PIC18F1320-I/PREL - Microchip Technology, Inc.

PIC18F1220/1320

Data Sheet

18/20/28-Pin High-Performance,

Enhanced Flash Microcontrollers

with 10-bit A/D and nanoWatt Technology

Information contained in this publication regarding device

applications a nd the like is p ro vid ed only f or yo ur c o n ve nience

and may be supers eded by updates. It is y our res po nsibilit y to

ensure that your application meets with your specifications.

MICROCHIP MAKES NO REPRESENTATIONS OR

WARRANTIES OF ANY KIND WHETHER EXPRESS OR

IMPLIED, WRITTEN OR ORAL, STATUTORY OR

OTHERWISE, RELATED TO THE INFORMATION,

INCLUDING BUT NOT LIMITED TO ITS CONDITION,

QUALITY, PERFORMANCE, MERCHANTABILITY OR

FITNESS FOR PURPOSE. Microchip disclaims all liability

arising from this information and its use. Use of Microchip

devices in life support and/or safety applications is entirely at

the buyer’s risk, and the buyer agrees to defend, indemnify and

hold harmless Microchip from any and all damages, claims,

suits, or expenses resulting from such use. No licenses are

conveyed, implicitly or otherwise, under any Microchip

intellectual property rights.

Trademarks

The Microchip name and logo, the Microchip logo, Accur on,

dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro, PICST ART,

PRO MATE, PowerSmart, rfPIC and SmartShunt are

registered trademarks of Microchip Technology Incorporated

in the U.S.A. and other countries.

AmpLab, FilterLab, Migratable Memory, MX DEV, MXLAB,

SEEV AL, SmartSensor and The Embedded Control Solutions

Company are registered trademarks of Microchip Technology

Incorporated in the U.S.A.

Analog-for-the-Digital Age, Application Maestro, CodeGuard,

dsPICDEM, dsPICDEM.net, dsPICworks, ECAN,

ECONOMONITOR, FanSense, FlexROM, fuzzyLAB,

In-Circuit Serial Programming, ICSP, ICEPIC, Linear Active

Thermistor, Mindi, MiWi, MPASM, MPLIB, MPLINK, PIC kit,

PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal,

PowerInf o, PowerMate, PowerTool, REAL ICE, rfLAB,

rfPICDEM, Select Mode, Smart Serial, SmartTel, Total

Endurance, UNI/O, WiperLock and ZENA are trademarks of

Microchip Technology Incorporated in the U.S.A. and other

countries.

SQTP is a service mark of Microchip Technology Incorporated

in the U.S.A.

All other trademarks mentioned herein are property of their

respective companies.

Printed on recycled paper.

Note the following details of the code protection feature on Microchip devices:

• Microchip products meet the specification contained in their particular Microchip Data Sheet.

• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the

intended manner and under normal conditions.

• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our

knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data

Sheets. Most likely, the person doing so is engaged in theft of intellectual property.

• Microchip is willing to work with the customer who is concerned about the integrit y of their code.

• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not

mean that we are guaranteeing the product as “unbreakable.”

Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our

products. Attempts to break Microchip’s code protection feature may be a violat ion of the Digital Millennium Copyright Act. If suc h a c t s

allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.

Microchip received ISO/TS-16949:2002 certification for its worldwide

headquarters, design and wafer fabrication facilities in Chandler and

T empe, Arizona, Gresham, Oregon and Mountain View , California. The

Company’s quality system processes and procedures are for its

PICmicro® 8-bit MCUs, KEELOQ® code hopping devices, Serial

EEPROMs, microperipherals, nonvolatile memory and analog

products. In addition, Microchip’s quality system for the design and

manufacture of development systems is ISO 9001:2000 certified.

Low-Power Features:

• Power Managed modes:

- Run: CPU on, pe ripherals on

- Idle: CPU off, peripherals on

- Sleep: CPU off, peripherals off

• Pow er Consumption modes :

- PRI_RUN: 150 μA, 1 MHz, 2V

- PRI_IDLE: 37 μA, 1 MHz, 2V

- SEC_RUN: 14 μA, 32 kHz, 2V

- SEC_IDLE: 5.8 μA, 32 kHz, 2V

- RC_RUN: 110 μA, 1 MHz, 2V

- RC_IDLE: 52 μA, 1 MHz, 2V

- Sleep: 0.1 μA, 1 MHz, 2V

• Timer1 Oscillator: 1.1 μA, 32 kHz, 2V

• Watchdog Timer: 2.1 μA

• Two-Speed Os ci ll ator Start-up

Oscillators:

• Four Crystal modes:

- LP, XT, HS: up to 25 MHz

- HSPLL: 4-10 MHz (16-40 MHz internal)

• Two External RC modes, up to 4 MHz

• Two External Clock modes, up to 40 MHz

• Internal oscillator block:

- 8 user-selectable frequencies: 31 kHz, 125 kHz,

250 kHz, 500 kHz, 1 MHz, 2 MHz, 4 MHz, 8 MH z

- 125 kHz to 8 MHz calibrated to 1%

- Two modes select one or two I/O pins

- OSCTUNE – Allows user to shift frequency

• Secondary oscillator using Timer1 @ 32 kHz

• Fail-Safe Clock Monitor

- Allows for safe shutdown if peripheral clock stops

Peripheral Highl ight s:

• High current sink/source 25 mA/25 mA

• Three extern al inte rrup t s

• Enhanced Capture/Compare/PWM (ECCP) module:

- One, two or four PWM outputs

- Selectab le pol ari ty

- Programmable dead time

- Auto-Shutdown and Auto-Restart

- Capture is 16-bit, max resolution 6.25 ns (TCY/16)

- Compare is 16-bit, max resolution 100 ns (TCY)

• Compa t ib le 10-b it, up to 13-chan nel Analog -to-

Digital Converter module (A/D) with programmable

acquisition time

• Enhanced USART module:

- Supports RS-485, RS-232 and LIN 1.2

- Auto-Wake-up on Start bit

- Auto-Baud Detect

Special Microcontroller Features:

• 100,000 eras e/w ri te cy cl e Enhan ced Flash

program memory typical

• 1,000,000 erase/write cycle Data EEPROM

memory typical

• Flash/Data EEPROM Retention: > 40 years

• Self-programmable under software control

• Priority levels for interrupts

• 8 x 8 Single-Cycle Hardware Multiplier

• Extended Watchdog Timer (WDT):

- Programmable period from 41 ms to 131s

- 2% stability over VDD and Temperature

• Single-supply 5V In-Circuit Serial Programming™

(ICSP™) via two pins

• In-Circuit Debug (ICD) via two pins

• Wide operating voltage range: 2.0V to 5.5V

Device

Program Memory Data Memory

I/O 10-bit

A/D (ch) ECCP

(PWM) EUSART Timers

8/16-bit

Flash

(bytes) # Sing le-Word

Instructions SRAM

(bytes) EEPROM

(bytes)

PIC18F1220 4K 2048 256 256 16 7 1 Y 1/3

PIC18F1320 8K 4096 256 256 16 7 1 Y 1/3

18/20/28-Pin High-Performance, Enhanced Flash MCUs

with 10-bit A/D and nanoWatt Technology

PIC18F1220/1320

Pin Diagrams

RB3/CCP1/P1A

RB2/P1B/INT2

OSC1/CLKI/RA7

OSC2/CLKO/RA6

VDD/AVDD

RB7/PGD/T1OSI/

RB6/PGC/T1OSO/

RB5/PGM/KBI1

RB4/AN6/RX/

RA0/AN0

RA1/AN1/LVDIN

RA4/T0CKI

MCLR/VPP/RA5

VSS/AVSS

RA2/AN2/VREF-

RA3/AN3/VREF+

RB0/AN4/INT0

RB1/AN5/TX/

PIC18F1X20

18-Pin PDIP, SOIC

RB3/CCP1/P1A

RB2/P1B/INT2

OSC1/CLKI/RA7

OSC2/CLKO/RA6

VDD

RB7/PGD/T1OSI/

RB6/PGC/T1OSO/

RB5/PGM/KBI1

RB4/AN6/RX/

RA0/AN0

RA1/AN1/LVDIN

RA4/T0CKI

MCLR/VPP/RA5

VSS

RA2/AN2/VREF-

RA3/AN3/VREF+

RB0/AN4/INT0

RB1/AN5/TX/

PIC18F1X20

AVDDAVSS 615

20-Pin SSOP

28-Pin QFN

RA0/AN0

RA4/T0CKI

MCLR/VPP/RA5

AVSS

RA2/AN2/VREF-

RA3/AN3/VREF+

RA1/AN1/LVDIN

OSC1/CLKI/RA7

OSC2/CLKO/RA6

VDD

AVDD

RB7/PGD/T1OSI/P1D/KBI3

RB6/PGC/T1OSO/T13CKI/P1C/KBI2

RB5/PGM/KBI1

PIC18F1X20

VSS

RB2/P1B/INT2

RB0/AN4/INT0

RB1/AN5/TX/CK/INT1

RB4/AN6/RX/DT/KBI0 RB3/CCP1/P1A

T13CKI/P1C/KBI2

P1D/KBI3

CK/INT1 DT/KBI0

P1D/KBI3

T13CKI/P1C/KBI2

CK/INT1 DT/KBI0

© 2006 Microchip Technology Inc. DS39605D-page 3
PIC18F1220/1320
Table of Contents
1.0 Device Overview .......................................................................................................................................................................... 5
2.0 Oscillator Configurations............................................................................................................................................................ 11
3.0 Power Managed Modes ............................. ..... .. .. .... .. .. .. .. ..... .... .. .. .. .. .. .. ....... .. .. .. .. .... .. ..... .. .. .. ...................................................... 19
4.0 Reset.......................................................................................................................................................................................... 33
5.0 Memory O rganization................................................................................................................................................................. 41
6.0 Flash Pro g ram Memory............................ ............................ ........................... ........................................................................... 57
7.0 Data EEPR OM Mem o ry.... ............... ........................... ............................ ........................... ........................................................ 67
8.0 8 x 8 Hardware Multiplier............................................................................................................................................................ 71
9.0 Interrupts.................................................................................................................................................................................... 73
10.0 I/O Ports.............. ................................. ........................... ............................ ............................................................................... 87
11.0 Tim er0 Module ........................................................................................................................................................................... 99
12.0 Tim er1 Module ......................................................................................................................................................................... 103
13.0 Tim er2 Module ......................................................................................................................................................................... 109
14.0 Tim er3 Module ......................................................................................................................................................................... 111
15.0 Enhanc ed Capture/Com pare/PW M (ECCP) Module................................................................................................................ 115
16.0 Enhanced Addressable Universal Synchronous Asynchronous Receiver T ransm itter (EUS ART). . ........................................ 131
17.0 10-Bit Analog-to-Digital Converter (A/D) Module ................................. ........... .... .... ........... ...... .... ............................................ 155
18.0 Low-V oltage Detect.................................................................................................................................................................. 165
19.0 Specia l Features of the CPU.................... ............................ ..................... ............................................................................... 171
20.0 Instruction Set Summary.......................................................................................................................................................... 191
21.0 Development Support............................................................................................................................................................... 233
22.0 Electrical Characteristics.......................................................................................................................................................... 239
23.0 DC and AC Characteristics Graphs and Tables................................... ......... .... .... .. ......... .... .... .... .. .......................................... 269
24.0 Packagin g  In fo rmation.............................. ..................... ............................ ............................................................................... 287
Appendix A: Revision History . ............................................................................................................................................................ 293
Appendix B: Device Differences ........................................................................................................................................................ 293
Appendix C: Conversion Considerations .......................... .... .. ....... .... .. .... .. .... ....... .. .... .. .... .. ....... .... .. .................................................. 294
Appendix D: Migration from Baseline to Enhanced Devices.............................................................................................................. 294
Appendix E: Migration from Mid-Range to Enhanced Devices............................... .... .... .... ........... .... .... ......... ................................... 295
Appendix F: Migration from High-End to Enhanced Devices.............................. .... .... .. .... .. ....... .... .... .. .... .......................................... 295
Index .................................................................................................................................................................................................. 297
On-Line Support................ .... .... .. .... ....... .... .... .. .... ......... .. .... .... .. ......... .. .... .... .. ......... .... .. .... ................................................................. 305
Systems Information and Upgrade Hot Line...................................................................................................................................... 305
Reader Response.............................................................................................................................................................................. 306
PIC18F1220/1320 Product Identification System .............................. .... .... .... ......... .... .. .... ......... .... .... ................................................ 307

PIC18F1220/1320

TO OUR VALUED CUSTOMERS

It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip

products. To this end, we will continue to improve our pu blications to better s uit your needs. Our publications will be refined and

enhanced as new volumes and updates are introduced.

If you have any questions o r c omm ents regarding this publication, please c ontact the M arketing Communications Department via

E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We

welcome your feedback.

Most Current Data Sheet

To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:

http://www.microchip.com

You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of an y page.

The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).

Errata

An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current

devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision

of silicon and revision of document to which it applies.

To determine if an errata sheet exists for a particular device, please check with one of the following:

• Microchip’s Worldwide Web site; http://www.microchip.com

• Your local Microc hip sales office (see last page)

When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are

using.

Customer Noti fic atio n Syst em

PIC18F1220/1320

1.0 DEVICE OVERVIEW

This do cu me n t conta i ns dev ic e spec if i c in f orm at i on fo r

the following devices:

This family offers the advantages of all P IC18 m i crocon-

troll ers – namel y, high compu tationa l perfor manc e at an

economical price – with the addition of high endurance

Enhanced Flash program memory. On top of these fea-

tures, the PIC18F1220/1320 family introduces design

enhancements that make these microcontrollers a logical

choice for many high-performance, power sensitive

applications.

1.1 New Core Features

1.1.1 nanoWatt TECHNOLOGY

All of the devices in the PIC18F1220/1320 family incor-

porate a range of features that can significantly reduce

power consump tion during operation. Key items include:

•Alternate Run Modes: By clocking the controller

from the Timer1 source or the internal oscillator

block, power consumption during code execution

can be reduced by as much as 90%.

•Multiple Idle Modes: The controller can also run

with its CPU core disabled, but the peripherals are

still active. In these states, power consumption can

be reduced even further, to as little as 4% of normal

operation requirements.

•On-the-fly Mode Switching: The power managed

modes are invoked by user code during operation,

allowing the user to incorporate power-saving ideas

into their appl ic atio n’s softw are desig n.

•Lower Consumption in Key Modules: The power

requirements for both Timer1 and the Watchdog

Timer have been reduced by up to 80%, with typical

values of 1.1 and 2.1 μA, respectively.

1.1.2 MULTIPLE OSCILLATOR OPTIONS

AND FEATURES

All of the devices in the PIC18F1220/1320 family offer

nine different oscillator options, allowing users a wide

range of choices in developing application hardware.

These include:

• Four Crystal modes, using crystals or ceramic

resonators.

• Two External Clock modes, offering the option of

using two pins (oscillator input and a divide-by-4

clock output), or one pin (oscillator input, with the

second pin reassigned as general I/O).

• Two External RC Oscillator modes, with the same

pin options as the External Clock modes.

• An internal oscillator block, which provides an

8 M Hz clock (±2% accuracy) and an INTRC source

(approximately 31 kHz, stable over temperature and

VDD), as well as a range of 6 user-selectable clock

frequencies (from 125 kHz to 4 MHz) for a total of

8 c lock frequencies.

Besides its availability as a clock source, the internal

oscill ato r blo ck pro vid es a s t ab le re ference sourc e th at

gives the family additional features for robust

operation:

•Fail-Safe Clock Monitor: This option constantly

monitors the main clock source against a reference

signal provided by the internal oscillator. If a clock fail-

ure occurs, the controller is switched to the internal

oscillator block, allowing for continued low-speed

operation, or a safe application shut down.

•Two-Speed S tart-up: This option allows the internal

oscillator to serve as the clock source from Power-

on Reset, or wake-up from Sleep mode, until the

primary clock source is available. This allows for

code execution during what would otherwise be the

clock start-up interval and can even allow an appli-

cation to perform routine background activities and

return to Sleep without returning to full power

operation.

1.2 Other Special Features

•Memory Endurance: The Enhanced Flash cells for

both program memory and data EEPROM are rated

to last for many thousands of erase/write cycles –

up to 100,000 for program memory and 1,000,000

for EEPROM. Data retention without refresh is

conservatively estimated to be greater than

40 years.

•Self-programmability: These devices can write to

their own program memory spaces under internal

software control. By using a bootloader routine

located in the protected Boot Bloc k at the top of pro-

gram memory, it becomes possible to create an

application that can update itself in the field.

•Enhanced CCP module: In PWM mode, this

module provides 1, 2 or 4 modulated outputs for

controlling half-bridge and full-bridge drivers. Other

features include auto-shutdown, for disabling PWM

outputs on interrupt or other select conditions and

auto-restart, to reactiv ate outpu ts once the condi tio n

has cle are d.

•Enhanced USART: This serial communication

module features automatic wake-up on Start bit and

automat ic baud rate dete ction a nd supp orts RS-23 2,

RS-485 and LIN 1.2 protocols, making it ideally

suited for use in Local Interconnect Network (LIN)

bus applic ations.

•10-bit A/D Converter: This module incorporates

programmable acquisition time, allowing for a

channel to be selected and a conversion to be

initiated without waiting for a sampling period and

thus, reduce code overhead.

•Extended Watchdog Timer (WDT): This enhanced

version incorporates a 16-bit prescaler, allowing a

time-out range from 4 ms to over 2 minutes that is

stable across operating voltage and temperature.

• PIC18F1220 • PIC18F1320

PIC18F1220/1320

1.3 Details on Indivi dual Family

Members

Devices in the PIC18F1220/1320 family are available

in 18-pin , 20-pin and 28 -pin pack ages. A block dia gram

for this device family is shown in Figure 1-1.

The devices are differentiated from each other only in

the amount of on-chip Flash program memory

(4 Kbytes for the PIC18F1220 device, 8 Kbytes for the

PIC18F1320 device). These and other features are

summa riz ed in Table 1-1.

A block diagram of the PIC18F1220/1320 device

architecture is provided in Figure 1-1. The pinouts for

this device family are listed in Table 1-2.

TABLE 1-1: DEVICE FEATURES

Features PIC18F1220 PIC18F1320

Operating Frequency DC – 40 MHz DC – 40 MHz

Program Memo ry (Bytes ) 4096 8192

Program Memo ry (Instructions) 2048 4096

Data Me mo ry (Byte s) 256 256

Data EEPROM Memory (Bytes) 256 256

Interrupt Sources 15 15

I/O Ports Ports A, B Ports A, B

Timers 4 4

Enhanced Capture/Compare/PWM Modules 1 1

Serial Communications Enhanced USART Enhanced USART

10-bit Analog-to-Digital Module 7 input channels 7 input channels

Resets (and Delays)

POR, BOR,

RESET Instruction, Stack Full,

St ack U nde rflo w (PWRT, OST),

MCLR (optional), WDT

POR, BOR,

RESET Instruction, Stack Full ,

Stack Underf low (PW RT, OST),

MCLR (optional), WDT

Programmab le Low-Voltage Dete ct Yes Yes

Programmab le Brown-o ut Rese t Yes Yes

Instruction Set 75 Instructions 75 Instructions

Packages

18-pin SDIP

18-pin SOIC

20-pin SSOP

28-pin QFN

18-pin SDIP

18-pin SOIC

20-pin S SOP

28-pin QFN

PIC18F1220/1320

FIGURE 1-1: PIC18F1220/1320 BLOCK DIAGRAM

Instruction

Decode &

Control

PORTA

PORTB

RA4/T0CKI

MCLR/VPP/RA5(1)

Enhanced

Timer0 Timer1 Timer2

RA3/AN3/VREF+

RA2/AN2/VREF-

RA1/AN1/LVDIN

RA0/AN0

Data Latch

Data RAM

Address Latch

Address<12>

12(2)

BSR FSR0

FSR1

FSR2

412 4

PCH PCL

PCLATH

31 Level Stack

Program Counter

PRODLPRODH

8 x 8 Multiply

WREG

BIT OP 8

ALU<8>

Address Latch

(8 Kbytes)

Data Latch

inc/dec logic

21 8

Data Bus<8>

Instruction

ROM Latch

Timer3

Bank0, F

PCLATU

PCU

OSC2/CLKO/RA6(2)

USART

Table Latch

Table Pointer <2>

inc/dec

logic

RB0/AN4/INT0

RB4/AN6/RX/DT/KBI0

RB1/AN5/TX/CK/INT1

RB2/P1B/INT2

RB3/CCP1/P1A

RB5/PGM/KBI1

RB6/PGC/T1OSO/

RB7/PGD/T1OSI/

OSC2/CLKI/RA7(2)

Decode

Power-up

Timer

Power-on

Reset

Watchdog

Timer

VDD, VSS

Brown-out

Reset

Precision

Reference

Voltage

Low-Voltage

Programming

In-Circuit

Debugger

Oscillator

Start-up Timer

Timing

Generation

OSC1

(2)

OSC2

(2)

T1OSI

T1OSO

INTRC

Oscillator

Fail-Safe

Clock Monitor

Note 1: RA5 is availabl e only when the MCLR Reset is disabled.

2: OSC1, OSC2, CLKI and CLKO are only available in select oscillator modes and when these pins are not being used as digital

I/O. Refer to Section 2.0 “Oscillato r Config ura tions ” for additional information.

CCP

Enhanced

T13CKI/P1C/KBI2

Program Memory

(4 Kbytes)

PIC18F1220

PIC18F1320

A/D Converter

Data EEPROM

P1D/KBI3

MCLR

(1)

PIC18F1220/1320

TABLE 1-2: PIC18F1220/1320 PINOUT I/O DESCRIPTIONS

Pin Name

Pin Numbe r Pin

Type Buffer

Type Description

PDIP/

SOIC SSOP QFN

MCLR/VPP/RA5

MCLR

VPP

RA5

441I

—

Master Cl ear (input) or pr og ramming voltage (input ) .

Master Clear (Reset) input. This pin is an active-low

Reset to the dev ic e.

Programm ing voltage input.

Digital in put.

OSC1/CLKI/RA7

OSC1

CLKI

RA7

16 18 21 I

I/O

CMOS

Oscillator crystal or ex te rn al cl ock input.

Oscillat or crystal input o r ex te rnal cloc k source

input. ST bu ffer whe n configur ed in R C m ode,

CMOS ot h erwise.

External clock source input. Always associated with

pin function OSC1. (See related OSC1/CLKI,

OSC2/CLKO pins.)

General purpose I/O pin.

OSC2/CLKO/RA6

OSC2

CLKO

RA6

15 17 20 O

I/O

—

Oscillat or cr ystal or clock ou tp ut .

Oscillat or cr ystal output. C onnects to crys tal or

resonator in Crystal Oscillator mode.

In RC, EC and INTRC modes, OSC2 pin outputs

CLKO , wh ic h has 1/4 the fre quency of O SC 1 and

denote s in st ru ct i on cycle rat e.

General purpose I/O pin.

PORTA is a bidi r ec tion al I/O port.

RA0/AN0

RA0

AN0

1126

I/O

IST

Analog Digital I/O.

Analog inp ut 0.

RA1/AN1/LVDIN

RA1

AN1

LVDIN

2227

I/O

Analog

Digital I/O.

Analog input 1.

Low-Voltage Detect input.

RA2/AN2/VREF-

RA2

AN2

VREF-

677

I/O

Analog

Digital I/O.

Analog input 2.

A/D refer ence voltage (lo w) input.

RA3/AN3/VREF+

RA3

AN3

VREF+

788

I/O

Analog

Digit al I/O.

Analog input 3.

A/D reference voltage (high) input.

RA4/T0CKI

RA4

T0CKI

3328

I/O

IST/OD

ST Digital I/O. Open-drain when configured as output.

Time r0 ext ernal cloc k input.

RA5 See the MCLR/VPP/RA5 pin.

RA6 See the OSC2/CLKO/RA6 pin.

RA7 See th e O SC 1/CLKI/RA7 pin.

Legend: TTL = TTL compat ibl e i npu t CMOS = CMOS co m patible i nput or output

ST = Schmitt Trigger input with CMOS levels I = Input

O=Output P =Power

OD = Open-dr ai n ( no P di ode to VDD)

PIC18F1220/1320

PORTB is a bidirectional I/O port. PORTB can be software

programmed for internal weak pull-ups on all inputs.

RB0/AN4/INT0

RB0

AN4

INT0

899

I/O

TTL

Analog

Digital I/O.

Analog inp ut 4.

External interrupt 0.

RB1/AN5/TX/CK/INT1

RB1

AN5

INT1

91010

I/O

TTL

Analog

—

Digital I/O.

Analog inp ut 5.

EUSART asy nc hr onous trans m it.

EUSART synchronous clock (see related R X/ D T) .

External interrupt 1.

RB2/P1B/INT2

RB2

P1B

INT2

17 19 23 I/O

TTL

—

Digital I/O.

Enhanced CCP1 / PW M ou tp ut.

External interrupt 2.

RB3/CCP1/P1A

RB3

CCP1

P1A

18 20 24 I/O

I/O

TTL

—

Digital I/O.

Capture 1 in put/Compare 1 output/P WM 1 outpu t.

Enhanced CCP1 / PW M ou tp ut.

RB4/AN6/RX/DT/KBI0

RB4

AN6

KBI0

10 11 12 I/O

I/O

TTL

Analog

TTL

Digital I/O.

Analog inp ut 6.

EUSART asynchrono us rec ei ve .

EUSART syn chronous data (see related TX/CK).

Interru pt-on-change pin.

RB5/PGM/KBI1

RB5

PGM

KBI1

11 12 13 I/O

I/O

TTL

Digital I/O.

Low-Volt age ICSP Programming enable pin.

Interru pt-on-change pin.

RB6/PGC/T1OSO/

T13CKI/P1C/KBI2

RB6

PGC

T1OSO

T13CKI

P1C

KBI2

12 13 15

I/O

TTL

—

TTL

Digital I/O.

In-Circuit Debugger and ICSP prog ramming clock pin.

Timer1 osci l lator output.

Ti mer1/T imer3 external clock output.

Enhanced CCP1 / PW M ou tp ut.

Interru pt-on-change pin.

RB7/PGD/T1OSI/

P1D/KBI3

RB7

PGD

T1OSI

P1D

KBI3

13 14 16

I/O

TTL

CMOS

—

TTL

Digital I/O.

In-Ci rcuit Debugger and I CS P programming data pin.

T imer1 oscillator input.

Enhanced CCP1 / PW M ou tp ut.

Interru pt-on-change pin.

VSS 5 5, 6 3, 5 P — Ground reference for logic and I/O pins.

VDD 14 15, 16 1 7, 19 P — Positive supply for logic and I/O pins.

NC — — 18 — — No connect.

TABLE 1-2: PIC18F1220/1320 PINOUT I/O DESCRIPTIONS (CONTINUED)

Pin Name

Pin Numbe r Pin

Type Buffer

Type Description

PDIP/

SOIC SSOP QFN

Legend: TTL = TTL compat ibl e i npu t CMOS = CMOS co m patible i nput or output

ST = Schmitt Trigger input with CMOS levels I = Input

O=Output P =Power

OD = Open-dr ai n ( no P di ode to VDD)

PIC18F1220/1320

NOTES:

PIC18F1220/1320

2.0 OSCILLATOR

CONFIGURATIONS

2.1 Oscillator Types

The PIC18F1220 and PIC18F1320 devices can be

operated in ten dif ferent osci llator modes. The user can

program the configuration bits, FOSC3:FOSC0, in

Configuration Register 1H to select one of these ten

modes:

1. LP Low-Power Crystal

2. XT Crystal/Resonator

3. HS High-Speed Crystal/Resonator

4. HSPLL High-Speed Crystal/Resonator

with PLL enabled

5. RC External Resistor/Capacitor with

FOSC/4 output on RA6

6. RCIO Extern al Resi st or/C apacito r with

I/O on RA 6

7. INTIO1 Intern al Osci ll ator with F OSC/4

output on RA6 and I/O on RA7

8. INTIO2 Internal O scil lat or with I/O on RA6

and RA7

9. EC Extern al Cloc k with FOSC/4 output

10. ECIO External Clock with I/O on RA6

2.2 Crystal Oscill a tor/Ceramic

Resonators

In XT, LP, HS or HSPLL Oscillator modes, a crystal or

ceramic resonator is connected to the OSC1 and

OSC2 pins to establish oscillation. Figure 2-1 shows

the pin connections.

The oscillator design requires the use of a parallel cut

crystal.

FIGURE 2-1: CRYSTAL/CERAMIC

RESONATOR OPERATION

(XT, LP, HS OR HSPLL

CONFIGURATION)

T ABLE 2-1: CAPACITOR SELECTION FOR

CERAMIC RESONATORS

Note: Use of a series cut crystal may give a

frequency out of the crystal manufacturer’s

specifications.

Typi cal C apacitor Values Used:

Mode Freq OSC1 OSC2

XT 455 kHz

2.0 MHz

4.0 MHz

56 pF

47 pF

33 pF

56 pF

47 pF

33 pF

HS 8.0 MHz

16.0 MHz 27 pF

22 pF 27 pF

22 pF

Capacitor values are for design guidance only.

These capacitors were tested with the resonators

listed below for basic start-up and operation. These

values are not optimized.

Dif ferent cap acitor values may be required to prod uce

acceptable oscillator operation. The user should test

the performance of the oscillator over the expected

VDD and temperature range for the application.

See the notes following Table 2-2 for additional

information.

Reson ators U sed :

455 kHz 4.0 MHz

2.0 MHz 8.0 MHz

16.0 MHz

Note 1: See Table 2-1 and Table 2-2 for initial

value s of C1 and C2.

2: A series resistor (RS) may be required for

AT strip cu t crystals.

3: RF varies with the oscillator mode chosen.

C1(1)

C2(1)

XTAL

OSC2

OSC1

RF(3)

Sleep

Logic

PIC18FXXXX

RS(2)

Internal

PIC18F1220/1320

TABLE 2-2: CAPACITOR SELECTION FOR

CRYSTAL OSCILLATOR

An external clock source may also be connected to the

OSC1 pin in the HS mode, as shown in Figure 2-2.

FIGURE 2-2: EXTERNAL CLOCK INPUT

OPERATION (HS OSC

CONFIGURATION)

2.3 HSPLL

A Phase Locked Loop (PLL) circuit is provided as an

option for users who wish to use a lower frequency

crystal oscillator circuit, or to clock the device up to its

highest rated frequency from a crystal oscillator. This

may be useful for customers who are concerned with

EMI due to high-frequency crystals.

The HSPL L mode make s use of the HS mode oscil lator

for freque ncies u p to 10 MH z. A PLL t hen multipl ies the

oscillator output frequency by 4 to produce an internal

clock frequency up to 40 MHz.

The PLL is enabled only when the oscillator configura-

tion bits are programmed for HSPLL mode. If

programmed for any other mode, the PLL is not

enabled.

FIGURE 2-3: PLL BLOCK DIAGRAM

Osc Type Crystal

Freq

Typical Cap acitor V al ues

Tested:

C1 C2

LP 32 kHz 33 pF 33 pF

200 kHz 15 pF 15 pF

XT 1 MHz 33 pF 33 pF

4 MHz 27 pF 27 pF

HS 4 MHz 27 pF 27 pF

8 MHz 22 pF 22 pF

20 MHz 15 pF 15 pF

Capacitor values are for design guidance only.

These capacitors were tested with the crystals listed

below fo r ba si c start-up and operat ion. These values

are not optimized.

Dif ferent capa citor values may be require d to produce

acceptable oscillator operation. The user should test

the performance of the oscillator over the expected

VDD and temperature range for the application.

See the notes following this table for additional

information. Cryst a ls Us ed:

32 kHz 4 MHz

200 kHz 8 MHz

1 MHz 20 MH z

Note 1: Higher capacitance increases the stability

of oscillator , but also increases the st art-up

time.

2: When operating below 3V VDD, or when

using certain ceramic resonators at any

voltage, it may be necessary to use the

HS mode or switch to a crystal oscillator.

3: Since each resonator/crystal has its own

characteristics, the user should consult

the resonator/crystal manufacturer for

appropriate values of external

components.

4: RS may be required to avoid overdriving

crystals with low dr iv e lev el spe ci fic ati on.

5: Always veri fy os ci lla tor pe rform an ce ov er

the VDD and temperature range that is

expected for the application.

OSC1

OSC2

Open

Clock from

Ext. System PIC18FXXXX

(HS Mode)

MUX

VCO

Loop

Filter

Crystal

Osc

OSC2

OSC1

PLL Enable

FIN

FOUT

SYSCLK

Phase

Comparator

HS Oscillator Enable

÷4

(from Configuration Register 1H)

PIC18F1220/1320

2.4 External Clock Input

The EC and ECIO Oscilla tor modes require an externa l

clock source to be conn ected to the OSC1 pi n. There is

no oscillator start-up time required after a Power-on

Reset, or after an exit from Sleep mode.

In the EC Oscillator mode, the oscillator frequency

divided by 4 is available on the OSC2 pin. This signal

may be u sed fo r te st pu rpos es , o r to s yn chroni ze oth er

logic. Figure 2-4 shows the pin connections for the EC

Oscillator mode.

FIGURE 2-4: EXTER NAL CLOCK INPUT

OPERATION

(EC CONFIGURATION)

The ECIO O sc illator mode func ti ons li ke t he EC m od e,

except that the OSC2 pin becomes an additional gen-

eral purpose I/O pin. The I/O pin becomes bit 6 of

PORTA (RA6). Figure 2-5 shows the pin connections

for the ECIO Oscillator mode.

FIGURE 2-5: EXTER NAL CLOCK INPUT

OPERATION

(ECIO CONFIGURATION)

2.5 RC Oscillator

For timing insensitive applications, the “RC” and

“RCIO” device options offer additional cost savings.

The RC oscillator frequency is a function of the supply

voltage, the resistor (REXT) and capacitor (CEXT) val-

ues and the operating temperature. In addition to this,

the oscil lator frequen cy will vary from unit to unit due to

normal manufacturing variation. Furthermore, the dif-

ference in lead frame capacitance between package

types will also affect the oscillation frequency, espe-

cially for low CEXT values. The user also needs to take

into account variation, due to tolerance of external

R and C components used. Figure 2-6 shows how the

R/C combination is connected.

In the RC Oscillator mode, the oscillator frequency

divided by 4 is available on the OSC2 pin. This signal

may be us ed fo r te st purposes, o r to s ync hro niz e oth er

logic.

FIGURE 2-6: RC OSCILLATOR MODE

The RCIO Oscillator mode (Figure 2-7) functions like

the RC mode, except that the OSC2 pin becomes an

additional general purpose I/O pin. The I/O pin

becomes bit 6 of PORTA (RA6).

FIGURE 2-7: RCIO OSCILLATOR MODE

OSC1/CLKI

OSC2/CLKO

FOSC/4

Clock from

Ext. System PIC18FXXXX

OSC1/CLKI

I/O (OSC2)

RA6

Clock from

Ext. System PIC18FXXXX

OSC2/CLKO

CEXT

REXT

PIC18FXXXX

OSC1

FOSC/4

Internal

Clock

VDD

VSS

Recommended values: 3 kΩ ≤ REXT ≤ 100 kΩ

CEXT > 20 pF

CEXT

REXT

PIC18FXXXX

OSC1 Internal

Clock

VDD

VSS

Recommended values: 3 kΩ ≤ REXT ≤ 100 kΩ

CEXT > 20 pF

I/O (OSC2)

RA6

PIC18F1220/1320

2.6 Internal Oscillator Block

The PIC18F1220/1320 devices include an internal

oscillator block, which generates two different clock

signals; either can be used as the system’s clock

source. This can eliminate the need for external

osci llator circui ts on the OSC1 and/o r OSC2 pins .

The main output (INTOSC) is an 8 MHz clock source,

which can be used to directly drive the system clock. It

also drives a postscaler, which can provide a range of

clock frequencies from 125 kHz to 4 MHz. The

INTOSC output is enabled when a system clock

frequency from 125 kHz to 8 MHz is selected.

The other clock source is the internal RC oscillator

(INTRC), which provides a 31 kHz output. The INTRC

oscillator is enabled by selecting the internal oscillator

block as the system clock source, or when any of the

following are enabled:

• Power-up Timer

• Fail-Safe Clock Monitor

• Watchdog Timer

• Two-Speed S t a r t-up

These features are discussed in greater detail in

Section 19.0 “Special Features of the CPU”.

The clock source frequency (INTOSC direct, INTRC

direct or INTOSC postscaler) is selected by configuring

the IRCF bits of the OSCCON register (Register 2-2).

2.6.1 INTIO MODES

Using the internal oscillator as the clock source can

elimin ate the ne ed for up t o two extern al oscil lator pins ,

which can then be used for digital I/O. Two distinct

configurations are available:

• In INTIO1 mode, the OSC2 pin outputs FOSC/4,

while OSC1 fu nc tio ns as RA 7 fo r dig it a l in put and

output.

• In INTIO2 mode, OSC1 functions as RA7 and

OSC2 functions as RA6, both for digital input and

output.

2.6.2 INTRC OUTPUT FREQUENCY

The internal oscillator block is calibrated at the factory

to produce an INTOSC output frequency of 8.0 MHz

(see Table 22-6). This changes the frequency of the

INTRC source from its nominal 31.25 kHz. Peripherals

and features that depend on the INTRC source will be

affected by this shift in frequency.

Once set during factory calibration, the INTRC

frequency will remain within ±2% as temperature and

VDD change across their full specified operating

ranges.

2.6.3 OSCTUNE REGISTER

The internal oscillator’s output has been calibrated at

the factory, but can be adjusted in the user’s applica-

tion . Thi s is do ne by writi ng to the OSCTUN E regi ster

(Register 2-1). The tuning sensitivity is constant

throughout the tuning range.

When the O SC TUN E reg is ter is mo di fied , the IN T O SC

and INTRC frequencies will begin shifting to the new

frequency. The INTRC clock will reach the new

frequency within 8 clock cycles (approximately

8*32μs = 256 μs). The INTOSC clock will stabilize

within 1 ms. Code exec ution c ontinues during th is shift.

There is no indication that the shift has occurred.

Operation of features that depend on the INTRC clock

source frequency, such as the WDT, Fail-Safe Clock

Monitor and peripherals, will also be affected by the

change in freq uency.

PIC18F1220/1320

2.7 Clock Sources and Oscillator

Switching

Like previous PIC18 devices, the PIC18F1220/1320

devices include a feature that allows the system clock

source to be switched from the main oscillator to an

alternate low-frequency clock source. PIC18F1220/

1320 devices offer two alternate clock sources. When

enabled, these give additional options for switching to

the various power managed operating modes.

Essentially, there are three clock sources for these

devices:

• Primary oscillators

• Secondary oscillators

• Internal oscillator block

The primary oscillators include the External Crystal

and Resonator modes, the External RC modes, the

External Clock modes and the internal oscillator block.

The par ticula r mode is defin ed on POR by the content s

of Configuration Register 1H. The details of these

modes are covered earlier in this chapter.

The secondary oscillat ors are those external sources

not connected to the OSC1 or OSC2 pins. These

sources may continue to operate even after the

controller is placed in a power managed mode.

PIC18F1220/1320 devices offer only the Timer1

oscill ator as a seconda ry oscilla tor . This oscill ator , in all

power managed modes, is often the time base for

function s suc h as a real-time clock.

Most often, a 32.768 kHz watch crystal is connected

between the RB6/T1OSO and RB7/T1OSI pins. Like

the LP mode oscillator circuit, loading capacitors are

also connected from each pin to ground. These pins

are also used during ICSP operations.

The Timer1 oscillator is discussed in greater detail in

Section 12.2 “Timer1 Oscillator”.

In additio n to being a primary clock source, the internal

oscillator block is available as a power managed

mode cl oc k s ourc e. The INTRC source is also us ed as

the clock source for several special features, such as

the WDT and Fail-Safe Clock Monitor.

The clock sources for the PIC18F1220/1320 devices

are shown in Figure 2-8. See Section 12.0 “Timer1

Module” for furth er details of the T imer1 osci llator . See

Section 19.1 “Configuration Bits” for configuration

U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

—— TUN5 TUN4 TUN3 TUN2 TUN1 TUN0

bit 7 bit 0

bit 7-6 Unimplemented: Read as ‘0’

bit 5-0 TUN<5:0>: Frequency Tuning bits

011111 = Maximum frequency

• •

000001

000000 = Center frequency. Oscillator module is running at the calibrated frequency.

111111

• •

100000 = Minimum frequency

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

2.7.1 OSCILLATOR CONTROL REGISTER

The OSCCON register (Register 2-2) controls several

aspects of the system clock’s operation, both in full

power operation and in power managed modes.

The System Clock Select bits, SCS1:SCS0, select the

clock source that is used when the device is operating in

power managed modes. The available clock sources are

the primary cl ock (defined in Configuration Register 1H),

the secondary clock (Timer1 oscillator) and the internal

oscillator block. The clock selection has no effect until a

SLEEP instruction is executed and the device enters a

power managed mode of operation. The SCS bits are

cleared on all forms of Reset.

The Inter nal Oscillator Select bit s, IRCF2:IRCF0, select

the freque ncy o utput o f the in ternal o scill ator bl ock th at

is use d to driv e th e sys tem cl ock. The c hoi ces a re t he

INTRC source, the INTOSC source (8 MHz), or one of

the six frequencies derived from the INTOSC

postscaler (125 kHz to 4 MHz). If the internal oscillator

block is supplying the system clock, changing the

states of these bits will have an immediate change on

the internal oscillator’s output.

The OSTS, IO FS an d T1 R UN bits indic ate whic h cl oc k

source is currently providing the system clock. The

OSTS indicates that the Oscillator Start-up Timer has

timed ou t and the prima ry clock i s providin g the system

clock in Primary Clock modes. The IOFS bit indicates

when the internal oscillator block has stabilized and is

providing the system clock in RC Clock modes or

during Two-Speed Start-ups. The T1RUN bit

(T1CON<6>) indicates when the Timer1 oscillator is

provi ding th e syste m cloc k in Seco ndary Clock mo des.

In power managed modes, only one of these three bits

will be set at any time. If none of these bits are set, the

INTRC is providing the system clock, or the internal

oscillator block has just started and is not yet stable.

The IDLEN bit controls the selective shutdown of the

controller ’s CPU in power managed modes. The uses

of these bits are discussed in more detail in

Section 3.0 “Power Managed Modes”.

FIGURE 2-8: PIC18F1220/1320 CLOCK DIAGRAM

Note 1: The Timer1 oscillator must be enabled to

select the secondary clock source. The

T imer 1 oscilla tor is enable d by setting the

T1OSCEN bit in the T ime r1 Control re gis-

ter (T1CON<3>). If the Timer1 oscillator

is not en abl ed, then any at tem pt to se lec t

a secondary clock source when

executing a SLEEP instruction will be

ignored.

2: It is recommended that the Timer1 oscil-

lator be operating and stable before exe-

cuting the SLEEP instruction or a very

long delay may occur while the Timer1

oscillator starts.

PIC18F1220/1320

4 x PLL

CONFIG1H<3:0>

Secondary Oscillator

T1OSCEN

Enable

Oscillator

T1OSO

T1OSI

Clock Source Option

for Other Modules

OSC1

OSC2

Sleep

Primary Oscillator

HSPLL

LP, XT, HS, RC, EC

T1OSC

CPU

Peripherals

IDLEN

Postscaler

MUX

4 MHz

2 MHz

1 MHz

500 kHz

125 kHz

250 kHz

OSCCON<6:4>

111

110

101

100

011

010

001

000

31 kHz

INTRC

Source

Internal

Oscillator

Block

WDT, FSCM

8 MHz

Internal Oscillator

(INTOSC)

OSCCON<6:4>

Clock

Control OSCCON<1:0>

PIC18F1220/1320

R/W-0 R/W-0 R/W-0 R/W-0 R(1) R-0 R/W-0 R/W-0

IDLEN IRCF2 IRCF1 IRCF0 OSTS IOFS SCS1 SCS0

bit 7 bit 0

bit 7 IDLEN: Idle Enable bits

1 = Idle mode enabled; CPU core is not clocked in power managed modes

0 = Run mode enabled; CPU core is c lock ed in Run modes, but not Sle ep mode

bit 6-4 IRCF2:IRCF0: Internal Oscillator Frequency Select bits

111 = 8 MHz (8 MHz source drives clock directly)

110 = 4 MHz

101 = 2 MHz

100 = 1 MHz

011 = 500 kHz

010 = 250 kHz

001 = 125 kHz

000 = 31 kHz (INTRC source drives clock directly)

bit 3 OSTS: Oscillator Start-up Time-out Status bit

1 = Oscillator Start-up Timer time-out has expired; primary oscillator is running

0 = Oscillator Start-up Timer time-out is running; primary oscillator is not ready

bit 2 IOFS: INTOSC Frequency Stable bit

1 = INTOSC frequency is stable

0 = INTOSC frequency is not stable

bit 1-0 SCS1:SCS0: System Clock Select bits

1x = Internal oscillator block (RC modes)

01 = Timer1 oscillator (Secondary modes)

00 = Primary oscillator (Sleep and PRI_IDLE modes)

Note 1: Depends on state of the IESO bit in Configuration Register 1H.

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320
DS39605D-page 18 © 2006 Microchip Technology Inc.
2.7.2 OSCILLA TOR TR ANSIT ION S
The PIC18F1220/1320 devices contain circuitry to
prevent clocking “glitches” when switching between
clock sources. A short pause in the system clock
occurs  during the clo ck switch. Th e length of thi s pause
is between 8 and 9 clock periods of the new clock
source. This ensures that the new clock source is
stable and that its pulse width will not be less than the
shortest pulse width of the two clock sources.
Clock transitions are discussed in greater detail in
Section 3.1.2 “Entering Power Managed Modes”.
2.8 Effects of Power Managed Modes 
on the Various Clock Sources
When the device executes a SLEEP instruction, the
system is switched to one of the power managed
modes, depending on the state of the IDLEN and
SCS1:SCS0 bits of the OSCCON register. See
Section 3.0 “Power Managed Modes” for details.
When PRI_IDLE mode is selected, the designated pri-
mary oscillator continues to run without interruption.
For all other power managed modes, the oscillator
using the OSC1 pin is disabled. The OSC1 pin (and
OSC2  pin, if us ed by th e oscillat or) will  stop oscil lating. 
In Secondary Clock modes (SEC_RUN and
SEC_IDLE), the Timer1 oscillator is operating and
providing the system clock. The Timer1 oscillator may
also run in all power managed modes if required to
clock Timer1 or Timer3.
In Internal Oscillator modes (RC_RUN and RC_IDLE),
the internal oscillator block provides the system clock
source. The INTRC output can be used directly to
provide the system clock and may be enabled to
support various special features, regardless of the
power managed mode (see Section 19.2 “Watchdog
Time r (WDT)” thro ugh Sect ion 19.4  “Fail-Sa fe Clock
Monitor”). The INT OSC out put at 8 MH z may be used
directly to clock the system, or may be divided down
first.  The INT OSC output is disabl ed if the system cl ock
is provided directly from the INTRC output.
If the Sleep mode is selected, all clock sources are
stopped. Since all the transistor switching currents
have been stopped, Sleep mode achieves the lowest
current consumption of the device (only leakage
currents).
Enabling any on-chip feature that will operate during
Sleep will  increase the  current cons umed during Sl eep.
The INTRC is required to support WDT operation. The
Timer1 oscillator may be operating to support a real-
time cl ock. Ot her fea tures may be  operat ing that d o not
require a system clock source (i.e., INTn pins, A/D
conversions and others).
2.9 Power-up Delays
Power-up delays are controlled by two timers, so that
no exte rna l Reset circuitry is re qui red  fo r m os t a ppl ic a-
tions. The delays ensure that the device is kept in
Reset  until the  device powe r supply i s stable  under nor-
mal circumstances and the primary clock is operating
and stable. For additional information on power-up
delays, see Sections 4.1 through 4.5.
The first timer is the Power-up Timer (PWRT), which
provides a fixed delay on power-up (parameter 33,
Table 22-8) if enabled in Configuration Register 2L.
The second timer is the Oscillator Start-up Timer
(OST), intended to keep the chip in Reset until the
crystal oscillator is stable (LP, XT and HS modes). The
OST does this by counting 1024 oscillator cycles
before allowing the oscillator to clock the device.
When the HSPLL Oscillator mode is selected, the
device is kept in Reset for an additional 2 ms following
the HS mode OST delay, so the PLL can lock to the
inco mi ng cl ock  frequ enc y.
There is a delay of 5 to 10 μs following POR while the
controller becomes ready to execute instructions. This
delay runs concurrently with any other delays. This
may be  the  onl y  delay that oc cu rs  wh en  any  o f the  EC ,
RC or INTIO modes are used as the primary clock
source.
TABLE 2-3: OSC1 AND OSC2 PIN STATES IN SLEEP MODE  
Oscillator Mode OSC1 Pin OSC2 Pin
RC, INTIO1 Floating, external resistor should pull high At logic low (clock/4 output)
RCIO, INTIO2 Floating, external resistor should pull high Configured as PORTA, bit 6
ECIO Floating, pulled by external clock Configured as PORTA, bit 6
EC Floating, pulled by external clock At logic low (clock/4 output)
LP, XT and HS Feedback inverter disabled at quiescent 
voltage level Feedback inverter disabled at quiescent 
voltage level
Note: See Table 4-1 in Section 4.0 “Reset” for time-outs due to Sleep and MCLR Reset.

PIC18F1220/1320

3.0 POWER MANAGED MODES

The PIC 18F122 0/1320 devic es o ffe r a tot al o f six oper-

ating modes for more efficient power management

(see Table 3-1). These provide a variety of options for

selective power conservation in applications where

resources may be limited (i.e., battery powered

devices).

There are three categories of power managed modes:

• Sleep mode

• Idle mo des

• Run modes

These categories define which portions of the device

are clo cked and some times , what sp eed. The Ru n and

Idle modes may use any of the three available clock

sources (primary, secondary or INTOSC multiplexer);

the Sleep mode does not use a clock source.

The clock switching feature offered in other PIC18

devices (i.e., using the Timer1 oscillator in place of the

primary oscillator) and the Sleep mode offered by all

PICmicro® devices (where all system clocks are

stopped) are both offered in the PIC18F1220/1320

devices (SEC_RUN and Sleep modes, respectively).

However, additional power managed modes are avail-

able tha t allow t he user grea ter flexib ility in d eterminin g

what portions of the device are operating. The power

managed modes are event driven; that is, some

specific event must occur for the device to enter or

(more particularly) exit these operating modes.

For PIC18F1220/1320 devices, the power managed

modes are invoked by using the existing SLEEP

instruction. All modes exit to PRI_RUN mode when trig-

gered by an interrupt, a Reset or a WDT time-out

(PRI_RUN mode is the normal full power execution

mode; the C PU and peri phe rals are cl ock ed by the p ri-

mary oscillator source). In addition, power managed

Run modes may also exit to Sleep mode, or their

corresponding Idle mode.

3.1 Selecting Power Managed Modes

Selecting a power managed mode requires deciding if

the CPU is to be clocked or not and selecting a clock

source. The IDLEN bit controls CPU cloc king, while the

SCS1:SCS0 bits select a clock source. The individual

modes, bit settings, clock sources and affected

modules are summarized in Table 3-1.

3.1.1 CLOCK SOURCES

The clock source is selected by setting the SCS bits of

the OSCCON register (Register 2-2). Three clock

sources are available for use in power managed Idle

modes: the primary clock (as configured in Configuration

and the internal oscillator block. The secondary and

internal oscillator block sources are available for the

power managed modes (PRI_RUN mode is the normal

full power execution mode; the CPU and peripherals are

clocked by the primary os cilla to r source).

TABLE 3-1: POWER MANAGED MODES

Mode

OSCCON Bits Module Clocking

Available Clock and Oscillator Source

IDLEN

<7> SCS1:SCS0

<1:0> CPU Peripherals

Sleep 000 Off Off None – All clocks are disabled

PRI_RUN 000Clocked Clocked Primary – LP, XT, HS, HSPLL, RC, EC, INTRC(1)

This is the normal full pow er execution mode.

SEC_RUN 001Clocked Clocked Secondary – Timer1 Oscillator

RC_RUN 01xClocked Clocked Internal Oscillator Block(1)

PRI_IDLE 100 Off Clocked Primary – LP, XT, HS, HSPLL, RC, EC

SEC_IDLE 101 Off Clocked Secondary – Timer1 Oscillator

RC_IDLE 11x Off Clocked Internal Oscillator Block(1)

Note 1: Includes INTOSC and INTOSC postscaler, as well as the INTRC source.

PIC18F1220/1320

3.1.2 ENTERING POWER MANAGED

MODES

In general, entry, exit and switching between power

managed clock sources requires clock source

switching. In each case, the sequence of events is the

same.

Any change in the power managed mode begins with

loading the OSCCON register and executing a SLEEP

instruction. The SCS1:SCS0 bits select one of three

power managed clock sources; the primary clock (as

defined in Configuration Register 1H), the secondary

clock (the Timer1 oscillator) and the internal oscillator

block (use d in RC modes) . Modi fyi ng th e SCS bi ts will

have no effect until a SLEEP instruction is executed.

Entry to the power managed mode is triggered by the

execution of a SLEEP instruction.

Figure 3-5 shows how the system is clocked while

switching from the primary clock to the Timer1 oscilla-

tor. When the SLEEP instruction is executed, clocks to

the device are stopped at the beginning of the next

instruction cycle. Eight clock cycles from the new clock

source are counted to synchronize with the new clock

source. After eight clock pulses from the new clock

source are counted, clocks from the new clock source

resume clocking the system. The actual length of the

paus e is betwe en eight and nine cl ock peri ods from th e

new clock source. This ensures that the new clock

source is stab le a nd th at its puls e w idth will no t be l es s

than the shortest pulse width of the two clock sources.

Three bi t s in dicat e the current cloc k so urce: OSTS an d

IOFS in the OSCCON register and T1RUN in the

T1CON re gister. Only one of the se bit s will be se t while

in a power managed mode. When the OSTS bit is set,

the primary clock is providing the system clock. When

the IOFS bit is set, the INTOSC output is providing a

stable 8 MHz clock source and is providing the system

clock. When the T1RUN bit is set, th e Timer1 oscillator

is providing the system clock. If none of these bits are

set, then either the INTRC clock source is clocking the

system, or the INTOSC source is not yet stable.

If the internal oscillator block is configured as the pri-

mary clock source in Configuration Register 1H, then

both the OSTS and IOFS bits may be set when in

PRI_RUN or PRI_IDLE modes. This indicates that the

primary clock (INTOSC output) is generating a stable

8 MHz output. Entering an RC power managed mode

(same frequency) would clear the OSTS bit.

3.1. 3 MULTIPLE SLEEP COMMANDS

The power managed mode that is invoked with the

SLEEP instruction is determined by the settings of the

IDLEN and SCS bits at the time the instruction is exe-

cuted. If another SLEEP instruction is executed, the

device will enter the power managed mode specified b y

these same bits at that time. If the bits have changed,

the device will enter the new power managed mode

specified by the new bit settings.

3.1.4 COMPARISONS BETWEEN RUN

AND IDLE MODES

Clock source selection for the Run modes is identical to

the corresponding Idle modes. When a SLEEP instruc-

tion is executed, the SCS bits in the OSCCON register

are used to switch to a different clock source. As a

result, i f the re i s a ch ange of cloc k s ource at the time a

SLEEP instruction is executed, a clock switch will occu r.

In Idle modes, the CPU is not clocked and is not run-

ning. In Run modes, the C PU i s cl oc ked a nd ex ecuting

code. This difference modifies the operation of the

WDT when it times ou t. I n Id le mo des , a WDT tim e-o ut

results in a wake from power managed modes. In Run

modes, a WDT time-out results in a WDT Reset (see

Table 3-2).

During a wake-up from an Idle mode, the CPU starts

executing code by entering the corresponding Run

mode unt il the prima ry clock becomes read y. When the

primary cloc k bec omes ready, the cloc k so urce i s aut o-

matica lly switched to the prim ary clock. The I DLEN and

SCS bit s are un ch ang ed duri ng a nd af ter th e w ake-u p.

Figur e 3-2 shows how the system is clocked during the

clock source switch. The example assumes the device

was in SEC_IDLE or SEC_RUN mode when a wake is

triggered (the primary clock was configured in HSPLL

mode).

Note 1: Caution should be used when modifying a

single IRCF bit. If VDD is less than 3V, it is

possible to select a higher clock speed

than is supported by the low VDD.

Improper device operation may result if

the VDD/FOSC specifications are violated.

2: Executing a SLEEP instruction does not

necessarily place the device into Sleep

mode; executing a SLEEP instruction is

simply a tri gger to place th e controller in to

a power managed mode selected by the

OSCCON register, one of which is Sleep

mode.

PIC18F1220/1320

3.2 Sleep Mode

The power managed Sleep mode in the PIC18F1220/

1320 devices is identical to that offered in all other

PICmicro microcontrollers. It is entered by clearing the

IDLEN and SCS1:SCS0 bits (this is the Reset state)

and executing the SLEEP instr uctio n. T his shuts down

the primary oscillator and the OSTS bit is cleared (see

Figure 3-1).

When a wake even t occurs i n Sleep mo de (by int errupt,

Reset or WD T time-out), the sy stem wi ll not be cloc ked

until the primary clock source becomes ready (see

Figure 3-2), or it will be clocked from the internal

oscillator block if either the Two-Speed Start-up or the

Fail-Safe Clock Moni tor are enabled (see Section 19.0

“Special Features of the CPU”). In either case, the

OSTS bit is set whe n the primary c loc k is pro vi din g th e

system clocks. The IDLEN and SCS bits are not

affec ted by the wake-up.

3.3 Idle Modes

The IDLEN bit allows the microc ontroller ’s CPU to be

selectively shut down while the peripherals continue to

operat e. Clearing ID LEN allows the C PU to be cl ocked.

Setting IDLEN disables clocks to the CPU, effectively

stopping program execution (see Register 2-2). The

peripherals continue to be clocked regardless of the

setting of the IDLEN bit.

There is one exception to how the IDLEN bit functions.

When all the low-power OSCCON bits are cleared

(IDLEN:SCS1:SCS0 = 000), the device enters Sleep

mode upon the execution of th e SLEEP instruction. This

is both the Reset state of the OSCCON register and the

setting that selects Sleep mode. This maintains

compatibility with other PICmicro devices that do not

offer power managed modes.

If the Idle Enab le bit, IDLEN (OSCCON<7>), i s set to a

‘1’ when a SLEEP instruction is executed, the

peripherals will be clocked from the clock source

select ed using the SCS1:SCS0 bit s; however, the CPU

will not be clocked. Since the CPU is not executing

instructions, the only exits from any of the Idle modes

are by interrupt, WDT time-out or a Reset.

When a wake event occurs, CPU execution is delayed

approxi mately 10 μs whil e it becomes ready to e xecute

code. When the CPU begins executing code, it is

clocked by the same clock source as was selected in

the power managed mode (i.e., when waking from

RC_IDLE mode, the internal oscillator block will clock

the CPU an d periphe rals until the primary c lock so urce

becomes ready – this is essentially RC_RUN mode).

This continues until the primary clock source becomes

ready. When the primary clock becomes ready, the

OSTS bit is set and the system clock source is

switched to the primary clock (see Figure 3-4). The

IDLEN and SCS bits are not affected by the wake-up.

While in any Idle mode or the Sleep mode, a WDT

time-out will result in a WDT wake-up to full power

operation.

TABLE 3-2: COMPARISON BETWEEN POWER MANAGED MODES

Power

Managed

Mode CPU is Clocked by ... WDT Time-out

causes a ... Peripherals are

Clocked by ...

Clock during Wake-up

(while primary becomes

ready)

Sleep Not clocked (not running) Wake-up Not clocked None or INTOSC multiplexer

if Two-Speed Start-up or

Fail-Sa fe Cl ock Monitor are

enabled

Any Idle mode Not clocked (not running) Wake-up Primary, Secondary or

INTOSC multiplexer Unchanged from Idle mode

(CPU operates as in

corresponding Run mode)

Any Run mode Primary or secondary

clocks or INTOSC

multiplexer

Reset Primary or secondary

clocks or INTOSC

multiplexer

Unchanged from Run mode

PIC18F1220/1320

FIGURE 3-1: TIMING TRANSITION FOR ENTRY TO SLEEP MODE

FIGURE 3-2: TRANSITION TIMING FOR WAKE FROM SLEEP (HSPLL)

Q4Q3Q2

OSC1

Peripheral

Sleep

Program

Q1Q1

Counter

Clock

CPU

Clock

PC + 2PC

Q3 Q4 Q1 Q2

OSC1

Peripheral

Program PC

PLL Clock

Q3 Q4

Output

CPU Clock

Q1 Q2 Q3 Q4 Q1 Q2

Clock

Counter PC + 8

PC + 6

Q1 Q2 Q3 Q4

Wake Event

Note 1: TOST = 1024 TOSC; T PLL = 2 ms (approx). Thes e intervals are not shown to scale.

TOST(1) TPLL(1)

OSTS bit Set

PC + 4

PC + 2

PIC18F1220/1320

3.3.1 PRI_IDLE MODE

This mode is unique among the three Low-Power Idle

modes, in that it does not disable the primary system

clock. For timing sensitive applications, this allows for

the faste st resump tion of device op eration with its more

accur ate prima ry clock sou rce, sinc e the clock s ource

does not have to “warm up” or transition from another

oscillator.

PRI_IDLE mode is entered by setting the IDLEN bit,

clearing the SCS bits and executing a SLEEP instruc-

tion. Although the CPU is disabled, the peripherals

continue to be clocked from the primary clock source

specified in Configuration Register 1H. The OSTS bit

remains set in PRI_IDLE mode (see Figure 3-3).

When a wake event occurs, the CPU is clocked from

the primary clock source. A delay of approximately

10 μs is required between the wake event and code

execution starts. This is required to allow the CPU to

becom e re ady to exec ute inst ruct ion s. Af ter t he wa ke-

up, the O STS bit rem ains se t. The IDLE N and SCS bit s

are not affected by the wake-up (see Figure 3-4).

FIGURE 3-3: TRANSITION TIMING TO PRI_IDLE MODE

FIGURE 3-4: TRANSITION TIMING FOR WAKE FROM PRI_IDLE MODE

Peripheral

Program PC PC + 2

OSC1

Q3 Q4 Q1

CPU Clock

Clock

Counter

OSC1

Peripheral

Program PC

CPU Clock

PC + 2

Q1 Q3 Q4

Clock

Counter

Wake Eve nt

CPU Start-up Delay

PIC18F1220/1320

3.3.2 SEC_ID LE MODE

In SEC_IDLE mode, the CPU is disabled, but the

peripherals continue to be clocked from the Timer1

oscillator. This mode is entered by setting the Idle bit,

modifying bits, SCS1:SCS0 = 01 and executing a

SLEEP instruction. When the clock source is switched

(see Figure 3-5) to the Timer1 oscillator, the primary

oscill ator is shut do wn, th e OSTS bit is cleared and the

T1RUN bit is set.

When a w ake event o ccurs, the pe ripherals contin ue to

be clocked from the Timer1 oscillator. After a 10 μs

delay following the wake event, the CPU begins exe-

cuting code, being clocked by the Timer1 osci llator . The

microcontroller operates in SEC_RUN mode until the

primary clock becomes ready. When the primary clock

become s ready , a clock switchback to the p rimary clock

occurs (see Figure 3-6). When the cloc k swit ch is com -

plete, the T1RUN bit is cleared, the OSTS bit is set and

the primary clock is providing the system clock. The

IDLEN and SCS bits are not affected by the wake-up.

The Timer1 oscillator continues to run.

FIGURE 3-5: TIMING TRANSITION FOR ENTRY TO SEC_IDLE MODE

FIGURE 3-6: TIMING TRA NSITION FOR WAKE FROM SEC_RUN MODE (HSPLL)

Note: The Timer1 oscillator should already be

running prior to entering SEC_IDLE mode.

If the T1OSCEN bit is not set when the

SLEEP instruction is executed, the SLEEP

instruction will be ignored and entry to

SEC_IDLE mode will not occur. If the

Timer1 oscillator is enabled, but not yet

running, peripheral clocks will be delayed

unti l th e os cilla tor has s tarte d; i n su ch sit -

uations, initial oscillator operation is far

from stable and unpredictable operation

may re sult.

Q4Q3Q2

OSC1

Peripheral

Program

T1OSI

Counter

Clock

CPU

Clock

PC + 2PC

12345678

Clock Transi tion

Q1 Q3 Q4

OSC1

Peripheral

Program PC PC + 2

T1OSI

PLL Clock

PC + 6

Output

Q3 Q4 Q1

CPU Clock

PC + 4

Clock

Counter

Q2 Q2 Q3

Note 1: TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale.

Wake from Interrupt Event

TPLL(1)

12345678

Clock Transition

OSTS bit Set

TOST(1)

PIC18F1220/1320

3.3.3 RC_IDLE MODE

In RC_ID LE mode, the CPU is di sabled, but the periph-

erals co nti nue to b e c loc ke d fro m the internal oscilla tor

block using the INTOSC multiplexer. This mode allows

for cont rollable power c onservation during Idle periods.

This mode is entered by setting the IDLEN bit, setting

SCS1 (SCS0 is ignored) and executing a SLEEP

instruction. The INTOSC multiplexer may be used to

select a higher clock frequency by modifying the IRCF

bits be for e ex ecut in g the SLEEP instruction. When the

clock source is switched to the INTOSC multiplexer

(see Figure 3-7), the primary oscillator is shut down

and the OSTS bit is cleared.

If the IRCF bits are set to a non-zero value (thus,

enabling the INTOSC output), the IOFS bit becomes

set after the INTOSC output becomes stable, in about

1 ms. Clocks to the peripherals continue while the

INTOSC source stabilizes. If the IRCF bits were

previously at a non-zero value before the SLEEP

instruction was executed and the INTOSC source was

already st ab le, the IO FS bi t will rema in s et. If th e IRCF

bits are all cl ear, the INTOSC o utput is n ot enable d and

the IOFS bit will remai n clear; there will be no indicatio n

of the current clock source.

When a w ake event o ccurs, the pe ripherals contin ue to

be clocked fro m the INT OSC mu lti ple xe r. After a 10 μs

delay following the wake event, the CPU begins exe-

cuting co de, bein g clock ed by the INTOSC multi plexe r.

The microcontroller operates in RC_RUN mode until

the primary clock becomes ready. When the primary

clock becomes ready , a clock switchback to the primary

clock occurs (see F igure 3-8). W hen the clock sw itch is

complete, the IOFS bit is cleared, the OSTS bit is set

and the primary clock is providing the system clock.

The ID LEN a nd SC S b it s a re not affec ted by t he wake-

up. The INTRC source will continue to run if either the

WDT or the Fail-Safe Clock Monitor is enabled.

FIGURE 3-7: TIMING TRANSITION TO RC_IDLE MODE

FIGURE 3-8: TIMING TRANSITION FOR W AKE FROM RC_RUN MODE (RC_RUN TO PRI_RUN)

Q4Q3Q2

OSC1

Peripheral

Program

INTRC

Counter

Clock

CPU

Clock

PC + 2PC

12345678

Clock Transition

Q1 Q3 Q4

OSC1

Peripheral

Program PC PC + 2

INTOSC

PLL Clock

PC + 6

Output

Q3 Q4 Q1

CPU Clock

PC + 4

Clock

Counter

Q2 Q2 Q3

Note 1: TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale.

Wake from Interrupt Event

TOST(1) TPLL(1)

12345678

Clock Transition

OSTS bit Set

Multiplexer

PIC18F1220/1320

3.4 Run Modes

If the IDLEN bit is clear when a SLEEP instruction is

executed, the CPU and peripherals are both clocked

from the source selected using the SCS1:SCS0 bits.

While t hese operating mo des may not af ford the power

conservation of Idle or Sleep modes, they do allow the

device to continue executing instructions by using a

lower frequency clock source. RC_RUN mode also

offers the possibility of executing code at a frequency

great er than the primary cloc k .

Wake-up from a power managed Run mode can be

triggered by an interrupt, or any Reset, to return to full

power o pera tio n. As the CPU i s exec uti ng c od e in Run

modes, several additional exits from Run modes are

possib le. They inclu de exit to Sleep mode , exit to a cor-

responding Idle mode and exit by executing a RESET

instruction. While the device is in any of the power

managed Run modes, a WDT time-out will result in a

WDT R eset.

3.4.1 PRI_RUN MODE

The PRI_RUN mode is the normal full power execution

mode. If the SLEEP instruction is never executed, the

microc ontroller opera tes in this mode (a SLEEP instruc-

tion is executed to enter all other power managed

modes). All other power managed modes exit to

PRI_RUN mode when an interrupt or WDT time-out

occur.

There is no entry to PRI_RUN mode. The OSTS bit is

set. The IOFS bit may be set if the internal oscillator

block is the primary clock source (see Section 2.7.1

“Oscillator Control Register”).

3.4.2 SEC_RUN MODE

The SEC_RUN mode is the compatible mode to the

“clock switching” feature offered in other PIC18

devices. In this mode, the CPU and peripherals are

clock ed from the T imer1 os cillator. This gives users the

option of lower power consumption while still using a

high accuracy clock source.

SEC_RUN mode is entered by clearing the IDLEN bit,

setting SCS1:SCS0 = 01 and executing a SLEEP

instr ucti on. Th e syste m clock source is switched to the

Timer1 oscillator (see Figure 3-9), the primary oscilla-

tor is shut down, the T1RUN bit (T1CON<6>) is set and

the OSTS bit is cleared.

When a wake event occurs, the peripherals and CPU

continue to be clocked from the Timer1 oscillator while

the primary clock is started. When the primary clock

become s ready , a clock switchback to the p rimary clock

occurs (see Figure 3-6). When the cloc k swit ch is com -

plete, the T1RUN bit is cleared, the OSTS bit is set and

the primary clock is providing the system clock. The

IDLEN and SCS bits are not affected by the wake-up.

The Timer1 oscillator continues to run.

Firmware can force an exit from SEC_RUN mode. By

clearing the T1OSCEN bit (T1CON<3>), an exit from

SEC_RUN back to normal full power operation is trig-

gered. The Timer1 oscillator will continue to run and

provide the system clock, even though the T1OSCEN

bit is cleared. The primary clock is started. When the

primary clock becomes ready , a clock switchback to the

primary clock occurs (see Figure 3-6). When the clock

switch i s compl ete, the T imer1 oscil lator is disabled, the

T1RUN bit is cleared, the OSTS bit is set and the pri-

mary clock is providing the system clock. The IDLEN

and SCS bits are not affected by the wake-up.

