-3
+4
DO NOT
SCALE FROM
THIS PRINT
No OF POSITIONS PER ROW
-02 THRU -50
BODY SPEC
-D: DOUBLE ROW
(USE CLP-XX-D)
LEAD STYLE SPEC
-02: SURFACE MOUNT
(USE C-106-X2-XXX)
(SEE NOTE 9)
OPTION
-P: PICK & PLACE PAD (USE MPP-01)
(AVAILABLE ON POSITON -05 THRU -50 ONLY)
(NOT AVAILABLE WITH -PA OR -K OPTIONS)
(SEE FIG. 3, SHT 2)
-A: ALIGNMENT PIN (USE CLP-XX-D-XX)
(NOT AVAILABLE WITH -PA OPTION)
(SEE FIG. 3, SHT 2)
-TR: TAPE AND REEL
-BE: BOTTOM ENTRY ONLY (USE CLP-XX-DBE-XX)
-PA: PICK & PLACE PAD WITH ALIGNMENT PINS
(NOT AVAILABLE WITH -P, -A, OR -K OPTIONS)
(SEE SHT 2, TABLE 3)
-K: POLYIMIDE FILM PAD (POSITIONS -05 THRU -50 ONLY)
(USE K-500-300, SEE FIG. 5, SHT 2)
(.005[0.13] THICKNESS WITH SILICONE ADHESIVE)
(NOT AVAILABLE WITH -P OR -PA OPTIONS)
CLP-1XX-XX-XXX-D-XX
PLATING SPEC
(VALUES GIVEN ARE IN MICRO-INCHES)
-F: FLASH SELECTIVE, 3 Au / 50 Ni MIN ON
CONTACT, MATTE TIN TAIL
-L: LIGHT SELECTIVE, 10 Au / 50 Ni MIN ON
CONTACT, MATTE TIN TAIL
-S: SELECTIVE, 30 Au / 50 Ni MIN ON
CONTACT, MATTE TIN TAIL
-G: GOLD, 10 Au / 50 Ni MIN ON
CONTACT, 3 Au / 50 Ni MIN ON TAIL
-H: HEAVY GOLD, 30 Au / 50 Ni MIN ON
CONTACT, 3 Au / 50 Ni MIN ON TAIL
-LM: LIGHT SELECTIVE, 10 Au / 50 Ni MIN ON
CONTACT, MATTE TIN TAIL
-FM: FLASH SELECTIVE, 3 Au / 50 Ni MIN ON
CONTACT, MATTE TIN TAIL
-SM: SELECTIVE, 30 Au / 50 Ni MIN ON
CONTACT, MATTE TIN TAIL
-LTL: LIGHT SELECTIVE, 10 Au / 50 Ni MIN ON
CONTACT, TIN/LEAD (90/10+/-5%) TAIL
(No OF POS X .0500[1.270]) + .017[0.43]
±.008[0.20]
(SEE NOTE 3 AND 7)
.120 3.05
REF
.034 0.85
REF
No OF POS x .0500[1.270]) - .0500[1.270]
(TOLERANCE ACCUM ±.0020[0.051])
.050
REF
1.27
-D
-D-BE
CLP-XX-DBE-XX
.016
x .005[0.13] REF
0.41
.084
REF
2.12
"A"
"A"
"B"
"B"
-D-BE
-D
CLP-XX-D-XX
C-106-22-XXX
2.5
MAX SWAY
(TYP)
-D
-D-BE
.170
±.010
4.31
±0.25
.090
-
.001
+
.003 2.29
-
0.03
+
0.08
(MEASURE AT BEND)
SECTION "A"-"A"
.004[[0.10]
POS. 02-35
.006[0.15]
POS. 36-50
SECTION "B"-"B"
C
01
02
FIG. 1
(-D BODY: CLP-XX-D-XX)
(-D-BE BODY: CLP-XX-DBE-XX)
(DIFFERENT AS SHOWN,
OTHERWISE SAME AS -D BODY)
C
C
C
CD
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01 [.3] 2
.XXX:
.005 [.13]
.XXXX:
.0020 [.051]
MATERIAL:
LOW PROFILE .050 x .050 DOUBLE ROW ASM
BY:
CLP-1XX-XX-XXX-D-XX
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
PURVIS
01/31/1994
3
1
SHEET SCALE: 3:1
F:\DWG\MISC\MKTG\CLP-1XX-XX-XXX-D-XX-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
1.
