating metering (on request)

•3digital outputs for pulses or for alarms or as a mix of them

(on request)

•Front dimensions: 96x96mm

•Protection degree (front): IP50

•RS485 serial output (on request) (MODBUS-RTU), iFIX SCADA

compatibility

Product Description

Three-phase energy analyzer

with built-in configuration joy-

stick and LCD data displaying;

particularly indicated for active

and reactive energy metering

•M-bus communication by means of VMU-B adapter

•Application adaptable display and programming

procedure (Easyprog function)

•Easy connections management

•Certified according to MID Directive (option PF only):

see “how to order” below

•Other versions available (not certified, option XX):

see “how to order” on the next page

and for cost allocation. Housing

for panel mounting with IP50

(front) protection degree. Exter-

nal Current and potential trans-

formers connection. Moreover

Model

Range code

System

Power supply

Input/Output

Communication

Options

Measurement

How to order

EM26 96 AV5 3 H O3 S1 PF A

Type Selection

Range codes

AV5: 230 VLN/400VLL

1/5(10)A

VLN : 160 V to 480 VLN

VLL : 277 V to 830 VLL

AV6: 120 VLN/208VLL

1/5(10)A

VLN :40 V to 144 VLN

VLL :70 V to 250 VLL

Options

PF:

Certified according to

MID Directive, Annex

"B" + Annex "D" for

legal metrology relevant

to active electrical

energy meters (see

Annex MI-003 of MID).

Can be used for fiscal

(legal) metrology.

System

3: 3-phase, 4-wire;

Input/Output

O1: single open collector type

(pulse or alarm)

O3: 3open collector type

(mixed combination of

pulse, alarm and/or

remote output)

R2: dual relay type (functions

as per “O3”)

I3: 3digital inputs for tariff

selection or Gas/water/

energy/remote heating

metering

Communication

XX: none

S1: RS485 port

Energy Management

Energy Analyzer

Type EM26 96

the meter can be provided with

digital outputs that can be used:

for pulses proportional to the

active and reactive energy being

measured or for alarm outputs,

or for remote control. RS485

communication port and 3 digi-

tal inputs are available as an

option.

Certified according to MID Directive, Annex

"B" + Annex "D" for legal metrology relevant to

active electrical energy meters (see Annex MI-

003 of MID). Can be used for fiscal (legal)

metrology. Only the total positive energy meter is certified

according to MID.

MID

AV5

AV6

3O1

Range

System

Input/Output

Power supply

Option

Communication

NOTE: please check the

availability of the needed

code on the verification path

diagram on left beforeorder.

Measurement

Power supply

H: 90 to 260VAC/DC (48

to 62Hz)

Measurement

A: The power is always

integrated (both in case

of positive and negative

power) and the total

energy meter is certified

according to MID.

B: Only the total positive

energy meter is certified

according to MID. The

negative energy meter

is not certified according

to MID.

2Specifications aresubject to change without notice EM2696 DS ENG 261012

EM26 96

Model

Range code

System

Power supply

Input/Output

Communication

Options

How to order

EM26 96 AV5 3 H O3 S1 XX

Type Selection

Range codes

AV5: 230 VLN/400VLL

1/5(10)A

VLN :160 V to 480 VLN

VLL :277 V to 830 VLL

AV6: 120 VLN/208VLL

1/5(10)A

VLN :40 V to 144 VLN

VLL :70 V to 250 VLL

Options

XX: none

System

3: balanced and

unbalanced load:

3-phase, 4-wire;

3-phase, 3-wire;

2-phase, 3-wire;

1-phase, 2-wire

Input/Output

O1: single open collector

type (pulse or alarm)

O3: 3open collector type

(mixed combination of

pulse, alarm and/or

remote output)

R2: dual relay type (functions

as per “O3”)

I3: 3digital inputs for tariff

selection or Gas/water/

energy/remote heating

metering

Power supply

H: 90 to 260VAC/DC

(48 to 62Hz)

Communication

XX: none

S1: RS485 port

Not certified according to MID directive. Cannot be

used for fiscal (legal) metrology.

STANDARD

AV5

AV6

3O1

HXX

Range

System

Input/Output

Power supply

Option

Communication

NOTE: please check the

availability of the needed

code on the verification path

tables on left beforeorder.