FIGURE 3-9: TIMING TRANSITION FOR ENTRY TO SEC_RUN MODE

Note: The Timer1 oscillator should already be

running pri or to entering SEC_RUN mod e.

If the T1OSCEN bit is not set when the

SLEEP instruction is executed, the SLEEP

instruction will be ignored and entry to

SEC_RUN mode will not occur. If the

Timer1 oscillator is enabled, but not yet

running, system clocks will be delayed

until the oscillator has started; in such

situations, initial oscillator operation is far

from stable and unpredictable operation

may re sult.

Q4Q3Q2

OSC1

Peripheral

Program

T1OSI

Counter

Clock

CPU

Clock

PC + 2PC

12345678

Clock Transition

Q4Q3

Q2 Q1 Q3

PC + 2

PIC18F1220/1320

3.4.3 RC_RUN MODE

In RC_RUN mode, the CPU and peripherals are

clocked from the internal oscillator block using the

INTOSC multiplexer and the primary clock is shut

down. When using the INTRC source, this mode pro-

vides the best power conservation of all the Run

modes, while still executing code. It works well for user

applic ations whic h are n ot highly tim ing sens itive, or d o

not requ ire high-speed clocks at all times.

If the primary clock source is the internal oscillator

block (ei ther of the INTIO1 or INTIO 2 oscill ators), there

are no distinguishable differences between PRI_RUN

and RC_RUN modes during execution. However, a

clock switch delay will occur during entry to and exit

from RC_RUN mode. Therefore, if the primary clock

source is the internal oscillator block, the use of

RC_RUN mode is not recommended.

This m ode i s e nte red by c lea rin g th e ID LEN b it, se ttin g

SCS1 (SCS0 is ignored) and executing a SLEEP

instruction. The IRCF bits may select the clock

frequency before the SLEEP instruction is executed.

When the clock source is switched to the INTOSC

multiplexer (see Figure 3-10), the primary oscillator is

shut down and the OSTS bit is cleared.

The IRCF bits may be modified at any time to immedi-

ately change the system clock speed. Executing a

SLEEP instruction is not required to select a new clock

frequency from the INTOSC multiplexer.

If the IRCF bits are all clear, the INTOSC output is not

enabled and the IOFS bit wi ll remain clear; t here will b e

no indication of the current clock source. The INTRC

source is providing the system clocks.

If the IRCF bits are changed from all clear (thus,

enabling the INTOSC output), the IOFS bit becomes

set after the INTOSC output bec omes st able. Cloc ks to

the system continue while the INTOSC source

stabilizes, in approximately 1 ms.

If the IRCF bits were previously at a non-zero value

before the SLEEP instruction was executed and the

INTOSC source was already stable, the IOFS bit will

remain set.

When a wa ke event occurs, the system conti nues to be

clock ed from the INT OSC multi plexer whi le the prim ary

clock is started. When the primary clock becomes

ready, a clock switch to the primary clock occurs (see

Figure 3-8). When the clock switch is complete, the

IOFS bit is c leared, the O STS bit is se t and the prim ary

clock is providing the system clock. The IDLEN and

SCS bits are not affected by the wake-up. The INTRC

source will continue to run if either the WDT or the

Fail- Safe Cloc k Mo nito r is enab led .

FIGURE 3-10: TIMING TRA NSITION TO RC_RUN MODE

Note: Cau tio n s hou ld be u se d w he n m odi fy ing a

single IRCF bit. If VDD is less than 3V, it is

possible to select a higher clock speed

than is supported by the low VDD.

Improper device operation may result if

the VDD/FOSC specifications are violated.

Q3Q2Q1

OSC1

Peripheral

Program

INTRC

Counter

Clock

CPU

Clock

PC + 2PC

12345678

Clock Transition

Q3Q2Q1 Q4 Q2Q1 Q3

PC + 4

PIC18F1220/1320

3.4.4 EXIT TO IDLE MODE

An exit from a power managed Run mode to its

corresponding Idle mode is executed by setting the

IDLEN bit and executing a SLEEP instruction. The CPU

is halted at the beginning of the instructi on following the

SLEEP instruction. There are no changes to any of the

clock source status bits (OSTS, IOFS or T1RUN).

While th e CPU is halte d, the periphe rals c ontin ue to b e

clocked from the previously selected clock source.

3.4.5 EXIT TO SLEEP MODE

An exit from a power managed Run mode to Sleep

mode is executed by clearing the IDLEN and

SCS1:SCS0 bits and executing a SLEEP instruction.

The code is no different than the method used to invoke

Sleep mode from the normal operating (full power)

mode.

The primary clock and internal oscillator block are

disabled. The INTRC will continue to operate if the

WDT is enabled. The Timer1 oscillator will continue to

run, if enabled in the T1CON register (Register 12-1).

All clock source status bits are cleared (OSTS, IOFS

and T1RUN).

3.5 Wake from Power Managed Modes

An exit from any of the power managed modes is trig-

gered by an interrupt, a Reset or a WDT time-out. This

section discusses the triggers that cause exits from

power managed modes. The clocking subsystem

actions are discussed in each of the power managed

modes (see Sections 3.2 through 3.4).

Device behavior during Low-Power mode exits is

summa riz ed in Table 3-3.

3.5. 1 EXIT BY INTERRUPT

Any of the available interrupt sources can cause the

device to exit a power managed mode and resume full

power operation. To enable this functionality, an inter-

rupt sou r ce mu st be e nab led by setti ng it s en able bit in

one of the IN TCON or PIE registers. Th e exit sequenc e

is initiated when the corresponding interrupt flag bit is

set. On all exits from Low-Power mode by interrupt,

code execution branches to the interrupt vector if the

GIE/GIEH bit (INTCON<7>) is set. Otherwise, code

execution continues or resumes without branching

(see Section 9.0 “Interrupts”).

Note: If application code is timing sensitive, it

should wait for the OSTS bit to become set

before continuing. Use the interval during

the low-power exit sequence (before

OSTS is set) to perform timing insensitive

“housekeeping” tasks.

PIC18F1220/1320

TABLE 3-3: ACTIVITY AND EXIT DELAY ON WAKE FROM SLEEP MODE OR ANY IDLE MODE

(BY CLOCK SOURCES)

Clock in Power

Managed Mode Primary System

Clock

Power

Managed

Mode Exit

Delay

Clock Ready

Status Bit

(OSCCON)

Activity during Wake-up from

Power Managed Mode

Exit by Interrupt Exit by Reset

Primary System

Clock

(PRI_IDLE mode)

LP, XT, HS

5-10 μs(5) OSTS CPU and peripherals

clocked by primary

clock and executing

instructions.

Not cl ocked or

Two-Speed Start-up

(if enabled)(3).

HSPLL

EC, RC, INTRC(1) —

INTOSC(2) IOFS

T1OSC or

INTRC(1)

LP, XT, HS OST OSTS CPU and peripherals

clocked by selected

power m an age d mo de

clock and executing

instructions until

primary clock source

becomes ready.

HSPLL OST + 2 ms

EC, RC, INTRC(1) 5-10 μs(5) —

INTOSC(2) 1ms

(4) IOFS

INTOSC(2)

LP, XT, HS OST OSTS

HSPLL OST + 2 ms

EC, RC, INTRC(1) 5-10 μs(5) —

INTOSC(2) None IOFS

Sleep mode

LP, XT, HS OST OSTS Not clocked or

Two-S pee d Start-up (if

enabled) unti l prim ary

clock source becomes

ready(3).

HSPLL OST + 2 ms

EC, RC, INTRC(1) 5-10 μs(5) —

INTOSC(2) 1ms

(4) IOFS

Note 1: In this instance, refers specifically to the INTRC clock source.

2: Includes both the INTOSC 8 MHz source and postscaler derived frequencies.

3: Two-Speed Start-up is covered in greater detail in Section 19 .3 “Two-Speed Start-up”.

4: Execution continues during the INTOSC stabilization period.

5: Required delay when waking from Sleep and all Idle modes. This delay runs concurrently with any other

required delays (see Section 3.3 “Idle Modes”).

PIC18F1220/1320
DS39605D-page 30 © 2006 Microchip Technology Inc.
3.5. 2 EXIT BY RESET
Normally, the device is held in Reset by the Oscillator
St art-up Timer (O ST) until th e primary clo ck (defined  in
Configuration Register 1H) becomes ready. At that
time, the OSTS bit is set and the device begins
executing code.
Code execution can begin before the primary clock
becomes ready. If either the Two-Speed Start-up (see
Section 19.3 “Two-Speed Start-up”) or Fail-Safe
Clock Monitor (see Section 19.4 “Fail-Safe Clock
Monitor”) are enabled in Configuration Register 1H,
the device may begin execution as soon as the Reset
source has cleared. Execution is clocked by the
INTOSC multiplexer driven by the internal oscillator
block. Since the OSCCON register is cleared following
all Resets, the INTRC clock source is selected. A
higher speed clock may be selected by modifying the
IRCF bits in the OSCCON register. Execution is
clocked by the internal oscillator block until either the
primary clock becomes ready, or a power managed
mode is entered before the primary clock becomes
ready; the primary clock is then shut down.
3.5.3 EXIT BY WDT TIME-OUT
A WDT time -out will caus e diffe rent action s, dependin g
on which power managed mode the device is in when
the time-out occurs.
If the device is not executing code (all Idle modes and
Sleep mode), the time-out will result in a wake from the
power managed mode  (see Sections 3.2 through 3.4).
If the device is executing code (all Run modes), the
time-out will result in a WDT Reset (see Section 19.2
“Watchdog Timer (WDT)”). 
The WDT timer and postscaler are cleared by
executing a SLEEP or CLRWDT instru ction,  the loss  of a
currently selected clock source (if the Fail-Safe Clock
Monitor is enabled) and modifying the IRCF bits in the
OSCCON register if the internal oscillator block is the
system clock source.
3.5.4 EXIT WITHOUT AN OSCILLATOR 
START-UP DELAY
Certain exits from power managed modes do not
invoke the OST at all. These are:
• PRI_IDLE mode, where the primary clock source 
is not stopped; or
• the primary clock source is not any of LP, XT, HS 
or HSPLL modes.
In these cases, the primary clock source either does
not require an oscillator start-up delay, since it is
already running (PRI_IDLE), or normally does not
require an oscillator start-up delay (RC, EC and INTIO
Oscillator modes).
However, a fixed delay (appro xi ma tel y 10 μs) f ollowing
the wak e event is required when  leaving Sleep an d Idle
modes. This delay is required for the CPU to prepare
for execution. Instruction execution resumes on the first
clock cycle following this delay.
3.6 INTOSC Frequency Drift
The factory calibrates the internal oscillator block
output (INT OSC) for 8 MHz (see Tabl e 22-6). However ,
this frequency may drift as VDD or temperature
changes, which can affect the controller operation in a
variety of  ways.
It is possible to adjust the INTOSC frequency by
modifying the value in the OSCTUNE register
(Register 2-1). This has the side effect that the INTRC
clock source frequency is also affected. However, the
features that use the INTRC source often do not require
an exact frequency . These features include  the Fail-Safe
Clock Monitor, the Watchdog Timer and the RC_RUN/
RC_IDLE modes when the INTRC clock source is
selected.
Being able to adjust the INTOSC requires knowing
when an adjustment is required, in which direction it
should be made and in some cases, how large a
change is needed. Three examples follow but other
techniques may be used.

PIC18F1220/1320

3.6.1 EXAMPLE – EUSART

An adjustment may be indicated when the EUSART

begins to generate framing errors, or receives data with

errors while in Asynchronous mode. Framing errors

indicate that the system clock frequency is too high –

try decrem enting the valu e in the OSCTUNE reg ister to

reduce the system clock frequency. Errors in data may

suggest that the system clock speed is too low –

increm ent OSCTUNE.

3.6.2 EXAMPLE – TIMERS

This technique compares system clock speed to some

reference clock. Two timers may be used; one timer is

clocked by the peripheral clock, while the other is

clocked by a fixed reference source, such as the

Tim er1 oscillator.

Both timers are cleared, but the timer clocked by the

reference generates interrupts. When an interrupt

occurs, the internally clocked timer is read and both

timers are cleared. If the internally clocked timer value

is greater than expected, then the internal oscillator

block is running too fast – decrement OSCTUNE.

3.6.3 EXAMPLE – CCP IN CAPTURE

MODE

A CCP module can use free running Timer1 (or

Timer 3), cl oc ke d by th e int ernal oscilla tor bl ock and an

external event with a known period (i.e., AC power

frequenc y). The ti me of the first ev ent is c aptured in the

CCPRxH:CCPRxL registers and is recorded for use

later. When the second event causes a capture, the

time of the firs t eve nt is su btra cte d fro m the tim e of th e

second event. Since the period of the external event is

known, the time difference between events can be

calculated.

If the measured time is much greater than the

calculated time, the internal oscillator block is running

too fast – decrement OSCTUNE. If the measured time

is much less than the calculated time, the internal

oscillator block is running too slow – increment

OSCTUNE.

PIC18F1220/1320

NOTES:

PIC18F1220/1320

4.0 RESET

The PIC18F1220/1320 devices differentiate between

various kinds of Reset:

a) Power-on Reset (POR)

b) MCLR Reset during normal operation

c) MCLR Reset during Sleep

d) Watchdog Ti mer (WDT) Reset (during

execution)

e) Programmable Brown-out Reset (BOR)

f) RESET Inst ruction

g) Stack Full Reset

h) Stack Underflow Reset

Most registers are unaffected by a Reset. Their status

is unknown on POR and unchanged by all other

Resets. The other registers are forced to a “Reset

state”, depending on the type of Reset that occurred.

Most registers are not affected by a WDT wake-up,

since this is viewed as the resumption of normal

operation. Status bits from the RCON register

(Register 4-1), RI, TO, PD, POR and BOR, are set or

cleared differently in different Reset situations, as

indicated in Table 4-2. These bits are used in software

to determ in e t he nature of the Reset. See Table 4-3 for

a full description of the Reset states of all registers.

A simplif ied block diagra m of the On-Chip Rese t Circu it

is sh own i n Figure 4-1.

The Enhanced MCU devices have a MCLR noise filter

in the MCLR Reset path. The filter will detect and

ignore small pulses.

The MC LR pin is not driven low by any internal Resets,

inc luding the WDT.

The MCLR input provided by the MCLR pin can be

disabled with the MCLRE bit in Configuration

Regi ster 3H (CONFIG3H< 7>).

FIGURE 4-1: SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT

External Reset

MCLR

VDD

OSC1

WDT

Time-out

VDD Rise

Detect

OST/PWRT

INTRC

(1)

POR Pulse

OST

10-bit Ripple Counter

PWRT

Chip_Reset

11-bit Ripple Counter

Enable OST(2)

Enable PWRT

Note 1: This is a separate oscillator from the RC oscillator of the CLKI pin.

2: See Table 4-1 for time-out situations.

Brown-out

Reset BOR

RESET

Instruction

Stack

Pointer Stack Full/Underflow Reset

Sleep

( )_IDLE

1024 Cycles

65.5 ms

32 μs

MCLRE

PIC18F1220/1320
DS39605D-page 34 © 2006 Microchip Technology Inc.
4.1 Power-on Reset (POR)
A Power-on Reset pulse is generated on-chip when
VDD rise is detected. To take advantage of the POR
circuitry, just tie the MCLR pin through a resistor (1k to
10 kΩ) to VDD. This will eliminate external RC compo-
nents usually needed to create a Power-on Reset
delay. A minimum rise rate for VDD is specified
(param eter D004) . For a  slow rise t ime, see  Figure 4-2.
When the device start s  normal  operation (i.e ., ex its the
Reset condition), device operating parameters (volt-
age, frequency, temperature, etc.) must be met to
ensure operation. If these conditions are not met, the
device must be held in Reset until the operating
conditions are met.
FIGURE 4-2: EXTERN AL POWER-ON 
RESET CIRCUIT (FOR 
SLOW VDD POWER-UP)        
4.2 Power-up Timer (PWRT)
The Power-up T imer (PWRT) of the PIC18F1220/1320 is
an 11-bit counter, which uses the INTRC source as the
clock input. This yields a count of 2048 x 32 μs=65.6ms.
While the PWRT is counting, the device is held in Reset.
The power-up time  delay will vary from chip-to-chip due
to VDD, temperature and process variation. See DC
parameter 33 for details.
The PWRT is enabled by clearing configuration bit,
PWRTEN.
4.3 Oscillator Start-up Timer (OST)
The Oscillator Start-up Timer (OST) provides a 1024
oscillator cycle (from OSC1 input) delay after the
PWRT delay is over (parameter 33). This ensures that
the crystal oscillator or resonator has started and
stabilized.
The OST time-out is invoked only for XT, LP, HS and
HSPLL modes and only on Power-on Reset, or on exit
from most low-power modes.
4.4 PLL Lock Time -out
With the PLL enabled in its PLL mode, the time-out
sequence following a Power-on Reset is slightly
different from other oscillator modes. A portion of the
Power-up Timer is used to provi de a fix ed time-ou t that
is suf ficie nt for t he PLL to l ock to the  main  oscillator f re-
quency. This PLL lock time-out (TPLL) is typically 2 ms
and follows the Oscillator Start-up Time-out.
4.5 Brown-out Reset (BOR)
A configuration bit, BOR, can disable (if clear/
programmed), or enable (if set) the Brown-out Reset
circuitry. If VDD falls below VBOR (parameter D005) for
greate r than TBOR (p arameter 35) , the brown-o ut situa-
tion will reset the chip. A Reset may not occur if VDD
falls below VBOR for less than TBOR. The chip will
remain in Brown-out Reset until VDD rises above  VBOR.
If the Powe r-up T imer is enabled, i t will be invo ked after
VDD rises above VBOR; it then will keep the chip in
Reset for an additional time delay, TPWRT
(parameter 33). If VDD drops below VBOR while the
Power-up Timer is running, the chip will go back into a
Brown-ou t Reset and  the Power-up  T imer will  be initia l-
ized. Once VDD rises abov e VBOR, the Power-up T imer
will execute the additional time delay. Enabling BOR
Reset does not automatically enable the PWRT.
4.6 Time-out Sequence
On power-up, the time-out sequence is as follows:
First, afte r t he POR  pul se  has cle are d, PWRT time-o ut
is inv oked (if e nabled). Th en, the OS T is activa ted. The
tot al time-o ut wi ll var y base d on o scill ator co nfi guratio n
and the st atus of the PWRT. For exam pl e, in R C mod e
with the PWR T disabled , there wi ll be no time-out at all.
Figure 4-3, Figure 4-4, Figure 4-5, Figure 4-6 and
Figure 4-7 depict time-out sequences on power-up.
Since the time-outs occur from the POR pulse, if MCLR
is kept  low  long e nough,  all ti me-outs wi ll exp ire. Brin g-
ing MCLR high will begin execution immediately
(Figure 4-5). This is useful for testing purposes or to
synchronize more than one PIC18FXXXX device
operating in parallel.
Table 4-2 s hows the Re set condi tions for so me Specia l
Function Registers, while Table 4-3 shows the Reset
conditions for all the registers. 
Note 1: External Power-on Reset circuit is required
only if the VDD power-up slope is too slow.
The diode D helps discharge the capacitor
quickly when VDD powers down.
2: R < 40 kΩ is recommended to make sure that
the voltage drop across R does not violate
the device’s electrical specification.
3: R1 ≥ 1 kΩ will limit any current flowing into
MCLR from external capacitor C, in t he event
of MCLR/VPP pin breakdown due t o Electro-
static Discharge (ESD) or Electrical
Overstress (EOS).
C
R1
R
D
VDD
MCLR
PIC18FXXXX
VDD

PIC18F1220/1320

TABLE 4-1: TIME-OUT IN VARIOUS SITUATIONS

TABLE 4-2: STATUS BITS, THEIR SIGNIFICANCE AND THE INITIALIZATION CONDITION FOR

RCON REGISTER

Oscillator

Configuration

Power-up(2) and Brown-out Exit from

Low-Power Mode

PWRTEN = 0PWRTEN = 1

HSPLL 66 ms(1) + 1024 TOSC + 2 ms(2) 10 24 TOSC + 2 ms(2) 1024 TOSC + 2 ms (2)

HS, XT, LP 66 ms(1) + 1024 TOSC 1024 TOSC 1024 TOSC

EC, ECIO 66 ms(1) 5-10 μs(3) 5-10 μs(3)

RC, RCIO 66 ms(1) 5-10 μs(3) 5-10 μs(3)

INTIO1, INTIO2 66 ms(1) 5-10 μs(3) 5-10 μs(3)

Note 1: 66 ms (65.5 ms) is the nominal Power-up Timer (PWRT) delay.

2: 2 ms is the nominal time requi red for the 4x PLL to lock.

3: The program memory bias start-up time is always invoked on POR, wake-up from Sleep, or on any exit

from power managed mode that disables the CPU and instruction execution.

R/W-0 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1

IPEN ——RITO PD POR BOR

bit 7 bit 0

Note: Refer to Section 5.14 “RCON Re gister” for bit definit io ns.

Condition Program

Counter RCON

Power-on Reset 0000h 0--1 1100 1 1 1 0 0 0 0

RESET Inst ruction 0000h 0--0 uuuu 0 u u u u u u

Brown-out 0000h 0--1 11u- 1 1 1 u 0 u u

MCLR during Power Managed

Run modes 0000h 0--u 1uuu u 1 u u u u u

MCLR during Power Managed

Idle modes and Sleep 0000h 0--u 10uu u 1 0 u u u u

WDT Time-out during Full

Power or Power Managed Run 0000h 0--u 0uuu u 0 u u u u u

MCLR during Full Power

Execution 0000h 0--u uuuu u u u u u

Stack Full Reset (STVR = 1)1u

Stack Underflow Reset

(STVR = 1)u1

Stack Underflow Error (not an

actual Reset, STVR = 0)0000h u--u uuuu u u u u u u 1

WDT Time-out during Power

Managed Idle or Sleep PC + 2 u--u 00uu u 0 0 u u u u

Interrupt Exit from Power

Managed modes PC + 2 u--u u0uu u u 0 u u u u

Legend: u = unchanged, x = unknown, – = unimplemented bit, read as ‘0’

Note 1: When the wake-up is due to an interrupt and the GIEH or GIEL bits are set, the PC is loaded with the

inter rupt ve cto r (0x00 000 8h or 0x00 001 8h ).

PIC18F1220/1320

TABLE 4-3: INITIALIZATION CONDITIONS FOR ALL REGISTERS

Devices Power-on Rese t,

Brown-out Reset

MCLR Resets

WDT Reset

RESET Instruction

Stack Resets

Wake-up via WDT

or Interrupt

TOSU 1220 1320 ---0 0000 ---0 0000 ---0 uuuu(3)

TOSH 1220 1320 0000 0000 0000 0000 uuuu uuuu(3)

TOSL 1220 1320 0000 0000 0000 0000 uuuu uuuu(3)

STKPTR 1220 1320 00-0 0000 00-0 0000 uu-u uuuu(3)

PCLATU 1220 1320 ---0 0000 ---0 0000 ---u uuuu

PCLATH 1220 1320 0000 0000 0000 0000 uuuu uuuu

PCL 1220 1320 0000 0000 0000 0000 PC + 2(2)

TBLPTRU 1220 1320 --00 0000 --00 0000 --uu uuuu

TBLPTRH 1220 1320 0000 0000 0000 0000 uuuu uuuu

TBLPTRL 1220 1320 0000 0000 0000 0000 uuuu uuuu

TABLAT 1220 1320 0000 0000 0000 0000 uuuu uuuu

PRODH 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

PRODL 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

INTCON 1220 1320 0000 000x 0000 000u uuuu uuuu(1)

INTCON2 1220 1320 1111 -1-1 1111 -1-1 uuuu -u-u(1)

INTCON3 1220 1320 11-0 0-00 11-0 0-00 uu-u u-uu(1)

INDF0 1220 1320 N/A N/A N/A

POSTINC0 1220 1320 N/A N/A N/A

POSTDEC0 1220 1320 N/A N/A N/A

PREINC0 1220 1320 N/A N/A N/A

PLUSW0 1220 1320 N/A N/A N/A

FSR0H 1220 1320 ---- 0000 ---- 0000 ---- uuuu

FSR0L 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

WREG 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

INDF1 1220 1320 N/A N/A N/A

POSTINC1 1220 1320 N/A N/A N/A

POSTDEC1 1220 1320 N/A N/A N/A

PREINC1 1220 1320 N/A N/A N/A

PLUSW1 1220 1320 N/A N/A N/A

FSR1H 1220 1320 ---- 0000 ---- 0000 ---- uuuu

FSR1L 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.

Shaded cell s ind ic ate co nditions do not apply for the desig nat ed dev ic e.

Note 1: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).

2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the

interrupt vector (0008h or 0018h).

3: When the w ake -up is due to a n in terru pt a nd the G IEL or G IEH b it i s set, the TO SU, TOSH and TOSL ar e

updated with the current value of the PC. The STKPTR is modified to point to the next location in the

hardware stack.

4: See Table 4-2 for Reset value for specific condition.

5: Bits 6 and 7 of PORTA, LATA and TRISA are enabled, depending on the Oscillator mode selected. When

not enabled as PORTA pins, they are disabled and read ‘0’.

6: Bit 5 of PORTA is enabled if MCLR is disabled.

PIC18F1220/1320

BSR 1220 1320 ---- 0000 ---- 0000 ---- uuuu

INDF2 1220 1320 N/A N/A N/A

POSTINC2 1220 1320 N/A N/A N/A

POSTDEC2 1220 1320 N/A N/A N/A

PREINC2 1220 1320 N/A N/A N/A

PLUSW2 1220 1320 N/A N/A N/A

FSR2H 1220 1320 ---- 0000 ---- 0000 ---- uuuu

FSR2L 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

STATUS 1220 1320 ---x xxxx ---u uuuu ---u uuuu

TMR0H 1220 1320 0000 0000 0000 0000 uuuu uuuu

TMR0L 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

T0CON 1220 1320 1111 1111 1111 1111 uuuu uuuu

OSCCON 1220 1320 0000 q000 0000 q000 uuuu qquu

LVDCON 1220 1320 --00 0101 --00 0101 --uu uuuu

WDTCON 1220 1320 ---- ---0 ---- ---0 ---- ---u

RCON(4) 1220 1320 0--1 11q0 0--q qquu u--u qquu

TMR1H 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

TMR1L 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

T1CON 1220 1320 0000 0000 u0uu uuuu uuuu uuuu

TMR2 1220 1320 0000 0000 0000 0000 uuuu uuuu

PR2 1220 1320 1111 1111 1111 1111 1111 1111

T2CON 1220 1320 -000 0000 -000 0000 -uuu uuuu

ADRESH 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

ADRESL 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

ADCON0 1220 1320 00-0 0000 00-0 0000 uu-u uuuu

ADCON1 1220 1320 -000 0000 -000 0000 -uuu uuuu

ADCON2 1220 1320 0-00 0000 0-00 0000 u-uu uuuu

CCPR1H 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

CCPR1L 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

CCP1CON 1220 1320 0000 0000 0000 0000 uuuu uuuu

PWM1CON 1220 1320 0000 0000 0000 0000 uuuu uuuu

ECCPAS 1220 1320 0000 0000 0000 0000 uuuu uuuu

TABLE 4-3: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)

Devices Power-on Rese t,

Brown-out Reset

MCLR Resets

WDT Reset

RESET Instruction

Stack Resets

Wake-up via WDT

or Interrupt

Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.

Shaded cell s ind ic ate co nditions do not apply for the desig nat ed dev ic e.

Note 1: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).

2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the

interrupt vector (0008h or 0018h).

3: When the w ake -up is due to a n in terru pt a nd the G IEL or G IEH b it i s set, the TO SU, TOSH and TOSL ar e

updated with the current value of the PC. The STKPTR is modified to point to the next location in the

hardware stack.

4: See Table 4-2 for Reset value for specific condition.

5: Bits 6 and 7 of PORTA, LATA and TRISA are enabled, depending on the Oscillator mode selected. When

not enabled as PORTA pins, they are disabled and read ‘0’.

6: Bit 5 of PORTA is enabled if MCLR is disabled.

PIC18F1220/1320

TMR3H 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

TMR3L 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

T3CON 1220 1320 0-00 0000 u-uu uuuu u-uu uuuu

SPBRGH 1220 1320 0000 0000 0000 0000 uuuu uuuu

SPBRG 1220 1320 0000 0000 0000 0000 uuuu uuuu

RCREG 1220 1320 0000 0000 0000 0000 uuuu uuuu

TXREG 1220 1320 0000 0000 0000 0000 uuuu uuuu

TXSTA 1220 1320 0000 0010 0000 0010 uuuu uuuu

RCSTA 1220 1320 0000 000x 0000 000x uuuu uuuu

BAUDCTL 1220 1320 -1-1 0-00 -1-1 0-00 -u-u u-uu

EEADR 1220 1320 0000 0000 0000 0000 uuuu uuuu

EEDATA 1220 1320 0000 0000 0000 0000 uuuu uuuu

EECON2 1220 1320 0000 0000 0000 0000 0000 0000

EECON1 1220 1320 xx-0 x000 uu-0 u000 uu-0 u000

IPR2 1220 1320 1--1 -11- 1--1 -11- u--u -uu-

PIR2 1220 1320 0--0 -00- 0--0 -00- u--u -uu-(1)

PIE2 1220 1320 0--0 -00- 0--0 -00- u--u -uu-

IPR1 1220 1320 -111 -111 -111 -111 -uuu -uuu

PIR1 1220 1320 -000 -000 -000 -000 -uuu -uuu(1)

PIE1 1220 1320 -000 -000 -000 -000 -uuu -uuu

OSCTUNE 1220 1320 --00 0000 --00 0000 --uu uuuu

TRISB 1220 1320 1111 1111 1111 1111 uuuu uuuu

TRISA(5) 1220 1320 11-1 1111(5) 11-1 1111(5) uu-u uuuu(5)

LATB 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

LATA(5) 1220 1320 xx-x xxxx(5) uu-u uuuu(5) uu-u uuuu(5)

PORTB 1220 1320 xxxx xxxx uuuu uuuu uuuu uuuu

PORTA(5,6) 1220 1320 xx0x 0000(5,6) uu0u 0000(5,6) uuuu uuuu(5,6)

TABLE 4-3: INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)

Devices Power-on Rese t,

Brown-out Reset

MCLR Resets

WDT Reset

RESET Instruction

Stack Resets

Wake-up via WDT

or Interrupt

Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition.

Shaded cell s ind ic ate co nditions do not apply for the desig nat ed dev ic e.

Note 1: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).

2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the

interrupt vector (0008h or 0018h).

3: When the w ake -up is due to a n in terru pt a nd the G IEL or G IEH b it i s set, the TO SU, TOSH and TOSL ar e

updated with the current value of the PC. The STKPTR is modified to point to the next location in the

hardware stack.

4: See Table 4-2 for Reset value for specific condition.

5: Bits 6 and 7 of PORTA, LATA and TRISA are enabled, depending on the Oscillator mode selected. When

not enabled as PORTA pins, they are disabled and read ‘0’.

6: Bit 5 of PORTA is enabled if MCLR is disabled.

PIC18F1220/1320

FIGURE 4-3: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD, VDD RISE < TPWRT)

FIGURE 4-4: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 1

FIGURE 4-5: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 2

TPWRT

TOST

VDD

MCLR

INTERNAL POR

PWRT TIME-OUT

OST TIME-OUT

INTERNAL RESET

TPWRT

TOST

VDD

MCLR

INTER N AL PO R

PWRT TIME-OUT

OST TIME-OUT

INTERNAL RESET

VDD

MCLR

INTERNAL POR

PWRT TIME-OUT

OST TIME-OUT

INTERNAL RESET

TPWRT

TOST

PIC18F1220/1320

FIGURE 4-6: SLOW RISE TIME (MCLR TIED TO VDD, VDD RISE > TPWRT)

FIGURE 4-7: TIME-OUT SEQUENCE ON POR W/PLL ENABLED (MCLR TIED TO VDD)

VDD

MCLR

INTERNAL POR

PWRT TIME-OUT

OST TIME-OUT

INTERNAL R ESET

0V 1V 5V

TPWRT

TOST

TPWRT

TOST

VDD

MCLR

INTERNAL POR

PWRT TIME-OUT

OST TIME-OUT

INTERNAL RESET

PLL TIME-OUT

TPLL

Note: TOST = 1024 clock cycles.

TPLL ≈ 2 ms max. First three stages of the PWRT timer.

PIC18F1220/1320

5.0 MEMORY ORGANIZATION

There are three memory types in Enhanced MCU

devices. Th ese memory types are:

• Program Memory

• Data RAM

• Data EEPROM

Data and program memory use separate busses,

which allows for concur rent access of thes e types.

Addition al detai led informat ion for Flas h program mem-

ory and data EEPROM is provided in Section 6.0

“Flash Program Memory” and Section 7.0 “Data

EEPROM Memory”, respec tiv el y.

FIGURE 5-1: PROGRAM MEMORY MAP

AND STACK FOR

PIC18F1220

5.1 Program Memory Organization

A 21-b it progr am count er is capab le of ad dressin g the

2-Mb yte prog ram m emo ry space. Ac ces s ing a l ocation

between the physically implemented memory and the

2-Mbyte address will cause a read of all ‘0’s (a NOP

instruction).

The PIC18F1220 has 4 Kbytes of Flash memory and

can store up to 2,048 single-word instructions.

The PIC18F1320 has 8 Kbytes of Flash memory and

can store up to 4,096 single-word instructions.

The Rese t vector addres s is at 0000h and the interru pt

vector addresses are at 0008h and 0018h.

The program memory maps for the PIC18F1220 and

PIC18F1320 devices are shown in Figure 5-1 and

Figure 5-2, respectively.

FIGURE 5-2: PROGRAM MEMORY MAP

AND STACK FOR

PIC18F1320

PC<20:0>

Stack Level 1

•

Stack Level 31

Reset Vector

Low Priority Interrupt Vector

•

CALL,RCALL,RETURN

RETFIE,RETLW

0000h

0018h

On-Chip

Program Memory

High Priority Interrupt Vector 0008h

User Memo ry Spa ce

1FFFFFh

1000h

0FFFh

Read ‘0’

200000h

PC<20:0>

Stack Level 1

•

Stack Level 31

Reset Vector

Low Priority Interrupt Vector

•

CALL,RCALL,RETURN

RETFIE,RETLW

0000h

0018h

2000h

1FFFh

On-Chip

Program Mem ory

High Priority Interrupt Vector 0008h

User Memo ry Space

Read ‘0’

1FFFFFh

200000h

PIC18F1220/1320

5.2 Return Address Stack

The return address s t ac k al low s any comb in atio n of up

to 31 program calls and interrupts to occur. The PC

(Program Counter) is pushed onto the stack when a

CALL or RCALL instruction is executed, or an interrupt

is Acknowledged. The PC value is pulled off the stack

on a RETURN, RETLW or a RETFIE instruction. PCLA TU

and PCLATH are not affected by any of the RETURN or

CALL instructi ons .

The stack operates as a 31-word by 21-bit RAM and a

5-bit stack pointer, with the Stack Pointer initialized to

00000B after all Resets. There is no RAM associated

with Stack Pointer, 00000B. This i s o nly a R e se t valu e.

During a CALL type instruction, causing a push onto the

stack, the Stack Pointer is first incremented and the

RAM location pointed to by the Stack Pointer

(STKPTR) registe r is written with the contents of the PC

(already pointing to th e instructio n following the CALL).

During a RETURN type instruction, causing a pop from

the stack, the contents of the RAM location pointed to

by the STKPTR are transferred to the PC and then the

Stack Pointer is decremented.

The stack space is not part of either program or data

space. The Stack Pointer is readable and writable and

the address on the top of the stack is readable and

writable through the top-of-stack Special File

Registers. Data can also be pushed to or popped from

the stack using the top-of-stack SFRs. Status bits

indicate if the stack is full, has overflowed or

underflowed.

5.2.1 TOP-OF-STACK ACCESS

The top of the stack is readable and writable. Three

contents of the stack location pointed to by the

STKPTR register (Figure 5-3). This allows users to

implement a software st a ck if ne ces s ary. After a CALL,

RCALL or interrupt, the software can read the pushed

value by reading the TOSU, TOSH and TOSL registers.

These v alues can b e placed on a u ser define d software

stack. At return time, the software can replace the

TOSU, TOSH and TOSL and do a return.

The user must disable the global interrupt enable bits

while accessing the stack to prevent inadvertent stack

corruption.

5.2.2 RETURN STACK POINTER

(STKPTR)

The STKP TR reg ister (Re giste r 5-1) co nta ins the st ack

pointer value, the STKFUL (Stack Full) status bit and

the STKUNF (Stack Underflow) status bits. The value

of the Stack Pointer can be 0 through 31. The Stack

Pointer increments before values are pushed onto the

stack and decrements after values are popped off the

stack. At Reset, the Stack Pointer value will be zero.

The user may read and write the Stack Pointer value.

This feature can be used by a Real-Time Operating

System for return stack maintenance.

After t he PC is pus hed on to the st ack 31 times (wi thout

popping any values off the stack), the STKFUL bit is

set. The STKFUL bit is cleared by software or by a

POR.

The action that takes place when the stack becomes

full depends on the state of the STVR (Stack Overflow

Reset Enabl e) configura tion bit. (Re fer to Section 19.1

“Configuration Bits” for a description of the device

configuration bits.) If STVR is set (default), the 31st

push wil l push the ( PC + 2) value o nto the st ack, set th e

STKFUL bit and reset the device. The STKFUL bit will

remain set and the Stack Pointer will be set to zero.

If STVR is cleared, the STKFUL bit will be set on the

31st push and the Stack Pointer will increment to 31.

Any additional pushes will not overwrite the 31st push

and STKPTR will remain at 31.

When the stack has been popped enough times to

unload th e stack, the ne xt pop will return a value of zero

to the PC and sets the STKUNF bit, while the Stack

Pointer remains at zero. The STKUNF bit will remain

set until cleared by software or a POR occurs.

FIGURE 5-3: RETURN ADDRESS STACK AND ASSOCIATED REGISTERS

Note: Returning a value of zero to the PC on an

underflow has the effect of vectoring the

program to the Reset vector, where the

stack conditions can be verified and

appropriate actions can be taken. This is

not the same as a Reset, as the contents

of the SFRs are not affected.

00011

001A34h

11111

11110

11101

00010

00001

00000

00010

Return Address Stack

Top-of-Stack 000D58h

TOSLTOSHTOSU 34h1Ah00h STKPTR<4:0>

PIC18F1220/1320

5.2.3 PUSH AND POP INSTRUCTIONS

Since the Top- of-Stack (T OS ) is rea dab le a nd w ritable,

the abili ty to push v alues onto the stac k and pull values

off t he st ack, wit hout distu rbing norm al program ex ecu-

tion, is a d esirable optio n. To push th e current PC value

onto the stack, a PUSH instruction can be executed.

This will increment the Stack Pointer and load the cur-

rent PC value onto the stack. TOSU, TOSH and TOSL

can then be modified to place data or a return address

on the stack.

The ability to pull the TOS value off of the stack and

replace it with the value that was previously pushed

onto the stack, without disturbing normal execution, is

achieved by using the POP inst ruction. T he POP instru c-

tion discards the current TOS by decrementing the

Stack Pointer. The previous value pushed onto the

stack then becomes the TOS value.

5.2.4 ST ACK FULL/UNDERFLOW RESETS

These Resets are enabled by programming the STVR

bit in Configuration Register 4L. When the STVR bit is

cleared , a ful l or u nderflow co ndi tio n will set the app ro-

priate STKFUL or STKUNF bit, but not cause a device

Reset. When the STVR bit is set, a full or underflow

condition will set the appropriate STKFUL or STKUNF

bit and then cause a device Reset. The STKFUL or

STKUNF bits are cleared by the user software or a

Power-on Reset.

R/C-0 R/C-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

STKFUL STKUNF — SP4 SP3 SP2 SP1 SP0

bit 7 bit 0

bit 7(1) STKFUL: Stack Full Flag bit

1 = Stack became full or overflowed

0 = Stack has not become full or overflowed

bit 6(1) STKUNF: Stack Underflow Flag bit

1 = Stack underflow occurred

0 = Stack underflow did not occur

bit 5 Unimplemented: Read as ‘0’

bit 4-0 SP4:SP0: Stack Pointer Location bits

Note 1: Bit 7 and bi t 6 are cleared by user software or by a POR.

Legend:

R = Readable bit W = Writable bit U = Unimplemented C = Clearable only bit

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

5.3 Fast Register St ack

A “fast return” option is available for interrupts. A fast

BSR regist ers and is only one in depth. The sta ck is not

readable or writable and is loaded with the current

value o f the correspo nding registe r when the pro cessor

vectors for an interrupt. The values in the registers are

then loaded back into the working registers, if the

RETFIE, FAST instruction is used to return from the

interrupt.

All interrupt sources will push values into the stack

registers. If both low and high priority interrupts are

enabled, the stack registers cannot be used reliably to

return from lo w priority interrupt s. If a high pri ority inter-

rupt occurs while servicing a low priority interrupt, the

stac k reg is ter v al ues s tor ed by the l ow p r iori ty in terru pt

will be overwritten. Users must save the key registers

in software during a low priority interrupt.

If interrupt pri ority is not used, all interrupts may use the

fast register stack for returns from interrupt.

If no interrupts are used, the fast register stack can be

used to rest ore the S tatus, WREG and BSR register s at

the end of a subroutine call. To use the fast register

stack for a subroutine call, a CALL LABEL, FAST

instruction must be executed to save the Status,

WREG and BSR registers to the fast register stack. A

RETURN, FAST instruction is then ex ec uted to restore

these registers from the fast register stack.

Example 5-1 shows a source code example that uses

the fast register stack during a subroutine call and

return.

EXAMPLE 5-1: FAST REGISTER STACK

CODE EXAMPLE

5.4 PCL, PCLATH and PCLATU

The Program Counter (PC) spec ifies the addres s of the

instruction to fetch for execution. The PC is 21-bits

wide. The low byte, known as the PCL register, is both

readable and writable. The high byte, or PCH register,

cont ains th e PC<15 :8> bit s and is not direc tly read able

or writable. Updates to the PCH register may be per-

formed th rough the PCLATH regis ter . The upper by te is

called PCU. This register contains the PC<20:16> bits

and is not directly readable or writable. Updates to the

PCU register may be performed through the PCLATU

The contents of PCLATH and PCLATU will be

transferred to the program counter by any operation

that writes PCL. Similarly, the upper two bytes of the

program counter will be transferred to PCLATH and

PCLATU by an operation that reads PCL. This is useful

for computed offsets to the PC (see Section 5.8.1

“Compu ted GOTO”).

The PC addresses bytes in the program memory. To

prevent the PC from becoming misaligned with word

instructions, the LSB of PCL is fixed to a value of ‘0’.

The PC increments by 2 to address sequential

instruc t ion s in the prog ram memo ry.

The CALL, RCALL, GOTO and program branch instruc-

tions write to the program counter directly. For these

instruc tion s, the content s of PC LATH an d PCLATU are

not transferred to the program counter.

CALL SUB1, FAST ;STATUS, WREG, BSR

;SAVED IN FAST REGISTER

;STACK

•

SUB1 •

•

RETURN, FAST ;RESTORE VALUES SAVED

;IN FAST REGISTER STACK

PIC18F1220/1320

5.5 Clocking Scheme/Instruction

Cycle

The clock input (from OSC1) is internally divided by

four to generate four non-overlapping quadrature

clocks, namely Q1, Q2, Q3 and Q4. Internally, the

Program Counter (PC) is incremented every Q1, the

instruction is fetched from the program memory and

latched into the instruction register in Q4. The instruc-

tion is decoded and executed during the following Q1

through Q4. The clocks and instruction execution flow

are shown in Figure 5-4.

5.6 Instruction Flow/Pipelining

An “Instruction Cycle” consists of four Q cycles (Q1,

Q2, Q3 and Q 4). The instructio n fe tch and ex ecu te a r e

pipelined such that fetch takes one instruction cycle,

while decode and execute takes another instruction

cycle. However, due to the pipelining, each instruction

effectively executes in one cycle. If an instruction

causes the program counter to change (e.g., GOTO),

then tw o cycles are req uired to com plete the ins truction

(Example 5-2).

A fetch cycle begins with the Program Counter (PC)

incrementing in Q1.

In the ex ecution cycle , the fetched instruction i s latched

into the “Instruction Register” (IR) in cycle Q1. This

instruction is then decoded and executed during the

Q2, Q 3 and Q4 c ycles. Data mem ory is read during Q2

(operand read) and written during Q4 (destination

write).

FIGURE 5-4: CLOCK/INSTRUCTION CYCLE

EXAMPLE 5-2: INSTRUCTION PIPELINE FLOW

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

OSC1

OSC2/CLKO

(RC Mode)

PC PC + 2 PC + 4

Fetch INST (PC)

Execute IN ST (P C – 2)

Fetch IN ST (PC + 2)

Execute IN ST (PC)

Fetch INST (PC + 4)

Execute IN ST (PC + 2)

Internal

Phase

Clock

All instructions are single cycle, except for any program branches. These take two cycles, since the fetch instruction

is “flushed” from the pipeline, while the new instruction is being fetched and then executed.

TCY0TCY1TCY2TCY3TCY4TCY5

1. MOVLW 55h Fetch 1 Execute 1

2. MOVWF PORTB Fetch 2 Execute 2

3. BRA SUB_1 Fetch 3 Execute 3

4. BSF PORTA, BIT3 (Forced NOP) Fetch 4 Flush (NOP)

5. Instruction @ address SUB_1 Fetch SUB_1 Execute SUB_1

PIC18F1220/1320
DS39605D-page 46 © 2006 Microchip Technology Inc.
5.7 Instructi ons in Program Memory
The program memory is addressed in bytes. Instruc-
tions are stored as two bytes or four bytes in program
memory. The Least Significant Byte of an instruction
word is always stored in a program memory location
with an even address (LSB = 0). Figure 5-5 shows an
exampl e of how instruc tion word s are stored i n the pro-
gram memory. To maintain alignment with instruction
boundaries, the PC increments in steps of 2 and the
LSB will always read ‘0’ (see Section 5.4 “PCL,
PCLATH and PCLATU”).
The CALL and GOTO instructions have the absolute
program memory address embedded into the instruc-
tion. Since instructions are always stored on word
boundaries, the data contained in the instruction is a
word address. The word address is written to
PC<20:1 >, which  accesses  the des ired byte  address i n
program memory. Instruction #2 in Figure 5-5 shows
how the instruction ‘GOTO 000006h’ is enc ode d in th e
program memory. Program branch instructions, which
encode a relative address offset, operate in the same
manner. The of fs et v alu e s tore d in a  br an ch  ins truc tio n
represents the number of single-word instructions that
the PC wi ll be  off set by. Section 20.0 “I nstruction  Set
Summary” provides further details of the instruction
set.
FIGURE 5-5: INS TRUCTIONS IN PROGRAM MEMORY
5.7.1 TW O-WORD INSTRUCTIONS
PIC18F1220/1320 devices have four two-word
instructions: MOVFF,  CALL,  GOTO a nd LFSR. The second
word of thes e instructions has the 4  MSBs set to ‘1’s and
is decoded as a NOP instruction. The  lower 12 bit s of  the
second word contain data to be used by the instruction.
If the first word of the instruction is executed, the data in
the second word is accessed. If the second word of the
instruction is exe cuted by it sel f (first word was skipped),
it will execute as a NOP. This action is necessary when
the two-word instruction is preceded by a conditional
instruction that results in a skip operation. A program
example that demonstrates this concept is shown in
Example 5-3. Refer to Section 20.0 “Instruction Set
Summary” for further details of the instruction  set.
EXAMPLE 5-3: TWO-WORD INSTRUCTIONS
Word Address
LSB = 1LSB = 0↓
Program Memory
Byte Locations  →        000000h
000002h
000004h
000006h
Instruction 1: MOVLW 055h 0Fh 55h 000008h
Instruction 2: GOTO 000006h EFh 03h 00000Ah
F0h 00h 00000Ch
Instruction 3: MOVFF 123h, 456h C1h 23h 00000Eh
F4h 56h 000010h
000012h
000014h
CASE 1:
Object Code Source Code
0110 0110 0000 0000 TSTFSZ REG1 ; is RAM location 0?
1100 0001 0010 0011 MOVFF REG1, REG2 ; No, skip this word
1111 0100 0101 0110 ; Execute this word as a NOP
0010 0100 0000 0000 ADDWF REG3 ; continue code
CASE 2:
Object Code Source Code
0110 0110 0000 0000 TSTFSZ REG1 ; is RAM location 0?
1100 0001 0010 0011 MOVFF REG1, REG2 ; Yes, execute this word
1111 0100 0101 0110 ; 2nd word of instruction
0010 0100 0000 0000 ADDWF REG3 ; continue code

PIC18F1220/1320

5.8 Look-up Tables

Look-up tables are implemented two ways:

• Computed GOTO

• Table Reads

5.8.1 COMPUTED GOTO

A comput ed GOTO is a ccom pli shed by addi ng a n offset

to the program counter (see Example 5-4).

A look-up table can be formed with an ADDWF PCL

instruction and a group of RETLW 0xnn instructions.

WREG is loaded with an offset into the table before

execut ing a c al l to tha t table. Th e fi rst instructi on of th e

called routine is the ADDWF PCL instruction. The next

instruction executed will be one of the RETLW 0xnn

instructions, that returns the value 0xnn to the calling

function.

The offset value (in WREG) specifies the number of

bytes that the program counter should advance and

should be multiples of 2 (LSB = 0).

In this method, only one data byte may be stored in

each instruction location and room on the return

address stack is required.

EXAMPLE 5-4: COMPUTED GOTO USING

AN OFFSET VALUE

5.8.2 TABLE READS/TABLE WRITES

A better method of storing data in program memory

allow s two bytes of dat a to be stored in each instruc tion

location.

Look-up table data may be stored two bytes per pro-

gram word by using table reads and writes. The Table

Pointer (TBLPTR) register specifies the byte address

and the Table Latch (TABLAT) register contains the

data that is read from or written to program memory.

Data is transferred to/from program memory, one byte

at a time.

The table read/table write operation is discussed

further in Section 6.1 “Table Reads and Table

Writes”.

5.9 Data Memory Organization

The data memory is im ple me nte d as static RAM . Eac h

allowing up to 4096 bytes of data memory. Figure 5-6

shows the data memory organization for the

PIC18F1220/1320 devices.

The data memory map is divided into as many as

16 banks that contain 256 bytes eac h. The lowe r 4 bits

of the Bank Select Register (BSR<3:0>) select which

bank w ill be acce ssed. The upper 4 bit s for the BSR are

not implemented.

The data memory contains Special Function Registers

(SFR) and General Purpose Registers (GPR). The

SFRs are used for control and status of the controller

and periph eral function s, while GPRs ar e used for dat a

storage and scratch pad operations in the user’s appli-

cation. The SFRs start at the last location of Bank 15

(FFFh) and extend towa rds F80h. Any remaining sp ace

beyond the SFRs in the Bank may be implemented as

GPRs. GPRs start at the first location of Bank 0 and

grow up w ards . An y re ad of a n un im ple me nte d l ocation

will read as ‘0’s.

The entire data memory may be accessed directly or

indirec tly. Dir ect add ress in g m ay re qui re th e us e of the

BSR register. Indirect addressing requires the use of a

File Select Register (FSRn) and a corresponding Indi-

rect File Operand (INDFn). Each FSR holds a 12-bit

address value that can be used to access any location

in the Data Memory map without banking. See

Section 5.12 “Indirect Addressing, INDF and FSR

Registers” for indirect addressing details.

The instruction set and architecture allow operations

across all banks . This may be acc omplished by indirec t

address ing or by the us e of th e MOVFF instruction. The

MOVFF instruction is a two-word/two-cycle instruction

that moves a value from one register to another.

To ensure that commonly used registers (SFRs and

select GPRs) can be accessed in a single cycle,

regardless of the current BSR values, an Access Bank

is imp lemented. A segm ent of Bank 0 and a segment of

Bank 15 comprise the Access RAM. Section 5.10

“Access Bank” provides a detailed description of the

Access RAM.

5.9.1 GENERAL PURPOSE

Enhanced MCU devices may have banked memory in

the GPR area. GPRs are not initialized by a Power-on

Reset and are unchanged on all other Resets.

Data RAM is available for use as GPR registers by all

instructions. The second half of Bank 15 (F80h to

FFFh) contains SFRs. All other banks of data memory

contain GPRs, starting with Bank 0.

MOVFW OFFSET

CALL TABLE

ORG 0xnn00

TABLE ADDWF PCL

RETLW 0xnn

PIC18F1220/1320

FIGURE 5-6: DATA MEMORY MAP FOR PIC18F1220/1320 DEVICES

Bank 0

Bank 14

Bank 15

Data Me mo r y Map

BSR<3:0>

= 0000

= 1111

080h

07Fh

F80h

FFFh

00h

7Fh

80h

FFh

Access Bank

When a = 0,

The BSR is ignored and the

Access Bank is used.

The first 128 bytes are

General Purpose RAM

(from Bank 0).

The second 128 bytes are

Special Function Registers

(from Bank 15).

When a = 1,

The B SR spe ci fie s th e Ba nk

used by the inst ruct ion.

F7Fh

F00h

EFFh

0FFh

000h

Access RAM

FFh

00h

FFh

00h

GPR

SFR

Unused

Access RAM High

Access RAM Low

Bank 1

to Unused

Read ‘00h’

= 1110

= 0001 (SFRs)

PIC18F1220/1320

5.9.2 SPECIAL FUNCTION REGISTERS

The Special Function Registers (SFRs) are registers

used by the CPU and peripheral modules for controlling

the desired operation of the device. These registers are

implemented as static RAM. A list of these registers is

given in Table 5-1 and Table 5-2.

The SFRs can be classified into two sets: those asso-

ciated with the “core” function and those related to the

peripheral functions. Those registers related to the

“core” are descri bed i n t his s ection, while those rel ate d

to the operation of the peripheral features are

describ ed in the se cti on of that peri pheral feature.

The SFRs are typically distributed among the peripherals

whose functions they control.

The unused SFR locations will be unimplemented and

read as ‘0’s.

TABLE 5-1: SPECIAL FUNCTION REGISTER MAP FOR PIC18F1220/1320 DEVICES

Address Name Address Name Address Name Address Name

FFFh TOSU FDFh INDF2(2) FBFh CCPR1H F9Fh IPR1

FFEh TOSH FDEh POSTINC2(2) FBEh CCPR1L F9Eh PIR1

FFDh TOSL FDDh POSTDEC2(2) FBDh CCP1CON F9Dh PIE1

FFCh STKPTR FDCh PREINC2(2) FBCh — F9Ch —

FFBh PCLATU FDBh PLUSW2(2) FBBh — F9Bh OSCTUNE

FFAh PCLATH FDAh FSR2H FBAh — F9Ah —

FF9h PCL FD9h FSR2L FB9h — F99h —

FF8h TBLPTRU FD8h STATUS FB8h — F98h —

FF7h TBLPTRH FD7h TMR0H FB7h PWM1CON F97h —

FF6h TBLPTRL FD6h TMR0L FB6h ECCPAS F96h —

FF5h TABLAT FD5h T0CON FB5h — F95h —

FF4h PRODH FD4h — FB4h — F94h —

FF3h PRODL FD3h OSCCON FB3h TMR3H F93h TRISB

FF2h INTCON FD2h LVDCON FB2h TMR3L F92h TRISA

FF1h INTCON2 FD1h WDTCON FB1h T3CON F91h —

FF0h INTCON3 FD0h RCON FB0h SPBRGH F90h —

FEFh INDF0(2) FCFh TMR1H FAFh SPBRG F8Fh —

FEEh POSTINC0(2) FCEh TMR1L FAEh RCREG F8Eh —

FEDh POSTDEC0(2) FCDh T1CON FADh TXREG F8Dh —

FECh PREINC0(2) FCCh TMR2 FACh TXSTA F8Ch —

FEBh PLUSW0(2) FCBh PR2 FABh RCSTA F8Bh —

FEAh FSR0H FCAh T2CON FAAh BAUDCTL F8Ah LATB

FE9h FSR0L FC9h — FA9h EEADR F89h LATA

FE8h WREG FC8h — FA8h EEDATA F88h —

FE7h INDF1(2) FC7h — FA7h EECON2 F87h —

FE6h POSTINC1(2) FC6h — FA6h EECON1 F86h —

FE5h POSTDEC1(2) FC5h — FA5h — F85h —

FE4h PREINC1(2) FC4h ADRESH FA4h — F84h —

FE3h PLUSW1(2) FC3h ADRESL FA3h — F83h —

FE2h FSR1H FC2h ADCON0 FA2h IPR2 F82h —

FE1h FSR1L FC1h ADCON1 FA1h PIR2 F81h PORTB

FE0h BSR FC0h ADCON2 FA0h PIE2 F80h PORTA

Note 1: Unimplement ed registers are read as ‘0’.

2: This is not a physical register.

PIC18F1220/1320
DS39605D-page 50 © 2006 Microchip Technology Inc.
TABLE 5-2: REGISTER FILE SUMMARY (PIC18F1220/1320)
File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR Details on 
page:
TOSU — — — Top-of-Stack Upper Byte (TOS<20:16>) ---0 0000 36, 42
TO SH Top-of-Stack High Byte (TOS<15:8>) 0000 0000 36, 42
TOSL Top-of-Stack Low Byte (TOS<7:0>) 0000 0000 36, 42
STKPTR STKFUL STKUNF — Return S tack Pointer 00-0 0000 36, 43
PCLATU ——bit 21
(3) Holding Register for PC<20:16> ---0 0000 36, 44
PCLATH Holding Regi st er for  PC<15: 8> 0000 0000 36, 44
PCL PC Low Byte (PC<7:0>) 0000 0000 36, 44
TBLPTRU —— bit 21 Program Memory Table Pointer Upper Byte (TBLPTR<20:16>) --00 0000 36, 60
TBLPTRH Program Memory Table P ointe r High Byte (TBLPTR<15:8>) 0000 0000 36, 60
TBLPTRL Program Memory Table Pointer Low Byte (TBLPTR<7:0>) 0000 0000 36, 60
TABLAT Program Memory  Table Latch 0000 0000 36, 60
PRODH Product Register High Byte xxxx xxxx 36, 71
PRODL Product Register Low Byte xxxx xxxx 36, 71
INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 36, 75
INTCON2 RBPU INTEDG0 INTEDG1 INTEDG2 —TMR0IP—RBIP1111 -1-1 36, 76
INTCON3 INT2IP INT1IP —INT2IEINT1IE— INT2IF INT1IF 11-0 0-00 36, 77
INDF0 Uses contents of FSR0 to address data memory – value of FSR0 not changed (not a physical register) N/A 36, 53
POSTINC0 Uses contents of FSR0 to address data memory – value of FSR0 post-incremented (not a physical register) N/A 36, 53
POSTDEC0 Uses contents of FSR0 to address data memory– value of FSR0 post-decremented (not a physical register) N/A 36, 53
PREINC0 Uses contents of FSR0 to address data memory – value of FSR0 pre-incremented (not a physical register) N/A 36, 53
PLUSW0 Uses contents of FS R0 to address data memor y – value of FSR0 offset by W (not a physical register) N/A 36, 53
FSR0H — — — — Indirect Data Memory Address Pointer 0 High ---- 0000 36, 53
FSR0L Indirect Data Memory Address Pointer 0 Low Byte xxxx xxxx 36, 53
WREG Worki ng Regi s ter xxxx xxxx 36
INDF1 Uses contents of FSR1 to address data memory – value of FSR1 not changed (not a physical register) N/A 36, 53
POSTINC1 Uses contents of FSR1 to address data memory – value of FSR1 post-incremented (not a  physical register) N/A 36, 53
POSTDEC1 Uses contents of FSR1 to address data memory – value of FSR1 post-decremented (not a physical register) N/A 36, 53
PREINC1 Uses contents of FSR1 to address data memory – value of FSR1 pre-incremented (not a physical register) N/A 36, 53
PLUSW1 Uses contents of FS R1 to address data memor y – value of FSR1 offset by W (not a physical register) N/A 36, 53
FSR1H — — — — Indirect Data Memory Address Pointer 1 High ---- 0000 36, 53
FSR1L Indirect Data Memory Address Pointer 1 Low Byte xxxx xxxx 36, 53
BSR — — — — Bank Select Register ---- 0000 37, 52
INDF2 Uses contents of FSR2 to address data memory – value of FSR2 not changed (not a physical register) N/A 37, 53
POSTINC2 Uses contents of FSR2 to address data memory – value of FSR2 post-incremented (not a  physical register) N/A 37, 53
POSTDEC2 Uses contents of FSR2 to address data memory – value of FSR2 post-decremented (not a physical register) N/A 37, 53
PREINC2 Uses contents of FSR2 to address data memory – value of FSR2 pre-incremented (not a physical register) N/A 37, 53
PLUSW2 Uses contents of FS R2 to address data memor y – value of FSR2 offset by W (not a physical register)  N/A 37, 53
FSR2H — — — — Indirect Data Memory Address Pointer 2 High ---- 0000 37, 53
FSR2L Indirect Data Memory Address Pointer 2 Low Byte xxxx xxxx 37, 53
STATUS — — —NOVZDCC---x xxxx 37, 55
TMR0H Timer0 Register High Byte 0000 0000 37, 101
TMR0L Timer0 Register Low Byte xxxx xxxx 37, 101
T0CON TMR0ON T08BIT T0CS T0SE PSA T0PS2 T0PS1 T0PS0 1111 1111 37, 99
OSCCON IDLEN IRCF2 IRCF1 IRCF0 OSTS IOFS SCS1 SCS0 0000 q000 37, 17
LVDCON —— IVRST LVDEN LVDL3 LVDL2 LVDL1 LVDL0 --00 0101 37, 167
WDTCON — — — — — — —SWDTEN--- ---0 37, 180
RCON IPEN ——RITO PD POR BOR 0--1 11q0 35, 56, 84
Legend: x = unknow n , u = unchanged, – = unimpl emented, q = value depends on condition
Note 1: RA6 and associated bits are configured as port pins in RCIO, ECIO and INTIO2 (with port function on RA6) Oscillator mode only and read ‘0’ 
in all other oscillator modes.
2: RA7 and associated bits are configured as port pins in INTIO2 Oscillator mode only and read ‘0’ in all other modes.
3: Bit 21 of the PC is only available in Test mode and Serial Programming modes.
4: The RA5 port bit is only available when MCLRE fuse (CONFIG3H<7>) is programmed to ‘0’. Otherwise, RA5 reads ‘0’. This bit is read-only.

© 2006 Microchip Technology Inc. DS39605D-page 51
PIC18F1220/1320
TMR1H Timer1 Register High Byte xxxx xxxx 37, 108
TMR1L Timer1 Register Low Byte xxxx xxxx 37, 108
T1CON RD16 T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON 0000 0000 37, 103
TMR2 Timer2 Register 0000 0000 37, 109
PR2 Timer2 Period Register 1111 1111 37, 109
T2CON — TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 37, 109
ADRESH A/D Result Register High Byte xxxx xxxx 37, 164
ADRESL A/D Result Register Low Byte xxxx xxxx 37, 164
ADCON0 VCFG1 VCFG0 — CHS2 CHS1 CHS0 GO/DONE ADON 00-0 0000 37, 155
ADCON1 — PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 -000 0000 37, 156
ADCON2 ADFM — ACQT2 ACQT1 ACQT0 ADCS2 ADCS1 ADCS0 0-00 0000 37, 157
CCPR1H Capture/Compare/PWM Register 1 High Byte xxxx xxxx 37. 116
CCPR1L Capture/Compare/PWM Register 1 Low Byte xxxx xxxx 37, 116
CCP1CON P1M1 P1M0 DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 0000 0000 37, 115
PWM1CON PRSEN PDC6 PDC5 PDC4 PDC3 PDC2 PDC1 PDC0 0000 0000 37, 126
ECCPAS ECCPASE ECCPAS2 ECCPAS1 ECCPAS0 PSSAC1 PSSAC0 PSSBD1 PSSBD0 0000 0000 37, 127
TMR3H Timer3 Register High Byte xxxx xxxx 38, 113
TMR3L Timer3 Register Low Byte xxxx xxxx 38, 113
T3CON RD16 — T3CKPS1 T3CKPS0 T3CCP1 T3SYNC TMR3CS TMR3ON 0-00 0000 38, 111
SPBRGH EUSART Baud Rate Generator High Byte 0000 0000 38
SPBRG EUSART Baud Rate Generator Low Byte 0000 0000 38, 135
RCREG EUSART Receive Register 0000 0000 38, 143, 
142
TXREG EUSART  Transmit Register 0000 0000 38, 140, 
142
TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 38, 132
RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 000x 38, 133
BAUDCTL — RCIDL —SCKPBRG16— WUE ABDEN -1-1 0-00 38
EEADR EEPROM Address Register 0000 0000 38, 67
EEDATA EEPROM Data Register 0000 0000 38, 70
EECON2 EEPROM Control Register 2 (not a physical register) 0000 0000 38, 58, 67
EECON1 EEPGD CFGS — FREE WRERR WREN WR RD xx-0 x000 38, 59, 68
IPR2 OSCFIP ——EEIP— LVDIP TMR3IP —1--1 -11- 38, 83
PIR2 OSCFIF —— EEIF —LVDIFTMR3IF—0--0 -00- 38, 79
PIE2 OSCFIE ——EEIE— LVDIE TMR3IE —0--0 -00- 38, 81
IPR1 — ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP -111 -111 38, 82
PIR1 — ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF -000 -000 38, 78
PIE1 — ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE -000 -000 38, 80
OSCTUNE —— TUN5 TUN4 TUN3 TUN2 TUN1 TUN0 --00 0000 38, 15
TRISB Data Direction Control Register for PORTB 1111 1111 38, 98
TRISA TRISA7(2) TRISA6(1) — Data Direc tion C on trol R egist er for  PORTA 11-1 1111 38, 89
LATB Read/Write PORTB Data Latch xxxx xxxx 38, 98
LATA LATA<7>(2) LATA<6>(1) — Read/Write PORTA Data Latch xx-x xxxx 38, 89
PORTB Read PORTB pins, Write PORTB Data Latch xxxx xxxx 38, 98
PORTA RA7(2) RA6(1) RA5(4) Read PORTA pins, Write PORTA Data Latch xx0x 0000 38, 89
TABLE 5-2: REGISTER FILE SUMMARY (PIC18F1220/1320) (CONTINUED)
File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR Details on 
page:
Legend: x = unknow n , u = unchanged, – = unimpl emented, q = value depends on condition
Note 1: RA6 and associated bits are configured as port pins in RCIO, ECIO and INTIO2 (with port function on RA6) Oscillator mode only and read ‘0’ 
in all other oscillator modes.
2: RA7 and associated bits are configured as port pins in INTIO2 Oscillator mode only and read ‘0’ in all other modes.
3: Bit 21 of the PC is only available in Test mode and Serial Programming modes.
4: The RA5 port bit is only available when MCLRE fuse (CONFIG3H<7>) is programmed to ‘0’. Otherwise, RA5 reads ‘0’. This bit is read-only.

PIC18F1220/1320

5.10 Access Bank

The Access Bank is an architectural enhancement

which is very useful for C compiler code optimization.

The techniques used by the C compiler may also be

useful for programs written in assembly.

This data memory region can be used for:

• Intermediate computational values

• Local variables of subroutines

• Faster context saving/switching of variables

• Comm on va riab les

• Faster evaluation/control of SFRs (no banking)

The Access Bank is comprised of the last 128 bytes in

Bank 15 (SFRs) and the first 128 bytes in Bank 0.

These two sections will be referred to as Access RAM

High and Access RAM Low, respectively. Figure 5-6

indicates the Access RAM areas.

A bit in the instruc tio n w ord sp ec ifie s if the opera tion is

to occur i n the bank sp ec ifi ed by the BSR regis ter o r in

the Access Bank. This bit is denoted as the ‘a’ bit (for

access bit).

When forced in the Access Bank (a = 0), the last

address in Access RAM Low is followed by the first

address in Access RAM High. Access RAM High maps

the Special Function Registers, so these registers can

be accessed without any software overhead. This is

useful for testing status flags and modifying control bits.

5.11 Bank Select Register (BSR)

The need for a large general purpose memory space

dictates a RAM banking scheme. The data memory is

parti tion ed into as ma ny as sixtee n ban ks. When using

direct addressing, the BSR should be configured for the

desired bank.

BSR<3:0> holds the upper 4 bits of the 12-bit RAM

address. The BSR<7:4> bits will always read ‘0’s and

writes will have no effect (see Figure 5-7).

A MOVLB instruction has been provided in the instruction

set to assist in selecting banks.

If the currently selected bank is not implemented, any

read will return all ‘0’s and all writes are ignored. The

S tatus register bit s will be set/cleared as appro priate for

the instruction performed.

Each Bank extends up to FFh (256 bytes). All data

memory is implemented as static RAM.

A MOVFF ins truct ion ig nores the BS R, sin ce th e 12- bit

addresses are embedded into the instruction word.

Section 5.12 “Indirect Addressing, INDF and FSR

Registers” provides a description of indirect address-

ing, which allows linear addressing of the entire RAM

space.

FIGURE 5-7: DIRECT ADDRESSING

Note 1: For register file map detail, see Table 5-1.

2: The access bit of the instruction can be used to force an override of the selected bank (BSR<3:0>) to the registers

of the Access Bank.

3: The MOVFF instruction embeds the entire 12-bit address in the instruction.

Data

Memory(1)

Direct Addres sing

Bank Select(2) Location Select(3)

BSR<3:0> 7 0

From Opcode(3)

00h 01h 0Eh 0Fh

Bank 0 Bank 1 Bank 14 Bank 15

1FFh

100h

0FFh

000h

EFFh

E00h

FFFh

F00h

BSR<7:4>

0000

PIC18F1220/1320

5.12 Indirect Addressing, INDF and

FSR Registers

Indir ect addressing is a mod e of addressing dat a mem-

ory, where the data memory address in the instruction

is not fi xe d. An FSR reg is ter i s u se d as a poi nter to the

data memory locat ion that is to be read or written. Since

this poi nter i s in RAM, the con ten t s c an be mo difi ed by

the program. This can be useful for data tables in the

data memory and for software stacks. Figure 5-8

shows how the fetched instruction is modified prior to

being executed.