C
REPRESENTS A CRITICAL DIMENSION
2. MINIMUM PUSHOUT FORCE: .5LB (8 OZ)
3. ONE POSITON WILL BE LOST FOR EVERY CUT MADE ON A
SOCKET STRIP
4. TUBE PACKAGE POSITIONS 5-50 ONLY. POSITIONS 2-4 ARE
TO BE LAYERED PACKAGED.
5. SHEAR TAILS TO DIMENSIONS SHOWN
6. PARTS TO BE SYMMETRICAL ABOUT
C
L
WITHIN ±.0015[0.038].
7. ENDWALL AFTER CUTTING: .0185[0.470]±.0025[0.064]
8. VOID CORES MAY NOT BE PRESENT.
9. HAND FILL USE C-106-01-XX.
AUTOMATION USE C-106-22-XX.
C-106-02-XX CAN BE
SUBBED FOR C-106-22-XX.
10. MAX CUT FLASH: .010[0.27] WITH NO FLASH ALLOWED IN
HOLES OR EXTENDING BELOW LEADS.
11. MAX BURR: .005[.13].
INSULATOR: LCP, UL 94 VO, COLOR: BLACK
CONTACT: PHOS BRONZE
REVISION CD
.019 0.47
(No OF POS x .0500[1.270]) - .100[2.54]
22.86
.005
REF (TYP 4 SIDES)
45°
X
.0050
REF (TYP)
0.127
.0100
REF (TYP)
0.254
.025
REF (TYP)
0.6350
.0070 0.178
REF (TYP)
"N"
(SEE NOTE)
"Q"
3.45
(SEE NOTE)
.250
REF
6.35
MPP-01
.100 2.54
"P"
"A"
"M"
.325 8.26
REF
"T"
PPP-38-X-X-XX
.121 3.07
.051 1.30
.035
REF
0.89
.275 6.99
"R"
(SEE NOTE)
"S"
(SEE NOTE)
.019
±.010
0.48
±0.25
.1575
±.0050
4.000
±0.127
.095 2.41
AVAILABLE ON POSITIONS 05 THRU 50 ONLY
NOTE: "N" = USED MEASURED DIMENSION (REF)
"Q" = [("N" - .250[6.35])/2] ±.020[0.51]
FIG. 3
-P: PICK AND PLACE PAD
(AVAILABLE ON POSITION 05 THRU 50 ONLY)
(NOT AVAILABLE WITH -PA OR -K OPTIONS)
FIG. 4
-PA: PICK & PLACE PAD WITH ALIGNMENT PINS
(NOT AVAILABLE WITH -P, -A OR -K OPTIONS)
FIG. 5
-K: POLYIMIDE FILM PAD
(AVAILABLE ON POSITION 05 THRU 50 ONLY)
(NOT AVAILABLE WITH -P OR -PA OPTIONS)
FIG. 2
-A: ALIGNMENT PIN
(3 POSITION MINIMUM)
(NOT AVAILABLE WITH -PA OPTION)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG. 1)
NOTE: "R" = USED MEASURED DIMENSION (REF)
"S" = {("R" - .1575[4.000])/2} ±.020[0.51]
C
CC
C
C
C
C
C
SHEET OF
LOW PROFILE .050 x .050 DOUBLE ROW ASM
BY:
CLP-1XX-XX-XXX-D-XX
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
PURVIS
01/31/1994
3
2
SHEET SCALE: 4:1
REVISION CD
F:\DWG\MISC\MKTG\CLP-1XX-XX-XXX-D-XX-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
PACKAGING
(SEE NOTE 4, SHEET 1)
PT-CLP001-PA
PT-CLX-002-D
PT-CLX-001-D
* = IF APPLICABLE
SHEET OF
LOW PROFILE .050 x .050 DOUBLE ROW ASM
BY:
CLP-1XX-XX-XXX-D-XX
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
PURVIS
01/31/1994
3
3
SHEET SCALE: 4:1
REVISION CD
F:\DWG\MISC\MKTG\CLP-1XX-XX-XXX-D-XX-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322