Specifications are subject to change without notice EM2696 DS ENG 261012 3

EM26 96

Rated inputs System type: 3

Current type Galvanic insulation by

means of built-in CT’s

Current range (by CT) AV5 and AV6: 1/5(10)A

Voltage by direct connection

or VT/PT AV5: 230 VLN/400VLL;

AV6: 120 VLN/208VLL

Accuracy (Display + RS485) Ib: see below, Un: see below

(@25°C ±5°C, R.H. ≤60%,

50±5Hz/60±5Hz)

AV5 model In: 5A, Imax: 10A; Un: 160

to 480VLN (277 to 830VLL)

AV6 model In: 5A, Imax: 10A; Un: 40 to

144VLN (70 to 250VLL)

Current

AV5, AV6 models From 0.002In to 0.2In:

±(0.5% RDG +3DGT)

From 0.2In to Imax:

±(0.5% RDG +1DGT).

Phase-neutral voltage In the range Un: ±(0,5%

RDG +1DGT)

Phase-phase voltage In the range Un: ±(1% RDG

+1DGT)

Frequency ±0.1Hz (50±5Hz/60±5Hz)

Active and Apparent power ±(1%RDG +2DGT)

Power Factor ±[0.001+1%(1.000 - “PF

RDG”)]

Reactive power ±(2%RDG +2DGT)

Active Energy Class 1 according to

EN62053-21; class B

according to EN50470-3.

Reactive Energy Class 2 according to

EN62053-23

AV5, AV6 models In: 5A, Imax: 10A;

0.1 In: 0.5A.

Start up current: 10mA

Harmonic distortion THD up to 15th harmonic

±3% reading

Energy additional errors

Influence quantities According to EN62053-21,

EN62053-23

Temperature drift ≤200ppm/°C

Sampling rate 1600 samples/s @ 50Hz

1900 samples/s @ 60Hz

Display refresh time 750 msec

Display 3lines (1 x 8 DGT;

2x4DGT)

Type LCD, h 9.5mm, dual colour

backlight (selectable)

Instantaneous variables read-out 4DGT

Energies Exported: Total

6+1DGT or 7DGT (with “-“

sign).

Imported: 6+2, 7+1 or

8DGT

Overload status EEEE indication when the

value being measured is

exceeding the “Continuous

inputs overload” (maximum

measurement capacity)

Max. and Min. indication Max. instantaneous

variables: 9999; energies:

99 999 999. Min. instanta-

neous variables: 0; ener-

gies 0.00

LEDs Red LED (Energy

consumption), according to

EN50470-3, EN62052-11

0.001 kWh/kvarh by pulse

if CT ratio by VT ratio is ≤7;

0.01 kWh/kvarh by pulse if

CT ratio by VT ratio is > 7.1

≤70.0;

0.1 kWh/kvarh pulse if CT

ratio by VT ratio is > 70.1 ≤

700.0;

1kWh/kvarh by pulse if CT

ratio by VT ratio is > 700.1;

1000 imp./kWh/kvarh.

Max frequency: 16Hz

Measurements See “List of the variables

that can be connected to:”

Method TRMS measurements of

distorted wave forms.

Coupling type By means of external CT’s

Crest factor ≤3(15A max. peak)

Current Overloads

Continuous 10A, @ 50Hz

For 500ms 200A, @ 50Hz

Voltage Overloads

Continuous 1.2 Un

For 500ms 2 Un

Input impedance

208VL-L (AV6) >1MΩ

400VL-L (AV5) >1MΩ

1/5(10) A (AV5-AV6) < 0.3VA

Frequency 50±5Hz/60±5Hz

Joystick For variable selection:

programming of the

instrument working

parameters and Wdmd

max reset

Input specifications

4Specifications aresubject to change without notice EM2696 DS ENG 261012

EM26 96

Relay output

Physical outputs Max. 2

Purpose For alarm output, pulse

output or remote control.

Type Relay, SPST type

AC 1-5A @ 250VAC

DC 12-5A @ 24VDC

AC 15-1.5A @ 250VAC

DC 13-1.5A @ 24VDC

Insulation 4000 VRMS outputs to

measuring input.

4000 VRMS outputs to

power supply input.