Indirect addressing is possible by using one of the

INDF registers. Any instruction, using the INDF regis-

ter, actually acce sses the reg ister poin ted to by the Fil e

Select Register, FSR. Reading the INDF register itself,

indirectly (FSR = 0), will read 00h. Writing to the INDF

FSR regi ster cont ains a 12 -bit add ress, which is shown

in Figure 5-9.

The INDFn register is not a physical register. Address-

ing INDFn actually addresses the register whose

address is contained in the FSRn register (FSRn is a

pointer). This is indirect addr essing.

Exampl e 5-5 shows a s imple use o f indirect add ressing

to clear the RAM in Bank 1 (locations 100h-1FFh) in a

minimum number of instructions.

EXAMPLE 5-5: HOW TO CLEAR RAM

(BANK 1) USING

INDIRECT ADDRESSING

There are three indirect addressing registers. To

address the entire data memory space (4096 bytes),

these registers are 12-bit wide. To store the 12 bits of

addressing information, tw o 8-bit registers are required:

1. FSR0: composed of FSR0H:FSR0L

2. FSR1: composed of FSR1H:FSR1L

3. FSR2: composed of FSR2H:FSR2L

In addition, there are registers INDF0, INDF1 and

INDF2, which are not physically implemented. Reading

or writing to these registers activates indirect address-

ing, with the value in the corresponding FSR register

being the ad dress of the data. If an i nstruct ion w rite s a

value t o IN DF0, the val ue w ill be wr itt en to t he address

pointed to by FSR0H:FSR0L. A read f rom INDF 1 reads

the data from the address pointed to by

FSR1H:FSR1L. INDFn can be used in code anywhere

an operand can be used.

If INDF0, INDF1 or INDF2 are read indirectly via an

FSR, all ‘0’s are read (zero bit is set). Similarly, if

INDF0, INDF1 or INDF2 are written to indirectly, the

operation will be equivale nt to a NOP instruction and the

Status bits are not affected.

5.12.1 INDIRECT ADDRESSING

OPERATION

Each FSR register has an INDF register ass ociated with

it, plus four additional register addresses. Performing an

operation using one of these five registers determines

how the FSR will be modified during indirect addressing.

When data access is performed using one of the five

INDFn locations, the address selected will configure

the FSRn register to:

• Do nothing to FSRn after an indirect access (no

change) – INDFn

• Auto-decr ement FSRn after an indirect access

(post-decrement) – POSTDECn

• Auto-increment FSRn after an indirect access

(post-increment) – POSTINCn

• Auto- inc rement FS Rn befo re an indirect access

(pre-increment) – PREINCn

• Use the value in the WREG register as an offset

to FSRn . Do not modif y the value of the WREG or

the FSRn register after an indirect access (no

change) – PLUSWn

When using the auto-increment or auto-decrement

features, the effect on the FSR is not reflected in the

Status register. For example, if the indirect address

causes the FSR to equal ‘0’, the Z bit will not be set.

Auto-incrementing or auto-decrementing an FSR affects

all 12 bits. That is, when FSRnL overflows from an

increment, FSRnH will be incremented automatically.

Adding these features allows the FSRn to be used as a

stac k pointer, in addition to it s uses for tab le operation s

in d ata me mory.

Each FSR has an address associated with it that

performs an indexed indirect access. When a data

access to this INDFn location (PLUSWn) occurs, the

FSRn is configured to add the signed value in the

WREG register and the value in FSR to form the

address before an indirect access. The FSR value is

not cha nge d. The WR EG offset ran ge is -128 to +1 27 .

If an FSR regist er conta ins a value that poin ts to one of

the INDFn, an indirect read will read 00h (zero bit is

set), while an indirect write will be equivalent to a NOP

(Status bits are not affected).

If an indirect addressing write is performed when the tar-

get address is an FSRnH or FSRnL register, the data is

writte n to the F SR regist er , but no pre- or p ost-inc rement/

decrement is performed.

LFSR FSR0,0x100 ;

NEXT CLRF POSTINC0 ; Clear INDF

; register then

; inc pointer

BTFSS FSR0H, 1 ; All done with

; Bank1?

GOTO NEXT ; NO, clear next

CONTINUE ; YES, continue

PIC18F1220/1320

FIGURE 5-8: INDIRECT ADDRESSING OPERATION

FIGURE 5-9: INDIRECT ADDRESSING

Opcode Address

File Address = Access of an Indirect Addressing Register

FSR

Instruction

Executed

Instruction

Fetched

RAM

Opcode File

BSR<3:0>

FFFh

Note 1: For register file map detail, see Table 5-1.

Data

Memory(1)

Indirect Addressing

FSRnH:FSRnL

0FFFh

0000h

Location Select

11 0

PIC18F1220/1320

5.13 Status Register

The S tatus register , shown in Register 5-2, contains the

arithmetic status of the ALU. As with any other SFR, it

can be the operand for any inst ruc tio n.

If the Status register is the destina tion for an instruction

that af fect s the Z, DC, C, OV or N bit s, the result s of the

instruction are not written; instead, the status is

updated accord ing to t he inst ruct ion pe rformed. The re-

fore, the res ul t of an ins tru cti on w i th the Status regis ter

as its destinatio n may be dif ferent than intended . As an

example, CLRF STATUS will set the Z bit and leave the

remaining Status bits unchanged (‘000u u1uu’).

It is recommended that only BCF, BSF, SWAPF, MOVFF

and MOVWF instructions are used to alter the Status reg-

ister, because thes e instruction s do not a ffect the Z, C ,

DC, OV or N bits in the Status register.

For other i ns truc tio ns that do not a ffect Status bi t s , se e

the instruction set summaries in Table 20-1.

Note: The C and DC bits operate as the borrow

and digit borrow bits, respectively, in

subtraction.

U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x

— — —NOVZDCC

bit 7 bit 0

bit 7-5 Unimplemented: Read as ‘0’

bit 4 N: Negative bit

This bit is used for signed arithmetic (2’s complement). It indicates whether the result was

negative (ALU MSB = 1).

1 = Result was neg ative

0 = Result was positive

bit 3 OV: Ov erf low bit

This bit is used for signed arithmetic (2’s complement). It indicates an overflow of the

7-bit magnitude, which causes the sign bit (bit 7) to change state.

1 = Overflow occurred for signed arithmetic (i n this ari thmetic operation)

0 = No overflow occurred

bit 2 Z: Zero bit

1 = The result of an arithmetic or logic operation is zero

0 = The result of an arithmetic or logic operation is not zero

bit 1 DC: Digi t carry/bor row bit

For ADDWF, ADDLW, SUBLW and SUBWF instructions:

1 = A carry-out from the 4th low-order bit of the result occurred

0 = No carry-out from the 4th low-order bit of the result

Note: For borrow, the polarity is reversed. A subtraction is executed by adding the

2’s complement of the second operand. For rotate (RRF, RLF) instructions, this bit

is loaded with either the bit 4 or bit 3 of the source register.

bit 0 C: Carry/borrow bit

For ADDWF, ADDLW, SUBLW and SUBWF instructions:

1 = A carry-out from the Most Significant bit of the result occurred

0 = No carry-out from the Most Significant bit of the result occurred

Note: For borrow, the polarity is reversed. A subtraction is executed by adding the

2’s complement of the second operand. For rotate (RRF, RLF) instructions, this bit

is loaded with either the high or low-order bit of the source register.

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘ 0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

5.14 RCON Register

The Reset Control (RCON) register contains flag bits

that allow differentiation between the sources of a

device Reset. These flags include the TO, PD, POR,

BOR and RI bi ts. Thi s register is re adable an d writ able.

Note 1: If the BOR configu ration bit is set (Bro wn-

out Reset enabled), the BOR bit is ‘1’ on

a Power-on Reset. After a Brown-out

Reset has occurred, the BOR bit will be

cleared and must be set by firmware to

indicate the occurrence of the next

Brown-out Reset.

2: It is re commended that the POR bit be set

after a Power-on Reset has been

detected, so that subsequent Power-on

Resets may be detect ed.

R/W-0 U-0 U-0 R/W-1 R-1 R-1 R/W-0 R/W-0

IPEN ——RITO PD POR BOR

bit 7 bit 0

bit 7 IPEN: Interrupt Priority Enable bit

1 = Enable priority levels on interrupts

0 = Disable priority levels on interrupts (PIC16CXXX Compatibility mode)

bit 6-5 Unimplemented: Read as ‘0’

bit 4 RI: RESET Instruction Flag bit

1 = The RESET instruction was not executed (set by firmware only)

0 = The RESET instruction was executed causing a device Reset

(must be set in software after a Brown-out Reset occurs)

bit 3 TO: Watchdog Time-out Flag bit

1 = Set by power-up, CLRWDT instruction or SLEEP instruction

0 = A WDT time-out occurred

bit 2 PD: Power-down Detection Flag bit

1 = Set by power-up or by the CLRWDT instructi on

0 = Cleared by execution of the SLEEP instruction

bit 1 POR: Power-on Reset Status bit

1 = A Power-on Reset has not occurred (set by firmware only)

0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)

bit 0 BOR: Br own-out Reset Status bit

1 = A Brown-out Reset has not occurred (set by firmware only)

0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

6.0 FLASH PROGRAM MEMORY

The Flash program memory is readable, writable and

erasable during normal operation over the entire VDD

range.

A read from program memory is executed on one byte

at a time. A write to program memory is executed on

blocks o f 8 bytes at a ti me . Pro gram m em ory is er ase d

in bloc ks of 64 by tes at a time. A “Bu lk Erase” oper ation

may not be issued from user code.

While writing or erasing program memory, instruction

fetches cease until the operation is complete. The

program memory cannot be accessed during the write

or erase, therefore, code cannot execute. An internal

programming timer terminates program memory writes

and erases.

A value wri tten to program memory does not need to be

a valid instruction. Executing a program memory

location that forms an invalid instruction results in a

NOP.

6.1 Table Reads and Table Writes

In order to read and write program memory, there are

two o per atio ns that al low the proc ess or t o mov e byt es

between the program memory space and the data

RAM:

• Table Read (TBLRD)

• Table Write (TBLWT)

The program memory space is 16 bits wide, while the

data RAM space is 8 bits wide. Table reads and table

writes move data between these two memory spaces

through an 8-bit register (TABLAT).

Table read operations retrieve data from program

memory and place it into TABLAT in the data RAM

space. Figure 6-1 shows the operation of a table read

with program memo ry and data RAM.

Table write operations store data from TABLAT in the

data memory space into holding registers in program

memory. The procedure to write the contents of the

holding registers into program memory is detailed in

Section 6.5 “Writing to Flash Program Memory”.

Figure 6-2 shows the operation of a table write with

program memory and data RAM.

Table operations work with byte entities. A table block

cont aining dat a, rather than program instruct ions, is not

required to be word aligned. Therefore, a table block

can st art and en d at any by te address. If a tab le write is

being used to write executable code into program

memory, program instructions will need to be word

aligned (TBLPTRL<0> = 0).

The EEPROM on-chip timer controls the write and

erase times. The write and erase voltages are gener-

ated by an on-chip charge pump rated to operate over

the voltage range of the device for byte or word

operations.

FIGURE 6-1: TABLE READ OPERATION

Table Pointer(1) Table Latch (8-bit)

Program Mem ory

TBLPTRH TBLPTRL TABLAT

TBLPTRU

Instruction: TBLRD*

Note 1: Table Pointer points to a byte in program memory.

Program Me mory

(TBLPTR)

PIC18F1220/1320

FIGURE 6-2: TABLE WRITE OPERATION

6.2 Control Registers

Several control registers are used in conjunction with

the TBLRD and TBLWT instructions. These include the:

• EECON1 register

• EECON2 register

• TABLAT register

• TBLPTR registers

6.2.1 EECON1 AND EECON2 REGISTERS

EECON1 is the control register for memory accesses.

EECON2 is not a physical register. Reading EECON2

will read all ‘0’s. The EECON2 register is used

exclusively in the memory write and erase sequences.

Control bit , EEPGD, dete rmine s if the a cc ess wil l be to

program or data EEPROM memory. When clear,

operations will access the data EEPROM memory.

When set, program memory is accessed.

Control bit, CFGS, determines if the access will be to

the confi guratio n regis ters, or to p rogram mem ory/da ta

EEPROM memory. When set, subsequent operations

access configuration registers. When CFGS is clear,

the EEPGD bit selects either program Flash or data

EEPROM memory.

The FREE bit controls program memory erase opera-

tions. When the FREE bit is set, the erase operation is

initiated on the next WR command. When FREE is

clear, only writes are enabled.

The WREN bit enables and disables erase and write

operations. When set, erase and write operations are

allowed. When clear, erase and write operations are

disabl ed – the WR bit cannot be set w hile the W REN bit

is cle ar . Thi s proces s help s to pre vent accid ental writes

to memory du e to errant (unexp ected) code execution.

Firmware should keep the WREN bit clear at all times,

except when starting erase or write operations. Once

firmware has set the WR bit, the WREN bit may be

cleared. Clearing the WREN bit will not affect the

operation in progress.

The WRERR bit is set when a write operation is

interrupte d by a Reset. In these situati ons, the user ca n

check the WRERR bit and rewrite the location . It will b e

necessary to reload the data and address registers

(EEDAT A and EEAD R) as these registers have cleare d

as a result of the Reset.

Control bits, RD and WR, start read and erase/write

operatio ns, respectiv ely . Thes e bits are se t by firmware

and cleared by hardware at the completion of the

operation.

The RD bit cannot be set when accessing program

memory (EEPGD = 1). Program memory is read using

table read instructio ns. See Se ction 6.3 “Reading the

Flash Program Memory” regarding table reads.

Table Pointer(1) Table Latch (8-bit)

TBLPTRH TBLPTRL TABLAT

Program Memory

(TBLPTR)

TBLPTRU

Instruction: TBLWT*

Note 1: Table Pointer actually points to one of eight holding registers, the address of which is determined by

TBLPTRL<2:0>. The process for physically writing data to the program mem o ry array is discuss ed

in Section 6.5 “Writing to Flash Program Memory”.

Holding Registers

Program Mem ory

Note: Interru pt flag bi t, EEIF in t he PIR2 regi ster,

is set when the write is complete. It must

be cleared in sof tw are.

PIC18F1220/1320

R/W-x R/W-x U-0 R/W-0 R/W-x R/W-0 R/S-0 R/S-0

EEPGD CFGS — FREE WRERR WREN WR RD

bit 7 bit 0

bit 7 EEPGD: Flash Program or Data EEPROM Memory Select bit

1 = Access pro gram Fl ash memory

0 = Access data EEPROM memory

bit 6 CFGS: Flash Program/Data EE or Configuration Select bit

1 = Access configuration registers

0 = Access program Flash or data EEPROM memory

bit 5 Unimplemented: Read as ‘0’

bit 4 FREE: Flash Row Erase Enable bit

1 = Erase the program memory row addressed by TBLPTR on the next WR command

(cleared by completion of erase operation – TBLPTR<5:0> are ignored)

0 = Perform write onl y

bit 3 WRERR: EEPROM Error Flag bit

1 = A write operation was prematurely terminated (any Reset during self-timed programming)

0 = The write operation completed normally

Note: When a WRERR occurs, the EEPGD and CFGS bits are not cleared. This allows

tracing of the error condition.

bit 2 WREN: Write Enable bit

1 = Allows eras e or write cycles

0 = Inhibits erase or write cycles

bit 1 WR: Write Control bit

1 = Initiates a data EEPROM erase/write cycle or a program memory erase cycle or write cycle.

(The operatio n is self- timed and the bit is cleared by hard ware once wri te is comple te. The

WR bit can only be set (not cleared) in software.)

0 = Write cycle completed

bit 0 RD: Read Control bit

1 = Initiates a memory read

(Read t akes one cycle. R D is cleared in ha rdware. The RD bit can only be set (not cleare d)

in software. RD bit cannot be set when EEPGD = 1.)

0 = Read completed

Legend:

R = Readable bit S = Settable only U = Unimplemented bit, read as ‘0’

W = Writable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared

x = Bit is unknown

PIC18F1220/1320

6.2.2 TABLAT – TABLE LATCH REGISTER

The Table Latch (TABLAT) is an 8-bit register mapped

into the SFR spa ce. The table latch is use d to hold 8-bit

data during data transfers between program memory

and data RAM.

6.2.3 TBLPTR – TABLE POINTER

The Table Pointer (TBLPTR) addresses a byte within

the program memory. The TBLPTR is comprised of

three SFR registers: Table Pointer Upper Byte, Table

Pointer High Byte and Table Pointer Low Byte

(TBLPTRU:TBLPTRH:TBLPTRL). These three regis-

ters join to form a 22-bit wide pointer. The low-order

21 bits allow the device to address up to 2 Mbytes of

program memory space. Setting the 22nd bit allows

access to the device ID, the user ID and the

configuration bits.

The Table Pointer (TBLPTR) register is used by the

TBLRD and TBLWT instructi ons . T hes e i ns truc t io ns ca n

update the TBLPTR in one of four ways based on the

table operation. These operations are shown in

Table 6-1. Th ese operations on th e TBLPTR onl y affect

the low-orde r 21 bi ts.

6.2.4 TABLE POINTER BOUNDARIES

TBLPTR is used in reads, writes and erases of the

Flash program memory.

When a TBLRD is executed, all 22 bits of the Table

Pointer determine which byte is read from program or

configuration memory into TABLAT.

When a TBLWT is executed, the three LSbs of the Table

Pointer (TBLPTR<2:0>) determine which of the eight

program memory holding registers is written to. When

the timed write to program memory (long write) begins,

the 19 MSbs of the Table Pointer (TBLPTR<21:3>) will

determine which program memory block of 8 bytes is

written to (TBLPTR<2:0> are ignored). For more detail,

see Section 6.5 “Writing to Flash Program Memory”.

When an erase of program memory is executed, the

16 MSbs of the Table Pointer (TBLP TR<21 :6>) point to

the 64-byte block that will be erased. The Least

Significant bits (TBLPTR<5:0>) are ignored.

Figure 6-3 describes the relevant boundaries of

TBLPTR based on Flash program memory operations.

TABLE 6-1: TABLE POINTER OPERATIONS WITH TBLRD AND TBLWT INSTRUCTIONS

FIGURE 6-3: TABLE POINTER BOUNDARIES BASED ON OPERATION

Example Operation on Table Pointer

TBLRD*

TBLWT* TBLPTR is not modif ied

TBLRD*+

TBLWT*+ TBLPTR is incremented after the read/write

TBLRD*-

TBLWT*- TBLPTR is decremented after the read/write

TBLRD+*

TBLWT+* TBLP TR is incr em en ted before the read /write

21 16 15 87 0

ERASE – TBLPTR<21:6>

LONG WRITE – TBLPTR<21:3>

READ or WRITE – TBLPTR<21:0 >

TBLPTRL

TBLPTRH

TBLPTRU

PIC18F1220/1320

6.3 Reading the Flash Program

Memory

The TBLRD instruction is used to retrieve data from

program memory and place it into data RAM. Table

reads fro m program memory are pe rformed one byte at

a time.

TBLPTR points to a byte address in program space.

Executing a TBLRD instruction places the byte pointed

to into TABLAT. In addition, TBLPTR can be modified

automatically for the next table read operation.

The interna l program memory is typically org anized by

words. The Least Significan t bit of th e address selects

between the high and low bytes of the word. Figure 6-4

shows the interface between the internal program

memory and the TABLAT.

FIGURE 6-4: READS FROM FLASH PROGRAM MEMORY

EXAMPLE 6-1: READING A FLASH PROGRAM MEMORY WORD

Odd (High) Byte

Program Memory

Even (Low) Byte

TABLAT

TBLPTR

Instruction Register

(IR) Read Register

LSB = 1

TBLPTR

LSB = 0

MOVLW CODE_ADDR_UPPER ; Load TBLPTR with the base

MOVWF TBLPTRU ; address of the word

MOVLW CODE_ADDR_HIGH

MOVWF TBLPTRH

MOVLW CODE_ADDR_LOW

MOVWF TBLPTRL

READ_WORD

TBLRD*+ ; read into TABLAT and increment TBLPTR

MOVFW TABLAT ; get data

MOVWF WORD_EVEN

TBLRD*+ ; read into TABLAT and increment TBLPTR

MOVFW TABLAT ; get data

MOVWF WORD_ODD

PIC18F1220/1320

6.4 Erasing Flash Program Memory

The minimum erase block size is 32 words or 64 bytes

under firmware control. Only through the use of an

external programmer, or through ICSP control, can

larger blo cks of program m emory be bulk eras ed. Word

erase in Flash memory is not supported.

When initiating an erase sequence from the micro-

controll er itsel f, a block of 64 by tes of program me mory

is erased. The Most Significant 16 bits of the

TBLPTR<21:6> point to the block being erased.

TBLPTR<5:0> are ignored.

The EECON1 regis te r com ma nds the era se operation.

The EEPGD bit must be set to point to the Flash

program memory. The CFGS bit must be clear to

access program Flash and data EEPROM memory.

The WREN bit must be set to enable write operations.

The FREE bit is set to select an erase operation. The

WR bit is set as part of the required instruction

sequence (as shown in Example 6-2) and starts the

actual erase operation. It is not necessary to load the

TABLAT register with any data as it is ignored.

For protection, the write initiate sequence using

EECON2 must be used.

A long w rite i s nec essary for erasing th e inte rnal Fl ash.

Instruction execution is halted while in a long write

cycle. The long write will be terminated by the internal

program ming timer.

6.4.1 FLASH PROGRAM MEMORY

ERAS E S EQ UE N CE

The sequence of events for erasing a block of internal

program memory location is:

1. Load Table Pointer with address of row being

erased.

2. Set the EECON1 register for the erase operation:

• set EEPGD bit to point to program memory;

• clear the CFGS bit to access program

memory;

• set WREN bit to enable writes;

• set FREE bit to enable the erase.

3. Disable int errup ts.

4. Write 55h to EECON2.

5. Write AAh to EECON2.

6. Set the WR bit. This will begin the row erase

cycle.

7. The CPU will stall for duration of the erase

(about 2 ms using internal timer).

8. Execute a NOP.

9. Re-enable interrupts.

EXAMPLE 6-2: ERASING A FLASH PROGRAM MEMORY ROW

MOVLW CODE_ADDR_UPPER ; load TBLPTR with the base

MOVWF TBLPTRU ; address of the memory block

MOVLW CODE_ADDR_HIGH

MOVWF TBLPTRH

MOVLW CODE_ADDR_LOW

MOVWF TBLPTRL

ERASE_ROW

BSF EECON1, EEPGD ; point to FLASH program memory

BSF EECON1, WREN ; enable write to memory

BSF EECON1, FREE ; enable Row Erase operation

BCF INTCON, GIE ; disable interrupts

MOVLW 55h

MOVWF EECON2 ; write 55H

Required MOVLW AAh

Sequence MOVWF EECON2 ; write AAH

BSF EECON1, WR ; start erase (CPU stall)

NOP

BSF INTCON, GIE ; re-enable interrupts

PIC18F1220/1320

6.5 Writing to Flash Program Memory

The programming block size is 4 words or 8 bytes.

Word or byte programming is not supported.

Table writes are used internally to load the holding

registers needed to program the Flash memory. There

are 8 holding registers used by the table writes for

programming.

Since the Table Latch (TABLAT) is only a single byte,

the TBLWT instruction must be executed 8 times for

each programming operation. All of the table write

operations will essentiall y be short wri tes, because only

the hold ing re gisters are w ritte n. At the end of upda ting

8 registers , the EECON1 register must be w ritten to, to

start the programming operation with a long write.

The long write is necessary for programming the

internal Flash. Ins tructio n execu tion is halted whil e in a

long write cycle. The long write will be terminated by

the internal programming timer.

FIGURE 6-5: TABLE WRITES TO FLASH PROGRAM MEMORY

6.5.1 FLASH PROGRAM MEMORY WRITE

SEQUENCE

The sequence of events for programming an internal

program memory location should be:

1. Read 64 bytes into R AM.

2. Update data values in RAM as necessary.

3. Load Table Pointer with address being erased.

4. Do the row erase procedure (see Section 6.4.1

“Flash Program Memory Erase Sequence”).

5. Load Table Pointer with address of first byte

being written.

6. Write the first 8 bytes into the holding registers

with auto-increment.

7. Set the EECON 1 register for the wri te operation:

• set EEPGD bit to point to program memory;

• clear the CFGS bit to access program

memory;

• set WREN bit to enable byte writes.

8. Disable int errup ts.

9. Write 55h to EECON2.

10. Write AAh to EECON2.

11. Set the WR bit. This will begin the w rite cy cl e.

12. The CPU wil l st all for d uration o f the write (about

2 ms using internal timer).

13. Execute a NOP.

14. Re-enable interrupts.

15. Repeat steps 6-14 seven times to write

64 bytes.

16. Verify the memory (table read).

This procedure will require about 18 ms to update one

row of 64 bytes of memory. An example of the required

code is given in Example 6-3.

Holding Register

TABLAT

Holding Register

TBLPTR = xxxxx7

Holding Register

TBLPTR = xxxxx1

Holding Register

TBLPTR = xxxxx0

88 8 8

Write Register

TBLPTR = xxxxx2

Program Memory

PIC18F1220/1320

EXAMPLE 6-3: WRITING TO FLASH PROGRAM MEMORY

MOVLW D'64 ; number of bytes in erase block

MOVWF COUNTER

MOVLW BUFFER_ADDR_HIGH ; point to buffer

MOVWF FSR0H

MOVLW BUFFER_ADDR_LOW

MOVWF FSR0L

MOVLW CODE_ADDR_UPPER ; Load TBLPTR with the base

MOVWF TBLPTRU ; address of the memory block

MOVLW CODE_ADDR_HIGH

MOVWF TBLPTRH

MOVLW CODE_ADDR_LOW ; 6 LSB = 0

MOVWF TBLPTRL

READ_BLOCK

TBLRD*+ ; read into TABLAT, and inc

MOVF TABLAT, W ; get data

MOVWF POSTINC0 ; store data and increment FSR0

DECFSZ COUNTER ; done?

GOTO READ_BLOCK ; repeat

MODIFY_WORD

MOVLW DATA_ADDR_HIGH ; point to buffer

MOVWF FSR0H

MOVLW DATA_ADDR_LOW

MOVWF FSR0L

MOVLW NEW_DATA_LOW ; update buffer word and increment FSR0

MOVWF POSTINC0

MOVLW NEW_DATA_HIGH ; update buffer word

MOVWF INDF0

ERASE_BLOCK

MOVLW CODE_ADDR_UPPER ; load TBLPTR with the base

MOVWF TBLPTRU ; address of the memory block

MOVLW CODE_ADDR_HIGH

MOVWF TBLPTRH

MOVLW CODE_ADDR_LOW ; 6 LSB = 0

MOVWF TBLPTRL

BCF EECON1, CFGS ; point to PROG/EEPROM memory

BSF EECON1, EEPGD ; point to FLASH program memory

BSF EECON1, WREN ; enable write to memory

BSF EECON1, FREE ; enable Row Erase operation

BCF INTCON, GIE ; disable interrupts

MOVLW 55h ; Required sequence

MOVWF EECON2 ; write 55H

MOVLW AAh

MOVWF EECON2 ; write AAH

BSF EECON1, WR ; start erase (CPU stall)

NOP

BSF INTCON, GIE ; re-enable interrupts

WRITE_BUFFER_BACK

MOVLW 8 ; number of write buffer groups of 8 bytes

MOVWF COUNTER_HI

MOVLW BUFFER_ADDR_HIGH ; point to buffer

MOVWF FSR0H

MOVLW BUFFER_ADDR_LOW

MOVWF FSR0L

PROGRAM_LOOP

MOVLW 8 ; number of bytes in holding register

MOVWF COUNTER

PIC18F1220/1320

EXAMPLE 6-3: WRITING TO FLASH PROGRAM MEMORY (CONTINUED)

6.5.2 WRITE VERIFY

Depending on the application, good programming

practice may dictate that the value written to the mem-

ory should be verified against the original value. This

should be used in applications where excessive writes

can stress bits near the specification limit.

6.5.3 UNEXPECTED TERMINATION OF

WRITE OPERATION

If a wri te is term in ate d by an unpl an ned ev en t, s uc h a s

loss of power or an unexpected Reset, the memory

locatio n jus t progra mmed shou ld be verifi ed and repr o-

grammed if needed. The WRERR bit is set when a

write operation is interrupted by a MCLR Reset, or a

WDT T im e-out Reset during norm al operation. In these

situati ons, users c an check the WRERR bit and rewri te

the location.

6.6 Flash Program Operation Duri ng

Code Protection

See Section 19.0 “Special Features of the CPU” for

details on code protection of Flash program memory.

TABLE 6-2: REGISTERS ASSOCIATED WITH PROGRAM FLASH MEMORY

WRITE_WORD_TO_HREGS

MOVF POSTINC0, W ; get low byte of buffer data and increment FSR0

MOVWF TABLAT ; present data to table latch

TBLWT+* ; short write

; to internal TBLWT holding register, increment

TBLPTR

DECFSZ COUNTER ; loop until buffers are full

GOTO WRITE_WORD_TO_HREGS

PROGRAM_MEMORY

BCF INTCON, GIE ; disable interrupts

MOVLW 55h ; required sequence

MOVWF EECON2 ; write 55H

MOVLW AAh

MOVWF EECON2 ; write AAH

BSF EECON1, WR ; start program (CPU stall)

NOP

BSF INTCON, GIE ; re-enable interrupts

DECFSZ COUNTER_HI ; loop until done

GOTO PROGRAM_LOOP

BCF EECON1, WREN ; disable write to memory

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on:

POR, BOR

Value on

all other

Resets

TBLPTRU —— bit 21 Program Memory Table Pointer Upper Byte (TBLP TR<20 :16>) --00 0000 --00 0000

TBPLTRH Program Memory Table Pointer High Byte (TBLPTR<15:8>) 0000 0000 0000 0000

TBLPTRL Program Mem ory Table Pointer High Byte (TBLPTR<7:0>) 0000 0000 0000 0000

TABLAT Program Memory Table Latch 0000 0000 0000 0000

INTCON GIE/GIEH PEIE/GIEL TMR0IE INTE RBIE TMR0IF INTF RBIF 0000 000x 0000 000u

EECON2 EEPROM Control Register 2 (not a physical register) ——

EECON1 EEPGD CFGS — FREE WRERR WREN WR RD xx-0 x000 uu-0 u000

IPR2 OSCFIP ——EEIP — LVDIP TMR3IP —1--1 -11- 1--1 -11-

PIR2 OSCFIF ——EEIF — LVDIF TMR3IF —0--0 -00- 0--0 -00-

PIE2 OSCFIE ——EEIE — LVDIE TMR3IE —0--0 -00- 0--0 -00-

Legend: x = unknown, u = unchanged, – = unimplemented, read as ‘0’.

Shaded cells are not used during Flash/EEPROM access.

PIC18F1220/1320

NOTES:

PIC18F1220/1320

7.0 DATA EEPROM MEMORY

The data EEPROM is readable and writable during

normal operation over the entire VDD ra nge. The d ata

memory is not directly mapped in the register file

space. Instead, it is indirectly addressed through the

Special Function Registers (SFR).

There are four SFRs used to read and write the

program and data EEPROM memory. These registers

are:

• EECON1

• EECON2

• EEDATA

• EEADR

The EEPROM dat a memory allows byte read and write.

When interfacing to the data memory block, EEDATA

holds the 8-bit data for read/write and EEADR holds the

address of the EEPROM location being accessed.

These devices have 256 bytes of data EEPROM with

an address range from 00h to FFh.

The EEPROM data memory is rated for high erase/

write cycle endurance. A byte write automatically

erases the location and writes the new data (erase-

befor e-write). The wr ite time is control led by an on- chip

timer. The write time will vary with voltage and

temperature, as well as from chip to chip. Please

refer to parameter D122 (Table 22-1 in Section 22.0

“Electri cal Characteristics”) for exact limits.

7.1 EEADR

The address register can address 256 bytes of data

EEPROM.

7.2 EECON1 and EECON2 Registers

EECON1 is the control register for memory accesses.

EECON2 is not a physical register. Reading EECON2

will read all ‘0’s. The EECON2 register is used

exclusively in the memory write and erase sequences.

Control bit , EEPGD, dete rmine s if the a cc ess wil l be to

program or data EEPROM memory. When clear,

operations will access the data EEPROM memory.

When set, program memory is accessed.

Control bit, CFGS, determines if the access will be to

the configuration registers or to program memory/data

EEPROM memory. When set, subsequent operations

access configuration registers. When CFGS is clear,

the EEPGD bit selects either program Flash or data

EEPROM memory.

The WREN bit enables and disables erase and write

operations. When set, erase and write operations are

allowed. When clear, erase and write operations are

disabl ed – the WR bit cannot be set w hile the W REN bit

is clear. This mechanism helps to prevent accidental

writes to memory due to errant (unexpected) code

execution.

Firmware should keep the WREN bit clear at all times,

except when starting erase or write operations. Once

firmware has set the WR bit, the WREN bit may be

cleared. Clearing the WREN bit will not affect the

operation in progress.

The WRERR bit is set when a write operation is

interrupte d by a Reset. In these situati ons, the user ca n

check the WRERR bit and rewrite the location. It is

necessary to reload the data and address registers

(EEDATA and EEADR), as these registers have

cleared as a result of the Reset.

Control bits, RD and WR, start read and erase/write

operat ions, respec tively . These bi ts are set by fi rmware

and cleared by hardware at the completion of the

operation.

The RD bit cannot be set when accessing program

memory (EEPGD = 1). Program memory is read using

table read instructions. See Section 6.1 “Table Read s

and Table Writes” regarding table reads.

Note: Interru pt flag bi t, EEIF in t he PIR2 regi ster,

is set when write is complete. It must be

cleared in software.

PIC18F1220/1320

R/W-x R/W-x U-0 R/W-0 R/W-x R/W-0 R/S-0 R/S-0

EEPGD CFGS — FREE WRERR WREN WR RD

bit 7 bit 0

bit 7 EEPGD: Flash Program or Data EEPROM Memory Select bit

1 = Access pro gram Fl ash memory

0 = Access data EEPROM memory

bit 6 CFGS: Flash Program/Data EEPROM or Configuration Select bit

1 = Access configuration or calibration registers

0 = Access program Flash or data EEPROM memory

bit 5 Unimplemented: Read as ‘0’

bit 4 FREE: Flash Row Erase Enable bit

1 = Erase the program memory row addressed by TBLPTR on the next WR command

(cleared by completion of erase operation)

0 = Perform write onl y

bit 3 WRERR: EEPROM Error Flag bit

1 = A write operation was prematurely terminated

(MCLR or WDT Reset during self-timed erase or program operation)

0 = The write operation completed normally

Note: When a WRERR occurs, the EEPGD or FREE bits are not cleared. This allows

tracing of the error condition.

bit 2 WREN: Erase/Write Enable bit

1 = Allows erase/write cycles

0 = Inhibits erase/write cycles

bit 1 WR: Write Control bit

1 = Initiates a data EEPROM erase/write cycle, or a program memory erase cycle, or w rite cycle.

(The operatio n is self-tim ed and the bit is cleared by hard ware once wri te is complete. The

WR bit can only be set (not cleared) in software.)

0 = Write cycle is completed

bit 0 RD: Read Control bit

1 = Initiates a memory read

(Read t akes one cycle. RD is cleared in hardw are. The RD bit can only be set (not cleared)

in software. RD bit cannot be set when EEPGD = 1.)

0 = Read completed

Legend:

R = Readable bit S = Settable only U = Unimplemented bit, read as ‘0’

W = Writable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared

x = Bit is unknown

PIC18F1220/1320

7.3 Reading the Data EEPROM

Memory

To read a data memory location, the user must write th e

address to the EEADR register, clear the EEPGD

control bit (EECON1<7>) and then set control bit, RD

(EECON1<0>). The data is available for the very next

instruction cycle; therefore, the EEDATA register can

be read by the next instruction. EEDATA will hold this

value u ntil another re ad operation, or until it is w ritten to

by the user (during a write operation).

7.4 Writing to the Data EEPROM

Memory

To write an EEPROM data location, the address must

first be written to the EEADR register and the data

written to the EEDATA register. The sequence in

Example 7-2 must be followed to initiate the write cycle.

The write will not begin if this sequence is not exactly

follow ed (write 55h to E ECON2, write AAh to EECON2,

then set WR bit) for each byte. It is strongly recom-

mended that interrupts be disabled during this

code segment.

Additionally, the WREN bit in EECON1 must be set to

enable writes. This mechanism prevents accidental

writes to data EEPROM due to unexpected code exe-

cution (i.e., runaway programs). The WREN bit should

be kept clear at all times, except when updating the

EEPROM. The WREN bit is not cleared by hardware.

After a write sequence has been initiated, EECON1,

EEADR and EEDATA cannot be modified. The WR bit

will be inhibited from being set unless the WREN bit is

set. The WREN bit must be set on a previous instruc-

tion. Both WR a nd WREN c an not be se t with th e s am e

instruction.

At the completion of the write cycle, the WR bit is

cleared in hardware and the EEPROM Interrupt Flag bit

(EEIF) is set. The user may either enable this interrupt

or poll this bit. EEIF must be cleared by software.

7.5 Write Verify

Depending on the application, good programming

practice may dictate that the value written to the

memory should be verified against the original value.

This should be used in applications where excessive

writes can stress bits near the specification limit.

7.6 Protection Against Spurious Wri te

There are conditions when the device may not want to

write to the data EEPROM memory. To protect against

spurious EEPROM writes, various mechanisms have

been built-in. On power-up, the WREN bit is cleared.

Also, the Power-up Timer (72 ms duration) prevents

EEPROM write.

The writ e in iti ate sequence an d the WR EN bi t tog eth er

help prevent an accidental write during brown-out,

power glitch or software malfunction.

EXAMPLE 7-1: DATA E EPROM READ

EXAMPLE 7-2: DATA E EPROM WRITE

MOVLW DATA_EE_ADDR ;

MOVWF EEADR ; Data Memory Address to read

BCF EECON1, EEPGD ; Point to DATA memory

BSF EECON1, RD ; EEPROM Read

MOVF EEDATA, W ; W = EEDATA

MOVLW DATA_EE_ADDR ;

MOVWF EEADR ; Data Memory Address to write

MOVLW DATA_EE_DATA ;

MOVWF EEDATA ; Data Memory Value to write

BCF EECON1, EEPGD ; Point to DATA memory

BSF EECON1, WREN ; Enable writes

BCF INTCON, GIE ; Disable Interrupts

MOVLW 55h ;

Required MOVWF EECON2 ; Write 55h

Sequence MOVLW AAh ;

MOVWF EECON2 ; Write AAh

BSF EECON1, WR ; Set WR bit to begin write

BSF INTCON, GIE ; Enable Interrupts

SLEEP ; Wait for interrupt to signal write complete

BCF EECON1, WREN ; Disable writes

PIC18F1220/1320

7.7 Operation During Code-Protect

Data EEPROM memory has its own code-protect bits in

configuration words. External read and write

operations are disabled if either of these mechanisms

are enabled.

The mic rocontroll er its elf can bo th read and write to the

internal data EEPROM, regardless of the state of the

code-protect configuration bit. Refer to Section 19.0

“Special Features of the CPU” for additional

information.

7.8 Using the Data EEPROM

The data EEPROM is a high endurance, byte address-

able array that has been optimized for the storage of fre-

quently changing information (e.g., program variables or

other data that are updated often). Frequently changing

values will typically be updated more often than specifi-

cation D124. If this is not the c ase, an array refresh must

be performed. For this reason, variables that change

infrequently (such as constants, IDs, calibration, etc.)

should be stored in Flash program m emory.

A simple data EEPROM refresh routine is shown in

Example 7-3.

EXAMPLE 7-3: DATA EEPROM REFRESH ROUTINE

TABLE 7-1: REGISTERS ASSOCIATED WITH DATA EEPROM MEMORY

Note: If data EEPROM is only used to store

constants and/or data that changes rarely,

an array refresh is likely not required. See

specification D124.

CLRF EEADR ; Start at address 0

BCF EECON1, CFGS ; Set for memory

BCF EECON1, EEPGD ; Set for Data EEPROM

BCF INTCON, GIE ; Disable interrupts

BSF EECON1, WREN ; Enable writes

Loop ; Loop to refresh array

BSF EECON1, RD ; Read current address

MOVLW 55h ;

MOVWF EECON2 ; Write 55h

MOVLW AAh ;

MOVWF EECON2 ; Write AAh

BSF EECON1, WR ; Set WR bit to begin write

BTFSC EECON1, WR ; Wait for write to complete

BRA $-2

INCFSZ EEADR, F ; Increment address

BRA Loop ; Not zero, do it again

BCF EECON1, WREN ; Disable writes

BSF INTCON, GIE ; Enable interrupts

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on:

POR, BOR

Valu e on

all other

Resets

INTCON GIE/GIEH PEIE/GIEL TMR0IE INTE RBIE TMR0IF INTF RBIF 0000 000x 0000 000u

EEADR EEPROM Addres s Registe r 0000 0000 0000 0000

EEDATA EEPROM Data Register 0000 0000 0000 0000

EECON2 EEPROM Control Register 2 (not a physical register) — —

EECON1 EEPGD CFGS — FREE WRERR WREN WR RD xx-0 x000 uu-0 u000

IPR2 OSCFIP ——EEIP—LVDIP TMR3IP —1--1 -11- 1--1 -11-

PIR2 OSCFIF ——EEIF—LVDIF TMR3IF —0--0 -00- 0--0 -00-

PIE2 OSCFIE ——EEIE—LVDIE TMR3IE —0--0 -00- 0--0 -00-

Legend: x = unknown, u = unchanged, – = unimplemented, read as ‘0’. Shaded cells are not used during Flash/EEPROM access.

PIC18F1220/1320

8.0 8 x 8 HARD WARE MULTIPLIER

8.1 Introduction

An 8 x 8 hardware multiplier is included in the ALU of

the PIC18F1220/1320 devices. By making the multiply

a har dware operat ion, i t compl etes i n a sing le in struc-

tion cycle. This is an unsigned multiply that gives a

16-bit result. The result is stored into the 16-bit product

affect any flags in the Status register.

Making the 8 x 8 multiplier execute in a single cycle

gives the following adv antages:

• Higher computational throughput

• Reduc es code siz e requ irem en t s for multip ly

algorithms

The performance increase allows the device to be used

in applications previously reserved for Digital Signal

Processors.

Table 8-1 shows a performance comparison between

Enhanced devices using the single-cycle hardware

multiply and performing the same function without the

hardware multiply.

TABLE 8-1: PERFORMANCE COMPARISON

8.2 Operation

Example 8-1 shows the sequence to do an 8 x 8

unsigned multiply. Only one instruction is required

when one arg um ent of the mul tipl y is al ready loade d i n

the WREG register.

Exampl e 8-2 shows the sequence t o do an 8 x 8 signed

multi ply. To acco unt fo r t he sign bits o f the a rgu men ts,

each argument’s Most Significant bit (MSb) is tested

and the appropriate subtractions are done.

EXAMPLE 8-1: 8 x 8 UNSIGNED

MULTIPLY ROUTINE

EXAMPLE 8-2: 8 x 8 SIGNED MULTIPLY

ROUTINE

Routine Multiply Method Program

Memory

(Words)

Cycles

(Max)

Time

@ 40 MHz @ 10 MHz @ 4 MHz

8 x 8 unsigned Without hardware multiply 13 69 6.9 μs 27.6 μs69 μs

Hardware multiply 1 1 100 ns 400 ns 1 μs

8 x 8 signed Without hard ware multiply 33 91 9.1 μs 36.4 μs91 μs

Hardware multiply 6 6 600 ns 2.4 μs6 μs

16 x 16 unsigned Without hardware multiply 21 242 24.2 μs 96.8 μs 242 μs

Hardware multiply 28 2 8 2.8 μs11.2 μs28 μs

16 x 16 signed Without hardware multiply 52 254 25.4 μs 102.6 μs 254 μs

Hardware multiply 35 40 4 μs16 μs40 μs

MOVF ARG1, W ;

MULWF ARG2 ; ARG1 * ARG2 ->

; PRODH:PRODL

MOVF ARG1, W

MULWF ARG2 ; ARG1 * ARG2 ->

; PRODH:PRODL

BTFSC ARG2, SB ; Test Sign Bit

SUBWF PRODH, F ; PRODH = PRODH

; - ARG1

MOVF ARG2, W

BTFSC ARG1, SB ; Test Sign Bit

SUBWF PRODH, F ; PRODH = PRODH

; - ARG2

PIC18F1220/1320

Example 8-3 shows the sequence to do a 16 x 16

unsigned multiply. Equation 8-1 shows the algorithm

that is us ed. The 32-b it result is st ored in four re gisters,

RES3:RES0.

EQUATION 8-1: 16 x 16 UNSIGNED

MULTIPLICATION

ALGORITHM

EXAMPLE 8- 3: 16 x 16 UNSIGNED

MULTIPLY ROUTINE

Example 8-4 shows the sequence to do a 16 x 16

signed multiply. Equation 8-2 shows the algorithm

used. The 32-bit result is stored in four registers,

RES3:RES0. To account for the sign bits of the argu-

ment s, each argum ent p ai rs’ M ost S ignifi cant bit (M Sb)

is tested and the appropriate subtractions are done.

EQUATION 8-2: 16 x 16 SIGNED

MULTIPLICATION

ALGORITHM

EXAMPLE 8-4: 16 x 16 SIGNED

MU LTIPLY ROUTINE

MOVF ARG1L, W

MULWF ARG2L ; ARG1L * ARG2L ->

; PRODH:PRODL

MOVFF PRODH, RES1 ;

MOVFF PRODL, RES0 ;

;

MOVF ARG1H, W

MULWF ARG2H ; ARG1H * ARG2H ->

; PRODH:PRODL

MOVFF PRODH, RES3 ;

MOVFF PRODL, RES2 ;

;

MOVF ARG1L, W

MULWF ARG2H ; ARG1L * ARG2H ->

; PRODH:PRODL

MOVF PRODL, W ;

ADDWF RES1, F ; Add cross

MOVF PRODH, W ; products

ADDWFC RES2, F ;

CLRF WREG ;

ADDWFC RES3,F ;

;

MOVF ARG1H, W ;

MULWF ARG2L ; ARG1H * ARG2L ->

; PRODH:PRODL

MOVF PRODL, W ;

ADDWF RES1, F ; Add cross

MOVF PRODH, W ; products

ADDWFC RES2, F ;

CLRF WREG ;

ADDWFC RES3, F ;

RES3:RES0

= ARG1H:ARG1L • ARG2H:ARG2L

= (ARG1H • ARG2H • 216) +

(ARG1H • ARG2L • 28) +

(ARG1L • ARG2H • 28) +

(ARG1L • ARG2L)

MOVF ARG1L, W

MULWF ARG2L ; ARG1L * ARG2L ->

; PRODH:PRODL

MOVFF PRODH, RES1 ;

MOVFF PRODL, RES0 ;

;

MOVF ARG1H, W

MULWF ARG2H ; ARG1H * ARG2H ->

; PRODH:PRODL

MOVFF PRODH, RES3 ;

MOVFF PRODL, RES2 ;

;

MOVF ARG1L, W

MULWF ARG2H ; ARG1L * ARG2H ->

; PRODH:PRODL

MOVF PRODL, W ;

ADDWF RES1, F ; Add cross

MOVF PRODH, W ; products

ADDWFC RES2, F ;

CLRF WREG ;

ADDWFC RES3, F ;

;

MOVF ARG1H, W ;

MULWF ARG2L ; ARG1H * ARG2L ->

; PRODH:PRODL

MOVF PRODL, W ;

ADDWF RES1, F ; Add cross

MOVF PRODH, W ; products

ADDWFC RES2, F ;

CLRF WREG ;

ADDWFC RES3, F ;

;

BTFSS ARG2H, 7 ; ARG2H:ARG2L neg?

BRA SIGN_ARG1 ; no, check ARG1

MOVF ARG1L, W ;

SUBWF RES2 ;

MOVF ARG1H, W ;

SUBWFB RES3

;

SIGN_ARG1

BTFSS ARG1H, 7 ; ARG1H:ARG1L neg?

BRA CONT_CODE ; no, done

MOVF ARG2L, W ;

SUBWF RES2 ;

MOVF ARG2H, W ;

SUBWFB RES3

;

CONT_CODE

RES3:RES0

= ARG1H:ARG1L • ARG2H:ARG2L

= (ARG1H • ARG2H • 216) +

(ARG1H • ARG2L • 28) +

(ARG1L • ARG2H • 28) +

(ARG1L • ARG2L) +

(-1 • ARG2H<7> • ARG1H:ARG1L • 216) +

(-1 • ARG1H<7> • ARG2H:ARG2L • 216)

PIC18F1220/1320

9.0 INTERRUPTS

The PIC18F1220/1320 devices have multiple interrupt

sources and an interrupt priority feature that allows

each interrupt source to be assigned a high priority

level or a low priority level. The high priority interrupt

vector is at 000008h and the low priority interrupt vector

is at 000018h. High priority interrupt events will

interrupt any low priority interrupts that may be in

progress.

There are ten registers which are used to control

interrupt operation. These registers are:

• RCON

•INTCON

• INTCON2

• INTCON3

• PIR1, PIR2

• PIE1, PIE2

• IPR1, IPR2

It is recommended that the Microchip header files

suppli ed with MP LAB® IDE be used fo r the symb olic bit

names in these registers. This allows the assembler/

compil er to automa tical ly ta ke care of the pla ceme nt of

these bits within the specified register.

In general, each interrupt source has three bits to

control its operation. The functions of these bits are:

• Flag bit to indicate that an interrupt event

occurred

• Enable bit that allows program execution to

branch to the interrupt vector address when the

flag bit is set

• Priority bit to select high priority or low priority

(INT0 has no priority bit and is al ways high priorit y)

The interrupt priority feature is enabled by setting the

IPEN bit (RCON<7>). When interrupt priority is

enabled, there are two bits which enable interrupts

globall y. Setting the GIEH bit (INTCO N<7>) enable s all

interrupts that have the priority bit set (high priority).

Setting the GIEL bit (INTCON<6>) enables all

inter rupts that have the pr iority bit cleared ( low prio rity).

When the interrupt flag, enable bit and appropriate

global interrupt enable bit are set, the interrupt will

vector immediately to address 000008h or 000018h,

depending on the priority bit setting. Individual

interrupts can be disabled through their corresponding

enable bits.

PIC18F1220/1320

When the IPEN bit is cleared (default state), the

interrupt priority feature is disabled and interrupts are

compatible with PICmicro mid-range devices. In

Compatibility mode, the interrupt priority bits for each

source have no effect. INTCON<6> is the PEIE bit,

which enables/dis ables all pe ripheral interru pt sources.

INTCON<7> is the GIE bit, which enables/disables all

interrupt sources. All interrupts branch to address

000008h in Compatibility mode.

When an interrupt is responded to, the global interrupt

enable bit is cleared to disable further interrupts. If the

IPEN bit is cleared, this is the GIE bit. If interru pt priority

levels are used, this wi ll be either the GIEH or G IEL bit.

High priority interrupt sources can interrupt a low

priority interrupt. Low priority interrupts are not

process ed while high priority int errupt s are in progr ess.

The return address is pushed onto the stack and the

PC is loaded with the interrupt vector address

(000008h or 000018h). Once in the Interrupt Service

Routine, the source(s) of the interrupt can be deter-

mined by polling the interrupt flag bits. The interrupt

flag bit s must be cleared in software be fore re-enab ling

interrupts to avoid recursive interrupts.

The “return from interrupt” instruction, RETFIE, exits

the interrupt routine and sets the GIE bit (GIEH or

GIEL, if priority levels are used), which re-enables

interrupts.

For external interrupt events, such as the INT pins or

the POR TB input chang e interrupt, the i nterrupt latenc y

will be three to four instruction cycles. The exact

latency is the same for one or two-cycle instructions.

Individual interrupt flag bits are set, regardless of the

status of their corresponding enable bit or the GIE bit.

FIGURE 9-1: INTE RRUPT LOGIC

Note: Do not use the MOVFF instruction to modify

any of the interrupt control registers while

any interrupt is enabled. Doing so may

cause erratic microcontroller behavior.

TMR0IE

GIEH/GIE

GIEL/PEIE

Wake-up if in Low-Po wer Mode

Interrupt to CPU

Vector to Location

0008h

INT2IF

INT2IE

INT2IP

INT1IF

INT1IE

INT1IP

TMR0IF

TMR0IE

TMR0IP

INT0IF

INT0IE

RBIF

RBIE

RBIP

IPEN

TMR0IF

TMR0IP

INT1IF

INT1IE

INT1IP

INT2IF

INT2IE

INT2IP

RBIF

RBIE

RBIP

INT0IF

INT0IE

GIEL\PEIE

Interrupt to CPU

Vector to Location

IPEN

0018h

INT0IF

INT0IE

INT0IF

INT0IE

ADIF

ADIE

ADIP

RCIF

RCIE

RCIP

Additional Peripheral Interrupts

ADIF

ADIE

ADIP

High Priority Interrupt Generation

Low Priority Interrupt Generation

RCIF

RCIE

RCIP

Additional Peripheral Interrupts

GIE\GIEH

PIC18F1220/1320

9.1 INTCON Registers

The INTCON registers are readable and writable

registers, which contain various enable, priority and

flag bits.

Note: Interru pt flag bit s ar e set when an inter rupt

conditi on occurs , regardless of the sta te of

its corresponding enable bit or the global

interrupt enable bit. User software should

ensure the appropriate interrupt flag bits

are clear prior to enabling an interrupt.

This feature allows for software polling.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-x

GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF

bit 7 bit 0

bit 7 GIE/GIEH: Global Interrupt Enable bit

When IPEN = 0:

1 = Enables all unmasked interrupts

0 = Disables all interrupts

When IPEN = 1:

1 = Enables all high priority interrupts

0 = Disables all interrupts

bit 6 PEIE/GIEL: Periphera l Interr upt Enab le bit

When IPEN = 0:

1 = Enables all unmasked peripheral interrupts

0 = Disables all pe ripheral interrupts

When IPEN = 1:

1 = Enables all low priority peripheral interrupts

0 = Disables all low priority peripheral interrupts

bit 5 TMR0IE: TMR0 Overflow Interrupt Enable bit

1 = Enables the TMR0 overflow interrupt

0 = Disables the TMR0 overflow interrupt

bit 4 INT0IE: INT0 External Interrupt Enable bit

1 = Enables the INT0 external interrupt

0 = Disables the INT0 external interrupt

bit 3 RBIE: RB Port Change Interrupt Enable bit

1 = Enables the RB port change interrupt

0 = Disables the RB port change inte rrup t

bit 2 TMR0IF: TMR0 Overflow Interrupt Flag bit

1 = TMR0 re gister has overflowe d (must be cleare d in software)

0 = TMR0 re gister did no t overfl ow

bit 1 INT0IF: INT0 External Interrupt Flag bit

1 = The INT0 external interrupt occurred (must be cleared in software)

0 = The INT0 external interrupt did not occur

bit 0 RBIF: RB Port Change Interrupt Flag bit

1 = At least one of the RB7:RB4 pins changed state (must be cleared in software)

0 = None of the RB7:RB4 pins have changed state

Note: A mismatch condition will continue to set this bit. Reading PORTB will end the

mismatch condition and allow the bit to be cleared.

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

R/W-1 R/W-1 R/W-1 R/W-1 U-0 R/W-1 U-0 R/W-1

RBPU INTEDG0 INTEDG1 INTEDG2 —TMR0IP—RBIP

bit 7 bit 0

bit 7 RBPU: PORTB Pull-up Enable bit

1 = All PORTB pull-ups are disabled

0 = PORTB pull-ups are enabled by individual port latch values

bit 6 INTEDG0: External Interrupt 0 Edge Select bit

1 = Interrupt on rising edge

0 = Interrupt on falling edge

bit 5 INTEDG1: External Interrupt 1 Edge Select bit

1 = Interrupt on rising edge

0 = Interrupt on falling edge

bit 4 INTEDG2: External Interrupt 2 Edge Select bit

1 = Interrupt on rising edge

0 = Interrupt on falling edge

bit 3 Unimplemented: Read as ‘0’

bit 2 TMR0IP: TMR0 Overflow Interrupt Priority bit

1 = High priority

0 = Low priority

bit 1 Unimplemented: Read as ‘0’

bit 0 RBIP: RB Port Change Interrupt Priority bit

1 = High priority

0 = Low priority

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

Note: Interrupt flag bit s are s et whe n an i nterr upt c ond iti on oc c urs , rega rdle ss of the st a te

of its corresponding enable bit or the global interrupt enable bit. User software

should ensure the appropriate interrupt flag bits are clear prior to enabling an

interrupt. This feature allows for software polling.

PIC18F1220/1320

R/W-1 R/W-1 U-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0

INT2IP INT1IP —INT2IEINT1IE— INT2IF INT1IF

bit 7 bit 0

bit 7 INT2IP: INT2 External Interrupt Priority bit

1 = High p riority

0 = Low priority

bit 6 INT1IP: INT1 External Interrupt Priority bit

1 = High p riority

0 = Low priority

bit 5 Unimplemented: Read as ‘0’

bit 4 INT2IE: INT2 External Interrupt Enable bit

1 = Enables the INT2 external interrupt

0 = Disables the INT2 external interrupt

bit 3 INT1IE: INT1 External Interrupt Enable bit

1 = Enables the INT1 external interrupt

0 = Disables the INT1 external interrupt

bit 2 Unimplemented: Read as ‘0’

bit 1 INT2IF: INT2 External Interrupt Flag bit

1 = The INT2 external interrupt occurred (must be cleared in software)

0 = The INT2 external interrupt did not occur

bit 0 INT1IF: INT1 External Interrupt Flag bit

1 = The INT1 external interrupt occurred (must be cleared in software)

0 = The INT1 external interrupt did not occur

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

Note: Interrupt flag bit s are s et whe n an in terrupt conditi on oc curs , rega rdle ss of the st a te

of its corresponding enable bit or the global interrupt enable bit. User software

should ensure the appropriate interrupt flag bits are clear prior to enabling an

interrupt. This feature allows for software polling.

PIC18F1220/1320

9.2 PIR Registers

The PIR regi sters c onta in the ind ividual fl ag bit s for the

peripheral interrupts. Due to the number of peripheral

interrupt sources, there are two Peripheral Interrupt

Request (Flag) registers (PIR1, PIR2).

Note 1: Interrupt flag bit s are set when an interrupt

condition occurs, regardless of the state of

its corresponding enable bit or the Global

Interrupt Enable bit, GIE (INTCON<7>).

2: User software should ensure the appropri-

ate interrupt flag bits are cleared prior to

enabling an interrupt and after servicing

that interrupt.

U-0 R/W-0 R-0 R-0 U-0 R/W-0 R/W-0 R/W-0

— ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF

bit 7 bit 0

bit 7 Unimplemented: Read as ‘0’

bit 6 ADIF: A/D Converter Interrupt Flag bit

1 = An A/D conversion completed (must be cleared in software)

0 = The A/D conversion is not complete

bit 5 RCIF: EUSART Receive Interrupt Flag bit

1 = The EUSART receive buffer, RCREG, is full (cleared when RCREG is read)

0 = The EUSART receive buffer is empty

bit 4 TXIF: EUSART Transmit Interrupt Flag bit

1 = The EUSART transmit buffer, TXREG, is empty (cleared when TXREG is written)

0 = The EUSART transmit buffer is full

bit 3 Unimplemented: Read as ‘0’

bit 2 CCP1IF: CCP1 Interrupt Flag bit

Capture mode:

1 = A TMR1 register capture occurre d (must be cleared in software)

0 = No TMR1 register capture occurred

Compare mode:

1 = A TMR1 register compare match occurred (must be cleared in software)

0 = No TMR1 register compare match occurred

PWM mode:

Unused in this mode .

bit 1 TMR2IF: TMR2 to PR2 Match Interrupt Flag bit

1 = TMR2 to PR2 match occurred (must be cleared in software)

0 = No TMR2 to PR2 match occurred

bit 0 TMR1IF: TMR1 Overflow Interrupt Flag bit

1 = TMR1 register overflowed (m ust be cleared in software)

0 = TMR1 register did not overflow

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

R/W-0 U-0 U-0 R/W-0 U-0 R/W-0 R/W-0 U-0

OSCFIF —— EEIF — LVDIF TMR3IF —

bit 7 bit 0

bit 7 OSCFIF: Oscillator Fail Interrupt Flag bit

1 = System oscill ator faile d, clock input has change d to INT OSC (mu st be clea red in softwa re)

0 = System clock operating

bit 6-5 Unimplemented: Read as ‘0’

bit 4 EEIF: Data EEPROM/Flash Write Operation Interrupt Flag bit

1 = The write operation is complete (must be cleared in software)

0 = The write operation is not complete or has not been started

bit 3 Unimplemented: Read as ‘0’

bit 2 LVDIF: Low-Volt a ge D etec t Inter rupt Flag bit

1 = A low-voltage condition occurred (must be cleared in software)

0 = The device voltage is above the Low-Voltage Detect trip point

bit 1 TMR3IF: TMR3 Overflow Interrupt Flag bit

1 = TMR3 register overflowed (must be cleared in software)

0 = TMR3 register did not overflow

bit 0 Unimplemented: Read as ‘0’

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

9.3 PIE Registers

The PIE registers contain the individual enable bits for

the peripheral interrupts. Due to the number of

peripheral interrupt sources, there are two Peripheral

Interrupt Enable registers (PIE1, PIE2). When

IPEN = 0, the PEIE bit must be set to enable any of

these peripheral interrupts.

U-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0

— ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE

bit 7 bit 0

bit 7 Unimplemented: Read as ‘0’

bit 6 ADIE: A/D Converter Interrupt Enable bit

1 = Enables the A/D interrupt

0 = Disables the A/D interrupt

bit 5 RCIE: EUSART Receiv e Interru pt Enab le bit

1 = Enables the EUSART receive interrupt

0 = Disables the EUSART receive interrupt

bit 4 TXIE: EUSART Transmit Interrupt Enable bit

1 = Enables the EUSART transmit interrupt

0 = Disables the EUSART transmit interrupt

bit 3 Unimplemented: Read as ‘0’

bit 2 CCP1IE: CCP1 Interrupt Enable bit

1 = Enables the CCP1 interrupt

0 = Disables the CCP1 interrupt

bit 1 TMR2IE: TMR2 to PR2 Match Interrupt Enable bit

1 = Enables the TMR2 to PR2 match interrupt

0 = Disables the TMR2 to PR2 match interrupt

bit 0 TMR1IE: TMR1 Overflow Interrupt Enable bit

1 = Enables the TMR1 overflow interrupt

0 = Disables the TMR1 overflow interrupt

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

R/W-0 U-0 U-0 R/W-0 U-0 R/W-0 R/W-0 U-0

OSCFIE —— EEIE — LVDIE TMR3IE —

bit 7 bit 0

bit 7 OSCFIE: Oscillator Fail Interrupt Enable bit

1 = Enabled

0 =Disabled

bit 6-5 Unimplemented: Re ad as ‘0’

bit 4 EEIE: Data EEPROM/Flash Write Operation Interrupt Enable bit

1 = Enabled

0 =Disabled

bit 3 Unimplemented: Read as ‘0’

bit 2 LVDIE: Low-Voltage Detect Interrupt Enable bit

1 = Enabled

0 =Disabled

bit 1 TMR3IE: TMR3 Overflow Interrupt Enable bit

1 = Enabled

0 =Disabled

bit 0 Unimplemented: Read as ‘0’

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

9.4 IPR Registers

The IPR registers contain the individual priority bits for

the peripheral interrupts. Due to the number of

peripheral interrupt sources, there are two Peripheral

Interrupt Priority registers (IPR1, IPR2). Using the

priority bits requires that the Interrupt Priority Enable

(IPEN) bit be set.

U-0 R/W-1 R/W-1 R/W-1 U-0 R/W-1 R/W-1 R/W-1

— ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP

bit 7 bit 0

bit 7 Unimplemented: Read as ‘0’

bit 6 ADIP: A/D Converter Interrupt Priority bit

1 =High priority

0 = Low priority

bit 5 RCIP: EUSART Receive Interrupt Priority bit

1 =High priority

0 = Low priority

bit 4 TXIP: EUSART Transmit Interrupt Priority bit

1 =High priority

0 = Low priority

bit 3 Unimplemented: Read as ‘0’

bit 2 CCP1IP: CCP1 Interrupt Priority bit

1 =High priority

0 = Low priority

bit 1 TMR2IP: TMR2 to PR2 Match Interrupt Priority bit

1 =High priority

0 = Low priority

bit 0 TMR1IP: TMR1 Overflow Interrupt Priority bit

1 =High priority

0 = Low priority

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

R/W-1 U-0 U-0 R/W-1 U-0 R/W-1 R/W-1 U-0

OSCFIP —— EEIP — LVDIP TMR3IP —

bit 7 bit 0

bit 7 OSCFIP: Oscilla tor Fail Interrupt Priority bit

1 =High priority

0 = Low priority

bit 6-5 Unimplemented: Re ad as ‘0’

bit 4 EEIP: Data EEPROM/Flash Write Operation Interrupt Priority bit

1 =High priority

0 = Low priority

bit 3 Unimplemented: Read as ‘0’

bit 2 LVDIP: Low-Voltage Detect Interrupt Priority bit

1 =High priority

0 = Low priority

bit 1 TMR3IP: TMR3 Overflow Interrupt Priority bit

1 =High priority

0 = Low priority

bit 0 Unimplemented: Read as ‘0’

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

9.5 RCON Register

The RCO N register con tains bits used to determine th e

cause of the last Reset or wake-up from a low-power

mode. RCON also contains the bit that enables

interrupt priorities (IPEN).

R/W-0 U-0 U-0 R/W-1 R-1 R-1 R/W-0 R/W-0

IPEN ——RITO PD POR BOR

bit 7 bit 0

bit 7 IPEN: Interrupt Priority Enable bit

1 = Enable priority levels on interrupts

0 = Disable priority levels on interrupts (PIC16CXXX Compatibility mode)

bit 6-5 Unimplemented: Read as ‘0’

bit 4 RI: RESET Instruction Flag bit

For details of bit operation, see Register 5-3.

bit 3 TO: Watchdog Time-out Flag bit

For details of bit operation, see Register 5-3.

bit 2 PD: Power-down Detection Flag bit

For details of bit operation, see Register 5-3.

bit 1 POR: Power-on Reset Status bit

For details of bit operation, see Register 5-3.

bit 0 BOR: Brown-out Reset Status bit

For details of bit operation, see Register 5-3.

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

9.6 INTn Pin Interrupts

External interrupts on the RB0/INT0, RB1/INT1 and

RB2/INT2 pins are edge-triggered: either rising if the

corresp onding INTEDGx b it is set in the INTCON2 re g-

ister, or fall in g i f t he INTEDGx bi t i s cl ear. When a v ali d

edge appears on the RBx/INTx pin, the corresponding

flag bit, INTxF, is set. This interrupt can be disabled by

clearing the corresponding enable bit, INTxE. Flag bit,

INTxF, must be cleared in software in the Interrupt

Service Routine before re-enabling the interrupt. All

external interrupts (INT0, INT1 and INT2) can wake-up

the p roces sor fr om low -pow er mode s if b it INT xE was

set prior to going into low-power modes. If the Global

Interrupt Enable bit, GIE, is set, the processor will

branch to the interrupt vector following wake-up.

Interrupt priority for INT1 and INT2 is determined by the

value contained in the interrupt priority bits, INT1IP

(INTCON3<6>) and INT2IP (INTCON3<7>). There is

no priority bit associated with INT0. It is always a high

priority interrupt source.

9.7 TMR0 Interrupt

In 8-bit mode (which is the default), an overflow

(FFh →00h) in the TMR0 register will set flag bit,

TMR0IF. In 16-bit m ode, an overf low (FFFFh → 0000h)

in the TMR0H:TMR0L registers will set flag bit,

TMR0IF. The interrupt can be enabled/disabled by

setting/clearing enable bit, TMR0IE (INTCON<5>).

Interrupt priority for Timer0 is determined by the value

contained in the interrupt priority bit, TMR0IP

(INTCON2<2>). See Section 11.0 “Timer0 Module”

for further details on the Timer0 module.

9.8 PORTB Interrupt-on-Change

An input change on PORTB<7:4> sets flag bit, RBIF

(INTCON<0>). The interrupt can be enabled/disabled

by setting/clearing enable bit, RBIE (INTCON<3>).

Interrupt priority for PORTB interrupt-on-change is

determined by the value contained in the interrupt

priority bit, RBIP (INTCON2<0>).

9.9 Context Saving During Interrupt s

During interrupts, the return PC address i s saved on the

stack. Additional ly , the WREG, S tatus and BSR registers

are saved on the fast return stack. If a fast return from

interrupt is not used (see Section 5.3 “Fast Register

Stack”), the user may need to save the WREG, Status

and BSR registers on entry to the Interrupt Service

Routine. Depending on the user’s application, other

registers may also need to be saved. Example 9-1

saves and restores the WREG, Status and BSR

registers during an Interrupt Service Routine.

EXAMPLE 9-1: SAVING STATUS, WREG AND BSR REGISTERS IN RAM

MOVWF W_TEMP ; W_TEMP is in virtual bank

MOVFF STATUS, STATUS_TEMP ; STATUS_TEMP located anywhere

MOVFF BSR, BSR_TEMP ; BSR_TMEP located anywhere

;

; USER ISR CODE

;

MOVFF BSR_TEMP, BSR ; Restore BSR

MOVF W_TEMP, W ; Restore WREG

MOVFF STATUS_TEMP, STATUS ; Restore STATUS

PIC18F1220/1320

NOTES:

PIC18F1220/1320

10.0 I/O PORTS

Depending on the device selected and features

enabled, there are up to five ports available. Some pins

of the I/O ports are multiplexed with an alternate

function from the peripheral features on the device. In

general, when a perip heral is ena bled, that pi n may not

be used as a general purpose I/O pin.

Each port has three registers for its operation. These

registers are:

• TRIS register (data direction register)

• POR T register (rea ds the lev els on the pin s of the

device)

• LAT register (output latch)

The Data Latch (LATA) register is useful for read-

modify-write operations on the value that the I/O pins

are driving.

A simplified model of a generic I/O port without the

interf aces to o ther peripheral s i s sho w n in Fi gure 10-1.

FIGURE 10-1: GENERIC I/O PORT

OPERATION

10.1 PORTA, TRISA and LATA

Registers

PORTA is an 8-bit wide, bidirectional port. The corre-

sponding data direction register is TRISA. Setting a

TRISA bit (= 1) will make the corresponding PORTA pin

an input (i.e., put the corresponding output driver in a

high-impedance mode). Clearing a TRISA bit (= 0) wi ll

make the correspon ding POR TA pin an output (i.e., put

the contents of the output latch on the selected pin).

Reading the PORTA register reads the status of the

pins, whereas writing to it will write to the port latch.

The Data Latch register (LATA) is also memory

mapped. Read-modify-write operations on the LATA

PORTA.

The RA4 pin is multiplexed with the Timer0 module

clock input to become the RA4/T 0CKI pin.

The sixth pin of PORTA (MCLR/VPP/RA5) is an input

only pin. Its operation is controlled by the MCLRE

configuration bit in Configuration Register 3H

(CONFIG3H<7>). When selected as a port pin

(MCLRE = 0), it functions as a digital input on ly pin; as

such, i t does not have TRIS or LAT bits a ssociated w ith

its operation. Otherwise, it functions as the device’s

Master Clear input. In either configuration, RA5 also

functions as the programming voltage input during

programming.

Pins RA6 and RA7 are multi plexe d with the ma in osci l-

lator pins; they are enabled as oscillator or I/O pins by

the selection of the main oscillator in Configuration

for d etail s). W hen they are not us ed as por t pi ns, R A6

and RA7 and their associated TRIS and LAT bits are

read as ‘0’.

The other PORTA pins are multiplexed with analog

input s, th e analo g V REF+ and V REF- input s and the L VD

input. The op eration of pin s RA3:RA0 as A/D con verter

inputs is selected by clearing/setting the control bits in

the ADCON1 register (A/D Control Register 1).

The RA4/T0CKI pin is a Schmitt Trigger input and an

open-drain output. All other PORTA pins have TTL

input levels and full CMOS output drivers.

The TRISA register controls the direction of the RA

pins, ev en w he n th ey a re being used as ana log inputs .

The user mu st ensure the bit s in the TRISA registe r are

maintained set when using them as analog inputs.

EXAMPLE 10-1: INITIALIZING PORTA

Data

Bus

WR LAT

WR TRIS

RD Port

Data Latch

TRIS Latch

RD TRIS

Input

Buffer

I/O pin(1)

RD LAT

or Port

Note 1: I/O pins have diode protection to VDD and VSS.

Note: On a Power-on Reset, RA5 is enabled as a

digital input only if Master Clear functionality

is disabled.

Note: On a Power-on Reset, RA3:RA0 are

configured as analog inputs and read as

‘0’. RA 4 is always a digital pin .

CLRF PORTA ; Initialize PORTA by

; clearing output

; data latches

CLRF LATA ; Alternate method

; to clear output

; data latches

MOVLW 0x7F ; Configure A/D

MOVWF ADCON1 ; for digital inputs

MOVLW 0xD0 ; Value used to

; initialize data

; direction

MOVWF TRISA ; Set RA<3:0> as outputs

; RA<7:4> as inputs

PIC18F1220/1320

FIGURE 10-2: BLOCK DIAGRAM OF

RA3:RA0 PINS

FIGURE 10-3: BLOCK DIAGRAM OF

OSC2/CLKO/RA6 PIN

FIGURE 10-4: BLOCK DIAGRAM OF

RA4/T0CKI PIN

FIGURE 10-5: BLOCK DIAGRAM OF

OSC1/CLKI/RA7 PIN

Data

Bus

WR LATA

WR TRISA

Data Latch

TRIS Latch

RD TRISA

RD PORTA

VSS

VDD

I/O pin(1)

Note 1: I/O pins have protection diodes to VDD and VSS.

Analog

Input

Mode

To A/D Converter and LVD Modules

RD LATA

PORTA

Schmitt

Trigger

Input

Buffer

Data

Bus

WR LAT A

Data Latch

TRIS Latch

RD PORTA

VSS

VDD

I/O pin(1)

Note 1: I/O pins have protection diodes to VDD and VSS.

PORTA

RD LAT A

RA6 Enable

ECIO or

Enable

RCIO

TRISA

Schmitt

Trigger

Input

Buffer

Data

Bus

WR TRISA

RD PORTA

Data Latch

TRIS Latch

Schmitt

Trigger

Input

Buffer

VSS

I/O pin(1)

TMR0 Clock Input

RD LATA

WR LATA

PORTA

Note 1: I/O pins have protection diodes to VDD and VSS.

RD TRISA

Data

Bus

WR LATA

Data Latch

TRIS Latch

RD PORTA

VSS

VDD

I/O pin(1)

Note 1: I/O pins have protection diodes to VDD and VSS.

PORTA

RD LATA

Enable

RA7

TRISA

RA7 Enab le To Oscillator

Schmitt

Trigger

Input

Buffer

PIC18F1220/1320

FIGURE 10-6: MCLR/VPP/RA5 PIN BLOCK DIAGRAM

TABLE 10-1: PORTA FUNCTIONS

TABLE 10-2: SUMMARY OF REGISTERS ASSOCIATED WITH PORTA

MCLR/VPP/RA5

Data Bus

RD PORTA

RD LATA

Schmitt

Trigger

MCLRE

RD TRISA

Latch

Filter Low-Level

MCLR Detect

High-Voltage Detect

Internal M C LR

Name Bit# Buffer Function

RA0/AN0 bi t 0 ST Input/output port pin or analog input.

RA1/AN1/LVDIN bit 1 ST Input/output port pin, analog input or Low-Voltage Detect input.

RA2/AN2/VREF- bit 2 ST Input/output port pin, analog input or VREF-.

RA3/AN3/VREF+ bit 3 ST Input/output port pin, analog input or VREF+.

RA4/T0CKI bit 4 ST Input/output port pin or external clock input for Timer0.

Output is open-drain type.

MCLR/VPP/RA5 bit 5 ST Master Clear inp ut or p r ogra mmin g vo lt a ge input (if MCLR is e nabled); input

only port pin or programming voltage input (if MCLR is disabled).

OSC2/CLKO/RA6 bit 6 ST OSC2, clock output or I/O pin.

OSC1/CLKI/RA7 bit 7 ST OSC1, clock input or I/O pin.

Legend: TTL = TTL input, ST = Schmitt T rig ge r input

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on

POR, BOR

Value on

all other

Resets

PORTA RA7(1) RA6(1) RA5(2) RA4 RA3 RA2 RA1 RA0 xx0x 0000 uu0u 0000

LATA LATA7(1) LATA6(1) — LATA Data Output Register xx-x xxxx uu-u uuuu

TRISA TRISA7(1) TRISA6(1) — PORTA Data Direction Register 11-1 1111 11-1 1111

ADCON1 — PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 -000 0000 -000 0000

Legend: x = unknown, u = unchanged, – = unimplemented locations read as ‘0’. Shad ed cell s are not u sed by P OR TA.

Note 1: RA7:RA6 and their associated latch and data direction bits are enabled as I/O pins based on oscillator

configuration; otherwise, they are read as ‘0’.

2: RA5 is an input only if MCLR is disabled.

PIC18F1220/1320

10.2 PORTB, TRISB and LATB

Registers

PORTB is an 8-bit wide, bidirectional port. The corre-

sponding data direction register is TRISB. Setting a

TRISB bit (= 1) will make the corresponding PORTB

pin an input (i.e., put the corresponding output driver in

a high-impedance mode). Clearing a TRISB bit (= 0)

will make th e corresp onding POR TB pi n an out put (i.e .,

put the contents of the output latch on the selected pin).

The Data Latch register (LATB) is also memory

mapped. Read-modify-write operations on the LATB

PORTB.

EXAMPLE 10-2: INITIALIZI NG PORTB

Pins RB0-RB2 are multiplexed with INT0-INT2; pins

RB0, RB1 and RB4 are multiplexed with A/D inputs;

pins RB1 and RB4 are multiplexed with EUSART; and

pins RB2, RB3, RB6 and RB7 are multiplexed with

ECCP.

Each of th e POR TB pins has a we ak inte rnal pul l-up. A

single control bit can turn on all the pull-ups. This is

performed by clearing bit, RBPU (INTCON2<7>). The

weak pull-up is automatically turned off when the port

pin is configured as an output. The pull-ups are

disabled on a Power-on Reset.

Four of the PORTB pins (RB7:RB4) have an interrupt-

on-change feature. Only pins configured as inputs can

cause this interrupt to occur (i.e., any RB7:RB4 pin

configured as an output is excluded from the interrupt-

on-change comparison). The input pins (of RB7:RB4)

are compared with the old value latched on the last

read of PORTB. The “mismatch” outputs of RB7:RB4

are OR’ed together to generate the RB Port Change

Interrupt with Flag bit, RBIF (INTCON<0>).

This interrupt can wake the device from Sleep. The

user, in the Interrupt Service Routine, can clear the

interrupt in the following manner:

a) Any read or write of PORTB (except with the

MOVFF instruction). This will end the mismatch

condition.

b) Clear flag bit, RBIF.

A mismatc h condit ion wil l contin ue to set flag bit , RBIF.

Reading PORTB will end the mismatch condition and

allow flag bit, RBIF, to be cleared.

The interrupt-on-change feature is recommended for

wake-up on key depression operation and operations

where PORTB is only used for the interrupt-on-change

feature. Polling of PORTB is not recommended while

using the interrupt-on-change feature.

FIGURE 10-7: BLOCK DIAGRAM OF

RB0/AN4/INT0 PIN

Note: On a Power-on Reset, RB4:RB0 are

configu red as analog inp uts by defau lt and

read as ‘0’; RB7:RB5 are configured as

digital inputs.

CLRF PORTB ; Initialize PORTB by

; clearing output

; data latches

CLRF LATB ; Alternate method

; to clear output

; data latches

MOVLW 0x70 ; Set RB0, RB1, RB4 as

MOVWF ADCON1 ; digital I/O pins

MOVLW 0xCF ; Value used to

; initialize data

; direction

MOVWF TRISB ; Set RB<3:0> as inputs

; RB<5:4> as outputs

; RB<7:6> as inputs

Data Latch

RBPU(2) P

VDD

Data Bus

WR LATB

WR TRISB

RD TRISB

RD PORTB

Weak

Pull-up

INTx

I/O

pin(1)

Schmitt Trigger

Buffer

TRIS Latch

RD LATB

or PORTB

Note 1: I/O pins have diode protection to VDD and VSS.

2: To enable weak pull-ups, set the appropriate TRIS

bit(s) and clear the RBPU bit (INTCON2<7>).

To A/D Converter

Analog Input Mode

TTL

Input

Buffer

PIC18F1220/1320

FIGURE 10-8: BLOCK DIAGRAM OF RB1/AN5/TX/CK/INT1 PIN

Data Latch

RBPU(2) P

VDD

Data Bus

WR LATB

WR TRISB

RD TRISB

RD PORTB

Weak

Pull-up

RD PORTB

RB1 pin(1)

TRIS Latch

RD LATB

PORTB

Note 1: I/O pins have diode protection to VDD and VSS.

2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (INTCON2<7>).

To A/D Converter

INT1/CK Input

Analog Input

Mode

TX/CK Data

EUSART Enable

Schmitt

Trigger

Input

Buffer

TX/CK TRIS

Analog Input Mode

TTL

Input

Buffer

PIC18F1220/1320

FIGURE 10-9: BLOCK DIAGRAM OF RB2/P1B/INT2 PIN

Data Latch

RBPU(2) P

VDD

Data Bus

WR LATB or

WR TRISB

RD TRISB

RD PORTB

Weak

Pull-up

RD PORTB

RB2 pin (1)

TTL

Input

Buffer

TRIS Latch

RD LATB

PORTB

P1B Data

Note 1: I/O pins have diode protection to VDD and VSS.

2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (INTCON2<7>).

P1B Enable

INT2 Input Schmitt

Trigger

P1B/D Tri-State

Auto-Shutdown

PIC18F1220/1320

FIGURE 10-10: BLOCK DIAGRAM OF RB3/CCP1/P1A PIN

Data Bus

WR LATB or

WR TRISB

Data Latch

TRIS Latch

RD TRISB

ECCP1/P1A Data Out 1

VDD

VSS

RD PORTB

ECCP1 Inpu t

RB3 pin

PORTB

RD LATB

Schmitt

Trigger

VDD

Weak

Pull-up

RBPU(2)

TTL Inp ut

Buffer

Note 1: I/O pins have diode protection to VDD and VSS.

2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (INTCON2<7>).

3: ECCP1 pin output enable active for any PWM mode and Compare mode, where CCP1M<3:0> = 1000 or 1001.

4: ECCP1 pin input enable active for Capture mode only.

ECCP1(3) pin Output Enable

P1A/C Tri-State Auto-Shutdown

ECCP1(4) pin Input Enable

PIC18F1220/1320

FIGURE 10-11: BLOCK DIAGRAM OF RB4/AN6/RX/DT/KBI0 PIN

Data Bus

WR LATB or

WR TRISB

Data Latch

TRIS Latch

RD TRISB

DT Data

RD PORTB

RB4 pin

PORTB

RD LATB

RBPU(2)

PWeak

Pull-up

From other QD

Set RBIF

RB7:RB4 pins RD PORTB

To A/D Converter

EUSART Enabled

TTL

Input

Buffer

Note 1: I/O pins have diode protection to VDD and VSS.

2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (INTCON2<7>).

DT TRIS

Analog Input Mode

RX/DT Input

Analog Input

Mode

Schmitt

Trigger

VDD

PIC18F1220/1320

FIGURE 10-12: BLOCK DIAGRAM OF RB5/PGM/KBI1 PIN

Data Latch

From other

RBPU(2) P

VDD

I/O pin (1)

Data Bus

WR LATB

WR TRISB

Set RBIF

TRIS Latch

RD TRISB

RD PORTB

RB7:RB5 and

Weak

Pull-up

RD PORTB

Latch

TTL

Input

Buffer ST

Buffer

RB7:RB5 in Serial Programming Mode

RD LATB

or PORTB

Note 1: I/O pins have diode protection to VDD and VSS.

2: To enable weak pull-ups, set the ap propriate TRIS bit(s) and clear the RBPU bit

(INTCON2<7>).

RB4 pins

PIC18F1220/1320

FIGURE 10-13: BLOCK DIAGRAM OF RB6/PGC/T1OSO/T13CKI/P1C/KBI2 PIN

Data Bus

WR LATB or

WR TRISB

Data Latch

TRIS Latch

RD TRISB

P1C Data

RD PORTB

RB6 p i n

PORTB

RD LATB

Schmitt

Trigger

RBPU(2) PWeak

Pull-up

From other QD

Set RBIF

RB7:RB4 pi ns RD PORTB

PGC

From RB7 pin

Timer1

Oscillator

T1OSCEN

T13CKI

Note 1: I/O pins have diode protec tion to VDD and VSS.

2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (INTCON2<7>).

TTL

Buffer

ECCP1 P1C/D Enable

P1B/D Tri-State Auto-Shutdown

VDD

PIC18F1220/1320

FIGURE 10-14: BLOCK DIAGRAM OF RB7/PGD/T1OSI/P1D/KBI3 PIN

Data Bus

WR LATB or

WR TRISB

Data Latch

TRIS Latch

RD TRISB

P1D Data

RD PORTB

RB7 pin

PORTB

RD LATB

Schmitt

Trigger

To RB6 pin

RBPU(2) PWeak

Pull-up

From other QD

Set RBIF

RB7:RB4 pins RD PORTB

PGD

ECCP1 P1C/D Enable

TTL

Input

Buffer

Note 1: I/O pins have diode protection to VDD and VSS.

2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (INTCON2<7>).

P1B/D Tri-State Auto-Shutdown

T1OSCEN

VDD

PIC18F1220/1320

TABLE 10-3: PORTB FUNCTIONS

TABLE 10-4: SUMMARY OF REGISTERS ASSOCIATED WITH PORTB

Name Bit# Buffer Function

RB0/AN4/INT0 b it 0 TTL(1)/ST(2) Input/output port pin, analog input or external interrupt

input 0.

RB1/AN5/TX/CK/INT1 bit 1 TTL(1)/ST(2) Input/output port pin, analog input, Enhanced USART

Asynchronous Transmit, Addressable USART

Synchronou s Clock or external interru pt input 1.

RB2/P1B/INT2 bit 2 TTL(1)/ST(2) Input/output port pin or exter nal interru pt input 2.

Internal software programmable weak pull-up.

RB3/CCP1/P1A bit 3 TTL(1)/ST(3) Input/out put port pin or Capture1 input/Compare1 output/

PWM output. Internal software programmable weak pull-up.

RB4/AN6/RX/DT/KBI0 bit 4 TTL(1)/ST(4) Input/output port pin (with interrupt-on-change), analog input,

Enhanced USART Asynchronous Receive or Addressable

USART Synchronous Data.

RB5/PGM/KBI1 bit 5 TTL(1)/ST(5) Input/output port pin (with interrupt-on-change).

Internal software programmable weak pull-up.

Low-Voltage ICSP enable pin.

RB6/PGC/T1OSO/T13CKI/

P1C/KBI2 bit 6 TTL(1)/ST(5,6) Input/output port pin (with interrupt-on-change), Timer1/

Timer3 clock input or Timer1oscillator output.

Internal software programmable weak pull-up.

Serial program mi ng cl ock .

RB7/PGD/T1OSI/P1D/KBI3 bit 7 TTL(1)/ST(5) Input/output port pin (with interrupt-on-change) or Timer1

oscilla tor input. In ternal sof tware prog rammable w eak pull- up.

Serial program mi ng data.

Legend: TTL = TTL input, ST = Schmitt T rig ge r input

Note 1: This buffer is a TTL input when configured as a port input pin.

2: This buffer is a Schmitt Trigger input when configured as the external interrupt.

3: This buffer is a Schmitt Trigger input when configured as the CCP1 input.

4: This buffer is a Schmitt Trigger input when used as EUSART receive input.

5: This buffer is a Schmitt Trigger input when used in Serial Programming mode.

6: This buffer is a TTL input when used as the T13CKI input.

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on

POR, BOR

Value on

all other

Resets

PORTB RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 xxxq qqqq uuuu uuuu

LATB LATB Data Output Register xxxx xxxx uuuu uuuu

TRISB PORTB Data Direction Register 1111 1111 1111 1111

INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u

INTCON2 RBPU INTEDG0 INTEDG1 INTEDG2 —TMR0IP —RBIP1111 -1-1 1111 -1-1

INTCON3 INT2IP INT1IP — INT2IE INT1IE — INT2IF INT1IF 11-0 0-00 11-0 0-00

ADCON1 — PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 -000 0000 -000 0000

Legend: x = unknown, u = unchanged, q = value depends on condition. Shaded cells are not used by PORTB.

PIC18F1220/1320

11.0 TIMER0 MODULE

The Timer0 module has the following features:

• Software selectable as an 8-bit or 16-bit timer/

counter

• Readable and writable

• Dedicated 8-bit software programmable prescaler

• Clock source selectable to be external or internal

• Interrupt-on-overflow from FFh to 00h in 8-bit

mode and FFFFh to 0000h in 16-bit mode

• Edge select for external clock

Figure 11-1 shows a simplified block diagram of the

Timer0 module in 8-bit mode and Figure 11-2 shows a

simplified block diagram of the Timer0 module in 16-bit

mode.

The T0CON register (Register 11-1) is a readable and

writ able registe r th at co ntro ls al l the aspec t s o f Ti mer 0,

including the prescale selection.

R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1

TMR0ON T08BIT T0CS T0SE PSA T0PS2 T0PS1 T0PS0

bit 7 bit 0

bit 7 TMR0ON: Timer0 On/Off Control bit

1 = Enables Timer 0

0 = Stops Timer0

bit 6 T08BIT: Timer0 8-bit/16-bit Control bit

1 = Timer0 is configured as an 8-bit timer/counter

0 = Timer0 is configured as a 16-bit timer/counter

bit 5 T0CS: Timer0 Clock Sour ce Select bit

1 = Transition on T0CKI pin

0 = Internal instruction cycle clock (CLKO)

bit 4 T0SE: Timer0 Source Edge Select bit

1 = Increment on high-to-low transition on T0CKI pin

0 = Increment on low-to-high transition on T0CKI pin

bit 3 PSA: Timer0 Prescaler Assignment bit

1 = TImer0 prescaler is NOT assigned. Timer0 clock input bypasses prescaler.

0 = Timer0 prescaler is assigned. Timer0 clock input comes from prescaler output.

bit 2-0 T0PS2:T0PS0: Timer0 Prescaler Select bits

111 = 1:256 Prescale value

110 = 1:128 Prescale value

101 = 1:64 Prescale value

100 = 1:32 Prescale value

011 = 1:16 Prescale value

010 = 1:8 Prescale value

001 = 1:4 Prescale value

000 = 1:2 Prescale value

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

FIGURE 11-1: TIMER0 BLOCK DIAGRAM IN 8-BIT MODE

FIGURE 11-2: TIMER0 BLOCK DIAGRAM IN 16-BIT MODE

Note: Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI maximum prescale.

RA4/T0CKI

T0SE

T0CS

FOSC/4

Programmable

Prescaler

Sync with

Internal

Clocks TMR0

(2 TCY Delay)

Data Bus

PSA

T0PS2, T0PS1, T0PS0 Set Interr upt

Flag bit TMR0IF

on Overflow

Note: Upon Reset, Timer0 is enabled in 8-bit mode with clock input from T0CKI maximum prescale.

T0SE

T0CS

FOSC/4

Programmable

Prescaler

Sync with

Internal

Clocks TMR0L

(2 TCY Delay)

Data Bus<7:0>

PSA

T0PS2, T0PS1, T0PS0

Set Interr upt

Flag bit TMR0IF

on Overflow

TMR0

TMR0H

High Byte

Read TMR0L

Write TMR0L

RA4/T0CKI

PIC18F1220/1320

11.1 Timer0 O p e r at io n

Timer0 can operate as a timer or as a counter.

Timer mode is selected by clearing the T0CS bit. In

Timer mode, the Timer0 module will increment every

instruc tion cy cle (with out pr escal er). If the TMR0 regis-

ter is w ritten , the i ncrem ent is inhi bited f or the follow ing

two instruction cycles. The user can work around this

by writing an adjusted value to the TMR0 register.

Counter mode is selected by setting the T0CS bit. In

Counter mode, Timer0 will increment either on every

rising or fal ling edge of pi n RA4/T0CKI . The increme nt-

ing edge is determined by the Timer0 Source Edge

Select bit (T0SE). Clearing the T0SE bit selects the

rising edge.

When an external cl ock input i s used for T ime r0, it must

meet certain requirements. The requirements ensure

the external clock can be synchronized with the int ernal

phase clock (TOSC). Also, th ere is a delay in the actual

incrementing of Timer0 after synchronization.

11.2 Prescaler

An 8-bi t counter i s availabl e as a presc aler for the T imer0

modul e. Th e pre sc a le r i s no t re ad able or w ri t able.

The PSA and T0PS2:T0PS0 bits determine the

prescaler assignment and prescale ratio.

Clearing b it PSA will assign the prescaler to the Timer0

module. When the prescaler is assigned to the Timer0

module, prescale values of 1:2, 1:4, ..., 1:256 are

selectable.

When assigned to the Timer0 module, all instructions

writing to the TMR0 register (e.g., CLRF TMR0, MOVWF

TMR0, BSF TMR0, x, ..., etc.) will clear the prescaler

count.

11.2.1 SWITCHI NG PRESC ALER

ASSIGNMENT

The prescaler assignment is fully under software

control (i.e., it can be changed “on-the-fly” during

program executi on).

11.3 Timer0 Int e rr u p t

The TMR0 interrupt is generated when the TMR0 reg-

ister overfl ows from FFh to 00h in 8-bit mod e, or FFFFh

to 0000h i n 16-bit mode. This overflow sets the TMR0IF

bit. The interrupt can be masked by clearing the

TMR0IE bit. The TMR0IF bit must be cleared in soft-

ware by the Timer0 module Interrupt Service Routine

before re-enabling this interrupt. The TMR0 interrupt

cannot awaken the processor from Low-Power Sleep

mode, sin ce the tim er require s clock cy cles ev en whe n

T0CS is set.

11.4 16-Bit Mode Timer Reads

and Writes

TMR0H is not the high byte of the timer/counter in

16-bit mode, but is actually a buffered version of the

high byte of T imer0 (refer to Figure 1 1-2). The high byte

of the Timer0 counter/timer is not directly readable nor

writable. TMR0H is updated with the contents of the

high byte of Timer0 during a read of TMR0L. This pro-

vides the ability to read all 16 bits of Timer0, without

having to verify that the read of the high and low byte

were valid due to a rollover between successive reads

of the high and low byte.

A write to the high byte of Timer0 must also take place

through th e TMR0H Buf fer reg ister. T ime r0 high byte i s

updated with the contents of TMR0H when a write

occurs to TMR0L. Th is allows all 1 6 bits of T imer0 to be

updated at onc e.

TABLE 11-1: REGISTERS ASSOCIATED WITH TIMER0

Note: Writing to TMR0 when the prescaler is

assign ed to Timer0 will clear th e pr escal er

count, but will not change the prescaler

assignment.

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on

POR, BOR

Value on

all othe r

Resets

TMR0L Timer0 Module Low Byte Register xxxx xxxx uuuu uuuu

TMR0H Timer0 Module High Byte Register 0000 0000 0000 0000

INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u

T0CON TMR0ON T08BIT T0CS T0SE PSA T0PS2 T0PS1 T0PS0 1111 1111 1111 1111

TRISA RA7(1) RA6(1) — PORTA Data Direction Register 11-1 1111 11-1 1111

Legend: x = unknown, u = unchanged, – = unimplemented locations read as ‘0’. Shaded cells are not used by Timer0.

Note 1: RA6 and RA7 are enabled as I/O pins, depending on the oscillator mode selected in Configuration Word 1H.

PIC18F1220/1320

NOTES:

PIC18F1220/1320

12.0 TIMER1 MODULE

The Timer1 module timer/counter has the following

features:

• 16-bit timer/counter

(two 8-bit registers: TMR1H and TMR1L)

• Readable and writable (both registers)

• Internal or external clock select

• Interrupt-on-overflow from FFFFh to 0000h

• Reset from CCP module special event trigger

• Status of system clock operation

Figure 12-1 is a simplified block diagram of the Timer1

module.

module and contains the Timer1 Oscillator Enable bit

(T1OSCEN). Timer1 can be enabled or disabled by

setting or clearing control bit, TMR1ON (T1CON<0>).

The T imer1 oscillator can be used as a secondary clock

source in power managed modes. When the T1RUN bit

is set, the Timer1 oscillator is providing the system

clock . If the Fail-Safe Cloc k Monitor is en abled and the

T i mer1 os cilla tor fails whil e provi ding th e syst em clo ck,

polling the T1RUN bit will indicate whether the clock is

being provided by the Timer1 oscillator or another

source.

Timer1 can also be used to provide Real-Time Clock

(RTC) functionality to applications, with only a minimal

addition of external components and code overhead.

R/W-0 R-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

RD16 T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON

bit 7 bit 0

bit 7 RD16: 16 -bit Read /Write Mode Enab le bit

1 = Enables register read/write of TImer1 in one 16-bit operation

0 = Enables register read/write of Timer1 in two 8-bit operations

bit 6 T1RUN: Timer1 System Clock Status bit

1 = System clock is derived from Timer1 oscillator

0 = System c lock is derived from another so urce

bit 5-4 T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits

11 = 1:8 Prescale value

10 = 1:4 Prescale value

01 = 1:2 Prescale value

00 = 1:1 Prescale value

bit 3 T1OSCEN: T im er1 Os ci lla tor Enab le bit

1 = Timer1 oscillator is enabled

0 = Timer1 oscillator is shut off

The oscillator inverter and feedback resistor are turned off to eliminate power drain.

bit 2 T1SYNC: Timer1 External Clock Input Synchronization Select bit

When TMR1CS = 1:

1 = Do not synchronize external clock input

0 = Synchronize external clock input

When TMR1CS = 0:

This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0.

bit 1 TMR1CS: Timer1 Clock Source Select bit

1 = External clock from pin RB6/PGC /T1OSO/T13CKI/P1C/KBI2 (on the rising ed ge)

0 = Internal clock (Fosc/ 4)

bit 0 TMR1ON: Timer1 On bit

1 = Enables Timer1

0 = Stops Timer1

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

12.1 Timer1 Operation

Timer1 can operate in one of these modes:

•As a timer

• As a synchronous counter

• As an asynchronous counter

The operating mode is determined by the clock select

bit, TMR1CS (T1CON<1>).

When TMR1CS = 0, Timer1 increments every instruc-

tion cycle. When TMR1CS = 1, Timer 1 increm ents on

every rising edge of the external clock input, or the

Timer1 oscillator, if enabled.

When the Timer1 oscillator is enabled (T1OSCEN is

set), the RB 7/PGD/T1OSI/P1D/KBI3 a nd RB6/T1O SO/

T13CKI/P1C/KBI2 pins become inputs. That is, the

TRISB7:TRISB6 values are ignored and the pins read

as ‘0’.

Timer1 also has an internal “Reset input”. This Reset

can be generated by the CCP module (see

Section 15.4.4 “Special Event Trigger”).

FIGURE 12-1: TIMER1 BLOCK DIAGRAM

FIGURE 12-2: TIMER1 BLOCK DIAGRAM: 16-BIT READ/WRITE MODE

TMR1H TMR1L

T1SYNC

TMR1CS

T1CKPS1:T1CKPS0 Peripheral Clocks

FOSC/4

Internal

Clock

TMR1ON

On/Off

Prescaler

1, 2, 4, 8 Synchronize

det

Synchronized

Clock Input

TMR1IF

Overflow TMR1 CLR

CCP Special Event Trigger

T1OSCEN

Enable

Oscillator(1)

T1OSC

Interrupt

Flag bit

Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off. This eliminates

power drain.

T1OSI

T13CKI/T1OSO

Timer 1 TMR1L

T1OSC T1SYNC

TMR1CS

T1CKPS1:T1CKPS0

Peripheral Clocks

T1OSCEN

Enable

Oscillator(1)

TMR1IF

Overflow

Interrupt

FOSC/4

Internal

Clock

TMR1ON

on/off

Prescaler

1, 2, 4, 8 Synchronize

det

Synchronized

Clock Input

T13CKI/T1OSO

T1OSI

TMR1

Flag bit

Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off. This eliminates power drain.

High Byte

Data Bus<7:0>

TMR1H 8

Read TMR1L

Write TMR1L

CLR

CCP Special Event Trigger

PIC18F1220/1320

12.2 Timer1 Oscillator

A crystal oscillator circuit is built-in between pins T1OSI

(input) and T1OSO (amplifier output). It is enabled by

setting control bit, T1OSCEN (T1CON<3>). The oscil-

lator is a low-powe r os ci ll ator rated for 32 kHz cry stals.

It will c ontinue to run durin g all power manage d modes.

The circuit for a typical LP oscillator is shown in

Figure 12-3. Table 12-1 shows the capacitor selection

for the Timer1 oscillator.

The user m us t pro vi de a sof tware time delay to ensure

proper start-up of the Timer1 oscillator.

FIGURE 12-3: EXTERNAL

COMPONENTS FOR THE

TI MER1 LP OSCILLATOR

T ABLE 12-1: CAPACITOR SELECTION FOR

THE TIMER OSCILLATOR

Note: The Timer1 oscillator shares the T1OSI

and T1OSO pins with the PGD and PGC

pins used for programming and

debugging.

When using the Timer1 oscillator, In-Circuit

Serial Programming (ICSP) may not

function correctly (high voltage or low

voltage), or the In-Circuit Debugger (ICD)

may not communicate with the controller.

As a result of using either ICSP or ICD, the

Timer1 cryst al m ay be dam aged.

If ICSP or ICD operatio ns are requi red, the

crystal should be disconnected from the

circuit (disconne ct either lead ), or insta lled

after programming. The oscillator loading

capacitors may remain in-circuit during

ICSP or ICD operation.

Osc Type Freq C1 C2

LP 32 kHz 22 pF(1) 22 pF(1)

Note 1: Microchip suggests this value as a starting

point in validating the oscillator circuit.

Oscillat or operation should then be tested

to ensure expected performance under

all expected conditions (VDD and

temperature).

2: Higher capacit ance inc reases the st abilit y

of the oscillator, but also increases the

start-up time.

3: Since each resonator/crystal has its own

characteristics, the user should consult

the resonator/crystal manufacturer for

appropriate values of external

components.

4: Capacitor values are for design guidance

only.

Note: See the Notes with Table 12-1 for additional

information about capacitor selection.

XTAL

PIC18FXXXX

PGD/T1OSI

PGC/T1OSO

32.768 kHz

22 pF

PGD

PGC

PIC18F1220/1320

12.3 Timer1 Oscillator Layout

Considerations

The Timer1 oscillator circuit draws very little power

during operation. Due to the low-power nature of the

oscillator, it may also be sensitive to rapidly changing

signals in close proximity.

The oscillator circuit, shown in Figure 12-3, should be

located as close as possible to the microcontroller.

There should be no circuits passing within the oscillator

circuit boundaries other than VSS or VDD.

If a hig h-s pee d cir cui t m us t b e loc ate d near the oscilla-

tor (such as the CCP1 pin in output compare or PWM

mode, or the primary oscillator using the OSC2 pin), a

grounded guard ring around the oscillator circuit, as

shown in Figure 12-4, may be helpful when used on a

single sided PCB, or in addition to a ground plane.

FIGURE 12-4: OSCILLATOR CIRCUIT

WITH GROUNDED

GUARD RING

12.4 Timer1 Interrupt

The TMR1 register pair (TMR1H:TMR1L) increments

from 0000h to FFFFh and rolls over to 0000h. The

Timer1 interrupt, if enabled, is generated on overflow,

which is latched in interrupt flag bit, TMR1IF

(PIR1<0>). This interrupt can be enabled/disabled by

setting/clearing Timer1 Interrupt Enable bit, TMR1IE

(PIE1<0>).

12.5 Resetting Ti me r1 Using a CCP

Trigger Output

If the CCP module is configured in Compare mode

to generate a “special event trigger”

(CCP1M3:CCP1M0 = 1011), this signal will reset

Timer1 an d start an A/D conversion , if the A/D mod-

ule is enabled (see Section 15.4.4 “Special Event

Trigger” for more infor mation).

T imer 1 must be c onfigured fo r either T ime r or Synch ro-

nized Counter mode to take advantage of this feature.

If Timer1 is running in Asynchronous Counter mode,

this Reset operation may not work.

In the event that a write to Timer1 coincides with a

special event trigger from CCP1, the write will take

precedence.

In this mode of o peration, the CCPR1H:CCPR1L regis-

ter pair effectively becomes the period register for

Timer1.

12.6 Timer1 16-Bit Read/Write Mode

Timer1 can be configured for 16-bit reads and writes

(see Figure 12-2). When the RD16 control bit

(T1CON< 7>) is s et, the a ddress for TM R1H is mappe d

to a buffer regis ter f or th e hig h byte of Timer 1. A r ead

from TMR1L will load the contents of the high byte of

Timer1 into the Timer1 high byte buffer. This provides

the user with the ability to accurately read all 16 bits of

Timer1 without having to determine whether a read of

the high byte, followed by a read of the low byte, is

valid, due to a rollover between reads.

A write to the high byte of Timer1 must also take place

through th e TMR1H Buf fer reg ister. T ime r1 high byte i s

updated with the contents of TMR1H when a write

occurs to TMR 1L . Thi s a ll ows a us er to write all 16 bits

to both the high and low bytes of Timer1 at once.

The high byte of Timer1 is not directly readable or

writable in this mode. All reads and writes must take

place through the Timer1 High Byte Buffer register.

Writes to TMR1H do not clear the Timer1 prescaler.

The prescaler is only cleared o n writes to TMR 1L.

RA1

RA4

RB0

MCLR

VSS

RA2

RA3

Note: Not drawn to scale.

RA3

RB2

OSC1

RB5

OSC2

VDD

RB7

RB6

Note: The special event triggers from the CCP1

module will not set interrupt flag bit,

TMR1IF (PIR1<0>).

PIC18F1220/1320

12.7 Using Timer1 as a

Real-Time Clock

Adding an extern al LP os cilla tor to Tim er1 (such a s the

one described in Section 12.2 “Timer1 Oscillator”,

above), g ives user s the optio n to include R TC f unction-

ality to their applications. This is accomplished with an

inexpensive watch crystal to provide an accurate time

base and several lines of application code to calculate

the time. When operating in Sleep mode and using a

battery or supercapacitor as a power source, it can

completely eliminate the need for a separate RTC

dev ice and bat tery backup.

The application code routine, RTCisr, shown in

Example 12-1, demonstrates a simple method to

increment a counter at one-second intervals using an

Interrupt Serv ice R ou tin e. I nc rem enti ng the TM R1 re g-

ister p air to overf low, triggers the i nterrupt and ca lls th e

routine, w hich increme nts the seco nds co unter by on e;

additional counters for minutes and hours are

incremented as the previous counter overflow.

Since the register pair is 16 bits wide, counting up to

overflow the register directly from a 32.768 kHz clock

would take 2 seconds. To force the overflow at the

required one-second intervals, it is necessary to pre-

load it; the simplest method is to set the MSb of TMR1H

with a BSF instruction. Note that the TMR1L register is

never preloaded or altered; doing so may introduce

cumulative error over many cycles.

For this m ethod to be a ccurate, T i mer1 must o perate in

Asynchronous mode and the Timer1 overflow interrupt

must be enabled (PIE1<0> = 1), as shown in the

routine, RTCinit. The Timer1 oscillator must also be

enabled and running at all times.

EXAMPLE 12-1: IMPLEMENTING A REAL-TIME CLOCK USING A TIMER1 INTERRUPT SERVICE

RTCinit

MOVLW 0x80 ; Preload TMR1 register pair

MOVWF TMR1H ; for 1 second overflow

CLRF TMR1L

MOVLW b’00001111’ ; Configure for external clock,

MOVWF T1OSC ; Asynchronous operation, external oscillator

CLRF secs ; Initialize timekeeping registers

CLRF mins ;

MOVLW .12

MOVWF hours

BSF PIE1, TMR1IE ; Enable Timer1 interrupt

RETURN

RTCisr

BSF TMR1H, 7 ; Preload for 1 sec overflow

BCF PIR1, TMR1IF ; Clear interrupt flag

INCF secs, F ; Increment seconds

MOVLW .59 ; 60 seconds elapsed?

CPFSGT secs

RETURN ; No, done

CLRF secs ; Clear seconds

INCF mins, F ; Increment minutes

MOVLW .59 ; 60 minutes elapsed?

CPFSGT mins

RETURN ; No, done

CLRF mins ; clear minutes

INCF hours, F ; Increment hours

MOVLW .23 ; 24 hours elapsed?

CPFSGT hours

RETURN ; No, done

MOVLW .01 ; Reset hours to 1

MOVWF hours

RETURN ; Done

PIC18F1220/1320

TABLE 12-2: REGISTERS ASSOCIATED WITH TIMER1 AS A TIMER/COUNTER

Na m e Bit 7 B it 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 B it 0 Value on

POR, BOR

Value on

all other

Resets

INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u

PIR1 —ADIF RCIF TXIF —CCP1IF TMR2IF TMR1IF -000 -000 -000 -000

PIE1 —ADIE RCIE TXIE —CCP1IE TMR2IE TMR1IE -000 -000 -000 -000

IPR1 —ADIP RCIP TXIP —CCP1IP TMR2IP TMR1IP -111 -111 -111 -111

TMR1L Holding Register for the Least Significant Byte of the 16-bit TMR1 Register xxxx xxxx uuuu uuuu

TMR1H Holding Register for the Most Significant Byte of the 16-bit TMR1 Register xxxx xxxx uuuu uuuu

T1CON RD16 T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON 0000 0000 u0uu uuuu

Legend: x = unknown, u = unchanged, – = unimplemented, read as ‘0’. Shaded cells are not used by the Timer1 module.

PIC18F1220/1320

13.0 TIMER2 MODULE

The Timer2 module timer has the following features:

• 8-bit timer (TMR2 register)

• 8-bit period register (PR2)

• Readable and writable (both registers)

• Software programmable prescaler (1:1, 1:4, 1:16)

• Software programmable postscaler (1:1 to 1:16)

• Interrupt on TMR2 match with PR2

Timer2 has a control register shown in Register 13-1.

TMR2 can be shut off by cleari ng control bit, TMR2ON

(T2CON<2>), to minimize power consumption.

Figure 13-1 is a simplified block diagram of the Timer2

module. Register 13-1 shows the Timer2 Control

Timer2 are controlled by this register.

13.1 Timer2 Operation

Timer2 can be used as the PWM time base for the

PWM mode of the CCP module. The TMR2 register is

readable and writable and is cleared on any device

Reset. The i npu t clo ck (FOSC/4) has a prescale option

of 1:1, 1:4 or 1:16, selected by control bits,

T2CKPS1:T2CKPS0 (T2CON<1:0>). The match out-

put of TMR2 goes through a 4-bit postscaler (which

gives a 1:1 to 1:16 scaling inclusive) to generate a

TMR2 interrupt (latched in flag bit, TMR2IF (PIR1<1>)).

The prescaler and postscaler counters are cleared

when any of the following occurs:

• A write to the TMR2 register

• A write to the T2CON register

• Any device Reset (Power-on Reset, MCLR Rese t,

Watchdog Timer Reset or Brown-out Reset)

TMR2 is not cleared when T2CON is written.

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0

bit 7 bit 0

bit 7 Unimplemented: Read as ‘0’

bit 6-3 TOUTPS3:TOUTPS0: Timer2 Output Postscale Select bits

0000 = 1:1 Postscal e

0001 = 1:2 Postscal e

•

1111 = 1:16 Postscale

bit 2 TMR2ON: Ti mer2 On bit

1 = Timer2 is on

0 = Timer2 is off

bit 1-0 T2CKPS1:T2CKPS0: Timer2 Clock Prescale Select bits

00 = Prescaler is 1

01 = Prescaler is 4

1x = Prescaler is 16

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

13.2 Timer2 Interrupt

The Timer2 module has an 8-bit period register, PR2.

Timer2 increments from 00h until it matches PR2 and

then resets to 00h on the next increment cycle. PR2 is

a readable and writable register. The PR2 register is

initialized to FFh upon Reset.

13.3 Output of TMR2

The output of TMR2 (before the post scaler) is fed to the

Synchron ous Serial Port mod ule, which opti onally use s

it to generate the shift clock.

FIGURE 13-1: TIMER2 BLOCK DIAGRAM

TABLE 13-1: REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER

Comparator

TMR2 Sets Flag

TMR2

Output(1)

Reset

Postscaler

Prescaler

PR2

FOSC/4

1:1 to 1:16

1:1, 1:4, 1:16

bit TMR2IF

TOUTPS3:TOUTPS0

T2CKPS1:T2CKPS0

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on

POR, BOR

Value on

all other

Resets

INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u

PIR1 —ADIF RCIF TXIF —CCP1IF TMR2IF TMR1IF -000 -000 -000 -000

PIE1 —ADIE RCIE TXIE —CCP1IE TMR2IE TMR1IE -000 -000 -000 -000

IPR1 —ADIP RCIP TXIP —CCP1IP TMR2IP TMR1IP -111 -111 -111 -111

TMR2 Timer2 Module Register 0000 0000 0000 0000

T2CON — TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000

PR2 Timer2 Period Register 1111 1111 1111 1111

Legend: x = unknown, u = unchanged, – = unimplemented, read as ‘0’. Shaded cells are not used by the Timer2 module.

PIC18F1220/1320

14.0 TIMER3 MODULE

The Timer3 module timer/counter has the following

features:

• 16-bit timer/counter

(two 8-bit registers; TMR3H and TMR3L)

• Readable and writable (both registers)

• Internal or external clock select

• Interrupt-on-overflow from FFFFh to 0000h

• Reset from CCP module trigger

Figure 14-1 is a simplified block diagram of the Timer3

module.

module and sets the CCP clock source.

module, as well as contains the Timer1 Oscillator

Enable bit (T1OSCEN), which can be a clock sour ce for

Timer3.

R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

RD16 — T3CKPS1 T3CKPS0 T3CCP1 T3SYNC TMR3CS TMR3ON

bit 7 bit 0

bit 7 RD16: 16-bit Read/Write Mode Enable bit

1 = Enables register read/write of Timer3 in one 16-bit operation

0 = Enables register read/write of Timer3 in two 8-bit operations

bit 6 Unimplemented: Read as ‘0’

bit 5-4 T3CKPS1:T3CKPS0: Timer3 Input Clock Prescale Select bits

11 = 1:8 Prescale value

10 = 1:4 Prescale value

01 = 1:2 Prescale value

00 = 1:1 Prescale value

bit 3 T3CCP1: Timer3 and Timer1 to CCP1 Enable bits

1 = Timer3 is the clock source for compare/capture CCP module

0 = Timer1 is the clock source for compare/capture CCP module

bit 2 T3SYNC: Timer3 External Clock Input Synchronizat ion C ontr ol bit

(Not usable if the system clock comes from Timer1/Timer3.)

When TMR3CS = 1:

1 = Do not synchronize external clock input

0 = Synchronize external clock input

When TMR3CS = 0:

This bit is ignored. Timer3 uses the internal clock when TMR3CS = 0.

bit 1 TMR3CS: Timer3 Clock Source Select bit

1 = External clock input from Timer1 oscillator or T13CKI

(on the rising edge after the first falling edge)

0 = Internal clock (FOSC/4)

bit 0 TMR3ON: Timer3 On bit

1 = Enables Timer3

0 = Stops Timer3

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

14.1 Timer3 Operation

Timer3 can operate in one of these modes:

•As a timer

• As a synchronous counter

• As an asynchronous counter

The operating mode is determined by the clock select

bit, TMR3CS (T3CON<1>).

When TMR3CS = 0, Timer3 increments every instruc-

tion cycle. When TMR3CS = 1, Timer 3 increm ents on

every rising edge of the Timer1 external clock input or

the Timer1 oscillator, if enabled.

When the Timer1 oscillator is enabled (T1OSCEN is

set), the RB7/PGD/T1OSI/P1D/KBI3 and RB6/PGC/

T1OSO/T13CKI/P1C/KBI2 pins become inputs. That

is, the TRISB7:TRISB6 value is ignored and the pins

are read as ‘0’.

Timer3 also has an internal “Reset input”. This Reset

can be generated by the CCP module (see

Section 15.4.4 “Special Event Trigger”).

FIGURE 14-1: TIMER3 BLOCK DIAGRAM

FIGURE 14-2: TIMER3 BLOCK DIAGRAM CONFIGURED IN 16-BIT READ/WRITE MODE

TMR3H TMR3L

T1OSC

T3SYNC

TMR3CS

T3CKPS1:T3CKPS0

Peripheral Clocks

T1OSCEN

Enable

Oscillator(1)

TMR3IF

Overflow

Interrupt

FOSC/4

Internal

Clock

TMR3ON

On/Off

Prescaler

1, 2, 4, 8 Synchronize

det

Synchronized

Clock Input

T1OSO/

T1OSI

Flag bit

Note 1: When enable bit, T1OSCEN, is cleared, the inverter and feedback resistor are turned off. This eliminates power drain.

T13CKI

CLR

CCP Special Event Tr igger

T3CCPx

Timer3

TMR3L

T1OSC T3SYNC

TMR3CS

T3CKPS1:T3CKPS0 Peripheral

T1OSCEN

Enable

Oscillator(1)

FOSC/4

Internal

Clock

TMR3ON

On/Off

Prescaler

1, 2, 4, 8 Synchronize

det

Synchronized

Clock Input

T1OSO/

T1OSI

TMR3

T13CKI

CLR

CCP Special Event Trigger

T3CCPx

To T imer1 Clock Input

Note 1: When the T1OSCEN bit is cleared, the inverter and feedback resistor are turned off. Th is eliminates power drain.

High Byte

Data Bus<7:0>

TMR3H 8

Read TMR3L

Write TMR3L

Set TMR3IF Flag bit

on Overflow

Clocks

PIC18F1220/1320

14.2 Timer1 Oscillator

The Timer1 oscill ator may be us ed as the clo ck so urc e

for Timer3. The Timer1 oscillator is enabled by setting

the T1OSC EN (T 1CON<3>) bit. The oscil lator i s a low-

power oscillator rated for 32 kHz crystals. See

Section 12.2 “Timer1 Oscillator” for further details.

14.3 Timer3 Interrupt

The TMR3 register pair (TMR3H:TMR3L) increments

from 0000h to FFFFh and rolls over to 0000h. The

TMR3 interrupt, if enabled, is generated on overflow,

which is latched in interrupt flag bit, TMR3IF

(PIR2<1>). This interrupt can be enabled/disabled by

setting/clearing TMR3 Interrupt Enable bit, TMR3IE

(PIE2<1>).

14.4 Resetting Ti mer3 Us ing a CCP

Trigger Output

If the CCP module is configured in Compare mode

to generate a “special event trigger”

(CCP1M3:CCP1M0 = 1011), this signal will reset

Ti m e r3 . S e e Section 15.4.4 “Special Event Trigger”

for more information.

T imer 3 must be co nfigured fo r either T i mer or Synch ro-

nized Counter mode to take advantage of this feature.

If Timer3 is running in Asynchronous Counter mode,

this Reset operation may not work. In the event that a

write to Timer3 coincides with a special event trigger

from CCP1 , the write will t ake precedence. In this mode

of operation, the CCPR1H:CCPR1L register pair

effectively becomes the period register for Timer3.

TABLE 14-1: REGISTERS ASSOCIATED WITH TIMER3 AS A TIMER/COUNTER

Note: The special event triggers from the CCP

module will not set interrupt flag bit,

TMR3IF (PIR1<0>).

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on

POR, BOR

Value on

all other

Resets

INTCON GIE/

GIEH PEIE/

GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u

PIR2 OSCFIF — — EEIF —LVDIF TMR3IF —0--0 -00- 0--0 -00-

PIE2 OSCFIE — — EEIE —LVDIE TMR3IE —0--0 -00- 0--0 -00-

IPR2 OSCFIP — — EEIP —LVDIP TMR3IP —1--1 -11- 1--1 -11-

TMR3L Holding Register for the Least Significant Byte of the 16-bit TMR3 Register xxxx xxxx uuuu uuuu

TMR3H Holding Register for the Most Significant Byte of the 16-bit TMR3 Register xxxx xxxx uuuu uuuu

T1CON RD16 T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON 0000 0000 u0uu uuuu

T3CON RD16 — T3CKPS1 T3CKPS0 T3CCP1 T3SYNC TMR3CS TMR3ON 0-00 0000 u-uu uuuu

Legend: x = unknown, u = unchanged, – = unimplemented, read as ‘0’. Shaded cells are not used by the Timer3 module.

PIC18F1220/1320

NOTES:

PIC18F1220/1320

15.0 ENHANCED CAPTURE/

COMPARE/PWM (ECCP)

MODULE

The Enhanced CCP module is implemented as a

standard CCP module with Enhanced PWM

capabilities. These capabilities allow for 2 or 4 output

channels, user-selectable polarity, dead-band control

and autom atic shut down an d restart an d are discus sed

in detail in Section 15.5 “Enhanced PWM Mode”.

The control register for CCP1 is shown in Register 15-1.

In addition to the expanded functions of the CCP1CON

registers associated with Enhanced PWM operation

and auto-shutdown features:

•PWM1CON

• ECCPAS

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

P1M1 P1M0 DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0

bit 7 bit 0

bit 7-6 P1M1:P1M0: PWM Output Configuration bits

If CCP1M<3:2 > = 00, 01, 10:

xx = P1A assigned as Capture/Compare input; P1B, P1C, P1D assigned as port pins

If CCP1M<3:2 > = 11:

00 = Single output; P1A modulated; P1B, P1C, P1D assigned as port pins

01 = Full-bridge output forward; P1D modulated; P1A active; P1B, P1C inactive

10 = Half-bridge output; P1A, P1B modulated with dead-band control; P1C, P1D assigned as

port pins

11 = Full-bridge output reverse; P1B modulated; P1C active; P1A, P1D inactive

bit 5-4 DC1B1:DC1B0: PWM Duty Cycle Least Sign ifi ca nt bit s

Capture mode:

Unused.

Compare mode:

Unused.

PWM mo de:

These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPR1L.

bit 3-0 CCP1M3:CCP1M0: ECCP1 Mode Select bits

0000 = Capture/Compare/PWM off (resets ECCP module)

0001 = Unused (reserved)

0010 = Compare mode, toggle output on match (ECCP1IF bit is set)

0011 = Unused (reserved)

0100 = Capture mode, ever y fal lin g edge

0101 = Capture mode, ever y rising edge

0110 = Capture mode, every 4th rising edge

0111 = Capture mode, ever y 16t h risin g edge

1000 = Compare mode, set output on match (ECCP1IF bit is set)

1001 = Compare mode, clear output on match (ECCP1IF bit is set)

1010 = Compare mode, generate software interrupt on match (ECCP1IF bit is set,

ECCP1 pin returns to port pin operation)

1011 = Compare mode, trigger special event (ECCP1IF bit is set; ECCP resets TMR1 or

TMR3 and starts an A/D conversion if the A/D module is enabled)

1100 = PWM mode; P1A, P1C active-high; P1B, P1D active-high

1101 = PWM mode; P1A, P1C active-high; P1B, P1D active-low

1110 = PWM mode; P1A, P1C active-low; P1B, P1D active-high

1111 = PWM mode; P1A, P1C active-low; P1B, P1D active-low

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

15.1 ECCP Outputs

The Enhanced CCP module may have up to four

outputs, depending on the selected operating mode.

These outputs, designated P1A through P1D, are

multiplexed with I/O pins on PORTB. The pin

assignments are summarized in Table 15-1.

To configure I/O pins as PWM o utputs, the prop er PWM

mode must be selected by setting the P1Mn and

CCP1Mn bits (CCP1CON<7:6> and <3:0>,

resp ecti vely) . The a ppro pria te TRI SB dir ecti on bits for

the port pins must also be set as outputs.

TABLE 15-1: PIN ASSIGNMENTS FOR VARIOUS ECCP MODES

15.2 CCP Module

Capture/Compare/PWM Register 1 (CCPR1) is com-

prised of two 8-bit registers: CCPR1L (low byte) and

CCPR1H (high byte). The CCP1CON register controls

the operation of CCP1. All are readable and writable.

TABLE 15-2: CCP MODE – TIMER

RESOURCE

15.3 Capture Mode

In Capture mode, CCPR1H:CCPR1L captures the 16-bit

value of the TMR1 or TMR3 registers when an event

occurs on pin RB3/CCP1/P1A. An event is defined as

one of the following:

• every falling edge

• every rising edge

• every 4th rising edge

• every 16th rising edge

The event is selected by co ntrol bits, CCP1M3:CCP1M0

(CCP1CON<3:0>). When a capture is made, the inter-

rupt request flag bit, CCP1IF (PIR1<2>), is set; it must

be cleared in software. If another capture occurs before

the value in register CCPR1 is read, the old captured

value is overwritten by th e new captured valu e.

15.3.1 CCP PIN CONFIGURATION

In Capture mode, the RB3/CCP1/P1A pin should be

configu red as an input by setting the TRISB<3> bit.

15.3.2 TIMER1/TIMER3 MODE SELECTION

The timers that are to be used with the capture featu re

(either Timer1 and/or T imer3 ) mus t be runn ing i n Timer

mode or Synchronized Counter mode. In Asynchro-

nous Counter mode, the capture operation may not

work. The timer to be used with the CCP module is

selected in the T3CON register.

15.3.3 SOFTWARE INTERRUPT

When the Capture mode is changed, a false capture

interrupt may be generated. The user should keep bit,

CCP1IE (PIE1<2>), clear while changing capture

modes to avoid false interrupts and should clear the

flag bit, CCP1IF, following any such change in

operating mode.

ECCP Mode CCP1CON

Configuration RB3 RB2 RB6 RB7

Compatible CCP 00xx 11xx CCP1 RB2/INT2 RB6/PGC/T1OSO/T13CKI/KBI2 RB7/PGD/T1OSI/KBI3

Dual PWM 10xx 11xx P1A P1B RB6/PGC/T1OSO/T13CKI/KBI2 RB7/PGD/T1OSI/KBI3

Quad PWM x1xx 11xx P1A P1B P1C P1D

Legend: x = Don’t care. Shaded cells indicate pin assignments not used by ECCP in a given mode.

Note 1: TRIS register values must be configured appropriately.

CCP Mode Timer Resource

Capture

Compare

PWM

Timer1 or Timer3

Timer2

Note: If the RB3/CCP1/P1A is configured as an

output, a write to the port can cause a

capture condition.

PIC18F1220/1320

15.3.4 CCP PRESCALER

There are four prescaler settings, specified by bits

CCP1M3:CCP1M0. Whenever the CCP module is

turned off or the CCP module is not in Capture mode,

the prescaler counter is cleared. This means that any

Reset will clear the prescaler counter.

Switching from one capture prescaler to another may

generate an interrupt. Also, the prescaler counter will

not be cl eare d; therefore, the first c ap ture m ay be fro m

a non-zero prescaler. Example 15-1 shows the

recommended method for switching between capture

prescalers. This example also clears the prescaler

counter and will not generate the “false” interrupt.

EXAMPLE 15-1: CHANGIN G BETWEEN

CAPTURE PRESCALERS

FIGURE 15-1: CAPTURE MODE OPERATION BLOCK DIAGRAM

15.4 Compare Mode

In C ompare mo de, t he 16- bit CC PR1 re gist er va lue is

constantly compared against either the TMR1 register

pair value, or the TMR3 register pair value. When a

match occurs, the RB3/CCP1/P1A pin:

• Is driv en high

•Is driven low

• Toggles output (high-to-low or low-to-high)

• Remains unchanged (interrupt only)

The action on the pin is based on the value of control

bits, CCP1M3:CCP1M0. At the same time, interrupt

flag bit, CCP1IF, is set.

15.4.1 CCP PIN CONFIGURATION

The user mus t c onfigure the R B3/ CCP1 /P1A p in as an

output by clearing the TRISB<3> bit.

15.4.2 TIMER1/TIMER3 MODE SELECTION

Timer1 and/or Timer3 must be running in Timer mode

or Synchronized Counter mode if the CCP module is

using the compare feature. In Asynchronous Counter

mode, the compare operation may not work.

15.4.3 SOFTWARE INTERRUPT MODE

When generate software interrupt is chosen, the RB3/

CCP1/P1A pin is not affected. CCP1IF is set and an

interrupt is genera ted (if enab led).

15.4.4 SPECIAL EVENT TRIGGER

In this mod e, an internal hardw are trigger is generated,

which may be used to initiate an action.

The special event trigger output of CCP1 resets the

TMR1 re giste r pai r. T his allo ws t he CC PR 1 re gis ter to

ef fectively b e a 16-bit progra mmable pe riod registe r for

Timer1.

The special event trigger also sets the GO/DONE bit

(ADCON0<1>). This starts a conversion of the

currently selected A/D channel if the A/D is on.

CLRF CCP1CON ; Turn CCP module off

MOVLW NEW_CAPT_PS ; Load WREG with the

; new prescaler mode

; value and CCP ON

MOVWF CCP1CON ; Load CCP1CON with

; this value

CCPR1H CCPR1L

TMR1H TMR1L

Set Flag bit CCP1IF TMR3

Enable

Q’s CCP1CON<3:0>

CCP1 pin

Prescaler

÷ 1, 4, 16

and

Edge Detect

TMR3H TMR3L

TMR1

Enable

T3CCP1

Note: Clearing the CCP1CON register will force

the RB3/CCP1/P1A compare output latch

to the default low level. This is not the

PORTB I/O data latch.

PIC18F1220/1320

FIGURE 15-2: COMPARE MODE OPERATION BLOCK DIAGRAM

TABLE 15-3: REGISTERS ASSOCIATED WITH CAPTURE, COMPARE, TIMER1 AND TIMER3

CCPR1H CCPR1L

TMR1H TMR1L

Comparator

ROutput

Logic

Special Event Trigger

Set Flag bit CCP1IF

Match

RB3/CCP1/P1A pin

TRISB<3> CCP1CON<3:0>

Mode Select

Output Enable

Special Event Trig ger will:

Reset Timer1 or Timer3, but does not set Timer1 or Timer3 interrupt flag bit

and set bit GO/DONE (ADCON0<2>), which starts an A/D conversion.

TMR3H TMR3L

T3CCP1 1

Name Bit 7 Bit 6 Bit 5 B it 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on

POR, BOR

Value on

all other

Resets

INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u

PIR1 —ADIF RCIF TXIF — CCP1IF TMR2IF TMR1IF -000 -000 -000 -000

PIE1 —ADIE RCIE TXIE — CCP1IE TMR2IE TMR1IE -000 -000 -000 -000

IPR1 —ADIP RCIP TXIP — CCP1IP TMR2IP TMR1IP -111 -111 -111 -111

TRISB PORTB Data Direction Register 1111 1111 1111 1111

TMR1L Holding Register for the Least Significant Byte of the 16-bit TMR1 Register xxxx xxxx uuuu uuuu

TMR1H Holding Register for the Most Significant Byte of the 16-bit TMR1 Register xxxx xxxx uuuu uuuu

T1CON RD16 T1RUN T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON 0000 0000 uuuu uuuu

CCPR1L Capture/Compare/PWM Register 1 (LSB) xxxx xxxx uuuu uuuu

CCPR1H Capture/Compare/PWM Register 1 (MSB) xxxx xxxx uuuu uuuu

CCP1CON P1M1 P1M0 DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 0000 0000 0000 0000

TMR3L Holding Register for the Least Significant Byte of the 16-bit TMR3 Register xxxx xxxx uuuu uuuu

TMR3H Holding Register for the Most Significant Byte of the 16-bit TMR3 Register xxxx xxxx uuuu uuuu

T3CON RD16 — T3CKPS1 T3CKPS0 T3CCP1 T3SYNC TMR3CS TMR3ON 0-00 0000 u-uu uuuu

ADCON0 VCFG1 VCFG0 —CHS2 CHS1 CHS0 GO/DONE ADON 00-0 0000 00-0 0000

Legend: x = unknown, u = unchanged, – = unimplemented, read as ‘0’. Shaded cells are not used by Capture and Timer1.

PIC18F1220/1320

15.5 Enhanced PWM Mode

The Enhanced PWM Mode provides additional PWM

output options for a broader range of control applica-

tions. Th e module i s an upwardl y compat ible vers ion of

the st andard CCP m odule and o ffers up to four output s,

designated P1A through P1D. Users are also able to

select the polarity of the signal (either active-high or

active -low). The module’ s outpu t mode an d polarit y are

configured by setting the P1M1:P1M0 and

CCP1M3CCP1M0 bits of the CCP1CON register

(CCP1CON<7:6> and CCP1CON<3:0>, respectively).

Figure 15-3 shows a simplified block diagram of PWM

operation. All control registers are double-buffered and

are loaded at the beginning of a new PWM cycle (the

period boundary w hen Ti mer2 resets) in order to prevent

glitches on any of the outputs. The exception is the PWM

Delay register , ECCP1DEL, which is loaded at either the

duty cycle boundary or the boundary period (whichever

comes first). Because of the buf fering, the m odule w ait s

until the assigned timer resets instead of starting imme-

diately. This means that Enhanced PWM waveforms do

not exactly match the standard PWM waveforms, but

are instead of fse t by one full ins truction cy cle (4 TOSC).

As before, the user must manually configure the

appropriate TRIS bits for output.

15.5.1 PWM PERIOD

The PWM period is specified by writing to the PR2

equation:

EQUATION 15-1: PWM PERIOD

PWM frequency is defined as 1/[PWM period]. When

TMR2 is e qual to PR 2, the fol lowing three event s occur

on the next increment cycle:

• TMR2 is cl eare d

• The CCP 1 pin i s set (if PWM duty cycl e = 0%, the

CCP1 pin will not be set)

• The PWM duty cy c le is copied from CCPR 1 L into

CCPR1H

15.5.2 PWM DUTY CYCLE

The PWM duty cycle is specified by writing to the

CCPR1L register and to the CCP1CON<5:4> bits. Up

to 10- b i t re so l uti on is av ai l ab le. T he CC PR 1 L c ontai ns

the eight MSbs and the CCP1CON<5:4> contains the

two LSbs. This 10-bit value is represented by

CCPR1L:CCP1CON<5:4>. The PWM duty cycle is

calculated by the equation:

EQUATION 15-2: PWM DUTY CYCLE

CCPR1L and CCP1CON<5:4> can be written to at any

time, but the duty cycle value is not copied into

CCPR1H un til a match between PR2 and TMR2 occurs

(i.e., the period is complete). In PWM mode, CCPR1H

is a read- only regi ster.

The CCPR1H register and a 2-bit internal latch are

used to double-buffer the PWM duty cycle. This

double-buffering is essential for glitchless PWM

operation. When the CCPR1H and 2-bit latch match

TMR2, concatenated with an internal 2-bit Q clock or

two bits of the TMR2 prescaler, the CCP1 pin is

cleared. The maximum PWM resolution (bits) for a

given PWM frequency is given by the equation:

EQUATION 15-3: PWM RESOLUTION

15.5.3 PWM OUTPUT CONFIGURATIONS

The P1M1:P1M0 bits in the CCP1CON register allow

one of four configurations:

• Single Output

• Half-Bridge Output

• Full-Brid ge Output, For ward mode

• Full-Bridge Output, Reverse mode

The Single Output mode is the Standard PWM mode

discussed in Section 15.5 “Enhanced PWM Mode”.

The Half-Bridge and Full-Bridge Output modes are

covered in detail in the sections that follow.

The general relationship of the outputs in all

configurations is summarized in Figure 15-4.

TABLE 15-4: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 40 MHz

Note: The Timer2 postscaler (see Section 13.0

“Timer2 Module”) is not used in the

determination of the PWM frequency. The

pos ts caler c ould be us ed to have a servo

update rate at a different frequency than

the PWM output.

PWM Period = [(PR2) + 1] • 4 • TOSC •

(TMR2 Prescale Value)

Note: If the PWM d uty c ycle v alu e i s lon ger tha n

the PWM period, the CCP1 pin will not be

cleared.

PWM Duty Cycle = (CCP R1L:CCP1CON<5: 4>) •

TOSC • (TMR2 Prescale Value)

( )

PWM Resolution (max) =

FOSC

FPWM

log

log(2) bits

PWM Frequency 2.44 kHz 9.77 kHz 39.06 kHz 156.25 kHz 312.50 kHz 416.67 kHz

Timer Prescaler (1, 4, 16) 1641111

PR2 Value FFh FFh FFh 3Fh 1Fh 17h

Maximum Resolut ion (bits) 10 10 10 8 7 6.58

PIC18F1220/1320

FIGURE 15-3: SIMPLIFIED BLOCK DIAGRAM OF THE ENHANCED PWM MODULE

FIGURE 15-4: PWM OUTPUT RELATIONSHIPS (ACTIVE-HIGH STATE)

CCPR1L

CCPR1H (Slave)

Comparator

TMR2

Comparator

PR2

(Note 1)

Duty Cycle Registers CCP1CON<5:4>

Clear Timer,

set CCP1 pin and

latch D.C.

Note: The 8-bit TMR2 register is concatenated with the 2-bit internal Q clock, or 2 bits of the prescaler to create the

10-bit time base.

TRISB<3>

RB3/CCP1/P1A

TRISB<2>

RB2/P1B/INT2

TRISB<6>

RB6/PGC/T1OSO/T13CKI/

TRISB<7>

RB7/PGD/T1OSI/P1D/KBI3

Output

Controller

P1M1<1:0> 2CCP1M<3:0>

CCP1DEL

CCP1/P1A

P1B

P1C

P1D

P1C/KBI2

Period

SIGNAL PR2+1

CCP1CON<7:6>

P1A Modulated

P1B Modulated

P1A Acti ve

P1B Inactive

P1C Inactive

P1D Modulated

P1A Inactive

P1B Modulated

P1C Ac tive

P1D Inactive

Duty

Cycle

(Single Output)

(Half-Bridge)

(Full-Bridge,

Forward)

(Full-Bridge,

Reverse)

Delay(1) Delay(1)

PIC18F1220/1320

FIGURE 15-5: PWM OUTPUT RELATIONSHIPS (ACTIVE-LOW STATE)

Period

SIGNAL PR2+1

CCP1CON<7:6>

P1A Modulated

P1B Modulated

P1A Ac ti ve

P1B Inactive

P1C Inactive

P1D Modulated

P1A Inactive

P1B Modulated

P1C Active

P1D Inactive

Duty

Cycle

(Single Output)

(Half-Bridge)

(Full-Bridge,

Forward)

(Full-Bridge,

Reverse)

Delay(1) Delay(1)

Relationships:

• Period = 4 * TOSC * (PR2 + 1) * (TMR2 Prescale Value)

• Duty Cyc le = TOSC * (CCPR1L<7:0>:CCP1CON<5:4>) * (TMR2 Pre scale Value)

• Delay = 4 * TOSC * (PWM1CON<6:0>)

Note 1: Dead-band delay is programmed using the PWM1CON register (Section 15.5.6 “Programmable Dead-Band

Delay”).

PIC18F1220/1320

15.5.4 HALF-BRIDGE MODE

In the Half-Bridge Output mode, two pins are used as

outputs to drive push-pull loads. The PWM output

signal is output on the RB3/CCP1/P1A pin, while the

complementary PWM output signal is output on the

RB2/P1B/INT2 pin (Figure 15-6). This mode can be

used for half-bridge applications, as shown in

Figure 15-7, or for full-bridge applications, where four

power switches are being modulated with two PWM

signals.

In Half-Bridge Output mode, the programmable dead-

band delay can be used to prevent shoot-through

current in half-bridge power devices. The value of bits,

PDC6:PDC0 (PWM1CON<6:0>), sets the number of

instruction cycles before the output is driven active. If the

value is greater than the duty cycle, the corresponding

output remains inactive during the entire cycle. See

Section 15.5.6 “Programmable Dead-Band Delay”

for more details of the dead -ba nd delay op erations.