RS485

Type Multidrop, bidirectional

(static and dynamic

variables)

Connections 2-wire

Max. distance 1000m

(without amplifier)

Termination directly on the

instrument

Addresses 247, selectable by means

of the front joystick

Protocol MODBUS/JBUS (RTU)

Data (bidirectional)

Dynamic (reading only) System and phase

variables: see table “List of

variables...”

Static (reading and writing) All the configuration

parameters.

Data format 1 start bit, 8 data bit, no

parity,1 stop bit

Baud-rate 4800, 9600 bits/s

Driver input capability 1/5 unit load

Maximum 160 transceivers

on the same bus, which

can be expanded with

signal amplifiers.

Insulation By means of optocouplers,

4000 VRMS output to

measuring input.

4000 VRMS output to

power supply input

Digital outputs

Pulse type

Number of outputs Up to 3, independent.

Programmable from 0.001

to 10.00 kWh/kvarh per

pulse.

Type Outputs connectable to the

energy meters (Wh/varh)

Pulse duration TON selectable (30 ms or

100 ms) according to

EN62053-31

TOFF:≥120ms, according to

EN62052-31

Alarm type

Number of outputs Up to 3, independent

Alarm modes Up alarm, down alarm (see

the table “List of the

variables that can be

connected to”)

Set-point adjustment From 0 to 100% of the

display scale

Hysteresis From 0 to full scale

On-time delay 0to 255s

Output status Selectable: normally

de-energized or normally

energized

Min. response time ≤700ms, filters excluded.

Set-point on-time delay: “0 s”

Remote control The digital ouputs status can

be managed by means of

serial communication RS485,

if programmed as remote.

Note The 3 digital outputs can

also work as a triple pulse

output, triple alarm output,

or in any other combination.

Static output

Physical outputs Max. 3

Purpose For pulse output, alarm

output or remote control.

Signal VON 1.2 VDC/ max. 100 mA

VOFF 30 VDC max.

Insulation By means of optocouplers,

4000 VRMS output to

measuring inputs,

4000 VRMS output to

power supply input.

Output specifications

Number of inputs 3

Input frequency 20Hz max, duty cycle 50%

Prescaler adjustment From 0.001 to 999.9 m3or

kWh/pulse

Contact measuring voltage 5VDC +/- 5%

Contact measuring current 10mA max

Input impedance 680Ω

Contact resistance ≤100Ω,closed contact

≥500kΩ,open contact

Digital input specifications

Working modes Selectable:

•total and partial energy

meters (kWh and kvarh)

managed by time periods

(t1-t2-t3-t4), W dmd

synchronisation (the

synchronisation is made

every time the tariff

changes) and GAS (m3)or

WATER (hot-cold m3)or

Specifications are subject to change without notice EM2696 DS ENG 261012 5

EM26 96

Password Numeric code of max. 4

digits; 2 protection levels

of the programming data:

1st level Password“0”, no protec-

tion;

2nd level Password from 1 to 9999,

all data are protected

System selection

System 3-Pn unbalanced load 3-phase (4-wire);

3-phase (3-wire).

System 3-P 1 balanced load 3-phase (3-wire) one cur-

rent and 3-phase to phase

voltage measurements.

3-phase (4-wire) one cur-

rent and one-phase (L1) to

neutral voltage measure-

ment.

System 2-P 2-phase (3-wire).

System 1-P 1-phase (2-wire).

Transformer ratio

VT (PT) 1.0 to 999.9 / 1000 to

6000.

CT 1.0 to 999.9 / 1000 to 9999

/10.00k to 60.00k.

The maximum power being

measured cannot exceed

210 MW (calculated as

maximum input voltage

and current, see the

“Accuracy” paragraph (on

page 2). The maximum VT

by CT ratio is 48600. If the

currents and/or voltages

being measured exceed

their maximum limits, the

display shows the error

message “EEEE”.

For EN50470-3 compliant

applications the maximum

power being measured is

25 MW.

Filter

Operating range 0to 100% of the input dis-

play scale

Filtering coefficient 1 to 32

Filter action Measurements, serial out-

put (fundamental variables:

V, A, W and their derived

ones).

Displaying Up to 3 variables per page

See « Display pages » 8

different set of variables

available (see « Display

pages ») according to the

application being selected

Alarm highlight In case of alarm and if the

relevant function is

enabled, the display

changes the colour alterna-

tively from white backlight

to blue backlight and vice

versa.

Reset By means of the front

joystick:

-dmd and max. dmd;

-total energies and

gas/water: kWh, kvarh;

-partial energies and

tariffs: kWh, kvarh

Harmonic analysis Up to the 15th harmonics

on single current and

voltage

Software functions

remote heating (kWh)

meters or external kWh

meter;

•total and partial energy

meters (kWh and kvarh)

managed by time periods

(t1-t2), W dmd synchroni-

sation (the synchronisation

is made independently of

the tariff selection) and

GAS (m3)or WATER

(hot-cold m3)or remote

heating (kWh) meters or

external kWh meter;

•total energy (kWh, kvarh)

and GAS, WATER (hot-cold

m3)and remote heating

meters or external kWh

meter, 3 choices only.

Digital input specifications (cont.)

Note The energy metering is

only made by means of the

analogue inputs.

Insulation By means of optocouplers,

4000 VRMS digital inputs

to measuring inputs.

4000 VRMS digital inputs

to power supply input.

6Specifications aresubject to change without notice EM2696 DS ENG 261012

EM26 96

Auxiliary power supply H: 90 to 260VAC/DC

(48 to 62Hz)

Power consumption

AC: 6VA

DC: 3.5 W

Power supply specifications

Immunity to conducted

disturbances 10V/m from 150KHz to

80MHz

Surge On current and voltage

measuring inputs circuit:

4kV;

Radio frequency suppression According to CISPR 22

Standard compliance

Safety IEC60664, IEC61010-1

EN60664, EN61010-1

EN62052-11

Metrology EN62053-21, EN50470-3,

EN62053-23.

Pulse output DIN43864, IEC62053-31

Approvals CE, cULus listed, MID (PF

option only)

Connections Screw-type

Cable cross-section area Max. 1.5 mm2

Housing

Dimensions (WxHxD) 96 x 96 x 63 mm

Material ABS,

self-extinguishing: UL 94 V-0

Mounting Panel mounting

Protection degree

Front IP50

Screw terminals IP20

Weight Approx. 400 g (packing

included)

Operating temperature -25°C to +55°C (-13°F to

131°F) (R.H. from 0 to 90%

non-condensing @ 40°C)

according to EN62053-21

and EN62053-23

Storage temperature -30°Cto +70°C (-22°F to

158°F) (R.H. < 90% non-

condensing @ 40°C)

according to EN62053-21

and EN62053-23

Installation category Cat. III (IEC60664,

EN60664)

Insulation (for 1 minute) 4000 VRMS between mea-

suring inputs and power

supply.

4000 VRMS between power

supply and RS485 digital

outputs

Dielectric strength 4000 VRMS for 1 minute

Noise rejection CMRR 100 dB, 48 to 62 Hz

EMC According to EN62052-11

Electrostatic discharges 15kV air discharge;

Immunity to irradiated Test with current: 10V/m

from 80 to 2000MHz;

Electromagnetic fields Test without any current:

30V/m from 80 to

2000MHz;

Burst On current and voltage

measuring inputs circuit:

4kV

General specifications

Software functions (cont.)

Easy connection function For all the display selections,

both energy and power

measurements are inde-

pendent of the current

direction. The displayed

energy is always “imported”

with the only exception of

“F” and “H” types (see

“display pages” table).

For these latter selections

the energies can be either

“imported” or “exported”

depending on the current

direction.

Specifications are subject to change without notice EM2696 DS ENG 261012 7

EM26 96

Phase variables

Instantaneous effective voltage

Instantaneous active power

Instantaneous power factor

Instantaneous effective current

Instantaneous apparent power

Instantaneous reactive power

Accuracy (according to EN50470-3 and EN62053-23)

kWh,accuracy (RDG) depending on the current

10A (Imax)

5A (In)

0.25A (Itr)

0.05A (Imin)

Accuracy limits (Active energy)

Start-up current: 10mA

kvarh,accuracy (RDG) depending on the current

Accuracy limits (Reactive energy)

Start-up current: 10mA

PF=1

PF=L0.5

or C0.8

10A (Imax)

5A (In)

0.25A

0.5A

0.1A

0.25A

sinϕ=1

sinϕ=0.5

+1%

+1.5%

-1%

-1,5%

+2%

+2,5%

-2%

-2,5%

System variables

Equivalent three-phase voltage

Three-phase reactive power

Three-phase active power

Three-phase apparent power

Three-phase power factor

(TPF)