The TRISB<3> and TRISB<2> bits must be cleared to

configure P1A and P1B as outputs.

FIGURE 15-6: HALF-BRIDGE PWM

OUTPUT (ACTIVE-HIGH)

FIGURE 15-7: EXAMPLES OF HALF-BRIDGE OUTPUT MODE APPLICATIONS

Period

Duty Cycle

(1)

P1A

P1B

td = Dead-Band Delay

Period

(1) (1)

Note 1: At this time, the TMR2 register is equal to the

PR2 register.

PIC18F1220/1320

P1A

P1B

FET

Driver

FET

Driver

Load

FET

Driver

FET

Driver

V+

V-

Load

FET

Driver

FET

Driver

PIC18F1220/1320

P1A

P1B

St andard Half-Bridge Circuit (“Push-Pull”)

Half-Bridge Output Driving a Full-Bridge Circuit

PIC18F1220/1320

15.5.5 FULL-BRIDGE MODE

In Full-Bridge Output mode, four pins are used as

outputs; however , only two outputs are active at a time.

In the Forward mode, pin RB3/CCP1/P1A is continu-

ously active and pin RB7/PGD/T1OSI/P1D/KBI3 is

modulated. In the Reverse mode, pin RB6/PGC/

T1OSO/T13CKI/P1C/KBI2 is continuously active and

pin RB2/P1B/INT2 is modulated. These are illustrated

in Figure 15-8.

The TRISB<3:2> and TRISB<7:6> bits must be cleare d

to make the P1A, P1B, P1C and P1D pins output.

FIGURE 15-8: FULL-BRIDGE PWM OUTPUT (ACTIVE-HIGH)

Period

Duty Cycle

P1A

P1B

P1C

P1D

Forwar d Mo de

(1)

Period

Duty Cycle

P1A

P1C

P1D

P1B

Reverse Mode

(1)

Note 1: At this time, the TMR2 register is equal to the PR2 register.

PIC18F1220/1320

FIGURE 15-9: EXAMPL E OF FULL-BRIDGE APPLICATION

15.5.5.1 Directi on Chang e in Full- Bridge M ode

In the Full-Bridge Output mode, the P1M1 bit in the

CCP1CON register allows the user to control the

Forward/Reverse direction. When the application

firmware changes this direction control bit, the module

will assume the new direction on the next PWM cycle.

Just before the end of the current PWM period, the

modulated outputs (P1B and P1D) are placed in their

inactiv e state, whil e the unmodula ted outputs (P1A and

P1C) are switched to drive in the opposite direction.

This occurs in a time interval of (4 TOSC * (Timer2

Prescale Value) before the next PWM period begins.

The Timer2 prescaler will be either 1,4 or 16, depend-

ing on the value of the T2CKPS bit (T2CON<1:0>).

During the interval from the switch of the unmodulated

outputs to the beginning of the next period, the

modulated outputs (P1B and P1D) remain inactive.

This relationship is shown in Figure 15-10.

Note that in the Full-Bridge Output mode, the ECCP

module does not provide any dead-band delay. In

general, since only one output is modulated at all times,

dead-band delay is not required. However, there is a

situation where a dead-band delay might be required.

This situation occurs when both of the following

conditions are true:

1. The direction of the PWM output changes when

the duty cycle of the output is at or near 100%.

2. The tu rn-off ti me of the po wer swi tch, incl uding

the power device and driver circuit, is greater

than the turn-on tim e.

Figure 15-1 1 shows an example where the PWM direc-

tion changes from forward to reverse, at a near 100%

duty cy cle. At time t1, the output P1A a nd P1D becom e

inactive, while output P1C becomes active. In this

exampl e, since the turn-off time of the power devi ces is

longer than the turn-on time, a shoot-through current

may flow through power devices QC and QD (see

Figure 15-9) for the duration of ‘t’. The same phenom-

enon will occur to power devices QA and QB for PWM

direction change from reverse to forward.

If changing PWM direction at high duty cycle is required

for an application, one of the following requirements

must b e met:

1. Reduce PWM for a PWM period before

changing directions.

2. Use switch drivers that can drive the switches off

faster than they can drive them on.

Other options to prevent shoot-through current may

exist.

PIC18F1220/1320

P1A

P1C

FET

Driver

FET

Driver

V+

V-

Load

FET

Driver

FET

Driver

P1B

P1D

QB QD

PIC18F1220/1320

FIGURE 15-10: PWM DIRECTION CHANGE (ACTIVE-HIGH)

FIGURE 15-11: PWM DIRECTION CHANGE AT NEAR 100% DUTY CYCLE (ACTIVE-HIGH)

PWM Period(1)

SIGNAL

Note 1: The direction bit in the CCP1 Control register (CCP1CON<7>) is written any time during the PWM cycle.

2: When changing directions, the P1A and P1C toggle one Ti mer2 count before the end of the current PWM cycle.

The modulated P1B and P1D signals are inactive at this time.

PWM Period

One Time r2 Count(2)

P1A

P1B

P1C

P1D

Forward Period Reverse Period

P1A

tON

tOFF

t = tOFF – tON

P1B

P1C

P1D

External Switch D

Potential

Shoot-Through

Current

Note 1: tON is the turn-on delay of power switch QC and its driver.

2: tOFF is the turn-off delay of power switch QD and its driver.

External Switch C

PIC18F1220/1320

15.5.6 PROGRAMMABLE DEAD-BAND

DELAY

In half-b ridge applications where all power switches are

modulated at the PWM frequency at all times, the

power switches normally require more time to turn off

than to turn on. If both the upper and lower power

switc he s a re sw it ched at the same time (one turne d o n

and the other turned off), both switches may be on for

a short period of time until one switch completely turns

off. During this brief interv al, a very hig h current (sho ot-

through current) may flow through both power

switches, shorting the bridge supply. To avoid this

potentia lly des tructiv e shoot -through current from flow-

ing during switching, turning on either of the power

switches is normally delayed to allow the other switch

to completely turn off.

In the Half-Bridge Output mode, a digitally programmable

dead-band delay is available to avoid shoot-through

curre nt fro m destro ying t he bri dge po wer swit ches. The

delay oc curs at the sign al tra nsitio n from the non-acti ve

state to the active state. See Figure 15-6 for an illustra-

tion. The lower seven bits of the PWM1CON register

(Register 15-2) sets the delay period in terms of

microcontroller instruction cycles (TCY or 4 TOSC).

15.5.7 ENHANCED PWM

AUTO-SHUTDOWN

When the ECCP is programmed for any of the

Enhanced PWM modes, the active output pins may be

configured for auto-shutdown. Auto-shutdown immedi-

ately places the Enhanced PWM output pins into a

defined shutdown state when a shutdown event

occurs.

A shutdown event can be caused by the INT0, INT1 or

INT2 pi ns (or an y c ombin ation of these thre e s ourc es ).

The auto-shutdown feature can be disabled by not

selecting any auto-shutdown sources. The auto-

shutdown sources to be used are selected using the

ECCPAS2:ECCPAS0 bits (bits <6:4> of the ECCPAS

When a shutdown occurs, the output pins are

asynchronously placed in their shutdown states, spec-

ified by the PSSAC1:PSSAC0 and PSSBD1:PSSBD0

bits (ECCPAS<3:0>). Each pin pair (P1A/P1C and

P1B/P1D) may be set to drive high, drive low or be tri-

stated (not driving). The ECCPASE bit (ECCPAS<7>)

is also set to hold the Enhanced PWM outputs in their

shutdown states.

The ECCPASE bit is s et by hardware when a shutdow n

event o cc urs. If automati c re starts are no t e nab led , th e

ECCPASE bit is c leared by f irmware when t he caus e of

the shutdown clears. If automatic restarts are enabled,

the ECCPASE bit is automatically cleared when the

cause of the auto-shutdown has cleared.

If the ECCPASE bit is set when a PWM period begins,

the PWM o utputs remain in their shutdown state for that

entire PW M peri od. Wh en the ECCPASE bi t is cle ared,

the PWM outputs will return to normal operation at the

beginning of the next PWM period.

Note: Writing to the ECCPASE bit is disabled

while a shutdown condition is active.

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

PRSEN PDC6 PDC5 PDC4 PDC3 PDC2 PDC1 PDC0

bit 7 bit 0

bit 7 PRSEN: PWM Restart Enable bit

1 = Upon auto-shutdown, the ECCPASE bit clears automatically once the shutdown event

goes away; the PWM restarts automatically

0 = Upon auto-shutdown, ECCPASE must be cleared in software to restart the PWM

bit 6-0 PDC<6:0>: PWM Delay Count bits

Number of FOSC/4 (4 * TOSC) cycles b etween the sch edu led tim e w he n a PW M s ig nal should

transition active and the actual time it transitions active.

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

CONTROL REGISTER

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

ECCPASE ECCPAS2 ECCPAS1 ECCPAS0 PSSAC1 PSSAC0 PSSBD1 PSSBD0

bit 7 bit 0

bit 7 ECCPASE: ECCP Auto-Shutdown Event Status bit

0 = ECCP outputs are operating

1 = A shutdown event has occurred; ECCP outputs are in shutdown state

bit 6 ECCPAS2: ECCP Auto-Shutdown bit 2

0 = INT0 pin has no eff e ct

1 = INT0 pin low causes shutdown

bit 5 ECCPAS1: ECCP Auto-Shutdown bit 1

0 = INT2 pin has no eff e ct

1 = INT2 pin low causes shutdown

bit 4 ECCPAS0: ECCP Auto-Shutdown bit 0

0 = INT1 pin has no eff e ct

1 = INT1 pin low causes shutdown

bit 3-2 PSSACn: Pins A and C Shutdown State Control bits

00 = Drive Pins A and C to ‘0’

01 = Drive Pins A and C to ‘1’

1x = Pins A and C tri-state

bit 1-0 PSSBDn: Pins B and D Shutdown State Control bits

00 = Drive Pins B and D to ‘0’

01 = Drive Pins B and D to ‘1’

1x = Pins B and D tri-state

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

15.5.7.1 Auto-Shutdown and

Automatic Restart

The auto-shutdown feature can be configured to allow

automatic restarts of the module, following a shutdown

event. This is enabled by setting the PRSEN bit of the

PWM1CON register (PWM1CON<7>).

In Shut down mode with PRSEN = 1 (Figure 15-12), the

ECCPASE bit will remain set for as long as the cause

of the shutdown continues. When the shutdown

condition clears, the ECCPASE bit is automatically

cleared. If PRSEN = 0 (Figure 15-13), once a shutdown

conditi on occurs , the ECCPASE bit will rem ain set unti l

it is cleared by firmware. Once ECCPASE is cleared,

the Enhanc ed PWM will res ume at the be ginning of th e

next PWM period.

Independent of the PRSEN bit setting, the ECCPASE

bit cannot be cleared as long as the cause of the

shutdown persists.

The Auto-Shu tdown mode can be forced by writing a ‘1’

to the ECCPASE bit.

15.5.8 START-UP CONSIDERATIONS

When the EC CP module is use d in the PWM mode, th e

applic ation hardware m ust use the p roper external pull-

up and/or pull-down resistors on the PWM output pins.

When the microcontroller is released from Reset, all of

the I/O pins are in the high-impedance state. The

external circuit s must keep the power switch de vices in

the off state, until the microcontroller drives the I/O pins

with the proper signal levels, or activates the PWM

output(s).

The CCP1M1:CCP1M0 bits (CCP1CON<1:0>) allow

the user to choose whether the PW M output signals are

active-high or active-low for each pair of PWM output

pins (P1A/P1C and P1B/P1D). The PWM output

polarities must be selected before the PWM pins are

configu red as output s. Changin g the p olarity conf igura-

tion while the PWM pins are configured as outputs is

not recom mended, sinc e it may result i n damage to th e

application circuits.

The P1A, P1B, P1C and P1D outpu t latches m ay not be

in the proper sta tes when the PWM module is initial ized.

Enabling the PWM pins for output at the same time as

the ECCP module may cause damage to the applic ation

circuit. The ECCP module must be enabled in the proper

output mode and complete a full PWM cycle, before con-

figuring the PWM pins as outputs. The completion of a

full PWM cycle is indicated by the TMR2IF bit being set

as the second PWM period begins .

FIGURE 15-12: PWM AUTO-SHUTDOWN (PRSEN = 1, AUTO-RESTART ENABLED)

FIGURE 15-13: PWM AUTO-SHUTDOWN (PRSEN = 0, AUTO-RESTART DISABLED)

Note: Writing to the ECCPASE bit is disabled

while a shutdown condition is active.

Shutdown

PWM

ECCPASE bit

Activity

Event

PWM Period PWM Period PWM Per iod

Duty Cycle

Dead Time

Duty Cycle Duty Cycle

Dead Time

Shutdown

PWM

ECCPASE b i t

Activity

Event

PWM Period PWM Period PWM Period

ECCPASE

Cleared by Firmware

Duty Cycle

Dead Time

Duty Cycle Duty Cycle

Dead TimeDead Time

PIC18F1220/1320

15.5.9 SETUP FOR PWM OPERA TIO N

The following steps should be taken when configuring

the ECCP1 module for PWM operation:

1. Configure the PWM pins P1A and P1B (and

P1C and P1D, if used) as inputs by setting the

corresponding TRISB bits.

2. Set the PWM period by loading the PR2 register .

3. Configure the ECCP module for the desired

PWM mode and configuration by loading the

CCP1CON register with the appropriate values:

• Select one of the available output

configurations and direction with the

P1M1:P1M0 bits.

• Select the polarities of the PWM output

signals with the CCP1M3:CCP1M0 bits.

4. Set the PWM du ty cycle by loading the CCPR1L

5. For Half-Bridge Output mode, set the dead-

band delay by loading PWM1CON<6:0> with

the appropriate value.

6. If auto-shutdown operation is required, load the

ECCPAS register:

• Select the auto-shutdown sources using the

ECCPAS<2:0> bits.

• Select the shutdown states of the PWM

output pins using PSSAC1:PSSAC0 and

PSSBD1:PSSBD0 bits.

• Set the ECCPASE bit (ECCPAS<7>).

7. If auto-restart operation is required, set the

PRSEN bit (PWM1CON<7>).

8. Configure and start TMR2:

• Clear the TMR2 interrupt flag bit by clearing

the TMR2IF bit (PIR1<1>).

• Set the TMR2 prescale value by loading the

T2CKPS bits (T2CON<1:0>).

• Enable Timer2 by setting the TMR2ON bit

(T2CON<2>).

9. Enable PWM outputs after a new PWM cycle

has started:

• W a it until TMR 2 overflo ws (TMR 2IF bit is se t).

• Enable the CCP1/P1A, P1B, P1C and/or P1D

pin outputs by clearing the respective TRISB

bits.

• Clear the ECCPASE bit (ECCPAS<7>).

15.5.10 OPE RATION IN LOW-POW ER

MODES

In the Low-Power Sleep mode, all clock sources are

disabl ed. Timer2 will not inc r em en t a nd the s t ate of the

module will not change. If the ECCP pin is driving a

value, it will continue to drive that value. When the

device wake s up, i t will conti nue from this s tat e. If Two-

Speed Start-ups are enabled, the initial start-up

frequency may not be stable if the INTOSC is being

used.

In PRI_IDLE mode, the primary clock will continue to

clock the ECCP module without change.

In all other low-power modes, the selected low-power

mode clock will clock Timer2. Other low-power mode

clocks will most likely be different than the primary

clock frequency.

15.5.10.1 Operation with Fail-Safe

Clock Monitor

If the Fail-Safe Clock Monitor is enabled

(CONFIG1H<6> is programmed), a clock failure will

force the device into the Low-Power RC_RUN mode

and the OSCFIF bit (PIR2<7>) will be set. The ECCP

will then be clocked from the INTRC clock source,

which may have a different clock frequency than the

primary clock. By loading the IRCF2:IRCF0 bits on

Resets, the user can enable the INTOSC at a high

clock speed in the event of a clock failure.

See the previous section for additional details.

15.5.11 EFFECTS OF A RESET

Both power-on and subsequent Resets will force all

ports to input mode and the CCP registers to their

Reset states.

This forces the Enhanced CCP module to reset to a

state compatible with the standard CCP module.

PIC18F1220/1320

TABLE 15-5: REGISTERS ASSOCIATED WITH ENHANCED PWM AND TIMER2

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on

POR, BOR

Value on

all other

Resets

INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u

RCON IPEN — — RI TO PD POR BOR 0--1 11qq 0--q qquu

PIR1 —ADIF RCIF TXIF —CCP1IF TMR2IF TMR1IF -000 -000 -000 -000

PIE1 —ADIE RCIE TXIE —CCP1IE TMR2IE TMR1IE -000 -000 -000 -000

IPR1 —ADIP RCIP TXIP —CCP1IP TMR2IP TMR1IP -111 -111 -111 -111

TMR2 Timer2 Module Register 0000 0000 0000 0000

PR2 Timer2 Module Period Register 1111 1111 1111 1111

T2CON — TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000

TRISB PORTB Data Direc tion Register 1111 1111 1111 1111

CCPR1H Enhanced Capture/Compare/PWM Register 1 High Byte xxxx xxxx uuuu uuuu

CCPR1L Enhanced Capture/Compare/PWM Register 1 Low Byte xxxx xxxx uuuu uuuu

CCP1CON P1M1 P1M0 DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 0000 0000 0000 0000

ECCPAS ECCPASE ECCPAS2 ECCPAS1 ECCPAS0 PSSAC1 PSSAC0 PSSBD1 PSSBD0 0000 0000 0000 0000

PWM1CON PRSEN PDC6 PDC5 PDC4 PDC3 PDC2 PDC1 PDC0 0000 0000 uuuu uuuu

OSCCON IDLEN IRCF2 IRCF1 IRCF0 OSTS IOFS SCS1 SCS0 0000 qq00 0000 qq00

Legend: x = unknown, u = unchanged, – = unimplemented, read as ‘0’.

Shaded cells are not used by the ECCP module in Enhanced PWM mode.

PIC18F1220/1320

16.0 ENHANCED ADDRESSABLE

UNIVERSAL SYNCHRONOUS

ASYNCHRONOUS RECEIVER

TRANSMITTER (EUSART)

The Enhanced Addressable Universal Synchronous

Asynchronous Receiver Transmitter (EUSART) mod-

ule can be configured as a full-duplex asynchronous

system that can communicate with peripheral devices,

such as CRT terminals an d personal com pu ters . It ca n

also be configured as a half-duplex synchronous

system that can communicate with peripheral devices,

such as A/D or D/A integrated circuits, serial

EEPROMs, etc.

The Enhanced Addressable USART module

implements additional features, including automatic

baud rat e detecti on and c alibratio n, automa tic wake-u p

on Sync Break reception and 12-bit Break character

transmit. These features make it ideally suited for use

in Local Interconnect Network (LIN) bus systems.

The EUSART can be configured in the following

modes:

• Asynchronous (full duplex) with:

- Auto-wake-up on character reception

- Auto-baud calibration

- 12-bit Break charac ter tran sm is si on

• Synchronous – Master (half duplex) with

selectable clock polarity

• Synchron ous – Sl ave (half duplex) w ith sele ctable

clock polarity

The RB1/AN5/TX/CK/INT1 and RB4/AN6/RX/DT/KBI0

pins must be configured as follows for use with the

Universal Synchronous Asynchronous Receiver

Transmitter:

• SPEN (RCSTA<7>) bit must be set ( = 1),

• PCFG6:PCFG5 (ADCON1<5:6>) must be set ( = 1),

• TRISB<4> bit must be set ( = 1) and

• TRISB<1> bit must be set ( = 1).

The operation of the Enhanced USART module is

controlled through three registers:

• Transmit Status and Control (TXSTA)

• Receive Status and Control (RCSTA)

• Baud Rate Control (BAUDCTL)

These are detailed in on the following pages in

respectively.

16.1 Asynchronous Operation in Power

Managed Modes

The EUSART may operate in Asynchronous mode

while the peripheral clocks are being provided by the

internal oscillator block. This makes it possible to

remove the crystal or resonator that is commonly

connected as the primary clock on the OSC1 and

OSC2 pins.

The factory calibrates the internal oscillator block out-

put (INTOSC) for 8 MHz (see Table 22-6). However,

this frequency may drift as VDD or temperature

changes and this directly affects the asynchronous

baud rate. Two methods may be used to adjust the

baud rate clock, but both require a reference clock

source of some kind.

The first (preferred) method uses the OSCTUNE

Adjustin g the value i n the OSCTUNE reg ister allows f or

fine res olution changes to the system clock source (see

Section 3.6 “INTOSC Frequency Drift” for more

information).

The other method adjusts the value in the Baud Rate

Generator (BRG). There may not be fine enough

resolution when adjusting the Baud Rate Generator to

compensate for a gradual change in the peripheral

clock frequency.

Note: The EUSART control will automatically

reconfigure the pin from input to output as

needed.

PIC18F1220/1320

R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R-1 R/W-0

CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D

bit 7 bit 0

bit 7 CSRC: Clock Source Select bit

Asynchronous mode:

Don’t care.

Synchronous mode:

1 = Master mode (clock generated internally from BRG)

0 = Slave mode (clock from external source)

bit 6 TX9: 9-bit Transmit Enable bit

1 = Selects 9-bit transmission

0 = Selects 8-bit transmission

bit 5 TXEN: Transmit Enable bit

1 = Transmit enabled

0 = Transmit disabled

Note: SREN/CREN overrides TXEN in Sync mode.

bit 4 SYNC: EUSART Mode Select bit

1 = Synchronous mode

0 = Asynchronous mode

bit 3 SENDB: Send Break Character bit

Asynchronous mode:

1 = Send Sync Break on next transmission (cleared by hardware upon completion)

0 = Sync Break transmission completed

Synchronous mode:

Don’t care.

bit 2 BRGH: High Baud Rate Select bit

Asynchronous mode:

1 = High speed

0 = Low speed

Synchronous mode:

Unused in this mode .

bit 1 TRMT: Transmit Shift Register Status bit

1 = TSR Idle

0 =TSR busy

bit 0 TX9D: 9th bit of Transmit Data

Can be address/data bit or a parity bit.

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R-0 R-0 R-x

SPEN RX9 SREN CREN ADDEN FERR OERR RX9D

bit 7 bit 0

bit 7 SPEN: Serial Port Enable bit

1 = Serial port enabled (configures RX/DT and TX/CK pins as serial port pins)

0 = Serial port disabled (held in Reset)

bit 6 RX9: 9-bit Receive Enable bit

1 = Selects 9-bit reception

0 = Selects 8-bit reception

bit 5 SREN: Single Receive Enable bit

Asynchronous mode:

Don’t care.

Synchronous mode – Master:

1 = Enables single receive

0 = Disables single receive

This bit is cleared after reception is complete.

Synchronous mode – Slave:

Don’t care.

bit 4 CREN: Continuo us Receiv e Enab le bit

Asynchronous mode:

1 = Enables receiver

0 = Disables receiver

Synchronous mode:

1 = Enables continuous receive until enable bit, CREN, is cleared (CREN overrides SREN)

0 = Disables con t in uou s r ece iv e

bit 3 ADDEN: Address Detect Enable bit

Asynchronous mode 9-bit (RX9 = 1):

1 = Enables address detection, generates RCIF interrupt and loads RCREG when RX9D is set

0 = Disables address detection, all bytes are received and ninth bit can be used as parity bit

Asynchronous mode 8-bit (RX9 = 0):

Don’t care.

bit 2 FERR: Framing Error bit

1 = Framing error (can be updated by reading RCREG regi ster and receiving next valid byte)

0 = No framing error

bit 1 OERR: Overrun Error bit

1 = Overrun error (can be cleared by clearing bit CREN)

0 = No overrun error

bit 0 RX9D: 9th bit of Received Data

This can be address/data bit or a parity bit and must be calculated by user firmware.

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

U-0 R-1 U-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0

— RCIDL — SCKP BRG16 — WUE ABDEN

bit 7 bit 0

bit 7 Unimplemented: Re ad as ‘0’

bit 6 RCIDL: Receive Operation Idle Status bit

1 = Receiver is Idle

0 = Receiver is busy

bit 5 Unimplemented: Re ad as ‘0’

bit 4 SCKP: Synchronous Cl ock Polarity Select bi t

Asynchronous mode:

Unused in this mode.

Synchronous mode:

1 = Idle state for clock (CK) is a high level

0 = Idle state for clock (CK) is a low level

bit 3 BRG16: 16-bit Baud Rate Register Enable bit

1 = 16-bit Baud Rate Generator – SPBRGH and SPBRG

0 = 8-bit Baud Rate Generator – SPBRG only (Compatible mode), SPBRGH value ignored

bit 2 Unimplemented: Re ad as ‘0’

bit 1 WUE: Wake-up Enable bit

Asynchronous mode:

1 = EUSART will continue to sample the RX pin – interrupt generated on falling edge; bit

cleared in hardware on following rising edge

0 = RX pin not monitored or rising edge detected

Synchronous mode:

Unused in this mode.

bit 0 ABDEN: Auto-Baud Detect Enable bit

Asynchronous mode:

1 = Enable baud rate meas ure me nt on the next ch ara cte r – require s rec ept ion of a Sync by te

(55h); cleared in hardware upon completion

0 = Baud rate measurement disabled or completed

Synchronous mode:

Unused in this mode.

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

16.2 EUSART Baud Rate Generator

(BRG)

The BRG is a dedicated 8-bit or 16-bit generator, that

supports both the Asynchronous and Synchronous

modes of the EUSART. By default, the BRG operates

in 8-bit mode; setting the BRG16 bit (BAUDCTL<3>)

selects 16-bit mode.

The SPBRGH:SPBRG regi ste r p air co ntro ls the perio d

of a free running timer. In Asynchronous mode, bits

BRGH (TXSTA<2>) and BRG16 also control the baud

rate. In Synchronous mode, bit BRGH is ignored.

Table 16-1 shows the formula for computation of the

baud rate for different EUSART modes which only

apply in Master mode (internally generated clock).

Given the desired baud rate and FOSC, the nearest

integer value for the SPBRGH:SPBRG registers can be

calculated u sing the f ormulas in Table 16-1. From this,

the erro r in baud rate can be determine d. An example

calculation is shown in Example 16-1. Typical baud

rates and error values for the various asynchronous

modes are shown in Table 16-2. It may be

advantageous to use the high baud rate (BRGH = 1),

or the 16-bit BRG to reduce the baud rate error, or

achiev e a slow bau d rate for a fast osc illato r frequ ency.

Writing a new value to the SPBRGH:SPBRG registers

causes the BRG timer to be reset (or cleared). This

ensures the BRG does not wait for a timer overflow

before outputting the new baud rate.

16.2.1 POWER MANAGED MODE

OPERATION

The sys tem cl ock is used to generate the des ired bau d

rate; however, when a power managed mode is

entered, the clock source may be operating at a differ-

ent frequency than in PRI_RUN mode. In Sleep mode,

no clocks are present and in PRI_IDLE mode, the

primary clock sourc e cont inues to pr ovide clocks to the

Baud Rate Generator; however, in other power

managed modes, the clock frequency will probably

change. This may require the value in SPBRG to be

adjusted.

If the s ys tem c lo ck is changed duri ng an active r ece iv e

operation, a receive error or data loss may result. To

avoid this problem, check the status of the RCIDL bit

and make sure that the rece iv e o peration is Idl e b efo re

changing the system clock.

16.2.2 SAMPLING

The data on the RB4/AN6/RX/DT/KBI0 pin is sampled

three time s by a maj ority de tect cir cuit to de termine if a

high or a low level is present at the RX pin.

TABLE 16-1: BAUD RATE FORMULAS

EXAMPLE 16-1: CALCULATING BAUD RATE ERROR

Configuration Bits BRG/EUSART Mode Baud Rate Formula

SYNC BRG16 BRGH

000 8-bit/Asynchronous FOSC/[64 (n + 1)]

001 8-bit/Asynchronous FOSC/[16 (n + 1)]

010 16-bit/Asynchronous

011 16-bit/Asynchronous FOSC/[4 (n + 1)]10x 8-bit/Synchronous

11x 16-bit/Synchronous

Legend: x = Don’t care, n = value of SPBRGH:SPBRG register pair

For a device with FOSC of 16 MHz, desired bau d rat e of 9600, Asyn chronous mo de , 8-b it BRG :

Desired Baud Rate = FOSC/(64 ([SPBRGH:SPBRG] + 1))

Solving for SPBRGH:SPBRG:

X = ((FOSC/De s ired B aud Ra te)/64 ) – 1

= ((16 000000/96 00)/64) – 1

= [25.042] = 25

Ca l culated Baud Rate= 16000000/(64 (25 + 1))

= 9615

Error = (Calculated Baud Rate – Desired Baud Rate)/ D esi re d Ba ud Ra te

= (961 5 – 9600)/960 0 = 0. 16%

PIC18F1220/1320

TABLE 16-2: REGISTERS ASSOCIATED WITH BAUD RATE GENERATOR

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on

POR, BOR Value on all

other Resets

TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 -010 0000 -010

RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 -00x 0000 -00x

BAUDCTL —RCIDL —SCKP BRG16 —WUE ABDEN -1-1 0-00 -1-1 0-00

SPBRGH Baud Rate Generator Register High Byte 0000 0000 0000 0000

SPBRG Baud Rate Generator Register Low Byte 0000 0000 0000 0000

Legend: x = unknown, – = unimplemented, read as ‘0’. Shaded cells are not used by the BRG.

TABLE 16-3: BAUD RATES FOR ASYNCHRONOUS MODES

BAUD

RATE

(K)

SYNC = 0, BRGH = 0, BRG16 = 0

FOSC = 40.000 MHz FOSC = 20.000 MHz FOSC = 10.000 MHz FOSC = 8.000 MHz

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

0.3————————————

1.2 — — — 1.221 1.73 255 1.202 0.16 129 1201 -0.16 103

2.4 2.441 1.73 255 2.404 0.16 129 2.404 0.16 64 2403 -0.16 51

9.6 9.615 0.16 64 9.766 1.73 31 9.766 1.73 15 9615 -0.16 12

19.2 19.531 1.73 31 19.531 1.73 15 19.531 1.73 7 — — —

57.6 56.818 -1.36 10 62.500 8.51 4 52.083 -9.58 2 — — —

115.2 125.000 8.51 4 104.167 -9.58 2 78.125 -32.18 1 — — —

BAUD

RATE

(K)

SYNC = 0, BRGH = 0, BRG16 = 0

FOSC = 4.000 MHz FOSC = 2.000 MHz FOSC = 1.000 MHz

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

0.3 0.300 0.16 207 300 -0.16 103 300 -0.16 51

1.2 1.202 0.16 51 1201 -0.16 25 1201 -0.16 12

2.4 2.404 0.16 25 2403 -0.16 12 — — —

9.6 8.929 -6.99 6 — — — — — —

19.2 20.833 8.51 2 — — — — — —

57.6 62.500 8.51 0 — — — — — —

115.2 62.500 -45.75 0 — — — — — —

PIC18F1220/1320

BAUD

RATE

(K)

SYNC = 0, BRGH = 1, BRG16 = 0

FOSC = 40.000 MHz FOSC = 20.000 MHz FOSC = 10.000 MHz FOSC = 8.000 MHz

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

2.4 — — — — — — 2.441 1.73 255 2403 -0.16 207

9.6 9.766 1.73 255 9.615 0.16 129 9.615 0.16 64 9615 -0.16 51

19.2 19.231 0.16 129 19.231 0.16 64 19.531 1.73 31 19230 -0.16 25

57.6 58.140 0.94 42 56.818 -1.36 21 56.818 -1.36 10 55555 3.55 8

115.2 113.636 -1.36 21 113.636 -1.36 10 125.000 8.51 4 — — —

BAUD

RATE

(K)

SYNC = 0, BRGH = 1, BRG16 = 0

FOSC = 4.000 MHz FOSC = 2.000 MHz FOSC = 1.000 MHz

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

0.3 — — — — — — 300 -0.16 207

1.2 1.202 0.16 207 1201 -0.16 103 1201 -0.16 51

2.4 2.404 0.16 103 2403 -0.16 51 2403 -0.16 25

9.6 9.615 0.16 25 9615 -0.16 12 — — —

19.2 19.231 0.16 12 — — — — — —

57.6 62.500 8.51 3 — — — — — —

115.2 125.000 8.51 1 — — — — — —

BAUD

RATE

(K)

SYNC = 0, BRGH = 0, BRG16 = 1

FOSC = 40.000 MHz FOSC = 20.000 MHz FOSC = 10.000 MHz FOSC = 8.000 MHz

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

0.3 0.300 0.00 8332 0.300 0.02 4165 0.300 0.02 2082 300 -0.04 1665

1.2 1.200 0.02 2082 1.200 -0.03 1041 1.200 -0.03 520 1201 -0.16 415

2.4 2.402 0.06 1040 2.399 -0.03 520 2.404 0.16 259 2403 -0.16 207

9.6 9.615 0.16 259 9.615 0.16 129 9.615 0.16 64 9615 -0.16 51

19.2 19.231 0.16 129 19.231 0.16 64 19.531 1.73 31 19230 -0.16 25

57.6 58.140 0.94 42 56.818 -1.36 21 56.818 -1.36 10 55555 3.55 8

115.2 113.636 -1.36 21 113.636 -1.36 10 125.000 8.51 4 — — —

BAUD

RATE

(K)

SYNC = 0, BRGH = 0, BRG16 = 1

FOSC = 4.000 MHz FOSC = 2.000 MHz FOSC = 1.000 MHz

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

0.3 0.300 0.04 832 300 -0.16 415 300 -0.16 207

1.2 1.202 0.16 207 1201 -0.16 103 1201 -0.16 51

2.4 2.404 0.16 103 2403 -0.16 51 2403 -0.16 25

9.6 9.615 0.16 25 9615 -0.16 12 — — —

19.2 19.231 0.16 12 — — — — — —

57.6 62.500 8.51 3 — — — — — —

115.2 125.000 8.51 1 — — — — — —

TABLE 16-3: BAUD RATES FOR ASYNCHRONOUS MODES (CONTINUED)

PIC18F1220/1320

BAUD

RATE

(K)

SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1

FOSC = 40.000 MHz FOSC = 20.000 MHz FOSC = 10.000 MHz FOSC = 8.000 MHz

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

0.3 0.300 0.00 33332 0.300 0.00 16665 0.300 0.00 8332 300 -0.01 6665

1.2 1.200 0.00 8332 1.200 0.02 4165 1.200 0.02 2082 1200 -0.04 1665

2.4 2.400 0.02 4165 2.400 0.02 2082 2.402 0.06 1040 2400 -0.04 832

9.6 9.606 0.06 1040 9.596 -0.03 520 9.615 0.16 259 9615 -0.16 207

19.2 19.193 -0.03 520 19.231 0.16 259 19.231 0.16 129 19230 -0.16 103

57.6 57.803 0.35 172 57.471 -0.22 86 58.140 0.94 42 57142 0.79 34

115.2 114.943 -0.22 86 116.279 0.94 42 113.636 -1.36 21 117647 -2.12 16

BAUD

RATE

(K)

SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1

FOSC = 4.000 MHz FOSC = 2.000 MHz FOSC = 1.000 MHz

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

Actual

Rate

(K)

Error

SPBRG

value

(decimal)

0.3 0.300 0.01 3332 300 -0.04 1665 300 -0.04 832

1.2 1.200 0.04 832 1201 -0.16 415 1201 -0.16 207

2.4 2.404 0.16 415 2403 -0.16 207 2403 -0.16 103

9.6 9.615 0.16 103 9615 -0.16 51 9615 -0.16 25

19.2 19.231 0.16 51 19230 -0.16 25 19230 -0.16 12

57.6 58.824 2.12 16 55555 3.55 8 — — —

115.2 111.111 -3.55 8 — — — — — —

TABLE 16-3: BAUD RATES FOR ASYNCHRONOUS MODES (CONTINUED)

PIC18F1220/1320

16.2.3 AUTO-BAUD RATE DETECT

The Enhan ced USART module s up ports the autom ati c

detection and calibration of baud rate. This feature is

active only in Asynchronous mode and while the WUE

bit is clear.

The automatic baud rate measurement sequence

(Figure 16-1) begins whenever a S tart bit is received and

the ABDEN bit is set. The calculation is s elf-averaging .

In the Auto-Bau d Rate Detect (ABD) mode, the clock to

the BRG i s reversed. Rather than the BRG c locking the

incomi ng RX signal, the RX signal is tim ing the BRG. In

ABD mode, the internal Baud Rate Generator is used

as a coun ter to time the bit p eriod of the inco ming serial

byte stream.

Once th e ABDEN bit is set, th e st ate machine w ill c lear

the BRG an d look for a St art b it. The Au to-Baud Detect

must receive a byte with the value 55h (ASCII “U”,

which is also the LIN bus Sync character), in order to

calculate the proper bit rate. The measurement is t aken

over both a low and a high bit time in order to minim ize

any effects caused by asymmetry of the incoming sig-

nal. After a Start bit, the SPBRG begins counting up

using the preselected clock source on the first rising

edge of RX. After eight bits on the RX pin, or the fifth

rising edge, an accumulated value totalling the proper

BRG period is left in the SPBRGH:SPBRG registers.

Once the 5th edge is seen (should correspond to the

Stop bit), the ABDEN bit is automatically cleared.

While calibrating the baud rate period, the BRG

registers are clocked at 1/8th the preconfigured clock

rate. Note that the BRG clock will be configured by the

BRG16 and BRGH bits. Independent of the BRG16 bit

setting, bo th the SPBRG and SPBRGH will b e use d a s

a 16-bit counter. This allows the user to verify that no

carry occurred for 8-bit modes, by checking for 00h in

the SPBRGH register. Refer to Table 16-4 for counter

clock rates to the BRG.

While the ABD sequence takes place, the EUSART

state machine is held in Idle. The RCIF interrupt is set

once the fifth rising edge on RX is detected. The value

in the RCREG needs to be read to clear the RCIF

interrupt. RCREG content should be discarded.

16.2.4 RECEIVING A SYNC (AUTO-BAUD

RATE DETECT)

To receive a Sync (Auto-Baud Rate Detect):

1. Configure the EUSART for asynchronous receive.

TXEN should remain clear. SPBRGH:SPBRG

may be left as is. Th e cont rolle r sh ould opera te i n

either PRI_ RUN o r PRI _IDLE.

2. Enable RXIF interrupts. Set RCIE, PEIE, GIE.

3. Enable Auto-Baud Rate Detect. Set ABDEN.

4. When the next RCIF interrupt occurs, the

received baud rate has been measured. Read

RCREG to clear RCIF and discard. Check

SPBRGH:SPBRG for a valid value. The

EUSART is ready for normal communications.

Return from the interrupt. Allow the primary

clock to run (PRI_RUN or PRI_IDLE).

5. Process subsequent RCIF interrupts normally

as in asynchronous reception. Remain in

PRI_RUN or PRI_IDLE until communications

are complete.

TABLE 16-4: BRG COUNTER CLOCK

RATES

Note 1: It is up to the user to determine that the

incoming character baud rate is within the

range of the selected BRG clock source.

Some combinations of oscillator frequency

and EUSART baud rates are not possible

due to bit error rates. Overall system

timing and communication baud rates

must be taken into consideration when

using the Auto-Baud Rate Detection

feature.

BRG16 BRGH BRG Counter Clock

00 FOSC/512

01 FOSC/128

10 FOSC/128

11 FOSC/32

Note: During the ABD seq uence, SPBRG and

SPBRGH are both used as a 16-bit counter,

independent of BRG16 setting.

PIC18F1220/1320

FIGURE 16-1: AUTOMATIC BAUD RATE CALCULATION

16.3 EUSART Asynchronous Mode

The Asynchronous mode of operation is selected by

clearing the SYNC bit (TXSTA<4>). In this mode, the

EUSART uses st andard Non-Return-to-Zero (NRZ) for-

mat (o n e Start bi t , ei gh t or n ine da ta b i ts an d on e Stop

bit). The mos t common dat a format is 8 bit s. An on-chip

dedicated 8-bit/16-bit Baud Rate Generator can be

used to d erive st andard ba ud rate frequ encies fro m the

oscillator.

The EUSART transmits and receives the LSb first. The

EUSART’s transmitter and receiver are functionally

independent, but use the same data format and baud

rate. The Baud Rate Generator produces a clock, either

x16 or x64 of the bit shift rate, depending on the BRGH

and BRG16 bit s (TXSTA<2> and BAUDCTL<3>). Parity

is not supported by the hardware, but can be

implemented in softw are and stored as the 9 th data bit.

Asynchronous mode is available in all low-power

modes; it is available in Sleep mode only when auto-

wake-up o n Sync Break is en abled. Wh en in PRI_ IDLE

mode, no changes to the Baud Rate Generator values

are required; however, other low-power mode clocks

may operate at another frequency than the primary

clock . Therefore, the Baud Ra te Generator va lues may

need to be adjusted.

When operating in Asynchronous mode, the EUSART

module consists of the following important elements:

• Baud Rate Ge nerator

• Sampling Circuit

• Asynchronous Transmitter

• Asynchronous Receiver

• Auto-Wake-up on Sync Break Character

• 12-bit Break Character Transmit

• Auto-Baud Rate Detec tio n

16.3.1 EUSART ASYNCHRONOUS

TRANSMITTER

The EUSART transmitter block diagram is shown in

Figure 16-2. The heart of the transmitter is the T ransmit

(Serial) Shift Register (TSR). The shift register obtains

its data from the Read/Write Transmit Buffer register,

TXREG. The TXREG register is loaded with data in

software. The TSR register is not loaded until the Stop

bit has been transmitted from the previous load. As

soon as the Stop bit is transmitted, the TSR is loaded

with new data from t he TXREG register (if availabl e).

Once the TXREG register transfers the data to the TSR

empty and flag bit, TXIF (PIR1<4>), is set. This interrupt

can be enabled/disabled by setting/clearing enable bit,

TXIE (PIE1<4>). Flag bit, TXIF, will be se t, regardless of

the state of enable bit, TXIE, and cannot be cleared in

software. Flag bit, TXIF, is not cleared immediately upon

loading the Transmit Buffer register, TXREG. TXIF

becomes valid in the second instruction cycle following

the load instruction. Polling TXIF immediately following a

load of TXREG will return inva lid result s .

While flag bit, TXIF, indicates the status of the TXREG

status of the TSR register. Status bit, TRMT, is a read-

only bit, which is set when the TSR register is empty.

No interrupt logic is tied to this bit, so the user has to

poll this bit in order to determine if the TSR register is

empty.

BRG Value

RX pin

ABDEN bit

RCIF bit

Bit 0 Bit 1

(Interrupt)

Read

RCREG

BRG Clock

Start

Auto-Cleared

Set by User

XXXXh 0000h

Edge #1 Bit 2 Bit 3

Edge #2 Bit 4 Bit 5

Edge #3 Bit 6 Bit 7

Edge #4 Edge #5

001Ch

Note 1: The ABD sequence requires the EUSART module to be configured in Asynchronous mode and WUE = 0.

SPBRG XXXXh 1Ch

SPBRGH XXXXh 00h

Stop Bit

Note 1: The TSR register is not mapped in data

memory, so it is not available to the user.

2: Flag bit, TXIF, is set when enable bit,

TXEN, is set.

PIC18F1220/1320

To set up an Asynchronous Transmission:

1. Initialize the SPBRGH:SPBRG registers for the

appropriate baud rate. Set or clear the BRGH

and BRG16 bits, as required, to achieve the

desired baud rate.

2. Enable the asynchronous serial port by clearing

bit SYNC and setting bit SPEN.

3. If interrupts are desired, set enable bit TXIE.

4. If 9-bit transmission is desired, set transmit bit

TX9. Can be used as address/data bit.

5. Enable the transmission by setting bit TXEN,

which will also set bit TXIF.

6. If 9-bit transmission is selected, the ninth bit

should be loaded in bit TX9D.

7. Load data to the TXREG register (starts

transmission).

If using i nterrupt s, e nsure th at the GIE and PEIE bit s in

the INTCON register (INTCON<7:6>) are set.

FIGURE 16-2: EUSART TRANSMIT BLOCK DIAGRAM

FIGURE 16-3: ASYNCHRONOUS TRANSMISSION

TXIF

TXIE

Interrupt

TXEN Baud Rate CLK

SPBRG

Baud Rate Generator TX9D

MSb LSb

Data Bus

TXREG Register

TSR Register

(8) 0

TX9

TRMT SPEN

RB1/AN5/TX/CK/INT1 pin

Pin Buffer

and Cont rol

• • •

SPBRGH

BRG16

Word 1

Transmit Shift Reg

Start bit bit 0 bit 1 bit 7/8

Write to TXREG Word 1

BRG Output

(Shift Clock)

RB1/AN5/TX/

TXIF bit

(Transmit Buffer

Reg. Empty Flag)

TRMT bit

(Tran s mit Sh ift

Reg. Empty Flag)

1 TCY

CK/INT1 (pin) Stop bit

PIC18F1220/1320

FIGURE 16-4: ASYNCHRONOUS TRANSMISSION (BACK TO BACK)

TABLE 16-5: REGISTERS ASSOCIATED WITH ASYNCHRONOUS TRANSMISSION

Tra nsmit Shift Reg.

Write to TXREG

BRG Output

(Shift Clock)

RB1/AN5/TX/

TXIF bit

(Interrupt Reg. Flag)

TRMT bit

(Transmit Shift

Reg. Empty Flag)

Word 1 Word 2

Stop bit Start bit

Transmit Shift Reg.

Word 1 Word 2

bit 0 bit 1 bit 7/8 bit 0

Note: This timing diagram shows two consecutive transmissions.

1 TCY

CK/INT1 (pin) Start bit

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on

POR, BOR

Value on

all othe r

Resets

INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u

PIR1 —ADIF RCIF TXIF —CCP1IF TMR2IF TMR1IF -000 -000 -000 -000

PIE1 —ADIE RCIE TXIE —CCP1IE TMR2IE TMR1IE -000 -000 -000 -000

IPR1 —ADIP RCIP TXIP —CCP1IP TMR2IP TMR1IP -111 -111 -111 -111

RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 -00x 0000 -00x

TXREG EUSART Transmit Register 0000 0000 0000 0000

TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 0000 0010

BAUDCTL —RCIDL —SCKP BRG16 —WUE ABDEN -1-1 0-00 -1-1 0-00

SPBRGH Baud Rate Generator Register High Byte 0000 0000 0000 0000

SPBRG Baud Rate Generator Register Low Byte 0000 0000 0000 0000

Legend: x = unknown, – = unimplemented locations read as ‘0’. Shaded cells are not used for asynchron ous transmiss ion.

PIC18F1220/1320

16.3.2 EUSART ASYNCHRONOUS

RECEIVER

The receiver block diagram is shown in Figure 16-5.

The data is received on the RB4/AN6/RX/DT/KBI0 pin

and drives the data recovery block. The data recovery

block is actually a high-speed shifter, operating at x16

times the baud rate, whereas the main receive serial

shifter operates at the bit rate or at FOSC. This mode

would typically be used in RS-232 systems.

To set up an A synchrono us Re ception:

1. Initialize the SPBRGH:SPBRG registers for the

appropriate baud rate. Set or clear the BRGH

and BRG16 bits, as required, to achieve the

desired baud rate.

2. Enable the asynchronous serial port by clearing

bit SYNC and setting bit SPEN.

3. If interrupts are desired, set enable bit RCIE.

4. If 9-bit reception is desired, set bit RX9.

5. Enable the reception by setting bit CREN.

6. Flag bit, RCIF, will be set when reception is

complete and an interrupt will be generated if

enable bit R CI E was set.

7. Read the RCSTA register to get the 9th bit (if

enabled) and determine if any error occurred

during r eception.

8. Read the 8-bit received data by reading the

RCREG register.

9. If any error occurred, clear the error by clearing

enable bit C RE N.

10. If using int errupt s, ensu re that t he GIE a nd PEIE

bits in the INTCON register (INTCON<7:6>) are

set.

16.3.3 SETTING UP 9-BIT MODE WITH

ADDRESS DETECT

This mode would typically be used in RS-485 systems.

To set up an Asynchronous Reception with Address

Detect Enable:

1. Initialize the SPBRGH:SPBRG registers for the

appropriate baud rate. Set or clear the BRGH

and BRG16 bits, as required, to achieve the

desired baud rate.

2. Enable the asy nch ron ous seri al port by clearin g

the SYNC bit and setting the SPEN bit.

3. If in terrupts a re requ ired, se t the RCE N bit and

select the desired priori ty level with the RCIP bit.

4. Set the RX9 bit to enable 9-bit reception.

5. Set the ADDEN bit to enable address detect.

6. Enable reception by setting the CREN bit.

7. The RCIF bit will be set when reception is

complete. The interrupt will be Acknowledged if

the RCIE and GIE bits are set.

8. Read the RCSTA register to determine if any

error occurred during reception, as well as read

bit 9 of data (if app lic able).

9. Read RCREG to determine if the device is being

addressed.

10. If any error occurred, clear the CREN bit.

11. If the device has been addressed, clear the

ADDEN bit to allow all received data into the

receive buffer and interrupt the CPU.

FIGURE 16-5: EUSART RECEIVE BLOCK DIAGRAM

x64 Baud Rate CLK

Baud Rate Generato r

RB4/AN6/RX/DT/KBI0

Pin Buffer

and Control

SPEN

Data

Recovery

CREN OERR FERR

RSR Register

MSb LSb

RX9D RCREG Register FIFO

Interrupt RCIF

RCIE Data Bus

÷ 64

÷ 16

or Stop Start

(8) 7 1 0

RX9

• • •

SPBRGSPBRGH

BRG16

÷ 4

PIC18F1220/1320

To set up an Asynchronous Transmission:

1. Initialize th e SPBRG re gis te r for the ap prop ria te

baud rate. If a high-speed baud rate is desired,

set bit BRGH (see Section 16.2 “EUSART

Baud Rate Generator (BRG)”).

2. Enable the asynchronous serial port by clearing

bit SYNC and setting bit SPEN.

3. If interrupts are desired, set enable bit TXIE.

4. If 9-bit transmission is desired, set transmit bit

TX9. Can be used as address/data bit.

5. Enable the transmission by setting bit TXEN,

which will also set bit TXIF.

6. If 9-bit transmission is selected, the ninth bit

should be loaded in bit TX9D.

7. Load data to the TXREG register (starts

transmission).

If using i nterrupt s, e nsure th at the GIE and PEIE bit s in

the INTCON register (INTCON<7:6>) are set.

FIGURE 16-6: ASYNCHRONOUS RECEPTION

TABLE 16-6: REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION

Start

bit bit 7/8

bit 1bit 0 bit 7/8 bit 0Stop

bit

Start

bit Start

bit

bit 7/8 Stop

bit

RX (pin)

Reg

Rcv Buffer Reg

Rcv Shift

Read Rcv

Buffer Reg

RCREG

RCIF

(Interrupt Flag)

OERR bit

CREN

Word 1

RCREG Word 2

RCREG

Stop

bit

Note: This timing diagram shows three words appearing on the RX input. The RCREG (receive buffer) is read after

the third word, causing the OERR (overrun) bit to be set.

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on

POR, BOR

Value on

all other

Resets

INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u

PIR1 —ADIF RCIF TXIF —CCP1IF TMR2IF TMR1IF -000 -000 -000 -000

PIE1 —ADIE RCIE TXIE —CCP1IE TMR2IE TMR1IE -000 -000 -000 -000

IPR1 —ADIP RCIP TXIP —CCP1IP TMR2IP TMR1IP -111 -111 -111 -111

RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 000x 0000 000x

RCREG EUSART Receive Register 0000 0000 0000 0000

TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 0000 0010

BAUDCTL — RCIDL —SCKP BRG16 — WUE ABDEN -1-1 0-00 -1-1 0-00

SPBRGH Baud Rate Generator Register High Byte 0000 0000 0000 0000

SPBRG Baud Rate Generator Register Low Byte 0000 0000 0000 0000

Legend: x = unknown, – = unimplemented locations read as ‘0’. Shaded cells are not used for asynchronous reception.

PIC18F1220/1320

16.3.4 A UTO-WAKE-UP ON SYNC BREAK

CHARACTER

During Sleep mode, all clocks to the EUSART are

suspended. Because of this, the Baud Rate Generator

is inactive and a proper byte reception cannot be per-

formed. Th e auto-wak e-up feature al lows the cont roller

to wake-up due to activity on the RX/DT line while the

EUSART is operating in Asynchronous mode.

The auto-wake-up feature is enabled by setting the

WUE bit (BAUDCTL<1 >). Onc e s et, the typ ical rec eiv e

sequence on RX/DT is disabled and the EUSART

remains in an Idle state, mon itoring for a wake-up event

independent of the CPU mode. A wake-up event con-

sist s of a hig h-to-low t ransition on the RX/ DT line. (This

coinc ides wi th the star t of a Syn c Break or a Wake -up

Signal character for the LIN protocol.)

Following a wake-up event, the module generates an

RCIF interrupt. The interrupt is generated synchro-

nously to the Q clocks in normal operating modes

(Figure 16-7) and asynchronously if the device is in

Sleep mode (Figure 16-8). The interrupt condition is

cleared by reading the RCREG register.

The WUE bit is automatically cleared once a low- to-high

transition is observed on the RX line, following the wake-

up event. At this point, the EUSART module is in Idle

mode and returns to normal operation. This signals to

the user that the Sync Break event is over.

16.3.4.1 Special Considerations Using

Auto-Wake-up

Since auto-wake-up functions by sensing rising edge

transitions on RX/DT, information with any state changes

before the Stop bit may signal a false end-of-character

and cause data or framing errors. To work properly,

therefore, the initial character in the transmission must

be all ‘0’s. This can be 00h (8 bytes) for standard RS-232

devices, or 000h (12 bit s) for LIN bus.

Oscillator start-up time must also be considered,

especially in applications using oscillators with longer

start-up intervals (i.e., LP, XT or HS/PLL mode). The

Sync Break (or Wake-up Signal) character must be of

sufficient length and be followed by a sufficient period,

to allow enough time for the selected oscillator to start

and provide proper initialization of the EUSART.

16.3.4.2 Special Considerations Using

the WUE Bit

The timing of WUE and RCIF events may cause some

confusion when it comes to determining the validity of

receive d data. As noted , setting the WUE bit pl aces the

EUSART in an Idle mode. The wake-up event causes

a receiv e interrupt by setting th e RCIF bit. The WU E bit

is cleared after this when a rising edge is seen on RX/

DT. The interrupt condition is then cleared by reading

the RCREG register . Ordinarily, the dat a in RCREG will

be dummy data and should be discarded.

The fact that the WUE bit has been cleared (or is still

set) and the RCIF flag is set should not be used as an

indicator of the integrity of the data in RCREG. Users

should consider implementing a parallel method in

firmware to verify received data integrity.

To assu re th at n o act ual data is los t, che ck th e RCI DL

bit to ve rify th at a receive ope rati on is not in proces s. If

a receive operation is not occurring, the WUE bit may

then be set just prior to entering the Sleep mode.

FIGURE 16-7: AUTO-WAKE-UP BIT (WUE) TIMINGS DURING NORMAL OPERATION

FIGURE 16-8: AUTO-WAKE-UP BIT (WUE) TIMINGS DURING SLEEP

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

OSC1

WUE b i t

RX/DT Line

RCIF Cleared due to User Read of RCREG

Note 1: The EUSART remains in Idle while the WUE bit is set.

Bit Set by User Clear ed by hard w ar e

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

OSC1

WUE bit

RX/DT Line

RCIF Cleared due to User Read of RCREG

Note 1: If the wake-up event requires a long oscillator warm-up time, the WUE bit may be cleared while the primary clock is still starting.

2: The EUSART remains in Idle while the WUE bit is set.

Sleep En ds

Enters Sleep

Bit Set by User Cleared by hardware

Note 1

PIC18F1220/1320

16.3.5 BREAK CHARACTER SEQUENCE

The Enhanced USART module has the capability of

sending the special Break character sequences that

are required by the LIN bus standard. The Break char-

acter trans mit co nsist s of a Start bit, fol lowed by twelve

‘0’ bits and a Stop bit. The Frame Break character is

sent whene ve r the SEN DB an d TXEN bi t s (TXSTA<3>

and TXSTA<5>) are set while the Transmit Shift

written to TXREG will be ignored and all ‘0’s will be

transmitted.

The SENDB bit i s automaticall y reset by ha rdware after

the correspon din g Stop bit is s ent. This al lo w s the us er

to preloa d the trans mit FIFO with the n ext transm it byte

following the Break character (typically, the Sync

character in the LIN specification).

Note that the data value written to the TXREG for the

Break ch aracter is ignored. Th e write si mply se rves the

purpose of initiating the proper sequence.

The TRMT bit indicates when the transmit operation is

active or Idle, just as it does during normal transmis-

sion. See Figure 16-9 for the timing of the Break

character sequence.

16.3.5.1 Transmitting A Break Signal

The Enhanced USART module has the capability of

sendin g the Break si gnal that is required by th e LIN bus

standard. The Break signal consists of a Start bit,

followed by twelve ‘0’ bits and a S top bit. The Break sig-

nal is sent whenever the SENDB (TXSTA<3>) and

TXEN (TXSTA<5>) bits are set and TXREG is loaded

with data. The data written to TXREG will be ignored

and all ‘0’s will be transmitted.

SENDB is autom atical ly clea red by hardw are whe n the

Break signal has been sent. This allows the user to

preload the transmit FIFO with the next transmit byte

following the Break character (typically, the Sync

character in the LIN specification).

The TRMT bit indicates when the transmit operation is

active or Idle, just as it does during normal

transmission.

To send a Break Signal:

1. Configure the EUSART for asynchronous trans-

missions (steps 1-5). Initialize the SPBRG register

for the appropriate baud rate. If a high-speed baud

rate is desired, set bit BRGH (see Section 16.2

“EUSAR T Bau d Rate Gene rator ( BRG)” ).

2. Enable the asynchronous serial port by clearing

bit SYNC and setting bit SPEN.

3. If interrupts are desired, set enable bit TXIE.

4. If 9-bit transmission is desired, set transmit bit

TX9. Can be used as address/data bit.

5. Enable the transmission by setting bit TXEN,

which will also set bit TXIF.

6. Set the SENDB bit.

7. Load a byte into TXREG. This triggers sending a

Break signal. The Break signal is complete

when TRMT is set. SEN DB will also be cleared.

See Figure 16-9 for the timing of the Break signal

sequence.

16.3.6 RECEIVIN G A BREAK CHARACTER

The Enhanced USART module can receive a Break

character in two ways.

The first method forces configuration of the baud rate

at a freq uency of 9/ 13 the typi cal spee d. This allow s for

the Stop bit transition to be at the correct sampling

location (12 bits for Break versus Start bit and 8 data

bits for typic al dat a ) .

The second method uses the auto-wake-up feature

describ ed in Section 16.3.4 “Auto-Wake-up on Sync

Break Character”. By enabling this feature, the

EUSART will sample the next two transitio ns on RX/DT,

cause an RCIF interru pt and receiv e the n ext da ta byte

followed by another interrupt.

Note that following a Break character, the user will

typically want to enable the Auto-Baud Rate Detect

feature. Fo r both methods, th e user can set the ABD bit

before placing the EUSART in its Sleep mode.

16.3.6.1 Transmitting a Break Sync

The following sequence will send a message frame

header made up of a Break, followed by an auto-baud

Sync byte. This s equence is ty pical of a LIN bus master.

1. Configure the EUSART for the desired mode.

2. Set the TXEN and SENDB bits to set up the

Break character.

3. Load the TXREG with a dummy character to

initiate transmission (the value is ignored).

4. Write ‘55h’ to TXREG to load the Sync character

into the transm it FIFO buf fe r.

5. After the Break has been sent, the SENDB bit is

reset by hardware. The Sync character now

transmits in the preconfigured mode. When the

TXREG becomes empty, as indicated by the

TXIF, the next data byte can be written to TXREG.

PIC18F1220/1320

16.3.6.2 Receiving a Break Sync

To receive a Break Sync:

1. Configure the EUSART for asynchronous

transmit and receive. TXEN should remain

clear. SPBRGH:SPBRG may be left as is.

2. Enable auto-wake-up. Set WUE.

3. Enable RXIF interrupts. Set RCIE, PEIE, GIE.

4. The controller may be placed in any power

managed mode.

5. An RCIF will be generated at the beginning of

the Break s ignal. Whe n the interrupt i s received,

read RCREG to clear RCIF and discard. Allow

the controller to return to PRI_RUN mode.

6. Wai t for the RX line to go high at the end of the

Break sig nal. Wait for any of the foll owin g: WUE

to clear automatically (poll), RB4/RX to go high

(poll) or for RBIF to be set (poll or interrupt). If

RBIF is used, chec k to be sure that RB4/RX is

high before continuing.

7. Enable Auto-Baud Rate Detect. Set ABDEN.

8. Return from the interrupt. Allow the primary

clock to start and stabilize (PRI_RUN or

PRI_IDLE).

9. When the next RCIF interrupt occurs, the

received baud rate has been measured. Read

RCREG to clear RCIF and discard. Check

SPBRGH:SPBRG for a valid value. The

EUSART is ready for normal communications.

Return from the interrupt. Allow the primary

clock to run (PRI_RUN or PRI_IDLE).

10. Process subsequent RCIF interrupts normally

as in asynchronous reception. TXEN should

now be set if transmissions are needed. TXIF

and TXIE may be set if transmit interrupts are

desired. Remain in PRI_RUN or PRI_IDLE until

commu nication s are comp lete. C lear TXEN and

return to step 2.

FIGURE 16-9: SEND BREAK CHARACTER SEQUENCE

Write to TXREG

BRG Output

(Shift Clock)

Start Bit Bit 0 Bit 1 Bit 11 Stop Bit

Break

TXIF bit

TX (pin)

TRMT bit

SENDB

Dummy Write

PIC18F1220/1320

16.4 EUSART Synchronous Master

Mode

The Synchronous Master mode is entered by setting

the CSRC bit (TXSTA<7>). In this mode, the data is

transmitted in a half-duplex manner (i.e., transmission

and reception do not occur at the same time). When

transmitting data, the reception is inhibited and vice

versa. Synchronous mode is entered by setting bit,

SYNC (TXSTA<4>). In addition, enable bit, SPEN

(RCSTA<7>), i s se t i n o rder to configure the R B1/ AN 5/

TX/CK/INT1 and RB4/AN6/RX/DT/KBI0 I/O pins to CK

(clock) and DT (data) lines, respectively.

The Master mode indicates that the processor trans-

mits the master clock on the CK line. Clock polarity is

selected with the SCKP bit (BAUDCTL<5>); setting

SCKP sets the Idle state on CK as high, while clearing

the bit se ts t he Idle st ate as low. This opt ion is prov ided

to support Microwire devices with this module.

16.4.1 EUSART SYNCHRONOUS MASTER

TRANSMISSION

The EUSART transmitter block diagram is shown in

Figure 16-2. The heart of the transmitter is the Transmit

(Serial) Shift Register (TSR). The shift register obtains

its data from the Read/Write Transmit Buffer register,

TXREG. The TXREG register is loaded with data in

software. The TSR register is not loaded until the last

bit has been transmitted from the previous load. As

soon as the last bit is transmitted, the TSR is loaded

with new data from the TXREG (if available).

Once the TXR EG register tr ansfers the dat a to the TSR

and interrupt bit, TXIF (PIR1<4>), is set. The interrupt

can be enabled/disabled by setting/clearing enable bit,

TXIE (PIE1<4>). Flag bit, TXIF, will be set, regardless

of the state of enable bit, TXIE and cannot be cleared

in software. It will reset only when new data is loaded

into the TXREG regis ter.

While flag bit, TXIF, indicates the status of the TXREG

status of the TSR register. TRMT is a read-only bit,

which is set when the TSR is em pty. No interrupt logic is

tied to this bit, so the user has to poll this bit in order to

determine if the TSR register is empty. The TSR is not

mapped in data memory , so it is not available to the user .

To set up a Synchronous Master Transmission:

1. Initialize the SPBRGH:SPBRG registers for the

appropriate baud rate. Set or clear the BRGH

and BRG16 bits, as required, to achieve the

desired baud rate.

2. Enable the synchronous master serial port by

setting bits SYNC, SPEN and CSRC.

3. If interrupts are desired, set enable bit TXIE.

4. If 9-bit transmission is desired, set bit TX9.

5. Enable the transmission by setting bit TXEN.

6. If 9-bit transmission is selected, the ninth bit

should be loaded in bit TX9D.

7. S tart transmission by loading da ta to the TXREG

8. If using interrup ts, ensu re that the GIE and PEIE

bits in the INTCON register (INTCON<7:6>) are

set.

FIGURE 16-10: SYNCHRONOUS TRANSMISSION

bit 0 bit 1 bit 7

Word 1

Q1Q2 Q3Q4 Q1 Q2Q3 Q4 Q1Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1Q2 Q3 Q4 Q3 Q4 Q1 Q2 Q3Q4 Q1Q2 Q3Q4 Q1 Q2Q3 Q4 Q1 Q2Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4

bit 2 bit 0 bit 1 bit 7

RB4/AN6/RX/

RB1/AN5/TX/

Write to

TXREG Reg

TXIF bit

(Interrupt Flag)

TXEN b it ‘1’ ‘1’

Word 2

TRMT bit

Write Word 1 Write Word 2

Note: Sync Master mode, SPB RG = 0, continuous transmission of two 8-bit words.

DT/KBI0 pin

CK/INT1 pin

RB1/AN5/TX/

CK/INT1 pin

(SCKP = 0)

(SCKP = 1)

PIC18F1220/1320

FIGURE 16-11: SYNCHRONOUS TRANSM ISSION (THROUGH TXEN)

TABLE 16-7: REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER TRANSMISSION

RB4/AN6/RX/DT /KBI 0 pin

RB1/AN5/TX/CK/ INT1 pin

Write to

TXREG reg

TXIF bit

TRMT bit

bit 0 bit 1 bit 2 bit 6 bit 7

TXEN bit

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Va lue on

POR, BOR

Value on

all other

Resets

INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u

PIR1 —ADIF RCIF TXIF —CCP1IF TMR2IF TMR1IF -000 -000 -000 -000

PIE1 —ADIE RCIE TXIE —CCP1IE TMR2IE TMR1IE -000 -000 -000 -000

IPR1 —ADIP RCIP TXIP —CCP1IP TMR2IP TMR1IP -111 -111 -111 -111

RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 -00x 0000 -00x

TXREG EUSART Transmit Register 0000 0000 0000 0000

TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 0000 0010

BAUDCTL —RCIDL — SCKP BRG16 —WUE ABDEN -1-1 0-00 -1-1 0-00

SPBRGH Baud Rate Generator Register High Byte 0000 0000 0000 0000

SPBRG B aud Rate Generator Register Low Byte 0000 0000 0000 0000

Legend: x = unknown, – = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master transmission.

PIC18F1220/1320

16.4.2 EUSART SYNCHRONOUS MASTER

RECEPTION

Once Synchronous mode is selected, reception is

enabled by setting either the Single Receive Enable bit,

SREN (RCSTA<5>), or the Continuous Receive

Enable bit, CREN (RCSTA<4>). Data is sampled on the

RB4/AN6/RX/DT/KBI0 pin on the falling edge of the

clock.

If enable bit, SREN, is set, only a single word is

received. If enable bit, CREN, is set, the reception is

continuous until CREN is cleared. If both bits are set,

then CRE N tak es prece den ce .

To set up a Synchronous Master Reception:

1. Initialize the SPBRGH:SPBRG registers for the

appropriate baud rate. Set or clear the BRGH

and BRG16 bits, as required, to achieve the

desired baud rate.

2. Enable the synchronous master serial port by

setting bits SYNC, SPEN and CSRC.

3. Ensure bits CREN and SREN are clear.

4. If interrupts are desired, set enable bit RCIE.

5. If 9-bit reception is desired, set bit RX9.

6. If a single reception is required, set bit SREN.

For continuous reception, set bit CREN.

7. Interrupt flag bit, RCIF, will be set when reception

is complete and an interrupt will be generated if

the enable bit, RCIE, was set.

8. Read the RCSTA register to get the 9th bit (if

enabled) and determine if any error occurred

during reception.

9. Read the 8-bit received data by reading the

RCREG register.

10. If any error occurred, clear the error by clearing

bit CREN.

11. If using interrup ts, ensure tha t the GIE and PEIE

bits in the INTCON register (INTCON<7:6>) are

set.

FIGURE 16-12: SYNCHRONOUS RECEPTION (MASTER MODE, SREN)

CREN bit

RB4/AN6/RX/

RB1/AN5/TX/

Write to

bit SREN

SREN bit

RCIF bit

(Interrupt)

Read

RXREG

Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q2 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1Q2 Q3 Q4 Q1Q2 Q3 Q4Q1 Q2Q3 Q4 Q1 Q2 Q3 Q4

‘

’

bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7

‘

’

Q1 Q2 Q3 Q4

Note: Timing diagram demonstrates Sync Mas ter mode with bit SREN = 1 and bit BRGH = 0.

RB1/AN5/TX/

CK/INT1 pin

DT/KBI0 pin

(SCKP = 0)

(SCKP = 1)

PIC18F1220/1320

TABLE 16-8: REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on

POR, BOR

Value on

all other

Resets

INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u

PIR1 —ADIF RCIF TXIF —CCP1IF TMR2IF TMR1IF -000 -000 -000 -000

PIE1 —ADIE RCIE TXIE —CCP1IE TMR2IE TMR1IE -000 -000 -000 -000

IPR1 —ADIP RCIP TXIP —CCP1IP TMR2IP TMR1IP -111 -111 -111 -111

RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 000x 0000 000x

RCREG EUSART Recei ve Register 0000 0000 0000 0000

TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 0000 0010

BAUDCTL — RCIDL — SCKP BRG16 —WUE ABDEN -1-1 0-00 -1-1 0-00

SPBRGH Baud Rate Generator Register High Byte 0000 0000 0000 0000

SPBRG Baud Rate Generator Register Low Byte 0000 0000 0000 0000

Legend: x = unknown, – = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.

PIC18F1220/1320

16.5 EUSART Synchronous

Slave Mode

Synchronous Slave mode is entered by clearing bit,

CSRC (TXSTA<7>). This mode differs from the

Synchronous Master mode in that the shift clock is

supplied externally at the RB1/AN5/TX/CK/INT1 pin

(instead of being supplied internally in Master mode).

This allows the device to transfer or receive data while

in any low-power mode.