Used calculation formulas

Energy metering

Where:

P=active power;

Q=reactive power;

t1, t2=starting and ending time points

of consumption recording;

nj=time unit;

∆t=time interval between two succes-

sive power consumptions;

n1, n2=starting and ending discrete

time points of consumption recording

MID “Annex MI-003” compliance (PF option only)

Accuracy 0.9 Un ≤U≤1.1 Un;

0.98 fn ≤f≤1.02 fn;

fn: 50Hz;

cosϕ:0.5 inductive to 0.8

capacitive.

AV5-AV6 models Class B. I st: 0.01A; I min:

0.05A; I tr: 0.25A; I n: 5A;

Imax: 10A

Operating temperature-25°C to +55°C (-13°F to

131°F) (R.H. from 0 to 90%

non-condensing @ 40°C)

EMC compliance E2

Mechanical compliance M2

Protection degree in order to achieve the

protection against dust and

water required by the

norms harmonized to MID,

the meter must be used

only installed in IP51 (or

better) cabinets.

Where: n=sample number

Percentage error limits for class index B

8Specifications aresubject to change without notice EM2696 DS ENG 261012

EM26 96

•RS485 communication port

•Alarm outputs (“max” variable”, “energies” and “hour counter” excluded)

•Pulse outputs (only positive “energies”)

No Variable 1-phase 2-phase 3-ph. 4-wire 3-ph. 4-wire 3 ph. 3-wire 3 ph. 3-wire Notes

system system balanced sys. unbal. sys. bal. sys. unbal. sys.

1 V L-N sys x x x x x sys=system

2VL1 x x x x x x

3 V L2 o x x x x x

4VL3 o o x x x x

5VL-L sys o x x x x x sys=system

6 V L1-2 o x x x x x

7VL2-3 o o x x x x

8 V L3-1 o o x x x x

9 A dmd max x x x x x Highest “dmd”

current among

the phases (1)

10 A L1 x x x x x x

11 A L2 o x x x x x

12 A L3 o o x x x x

13 VAsys x x x x x x sys=system

14 VA sys dmd x x x x x x sys=system (1)

15 VA L1 x x x x x x

16 VAL2 o x x x x x

17 VA L3 o o x x x x

18 var sys x x x x x x sys=system

19 var L1 x x x x xx

20 var L2 o x x x x x

21 var L3 o o x x xx

22 W sys x x x x x x sys=system

23 Wsys dmd x x x x x x sys=system (1)

24 WL1 x x xxx x

25 W L2 o x x x x x

26 WL3 ooxxx x

27 PF sys x x x x x x

28 PF L1 x x x x x x

29 PF L2 oxxxx x

30 PF L3 o o x x x x

31 Hz x x x x x x

32 Phase seq. oo x x x x

33 Hours xxxxx x

34 kWh (+) x x x x x x Total or by user

35 kvarh (+) x x x x x x Total or by user

36 kWh (+) x x x x x x Partial or by tariff

37 kvarh (+) x x x x x x Partial or by tariff

38 kWh (-) x xxxxx Total

39 kvarh (-) x x x x x x Total

40 m3Gas x x x x x x Total

41 m3Cold H2O x x x x x x Total

42 m3Hot H2O x x x x x x Total

43 kWh H2Ox x x x x x Total

44 kWh out x x x x x x Total

45 AL1 THD x x x x x x

46 A L2 THD o x x x x x

47 A L3 THD o o x x x x

48 VL1 THD xxxxxx

49 V L2 THD o x x x x x

50 V L3 THD o o x x x x

51 V L1-2 THD x x x x x x

52 V L2-3 THD o x x x x x

53 V L3-1 THD o o x x x x

(x) = available; (o) = not available (zero indication on the display); (1) Max. value with data storage.