16.5.1 EUSART SYNCHRONOUS

SLAVE TRANSMIT

The operation of the Synchronous Master and Slave

modes are identical, except in the case of the Sleep

mode.

If two words are written to the TXREG and then the

SLEEP instruction is executed, the following will occur:

a) The first word will immediately transfer to the

TSR register and transmit.

b) The second word will remain in the TXREG

c) Flag bit, TXIF, will not be set.

d) When the first word has been shifted out of TSR,

the TXREG register will transfer the second

word to the TSR and flag bit, TXIF, will now be

set.

e) If enable bit, TXIE, is set, the interrupt will wake

the chip from Sleep. If the global interrupt is

enabled , the p rog ram wil l bran ch to the in terrupt

vector.

To set up a Synchronous Slave Transmission:

1. Enable the synchronous slave serial port by

setting bits SYNC and SPEN and clearing bit

CSRC.

2. Clear bits CREN and SREN.

3. If interrupts are desired, set enable bit TXIE.

4. If 9-bit transmission is desired, set bit TX9.

5. Enable the transmission by setting enable bit

TXEN.

6. If 9-bit transmission is selected, the ninth bit

should be loaded in bit TX9D.

7. S tart transmission by loading da ta to the TXREG

8. If using interrup ts, ensu re that the GIE and PEIE

bits in the INTCON register (INTCON<7:6>) are

set.

TABLE 16-9: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on

POR, BOR

Valu e on

all othe r

Resets

INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u

PIR1 —ADIF RCIF TXIF —CCP1IF TMR2IF TMR1IF -000 -000 -000 -000

PIE1 —ADIE RCIE TXIE —CCP1IE TMR2IE TMR1IE -000 -000 -000 -000

IPR1 —ADIP RCIP TXIP —CCP1IP TMR2IP TMR1IP -111 -111 -111 -111

RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 000x 0000 000x

TXREG EUSART Transmit Register 0000 0000 0000 0000

TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 0000 0010

BAUDCTL —RCIDL — SCKP BRG16 —WUE ABDEN -1-1 0-00 -1-1 0-00

SPBRGH Baud Rate Generator Register High Byte 0000 0000 0000 0000

SPBRG B aud Rate Generator Register Low Byte 0000 0000 0000 0000

Legend: x = unknown, – = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave transmission.

PIC18F1220/1320

16.5.2 EUSART SYNCHRONOUS SLAVE

RECEPTION

The operation of the Synchronous Master and Slave

modes is identical, except in the case of Sleep, or any

Idle mode and bit SREN, which is a “don’t care” in

Slave mode.

If receive is enabled by setting the CREN bit prior to

entering Sleep or any Idle mode, then a word may be

received while in this low-power mode. Once the word

is received, the RSR registe r will transfer the data to the

RCREG register; if the RCIE enable bit i s set, t he inter-

rupt generated will wake the chip from low-power

mode. If the global interrupt is enabled, the pro gram will

branch to the interrupt vector.

To set up a Synchronous Slave Reception:

1. Enable the synchronous master serial port by

setting bits SYNC and SPEN and clearing bit

CSRC.

2. If interrupts are desired, set enable bit RCIE.

3. If 9-bit reception is desired, set bit RX9.

4. To enable reception, set enable bit CREN.

5. Flag bit, RCIF, will be set when reception is

complete. An interrupt will be generated if

enable bit, RCIE, was set.

6. Read the RCSTA register to get the 9th bit (if

enabled) and determine if any error occurred

during reception.

7. Read the 8-bit received data by reading the

RCREG register.

8. If any error occurred, clear the error by clearing

bit CREN.

9. If using interrup ts, ensu re that the GIE and PEIE

bits in the INTCON register (INTCON<7:6>) are

set.

TABLE 16-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Va lue on

POR, BOR

Value on

all othe r

Resets

INTCON GIE/GIEH PEIE/GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 000x 0000 000u

PIR1 —ADIF RCIF TXIF —CCP1IF TMR2IF TMR1IF -000 -000 -000 -000

PIE1 —ADIE RCIE TXIE —CCP1IE TMR2IE TMR1IE -000 -000 -000 -000

IPR1 —ADIP RCIP TXIP —CCP1IP TMR2IP TMR1IP -111 -111 -111 -111

RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 000x 0000 000x

RCREG EUSART Receive Register 0000 0000 0000 0000

TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 0000 0010

BAUDCTL — RCIDL —SCKPBRG16—WUE ABDEN -1-1 0-00 -1-1 0-00

SPBRGH Baud Rate Generator Register High Byte 0000 0000 0000 0000

SPBRG Baud Rate Generator Register Low Byte 0000 0000 0000 0000

Legend: x = unknown, – = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave reception.

PIC18F1220/1320

NOTES:

PIC18F1220/1320

17.0 10-BIT ANALOG-TO-DIGITAL

CONVERTER (A/D) MODULE

The Analog-to-Digital (A/D) converter module has

seven inputs for the PIC18F1220/1320 devices. This

module allows conversion of an analog input signal to

a corresponding 10-bit digital number.

A new feature for the A/D converter is the addition of

programmable acquisition time. This feature allows the

user to select a new channel for conversion and to set

the GO/DONE b it immedia tely. When th e GO/DONE bit

is set, the selected channel is sampled for the pro-

grammed acquisition time before a conversion is actu-

ally started. This removes the firmware overhead that

may have been required to allow for an acquisition

(sampl ing) period (see Register 17-3 and Section 17.3

“Selecting and Configuring Automatic Acquisition

Time”).

The module has five registers:

• A/D Result High Register (ADRESH)

• A/D Result Low Register (ADRESL)

• A/D Control Register 0 (ADCON0)

• A/D Control Register 1 (ADCON1)

• A/D Control Register 2 (ADCON2)

The ADCON0 register, shown in Register 17-1,

controls the operation of the A/D module. The

ADCON1 register, shown in Register 17-2, configures

the functions of the port pins. The ADCON2 register,

shown in Register 17-3, configures the A/D clock

source, p rogrammed acquisi tion time and justification.

R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

VCFG1 VCFG0 — CHS2 CHS1 CHS0 GO/DONE ADON

bit 7 bit 0

bit 7-6 VCFG<1:0>: Voltage Reference Configuration bits

bit 5 Unimplemented: Read as ‘0’

bit 4-2 CHS2:CHS0: Analog Channel Select bits

000 = Channel 0 (AN0)

001 = Channel 1 (AN1)

010 = Channel 2 (AN2)

011 = Channel 3 (AN3)

100 = Channel 4 (AN4)

101 = Channel 5 (AN5)

110 = Channel 6 (AN6)

111 = Unimplemented(1)

bit 1 GO/DONE: A/D Conve rsion Status bit

When ADON = 1:

1 = A/D conversion in progress

0 = A/D Idle

bit 0 ADON: A/D On bit

1 = A/D converter module is enabled

0 = A/D converter module is disabled

Note 1: Performing a conversion on unimplemented channels returns full-scale results.

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

A/D V REF+A/D VREF-

00 AVDD AVSS

01 External VREF+AVSS

10 AVDD External VREF-

11 External VREF+ External VREF-

PIC18F1220/1320

U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

— PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0

bit 7 bit 0

bit 7 Unimplemented: Read as ‘0’

bit 6 PCFG6: A/D Port Configuration bit – AN6

1 = Pin configured as a digital port

0 = Pin configured as an analog channel – digital input disabled and reads ‘0’

bit 5 PCFG5: A/D Port Configuration bit – AN5

1 = Pin configured as a digital port

0 = Pin configured as an analog channel – digital input disabled and reads ‘0’

bit 4 PCFG4: A/D Port Configuration bit – AN4

1 = Pin configured as a digital port

0 = Pin configured as an analog channel – digital input disabled and reads ‘0’

bit 3 PCFG3: A/D Port Configuration bit – AN3

1 = Pin configured as a digital port

0 = Pin configured as an analog channel – digital input disabled and reads ‘0’

bit 2 PCFG2: A/D Port Configuration bit – AN2

1 = Pin configured as a digital port

0 = Pin configured as an analog channel – digital input disabled and reads ‘0’

bit 1 PCFG1: A/D Port Configuration bit – AN1

1 = Pin configured as a digital port

0 = Pin configured as an analog channel – digital input disabled and reads ‘0’

bit 0 PCFG0: A/D Port Configuration bit – AN0

1 = Pin configured as a digital port

0 = Pin configured as an analog channel – digital input disabled and reads ‘0’

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0

ADFM — ACQT2 ACQT1 ACQT0 ADCS2 ADCS1 ADCS0

bit 7 bit 0

bit 7 ADFM: A/D Result Format Select bit

1 = Right justified

0 = Left justified

bit 6 Unimplemented: Re ad as ‘0’

bit 5-3 ACQT2:ACQT0: A/D Acquis iti on Time Selec t bits

000 = 0 TAD(1)

001 = 2 TAD

010 = 4 TAD

011 = 6 TAD

100 = 8 TAD

101 = 12 TAD

110 = 16 TAD

111 = 20 TAD

bit 2-0 ADCS2:ADCS0: A/D Conversion Clock Select bits

000 = FOSC/2

001 = FOSC/8

010 = FOSC/32

011 = FRC (clock derived from A/D RC oscillator)(1)

100 = FOSC/4

101 = FOSC/16

110 = FOSC/64

111 = FRC (clock derived from A/D RC oscillator)(1)

Note: If the A/D FRC clock source is selected, a delay of one TCY (instruction cycle) is

added bef ore the A/D c lock st arts. This allows the SLEEP inst ruction to be executed

before starting a conversion.

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

The analog reference voltage is software selectable to

either the device’s positive and negative supply voltage

(AVDD and AVSS), or the voltage level on the

RA3/AN3/VREF+ and RA2/AN2/VREF- pins.

The A/D converter has a unique feature of being able

to operate while the device is in Sleep mode. To oper-

ate in Sleep, th e A/D conv ersion clock must b e derive d

from the A/D’s internal RC oscillator.

The output of the sample and hold is the input into the

converter, which generates the result via successive

approximation.

A device Reset forces all registers to their Reset state.

This forces the A/D module to be turned off and any

conversion in progress is aborted.

Each port pin associated with the A/D converter can be

configured as an analog input, or as a digital I/O. The

ADRESH and ADRESL registers contain the result of

the A/D conversion. When the A/D conversion is com-

plete, the result is loaded into the ADRESH/ADRESL

registers, the GO/DONE bit (ADCON0 register) is

cleared and A/D Interrupt Flag bit, ADIF, is set. The block

diagram of the A/D module is s hown in Figure 17-1.

FIGURE 17-1: A/D BLOCK DIAGRAM

(Input Voltage)

VAIN

VREFH

Reference

Voltage

AVDD

VCFG1:VCFG0

CHS2:CHS0

AN6(1)

AN5

AN4

AN3/VREF+

AN2/VREF-

AN1

AN0

111

110

101

100

011

010

001

000

10-bit

Converter

VREFL

AVSS

A/D

Note 1: I/O pins have diode protection to VDD and VSS.

AVDD

PIC18F1220/1320

The value in the ADRESH/ADRESL registers is not

modified for a Power-on Reset. The ADRESH/ADRESL

registers will contain unknown data after a Power-on

Reset.

After the A/D module has been configured as desired,

the sele cted channe l m ust be acquire d b efor e the con-

version is started. The analog input channels must

have their corresponding TRIS bits selected as an

input. To determine acquisition time, see Section 17.1

“A/D Acquisition Requirements”. After this acquisi-

tion time has elapsed, the A/D conversion can be

started. An acquisition time can be programmed to

occur bet ween setting th e GO/DONE bit an d the actual

start of the conversion.

To do an A/D Conversion:

1. Configure the A/D module:

• Config ure an alog pins, volt age refere nce a nd

digital I/O (ADCON1)

• Select A/D input channel (ADCON0)

• Select A/D acquisition time (ADCON2)

• Select A/D conversion clock (AD CON2)

• Turn on A/D module (ADCON0)

2. Configure A/D interrupt (if desired):

• Clear ADIF bit

• Set ADIE bit

• Set GIE bit

3. Wait the required acquisition time (if required).

4. Start conversion:

• Set GO/DONE bit (ADCON0 register)

5. Wait for A/D conversion to complete, by either:

• Polling for the GO/DONE bit to be cleared

• Waiting for the A/D interrupt

6. Read A/D Result registers (ADRESH:ADRESL);

clear bit, ADIF, if required.

7. For the next conversion, go to step 1 or step 2,

as required. The A/D conversion time per bit is

defined as TAD. A minimum wait of 2 TAD is

required before the next acquisition starts.

FIGURE 17-2: ANALOG INPUT MODEL

VAIN CPIN

Rs ANx

5 pF

VDD

VT = 0.6V

VT = 0.6V ILEAKAGE

RIC ≤ 1k

Sampling

Switch

SS RSS

CHOLD = 120 pF

VSS

Sampling Switch

567891011

(kΩ)

VDD

± 500 nA

Legend: CPIN = input capacitance

VT= threshold voltage

ILEAKAGE = leakage current at the pin due to

various junctions

RIC = interconnect resistance

SS = sampling switch

CHOLD = sample/hold capacitance (from DAC)

RSS = sam pling sw itch resistan ce

PIC18F1220/1320

17.1 A/D Acquisition Requirements

For the A/D converter to meet its specified accuracy,

the charge holding capacitor (CHOLD) must be allowed

to fully charge to the input channel voltage level. The

analog input model is shown in Figure 17-2. The

source impedance (RS) and the internal sampling

switch (RSS) impedance directly affect the time

required to charge the capacitor CHOLD. The sampling

switch (RSS) impedance va ries ov er the dev ice vol tag e

(VDD). The sour ce impedanc e af fects th e offse t voltag e

at the analog input (due to pin leakage current). The

maximum recommended impedance for analog

sources is 2.5 kΩ. After the analog input channel is

selected (changed), the channel must be sampled for

at least the minimum acquisition time before starting a

conversion.

To calculate the minimum acquisition time,

Equation 17-1 may be used. This equation assumes

that 1/2 LSb erro r is used (1024 step s for the A/D). The

1/2 LSb e rror is th e ma ximu m erro r a llowed fo r t he A/D

to meet its specified resolution.

Example 17-1 shows the calculation of the minimum

required acquisition time, TACQ. This calculation is

based on the following application system

assumptions:

CHOLD = 120 pF

Rs = 2.5 kΩ

Conversion Error ≤1/2 LSb

VDD =5V → RSS = 7 kΩ

Temperature = 50°C (system max.)

VHOLD = 0V @ time = 0

17.2 A/D VREF+ and VREF- References

If external voltage references are used instead of the

internal AVDD and AVSS sources, the source imped-

ance of the VREF+ and VREF- volta ge sour c e s must be

considered. During acquisition, currents supplied by

these sources are insignificant. However, during

conversion, the A/D module sinks and sources current

through the reference sources.

In order to maintain the A/D accuracy, the voltage

reference source impedances should be kept low to

reduce volt ag e cha nges. These volt age chan ges o ccur

as reference currents flow through the reference

source impedance. The maximum recommended

impedance of the VREF+ and VREF- external

reference voltage sources is 250Ω.

EQUATION 17-1: ACQUISITION TIME

EQUATION 17-2: A/D MINIMUM CHARGING TIME

EXAMPLE 17-1: CALCULATING THE MINIMUM REQUIRED ACQUISITION TIME

Note: When the conversion is started, the

holding cap ac itor i s di scon nected from the

input pin.

TACQ = Amplifier Settling Time + Holding Capacitor Charging Time + Temperature Coefficient

AMP + TC + TCOFF

VHOLD = (ΔVREF – (ΔVREF/2048)) • (1 – e(-TC/CHOLD(RIC + RSS + RS)))

TC = -(CHOLD)(RIC + RSS + RS) ln(1/2048)

TACQ =TAMP + TC + TCOFF

TAMP =5 μs

TCOFF = (Temp – 25ºC)(0. 05 μs/ºC)

(50ºC – 25º C)(0.05 μs/ºC)

1.25 μs

Temper at ure coeffici ent is on ly required for tem p e r atures > 25ºC. Below 25 ºC, TCOFF = 0 μs.

TC =-(CHOLD)(RIC + RSS + RS) ln(1/2047) μs

-(120 pF) (1 kΩ + 7 kΩ + 2.5 kΩ) ln(0.0004 883) μs

9.61 μs

TACQ =5 μs + 1.25 μs + 9.61 μs

12.86 μs

PIC18F1220/1320

17.3 Selecting and Configuring

Automatic Acquisition Time

The ADCON2 register allows the user to select an

acquisition time that occurs each time the GO/DONE

bit is set.

When the GO/DON E bit is set, sampling is stopped and

a conve rsion begins. Th e user is responsi ble for ens ur-

ing the required acquisition time has passed between

selecting the desired input channel and setting the

GO/DONE bit. This occurs when the ACQT2:ACQT0

bits (ADCON2<5 :3>) remai n in their Re set state (‘000’)

and is compatible with devices that do not offer

progra mmab le ac qui sition times.

If desired, the ACQT bits can be set to select a

programmable acquisition time for the A/D module.

When the GO/DONE bit is set, the A/D module contin-

ues to sample the input for the selected acquisition

time, th en automatic ally begins a conversio n. Since the

acquis iti on time is pro gram m ed, t here ma y be no need

to wait for an acquisition time between selecting a

channel and setting the GO/DONE bit.

In either case, when the conversion is completed, the

GO/DONE bit is cleared, the ADIF flag is set and the

A/D begins sampling the currently selected channel

again. If an acquisition time is programmed, there is

nothing to indicate if the acquisition time has ended or

if the conversion has begun.

17.4 Selecting the A/D Conversion

Clock

The A/D conversion time per bit is defined as TAD. The

A/D c on vers ion re qui res 11 TAD per 10-bit conversion.

The source of the A/D conversion clock is software

selectable. There are seven possible options for TAD:

•2 T

OSC

•4 TOSC

•8 TOSC

•16 TOSC

•32 TOSC

•64 TOSC

• Intern al RC osc il lat or

For correct A/D conversions, the A/D conversion clock

(TAD) must be as sh ort as possible, bu t greater than the

minimum TAD (approximately 2 μs, see parameter 130

for more information).

Table 17-1 shows the resultant TAD t im es der i ve d fr o m

the device operating frequencies and the A/D clock

source selected.

TABLE 17-1: TAD vs. DEVICE OPERATING FREQUENCIES

AD Clock Source (TAD) Maximum Device Frequency

Operation ADCS2:ADCS0 PIC18F1220/1320 Feature2(4)

2 TOSC 000 1.25 MHz 666 kHz

4 TOSC 100 2.50 MHz 1.33 MHz

8 TOSC 001 5.00 MHz 2.66 MHz

16 TOSC 101 10 .0 MHz 5.33 MHz

32 TOSC 010 20.0 MHz 10.65 MHz

64 TOSC 110 40.0 MHz 21.33 MHz

RC(3) x11 1.00 MHz(1) 1.00 MHz(2)

Note 1: The RC source has a typical TAD time of 4 μs.

2: The R C source has a ty pical TAD time of 6 μs.

3: For device frequencies above 1 MHz, the device must be in Sleep for the entire conversion or the A/D

accuracy may be out of spec ificati on.

4: Low-power devices only.

PIC18F1220/1320

17.5 Operation in Low-Power Modes

The sele ction of the au tom atic acquis it ion time and th e

A/D conversion clock is determined, in part, by the low-

power mode clock source and frequency while in a

low-power mode.

If the A/D is expected to operate while the device is

in a low-power mode, the ACQT2:ACQT0 and

ADCS2:ADCS0 bits in ADCON2 should be updated in

accordance with the low-power mode clock that will be

used. After the low-power mode is entered (either of

the Run mo des), an A/D ac quisi tion or con versio n may

be started. Once an acquisition or conversion is

start ed, the device should continue to be clo cked by the

same low-power mode clock source until the conver-

sion has been complete d. If desired , the devi ce may be

placed into the corresponding low-power (ANY)_IDLE

mode during the conversion.

If the low-power mode clock frequency is less than

1 M Hz, the A/D RC clock source should be selected.

Operation in the Low-Power Sleep mode requires the

A/D RC clock to be selected. If bits, ACQT2:ACQT0, are

set t o ‘000’ and a conversion is started, the conversion

will be delayed one instruction cycle to allow execution

of the SLEEP instruction and entry to Low-Power Sleep

mode. The IDLEN and SCS bits in the OSCCON register

must have already been cleared prior to starting the

conversion.

17.6 Configuring Analog Port Pins

The ADCON1, TRISA and TRISB registers all configure

the A/D port pins. The port pins needed as analog in puts

must have their corresponding TRIS bits set (input). If

the TRIS bit is cleared (output), the digital output level

(VOH or V OL) will be converted.

The A/D operation is independent of the state of the

CHS2:CHS0 bits and the TRIS bits.

Note 1: When reading the Port register, all pins

configured as analog input channels will

read as cleared (a low level). Pins con-

figured as digital inputs will convert an

analog input. Analog levels on a digitally

configured input will be accurately

converted.

2: Analog levels on any pin defined as a

digital input may cause the digital input

buffer to consume current out of the

device’s specification limits.

PIC18F1220/1320

17.7 A/D Conversions

Figure 17-3 shows the operation of the A/D converter

after the GO bit has been set and the ACQT2:ACQT0

bits are cleared. A conversion is started aft er the follow-

ing instruction to allow entry into Low-Power Sleep

mode before the conversion begins.

Figure 17-4 shows the operation of the A/D converter

after the GO bit has been set and the ACQT2:ACQT0

bits are set to ‘010’ and selecting a 4 TAD acquisition

time before the conversion starts.

Clearing the GO/DONE bit during a conversion will

abort the current conversion. The A/D Result register

pair will NOT be updated with the partially completed

A/D conversion sample. This means the

ADRESH:ADRESL registers will continue to contain

the value of the last completed conversion (or the last

value written to the ADRESH:ADRESL registers).

After the A/D conversion is completed or aborted, a

AD wait is required before the next acquisition can

be started. After this wait, acquisition on the selected

channel is automatically started.

FIGURE 17-3: A/D CONVERSION TAD CYCLES (ACQT<2:0> = 000, TACQ = 0)

FIGURE 17-4: A/D CONVERSION TAD CYCLES (ACQT<2:0> = 010, TACQ = 4 TAD)

Note: The GO/DONE bit should NOT be set in

the sam e inst ructio n that tu rns on the A/D.

TAD1TAD2TAD3 TAD4TAD5 TAD6TAD7TAD8 TAD11

Set GO bit

Holding capacitor is disconnected from analog input (typically 100 ns)

TAD9TAD10TCY – TAD

Next Q4: ADRESH/ADRESL is loaded, GO bit is cleared,

ADIF bit is set, holding capacitor is connected to analog input.

Conversion S tarts

b9 b6 b5 b4 b3 b2 b1

b8 b7

123 4 5 67811

Set GO bit

(Hol ding capacitor is disconnected)

910

Next Q4: ADRESH:ADRESL is loaded, GO bit is cleared,

ADIF bit is set, holding capacitor is reconnected to analog input.

Conversion Starts

1234

(Holding capacitor continues

acquiring input)

TACQT Cycles TAD Cycles

Automatic

Acquisition

Time

b0b9 b6 b5 b4 b3 b2 b1

b8 b7

PIC18F1220/1320

17.8 Use of the CCP1 Trigger

An A/D convers ion can be st arted by the “special eve nt

trigger” of the CCP1 module. This requires that the

CCP1M3:CCP1M0 bits (CCP1CON<3:0>) be pro-

grammed as ‘1011’ and tha t the A/D modu le is enabled

(ADON bit is set). When the trigger occurs, the

GO/DONE bit will be set, starting the A/D acquisition

and conv ersio n and the Time r1 (or T i mer3) c ounter w ill

be reset to zero. Timer1 (or Timer3) is reset to auto-

matically repeat the A/D acquisition period with minimal

software overhead (moving ADRESH/ADRESL to the

desired location). The appropriate analog input

channel must b e selecte d and the mi nimum ac quisitio n

period is either timed by the user, or an appropriate

TACQ time selected before the “special event trigger”

sets the GO/DONE bit (starts a conversion).

If the A/D module is not enabled (A DON is c leared), the

“special event trigger” will be ignored by the A/D

module, but will still reset the Timer1 (or Timer3)

counter.

TABLE 17-2: SUMMARY OF A/D REGISTERS

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Val ue on

POR, BOR

Value on

all other

Resets

INTCON GIE/

GIEH PEIE/

GIEL TMR0IE INT0IE RBIE TMR0IF INT0IF RBIF 0000 0000 0000 0000

PIR1 —ADIFRCIF TXIF — CCP1IF TMR2IF TMR1IF -000 -000 -000 -000

PIE1 —ADIERCIE TXIE — CCP1IE TMR2IE TMR1IE -000 -000 -000 -000

IPR1 —ADIPRCIP TXIP — CCP1IP TMR2IP TMR1IP -111 -111 -111 -111

PIR2 OSCFIF — — EEIF —LVDIF TMR3IF — 0--0 -00- 0--0 -00-

PIE2 OSCFIE — — EEIE —LVDIE TMR3IE — 0--0 -00- 0--0 -00-

IPR2 OSCFIP — — EEIP —LVDIP TMR3IP — 1--1 -11- 1--1 -11-

ADRESH A/D Result Register High Byte xxxx xxxx uuuu uuuu

ADRESL A/D Result Register Low Byte xxxx xxxx uuuu uuuu

ADCON0 VCFG1 VCFG0 — CHS2 CHS1 CHS0 GO/DONE ADON 00-0 0000 00-0 0000

ADCON1 — PCFG6 PCFG5 PCFG4 PCFG3 PCFG2 PCFG1 PCFG0 -000 0000 -000 0000

ADCON2 ADFM — ACQT2 ACQT1 ACQT0 ADCS2 ADCS1 ADCS0 0-00 0000 0-00 0000

PORTA RA7(3) RA6(2) RA5(1) RA4 RA3 RA2 RA1 RA0 qq0x 0000 uu0u 0000

TRISA TRISA7(3) TRISA6(2) — PORTA Data Direction Register qq-1 1111 11-1 1111

PORTB Read PORTB pins, Write LATB Latch xxxx xxxx uuuu uuuu

TRISB PORTB Data Direction Register 1111 1111 1111 1111

LATB PORTB Output Data Latch xxxx xxxx uuuu uuuu

Legend: x = unknown, u = unchanged, q = depends on CONFIG1H<3:0>, – = unimplemented, read as ‘0’.

Shaded cells are not used for A/D conversion.

Note 1: RA5 port bit is available only as an input pin when the MCLRE bit in the configuration register is ‘0’.

2: RA6 and TRISA6 are available only when the primary oscillator mode selection offers RA6 as a port pin; otherwise, RA6

always reads ‘0’, TRISA6 always reads ‘1’ and writes to both are ignored (see CONFIG1H<3:0>).

3: RA7 and TRISA7 are available only when the internal RC oscillator is configured as the primary oscillator in

CONFIG1H<3:0>; otherwise, RA7 always reads ‘0’, TRISA7 always reads ‘1’ and writes to both are ignored.

PIC18F1220/1320

18.0 LOW-VOLTAGE DETECT

In many applications, the ability to determine if the

device voltage (VDD) is below a specified voltage level

is a desirable feature. A window of operation for the

application can be created, where the application soft-

ware can do “housekeeping tasks”, before the device

voltage exits the valid operating range. This can be

done using the Low-Voltage Detect module.

This module is a software programmable circuitry,

where a device voltage trip point can be specified.

When the v oltage of the device becomes lower th en the

specif ied poin t, an inter rupt flag is set. If the interrupt is

enabled , the program exec ution will bran ch to the inter-

rupt vec tor addre ss and th e softw are c an then respon d

to that interrupt source.

The Low-Voltage Detect circuitry is completely under

software control. This allows the circuitry to be turned

off by the software, which minimizes the current

consum pt ion for the devic e.

Figur e 18-1 sho ws a po ssible a pplication v olt age curve

(typically for batteries). Over time, the device voltage

decreas es. When the device voltage equals volt age V A,

the LVD logic generates an interrupt. This occurs at

time TA. The application software then has the time,

until the device voltage is no longer in valid operating

range, to sh ut down the s ystem. Voltage poi nt VB is the

minimum valid operating voltage specification. This

occur s at time TB. The difference, TB – TA, is the total

time for shutdown.

The block diagram for the LVD module is shown in

Figure 18-2 (following page). A comparator uses an

internally generated reference voltage as the set point.

When the selected tap output of the device voltage

crosses the set point (is lower than), the LVDIF bit is set.

Each node in the resistor divider represents a “trip

point” voltage. The “trip point” voltage is the minimum

supply voltage level at which the device can operate

before the LVD module asserts an interrupt. When the

supply voltage is equal to the trip point, the voltage

tapped off of the resistor array is equal to the 1.2V

internal reference voltage generated by the voltage

reference module. The comparator then generates an

interrupt signal setting the LVDIF bit. This voltage is

software programmable to any one of 16 values (see

Figure 18-2). The trip point is selected by

programming the LVDL3:LVDL0 bits (LVDCON<3:0>).

FIGURE 18-1: TYP ICAL LOW-VOLTAGE DETECT APPLICATION

Time

Voltage

TATB

Legend: VA = LVD trip point

VB = Minimum valid device

operating voltage

PIC18F1220/1320

FIGURE 18-2: LOW-VOLT AGE DETECT (LVD) BLOCK DIAGRAM

The LVD module has an additional feature that allows

the user to supply the trip voltage to the module from

an external source. This mode is enabled when bits,

LVDL3:LVDL0, are set to ‘1111’. In this st ate , the com-

parator input is multiplexed from the external input pin,

LVDIN (Figure 18-3). This gives users flexibility,

because it allows them to configure the Low-Voltage

Detect interrupt to occur at any voltage in the valid

operating range.

FIGURE 18-3: LOW-VOLTAGE DETECT (LVD) WITH EXTERNAL INPUT BLOCK DIAGRAM

LVDIF

VDD

16- to- 1 MUX

LVDEN

LVD Control

Internally Generated

Reference Voltage

LVDIN

1.2V

LVD

LVD Control

16-to-1 MUX

BGAP

BODEN

LVDEN

VxEN

LVDIN

VDD VDD

Externally Generated

Trip Point

PIC18F1220/1320

18.1 Control Register

The Low-Voltage Detect Control register controls the

operation of the Low-Voltage Detect circuitry.

U-0 U-0 R-0 R/W-0 R/W-0 R/W-1 R/W-0 R/W-1

—— IRVST LVDEN LVDL3 LVDL2 LVDL1 LVDL0

bit 7 bit 0

bit 7-6 Unimplemented: Read as ‘0’

bit 5 IRVST: Intern al Reference Voltage Stable Fl ag bit

1 = Indicates that the Low-Voltage Detect logic will generate the interrupt flag at the specified

voltage range

0 = Indicates that the Low-Voltage Detect logic will not generate the interrupt flag at the

specified voltage range and the LVD interrupt should not be enabled

bit 4 LVDEN: Low-Voltage Detect Power Enable bit

1 = Enables LVD, powers up LVD circuit

0 = Disables LVD, powers down LVD circuit

bit 3-0 LVDL3:LVDL0: Low-Voltage Detection Limit bits

1111 = External analog input is used (input comes from the LVDIN pin)

1110 = 4.04V-5.15V

1101 = 3.76V-4.79V

1100 = 3.58V-4.56V

1011 = 3.41V-4.34V

1010 = 3.23V-4.11V

1001 = 3.14V-4.00V

1000 = 2.96V-3.77V

0111 = 2.70V-3.43V

0110 = 2.53V-3.21V

0101 = 2.43V-3.10V

0100 = 2.25V-2.86V

0011 = 2.16V-2.75V

0010 = 1.99V-2.53V

0001 = Reserved

0000 = Reserved

Note: LVDL3:LVDL0 modes, which result in a trip point below the valid operating voltage

of the device, are not tested.

Legend:

R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’

-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown

PIC18F1220/1320

18.2 Operation

Depen ding on the power s our ce for th e devi ce volt ag e,

the voltage normally decreases relatively slowly. This

means that the LVD module does not need to be

constantly operating. To decrease the current require-

ments, the LVD circuitry only needs to be enabled for

short periods, where the voltage is checked. After

doing the check, the LVD module may be disabled.

Each tim e that the LVD mo dule i s enab led, th e circ uitry

requires some time to stabilize. After the circuitry has

stabilized, all status flags may be cleared. The module

will then indicate the proper state of the system.

The following steps are needed to set up the LVD

module:

1. Write the value to the LVDL3:LVDL0 bits

(LVDCON register), which selects the desired

LVD trip point.

2. Ensure that LVD interrupts are disabled (the

LVDIE bit is cleared or the GIE bit is cleared).

3. Enable the LVD module (set the LVDEN bit in

the LVDCON register).

4. Wait for the LVD module to stabilize (the IRVST

bit to become set).

5. Clear the LVD interrupt flag, which may have

falsely become set, until the LVD module has

stabilized (clear the LVDIF bit).

6. Enable the LVD interru pt (set the LVDIE and th e

GIE bits).

Figure 18-4 shows typical waveforms that the LVD

module may be used to detect.

FIGURE 18-4: LOW-VOLTAGE DETECT WAVEFORMS

VLVD

VDD

LVDIF

VLVD

VDD

Enable LVD

Internally Generated TIVRST

LV DIF may not be set.

Enable LVD

LVDIF

LVDIF cleared in software

LV DIF cleared in software,

CASE 1:

CASE 2:

LV DIF remains set since LVD condition still exists

Reference Stable

Internally Generated

Reference Stable TIVRST

PIC18F1220/1320

18.2.1 REFERENCE VOLTAGE SET POINT

The internal reference voltage of the LVD module may

be used by other internal circuitry (the programmable

Brown-out Reset). If these circuits are disabled (lower

current consumption), the reference voltage circuit

requires a time to become stable before a low-voltage

condition can be reliably detected. This time is invariant

of system clock speed. This start-up time is specified in

electrical specification parameter 36. The low-voltage

interrupt flag will not be enabled until a stable reference

voltage is reached. Refer to the waveform in Figure 18-4.

18.2.2 CURRENT CONSUMPTION

When the module is enabled, the LVD comparator and

voltage divider are enabled and will consume st atic cur-

rent. The voltage divider can be tapped from multiple

places in the resistor array. Total current consumption,

when enabled, is specified in electrical specification

parameter D022B.

18.3 Operation During Sleep

When enabled, the LVD circuitry continues to operate

during Sleep. If the device voltage crosses the trip

point, the L VDIF bit will be set and the devi ce will wake-

up from Sleep. Device execution will continue from the

interr upt vecto r address if interru pts h ave been globall y

enabled.

18.4 Effects of a Reset

A device Reset forces all registers to their Reset state.

This forces the LVD module to be turned off.

PIC18F1220/1320

NOTES:

PIC18F1220/1320

19.0 SPECIAL FEATURES OF

THE CPU

PIC18F1220/1320 devices include several features

intended to maximize system reliability, minimize cost

through elimination of external components and offer

code protection. These are:

• Oscillator Selection

• Resets:

- Power-on Reset (P OR)

- Power-up Timer (PWRT)

- Oscillator Start-up Timer (OST)

- Brown-out Reset (BOR)

• Interrupts

• Watchdog Timer (WDT)

• Fail-Safe Clock Monitor

• Two-Speed Start-up

• Code Protection

• ID Locations

• In-Circuit Serial Programming

Several oscillator options are available to allow the part

to fit the application. The RC oscillator option saves

system cost, while the LP crystal option saves power.

These are discussed in detail in Section 2.0 “Oscillator

Configurations”.

A complete discussion of device Resets and interrupts

is avail able in previous sections of this data sheet.

In addition to their Power-up and Oscillator Start-up

T imers p rovided for Res ets, PIC18F 1220/1320 de vices

have a Watchdog Timer, which is either permanently

enabled via the configuration bits, or software

controlled (if configured as disabled).

The inclu sio n of an in ternal RC oscill ator also provides

the additional benefits of a Fail-Safe Clock Monitor

(FSCM) and Two-Speed Start-up. FSCM provides for

background monitoring of the peripheral clock and

automatic switchover in the event of its failure. Two-

Speed Start-up enables code to be executed almost

immedi ately on s tart-up, while th e primary clock so urce

completes its start-up delays.

All of these features are enabled and configured by

setting the appropriate configuration register bits.

19.1 Configuration Bits

The configuration bits can be programmed (read as

‘0’), or left unprogrammed (read as ‘1’), to select vari-

ous device configurations. These bits are mapped

starting at program memory location 300000h.

The user will note that address 300000h is beyond the

user program memory space. In fact, it belongs to the

configuration memory space (300000h-3FFFFFh),

which can only be accessed using table reads and

table writes.

Programming the configuration registers is done in a

manner s imilar to p rogrammin g the Flas h memo ry. The

EECON1 regist er WR bit sta rts a se lf-tim ed w rite to the

configuration register. In normal operation mode, a

TBLWT instruction, with the TBLPTR pointing to the

configu ration regist er , sets up the addre ss and the data

for the configuration register write. Setting the WR bit

start s a long write to the configuration register . The con-

figuratio n regis ters are writt en a by te at a t ime. To write

or erase a configuration cell, a TBLWT instruction can

write a ‘1’ or a ‘0’ into the cell. For additional details on

Flash programming, refer to Section 6.5 “Writing to

Flash Program Memory”.

TABLE 19-1: CONFIGURATION BITS AND DEVICE IDS

File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 B it 1 Bit 0 Default/

Unprogrammed

Value

300001h CONFIG1H IESO FSCM —— FOSC3 FOSC2 FOSC1 FOSC0 11-- 1111

300002h CONFIG2L — — — — BORV1 BORV0 BOR PWRTEN ---- 1111

300003h CONFIG2H — — — WDTPS3 WDTPS2 WDTPS1 WDTPS0 WDT ---1 1111

300005h CONFIG3H MCLRE — — — — — — — 1--- ----

300006h CONFIG4L DEBUG — — — —LVP—STVR1--- -1-1

300008h CONFIG5L — — — — — —CP1CP0---- --11

300009h CONFIG5H CPD CPB — — — — — — 11-- ----

30000Ah CONFIG6L — — — — — — WRT1 WRT0 ---- --11

30000Bh CONFIG6H WRTD WRTB WRTC — — — — — 111- ----

30000Ch CONFIG7L — — — — — — EBTR1 EBTR0 ---- --11

30000Dh CONFIG7H —EBTRB— — — — — — -1-- ----

3FFFFEh DEVID1(1) DEV2 DEV1 DEV0 REV4 REV3 REV2 REV1 REV0 xxxx xxxx(1)

3FFFFFh DEVID2(1) DEV10 DEV9 DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 0000 0111

Legend: x = unknown, u = unchanged, – = unimplemented. Shaded cells are unimplemented, read as ‘0’.

Note 1: See Register 19-14 for DEVID1 values. DEVID registers are read-only and cannot be programmed by the user.

PIC18F1220/1320

R/P-1 R/P-1 U-0 U-0 R/P-1 R/P-1 R/P-1 R/P-1

IESO FSCM —— FOSC3 FOSC2 FOSC1 FOSC0

bit 7 bit 0

bit 7 IESO: Internal External Switchover bit

1 = Internal External Switchover mode enabled

0 = Internal External Switchover mode disabled

bit 6 FSCM: Fail-Safe Clock Moni tor Enab le bit

1 = Fail- Safe Clock Monitor enabled

0 = Fail-Safe Clock Monitor disabled

bit 5-4 Unimplemented: Read as ‘0’

bit 3-0 FOSC<3:0>: Oscillat or Selection bits

11xx = External RC oscillator, CLKO function on RA6

1001 = Internal RC oscillator, CLKO function on RA6 and port function on RA7

1000 = Internal RC oscillator, port function on RA6 and port function on RA7

0111 = External RC oscillator, port function on RA6

0110 = HS oscillator, PLL enabled (clock frequency = 4 x FOSC1)

0101 = EC oscillator, port function on RA6

0100 = EC oscillator, CLKO function on RA6

0010 = HS oscillator

0001 = XT oscillator

0000 = LP oscillator

Legend:

R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’

-n = Value when device is unprogrammed u = Unchanged from programmed state

PIC18F1220/1320

U-0 U-0 U-0 U-0 R/P-1 R/P-1 R/P-1 R/P-1

— — — — BORV1 BORV0 BOR PWRTEN

bit 7 bit 0

bit 7-4 Unimplemented: Read as ‘0’

bit 3-2 BORV1:BORV0: Brown-out Reset Voltage bits

11 = Reserved

10 = VBOR se t to 2.7V

01 = VBOR se t to 4.2V

00 = VBOR se t to 4.5V

bit 1 BOR: Brown-out R eset Enable bit(1)

1 = Brown-out Reset enabled

0 = Brown-out Reset disabled

bit 0 PWRTEN: Power-up Timer Enable bit(1)

1 = PWRT disabled

0 = PWRT enabled

Note 1: The Power-up T im er is decoupled from Brown-out Rese t, allowing thes e features to

be independently controlled.

Legend:

R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’

-n = Value when device is unprogrammed u = Unchanged from programmed state

PIC18F1220/1320

U-0 U-0 U-0 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1

— — — WDTPS3 WDTPS2 WDTPS1 WDTPS0 WDTEN

bit 7 bit 0

bit 7-5 Unimplemented: Read as ‘0’

bit 4-1 WDTPS<3:0>: Watchdog Timer Postscale Select bits

1111 = 1:32,768

1110 = 1:16,384

1101 = 1:8,192

1100 = 1:4,096

1011 = 1:2,048

1010 = 1:1,024

1001 = 1:512

1000 = 1:256

0111 = 1:128

0110 = 1:64

0101 = 1:32

0100 = 1:16

0011 = 1:8

0010 = 1:4

0001 = 1:2

0000 = 1:1

bit 0 WDT: Watchdog Timer Enable bit

1 = WDT enabled

0 = WDT disabled (control is placed on the SWDTEN bit)

Legend:

R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’

-n = Value when device is unprogrammed u = Unchanged from programmed state

PIC18F1220/1320

R/P-1 U-0 U-0 U-0 U-0 U-0 U-0 U-0

MCLRE — — — — — — —

bit 7 bit 0

bit 7 MCLRE: MCLR Pin Enable bit

1 =MCLR pin enabled, RA5 input pin disabled

0 = RA5 input pin enabled, MCLR disabled

bit 6-0 Unimplemented: Read as ‘0’

Legend:

R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’

-n = Value when device is unprogrammed u = Unchanged from programmed state

R/P-1 U-0 U-0 U-0 U-0 R/P-1 U-0 R/P-1

DEBUG — — — —LVP—STVR

bit 7 bit 0

bit 7 DEBUG: Background Debugger Enable bit (see note)

1 = Background debugger disabled, RB6 and RB7 configured as general purpose I/O pins

0 = Background debugger enabled, RB6 and RB7 are dedicated to In-Circuit Debug

bit 6-3 Unimplemented: Read as ‘0’

bit 2 LVP: Low-Voltage ICSP Enable bit

1 = Low-Voltage ICSP enabled

0 = Low-Voltage ICSP disabled

bit 1 Unimplemented: Read as ‘0’

bit 0 STVR: Stack Full /U nd erfl ow Reset Enab le bit

1 = Stack full/underflow will cause Reset

0 = Stack full/underflow will not cause Reset

Legend:

R = Readable bit C = Clearable bit U = Unimplemented bit, read as ‘0’

-n = Value when device is unprogrammed u = Unchanged from programmed state

Note: The Timer1 oscillator shares the T1OSI and T1OSO pins with the PGD and PGC

pins used for programming and debugging.

When using the Timer1 oscillator, In-Circuit Serial Programming (ICSP) may not

function correctly (hi gh voltag e or low v oltage), o r the In-Circuit Debugger (ICD) may

not communicate with the controller. As a result of using either ICSP or ICD, the

Timer1 crystal may be damaged.

If ICSP or ICD ope rati ons a r e requ ire d, the c rys tal shou ld be d is con ne cte d f r om th e

circuit (d isco nnect eit her lea d) or in st alled after pr ogra mming. T he oscilla tor loa din g

capacitors may remain in-circuit during ICSP or ICD operation.

PIC18F1220/1320

U-0 U-0 U-0 U-0 R/C-1 R/C-1 R/C-1 R/C-1

— — — — — —CP1CP0

bit 7 bit 0

bit 7-2 Unimplemented: Read as ‘0’

bit 1 CP1: Code Protection bit (PIC18F1320)

1 = Block 1 (001000-001FFFh) not code-protected

0 = Block 1 (001000-001FFFh) code-protected

bit 0 CP0: Code Protection bit (PIC18F1320)

1 = Block 0 (00200-000FFFh) not code-protected

0 = Block 0 (00200-000FFFh) code-protected

bit 1 CP1: Code Protection bit (PIC18F1220)

1 = Block 1 (000800-000FFFh) not code-protected

0 = Block 1 (000800-000FFFh) code-protected

bit 0 CP0: Code Protection bit (PIC18F1220)

1 = Block 0 (000200-0007FFh) not code-protected

0 = Block 0 (000200-0007FFh) code-protected

Legend:

R = Readable bit C = Clearable bit U = Unimplemented bit, read as ‘0’

-n = Value when device is unprogrammed u = Unchanged from programmed state

R/C-1 R/C-1 U-0 U-0 U-0 U-0 U-0 U-0

CPD CPB — — — — — —

bit 7 bit 0

bit 7 CPD: Data EEPROM Code Protection bit

1 = Data EEPROM not code-protected

0 = Data EEPROM code-protected

bit 6 CPB: Boot Block Code Protection bit

1 = Boot Block (000000-0001FFh) not code-protected

0 = Boot Block (000000-0001FFh) code-protected

bit 5-0 Unimplemented: Read as ‘0’

Legend:

R = Readable bit C = Clearable bit U = Unimplemented bit, read as ‘0’

-n = Value when device is unprogrammed u = Unchanged from programmed state

PIC18F1220/1320

U-0 U-0 U-0 U-0 U-0 U-0 R/P-1 R/P-1

— — — — — — WRT1 WRT0

bit 7 bit 0

bit 7-2 Unimplemented: Read as ‘0’

bit 1 WRT1: Write Protection bit (PIC18F1320)

1 = Block 1 (001000-001FFFh) not write-protected

0 = Block 1 (001000-001FFFh) write-protected

bit 0 WRT0: Write Protection bit (PIC18F1320)

1 = Block 0 (00200-000FFFh) not write-protected

0 = Block 0 (00200-000FFFh) write-protected

bit 1 WRT1: Write Protection bit (PIC18F1220)

1 = Block 1 (000800-000FFFh) not write-protected

0 = Block 1 (000800-000FFFh) write-protected

bit 0 WRT0: Write Protection bit (PIC18F1220)

1 = Block 0 (000200-0007FFh) not write-protected

0 = Block 0 (000200-0007FFh) write-protected

Legend:

R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’

-n = Value when device is unprogrammed u = Unchanged from programmed state

R/P-1 R/P-1 R-1 U-0 U-0 U-0 U-0 U-0

WRTD WRTB WRTC — — — — —

bit 7 bit 0

bit 7 WRTD: Data EEPROM Write Protection bit

1 = Data EEPROM not write-protected

0 = Data EEPROM write-protected

bit 6 WRTB: Boot Block Write Protection bit

1 = Boot Block (000000-0001FFh) not write-protected

0 = Boot Block (000000-0001FFh) write-protected

bit 5 WRTC: Configuration Register Write Protection bit

1 = Configuration registers (300000-3000FFh) not write-protected

0 = Configuration registers (300000-3000FFh) write-protected

Note: This bit is read-only in normal execution mode; it can be written only in Program mode.

bit 4-0 Unimplemented: Read as ‘0’

Legend:

R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’

-n = Value when device is unprogrammed u = Unchanged from programmed state

PIC18F1220/1320

U-0 U-0 U-0 U-0 U-0 U-0 R/P-1 R/P-1

— — — — — — EBTR1 EBTR0

bit 7 bit 0

bit 7-2 Unimplemented: Read as ‘0’

bit 1 EBTR1: Table Read Protection bit (PIC18F1320)

1 = Block 1 (001000-001FFFh) not protected from table reads executed in other blocks

0 = Block 1 (001000-001FFFh) protected from table reads executed in other blocks

bit 0 EBTR0: Table Read Protection bit (PIC18F1320)

1 = Block 0 (00200-000FFFh) not protected from table reads executed in other blocks

0 = Block 0 (00200-000FFFh) protected from table reads executed in other blocks

bit 1 EBTR1: Table Read Protection bit (PIC18F1220)

1 = Block 1 (000800-000FFFh) not protected from table reads executed in other blocks

0 = Block 1 (000800-000FFFh) protected from table reads executed in other blocks

bit 0 EBTR0: Table Read Protection bit (PIC18F1220)

1 = Block 0 (000200-0007FFh) not protected from table reads executed in other blocks

0 = Block 0 (000200-0007FFh) protected from table reads executed in other blocks

Legend:

R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’

-n = Value when device is unprogrammed u = Unchanged from programmed state

U-0 R/P-1 U-0 U-0 U-0 U-0 U-0 U-0

— EBTRB — — — — — —

bit 7 bit 0

bit 7 Unimplemented: Read as ‘0’

bit 6 EBTRB: Boot Bl ock Table Read Protect ion bit

1 = Boot Block (000000-0001FFh) not protected from table reads executed in other blocks

0 = Boot Block (000000-0001FFh) protected from table reads executed in other blocks

bit 5-0 Unimplemented: Read as ‘0’

Legend:

R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’

-n = Value when device is unprogrammed u = Unchanged from programmed state

PIC18F1220/1320

RRRRRRRR

DEV2 DEV1 DEV0 REV4 REV3 REV2 REV1 REV0

bit 7 bit 0

bit 7-5 DEV2:DEV0: Device ID bits

111 = PIC18F1220

110 = PIC18F1320

bit 4-0 REV4:REV0: Revision ID bits

These bits are used to indicate the device revision.

Legend:

R = Read-only bit P = Programmable bit U = Unimplemented bit, read as ‘0’

-n = Value when device is unprogrammed u = Unchanged from programmed state

RRRRRRRR

DEV10 DEV9 DEV8 DEV7 DEV6 DEV5 DEV4 DEV3

bit 7 bit 0

bit 7-0 DEV10:DEV3: Device ID bits

These bits are used with the DEV2:DEV0 bits in the Device ID Register 1 to identify the

part number.

0000 0111 = PIC18F1220/1320 devices

Note: These values for DEV10:DEV3 may be shared with other devices. The specific

device is always identified by using the entire DEV10:DEV0 bit sequence.

Legend:

R = Read-only bit P = Programmable bit U = Unimplemented bit, read as ‘0’

-n = Value when device is unprogrammed u = Unchanged from programmed state

PIC18F1220/1320

19.2 Watchdog Timer (WDT)

For PIC18F1220/1320 devices, the WDT is driven by the

INTRC source. When the WDT is enabled, the clock

source is also enabled. The nominal WDT period is 4 ms

and has the same stability as the INTRC osc illator.

The 4 ms period of the WDT is multiplied by a 16-bit

postscal er . Any output of the WDT postscal er is selected

by a multiplexer, controlled by bits in Configuration

131.072 seconds (2.18 minutes). The WDT and

postscaler are cleared when any of the following events

occur: execute a SLEEP or CLRWDT instruction, the IRCF

bits ( OSCCON<6:4>) are chang ed or a clock failure has

occurred.

Adjustm ents to the internal o scillator c lock pe riod using

the OSCTUNE register also affect the period of the

WDT by the same factor. For example, if the INTRC

period is increased by 3%, then the WDT period is

increased by 3%.

19.2.1 CONTROL REGIST ER

Regi ste r 19-14 sh ows the WDT CON re gi s te r. Th is is a

readable and wri table re gister, which cont ains a control

bit that allows software to override the WDT enable

configuration bit, only if the configuration bit has

disabled the WDT.

FIGURE 19-1: WDT BLOCK DIAGRAM

Note 1: The CLRWDT and SLEEP instructions

clear the WDT and postscaler counts

when executed.

2: Changing the setting of the IRCF bits

(OSCCON<6:4>) clears the WDT and

postscaler counts.

3: When a CLRWDT instruction is executed

the postscaler count will be cleared.

U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0

— — — — — — —SWDTEN

bit 7 bit 0

bit 7-1 Unimplemented: Read as ‘0’

bit 0 SWDTEN: Software Controlled Watchdog Timer Enable bit

1 = Watchdog Timer is on

0 = Watchdog Timer is off

Note: This bit has no effec t if the configurat ion bit, WDT EN (CONFIG2H< 0>), is enable d.

Legend:

R = Readable bit W = Writable bit -n = Value at POR

U = Unimplemented bit, read as ‘0’

INTRC Oscillator

WDT

Wake-up

Reset

WDT

WDT C o unter

(31 kHz)

Program ma ble P ostscaler

1:1 to 1:32,768

Enable WDT

WDTPS<3:0>

SWDTEN

WDTEN

CLRWDT

from Sleep

Reset

All Device

Sleep

INTRC Control

Resets

÷125

PIC18F1220/1320

TABLE 19-2: SUMMARY OF WATCHDOG TIMER REGISTERS

19.3 Two-Speed Start-up

The Two-Speed Start-up feature helps to minimize the

latency period from oscillator st art-up to code execution

by allowing the microcontroller to use the INTRC oscil -

lator as a clo ck sourc e until the prim ary c loc k so urc e i s

available. It is enabled by setting the IESO bit in

Conf iguration Register 1H (CONFIG1H<7>).

T wo-Speed Start-up is available only if the primary oscil-

lator mode is LP, XT, HS or HSPLL (crystal-based

modes). Oth er sour ces do not r equir e an OST start -up

delay; fo r these, Two-Speed Start-up is disabled.

When ena bled, Resets and wake- ups from Sleep mode

cause the device to configure itself to run from the

internal oscillator block as the clock source, following

the time-out of the Power-up Timer after a Power-on

Reset is enabled. This allows almost immediate code

execution while the primary oscillator starts and the

OST is running. Once the OST times out, the device

automatically switch es to PRI_RUN mode.

Because the OSCCON register is cleared on Reset

events , the IN T O SC (or pos tscaler) cloc k s ource is not

initially available after a Reset event; the INTRC clock

is used directly at its base frequency. To use a higher

clock speed on wake-up, the INTOSC or postscaler

clock sour ces can be sele cted to provide a higher cloc k

speed by set ti ng bi ts, IFR C2: IFR C0, im medi at ely aft er

Reset. For wake-ups from Sleep, the INTOSC or

postscaler clock sources can be selected by setting

IFRC2:IFRC0 prior to entering Sleep mode.

In all other power managed modes, T wo-Speed S tart-up

is not used. The device will be clocked by the currently

selected clock source until the primary clock source

becomes available. The setting of the IESO bit is

ignored.

19.3.1 SPECIAL CONSIDERATIONS FOR

USING TWO-SPEED START-UP

While using the INTRC oscillator in Two-Speed Start-

up, the device still obeys the normal command

sequences for entering power managed modes, includ-

ing serial SLEEP instructions (refer to Section 3.1.3

“Multiple Sleep Commands”). In pr actice, this me ans

that user co de can chang e the SCS1:SCS0 bit settings

and iss ue SLEEP commands before the OST times out.

This w ould allo w an a pplic ation to briefly w ake-u p, per-

form routine “housekeeping” tasks and return to Sleep

before the device starts to operate from the primary

oscillator.

User code can a lso c heck if t he primar y clo ck s our ce i s

currently providing th e system cloc king by check ing the

status of the OSTS bit (OSCCON<3>). If the bit is set,

the primary oscillator is providing the system clock.

Otherwise, the internal oscillator block is providing the

clock during wake-up from Reset or Sleep mode.

FIGURE 19-2: TIMING TRANSITION FOR TWO-SPEED START-UP (INTOSC TO HSPLL)

Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

CONFIG2H — — — WDTPS3 WDTPS2 WDTPS2 WDTPS0 WDTEN

RCON IPEN — — RI TO PD POR BOR

WDTCON — — — — — — —SWDTEN

Legend: Shaded cells are not used by the Watchdog Timer.

Q1 Q3 Q4

OSC1

Peripheral

Program PC PC + 2

INTOSC

PLL Clock

PC + 6

Output

Q3 Q4 Q1

CPU Clock

PC + 4

Clock

Counter

Q2 Q2 Q3 Q4

Note 1: TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale.

Wake from Interrupt Event

TPLL(1)

12345678

Clock Transition

OSTS bit Set

Multiplexer

TOST(1)

PIC18F1220/1320

19.4 Fail-Safe Clock Monitor

The Fail-Safe Clock Monitor (FSCM) allows the micro-

controller to continue operation, in the event of an

external oscillator failure, by automatically switching

the system clock to the internal oscillator block. The

FSCM function is enabled by setting the Fail-Safe

Clock Monitor Enable bit, FSCM (CONFIG1H<6>).

When FSCM is enabled, the INTRC oscillator runs at

all times to monitor clocks to peripherals and provide

an ins tant ba ckup c lock in the e vent of a cloc k fail ure.

Clock monitoring (shown in Figure 19-3) is accom-

plished by creating a sample clock signal, which is the

INTRC output divided by 64. This allows ample time

between FSCM sample clocks for a peripheral clock

edge to occur. The peripheral system clock and the

sample clock are presented as inputs to the Clock

Monitor latch (CM). The CM is set on the falli ng edge of

the sys tem clock source, but cleare d on the risi ng edge

of the sample clock.

FIGURE 19-3: FSCM BLOCK DIAGRAM

Clock failure is tested for on the falling edge of the sam-

ple clock. If a sample clock falling edge occurs while

CM is still set, a clock failure has been detected

(Figure 19-4). This causes the following:

• the FSCM genera tes an oscillator fail int erru pt by

setting bit, OSCFIF (PIR2<7>);

• the system clock source is sw itched to t he intern al

oscill ato r blo ck (O SCC ON i s not up dated to show

the current clock source – this is the Fail-Safe

condition); and

•the WDT is reset.

Since the postscaler frequency from the internal oscil-

lator block may not be sufficiently stable, it may be

desirable to select another clock configuration and

enter an alternate power managed mode (see

Section 19.3.1 “Special Considerations for Using

Two-Speed Start-up” and Section 3.1.3 “Multiple

Sleep Commands” for more details). This can be

done to attempt a partial recovery, or execute a

controlled shutdown.

To use a higher clock speed on wake-up, the INTOSC

or postscaler clock sources can be selected to provide

a higher clock speed by setting bits, IFRC2:IFRC0,

immediate ly a fter Res et. Fo r wake-u p s fro m Sle ep, th e

INTOSC or postscaler clock sources can be selected

by setting IFRC2:IFRC0 prior to entering Sleep mode.

Adjustments to the internal oscillator block, using the

OSCTUNE register, also affect the period of the FSCM

by the same factor. This can usually be neglected, as

the cloc k freq uen cy be ing monitored is generally m uc h

higher than the sample clock frequency.

The FS CM will dete ct failure s of the p rimary or sec ond-

ary clock sources only. If the internal oscillator block

fails, no failure would be detected, nor would any actio n

be possible.

19.4.1 FSCM AND THE WATCHDOG T IMER

Both the FSCM and the WDT are clocked by the

INTRC oscillator. Since the WDT operates with a

separate divider and counter, disabling the WDT has

no ef fect on the op eration of the INTRC oscill ator when

the FSCM is enabled.

As already noted, the clock source is switched to the

INTOSC clock when a clock failure is detected.

Depending on the frequency selected by the

IRCF2:IRCF0 bits, this may mean a substantial change

in the speed of code execution. If the WDT is enabled

with a small prescale value, a decrease in clock speed

allows a WDT time-out to occur and a subsequent

device Reset. For this reason, Fail-Safe Clock events

also reset the WDT and postscaler, allowing it to start

timing from when execution speed was changed and

decreasing the likelihood of an erroneous time-out.

Peripheral

INTRC ÷ 64

(32 μs) 488 Hz

(2.048 ms)

Clock Monitor

Latc h ( C M)

(edge-triggered)

Clock

Failure

Detected

Source

Clock

PIC18F1220/1320

19.4.2 EXITING FAIL-SAFE OPERATION

The Fail-Sa fe condition is te rminated by eith er a device

Reset, or by entering a power managed mode. On

Reset, the controller starts the primary clock source

specified in Configuration Register 1H (with any

required start-up delays that are required for the

oscillator mode, such as OST or PLL timer). The

INT OSC multiplex er provides the sy stem clock unt il the

primary clock so urce becom es ready (similar to a Two-

Speed Start-up). The clock system source is then

switched to the primary clock (indicated by the OSTS

bit in the OSCCON register becoming set). The Fail-

Safe Clock Monitor then resumes monitoring the

periphe ral clock.

The primary clock source may never become ready

during st art-up. In thi s case, operatio n is clocked by the

INTOSC multiplexer . The OSCCON register will remain

in its Reset state until a power managed mode is

entered.

Entering a power managed mode by loading the

OSCCON register and executing a SLEEP instruction

will clear the Fail-Safe condition. When the Fail-Safe

condition is cleared, the clock monitor will resume

monitoring the peripheral clock.

19.4.3 FSCM INTERRUPTS IN POWER

MANAGED MODES

As previously mentioned, entering a power managed

mode clears the Fail-Safe condition. By entering a

power managed mode, the clock multiplexer selects

the clock source selected by the OSCCON register.

Fail-Safe monitoring of the power managed clock

source resumes in the power managed mode.

If an oscillator failure occurs during power managed

operation, the subsequent events depend on whether

or not the oscillator failure interrupt is enabled. If

enabled (OSCFIF = 1), code execution will be clocked

by the INTOSC multiplexer. An automatic transition

back to the failed clock source will not occur.

If the interrupt is disabled, the device will not exit the

power managed mode o n oscillato r failure. Inste ad, the

device will continue to operate as before, but clocked

by the INTOSC m ul tip lex er. While in Id le mode, su bs e-

quent interrupts will cause the CPU to begin executing

instructions while being clocked by the INTOSC multi-

plexer. The de vi ce will not trans itio n t o a diff e rent cl oc k

source until the Fail-Safe condition is cleared.

FIGURE 19-4: FSCM TIMING DIAGRAM

OSCFIF

CM Output

System

Clock

Output

Sample Clock

Failure

Detected

Oscillator

Failure

Note: The system c lock is normally at a much higher frequency than the sample clock . The relative frequencies in

this example have been chosen for clarity.

(Q)

CM Test CM Test CM Test

PIC18F1220/1320

19.4.4 POR OR WAKE FROM SLEEP

The FS CM is designed to detect osc illator failu re at any

point after the device has exited Power-on Reset

(POR) or Low-Power Sleep mode. When the primary

system clock is EC, RC or INTRC modes, monitoring

can begin immediately following these events.

For oscillator modes involving a crystal or resonator

(HS, HSPLL, LP or XT), the situation is somewhat dif-

ferent. Since the oscillator may require a start-up time

consid erably longer th an the FCSM s ample clock tim e,

a false clock failure may be detected. To prevent this,

the internal oscillator block is automatically configured

as the system clock and functions until the primary

clock is stable (the OST and PLL timers have timed

out). This is identical to Two-Speed Start-up mode.

Once the primary clock is stable, the INTRC returns to

its role as the FSCM source

As not ed in Section 19.3.1 “Special Considerations

for Using Two-Speed Start-up”, it is also possible to

select another clock configuration and enter an alter-

nate power managed mode while waiting for the

primary sy s t em c loc k to become st able. When the new

powere d manag ed mode is selecte d, th e primary cl ock

is disabled.

Note: The sa me logi c tha t prevents false oscill a-

tor failure interrupts on POR or wake from

Sleep will al so prevent t he detectio n of the

oscillator’s failure to start at all following

these events. This can be avoided by

monitoring the OSTS bit and using a

timing routine to determine if the oscillator

is taking too long to start. Even so, no

oscillator failure interrupt will be flagged.

PIC18F1220/1320

19.5 Program Verification and

Code Protection

The overall structure of the code protection on the

PIC18 Flash devices differs significantly from other

PICmicro devices.

The user p r og ram me mo ry is di vided into three blocks .

One of these is a boot block of 512 bytes. The remain-

der of the memory is divided into two blocks on binary

boundaries.

Each of the three blocks has three protection bits

associated with them. They are:

• Code-Protect bit (CPn)

• Write-Protect bit (WRTn)

• External Block Table Read bit (EBTRn)

Figure 19-5 shows the program memory organization

for 4 and 8-Kbyte de vice s and the specifi c code protec -

tion bit associated with each block. The actual locations

of the bits are summarized in Table 19-3.

FIGURE 19-5: CODE-PROTECTED PROGRAM MEMORY FOR PIC18F1220/1320

TABLE 19-3: SUMMARY OF CODE PROTECTION REGISTERS

Block Code

Protection

Controlled By:

MEMORY SIZE/DEVICE Block Code

Protection

Controlled By:

Address

Range 4Kbytes

(PIC18F1220) 8Kbytes

(PIC18F1320) Address

Range

CPB, WRTB, EBTRB 000000h

0001FFh Boot Block Boot Block 000000h

0001FFh CPB, WRTB, EBTRB

CP0, WRT0, EBTR0 000200h

0007FFh Bloc k 0 Block 0

000200h

CP0, WRT0, EBTR0

CP1, WRT1, EBTR1 000800h

000FFFh Block 1 000FFFh

(Unimplemented

Memory Space)

001000h

Unimplemented

Read ‘0’s

Block 1

001000h

CP1, WRT1, EBTR1

001FFFh

1FFFFFh

Unimplemented

Read ‘0’s

002000h

1FFFFFh

(Unimplemented

Memory Space)

File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

300008h CONFIG5L ——————CP1CP0

300009h CONFIG5H CPD CPB ——————

30000Ah CONFIG6L —————— WRT1 WRT0

30000Bh CONFIG6H WRTD WRTB WRTC —————

30000Ch CONFIG7L —————— EBTR1 EBTR0

30000Dh CONFIG7H — EBTRB ——————

Legend: Shaded cells are uni mp lem en t ed .

PIC18F1220/1320

19.5.1 PROGRAM MEMORY

CODE PROTECTION

The program memory may be read to, or written from,

any location using the table read and table write

instructions. The device ID may be read with table

reads. The configuration registers may be read and

written with the table read and table write instructions.

In normal execution mode, the CPn bits have no direct

effect. CPn bits inhibit external reads and writes. A

block of user memory may be protected from table

writes if the WRTn configuration bit is ‘0’. The EBTRn

bits control table reads. For a block of user memory

with the EBTRn bit set to ‘0’, a table read instruction

that executes from within that block is allowed to read.

A table read instruction that executes from a location

outside of that block is not allowed to read and will

result in reading ‘0’s. Figures 19-6 through 19-8

ill ustrate table write and table read protect ion.

FIGURE 19-6: TABLE WRITE (WRTn) DISALLOWED: PIC18F1320

Note: Code protection bits may only be written to

a ‘0’ from a ‘1’ state. It is not possible to

write a ‘1’ to a bit in the ‘0’ st ate. Code p ro-

tection b its are only set to ‘1’ by a fu ll Chi p

Erase or Block Erase function. The full

Chip Erase and Blo ck Erase func tions can

only be initiated via ICSP or an external

programmer.

000000h

0001FFh

000200h

000FFFh

001000h

001FFFh

WRTB, EBTRB = 11

WRT0, EBTR0 = 01

TBLWT *

TBLPTR = 0002FFh

PC = 0007FEh

TBLWT *

PC = 0017FEh

Results: All table writes disabled to Blockn whenever WRTn = 0.

WRT1, EBTR1 = 11

PIC18F1220/1320

FIGURE 19-7: EXTERNAL BLOCK TABLE READ (EBTRn) DISALLOWED: PIC18F1320

FIGURE 19-8: EXTERNAL BLOCK TABLE READ (EBTRn) ALLOWED: PIC18F1320

000000h

0001FFh

000200h

000FFFh

001000h

001FFFh

WRTB, EBTRB = 11

WRT0, EBTR0 = 10

WRT1, EBTR1 = 11

TBLPTR = 0002FFh

PC = 001FFEh TBLRD *

Results: All table reads from external blocks to Blockn are disabled whenever EBTRn = 0.

TABLAT register returns a value of ‘0’.

000000h

0001FFh

000200h

000FFFh

001000h

001FFFh

WRTB, EBTRB = 11

WRT0, EBTR0 = 10

WRT1, EBTR1 = 11

TBLRD *

TBLPTR = 0002FFh

PC = 0007FEh

Results: Table reads permitte d within Blockn, even when EBTRBn = 0.

TABLAT register returns the value of the data at the location TBLPTR.

PIC18F1220/1320

19.5.2 DATA EEPROM

CODE PROTECTION

The entire data EEPROM is protected from external

reads and writes by two bits: CPD and WRTD. CPD

inhibits external reads and writes of data EEPROM.

WRTD inhibits external writes to data EEPROM. The

CPU can continue to read and write data EEPROM,

regardless of the protection bit settings.

19.5.3 CONFIGURATION REGISTER

PROTECTION

The con figurat ion registers can be write-pro tected. Th e

WRTC bit controls protection of the configuration

registers. In normal execution mode, the WRTC bit is

readable only. WRTC can only be written via ICSP or

an external programmer.

19.6 ID Locations

Eight memory locations (200000h-200007h) are

designated as ID locations, where the user can store

checksum or other code identification numbers. These

locatio ns are b oth read abl e a nd w ri table durin g no rma l

execution through the TBLRD and TBLWT instructions,

or du r ing p r ogr am / ve rif y. Th e ID lo cat io n s c a n be r e ad

when the de vice is code-protected.

19.7 In-Circuit Serial Programming

PIC18F1220/1320 microcontrollers can be serially

progra mmed w hile in t he en d app licati on c ircuit. This i s

simply done with tw o lines for cl ock and data and thre e

other lines for power, ground and the programming

voltage. This allows customers to manufacture boards

with unprogrammed devices and then program the

microcontroller just before shipping the product. This

also allows the most recent firmware or a custom

firmware to be programmed (see Table 19-4).

19.8 In-Circuit Debugger

When the DEBUG bit in configuration register,

CONFIG4L, is programmed to a ‘0’, the In-Circuit

Debugg er fun cti on ali ty is ena ble d. Thi s fun cti on allo w s

simple debugging functions when used with MPLAB®

IDE. When the microcontroller has this feature

enabled, some resources are not available for general

use. Table 19-5 shows which resources are required by

the background debugger.

TABLE 19-5: DEBUGGER RESOURCES

To use the In-Circuit Debugger function of the

microcontroller, the design must implement In-Circuit

Serial Programming connections to MCLR/VPP, VDD,

VSS, RB7 and RB6. This will interface to the In-Circuit

Debu gger modu le avail able from Microchip , or one of the

thir d party developm ent tool compa nies (see th e note fol -

lowing Section 19.7 “In-Circuit Serial Programming”

for mo re in formation).

Note: The Timer1 oscillator shares the T1OSI

and T1OSO pins with the PGD and PGC

pins used for programming and

debugging.

When using the Timer1 oscillator, In-Circuit

Serial Programming (ICSP) may not

function correctly (high voltage or low

voltage), or the In-Circuit Debugger (ICD)

may not communicate with the controller.

As a result of using either ICSP or ICD, the

Timer1 cryst al m ay be dam aged.

If ICSP or ICD operatio ns are requi red, the

crystal should be disconnected from the

circuit (disconne ct either lead ), or insta lled

after programming. The oscillator loading

capacitors may remain in-circuit during

ICSP or ICD operation.

TABLE 19-4: ICSP/ICD CONNECTIONS

Signal Pin Notes

PGD RB7/PGD/T1OSI/

P1D/KBI3 Shared with T1OSC – protect

crystal

PGC RB6/PGC/T1OSO/

T13CKI/P1C/KBI2 Shared with T1OSC – protect

crystal

MCLR MCLR/VPP/RA5

VDD VDD

VSS VSS

PGM RB5/PGM/KBI1 O ptional – pull RB5 low is

LV P enabled

I/O pins: RB6, RB7

Stack: 2 levels

Program Memory: 512 bytes

Data Memory: 10 bytes

PIC18F1220/1320

19.9 Low-Voltage ICSP Programming

The LVP bit in configuration register, CONFIG4L,

enables Low-Voltage Programming (LVP). When LVP

is enabled, the microcontroller can be programmed

without requiring high voltage being applied to the

MCLR/VPP/RA5 pin, but the RB5/PGM/KBI1 pin is then

dedica ted to controll ing Program mo de entry and is not

available as a general purpose I/O pin.

LVP is enabled in erased de vices.

While programming using LVP, VDD is applied to the

MCLR/VPP/RA5 pin as in normal execution mode. To

enter Programming mode, VDD is applied to the PGM

pin.

If Low-V olt age Programming mode will not be used, the

LVP bit can be cleared and RB5/PGM/KBI1 becomes

availa ble as the digi tal I/ O pin RB5. The LVP bit may be

set or cleared only when using standard high-voltage

programm ing (VIHH applied to the MCL R/VPP/RA5 pin).

Once LVP has been disabled, only the standard high-

voltage programming is available and must be used to

program the device.

Memory that is not code-protected can be erased,

using either a Block Erase, or erased row by row, then

written at any spec ified V DD. If co de -protect ed mem ory

is to be erased, a Block Erase is required. If a Block

Erase is to be performed when using Low-Voltage

Programm ing, the dev ice mu st be suppl ied with V DD of

4.5V to 5.5V.

Note 1: High-voltage programming is always

available, regardless of the state of the

LVP bit or the PGM pin, by applying VIHH

to the MCLR pin.

2: When Low-Voltage Programming is

enabled, the RB5 pin can no longer be

used as a general purpose I/O pin.

3: When LVP is enabled, externally pull the

PGM pin to VSS to allow norm al pr ogr am

execution.

PIC18F1220/1320

NOTES:

PIC18F1220/1320

20.0 INSTRUCTION SET SUMMARY

The PIC18 instruction set adds many enhancements to

the previous PICmicro instruction sets, while maintaining

an easy m igration from thes e PICmicro instruc tion set s.

Most instructions are a single program memory word

(16 bits), but there are three instructions that require

two program memory locations.

Each single-word instruction is a 16-bit word divided

into an o pcode, whi ch specifies the instructi on type and

one or more operands, which further specify the

operation of the instruction.

The instruction set is highly orthogonal and is grouped

into four basic categories:

•Byte-oriented operations

•Bit-oriented operations

•Literal operati ons

•Control operations

The PIC18 instruction set summary in Table 20-1 lists

byte-oriented, bit-oriented, literal and control

operations. Table 20-1 shows the opcode field

descriptions.

Most byte-oriented in str uct ions have t hree op erands:

1. The file register (specified by ‘f’)

2. The destination of the result

(specified by ‘d’)

3. The access ed memory

(specified by ‘a’)

The file register designator ‘f’ specifies which file

The destination designator ‘d’ specifies where the

result of the operation is to be placed. If ‘d’ is zero, the

result is placed in the WREG register. If ‘d’ is one, the

result is placed in the file register specified in the

instruction.

All bit-oriented instructions have three operands:

1. The file register (specified by ‘f’)

2. The bit in the file register

(specified by ‘b’)

3. The access ed memory

(specified by ‘a’)

The bit field design ator ‘b’ sele cts the numb er of the bit

affected by the operation, while the file register desig-

nator ‘f’ represents the number of the file in which the

bit is located.

The literal instructions may use some of the following

operands:

• A literal value to be loaded into a file register

(specified by ‘k’)

• The desired FSR r egister to load the literal value

into (specified by ‘f’)

• No operan d requi red

(specified by ‘—’)

The control instruct ions may u se some of t he followin g

operands:

• A program memory address (specified by ‘n’)

• The mode of the CALL or RETURN instructions

(specified by ‘s’)

• The mode of the table read and table write

ins tructions (specif ied by ‘m’)

• No operand requir ed

(specified by ‘—’)

All instructions are a single word, except for three

double-word instructions. These three instructions

were made double-word instructions so that all the

required information i s av ail abl e i n t hes e 3 2 b it s . I n th e

second word, the 4 MSbs are ‘1’s. If this second word

is executed as an instruction (by itself), it will execute

as a NOP.

All single-word instructions are executed in a single

inst ruction cycle, unl ess a conditi onal test is true, or th e

program counter is changed as a result of the instruc-

tion. In th ese cases, the execution takes two i nstruction

cycle s, with the addit ional instru ction cyc le(s) exec uted

as a NOP.

The doub le-word inst ructions exe cute in two ins truction

cycles.

One in struction cycle consist s of f our oscil lator peri ods.

Thus, for an oscillator frequency of 4 MHz, the normal

instruction execution time is 1 μs. If a conditional test is

true, or the program counter is changed as a result of

an instruction, the instruction execution time is 2 μs.

Two-word branch instructions (if true) would take 3 μs.

Figure 20-1 shows the general formats that the

inst ruc t ion s can have .

All examp le s us e the fo rma t ‘nnh’ to represent a hexa-

decimal number, where ‘h’ signifies a hexadecimal

digit.

The Instruction Set Summary, shown in Table 20-1,

lists the instructions recognized by the Microchip

Assembler (MPASMTM). Section 20.2 “Instruction

Set” provides a description of each instruction.

20.1 Read-Modify-Write Operations

Any instruction that specifies a file register as part of

the instruction performs a Read-Modify-Write (R-M-W)

operatio n. The register i s read, the dat a is modifie d and

the result is stored ac cording to ei ther the inst ruction or

the destination designator ‘d’. A read operation is

perfor med on a regi ste r ev en i f the ins truc ti on wr i tes to

that register.

For example, a “BCF PORTB,1” instruction will read

PORTB, clear bit 1 of the data, then write the result

back to PORTB. The read operation would have the

unintended result that any condition that sets the RBIF

flag would be cleared. The R-M-W operation may also

copy the level of an input pin to its corresponding output

latch.

PIC18F1220/1320

TABLE 20-1: OPCODE FIELD DESCRIPTIONS

Field Description

aRAM access bit

a = 0: RAM location in Access RAM (BSR register is ignored)

a = 1: RAM bank is specified by BSR register

bbb Bit address within an 8-bit file register (0 to 7).

BSR Bank Select Register. Used to select the current RAM bank.

dDestination select bit

d = 0: store result in WREG

d = 1: store result in file register f

dest Destination either the WREG register or the specified register file location.

f8-bit register file address (0x00 to 0xFF).

fs 12-bit register file address (0x000 to 0xFFF). This is the source address.

fd 12-bit register file address (0x000 to 0xFFF). This is the destination address.

kLiteral field, constant data or label (may be either an 8-bit, 12-bit or a 20-bit value).

label Label name.

mm The mode of the TBLPTR register for the table read and table write instructions.

Only used with table read and table write instructions:

*No change to register (such as TBLPTR with table reads and writes)

*+ Post-Increment register (suc h as TBLPTR with table reads and writes)

*- Post-Decrement register (such as TBLPTR with table reads and writes)

+* Pre-Increment register (such as TBLPTR with table reads and writes)

nThe relative address (2’s complement number) for relative branch instructions, or the direct address for

call/branch and return instructions.

PRODH Product of Multiply High Byte.

PRODL Product of Multiply Low Byte.

sFast Call/Return mode select bit

s = 0: do not update into/from shadow registers

s = 1: certain registers loaded into/from shadow registers (F ast m ode)

uUnused or unchanged.

WREG Working register (accumulator).

xDon’t care (‘0’ or ‘1’).

The assembler will generate code with x = 0. It is the recommended form of use for compatibility with all

Microchip software tools.

TBLPTR 21-bit Table Pointer (points to a program memory location).

TABLAT 8-bit Table Latch.

TOS Top-of-Stack.

PC Program Counter.

PCL Program Counter Low Byte.

PCH Program Counter High Byte.

PCLATH Program Counter High Byte Latch.

PCLATU Program Counter Upper Byte Latch.

GIE Global Interrupt Enable bit.

WDT Watchdog Timer.

TO Time-out bit.

PD Power-down bit.

C, DC, Z, OV, N ALU Status bits: Carry, Digit Carry, Zero, Overflow, Negative.

[ ] Optional.

( ) Contents.

→Assigned to.

< > Register bit field.

∈In the set of.

italics User defined term (font is Courier).

PIC18F1220/1320

FIGURE 20-1: GENERAL FORMAT FOR INSTRUCTIONS

Byte-oriented file register operations

15 10 9 8 7 0

d = 0 for result destination to be WREG register

OPCODE d a f (FILE #)

d = 1 for result destination to be file register (f)

a = 0 to force Access Bank

Bit-oriented file register operations

15 12 11 9 8 7 0

OPCODE b (BIT #) a f (FILE #)

b = 3-bit position of bit in file register (f)

Literal operations

15 8 7 0

OPCODE k (literal)

k = 8-bit immediate value

Byte to Byte move operations (2-word)

15 12 11 0

OPCODE f (Source FILE #)

CALL, GOTO and Branch operations

15 8 7 0

OPCODE n<7:0> (literal)

n = 20-bit immediate value

a = 1 for BSR to select bank

f = 8-bit file register address

a = 0 to force Acc ess Bank

a = 1 for BSR to select bank

f = 8-bit file register address

15 12 11 0

1111 n<19:8> (literal)

15 12 11 0

1111 f (Destina tion FILE #)

f = 12-bit file register address

Control operations

Example Instruction

ADDWF MYREG, W, B

MOVFF MYREG1, MYREG2

BSF MYREG, bit, B

MOVLW 0x7F

GOTO Label

15 8 7 0

OPCODE n<7:0> (literal)

15 12 11 0

n<19:8> (literal)

CALL MYFUNC

15 11 10 0

OPCOD E n<10:0> ( li t e r a l )

S = Fast bit

BRA MYFUNC

15 8 7 0

OPCODE n<7:0> (literal) BC MYFUNC

PIC18F1220/1320

TABLE 20-1: PIC18FXXXX INSTRUCTION SET

Mnemonic,

Operands Description Cycles 16-Bit Instruction Word Status

Affected Notes

MSb LSb

BYTE-ORIENTED FILE REGISTER OPERATIONS

ADDWF

ADDWFC

ANDWF

CLRF

COMF

CPFSEQ

CPFSGT

CPFSLT

DECF

DECFSZ

DCFSNZ

INCF

INCFSZ

INFSNZ

IORWF

MOVF

MOVFF

MOVWF

MULWF

NEGF

RLCF

RLNCF

RRCF

RRNCF

SETF

SUBFWB

SUBWF

SUBWFB

SWAPF

TSTFSZ

XORWF

f, d , a

f, a

f, d , a

f, a

f, d , a

fs, fd

f, a

f, d , a

f, a

f, d , a

f, a

f, d , a

Add WREG and f

Add WREG and Carry bit to f

AND WREG with f

Clear f

Complement f

Compare f with WREG, skip =

Compare f with WREG, skip >

Compare f with WREG, skip <

Decrement f

Decrement f, Skip if 0

Decrement f, Skip if Not 0

Increment f

Increment f, Skip if 0

Increment f, Skip if Not 0

Inclusive OR WREG with f

Move f

Move fs (source) to 1st word

fd (destination) 2nd word

Move WREG to f

Multiply WREG with f

Negate f

Rotate Left f through Carry

Rotate Left f (No Carry)

Rotate Right f through Carry

Rotate Right f (No Carry)

Set f

Subtract f from WREG with

borrow

Subtract WREG from f

Subtract WREG from f with

borrow

Swap nibble s in f

Test f, skip if 0

Exclusive OR WREG with f

1 (2 or 3)

0010

0001

0110

0001

0110

0000

0010

0100

0010

0011

0100

0001

0101

1100

1111

0110

0000

0110

0011

0100

0011

0100

0110

0101

0011

0110

0001

01da

00da

01da

101a

11da

001a

010a

000a

01da

11da

10da

11da

10da

00da

ffff

111a

001a

110a

01da

00da

100a

01da

11da

10da

011a

10da

ffff

C, DC, Z, OV, N

Z, N

None

C, DC, Z, OV, N

None

C, DC, Z, OV, N

None

Z, N

None

C, DC, Z, OV, N

C, Z, N

Z, N

C, Z, N

Z, N

None

C, DC, Z, OV, N

None

Z, N

1, 2

1,2

1, 2

1, 2, 3, 4

1, 2

1, 2, 3, 4

1, 2

BIT-ORIENTED FILE REGISTER OPERATIONS

BCF

BSF

BTFSC

BTFSS

BTG

f, b , a

f, d , a

Bit Clear f

Bit Set f

Bit Test f, Skip if Clear

Bit Test f, Skip if Set

Bit Toggle f

1 (2 or 3)

1001

1000

1011

1010

0111

bbba

ffff

None

1, 2

3, 4

1, 2

Note 1: When a Port register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that

value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and is

driven low by an external device, the data will be written back with a ‘0’.

2: If this instruction is executed on the TMR0 register (and where applicable, d = 1), the pr escaler will be cleared

if assigned.

3: If Program Coun ter (PC) is mo dified or a c onditional te st is true, th e instructi on requires two cycles. Th e second

cycle is executed as a NOP.

4: Some instructions are 2-word instructions. The second word of these instructions will be executed as a NOP,

unless th e firs t word of the instruct ion r etrieve s the inform ation e mbedd ed in these 16 bit s. T his en sures that al l

program memory locations have a valid instruction.

5: If the table write starts the write cycle to internal memory, the write will continue until terminated.

PIC18F1220/1320

CONTROL OPERATIONS

BNC

BNN

BNOV

BNZ

BOV

BRA

CALL

CLRWDT

DAW

GOTO

NOP

POP

PUSH

RCALL

RESET

RETFIE

RETLW

RETURN

SLEEP

n, s

—

Branch if Carry

Branch if Negat ive

Branch if Not Carry

Branch if Not Negative

Branch if Not Overflow

Branch if Not Zero

Branch if Overflow

Branch Unco nd itio nally

Branch if Zero

Call subroutine 1st word

2nd word

Clear Watchdog Timer

Decimal Adjust WREG

Go to address 1st word

2nd word

No Operation

Pop top of return stack (TOS)

Push top of return stack (TOS)

Relative Call

Software device Reset

Return from interrupt enable

Return with literal in WREG

Return from Subroutine

Go into Standby mode

1 (2)

1110

1101

1110

1111

0000

1110

1111

0000

1111

0000

1101

0000

0010

0110

0011

0111

0101

0001

0100

0nnn

0000

110s

kkkk

0000

1111

kkkk

0000

xxxx

0000

1nnn

0000

1100

0000

nnnn

kkkk

0000

kkkk

0000

xxxx

0000

nnnn

1111

0001

kkkk

0001

0000

nnnn

kkkk

0100

0111

kkkk

0000

xxxx

0110

0101

nnnn

1111

000s

kkkk

001s

0011

None

TO, PD

None

All

GIE/GIEH,

PEIE/GIEL

None

TO, PD

TABLE 20-1: PIC18FXXXX INSTRUCTION SET (CONTINUED)

Mnemonic,

Operands Description Cycles 16-Bit Instruction Word Status

Affected Notes

MSb LSb

Note 1: When a Port register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that

value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and is

driven low by an external device, the data will be written back with a ‘0’.

2: If this instruction is executed on the TMR0 register (and where applicable, d = 1), the pr escaler will be cleared

if assigned.

3: If Program Coun ter (PC) is mo dified or a c onditional te st is true, th e instructi on requires two cycles. Th e second

cycle is executed as a NOP.

4: Some instructions are 2-word instructions. The second word of these instructions will be executed as a NOP,

unless th e firs t word of the instruct ion r etrieve s the inform ation e mbedd ed in these 16 bit s. T his en sures that al l

program memory locations have a valid instruction.

5: If the table write starts the write cycle to internal memory, the write will continue until terminated.

PIC18F1220/1320

LITERAL OPERATIONS

ADDLW

ANDLW

IORLW

LFSR

MOVLB

MOVLW

MULLW

RETLW

SUBLW

XORLW

f, k

Add literal and WREG

AND literal with WREG

Inclusive OR lite ral with WREG

Move literal (12-bit) 2nd word

to FSRx 1st word

Move literal to BSR<3:0>

Move literal to WREG

Multiply literal with WREG

Return with literal in WREG

Subtract WREG from litera l

Exclusive OR literal wi th WREG

0000

1110

1111

0000

1111

1011

1001

1110

0000

0001

1110

1101

1100

1000

1010

kkkk

00ff

kkkk

0000

kkkk

C, DC, Z, OV, N

Z, N

None

C, DC, Z, OV, N

Z, N

DATA MEMORY ↔ PROGRAM MEMORY OPERATIONS

TBLRD*

TBLRD*+

TBLRD*-

TBLRD+*

TBLWT*

TBLWT*+

TBLWT*-

TBLWT+*

Table read

Table r ead with post-increment

Table r ead with post-decrement

Table read with pre- increment

Table write

Table write with post-increment

Table write with post-decrement

Table write with pre-increment

2 (5)

0000

1000

1001

1010

1011

1100

1101

1110

1111

None

TABLE 20-1: PIC18FXXXX INSTRUCTION SET (CONTINUED)

Mnemonic,

Operands Description Cycles 16-Bit Instruction Word Status

Affected Notes

MSb LSb

Note 1: When a Port register is modified as a function of itself (e.g., MOVF PORTB, 1, 0), the value used will be that

value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and is

driven low by an external device, the data will be written back with a ‘0’.

2: If this instruction is executed on the TMR0 register (and where applicable, d = 1), the pr escaler will be cleared

if assigned.

3: If Program Coun ter (PC) is mo dified or a c onditional te st is true, th e instructi on requires two cycles. Th e second

cycle is executed as a NOP.

4: Some instructions are 2-word instructions. The second word of these instructions will be executed as a NOP,

unless th e firs t word of the instruct ion r etrieve s the inform ation e mbedd ed in these 16 bit s. T his en sures that al l

program memory locations have a valid instruction.

5: If the table write starts the write cycle to internal memory, the write will continue until terminated.

PIC18F1220/1320

20.2 Instruction Set

ADDLW ADD literal to W

Syntax: [ label ] ADDLW k

Operands: 0 ≤ k ≤ 255

Operation: (W) + k → W

Status Affected: N, OV, C, DC, Z

Encoding: 0000 1111 kkkk kkkk

Desc ription: The c ontents of W are added to the

8-bit literal ‘k’ and the result is

placed in W.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

literal ‘k’ Process

Data Write to W

Example:ADDLW 0x15

Before Instruction

W = 0x10

After Instruction

W = 0x25

ADDWF ADD W to f

Syntax: [ label ] ADDWF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (W) + (f) → dest

Status Affecte d: N, OV, C, DC, Z

Encoding: 0010 01da ffff ffff

Description: Add W to register ‘f’. If ‘d’ is ‘0’, the

result is store d in W. If ‘d’ is ‘1’, the

result is stored back in register ‘f’

(default). If ‘a’ is ‘0’, the Access

Bank will be selected. If ‘a’ is ‘1’,

the BSR is used.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example:ADDWF REG, W

Before Instruc tio n

W = 0x17

REG = 0xC2

After Instruction

W=0xD9

REG = 0xC2

PIC18F1220/1320

ADDWFC ADD W and Carry bit to f

Syntax: [ label ] ADDWFC f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (W) + (f) + (C) → dest

Status Affected: N, OV, C, DC, Z

Encoding: 0010 00da ffff ffff

Description: Add W, the Carry flag and data

memory location ‘f’. If ‘d’ is ‘0’, the

result is placed in W. If ‘d’ is ‘1’, the

result is placed in data memory

location ‘f’. If ‘a’ is ‘0’, the Access

Bank wil l b e s ele cte d. If ‘a’ is ‘1’, the

BSR will not be overridden.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example:ADDWFC REG, W

Before Instruction

Carry bit = 1

REG = 0x02

W = 0x4D

After Instruction

Carry bit = 0

REG = 0x02

W = 0x50

ANDLW AND literal with W

Syntax: [ label ] ANDLW k

Operands: 0 ≤ k ≤ 255

Operation: (W) .AND. k → W

St at us Af fe cte d: N, Z

Encoding: 0000 1011 kkkk kkkk

Descr iption: The co ntents of W are AND’ed with

the 8-bit literal ‘k’. The result is

placed in W.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read literal

‘k’ Proces s

Data Write to W

Example:ANDLW 0x5F

Before Instruc tio n

W=0xA3

After Instruction

W = 0x03

PIC18F1220/1320

ANDWF AND W with f

Syntax: [ label ] ANDWF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (W) .AND. (f) → dest

Status Affected: N, Z

Encoding: 0001 01da ffff ffff

Desc ription: The co ntents of W are AND’ed with

stored in W. If ‘d’ is ‘1’, the result is

stored back in register ‘f’ (default).

If ‘a’ is ‘0’, the Access Bank will be

selected. If ‘a’ is ‘1’, the BSR will

not be overridden (default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example:ANDWF REG, W

Before Instruction

W = 0x17

REG = 0xC2

After Instruction

W = 0x02

REG = 0xC2

BC Branch if Carry

Syntax: [ label ] BC n

Operands: -128 ≤ n ≤ 127

Operation: if Carry bit is ‘1’

(PC) + 2 + 2n → PC

St at us Af fe cte d: None

Encoding: 1110 0010 nnnn nnnn

Description: If the Carry bit is ‘1’, then the

progr am w ill branc h.

The 2’s complement nu mber ‘2n’ i s

added to the PC. Since the PC will

have incremented to fetch the next

instruc tion, the n ew a ddr ess will be

PC + 2 + 2n. T his instruction is then

a two -cycle instruction.

Words: 1

Cycles: 1(2)

Q Cycle Activity:

If Jump :Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data Write to PC

operation No

operation

If No Jump:

Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data No

operation

Example:HERE BC JUMP

Before Instruc tio n

PC = address (HERE)

After Instruction

If Carry = 1;

PC = address (JUMP)

If Carry = 0;

PC = address (HERE + 2)

PIC18F1220/1320

BCF Bit Clear f

Syntax: [ label ] BCF f,b[,a]

Operands: 0 ≤ f ≤ 255

0 ≤ b ≤ 7

a ∈ [0,1]

Operation: 0 → f

Status Affected: None

Encoding: 1001 bbba ffff ffff

Description: Bit ‘b’ in register ‘f’ is cleared. If ‘a’

is ‘0’, the Access Bank will be

selec ted, over riding the BSR value .

If ‘a’ = 1, then the bank will be

selected as per the BSR value

(default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write

Example:BCF FLAG_REG, 7

Before Instruction

FLAG_REG = 0xC7

After Instruction

FLAG_REG = 0x47

BN Branch if Negative

Syntax: [ label ] BN n

Operands: -128 ≤ n ≤ 127

Operation: if Negative bit is ‘1’

(PC) + 2 + 2n → PC

St at us Af fe cte d: None

Encoding: 1110 0110 nnnn nnnn

Description: If the Negative bit is ‘1’, then the

progr am w ill branc h.

The 2’s complement nu mber ‘2n’ i s

added to the PC. Since the PC will

have incremented to fetch the next

instruc tion, the n ew a ddr ess will be

PC + 2 + 2n. T his instruct ion is then

a two -cycle instruction.

Words: 1

Cycles: 1(2)

Q Cycle Activity:

If Jump :Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data Write to PC

operation No

operation

If No Jump:

Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data No

operation

Example:HERE BN Jump

Before Instruc tio n

PC = address (HERE)

After Instruction

If Negative = 1;

PC = address (Jump)

If Negative = 0;

PC = address (HERE + 2)

PIC18F1220/1320

BNC Branch if Not Carry

Syntax: [ label ] BNC n

Operands: -128 ≤ n ≤ 127

Operation: if Carry bit is ‘0’

(PC) + 2 + 2n → PC

Status Affected: None

Encoding: 1110 0011 nnnn nnnn

Description: If the Carry bit is ‘0’, then the

program will branch.

The 2’s co mp lem en t nu mb er ‘ 2n’ is

added to the PC. Since the PC will

have incremented to fetch the next

instruction, the new address will be

PC + 2 + 2n . This instruct ion is then

a two-cycle instruction.

Words: 1

Cycles: 1(2)

Q Cycle Activity:

If Jump: Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data Write to PC

operation No

operation

If No Jump:

Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data No

operation

Example:HERE BNC Jump

Before Instruction

PC = address (HERE)

After Instruction

If Carry = 0;

PC = address (Jump)

If Carry = 1;

PC = address (HERE + 2)

BNN Branch if Not Negative

Syntax: [ label ] BNN n

Operands: -128 ≤ n ≤ 127

Operation: if Negative bit is ‘0’

(PC) + 2 + 2n → PC

St at us Af fe cte d: None

Encoding: 1110 0111 nnnn nnnn

Description: If the Negative bit is ‘0’, then the

progr am w ill branc h.

The 2’s complement nu mber ‘2n’ i s

added to the PC. Since the PC will

have incremented to fetch the next

instruc tion, the n ew a ddr ess will be

PC + 2 + 2n. T his instruction is then

a two -cycle instruction.

Words: 1

Cycles: 1(2)

Q Cycle Activity:

If Jump :Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data Write to PC

operation No

operation

If No Jump:

Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data No

operation

Example:HERE BNN Jump

Before Instruc tio n

PC = address (HERE)

After Instruction

If Negative = 0;

PC = address (Jump)

If Negative = 1;

PC = address (HERE + 2)

PIC18F1220/1320

BNOV Branch if Not Overflow

Syntax: [ label ] BNOV n

Operands: -128 ≤ n ≤ 127

Operation: if Overflow bit is ‘0’

(PC) + 2 + 2n → PC

Status Affected: None

Encoding: 1110 0101 nnnn nnnn

Description: If the Overfl ow bit is ‘0’, then the

program will branch.

The 2’s co mp lem en t nu mb er ‘ 2n’ is

added to the PC. Since the PC will

have incremented to fetch the next

instruction, the new address will be

PC + 2 + 2n . This instruct ion is then

a two-cycle instruction.

Words: 1

Cycles: 1(2)

Q Cycle Activity:

If Jump: Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data Write to PC

operation No

operation

If No Jump:

Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data No

operation

Example:HERE BNOV Jump

Before Instruction

PC = address (HERE)

After Instruction

If Overflow = 0;

PC = address (Jump)

If Overflow = 1;

PC = address (HERE + 2)

BNZ Branch if Not Zero

Syntax: [ label ] BNZ n

Operands: -128 ≤ n ≤ 127

Operation: if Zero bit is ‘0’

(PC) + 2 + 2n → PC

St at us Af fe cte d: None

Encoding: 1110 0001 nnnn nnnn

Description: If the Zero bit is ‘0’, then the

progr am w ill branc h.

The 2’s complement nu mber ‘2n’ i s

added to the PC. Since the PC will

have incremented to fetch the next

instruc tion, the n ew a ddr ess will be

PC + 2 + 2n. T his instruct ion is then

a two -cycle instruction.

Words: 1

Cycles: 1(2)

Q Cycle Activity:

If Jump :Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data Write to PC

operation No

operation

If No Jump:

Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data No

operation

Example:HERE BNZ Jump

Before Instruc tio n

PC = address (HERE)

After Instruction

If Zero = 0;

PC = address (Jump)

If Zero = 1;

PC = address (HERE + 2)

PIC18F1220/1320

BRA Unconditional Branch

Syntax: [ label ] BRA n

Operands: -1024 ≤ n ≤ 1023

Operation: (PC) + 2 + 2n → PC

Status Affected: None

Encoding: 1101 0nnn nnnn nnnn

Description: Add the 2’s complement number

‘2n’ to the PC. Since the PC will

have incremented to fetch the next

instruction, the new address will be

PC + 2 + 2n. This instruction is a

two-cycle instruction.

Words: 1

Cycles: 2

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data Write to PC

operation No

operation

Example:HERE BRA Jump

Before Instruction

PC = address (HERE)

After Instruction

PC = address (Jump)

BSF Bit Set f

Syntax: [ label ] BSF f,b[,a]

Operands: 0 ≤ f ≤ 255

0 ≤ b ≤ 7

a ∈ [0,1]

Operation: 1 → f

St at us Af fe cte d: None

Encoding: 1000 bbba ffff ffff

Descr iption : Bit ‘b’ in re gister ‘f’ is s et. If ‘a’ is ‘0’,

the Access Bank will be selected,

overridi ng the BSR v alu e. If ‘ a’ = 1,

then the bank will be selected as

per the BSR va lue.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write

Example:BSF FLAG_REG, 7

Before Instruc tio n

FLAG_REG = 0x0A

After Instruction

FLAG_REG = 0x8A

PIC18F1220/1320

BTFSC Bit Test File, Skip if Clear

Syntax: [ label ] BTFSC f,b[,a]

Operands: 0 ≤ f ≤ 255

0 ≤ b ≤ 7

a ∈ [0,1]

Operation: skip if (f) = 0

Status Affected: None

Encoding: 1011 bbba ffff ffff

Description: If bit ‘b’ in register ‘f’ is ‘0’, then the

next instruction is skipped.

If bit ‘b’ is ‘0’, then the next

instruc tio n f etc hed du ring the curren t

instruction execution is discarded

and a NOP is executed instead,

making this a two-cycle instruction. If

‘a’ is ‘0’, the Access Bank will be

selec ted, overriding the BSR value. If

‘a’ = 1, then the bank will be se lecte d

as per the BSR value (default).

Words: 1

Cycles: 1(2)

Note: 3 cycles if skip and followed

by a 2-word instruction.

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data No

operation

If skip: Q1 Q2 Q3 Q4

operation No

operation

If skip and followed by 2-word instruction:

Q1 Q2 Q3 Q4

operation No

operation

operation No

operation

Example:HERE

FALSE

TRUE

BTFSC

FLAG, 1

Before Instruction

PC = address (HERE)

After Instruction

If FLAG<1> = 0;

PC = address (TRUE)

If FLAG<1> = 1;

PC = address (FALSE)

BTFSS Bit Test File, Skip if Set

Syntax: [ label ] BTFSS f,b[,a]

Operands: 0 ≤ f ≤ 255

0 ≤ b < 7

a ∈ [0,1]

Operation: skip if (f) = 1

St at us Af fe cte d: None

Encoding: 1010 bbba ffff ffff

Description: If bit ‘b’ in register ‘f’ is ‘1’, then the

next instruction is skipped.

If bit ‘b’ is ‘1’, then the next

instruc tion fetche d during the cu rrent

instruction execution is discarded

and a NOP is executed instead,

making this a two-cycle instruction. If

‘a’ is ‘0’, the Access Bank will be

selected, overriding the BSR value. If

‘a’ = 1, then the ban k will be s elect ed

as pe r the BSR valu e (defaul t).

Words: 1

Cycles: 1(2)

Note: 3 cycles if skip and followed

by a 2-word instruction.

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data No

operation

If skip: Q1 Q2 Q3 Q4

operation No

operation

If skip and followed by 2-word instruction:

Q1 Q2 Q3 Q4

operation No

operation

operation No

operation

Example:HERE

FALSE

TRUE

BTFSS

FLAG, 1

Before Instruc tio n

PC = address (HERE)

After Instruction

If FLAG<1> = 0;

PC = address (FALSE)

If FLAG<1> = 1;

PC = address (TRUE)

PIC18F1220/1320

BTG Bit Toggle f

Syntax: [ label ] BTG f,b[,a]

Operands: 0 ≤ f ≤ 255

0 ≤ b < 7

a ∈ [0,1]

Operation: (f) → f

Status Affected: None

Encoding: 0111 bbba ffff ffff

Description: Bit ‘b’ in data memory location ‘f’ is

inverte d. If ‘a ’ is ‘0’, th e Ac cess Bank

will be selected, overriding the BSR

value. If ‘ a’ = 1, then the ban k w i ll be

selected as per the BSR value

(default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write

Example:BTG PORTB, 4

Before Instruction:

PORTB = 0111 0101 [0x75]

After Instruction:

PORTB = 0110 0101 [0x65]

BOV Branch if Ov erflow

Syntax: [ label ] BOV n

Operands: -128 ≤ n ≤ 127

Operation: if Overflow bit is ‘1’

(PC) + 2 + 2n → PC

St at us Af fe cte d: None

Encoding: 1110 0100 nnnn nnnn

Description: If the Overflow bit is ‘1’, then the

progr am w ill branc h.

The 2’s complement nu mber ‘2n’ i s

added to the PC. Since the PC will

have incremented to fetch the next

instruc tion, the n ew a ddr ess will be

PC + 2 + 2n. T his instruction is then

a two -cycle instruction.

Words: 1

Cycles: 1(2)

Q Cycle Activity:

If Jump :Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data Write to PC

operation No

operation

If No Jump:

Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data No

operation

Example:HERE BOV JUMP

Before Instruc tio n

PC = address (HERE)

After Instruction

If Overflow = 1;

PC = address (JUMP)

If Overflow = 0;

PC = address (HERE + 2)

PIC18F1220/1320

BZ Branch if Zero

Syntax: [ label ] BZ n

Operands: -128 ≤ n ≤ 127

Operation: if Zero bit is ‘1’

(PC) + 2 + 2n → PC

Status Affected: None

Encoding: 1110 0000 nnnn nnnn

Description: If the Zero bit is ‘1’, then the

program will branch.

The 2’s co mp lem en t nu mb er ‘ 2n’ is

added to the PC. Since the PC will

have incremented to fetch the next

instruction, the new address will be

PC + 2 + 2n . This instruct ion is then

a two-cycle instruction.

Words: 1

Cycles: 1(2)

Q Cycle Activity:

If Jump: Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data Write to PC

operation No

operation

If No Jump:

Q1 Q2 Q3 Q4

Decode Read literal

‘n’ Process

Data No

operation

Example:HERE BZ Jump

Before Instruction

PC = address (HERE)

After Instruction

If Zero = 1;

PC = address (Jump)

If Zero = 0;

PC = address (HERE + 2)

CALL Subroutine Call

Syntax: [ label ] CALL k [,s]

Operands: 0 ≤ k ≤ 1048575

s ∈ [0,1]

Operati on: (PC) + 4 → TOS,

k → PC<20:1>,

if s = 1

(W) → WS,

(Status) → STATUSS,

(BSR) → BSRS

St at us Af fe cte d: None

Encoding:

1st word (k<7:0>)

2nd word(k<19:8>) 1110

1111

110s

k19kkk

k7kkk

kkkk

kkkk0

kkkk8

Description: Subroutine call of entire 2-Mbyte

memory range. First, return

address (PC + 4) is pushed onto

the return stack. If ‘s’ = 1, the W,

Status and BSR registers are also

pushed into their respective

shadow registers, WS, STATUSS

and BSRS. If ‘s’ = 0, no update

occu rs (default). Then, the 20- bit

value ‘k’ is loaded into PC<20:1>.

CALL is a two-cycle instruction.

Words: 2

Cycles: 2

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read literal

‘k’<7:0>, Push PC to

stack Read literal

‘k’<19:8>,

Write to PC

operation No

operation

Example:HERE CALL THERE, FAST

Before Instruc tio n

PC = address (HERE)

After Instruction

PC = address (THERE)

TOS = address (HERE + 4)

WS = W

BSRS = BSR

STATUSS = Status

PIC18F1220/1320

CLRF Clear f

Syntax: [ label ] CLRF f [,a]

Operands: 0 ≤ f ≤ 255

a ∈ [0,1]

Operation: 000h → f

1 → Z

Status Affected: Z

Encoding: 0110 101a ffff ffff

Description: Clears the contents of the specified

Bank w ill be selected, overriding

the BSR value. If ‘a’ = 1, then the

bank will be selected as per the

BSR value (default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write

Example:CLRF FLAG_REG

Before Instruction

FLAG_REG = 0x5A

After Instruction

FLAG_REG = 0x00

CLRWDT Clear Watchdog Timer

Syntax: [ label ] CLRWDT

Operands: None

Operation: 000h → WDT,

000h → WDT postscal er,

1 → TO,

1 → PD

St at us Af fe cte d: TO, PD

Encoding: 0000 0000 0000 0100

Description: CLRWDT instruction resets the

Watchdog Timer. It also resets the

postscaler of the WDT. Status bits,

TO and PD, are set.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode No

operation Process

Data No

operation

Example:CLRWDT

Before Instruc tio n

WDT Counter = ?

After Instruction

WDT Counter = 0x00

WDT Postscaler = 0

TO =1

PD =1

PIC18F1220/1320

COMF Complement f

Syntax: [ label ] COMF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (f) → des t

Status Affected: N, Z

Encoding: 0001 11da ffff ffff

Desc ript ion : The content s of regi ste r ‘f’ are

complemented. If ‘d’ is ‘0’, the

result is store d in W. If ‘d’ is ‘1’, the

result is sto r ed back in register ‘f’

(default). If ‘a’ is ‘0’, the Access

Bank w ill be selected, overriding

the BSR value. If ‘a’ = 1, then the

bank will be selected as per the

BSR value (default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example:COMF REG, W

Before Instruction

REG = 0x13

After Instruction

REG = 0x13

W=0xEC

CPFSEQ Compare f with W, skip if f = W

Syntax: [ label ] CPFSEQ f [,a]

Operands: 0 ≤ f ≤ 255

a ∈ [0,1]

Operation: (f) – (W),

skip if (f) = (W)

(unsign ed comparis on )

St at us Af fe cte d: None

Encoding: 0110 001a ffff ffff

Description: Compares the contents of data

memory location ‘f ’ to the contents

of W by performing an unsigned

subtraction.

If ‘f’ = W, then the fetched

instruction is discarded and a NOP

is execut ed instead, m aking this a

two-cycle instruction. If ‘a’ is ‘0’, the

Access Bank will be selected,

overridi ng the BSR v alu e. If ‘ a’ = 1,

then the bank will be selected as

per the BSR value (default).

Words: 1

Cycles: 1(2)

Note: 3 cycles if skip and followed

by a 2-word instruction.

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data No

operation

If skip: Q1 Q2 Q3 Q4

operation No

operation

If skip and followed by 2-word instruction:

Q1 Q2 Q3 Q4

operation No

operation

operation No

operation

Example:HERE CPFSEQ REG

NEQUAL :

EQUAL :

Before Instruc tio n

PC Address = HERE

W=?

REG = ?

After Instruction

If REG = W;

PC = Address (EQUAL)

If REG ≠ W;

PC = Address (NEQUAL)

PIC18F1220/1320

CPFSGT Compare f with W, skip if f > W

Syntax: [ label ] CPFSGT f [,a]

Operands: 0 ≤ f ≤ 255

a ∈ [0,1]

Operation: (f) – (W),

skip if (f) > (W)

(unsigned comparison)

Status Affected: None

Encoding: 0110 010a ffff ffff

Description: Compares the contents of data

memory location ‘f’ to the contents

of W by performing an unsigned

subtraction.

If the conten ts of ‘f’ are greater t han

the contents of WREG, then the

fetched instruct ion is disca rded and

a NOP is exec uted instead, making

this a two-cycle instruction. If ‘a’ is

‘0’, the Access Bank will be

selec ted, over riding the BSR value .

If ‘a’ = 1, then the bank will be

selected as per the BSR value

(default).

Words: 1

Cycles: 1(2)

Note: 3 cycles if s k ip a nd fo llo w ed

by a 2-word instruction.

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data No

operation

If skip: Q1 Q2 Q3 Q4

operation No

operation

If skip and followed by 2-word instruction:

Q1 Q2 Q3 Q4

operation No

operation

operation No

operation

Example:HERE CPFSGT REG

NGREATER :

GREATER :

Before Instruction

PC = Address (HERE)

W= ?

After Instruction

If REG > W;

PC = Address (GREATER)

If REG ≤ W;

PC = Address (NGREATER)

CPFSLT Compare f with W, skip if f < W

Syntax: [ label ] CPFSLT f [,a]

Operands: 0 ≤ f ≤ 255

a ∈ [0,1]

Operation: (f) – (W),

skip if (f) < (W)

(unsign ed comparis on )

St at us Af fe cte d: None

Encoding: 0110 000a ffff ffff

Description: Compares the contents of data

memory location ‘f ’ to the contents

of W by performing an unsigned

subtraction.

If the contents of ‘f’ are less than

the con tents of W , then the fet che d

instruction is discarded and a NOP

is execut ed instead, m aking this a

two-cycle instruction. If ‘a’ is ‘0’, the

Access Bank will be selected. If ‘a’

is ‘1’, the BSR will not be

overridden (default).

Words: 1

Cycles: 1(2)

Note: 3 cy cl es i f s ki p and fo llowed

by a 2-word instruction.

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data No

operation

If skip: Q1 Q2 Q3 Q4

operation No

operation

If skip and followed by 2-word instruction:

Q1 Q2 Q3 Q4

operation No

operation

operation No

operation

Example:HERE CPFSLT REG

NLESS :

LESS :

Before Instruc tio n

PC = Address (HERE)

W= ?

After Instruction

If REG < W;

PC = Address (LESS)

If REG ≥ W;

PC = Address (NLESS)

PIC18F1220/1320

DAW Decimal Adjust W Register

Syntax: [ label ] DAW

Operands: None

Operation: If [W<3:0> > 9] or [DC = 1] then

(W<3:0>) + 6 → W<3:0>;

else

(W<3:0>) → W<3:0>;

If [W<7:4> > 9] or [C = 1] then

(W<7:4>) + 6 → W<7:4>;

else

(W<7:4>) → W<7 :4>;

Status Affected: C, DC

Encoding: 0000 0000 0000 0111

Description: DAW adjusts the eight-bit value in

W, resulting from the earlier addi-

tion of two variables (each in

packed BCD format) and produces

a correct packed BCD result. Th e

Carry bit may b e set b y DAW reg ard-

less of its setting prior to the DAW

instruction.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write

Example 1:DAW

Before Instruction

W=0xA5

C=0

DC = 0

After Instruction

W = 0x05

C=1

DC = 0

Example 2:

Before Instruction

W=0xCE

C=0

DC = 0

After Instruction

W = 0x34

C=1

DC = 0

DECF Decre ment f

Syntax: [ label ] DECF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (f) – 1 → dest

Status Affected: C, DC, N, OV, Z

Encoding: 0000 01da ffff ffff

Description: Decrement register ‘f’. If ‘d’ is ‘0’,

the result is stored in W. If ‘d’ is ‘1’,

the resu lt is stor ed bac k in regi ste r

‘f’ (default). If ‘a’ is ‘0’, the Access

Bank will be selected, overriding

the BSR value. If ‘a’ = 1, then the

bank will be selected as per the

BSR value (defaul t).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example:DECF CNT

Before Instruc tio n

CNT = 0x01

Z=0

After Instruction

CNT = 0x00

Z=1

PIC18F1220/1320

DECFSZ Decrement f, skip if 0

Syntax: [ label ] DECFSZ f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (f) – 1 → dest,

skip if result = 0

Status Affected: None

Encoding: 0010 11da ffff ffff

Desc ript ion : The content s of regi ste r ‘f’ are

decremented. If ‘d’ is ‘0’, the result

is plac ed in W. If ‘d’ is ‘1’, the result

is pl aced back in register ‘f’

(default).

If the result is ‘0’, the next instruc-

tion, which is already fetched, is

discarded and a NOP is executed

instead, making it a two-cycle

instruction. If ‘a’ is ‘0’, the Access

Bank w ill be selected, overriding

the BSR value. If ‘a’ = 1, then the

bank will be selected as per the

BSR value (default).

Words: 1

Cycles: 1(2)

Note: 3 cycles if skip and followed

by a 2-word instruction.

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

If skip: Q1 Q2 Q3 Q4

operation No

operation

If skip and followed by 2-word instruction:

Q1 Q2 Q3 Q4

operation No

operation

operation No

operation

Example:HERE DECFSZ CNT

GOTO LOOP

CONTINUE

Before Instruction

PC = Address (HERE)

After Instruction

CNT = CNT – 1

If CNT = 0;

PC = Address (CONTINUE)

If CNT ≠0;

PC = Address (HERE + 2)

DCFSNZ Decrement f, skip if not 0

Syntax: [ label ] DCFSNZ f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (f) – 1 → dest,

skip if result ≠ 0

St at us Af fe cte d: None

Encoding: 0100 11da ffff ffff

Description: The contents of register ‘f’ are

decremented. If ‘d’ is ‘0’, the result

is plac ed in W. If ‘d ’ is ‘1’, the result

is pl aced back in register ‘f’

(default).

If the result is not ‘0’, the next

instruction, which is already

fetched, is discarded and a NOP is

executed instead, making it a two-

cycl e instruction. If ‘a ’ is ‘0’, the

Access Bank will be selected,

overridi ng the BSR val ue. If ‘a’ = 1,

then the bank will be selected as

per the BSR value (default).

Words: 1

Cycles: 1(2)

Note: 3 cy c les if sk ip and followed

by a 2-word instruction.

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

If skip: Q1 Q2 Q3 Q4

operation No

operation

If skip and followed by 2-word instruction:

Q1 Q2 Q3 Q4

operation No

operation

operation No

operation

Example:HERE DCFSNZ TEMP

ZERO :

NZERO :

Before Instruc tio n

TEMP = ?

After Instruction

TEMP = TEMP – 1,

If TEMP = 0;

PC = Address (ZERO)

If TEMP ≠0;

PC = Address (NZERO)

PIC18F1220/1320

GOTO Unconditional Branch

Syntax: [ label ] GOTO k

Operands: 0 ≤ k ≤ 1048575

Operation: k → PC<20:1>

Status Affected: None

Encoding:

1st word (k<7:0>)

2nd word(k<19:8>) 1110

1111

k19kkk

k7kkk

kkkk

kkkk0

kkkk8

Description: GOTO allows an unconditional

branch anywhere within the entire

2-Mbyte memory range. The 20-bit

value ‘k’ is loaded into PC<20:1>.

GOTO is always a two-cycle

instruction.

Words: 2

Cycles: 2

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read literal

‘k’<7:0>, No

operation Read literal

‘k’<19:8>,

Write to PC

operation No

operation

Example:GOTO THERE

After Instruction

PC = Address (THERE)

INCF I ncrem ent f

Syntax: [ label ] INCF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (f) + 1 → dest

Status Affected: C, DC, N, OV, Z

Encoding: 0010 10da ffff ffff

Description: The contents of register ‘f’ are

incremented. If ‘d’ is ‘0’, the result

is plac ed in W. If ‘d ’ is ‘1’, th e result

is pl aced back in register ‘f’

(default). If ‘a’ is ‘0’, the Access

Bank will be selected, overriding

the BSR value. If ‘a’ = 1, then the

bank will be selected as per the

BSR value (defaul t).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example:INCF CNT

Before Instruc tio n

CNT = 0xFF

Z=0

C=?

DC = ?

After Instruction

CNT = 0x00

Z=1

C=1

DC = 1

PIC18F1220/1320

INCFSZ Increment f, skip if 0

Syntax: [ label ] INCFSZ f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (f) + 1 → dest,

skip if result = 0

Status Affected: None

Encoding: 0011 11da ffff ffff

Desc ript ion : The content s of regi ste r ‘f’ are

incremented. If ‘d’ is ‘0’, the result

is plac ed in W. If ‘d ’ is ‘1’, th e result

is pl aced back in register ‘f’

(default).

If the result is ‘0’, the next instruc-

tion, which is already fetched, is

discarded and a NOP is executed

instead, making it a two-cycle

instruction. If ‘a’ is ‘0’, the Access

Bank w ill be selected, overriding

the BSR value. If ‘a’ = 1, then the

bank will be selected as per the

BSR value (default).

Words: 1

Cycles: 1(2)

Note: 3 cycl es if skip and followed

by a 2-word instruction.

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

If skip: Q1 Q2 Q3 Q4

operation No

operation

If skip and followed by 2-word instruction:

Q1 Q2 Q3 Q4

operation No

operation

operation No

operation

Example:HERE INCFSZ CNT

NZERO :

ZERO :

Before Instruction

PC = Address (HERE)

After Instruction

CNT = CNT + 1

If CNT = 0;

PC = Address (ZERO)

If CNT ≠0;

PC = Address (NZERO)

INFSNZ Increment f, skip if not 0

Syntax: [ label ] INFSNZ f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (f) + 1 → dest,

skip if result ≠ 0

St at us Af fe cte d: None

Encoding: 0100 10da ffff ffff

Description: The contents of register ‘f’ are

incremented. If ‘d’ is ‘0’, the result

is plac ed in W. If ‘d ’ is ‘1’, th e result

is pl aced back in register ‘f’

(default).

If the result is not ‘0’, the next

instruction, which is already

fetched, is discarded and a NOP is

executed instead, making it a

two-cycle instruction. If ‘a’ is ‘0’, the

Access Bank will be selected, over-

riding th e BSR value. If ‘a’ = 1, th en

the b ank wi ll be selec ted as per th e

BSR value (defaul t).

Words: 1

Cycles: 1(2)

Note: 3 cycles if skip and followed

by a 2-word instruction.

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

If skip: Q1 Q2 Q3 Q4

operation No

operation

If skip and followed by 2-word instruction:

Q1 Q2 Q3 Q4

operation No

operation

operation No

operation

Example:HERE INFSNZ REG

ZERO

NZERO

Before Instruc tio n

PC = Address (HERE)

After Instruction

REG = REG + 1

If REG ≠0;

PC = Address (NZERO)

If REG = 0;

PC = Address (ZERO)

PIC18F1220/1320

IORLW Inclusive OR literal with W

Syntax: [ label ] IORLW k

Operands: 0 ≤ k ≤ 255

Operation: (W) .OR. k → W

Status Affected: N, Z

Encoding: 0000 1001 kkkk kkkk

Description: The contents of W are OR’ed with

the eight-bit literal ‘k’. The result is

placed in W.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

literal ‘k’ Process

Data Write to W

Example:IORLW 0x35

Before Instruction

W = 0x9A

After Instruction

W=0xBF

IORWF Inclusive OR W with f

Syntax: [ label ] IORWF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (W) .OR. (f) → dest

St at us Af fe cte d: N, Z

Encoding: 0001 00da ffff ffff

Description: Inclusive OR W with register ‘f’. If

‘d’ is ‘0’, the result is pla ced in W. If

‘d’ is ‘1’, the result is p laced back in

Access Bank will be selected, over-

riding th e BSR value. If ‘a’ = 1, th en

the bank wi ll be selec ted as p er the

BSR value (defaul t).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example:IORWF RESULT, W

Before Instruc tio n

RESULT = 0x13

W = 0x91

After Instruction

RESULT = 0x13

W = 0x93

PIC18F1220/1320

LFSR Load FSR

Syntax: [ label ] LFSR f,k

Operands: 0 ≤ f ≤ 2

0 ≤ k ≤ 4095

Operation: k → FSRf

Status Affected: None

Encoding: 1110

1111

1110

0000

00ff

k7kkk

k11kkk

kkkk

Desc ription: The 12-bi t literal ‘k’ is loade d into

the file select register pointed to

by ‘f’.

Words: 2

Cycles: 2

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read literal

‘k’ MSB Process

Data W r ite literal

‘k’ MSB to

FSRfH

Decode Read literal

‘k’ LSB Process

Data Write literal

‘k’ to FSRfL

Example:LFSR 2, 0x3AB

After Instruction

FSR2H = 0x03

FSR2L = 0xAB

MOVF Move f

Syntax: [ label ] MOVF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: f → dest

St at us Af fe cte d: N, Z

Encoding: 0101 00da ffff ffff

Description: The contents of register ‘f’ are

moved to a destination dependent

upon the sta t us o f ‘ d’. If ‘d’ is ‘f’, the

result is placed in W. If ‘d’ is ‘f’, the

result is placed back in regi ster ‘f’

(default). Location ‘f’ can be any-

where in the 25 6-b yte bank . If ‘a ’ is

‘0’, the Access Bank will be

selec ted, overri ding the BSR value .

If ‘a’ = 1, then the bank will be

selected as per the BSR value

(default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write W

Example:MOVF REG, W

Before Instruc tio n

REG = 0x22

W=0xFF

After Instruction

REG = 0x22

W = 0x22

PIC18F1220/1320

MOVFF Move f to f

Syntax: [ label ] MOVFF fs,fd

Operands: 0 ≤ fs ≤ 4095

0 ≤ fd ≤ 4095

Operation: (fs) → fd

Status Affected: None

Encoding:

1st word (source)

2nd word (destin.) 1100

1111

ffff

ffffs

ffffd

Description: The contents of source register ‘fs’

are moved to destination register

‘fd’. Location of source ‘fs’ can be

anywhere in the 4096-byte data

space (000h to FFFh) and location

of destination ‘fd’ can also be

anywhere from 000h to FFFh.

Either so urc e or de st ination can be

W (a useful special situat ion).

MOVFF is particularly useful for

transferring a data memory location

to a periph eral register (such as the

transmit buffer or an I/O port).

The MOVFF instruction cannot use

the PCL, T OSU, T OSH or TOSL as

the destination register.

The MOVFF instruction should not

be use d to modi fy in terrupt s etting s

while any interrupt is enabled (see

page 74).

Words: 2

Cycles: 2 (3)

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

(src)

Process

Data No

operation

Decode No

operation

No dummy

read

operation Write

(dest)

Example:MOVFF REG1, REG2

Before Instruction

REG1 = 0x33

REG2 = 0x11

After Instruction

REG1 = 0x33,

REG2 = 0x33

MOVLB M ove literal to low nibble in BSR

Syntax: [ label ] MOVLB k

Operands: 0 ≤ k ≤ 255

Operation: k → BSR

St at us Af fe cte d: None

Encoding: 0000 0001 kkkk kkkk

Description: The 8-bit literal ‘k’ is loaded into

the Bank Select Register (BSR).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read literal

‘k’ Proces s

Data Write

literal ‘k’ to

BSR

Example:MOVLB 5

Before Instruc tio n

BSR register = 0x02

After Instruction

BSR register = 0x05

PIC18F1220/1320

MOVLW Move literal to W

Syntax: [ label ] MOVLW k

Operands: 0 ≤ k ≤ 255

Operation: k → W

Status Affected: None

Encoding: 0000 1110 kkkk kkkk

Description: The eight-bit literal ‘k’ is loaded

into W.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

literal ‘k’ Process

Data Write to W

Example:MOVLW 0x5A

After Instruction

W = 0x5A

MOVWF Move W to f

Syntax: [ label ] MOVWF f [,a]

Operands: 0 ≤ f ≤ 255

a ∈ [0,1]

Operation: (W) → f

St at us Af fe cte d: None

Encoding: 0110 111a ffff ffff

Description: Move data from W to register ‘f’.

Location ‘f’ can be anywher e in the

256-byte bank. If ‘a’ is ‘0’, the

Access Bank will be selected, over-

riding th e BSR value. If ‘a’ = 1, th en

the b ank wi ll be selec ted as per th e

BSR value (defaul t).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write

Example:MOVWF REG

Before Instruc tio n

W = 0x4F

REG = 0xFF

After Instruction

W = 0x4F

REG = 0x4F

PIC18F1220/1320

MULLW Multiply Literal with W

Syntax: [ label ] MULLW k

Operands: 0 ≤ k ≤ 255

Operati on: (W) x k → PRODH:PRODL

Status Affected: None

Encoding: 0000 1101 kkkk kkkk

Description: An unsigned multiplication is

carried out be tween the conte nts

of W and the 8-bit literal ‘k’. The

16-bit result is placed in the

PRODH:PRODL register pair.

PRODH contains the high byte.

W is unchanged.

None of t he Status flags are

affected.

Note that neither Overflow nor

Carry is possible in this opera-

tion. A Zero resu lt is possi ble but

not detected.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

literal ‘k’ Process

Data Write

registers

PRODH:

PRODL

Example:MULLW 0xC4

Before Instruction

W=0xE2

PRODH = ?

PRODL = ?

After Instruction

W=0xE2

PRODH = 0xAD

PRODL = 0x08

MULWF Mult iply W with f

Syntax: [ label ] MULWF f [,a]

Operands: 0 ≤ f ≤ 255

a ∈ [0,1]

Operation: (W) x (f) → PRODH:PRODL

St at us Af fe cte d: None

Encoding: 0000 001a ffff ffff

Description: An unsigned multiplication is

carried o ut betw een the content s

of W and the reg ister file location

‘f’. The 16-bit result is stored in

the P RODH :PROD L regi ster

pair . PRODH contains the high

byte.

Both W and ‘f’ are unchanged.

None of the Status flags are

affected.

Note that neither Overflow nor

Carry is possible in this opera-

tion. A Zero result is possible,

but not detected. If ‘a’ is ‘0’, the

Access Bank will be selected,

overriding the BSR value. If

‘a’ = 1, then the bank will be

selected as per the BSR value

(default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write

registers

PRODH:

PRODL

Example:MULWF REG

Before Instruc tio n

W=0xC4

REG = 0xB5

PRODH = ?

PRODL = ?

After Instruction

W=0xC4

REG = 0xB5

PRODH = 0x8A

PRODL = 0x94

PIC18F1220/1320

NEGF Negate f

Syntax: [ label ] NEGF f [,a]

Operands: 0 ≤ f ≤ 255

a ∈ [0,1]

Operation: (f) + 1 → f

Status Affected: N, OV, C, DC, Z

Encoding: 0110 110a ffff ffff

Description: Location ‘f’ is negated using two’s

compl ement. The re sult is pla ced in

the dat a mem ory loca tio n ‘f’. If ‘a ’ is

‘0’, the Access Bank will be

selec ted, over riding the BSR value .

If ‘a’ = 1, then the bank will be

selected as per the BSR value.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write

Example:NEGF REG, 1

Before Instruction

REG = 0011 1010 [0x3A]

After Instruction

REG = 1100 0110 [0xC6]

NOP No Operation

Syntax: [ label ] NOP

Operands: None

Operation: No operation

St at us Af fe cte d: None

Encoding: 0000

1111

0000

xxxx

0000

xxxx

0000

xxxx

Description: No operation.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode No

operation No

operation

Example:

None.

PIC18F1220/1320

POP Pop Top of Return Stack

Syntax: [ label ] POP

Operands: None

Operation: (TOS) → bit bucket

Status Affected: None

Encoding: 0000 0000 0000 0110

Description: The TOS value is pulled off the

return stack and is discarded. The

TOS value then becomes the

previous value th at was pushed

onto the return stack.

This instruction is provided to

enable the user to properly manage

the return stack to incorporate a

software stack.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode No

operation Pop TOS

value No

operation

Example:POP

GOTO NEW

Before Instruction

TOS = 0x0031A2

Stack (1 level down) = 0x014332

After Instruction

TOS = 0x014332

PC = NEW

PUSH Push Top of Return Stack

Syntax: [ label ] PUSH

Operands: None

Operati on: (PC + 2) → TOS

St at us Af fe cte d: None

Encoding: 0000 0000 0000 0101

Description: The PC + 2 is pushed onto the top

of the return stack. The previous

TOS value is pushed down on the

stack.

This instruction allows implement-

ing a software stack by modifying

TOS and then pushing it onto the

return stack.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Push

PC + 2 onto

return stack

operation No

operation

Example:PUSH

Before Instruc tio n

TOS = 0x00345A

PC = 0x000124

After Instruction

PC = 0x000126

TOS = 0x000126

Stack (1 level down) = 0x00345A

PIC18F1220/1320

RCALL Relative Call

Syntax: [ label ] RCALL n

Operands: -1024 ≤ n ≤ 1023

Operation: (PC) + 2 → TOS,

(PC) + 2 + 2n → PC

Status Affected: None

Encoding: 1101 1nnn nnnn nnnn

Description: Subroutine call with a jump up to 1K

from the current location. First,

return address (PC + 2) is pushed

onto the stack. Then, add the 2’s

compl ement number ‘2n’ to the PC.

Since t he PC will hav e incremented

to fetch the next instruction, the new

address will be PC + 2 + 2n. This

instruction is a two-cycle instruction.

Words: 1

Cycles: 2

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read literal

‘n’

Push PC to

stack

Process

Data Write to PC

operation No

operation

Example:HERE RCALL Jump

Before Instruction

PC = Address (HERE)

After Instruction

PC = Address (Jump)

TOS = Address (HERE + 2)

RESET Reset

Syntax: [ label ] RESET

Operands: None

Operation: Reset all registers and flags that

are affect ed by a MCLR Reset.

St at us Af fe cte d: All

Encoding: 0000 0000 1111 1111

Description: This instruction provides a way to

execute a MCLR Reset in software.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Start

Reset No

operation No

operation

Example:RESET

After Instruction

Registers = Reset Value

Flags* = Reset Value

PIC18F1220/1320

RETFIE Return from Interrupt

Syntax: [ label ] RETFIE [s]

Operands: s ∈ [0,1]

Operation: (TOS) → PC,

1 → GIE/GIEH or PEIE/GIEL,

if s = 1

(WS) → W,

(STATUSS) → Status,

(BSRS) → BSR,

PCLATU, PCLATH are unchanged.

Status Affected: GIE/GIEH, PEIE/GIEL.

Encoding: 0000 0000 0001 000s

Description: Return from interrupt. Stack is

popped and Top-of-Stack (TOS) is

loaded into the PC. Interrupts are

enabled by setting either the high

or low priority global interrupt

enable bit. If ‘s’ = 1, the contents of

the shadow registers, WS,

STATUSS and BSRS, are loaded

into their corresponding registers,

W, Status and BSR. If ‘s’ = 0, no

update of these registers occurs

(default).

Words: 1

Cycles: 2

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode No

operation No

operation Pop PC

from stack

Set GIEH or

GIEL

operation No

operation

Example:RETFIE 1

After Interrupt

PC = TOS

W=WS

BSR = BSRS

Status = STATUSS

GIE/ GIEH, PEIE/GIEL = 1

RETLW Return Literal to W

Syntax: [ label ] RETLW k

Operands: 0 ≤ k ≤ 255

Operation: k → W,

(TOS) → PC,

PCLATU, PCLATH are unchanged

St at us Af fe cte d: None

Encoding: 0000 1100 kkkk kkkk

Descr ipti on : W is loaded w ith the e igh t-bi t lit eral

‘k’. The program counter is loaded

from the top of t he st ack (the retu rn

address) . The high address latch

(PCLATH) remains unchanged.

Words: 1

Cycles: 2

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

literal ‘k’ Process

Data Pop PC

from stack,

Write to W

operation No

operation

Example:

CALL TABLE ; W contains table

; offset value

; W now has

; table value

TABLE

ADDWF PCL ; W = offset

RETLW k0 ; Begin table

RETLW k1 ;

RETLW kn ; End of table

Before Instruc tio n

W = 0x07

After Instruction

W = value of kn

PIC18F1220/1320

RETURN Return from Subroutine

Syntax: [ label ] RETURN [s]

Operands: s ∈ [0,1]

Operation: (TOS) → PC,

if s = 1

(WS) → W,

(STATUSS) → Status,

(BSRS) → BSR,

PCLATU, PCLATH are unchanged

Status Affected: None

Encoding: 0000 0000 0001 001s

Description: Return from subroutine. The stack

is popped and the top of the stack

is loaded into the program counter.

If ‘s ’= 1, the content s of th e shadow

registers, WS, STATUSS and

BSRS, are loaded into their corre-

sponding registers, W, Status and

BSR. If ‘s’ = 0, no update of these

registers occurs (default).

Words: 1

Cycles: 2

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode No

operation Process

Data Pop PC

from stack

operation No

operation

Example:RETURN

After Interrupt

PC = TOS

RLCF Rotate Left f through Carry

Syntax: [ label ] RLCF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (f<n>) → dest<n + 1>,

(f<7>) → C,

St at us Af fe cte d: C, N, Z

Encoding: 0011 01da ffff ffff

Description: The contents of register ‘f ’ are

rotated one bit to the left through

the Carry flag. If ‘d’ is ‘0’, the resu lt

is place d in W . If ‘d’ is ‘1’, the result

is stored back in register ‘f’

(default). If ‘a’ is ‘0’, the Access

Bank will be selected, overriding

the BSR value. If ‘a’ = 1, then the

bank will be selected as per the

BSR value (default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example:RLCF REG, W

Before Instruc tio n

REG = 1110 0110

C=0

After Instruction

REG = 1110 0110

W=1100 1100

C=1

Cregister f

PIC18F1220/1320

RLNCF Rotate Left f (no carry)

Syntax: [ label ] RLNCF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (f<n>) → dest<n + 1>,

(f<7>) → dest<0>

Status Affected: N, Z

Encoding: 0100 01da ffff ffff

Description: The contents of register ‘f’ are

rotate d one bit to th e left. If ‘d’ is ‘0’,

the resul t is plac ed in W. If ‘d ’ is ‘1’,

the result is stored back in register

‘f’ (default). If ‘a’ is ‘0’, the Access

Bank will be selected, overriding

the BSR value. If ‘a’ is ‘1’, then the

bank will be selected as per the

BSR value (default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example:RLNCF REG

Before Instruction

REG = 1010 1011

After Instruction

REG = 0101 0111

RRCF Rot ate Right f through Carry

Syntax: [ label ] RRCF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (f<n>) → dest<n – 1>,

(f<0>) → C,

Status Affecte d: C, N, Z

Encoding: 0011 00da ffff ffff

Description: The contents of register ‘f’ are

rotated one bit to the right through

the Carry flag. If ‘d’ is ‘0’, the result

is plac ed in W. If ‘d ’ is ‘1’, th e result

is pl aced back in register ‘f’

(default). If ‘a’ is ‘0’, the Access

Bank will be selected, overriding

the BSR value. If ‘a’ is ‘1’, then the

bank will be selected as per the

BSR value (defaul t).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example:RRCF REG, W

Before Instruc tio n

REG = 1110 0110

C=0

After Instruction

REG = 1110 0110

W=0111 0011

C=0

Cregister f

PIC18F1220/1320

RRNCF Rotate Right f (no carry)

Syntax: [ label ] RRNCF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (f<n>) → dest<n – 1>,

(f<0>) → dest<7>

Status Affected: N, Z

Encoding: 0100 00da ffff ffff

Desc ript ion : The content s of regi ste r ‘f’ are

rotated one bit to the right. If ‘d’ is

‘0’, the res ult is pl aced in W. If ‘d ’ is

‘1’, the result is placed back in

Access Bank will be selected,

overriding the BSR value. If ‘a’ is

‘1’, then the bank will be selected

as per the BSR value (default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example 1:RRNCF REG, 1, 0

Before Instruction

REG = 1101 0111

After Instruction

REG = 1110 1011

Example 2:RRNCF REG, W

Before Instruction

W=?

REG = 1101 0111

After Instruction

W=1110 1011

REG = 1101 0111

SETF Set f

Syntax: [ label ] SETF f [,a]

Operands: 0 ≤ f ≤ 255

a ∈ [0,1]

Operation: FFh → f

St at us Af fe cte d: None

Encoding: 0110 100a ffff ffff

Description: The contents of the specified

the Access Bank will be selected,

overriding the BSR value. If ‘a’ is

‘1’, then the bank will be selected

as pe r the BSR valu e (defaul t).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write

Example:SETF REG

Before Instruc tio n

REG = 0x5A

After Instruction

REG = 0xFF

PIC18F1220/1320

SLEEP Enter Sleep mode

Syntax: [ label ] SLEEP

Operands: None

Operation: 00h → WDT,

0 → WDT postscaler,

1 → TO,

0 → PD

Status Affected: TO, PD

Encoding: 0000 0000 0000 0011

Description: The Power-down status bit (PD) is

cleared. The Time-out status bit

(TO) is set. The Watchdog Timer

and its postscaler are cleared.

The processor is put into Sleep

mode with the oscillator stopped.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode No

operation Process

Data Go to

Sleep

Example:SLEEP

Before Instruction

TO =?

PD =?

After Instruction

TO =1 †

PD =0

† If WDT causes wake-up, this bit is cleared.

SUBFWB Subtract f from W with borrow

Syntax: [ label ] SUBFWB f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (W) – (f) – (C) → dest

Status Affected: N, OV, C, DC, Z

Encoding: 0101 01da ffff ffff

Description: Subtract register ‘f’ and Carry flag

(borrow) from W (2’s complement

method). If ‘d’ is ‘0’, the result is

stored in W. If ‘d’ is ‘1’, the result is

stored in register ‘f’ (default). If ‘a’ is

‘0’, the Access Bank will be

selected, overriding the BSR value.

If ‘a’ is ‘1’, then the bank will be

selected as per the BSR value

(default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example 1:SUBFWB REG

Before Instruc tio n

REG = 0x03

W = 0x02

C = 0x01

After Instruction

REG = 0xFF

W = 0x02

C = 0x00

Z = 0x00

N = 0x01 ; res ult is negative

Example 2:SUBFWB REG, 0, 0

Before Instruc tio n

REG = 2

W=5

C=1

After Instruction

REG = 2

W=3

C=1

Z=0

N = 0 ; result is positive

Example 3:SUBFWB REG, 1, 0

Before Instruc tio n

REG = 1

W=2

C=0

After Instruction

REG = 0

W=2

C=1

Z=1; result is zero

N=0

PIC18F1220/1320

SUBLW Subtract W from literal

Syntax: [ label ]SUBLW k

Operands: 0 ≤ k ≤ 255

Operation: k – (W) → W

Status Affected: N, OV, C, DC, Z

Encoding: 0000 1000 kkkk kkkk

Descriptio n: W is subtracted from the ei ght-bit

literal ‘k’. The result is placed

in W.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

literal ‘k’ Process

Data Write to W

Example 1: SUBLW 0x02

Before Instruction

W=1

C=?