List of the variables that can be connected to:

Specifications are subject to change without notice EM2696 DS ENG 261012 9

EM26 96

Display pages

Sel.

pos. No 1st variable

(1st line)

2nd variable

(2nd line)

3rd variable

(3rd line) Note Applications

A B C D E F G H

1 Total kWh (+) Wsys dmd W sys dmd max x x x x x x x

2kWh (+) Admd max “PArt” “PArt” = Partial kWh (+) x x x

3 Total kvarh (+) VA sys dmd VA sys dmd max x x x x x

4 kvarh (+) VA sys “PArt” “PArt” = Partial kvarh (+) x x x

5 Totalizer 1 (2) Wsys (text) (3) (1) x x x x

6 Totalizer 2 (2) Wsys (text) (3) (1) x x x x

7 Totalizer 3 (2) Wsys (text) (3) (1) x x x x

8 kWh (+) t1 (text) (4) Wsys dmd (1) digital input enabled x x x x

9 kWh (+) t2 (text) (4) Wsys dmd (1) digital input enabled x x x x

10 kWh (+) t3 (text) (4) Wsys dmd (1) digital input enabled x x x x

11 kWh (+) t4 (text) (4) Wsys dmd (1) digital input enebled x x x x

12 kvarh (+) t1 (text) (4) Wsys dmd (1) digital input enabled x x x x

13 kvarh (+) t2 (text) (4) Wsys dmd (1) digital input enabled x x x x

14 kvarh (+) t3 (text) (4) Wsys dmd (1) digital input enabled x x x x

15 kvarh (+) t4 (text) (4) Wsys dmd (1) digital input enabled x x x x

16 kWh (+) X W X User X (1) specific function enabled x

17 kWh (+) Y W Y User Y (1) specific function enabled x

18 kWh (+) Z W Z User Z (1) specific function enabled x

19 Total kvarh (-) VA sys dmd VA sys dmd max x x

20 Total kWh (-) Wsys dmd Wsys dmd max x x x

21 Hours Wsys PF sys x x x x

22 Hours var sys PF sys x x x x

23 WL1 WL2 WL3 x x x

24 VAL1 VAL2 VAL3 x x

25 var L1 var L2 var L3 x x

26 PF L1 PF L2 PF L3 x x

27 VL1 VL2 VL3 x x x x x

28 VL1-2 VL2-3 VL3-1 x x

29 AL1 AL2 AL3 x x x

30 Phase seq. VLN sys Hz x x x x x x x

31 Phase seq. VLL sys Hz x x x

32 ASY VLL sys % x x x

33 ASY VLN sys % x x x

34 THD A1 THD A2 THD A3 x x

35 THD V1 THD V2 THD V3 x x

36 THD V12 THD V23 THD V 31 x x

37 Lot number Year DMD time x x x x x x x x

38 CT ratio Value of CT System x x x x x x x x

39 VT/PT ratio Value of VT Connection x x x x x x x x

40 a Alarm 1 status Set-point value Variable type x x x x

41 a Alarm 2 status Set-point value Variable type x x x x

42 a Alarm 3 status Set-point value Variable type x x x x

40 bPulse 1 status Output pulse x x x x x x x x

41 b Pulse 2 status Output pulse x x x x x x x x

42 b Pulse 3 status Output pulse x x x x x x x x

43 Serial port Address RS485 status x x x x x x x x

0Selector position which can be linked to any of the variable combinations listed above (No. from 1 to 36)

1Selector position which can be linked to any of the variable combinations listed above (No. from 1 to 36)

2Selector position which can be linked to any of the variable combinations listed above (No. from 1 to 36)

3Selector position which can be linked to any of the variable combinations listed above (No. from 1 to 36).

In this position the front LED blinks proportionally to the reactive energy (kvarh) being measured

(1) The page is available according to the enabled measurement. (2) m3Gas, m3Water,kWh remote heating, external kWh

counter.(3) Hot or Cold (water), gas, ENE (external energy meter). (4) The active tariffis displayed with an “A” before the “t1-

t2-t3-t4” simbols.

10 Specifications aresubject to change without notice EM2696 DS ENG 261012

EM26 96

Additional available information on the display

List of selectable applications

Type 1st line 2nd line 3rd line

Meter information pag. 1 Firmware release Year Year of production

Meter information pag. 2 Pulse LED Value

Meter information pag. 3 System 2w, 3w or 4w

Meter information pag. 4 CTratio Value of CT ratio

Meter information pag. 5 PT ratio Value of PT ratio

In case of alarm output

pag.6a

Alarm output 1, 2 or 3 status

(ON/OFF) Set-point value Variable type

In case of pulse output

pag. 6b

Pulse output 1,2 or 3 variable

link (kWh/kvarh)

Output pulse weight

(kWh/kvarh per pulse)

In case of communication

port pag.7 Serial port Address RS485 status (RX-TX)

In case of communication

port pag.8

Secondary address

(for M-bus protocol) Sn

Description Notes

ABasic domestic ** Main energy metering

BShopping centres ** Main energy metering

CAdvanced domestic** Main energy metering (total and based on tariff), gas and

water metering

DMulti domestic (also camping and marinas) */** Main energy metering (3 by single phase)

ESolar *Energy meter with some basic power analyzer functions

FIndustrial *Main energy metering

GAdvanced industrial ** Energy metering and power analysis

HAdvanced industrial for power generation *Complete energy metering and power analysis

Insulation between inputs and outputs

Measuring Inputs Relay

output Open collector

outputs Comm. port Digital inputs Auxiliary power supply

Measuring Inputs - 4kV 4kV 4kV 4kV 4kV

Relay output 4kV - - 4kV - 4kV

Open collector

outputs 4kV - - 4kV - 4kV

Comm. port 4kV 4kV 4kV - 4kV 4kV

Digital inputs 4kV - - 4kV - 4kV

Aux. power supply 4kV 4kV 4kV 4kV 4kV -

NOTE: all the models with auxiliary power supply have, mandatory, to be connected to external current transformers

because the insulation among the current inputs is just functional (100VAC).

Tamper proof and display page selection

Lock of programming with seal.

Selection of up to 4 main pages

(programmable by the user).

Easy access to specific display pages.

Notes:*Not available with option PF A. ** Not available with option PF B

Specifications are subject to change without notice EM2696 DS ENG 261012 11

EM26 96

3-CT and 2-VT/PT connections

3-ph, 3-wire, unbalanced load Fig. 4

2-CT and 2-VT/PT connections ARON

3-ph, 3-wire, unbalanced load Fig. 6

2-CT connections (ARON)

3-ph, 3-wire, unbalanced load Fig. 5

1-CT and 2-VT/PT connections

3-ph, 3-wire, balanced load Fig. 8

3-CT connection

3-ph, 3-wire, unbalanced load Fig. 3

1-CT connection

3-ph, 3-wire, balanced load Fig. 7

System type selection: 3P.n

System type selection: 3P.1

Wiring diagrams

3-CT and 3-VT/PT connections3-CT connection

3-ph, 4-wire, unbalanced load Fig. 2

3-ph, 4-wire, unbalanced load Fig. 1

System type selection: 3P.n

NOTE: a2-wire connection for voltage mea-

surement is available across 15 and 17 .

12 Specifications aresubject to change without notice EM2696 DS ENG 261012

EM26 96

2-CT connection

2-ph, 3-wire Fig. 9

Wiring diagrams

System type selection: 2P

2-CT and 2-VT/PT connections

2-ph, 3-wire Fig. 10

1-CT connection

1-ph, 2-wire Fig. 11

System type selection: 1P

1-CT and 1-VT connections

1-ph, 2-wireFig. 12

System type selection: 1P

100 to 230VAC/DC (“H” option) Fig.13

F= 250V [T] 100mA

Auxiliary power supply wiring diagrams

Digital inputs and RS485 portwiring diagrams

Digital Inputs RS485 port

RS485 NOTE: additional devices provided with RS485 areconnected in parallel. The termination of the serial output is car-

ried out only on the last instrument of the network, by means of a jumper between (A-) and (T).

Specifications are subject to change without notice EM2696 DS ENG 261012 13

EM26 96

1. Display

LCD-type with alphanumeric indications to:

-display configuration parameters;

-display all the measured variables.

2. Selector

To select the desired display pages and to lock the

programming.

3. Joystick

Toprogram the configuration parameters and scroll the

variables on the display.

4. LED

Red LED blinking proportionally to the energy being

measured.

Front panel description

Dimensions and Panel Cut-out

Open collector and relay outputs wiring diagrams

GND reference VDC reference

The load resistances (RC) must be designed so that the close contact current is lower than

100mA; the VDC voltage must be lower than or equal to 30VDC.

Open Collector Open Collector Relay

VDC

Out 1

Out 2

Out 3

GND

VDC

123

Out 1

VDC

GND

Out 2

VDC

GND

Out 3

VDC

GND

123

91mm