After Instruction

W=1

C = 1 ; result is positive

Z=0

N=0

Example 2:SUBLW 0x02

Before Instruction

W=2

C=?

After Instruction

W=0

C = 1 ; result is zero

Z=1

N=0

Example 3:SUBLW 0x02

Before Instruction

W=3

C=?

After Instruction

W = F F ; (2’s complement)

C = 0 ; result is negative

Z=0

N=1

SUBWF Subtract W from f

Syntax: [ label ] SUBWF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operati on: (f) – (W) → dest

Status Affected: N, OV, C, DC, Z

Encoding: 0101 11da ffff ffff

Description: Subtract W from register ‘f’ (2’s

complement method). If ‘d’ is ‘0’,

the result is stored in W. If ‘d’ is

‘1’, the result is stored back in

Access Bank will be selected,

overriding the BSR value. If ‘a’ is

‘1’, then the bank will be selected

as per the BSR value (default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example 1:SUBWF REG

Before Instruc tio n

REG = 3

W=2

C=?

After Instruction

REG = 1

W=2

C = 1 ; result is positive

Z=0

N=0

Example 2:SUBWF REG, W

Before Instruc tio n

REG = 2

W=2

C=?

After Instruction

REG = 2

W=0

C=1; result is zero

Z=1

N=0

Example 3:SUBWF REG

Before Instruc tio n

REG = 0x01

W = 0x02

C=?

After Instruction

REG = 0xFFh ;(2’s complement)

W = 0x02

C = 0x00 ;result is negative

Z = 0x00

N = 0x01

PIC18F1220/1320

SUBWFB Subtract W from f with Borrow

Syntax: [ label ] SUBWFB f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (f) – (W) – (C) → dest

Status Affected: N, OV, C, DC, Z

Encoding: 0101 10da ffff ffff

Description: Subtract W and the Carry flag

(borrow) from register ‘f’ (2’s comple-

ment method). If ‘d’ is ‘0’, the result is

stored in W. If ‘d’ is ‘1’, the result is

stored back in register ‘f’ (default). If

‘a’ is ‘0’, the Access Bank will be

selected, overriding the BSR value. If

‘a’ is ‘1’, then the bank will be

selected as per the BSR value

(default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example 1:SUBWFB REG, 1, 0

Before Instruction

REG = 0x19 (0001 1001)

W= 0x0D (0000 1101)

C = 0x01

After Instruction

REG = 0x0C (0000 1011)

W= 0x0D (0000 1101)

C = 0x01

Z = 0x00

N = 0x00 ; result is positive

Example 2: SUBWFB REG, 0, 0

Before Instruction

REG = 0x1B (0001 1011)

W= 0x1A (0001 1010)

C = 0x00

After Instruction

REG = 0x1B (0001 1011)

W = 0x00

C = 0x01

Z = 0x01 ; result is zero

N = 0x00

Example 3: SUBWFB REG, 1, 0

Before Instruction

REG = 0x03 (0000 0011)

W= 0x0E (0000 1101)

C = 0x01

After Instruction

REG = 0xF5 (1111 0100)

; [2’s co mp]

W= 0x0E (0000 1101)

C = 0x00

Z = 0x00

N = 0x01 ; result is negative

SWAPF Swap f

Syntax: [ label ] SWAPF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (f<3:0>) → dest<7:4>,

(f<7:4>) → dest<3:0>

St at us Af fe cte d: None

Encoding: 0011 10da ffff ffff

Description: The upper and lower nibbles of

‘0’, the res ult is pl aced in W. If ‘d’ is

‘1’, the resul t is p laced in reg ister ‘f’

(default). If ‘a’ is ‘0’, the Access

Bank will be selected, overriding

the BSR value. If ‘a’ is ‘1’, then the

bank will be selected as per the

BSR value (defaul t).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example:SWAPF REG

Before Instruc tio n

REG = 0x53

After Instruction

REG = 0x35

PIC18F1220/1320

TBLRD Table Read

Syntax: [ label ] TBLRD ( *; *+; *-; +*)

Operands: None

Operation: if TBLRD *,

(Prog Mem (TBLPTR)) → TABLAT;

TBLPTR – No Change;

if TBLRD *+,

(Prog Mem (TBLPTR)) → TABLAT;

(TBLPTR) + 1 → TBLPTR;

if TBLRD *-,

(Prog Mem (TBLPTR)) → TABLAT;

(TBLPTR) – 1 → TBLPTR;

if TBLRD +*,

(TBLPTR) + 1 → TBLPTR;

(Prog Mem (TBLPTR)) → TABLAT;

Status Affected: None

Encoding: 0000 0000 0000 10nn

nn = 0*

= 1*+

= 2*-

= 3+*

Description: This instruction is us ed to read the

contents of Program Memory (P.M.). To

address the program memory , a pointer

called Table Pointer (TBLPTR) is used.

The TBLPTR (a 21-bit pointer) points

to each byte in the program memory.

TBLPTR has a 2-Mbyte address

range.

TBLPTR [0] = 0: Least Significant

Byte of Program

Memory Word

TBLPTR [0] = 1: Most Significant

Byte of Program

Memory Word

The TBLRD instruction can modify the

value of TBLPTR as follows:

• no change

• post-increment

• post-decrement

• pre-increment

Words: 1

Cycles: 2

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode No

operation No

operation

operation No operation

(Read Program

Memory)

operation No operati on

(Writ e

TABLAT)

TBLRD Table Rea d (Continued)

Example 1:TBLRD *+ ;

Before Instruc tio n

TABLAT = 0x55

TBLPTR = 0x00A356

MEMORY(0x00A356) = 0x34

After Instruction

TABLAT = 0x34

TBLPTR = 0x00A357

Example 2:TBLRD +* ;

Before Instruc tio n

TABLAT = 0xAA

TBLPTR = 0x01A357

MEMORY(0x01A357) = 0x12

MEMORY(0x01A358) = 0x34

After Instruction

TABLAT = 0x34

TBLPTR = 0x01A358

PIC18F1220/1320

TBLWT Table Write

Syntax: [ label ] TBLWT ( *; *+; *-; +*)

Operands: None

Operation: if TBLWT*,

(TABLAT) → Holding Register;

TBLPTR – No Change;

if TBLWT*+,

(TABLAT) → Holding Register;

(TBLPTR) + 1 → TBLPTR ;

if TBLWT*-,

(TABLAT) → Holding Register;

(TBLPTR) – 1 → TBLP TR;

if TBLWT+*,

(TBLPTR) + 1 → TBLPTR ;

(TABLAT) → Holding Register;

Status Affected: None

Encoding: 0000 0000 0000 11nn

nn = 0*

= 1*+

= 2*-

= 3+*

Description: This instruction uses the 3 LSBs of

TBLPTR to determine which of the

8 holding registers the TABL AT is

written to. The holding registers are

used to program the co nten ts of

Program Memory (P.M.). (Refer

to Section 6.0 “Flash Program

Memory” for additional details on

programming Flash memory.)

The TBLPTR (a 21-bit pointer) points

to each byte in the program memory.

TBLPTR has a 2-Mbyte address

range. The LSb of the TBLPTR

selects which byte of the program

memory location to access.

TBLPTR[0] = 0:Least Significant

Byte of Program

Memory Word

TBLPTR[0] = 1:Most Significant

Byte of Program

Memory Word

The TBLWT instruction ca n modify the

value of TBLPTR as follows:

• no chang e

• post-increment

• post-decrement

• pre-increment

TBLWT Table Write (Continued)

Words: 1

Cycles: 2

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode No

operation No

operation

operation No

operation

(Read

TABLAT)

operation No

operation

(Write to

Holding

Example 1:TBLWT *+;

Before Instruc tio n

TABLAT = 0x55

TBLPTR = 0x00A356

HOLD ING REGIST ER

(0x00A356) = 0xFF

After Instructions (table write completion)

TABLAT = 0x55

TBLPTR = 0x00A357

HOLD ING REGIST ER

(0x00A356) = 0x55

Example 2:TBLWT +*;

Before Instruc tio n

TABLAT = 0x34

TBLPTR = 0x01389A

HOLD ING REGIST ER

(0x01389A) = 0xFF

HOLD ING REGIST ER

(0x01389B) = 0xFF

After Instruction (table write completion)

TABLAT = 0x34

TBLPTR = 0x01389B

HOLD ING REGIST ER

(0x01389A) = 0xFF

HOLD ING REGIST ER

(0x01389B) = 0x34

PIC18F1220/1320

TSTFSZ Test f, skip if 0

Syntax: [ label ] TSTFSZ f [,a]

Operands: 0 ≤ f ≤ 255

a ∈ [0,1]

Operation: skip if f = 0

Status Affected: None

Encoding: 0110 011a ffff ffff

Description: If ‘f’ = 0, the nex t inst ruct io n,

fetched during the current

instruction execution is discarded

and a NOP is exec uted, m aking this

a two-cycle instruction. If ‘a’ is ‘0’,

the Access Bank will be selected,

overriding the BSR value. If ‘a’ is

‘1’, then the bank will be selected

as per the BSR value (default).

Words: 1

Cycles: 1(2)

Note: 3 cycles if skip and followed

by a 2-word instruction.

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data No

operation

If skip: Q1 Q2 Q3 Q4

operation No

operation

If skip and followed by 2-word instruction:

Q1 Q2 Q3 Q4

operation No

operation

operation No

operation

Example:HERE TSTFSZ CNT

NZERO :

ZERO :

Before Instruction

PC = Address (HERE)

After Instruction

If CNT = 0x00,

PC = Address (ZERO)

If CNT ≠0x00,

PC = Address (NZERO)

XORLW Exclusive OR literal with W

Syntax: [ label ] XORLW k

Operands: 0 ≤ k ≤ 255

Operation: (W) .XOR. k → W

St at us Af fe cte d: N, Z

Encoding: 0000 1010 kkkk kkkk

Description: The contents of W are XOR’ed

with the 8-bit literal ‘k’. The result

is placed in W.

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

literal ‘k’ Process

Data Write to W

Example:XORLW 0xAF

Before Instruc tio n

W=0xB5

After Instruction

W = 0x1A

PIC18F1220/1320

XORWF Exclusive OR W with f

Syntax: [ label ] XORWF f [,d [,a]]

Operands: 0 ≤ f ≤ 255

d ∈ [0,1]

a ∈ [0,1]

Operation: (W) .XOR. (f) → dest

Status Affected: N, Z

Encoding: 0001 10da ffff ffff

Description: Exclusive OR the contents of W

with register ‘f’. If ‘d’ is ‘0’, the result

is stored in W. If ‘d’ is ‘1’, the result

is stored bac k in t he regi ste r ‘f’

(default). If ‘a’ is ‘0’, the Access

Bank w ill be selected, overriding

the BSR value. If ‘a’ is ‘1’, then the

bank will be selected as per the

BSR value (default).

Words: 1

Cycles: 1

Q Cycle Activity:

Q1 Q2 Q3 Q4

Decode Read

Data Write to

destination

Example:XORWF REG

Before Instruction

REG = 0xAF

W=0xB5

After Instruction

REG = 0x1A

W=0xB5

PIC18F1220/1320

21.0 DEVELOPMENT SUPPORT

The PICmicro® microcontrollers are supported with a

full ran ge of hardware a nd softwa re develo pment to ols:

• Integrated Development Environment

- MPLAB® IDE Software

• Assemblers/Compilers/Linkers

- MPASMTM Assembler

- MPLAB C17 and MPLAB C18 C Compilers

-MPLINK

TM Object Linker/

MPLIBTM Object Librarian

- MPLAB C30 C Compiler

- MPLAB ASM30 Assembler/Linker/Library

• Simulators

- MPLAB SIM Software Simulator

- MPLAB dsPIC30 Software Simulator

•Emulators

- MPLAB ICE 2000 In-Circuit Emulator

- MPLAB ICE 4000 In-Circuit Emulator

• In-Circuit Debugger

- MPLAB ICD 2

• Device Progra mmers

-PRO MATE

® II Universa l D evi ce P rogramm er

- PICSTART® Plus Development Programmer

- MPLAB PM3 Device Programmer

• Low-Cost Demonstration Boards

- PICDEMTM 1 Demonstration Board

- PICDEM.netTM De monstration Board

- PICDEM 2 Plus Demonstration Board

- PICDEM 3 Demonstration Board

- PICDEM 4 Demonstration Board

- PICDEM 17 Demonstration Board

- PICDEM 18R Demonstration Board

- PICDEM LIN Demonstration Board

- PICDEM USB Demonstration Board

• Evaluation Kits

-K

EELOQ® Evaluation and Programming Tools

- P ICDEM MSC

-microID

® Developer Kits

-CAN

- PowerSmart® Developer Kits

-Analog

21.1 MPLAB Integrated Development

Environment Software

The MPLAB IDE software brings an ease of software

development previously unseen in the 8/16-bit micro-

controller market. The MPLAB IDE is a Windows®

based application that contains:

• An interface to debugging t ools

- simulator

- programmer (sold separately)

- emulator (sold separately)

- in-circuit debugger (sold separately)

• A full-featured editor with color coded context

• A multiple project manager

• Customizable data windows with direct edit of

contents

• High-level source code debugging

• Mouse over variable inspection

• Exten si ve on-l in e help

The MPLAB IDE allows you to:

• Edit your source files (eithe r asse mbly or C)

• One touch assemble (or compile) and download

to PICmicro emulator and simulator tools

(automatically updates all project information)

• Debug us ing :

- source files (as sembl y or C)

- mixed assembly and C

- machine code

MPLAB IDE supports multiple debugging tools in a

single development paradigm, from the cost effective

simulators, through low-cost in-circuit debuggers, to

full-featured emulators. This eliminates the learning

curve whe n upgrading to tools with increasin g flexibi lity

and power.

21.2 MPASM Assembler

The MPASM assembler is a full-featured, universal

macro assembler for all PICmicro MCUs.

The MPASM assembler generates relocatable object

files for the MPLINK object linker, Intel® standard HEX

files, M AP files to detail memory u sage and symbol re f-

erence, a bsolute LST files that cont ain source lines and

generated machine code and COFF files for

debugging.

The MPASM assembler features include:

• Integration into MPLAB IDE projects

• User de fined m acros to strea mline assemb ly cod e

• Condit ion al as sem bl y for multi-purpose sourc e

files

• Directives that allow complete control over the

assembly process

PIC18F1220/1320

21.3 MPLAB C17 and MPLAB C18

C Compilers

The MPLAB C17 and MPLAB C18 Code Development

Systems are complete ANSI C compilers for

Microchip’s PIC17CXXX and PIC18CXXX family of

microcontrollers. These compilers provide powerful

integration capabilities, superior code optimization and

ease of use not found with other compilers.

For easy source level debugging, the compilers provide

symbol info rmation tha t is optimized to the MPLAB IDE

debugger.

21.4 MPLINK Object Linker/

MPLIB Object Librari an

The MPLINK object linker combines relocatable

objects created by the MPASM assembler and the

MPLAB C17 and MPLAB C18 C compilers. It can link

relocatable objects from precompiled libraries, using

directives from a linker script.

The MPLIB object librarian manages the creation and

modification of library files of precompiled code. When

a routine from a library is called from a source file , only

the modules that contain that routine will be linked in

with the application. This allows large libraries to be

used efficiently in many different applications.

The object linker/library features include:

• Efficient linking of single libraries instead of many

smaller files

• Enhanced code maintainability by grouping

related modules together

• Flexible creation of libraries with easy module

listing, replacement, de letion and extraction

21.5 MPLAB C30 C Compiler

The MPLAB C30 C compiler is a full-featured, ANSI

compliant, optimizing compiler that translates standard

ANSI C programs into dsPIC30F assembly language

source. The compiler also supports many command

line options and language extensions to take full

adv antage of the dsPIC 30F dev ice ha rdwar e capab ili-

ties and afford fine control of the compiler code

generator.

MPLAB C30 is distributed with a complete ANSI C

standard library. All library functions have been vali-

dated an d c on form to the ANSI C li brary standard. Th e

library includes functions for string manipulation,

dynamic memory allocation, data conversion, time-

keepin g and math func tions (trigonome tric, expone ntial

and hyperbolic). The compiler provides symbolic

information for high-level source debugging with the

MPLAB IDE.

21.6 MPLAB ASM30 Assembler, Linker

and Librarian

MPLAB ASM30 assembler produces relocatable

machine code from symbolic assembly language for

dsPIC30F devices. MPLAB C30 compiler uses the

assembler to produce it’s object file. The assembler

generates relocatable object files that can then be

archived or linke d with other relocatable ob ject files and

arch ives to c rea te an e xecu tabl e fil e. N otabl e fe atu res

of the assembler include:

• Support for the entire dsPIC30F instruction set

• Support for fixed-point and floating-point data

• Command line interface

• Rich dire cti ve set

• Flexible macro language

• MPLAB IDE compatibility

21.7 MPLAB SIM Software Simulator

The MPLAB SIM sof tware simulat or allows code deve l-

opment in a PC hosted environment by simulating the

PICmicro series microcontrollers on an instruction

level. On any given instruction, the data areas can be

examined or modified and stimuli can be applied from

a file, or use r de fined key p ress, to any pin. The exec u-

tion can be performed in Single-Step, Execute Until

Break or Trace mode.

The MPLAB SIM simulator fully supports symbolic

debugging using the MPLAB C17 and MPLAB C18

C Compilers, as well as the MPASM assembler. The

software simulator offers the flexibility to develop and

debug code outside of the laboratory environment,

making it an excellent, economical software

development tool.

21.8 MPLAB SIM30 Software Simulator

The MPLAB SIM30 software simulator allows code

develop ment in a PC hosted en vironment by simulating

the dsPIC30F series microcontrollers on an instruct ion

level. On any given instruction, the data areas can be

examined or modified and stimuli can be applied from

a file, or user defined key press, to any of the pins.

The MPLAB SIM30 simulator fully supports symbolic

debugging using the MPLAB C30 C Compiler and

MPLAB ASM30 assembler . The simulator runs in either

a Command Line mode for automated tasks, or from

MPLAB IDE. This high-speed simulator is designed to

debug, analyze and optimize time intensive DSP

routines.

PIC18F1220/1320

21.9 MPLAB ICE 2000

High-Performance Universal

In-Circui t Emu lator

The MPLAB ICE 2000 universal in-circuit emulator is

intended to provide the product development engineer

with a complete microcontroller design tool set for

PICmicro microcontrollers. Software control of the

MPLAB ICE 2000 in-circuit emulator is advanced by

the MPLAB Integrated Development Environment,

which all ows ed iting, b uildin g, do wnlo ading and sourc e

debuggi ng from a singl e envi ronm en t.

The MPLAB ICE 2000 is a full-featured emulator sys-

tem with enhanced trace, trigger and data monitoring

featur es. Interchangea ble processo r modules al low the

system to be easi ly reconfi gured for emula tion of d iffer-

ent processors. The universal architecture of the

MPLAB ICE in-circuit emulator allows expansion to

support new PICmicro microcontrollers.

The MPLAB ICE 2000 in-circuit emulator system has

been designed as a real-time emulation system with

advanced features that are typically found on more

expensive development tools. The PC platform and

Microsoft® Windows 32-bit operating system were

chosen to best make these features available in a

simple, unified application.

21.10 MPLAB ICE 4000

High-Performance Universal

In-Circui t Emu lator

The MPLAB ICE 4000 universal in-circuit emulator is

intended to provide the product development engineer

with a co mplete micro controller de sign tool se t for high-

end PICmicro microcontrollers. Software control of the

MPLAB ICE in-circuit emulator is provided by the

MPLAB Integrated Development Environment, which

allows editing, building, downloading and source

debuggi ng from a singl e envi ronm en t.

The MPLAB ICD 4000 is a premium emulator system,

providing the features of MPLAB ICE 2000, but with

increased emulation memory and high-speed perfor-

mance for dsPIC30F and PIC18XXXX devices. Its

advanc ed emulator fe atures inc lude complex t riggering

and timing, up to 2 Mb of emulation memory and the

ability to view variables in real-time.

The MPLAB ICE 4000 in-circuit emulator system has

been designed as a real-time emulation system with

advanced features that are typically found on more

expensive development tools. The PC platform and

Microsoft Windows 32-bit operating system were

chosen to best make these features available in a

simple, unified application.

21.11 MPLAB ICD 2 In-Circuit Debugger

Microchip’s In-Circuit Debugger, MPLAB ICD 2, is a

powerful, low-cost, run-time development tool,

connecting to the host PC via an RS-232 or high-speed

USB interface. This tool is based on the Flash

PICmicro MCUs and can be used to develop for these

and other PICmicro microcontrollers. The MPLAB

ICD 2 utilizes the in-circuit debugging capability built

into the Flash devices. This feature, along with

Microchip’s In-Circuit Serial ProgrammingTM (ICSPTM)

protocol , offe rs cost ef fective i n-circuit Flash debug ging

from the graphical user interface of the MPLAB

Integrated Development Environment. This enables a

designer to develop and debug source code by setting

breakpoints, single-stepping and watching variables,

CPU status and peripheral registers. Running at full

speed enables testing hardware and applications in

real-tim e. MPLAB ICD 2 also serves as a de velop ment

programmer for selected PICmicro devices.

21.12 PRO MATE II Universal Device

Programmer

The PRO MATE II is a universal, CE compliant device

programmer with programmable voltage verification at

VDDMIN and VDDMAX for maxi mum reli abili ty. It feature s

an LCD display for instructions and error messages

and a modular detachable socket assembly to support

various package types. In Stand-Alone mode, the

PRO MATE II device programmer can read, verify and

program PICmicro devices without a PC connection. It

can also set code protection in this mode.

21.13 MPLAB PM3 Device Programmer

The MPLAB PM3 is a universal, CE compliant device

programmer with programmable voltage verification at

VDDMIN and VDDMAX for maxi mum reli abili ty. It feature s

a large LCD display (128 x 64) for menus and error

messages and a modular detachable socket assembly

to support various package types. The ICSP™ cable

assembly is included as a standard item. In Stand-

Alone mode , the M PLAB PM3 devi ce pr ogra mmer ca n

read, verify and program PICmicro devices without a

PC connection. It can also set code protection in this

mode. M PLAB PM3 con nects t o the host PC via an RS-

232 or USB cable. MPLAB PM3 has high-speed com-

munications and optimized algorithms for quick pro-

gramming of large memory devices and incorporates

an SD/ MMC card fo r file s torage an d secure d ata a ppli-

cations.

PIC18F1220/1320

21.14 PICSTART Plus Development

Programmer

The PICSTART Plus development programmer is an

easy-to-use, low-cost, prototype programmer. It con-

nects to the PC via a COM (RS-232) port. MPLAB

Inte grated Dev elopmen t En vironme nt so ftware makes

using the programmer simple and efficient. The

PICSTART Plus development programmer supports

most PICmicro devices up to 40 pins. Larger pin count

devices, such as the PIC16C92X and PIC17C76X,

may be supported with an adapter socket. The

PICSTART Plus development programmer is CE

compliant.

21.15 PICDEM 1 PICmicro

Demonstration Board

The PICDEM 1 demo nstrat ion boa rd demo nstrate s the

capabilities of the PIC16C5X (PIC16C54 to

PIC16C58A), PIC16C61, PIC16C62X, PIC16C71,

PIC16C8X, PIC17C42, PIC17C43 and PIC17C44. All

necessary hardware and software is included to run

basic demo programs. The sample microcontrollers

provi d ed wi t h the P IC DE M 1 de mo ns t rat i on b oar d c an

be pro gramme d with a PRO MATE II de vice pr ogram-

mer or a PICSTART Plus development programmer.

The PICDE M 1 demonstrati on board can be conne cted

to the MPLAB ICE in-circuit emulator for testing. A

proto type area extends the ci rcuitry for a dditio nal appli-

cation components. Features include an RS-232

interface, a potentiometer for simulated analog input,

push button switches and eight LEDs.

21.16 PICDEM.net Internet/E thernet

Demonstration Board

The PICDEM.net demonstration board is an Internet/

Ethernet demonstration board using the PIC18F452

microcontroller and TCP/IP firmware. The board

supports any 40-pin DIP device that conforms to the

standard pinout used by the PIC16F877 or

PIC18C452. This kit features a user friendly TCP/IP

stack, web server with HTML, a 24L256 Serial

EEPROM for Xmodem download to web pages into

Serial EEPROM, ICSP/MPLAB ICD 2 interface con-

nector, an Ethernet interface, RS-232 interface and a

16 x 2 LCD display. Also included is the book and

CD-ROM “TCP/IP Lean, Web Servers for Embedded

Systems,” by Jeremy Bentham

21.17 PICDEM 2 Plus

Demonstration Board

The PICDEM 2 Plus demonstration board supports

many 18, 28 and 40-pin microcontrollers, including

PIC16F87X and PIC18FXX2 devices. All the neces-

sary ha rdware and s oftware is included to run the dem-

onstration programs. The sample microcontrollers

provided with the PICDEM 2 demonstration board can

be programmed with a PRO MATE II device program-

mer, PICSTART Plus development programmer, or

MPLAB ICD 2 with a Universal Programmer Adapter.

The MPLAB I CD 2 and MPLAB ICE in-circuit emul ators

may also be used with the PICDEM 2 demonstration

board to test firmware. A prototype area extends the

circuitry for additional application components. Some

of the features include an RS-232 interface, a 2 x 16

LCD display , a piezo speaker , an on-board temperature

sensor, four LEDs and sample PIC18F452 and

PIC16F877 Flash microcontrollers.

21.18 PICDEM 3 PIC16C92X

Demonstration Board

The PICDEM 3 demonstration board supports the

PIC16C923 and PIC16C924 in the PLCC package. All

the necessary hardware and software is included to run

the demonstration programs.

21.19 PICDEM 4 8/14/18-Pin

Demonstration Board

The PICDEM 4 can be used to demonstrate the capa-

bilities of the 8, 14 and 18-pin PIC16XXXX and

PIC18XXXX MCUs, including the PIC16F818/819,

PIC16F87/88, PIC16F62XA and the PIC18F1320

family of microcontrollers. PICDEM 4 is intended to

showcase the many features of these low pin count

parts, including LIN and Motor Control using ECCP.

Special provisions are made for low-power operation

with the supercapacitor circuit and jumpers allow on-

board hardware to be disabled to eliminate current

draw in this mode. Included on the demo bo ard are pro-

visions for Crystal, RC or Canned Oscillator modes, a

five volt regulator for use with a nine volt wall adapter

or battery, DB-9 RS-232 interface, ICD connector for

programming via ICSP and development with MPLAB

ICD 2, 2 x 16 liqui d crystal dis play, PCB footpri nts for

H-Bridge motor driver, LIN transceiver and EEPROM.

Also in clude d are: head er for expansi on, eig ht L EDs,

four potentiometers, three push buttons and a proto-

typi ng are a. Incl uded wit h the ki t is a P IC16F62 7A and

a PIC18F1320. Tutorial firmware is included along

with th e User’s Guide.

PIC18F1220/1320

21.20 PICDEM 17 Demonstration Board

The PICDEM 17 demonstration board is an evaluation

board that demonstrates the capabilities of several

Microchip microcontrollers, including PIC17C752,

PIC17C756A, PIC17C762 and PIC17C766. A pro-

gramme d sample i s included. The PR O MA TE I I device

programmer, or the PICSTART Plus development pro-

gramme r , can be used to reprogram the device for user

tailored application development. The PICDEM 17

demonstration board supports program download and

execution from external on-board Flash memory. A

generous proto typ e area is av ailab le for user hardw are

expansion.

21.21 PICDEM 18R PIC18C601/801

Demonstration Board

The PICDEM 18R demonstration board serves to assist

development of the PIC18C601/801 family of Microchip

microcontrollers. It provides hardware implementation

of both 8-bit Multiplexed/Demultiplexed and 16-bit

Memory modes. The board includes 2 Mb external

Flash memory and 128 Kb SRAM memory, as well as

serial EEPROM, allowing access to the wide range of

memory types supported by the PIC18C601/801.

21.22 PICDEM LIN PIC16C43X

Demonstration Board

The pow erfu l LI N hard w are a nd s of tw are kit includes a

series of boards and three PICmicro microcontrollers.

The small footprint PIC16C432 and PIC16C433 are

used as slaves in the LIN communication and feature

on-board LIN transceivers. A PIC16F874 Flash

microcontroller serves as the master. All three micro-

controllers are programmed with firmware to provide

LIN b us communication.

21.23 PICkitTM 1 Flash Starter Kit

A complete “developmen t system in a box”, the PICkit™

Flash Starter Kit includes a convenient multi-section

board for programming, evaluation and development of

8/14-pin Flash PIC® microc ontrollers. Powered via USB,

the board operates under a simple Windows GUI. The

PICkit 1 Starter Kit includes the User’s Guide (on CD

ROM), PICkit 1 tutorial software and code for various

applications. Also included are MPLAB® IDE (Integrated

Development Environment) software, software and

hardware “Tips 'n Tricks for 8-pin Flash PIC®

Microcontrollers” Handbook and a USB interface cable.

Supports all current 8/14-pin Flash PIC microc ontrollers,

as well as many future planned dev ices .

21.24 PICDEM USB PIC16C7X5

Demonstration Board

The PICDEM U SB Demo ns trati on Board sho w s o f f th e

capabilities of the PIC16C745 and PIC16C765 USB

microcontrollers. This board provides the basis for

future USB products.

21.25 Evaluation and

Programming Tools

In additio n to the PICDEM seri es of circuits, Microchip

has a line of evaluation kits and demonstration software

for the se products.

•K

EELOQ evaluation and prog ram mi ng too ls for

Microchip’s HCS Secure Data Products

• CAN developers kit for automotive network

applications

• Analog design boards and filter design software

• PowerSmart battery charging evaluation/

calibration kits

•IrDA

® development kit

• microID development and rfLabTM development

software

• SEEVAL® designer k it f or m em ory ev al uation and

endurance calculations

• PICDEM MSC demo boards for Switching mode

power supply, high-power IR driver, delta sigma

ADC and flow rate sensor

Check the Microchip web page and the latest Product

Selector Guide for the complete list of demonstration

and evaluation kits.

PIC18F1220/1320

NOTES:

PIC18F1220/1320

22.0 ELECTRICAL CHARACTERISTICS

Absolute Maximum Ratings(†)

Ambient temperature under bias.............................................................................................................-40°C to +125°C

Storage temperature.............................................................................................................................. -65°C to +150°C

Voltage on any pin with respect to VSS (except VDD, MCLR and RA4)..........................................-0.3V to (VDD + 0.3V)

Vo lt a ge on VDD with respect to VSS ......................................................................................................... -0.3V to +5.5V

Vo lt a ge on MCLR with respect to VSS (Note 2)......................................................................................... 0V to +13.25V

Voltage on RA4 with respect to Vss............................................................................................................... 0V to +8.5V

Total power diss ipation (Note 1) ...............................................................................................................................1.0W

Maximum curr ent o ut of VSS pin ...........................................................................................................................300 mA

Maximum curr ent i nto VDD pin..............................................................................................................................250 mA

Input clamp current, IIK (VI < 0 or VI > VDD)...................................................................................................................... ±20 mA

Output clamp current, IOK (VO < 0 or VO > VDD).............................................................................................................. ±20 mA

Maximum output current sunk by any I/O pin..........................................................................................................25 mA

Maximum output current sourced by any I/O pin....................................................................................................25 mA

Maximum curr ent su nk by all ports .......................................................................................................................200mA

Maximum current sourced by all ports..................................................................................................................200 mA

Note 1: Power dissipation is calcu lated as follows:

Pdis = VDD x {IDD – ∑ IOH} + ∑ {(VDD – VOH) x IOH} + ∑(VOL x IOL)

2: V o ltage sp ikes below VSS at the MCLR/VPP pin, induc ing c urrent s g reater than 8 0 mA , ma y ca use l atch-u p.

Thus, a se ries resisto r of 50-100Ω should be u sed w he n a ppl yi ng a “low” level to the MC L R/VPP pin, rath er

than pulling this pin directly to VSS.

† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the

device. This is a stress rating only and functional operation of the device at those or any other conditions above those

indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for

extended periods may affect device reliability.

PIC18F1220/1320

FIGURE 22-1: PIC18F1220/1320 VOLTAGE-FREQUE NCY GRAPH (INDUSTRIAL)

FIGURE 22-2: PIC18LF1220/1320 VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL)

Frequency

Voltage

6.0V

5.5V

4.5V

4.0V

2.0V

40 MHz

5.0V

3.5V

3.0V

2.5V

PIC18F1X20

4.2V

Frequency

Voltage

6.0V

5.5V

4.5V

4.0V

2.0V

40 MHz

5.0V

3.5V

3.0V

2.5V

FMAX = (16.36 MHz/V) (VDDAPPMIN – 2.0V ) + 4 MHz

Note: VDDAPPMIN is the minimum voltage of the PICmicro® de vi ce in the app lic ation.

4 MHz

4.2V

PIC18LF1X20

PIC18F1220/1320

FIGURE 22-3: PIC18F1220/1320 VOLTAGE-FREQUENCY GRAPH (EXTENDED)

Frequency

Voltage

6.0V

5.5V

4.5V

4.0V

2.0V

25 MHz

5.0V

3.5V

3.0V

2.5V

PIC18F1X20-E

4.2V

PIC18F1220/1320

22.1 DC Characteristics: Supply Voltage

PIC18F1220/1320 (I ndustrial)

PIC18LF1220/1320 (I ndustrial)

PIC18LF1220/1320

(Industrial) Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Symbol Characteristic Min Typ Max Units Conditions

VDD Supply Vol tage

D001 PIC18LF1220/1320 2.0 — 5.5 V HS, XT, RC and LP Oscillator mode

PIC18F1220/1320 4.2 —5.5 V

D002 VDR RAM Dat a Retention

Voltage(1) 1.5 — — V

D003 VPOR VDD Start Voltage to ensure

internal Power-on Reset signal — — 0.7 V See Section 4.1 “Power-on Reset (POR)”

for details.

D004 SVDD VDD Rise Rate to ensure

internal Power-on Reset signal 0.05 — — V /m s See Section 4.1 “Power-on Reset (POR)”

for details.

VBOR Brown-out Reset Vol tage

D005D PIC18LF1220/1320 Industrial Low Voltage (-10°C to +85°C)

BORV1:BORV0 = 11 N/A N/A N/A V Reserved

BORV1:BORV0 = 10 2.50 2.72 2.94 V

BORV1:BORV0 = 01 3.88 4.22 4.56 V (Note 2)

BORV1:BORV0 = 00 4.18 4.54 4.90 V (Note 2)

D005F PIC18LF1220/1320 Industrial Low Voltage (-40°C to -10°C)

BORV1:BORV0 = 11 N/A N/A N/A V Reserved

BORV1:BORV0 = 10 2.34 2.72 3.10 V

BORV1:BORV0 = 01 3.63 4.22 4.81 V (Note 2)

BORV1:BORV0 = 00 3.90 4.54 5.18 V (Note 2)

D005G PIC18F1220/1320 Industrial (-10°C to +85°C)

BORV1:BORV0 = 1x N/A N/A N/A VReserved

BORV1:BORV0 = 01 3.88 4.22 4.56 V(Note 2)

BORV1:BORV0 = 00 4.18 4.54 4.90 V(Note 2)

D005H PIC18F1220/1320 Industrial (-40°C to -10°C)

BORV1:BORV0 = 1x N/A N/A N/A VReserved

BORV1:BORV0 = 01 N/A N/A N/A VReserved

BORV1:BORV0 = 00 3.90 4.54 5.18 V(Note 2)

D005J PIC18F1220/1320 Extended (-10°C to +85°C)

BORV1:BORV0 = 1x N/A N/A N/A VReserved

BORV1:BORV0 = 01 3.88 4.22 4.56 V(Note 3)

BORV1:BORV0 = 00 4.18 4.54 4.90 V(Note 3)

D005K PIC18F1220/1320 Extended (-40°C to -10°C, +85°C to +125°C)

BORV1:BORV0 = 1x N/A N/A N/A VReserved

BORV1:BORV0 = 01 N/A N/A N/A VReserved

BORV1:BORV0 = 00 3.90 4.54 5.18 V(Note 3)

Legend: Shading of rows is to assist in readability of the table.

Note 1: This is the limit to which VDD can be lowered in Sleep mode, or during a device Reset, without losing RAM data.

2: When BOR is on and BORV<1:0> = 0x, the device will operate correctly at 40 MHz for any VDD at which the BOR allows

execution (low-voltage and industrial devices only).

3: When BOR is on and BORV<1:0> = 0x, the device will operate correctly at 25 MHz for any VDD at which the BOR allows

execution (extended devices only).

PIC18F1220/1320

22.2 DC Characteristics: Power-Down and Supply Current

PIC18F1220/1320 (I ndustrial)

PIC18LF1220/1320 (I ndustrial)

PIC18LF1220/1320

(Industrial) Standard Operating Condit ions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Device Typ Max Units Conditions

Power-Down Current (IPD)(1)

PIC18LF1220/1320 0.1 0.5 μA -40°C VDD = 2.0V,

(Sleep mode)

0.1 0.5 μA +25°C

0.2 1.9 μA +85°C

PIC18LF1220/1320 0.1 0.5 μA -40°C VDD = 3.0V,

(Sleep mode)

0.1 0.5 μA + 25°C

0.3 1.9 μA +85°C

All devices 0.1 2.0 μA -40°C

VDD = 5.0V,

(Sleep mode)

0.1 2.0 μA +25°C

0.4 6.5 μA +85°C

Extended devices 11.2 50 μA +125°C

Supply Current (IDD)(2,3)

PIC18LF1220/1320 8 40 μA -40°C

FOSC = 31 kHz

(RC_RUN mode,

Internal oscillator source)

940μA+25°C V

DD = 2.0V

11 40 μA+85°C

PIC18LF1220/1320 25 68 μA -40°C

25 68 μA+25°C V

DD = 3.0V

20 68 μA+85°C

All devices 55 80 μA -40°C

VDD = 5.0V

55 80 μA+25°C

50 80 μA+85°C

Extended devices 50 80 μA +125°C

Legend: Shading of rows is to assist in readability of the table.

Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedanc e state and tied to VDD or VSS and all features that add delta

current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading

and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on

the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated

by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.

4: S tandard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature

crystals are available at a much higher cost.

PIC18F1220/1320

Supply Current (IDD)(2,3)

PIC18LF1220/1320 140 220 μA -40°C

FOSC = 1 MHz

(RC_RUN mode,

Internal oscillator source)

145 220 μA+25°C V

DD = 2.0V

155 220 μA+85°C

PIC18LF1220/1320 215 330 μA -40°C

225 330 μA+25°C V

DD = 3.0V

235 330 μA+85°C

All devices 385 550 μA -40°C

VDD = 5.0V

390 550 μA+25°C

405 550 μA+85°C

Extended devices 410 6 50 μA +125°C

PIC18LF1220/1320 410 600 μA -40°C

FOSC = 4 MHz

(RC_RUN mode,

Internal oscillator source)

425 600 μA+25°C V

DD = 2.0V

435 600 μA+85°C

PIC18LF1220/1320 650 900 μA -40°C

670 900 μA+25°C V

DD = 3.0V

680 900 μA+85°C

All devices 1.2 1.8 mA -40°C

VDD = 5.0V

1.2 1.8 mA +25°C

1.2 1.8 mA +85°C

Extended devices 1.2 1.8 mA +125°C

22.2 DC Characteristics: Power-Down and Supply Current

PIC18F1220/1320 (I ndustrial)

PIC18LF1220/1320 (Industrial) (Conti nued)

PIC18LF1220/1320

(Industrial) Standard Operating Condit ions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Device Typ Max Units Conditions

Legend: Shading of rows is to assist in readability of the table.

Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedanc e state and tied to VDD or VSS and all features that add delta

current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading

and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on

the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated

by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.

4: S tandard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperat ure

crystals are available at a much higher cost.

PIC18F1220/1320

Supply Current (IDD)(2,3)

PIC18LF1220/1320 4.7 8 μA -40°C

FOSC = 31 kHz

(RC_IDLE mode,

Internal oscillator source)

5.0 8 μA+25°C V

DD = 2.0V

5.8 11 μA+85°C

PIC18LF1220/1320 7.0 11 μA -40°C

7.8 11 μA+25°C V

DD = 3.0V

8.7 15 μA+85°C

All devices 12 16 μA -40°C

VDD = 5.0V

14 16 μA+25°C

14 22 μA+85°C

Extended devices 25 75 μA +125°C

PIC18LF1220/1320 75 150 μA -40°C

FOSC = 1 MHz

(RC_IDLE mode,

Internal oscillator source)

85 150 μA+25°C V

DD = 2.0V

95 150 μA+85°C

PIC18LF1220/1320 110 180 μA -40°C

125 180 μA+25°C V

DD = 3.0V

135 180 μA+85°C

All devices 180 380 μA -40°C

VDD = 5.0V

195 380 μA+25°C

200 380 μA+85°C

Extended devices 350 4 35 μA +125°C

22.2 DC Characteristics: Power-Down and Supply Current

PIC18F1220/1320 (I ndustrial)

PIC18LF1220/1320 (I ndustrial) (Continued)

PIC18LF1220/1320

(Industrial) Standard Operating Condit ions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Device Typ Max Units Conditions

Legend: Shading of rows is to assist in readability of the table.

Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedanc e state and tied to VDD or VSS and all features that add delta

current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading

and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on

the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated

by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.

4: S tandard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature

crystals are available at a much higher cost.

PIC18F1220/1320

Supply Current (IDD)(2,3)

PIC18LF1220/1320 140 275 μA -40°C

FOSC = 4 MHz

(RC_IDLE mode,

Internal oscillator source)

140 275 μA+25°C V

DD = 2.0V

150 275 μA+85°C

PIC18LF1220/1320 220 375 μA -40°C

220 375 μA+25°C V

DD = 3.0V

220 375 μA+85°C

All devices 390 800 μA -40°C

VDD = 5.0V

400 800 μA+25°C

380 800 μA+85°C

Extended devices 410 8 00 μA +125°C

PIC18LF1220/1320 150 250 μA -40°C

FOSC = 1 M HZ

(PRI_RUN mode,

EC oscillator)

150 250 μA+25°C V

DD = 2.0V

160 250 μA+85°C

PIC18LF1220/1320 340 350 μA -40°C

300 350 μA+25°C V

DD = 3.0V

280 350 μA+85°C

All devices 0.72 1.0 mA -40°C

VDD = 5.0V

0.63 1.0 mA +25°C

0.58 1.0 mA +85°C

Extended devices 0.53 1.0 mA +125°C

22.2 DC Characteristics: Power-Down and Supply Current

PIC18F1220/1320 (I ndustrial)

PIC18LF1220/1320 (Industrial) (Conti nued)

PIC18LF1220/1320

(Industrial) Standard Operating Condit ions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Device Typ Max Units Conditions

Legend: Shading of rows is to assist in readability of the table.

Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedanc e state and tied to VDD or VSS and all features that add delta

current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading

and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on

the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated

by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.

4: S tandard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperat ure

crystals are available at a much higher cost.

PIC18F1220/1320

Supply Current (IDD)(2,3)

PIC18LF1220/1320 415 600 μA -40°C

FOSC = 4 MHz

(PRI_RUN mode,

EC oscillator)

425 600 μA+25°C V

DD = 2.0V

435 600 μA+85°C

PIC18LF1220/1320 0.87 1.0 mA -40°C

0.75 1.0 mA +25°C VDD = 3.0V

0.75 1.0 mA +85°C

All devices 1.6 2.0 mA -40°C

VDD = 5.0V

1.6 2.0 mA +25°C

1.5 2.0 mA +85°C

Extended devices 1.5 2.0 mA +125°C

Extended devices 6.3 9.0 mA +125°C VDD = 4.2V FOSC = 25 MHz

(PRI_RUN mode,

EC oscillator)

9.7 10.0 mA +125°C VDD = 5.0V

All devices 9.4 12 mA -40°C

FOSC = 40 MHZ

(PRI_RUN mode,

EC oscillator)

9.5 12 mA +25°C VDD = 4.2V

9.6 12 mA +85°C

All devices 11.9 15 mA -40°C VDD = 5.0V12.1 15 mA +25°C

12.2 15 mA +85°C

22.2 DC Characteristics: Power-Down and Supply Current

PIC18F1220/1320 (I ndustrial)

PIC18LF1220/1320 (I ndustrial) (Continued)

PIC18LF1220/1320

(Industrial) Standard Operating Condit ions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Device Typ Max Units Conditions

Legend: Shading of rows is to assist in readability of the table.

Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedanc e state and tied to VDD or VSS and all features that add delta

current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading

and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on

the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated

by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.

4: S tandard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature

crystals are available at a much higher cost.

PIC18F1220/1320

Supply Current (IDD)(2,3)

PIC18LF1220/1320 35 50 μA -40°C

FOSC = 1 MHz

(PRI_IDLE mode,

EC oscillator)

35 50 μA+25°C V

DD = 2.0V

35 60 μA+85°C

PIC18LF1220/1320 55 80 μA -40°C

50 80 μA+25°C V

DD = 3.0V

60 100 μA+85°C

All devices 105 150 μA -40°C

VDD = 5.0V

110 150 μA+25°C

115 150 μA+85°C

Extended devices 125 3 00 μA +125°C

PIC18LF1220/1320 135 180 μA -40°C

FOSC = 4 MHz

(PRI_IDLE mode,

EC oscillator)

140 180 μA+25°C V

DD = 2.0V

140 180 μA+85°C

PIC18LF1220/1320 215 280 μA -40°C

225 280 μA+25°C V

DD = 3.0V

230 280 μA+85°C

All devices 410 525 μA -40°C

VDD = 5.0V

420 525 μA+25°C

430 525 μA+85°C

Extended devices 450 8 00 μA +125°C

Extended devices 2.2 3.0 mA +125°C VDD = 4.2V FOSC = 25 MHz

(PRI_IDLE mode,

EC oscillator)

2.7 3.5 mA +125°C VDD = 5.0V

22.2 DC Characteristics: Power-Down and Supply Current

PIC18F1220/1320 (I ndustrial)

PIC18LF1220/1320 (Industrial) (Conti nued)

PIC18LF1220/1320

(Industrial) Standard Operating Condit ions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Device Typ Max Units Conditions

Legend: Shading of rows is to assist in readability of the table.

Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedanc e state and tied to VDD or VSS and all features that add delta

current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading

and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on

the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated

by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.

4: S tandard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperat ure

crystals are available at a much higher cost.

PIC18F1220/1320

Supply Current (IDD)(2,3)

All devices 3.2 4.1 mA -40°C

FOSC = 40 MHz

(PRI_IDLE mode,

EC oscillator)

3.2 4.1 mA +25°C VDD = 4.2 V

3.3 4.1 mA +85°C

All devices 4.0 5.1 mA -40°C VDD = 5.0V4.1 5.1 mA +25°C

4.1 5.1 mA +85°C

PIC18LF1220/1320 5.1 9 μA -10°C

FOSC = 32 kHz (4)

(SEC_RUN mode,

Timer1 as clock)

5.8 9 μA+25°C V

DD = 2.0V

7.9 11 μA+70°C

PIC18LF1220/1320 7.9 12 μA -10°C

8.9 12 μA+25°C V

DD = 3.0V

10.5 14 μA+70°C

All devices 12.5 20 μA -10°C VDD = 5.0V16.3 20 μA+25°C

18.4 25 μA+70°C

22.2 DC Characteristics: Power-Down and Supply Current

PIC18F1220/1320 (I ndustrial)

PIC18LF1220/1320 (I ndustrial) (Continued)

PIC18LF1220/1320

(Industrial) Standard Operating Condit ions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Device Typ Max Units Conditions

Legend: Shading of rows is to assist in readability of the table.

Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedanc e state and tied to VDD or VSS and all features that add delta

current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading

and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on

the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated

by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.

4: S tandard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature

crystals are available at a much higher cost.

PIC18F1220/1320

Supply Current (IDD)(2,3)

PIC18LF1220/1320 9.2 15 μA -10°C

FOSC = 32 kHz (4)

(SEC_IDLE mode,

Timer1 as clock)

9.6 15 μA+25°C V

DD = 2.0V

12.7 18 μA+70°C

PIC18LF1220/1320 22 30 μA -10°C

21 30 μA+25°C V

DD = 3.0V

20 35 μA+70°C

All devices 50 80 μA -10°C VDD = 5.0V45 80 μA+25°C

45 80 μA+70°C

22.2 DC Characteristics: Power-Down and Supply Current

PIC18F1220/1320 (I ndustrial)

PIC18LF1220/1320 (Industrial) (Conti nued)

PIC18LF1220/1320

(Industrial) Standard Operating Condit ions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Device Typ Max Units Conditions

Legend: Shading of rows is to assist in readability of the table.

Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedanc e state and tied to VDD or VSS and all features that add delta

current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading

and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on

the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated

by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.

4: S tandard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperat ure

crystals are available at a much higher cost.

PIC18F1220/1320

Module Differential Currents (ΔIWDT, ΔIBOR, ΔILVD, ΔIOSCB, ΔIAD)

D022

(ΔIWDT)Watchdog Timer 1.5 4.0 μA -40°C

2.2 4.0 μA+25°C V

DD = 2.0V

3.1 5.0 μA+85°C

2.5 6.0 μA -40°C

3.3 6.0 μA+25°C V

DD = 3.0V

4.7 7.0 μA+85°C

3.7 10.0 μA -40°C

4.5 10.0 μA+25°C V

DD = 5.0V

6.1 13.0 μA+85°C

D022A

(ΔIBOR)Brown-out Reset 19 35.0 μA-40°C to +85°CV

DD = 3.0V

24 45.0 μA-40°C to +85°CV

DD = 5.0V

D022B

(ΔILVD)Low-Voltage Detect 8.5 25.0 μA-40°C to +85°CV

DD = 2.0V

16 35.0 μA-40°C to +85°CV

DD = 3.0V

20 45.0 μA-40°C to +85°CV

DD = 5.0V

D025

(ΔIOSCB)Timer1 Oscillator 1.7 3.5 μA-40°C

1.8 3.5 μA+25°CV

DD = 2.0V 32 kHz on Timer1(4)

2.1 4.5 μA+85°C

2.2 4.5 μA-40°C

2.6 4.5 μA+25°CV

DD = 3.0V 32 kHz on Timer1(4)

2.8 5.5 μA+85°C

3.0 6.0 μA-40°C

3.3 6.0 μA+25°CV

DD = 5.0V 32 kHz on Timer1(4)

3.6 7.0 μA+85°C

D026

(ΔIAD)A/D Converter 1.0 3.0 μA-40°C to +85°CV

DD = 2.0V

A/D on, not converting

1.0 4.0 μA-40°C to +85°CV

DD = 3.0V

2.0 10.0 μA-40°C to +85°CV

DD = 5.0V

1.0 8.0 μA-40°C to +125°CV

DD = 5.0V

22.2 DC Characteristics: Power-Down and Supply Current

PIC18F1220/1320 (I ndustrial)

PIC18LF1220/1320 (I ndustrial) (Continued)

PIC18LF1220/1320

(Industrial) Standard Operating Condit ions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Device Typ Max Units Conditions

Legend: Shading of rows is to assist in readability of the table.

Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedanc e state and tied to VDD or VSS and all features that add delta

current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading

and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on

the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated

by the formula Ir = VDD/2REXT (mA) with REXT in kΩ.

4: S tandard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature

crystals are available at a much higher cost.

PIC18F1220/1320

22.3 DC Characteristics: PIC18F1220/1320 (Industria l)

PIC18LF1220/1320 (I ndustrial)

DC CHARACTERISTICS Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for indu strial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Symbol Characteristic Min Max Units Conditions

VIL Input Low Voltage

I/O ports:

D030 with TTL buffer VSS 0.15 VDD VVDD < 4.5V

D030A — 0.8 V 4.5V ≤ VDD ≤ 5.5V

D031 with Schmitt Trigger buffer VSS 0.2 VDD V

D032 MCLR VSS 0.2 VDD V

D032A OSC1 (in XT , HS and LP modes)

and T1OSI VSS 0.3 VDD V

D033 OSC1 (in RC and EC mode)(1) VSS 0.2 VDD V

VIH Input High Voltage

I/O ports:

D040 with TTL buffer 0.25 VDD + 0.8V VDD VVDD < 4.5V

D040A 2.0 VDD V4.5V ≤ VDD ≤ 5.5V

D041 with Schmitt Trigger buffer 0.8 VDD VDD V

D042 MCLR, OSC1 (EC mode) 0.8 VDD VDD V

D042A OSC1 (in XT, HS and LP modes)

and T1OSI 1.6 VDD VDD V

D043 OSC1 (RC mode)(1) 0.9 VDD VDD V

IIL Input Leakage Current(2,3)

D060 I/O ports — ±1μAVSS ≤ VPIN ≤ VDD,

Pin at high-impedance

D061 MCLR —±5μAVSS ≤ VPIN ≤ VDD

D063 OSC1 — ±5μAVSS ≤ VPIN ≤ VDD

IPU Weak Pull- up C urrent

D070 IPURB PORTB weak pull-up current 50 400 μAVDD = 5V, VPIN = VSS

Note 1: In RC oscillator con figuration , the OSC1/CL KI pin is a Schmitt T r igger inpu t. It is not recomm ended that the

PICmicro® device be driven with an external clock while in RC mode.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified

levels represent normal operating conditions. Higher leakage current may be measured at different input

voltages.

3: Negative current is defined as current sourced by the pin.

4: Parameter is characterized but not tested.

PIC18F1220/1320

VOL Output Low Voltage

D080 I/O ports — 0.6 V IOL = 8.5 mA, VDD = 4.5V,

-40°C to +85°C

D083 OSC2/CLKO

(RC mode) —0.6VI

OL = 1.6 mA, VDD = 4.5V,

-40°C to +85°C

VOH Output High Voltage(3)

D090 I/O ports VDD – 0.7 — V IOH = -3.0 mA, VDD = 4.5V ,

-40°C to +85°C

D092 OSC2/CLKO

(RC mode) VDD – 0.7 — V IOH = -1.3 mA, VDD = 4.5V,

-40°C to +85°C

D150 VOD Open-Drain High Volt a ge —8.5VRA4 pin

Capacitive Loading Specs

on Output Pins

D100(4) COSC2 OSC2 pin —15 pF In XT, HS and LP modes

when external clock is

used to drive OSC1

D101 CIO All I/O pins and OSC2

(in RC mode) — 50 pF To meet the AC timing

specifications

D102 CBSCL, SDA — 400 pF In I2C mode

22.3 DC Characteristics: PIC18F1220/1320 (Industria l)

PIC18LF1220/1320 (I ndustrial) (Continued)

DC CHARACTERISTICS Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Symbol Characteristic Min Max Units Conditions

Note 1: In RC oscillator con figuration , the OSC1/CL KI pin is a Schmitt Trigger input. It is not recommend ed that the

PICmicro® device be driven with an external clock while in RC mode.

2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified

levels represent normal operating conditions. Higher leakage current may be measured at different input

voltages.

3: Negative current is defined as current sourced by the pin.

4: Parameter is characterized but not tested.

PIC18F1220/1320

TABLE 22-1: MEMORY PROGRAMMING REQUIREMENTS

DC CHARACTERISTICS Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

Param

No. Sym Characteristic Min Typ† Max Units Conditions

Internal Program Memory

Programming Specifications(1)

D110 VPP Voltage on MCLR/VPP pin 9.00 — 13.25 V (Note 2)

D112 IPP Current into MCLR/VPP pin — — 5 μA

D113 IDDP Supply Current during

Programming ——10mA

Data EEPROM Memory

D120 EDByte Endurance 100K 1M — E/W -40°C to +85°C

D121 VDRW VDD for Read/Write VMIN — 5.5 V Using EECON to read/write

VMIN = Minimum operating

voltage

D122 TDEW Erase/Write Cycle Time — 4 — ms

D123 TRETD Characteristic Retention 40 — — Year Provided no other

specifications are violated

D124 TREF Nu mber of Total Eras e/Writ e

Cycles before Re fresh(3) 1M 10M — E/W -40°C to +85°C

Program Flash Memory

D130 EPCell Endurance 10K 100K — E/W -40°C to +85°C

D131 VPR VDD for Read VMIN —5.5VVMIN = Minimum operating

voltage

D132 VIE VDD for Block Erase 4.5 — 5.5 V Using ICSP port

D132A VIW VDD for Externally Timed Erase

or Write 4.5 — 5.5 V Using ICSP port

D132B VPEW VDD for Self-Timed Write VMIN —5.5VVMIN = Minimum operating

voltage

D133 TIE ICSP™ Block Erase Cycle Time — 4 — ms VDD > 4.5V

D133A TIW ICSP E rase or Write Cycle Time

(externall y tim ed) 1——msVDD > 4.5V

D133A TIW Self-Timed Write Cycle Time — 2 — ms

D134 TRETD Characteristic Retention 40 — — Year Provided no other

specifications are violated

† Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance

only and are not tested .

Note 1: These specifications are for programming the on-chip program memory through the use of table write

instructions.

2: The pin may be kept in this range at times other than programming, but it is not recommended.

3: Refer to Section 7.8 “Using the Data EEPROM” for a more detailed discussion on data EEPROM

endurance.

PIC18F1220/1320

FIGURE 22-4: LOW-VOLTAGE DETECT CHARACTERISTICS

VLVD

LVDIF

VDD

(LVDIF set by hardware)

(LVDIF can be

cleared in software)

TABLE 22-2: LOW-VOLTAGE DETECT CHARACTERISTICS

PIC18LF1220/1320

(Industrial) Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Symbol Characteristic Min Typ† Max Units Conditions

D420D LVD Voltage on VDD Transition High-to-Low Industrial Low Voltage (-10°C to +85°C)

PIC18LF1220/1320 LVDL<3:0> = 0000 N/A N/A N/A V Reserved

LVD L<3:0> = 0001 N/A N/A N/A V Reserved

LVD L<3:0> = 0010 2.08 2.26 2.44 V

LVD L<3:0> = 0011 2.26 2.45 2.65 V

LVD L<3:0> = 0100 2.35 2.55 2.76 V

LVD L<3:0> = 0101 2.55 2.77 2.99 V

LVD L<3:0> = 0110 2.64 2.87 3.10 V

LVD L<3:0> = 0111 2.82 3.07 3.31 V

LVD L<3:0> = 1000 3.09 3.36 3.63 V

LVD L<3:0> = 1001 3.29 3.57 3.86 V

LVD L<3:0> = 1010 3.38 3.67 3.96 V

LVD L<3:0> = 1011 3.56 3.87 4.18 V

LVD L<3:0> = 1100 3.75 4.07 4.40 V

LVD L<3:0> = 1101 3.93 4.28 4.62 V

LVD L<3:0> = 1110 4.23 4.60 4.96 V

Legend: Shading of rows is to assist in readability of the table.

† Production tested at TAMB = 25°C. Specifications over temperature limits ensured by characterization.

PIC18F1220/1320

D420F LVD Voltage on VDD Transition High-to-Low Industrial Low Voltage (-40°C to -10°C)

PIC18LF1220/1320 LVDL<3:0> = 0000 N/A N/A N/A V Reserved

LVDL<3:0> = 0001 N/A N/A N/A V Reserved

LVDL<3:0> = 0010 1.99 2.26 2.53 V

LVDL<3:0> = 0011 2.16 2.45 2.75 V

LVDL<3:0> = 0100 2.25 2.55 2.86 V

LVDL<3:0> = 0101 2.43 2.77 3.10 V

LVDL<3:0> = 0110 2.53 2.87 3.21 V

LVDL<3:0> = 0111 2.70 3.07 3.43 V

LVDL<3:0> = 1000 2.96 3.36 3.77 V

LVDL<3:0> = 1001 3.14 3.57 4.00 V

LVDL<3:0> = 1010 3.23 3.67 4.11 V

LVDL<3:0> = 1011 3.41 3.87 4.34 V

LVDL<3:0> = 1100 3.58 4.07 4.56 V

LVDL<3:0> = 1101 3.76 4.28 4.79 V

LVDL<3:0> = 1110 4.04 4.60 5.15 V

LVD Voltage on VDD Transition High-to-Low Industrial (-10°C to +85°C)

D420G PIC18F1220/1320 LVDL<3:0> = 1101 3.93 4.28 4.62 V

LVDL<3:0> = 1110 4.23 4.60 4.96 V

LVD Voltage on VDD Transition High-to-Low Industrial (-40°C to -10°C)

D420H PIC18F1220/1320 LVDL<3:0> = 1101 3.76 4.28 4.79 V

LVDL<3:0> = 1110 4.04 4.60 5.15 V

LVD Voltage on VDD Transition High-to-Low Extended (-10°C to +85°C)

D420J PIC18F1220/1320 LVDL<3:0> = 1101 3.94 4.28 4.62 V

LVDL<3:0> = 1110 4.23 4.60 4.96 V

LVD Voltage on VDD Transition High-to-Low Extended (-40°C to -10°C, +85°C to +125°C)

D420K PIC18F1220/1320 LVDL<3:0> = 1101 3.77 4.28 4.79 V

LVDL<3:0> = 1110 4.05 4.60 5.15 V

TABLE 22-2: LOW-VOLTAGE DETECT CHARACTERISTICS (CONTINUED)

PIC18LF1220/1320

(Industrial) Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Symbol Characteristic Min Typ† Max Units Conditions

Legend: Shading of rows is to assist in readability of the table.

† Production tested at TAMB = 25°C. Specifications over temperature limits ensured by characterization.

PIC18F1220/1320

22.4 AC (Timing) Characteristics

22.4.1 TIMING PARAMETER SYMBOLOGY

The timing parameter symbols have been created

following one of the following formats:

1. TppS2ppS 3. TCC:ST (I2C specifications only)

2. TppS 4. Ts (I2C specifications only)

TF Frequency T Time

Lowercase letters (pp) and their meanings:

pp cc CCP1 osc OSC1

ck CLKO rd RD

cs CS rw RD or WR

di SDI sc SCK

do SDO ss SS

dt Data in t0 T0CKI

io I/O port t1 T13CKI

mc MCLR wr WR

Uppe rcase letters and th eir meanings:

SF Fall P Period

HHigh RRise

I Invalid (High-Impedance) V Valid

L Low Z High-Impedance

I2C only

AA ou tput access High High

BUF Bus free Low Low

TCC:ST (I2C specifications only)

CC HD Hold SU Setup

ST DAT DATA input hold STO Stop condition

STA Start condition

PIC18F1220/1320

22.4.2 TIMING CONDITIONS

The temperature and voltages specified in Table 22-3

apply to all timing specifications unless otherwise

noted. Figure 22-5 specifies the load conditions for the

timing specificati o n s.

TABLE 22-3: TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC

FIGURE 22-5: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS

AC CHARACTERISTICS

S tandard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85° C for industrial

-40°C ≤ TA ≤ +125°C for extended

Operating voltage VDD range as described in DC spec Section 22.1 and

Section 22.3.

LF parts operate for industrial temperatures only.

VDD/2

VSS

RL= 464Ω

CL= 50 pF for all pi ns except OSC2/CLKO

Load Condition 1 Load Condition 2

PIC18F1220/1320

22.4.3 TIMING DIAGRAMS AND SPECIFICATIONS

FIGURE 22-6: EXTERNAL CLOCK TIMING (ALL MODES EXCEPT PLL)

TABLE 22-4: EXTERNAL CLOCK TIMING REQUIREMENTS

OSC1

CLKO

Q4 Q1 Q2 Q3 Q4 Q1

23344

Param.

No. Symbol Characteristic Min Max Units Conditions

1A FOSC External CLKI Frequenc y(1) DC 40 MHz EC, ECIO (LF and Industrial)

DC 25 MHz EC, ECIO (Extended)

Oscillator Frequency(1) DC 4 MHz RC oscillator

DC 1 MHz XT oscillator

DC 25 MHz HS oscillator

1 10 MHz HS + PLL oscillator

DC 33 kHz LP Oscillator mode

OSC External CLKI Period (1) 25 — ns EC, ECIO (LF and Industrial)

40 — ns EC, ECIO (Exte nd ed)

Oscillator Period(1) 250 — ns RC oscillator

1000 — ns XT oscillator

100 —

1000 ns

ns HS oscillator

HS + PLL oscillator

30 — μs LP oscillator

2TCY Instruction Cycle Time(1) 100 — ns TCY = 4/FOSC

3 TosL,

TosH External Clock in (OSC1)

High or Low Time 30 — ns XT oscillator

2.5 — μs LP oscillator

10 — ns HS oscillator

4TosR,

TosF External Clock in (OSC1)

Rise or Fall Time — 20 ns XT oscillator

— 50 ns LP oscillator

— 7.5 ns HS oscillator

Note 1: Instruction cy cle period (TCY) equals four times the input oscillator time base period for all configurations

except PLL . Al l specified va lue s are bas ed on char ac teri zat ion dat a for that particular osci ll ator type under

sta ndard ope rating conditi ons, with the devic e exec uting co de. Exce eding these sp ecifie d limits may res ult

in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested

to operate at “min.” values with an external clock applied to the OSC1/CLKI pin. When an external clock

input is used, the “max.” cycle time limit is “DC” (no clock) for all devices.

PIC18F1220/1320

TABLE 22-5: PLL CLOCK TIMING SPECIFICATIONS, HS/HSPLL MODE (VDD = 4.2V TO 5.5V)

Param

No. Sym Characteristic Min Typ† Max Units Conditions

F10 FOSC Oscilla tor Frequency Range 4 — 10 MHz HS and HSPLL mod e only

F11 FSYS On-Chip VCO System Frequency 16 — 40 MHz HSPLL mode only

F12 TPLL PLL Start-up Time (Lock Time) — — 2 ms HSPLL mode only

F13 ΔCLK CLKO Stability (Jitter) -2 — +2 % HSPLL mode only

† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance

only and are not tested .

TABLE 22-6: INTERNAL RC ACCURACY: PIC18F1220/1320 (INDUSTRIAL)

PIC18LF1220/1320 (INDUSTRIAL)

PIC18LF1220/1320

(Industrial) Standard Operating Conditions (unless otherwise stated)

Operating temperature - 40°C ≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial)

Standard Operating Conditions (unless otherwise stated)

Operating temperature -40°C ≤ TA ≤ +85°C for industrial

-40°C ≤ TA ≤ +125°C for extended

Param

No. Device Min Typ Max Units Conditions

INTOSC Accuracy @ Freq = 8 MHz, 4 MHz, 2 MHz, 1 MHz, 500 kHz, 250 kHz, 125 kHz(1)

PIC18LF1220/1320 -2 +/-1 2 % +25°C VDD = 2.7-3.3V

-5 — 5 % -10°C to +85°C VDD = 2.7-3.3V

-10 — 10 % -40°C to +85°C V DD = 2.7-3.3V

PIC18F1220/1320PIC18F

1220/1320 -2 +/-1 2 % +25°C VDD = 4.5-5.5V

-5 — 5 % -10°C to +85°C VDD = 4.5-5.5V

-10 —10 %-40°C to +85°C VDD = 4.5-5.5V

INTRC Accuracy @ Freq = 31 kHz(2)

PIC18LF1220/1320 26.562 — 35.938 kHz -40°C to +85°C V DD = 2.7-3.3V

PIC18F1220/1320PIC18F

1220/1320 26.562 —35.938 kHz -40°C to +85°C VDD = 4.5-5.5V

Legend: Shading of rows is to assist in readability of the table.

Note 1: Frequency calibrated at 25°C. OSCTUNE register can be used to compensate for temperature and VDD drift.

2: INTRC frequency after calibration.

3: Change of INTRC frequency as VDD changes.

PIC18F1220/1320

FIGURE 22-7: CLKO AND I/O TIMING

TABLE 22-7: CLKO AND I/O TI MING REQUIREMENTS

Note: Refer to Figure 22-5 for load conditions.

OSC1

CLKO

I/O pin

(Input)

I/O pin

(Output)

Q4 Q1 Q2 Q3

13 14

20, 21

19 18

Old Value New Value

Param.

No. Symbol Characteristic Min Typ Max Units Conditions

10 TosH2ckL OSC1↑ to CLKO↓ — 75 200 ns (Note 1)

11 TosH2ckH OSC1↑ to CLKO↑ — 75 200 ns (Note 1)

12 TckR CLKO Rise Time — 35 100 ns (Note 1)

13 TckF CLKO Fall Time — 35 100 ns (Note 1)

14 TckL2ioV CLKO↓ to Port Out Valid — — 0.5 TCY + 20 ns (Note 1)

15 TioV2ckH Port In Valid before CLKO↑ 0.25 TCY + 25 — — ns (Note 1)

16 TckH2ioI Port In Hold after CLKO↑ 0——ns(Note 1)

17 TosH2ioV OSC1↑ (Q1 cycle) to Port Out Valid — 50 150 ns

18 TosH2ioI OSC1↑ (Q2 cycle) to Port

Input Invalid (I/O in hold time) PIC18F1X20 100 — — ns

18A PIC18LF1X20 200 — — ns

19 TioV2osH Port Input Valid to OSC1↑

(I/O in setup time) 0——ns

20 TioR Port Output Rise Time PIC18F1X20 — 10 25 ns

20A PIC18LF1X20 — — 60 ns

21 TioF Port Outp ut Fa ll Time PIC18F1X20 — 10 25 ns

21A PIC18LF1X20 — — 60 ns

Note 1: Measurements are taken in RC mode, where CLKO output is 4 x TOSC.

PIC18F1220/1320

FIGURE 22-8: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND

POWER-UP TIMER TIMING

FIGURE 22-9: BROWN-OUT RESET TIMING

VDD

MCLR

Internal

POR

PWRT

Time-out

OSC

Time-out

Internal

Reset

Watchdog

Timer

Reset

I/O pi n s

Note: Refer to Figure 22-5 for load conditions.

VDD BVDD

35 VBGAP = 1.2V

VIRVST

Enable Internal

Internal Reference 36

Reference Voltage

Voltage Stable

PIC18F1220/1320

TABLE 22-8: RESET, WATCHDOG TIMER, OS CILLATOR START-UP TIMER, POWER-UP TIMER

AND BROWN-OUT RESET REQUIREMENTS

FIGURE 22-10: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS

Param.

No. Symbol Characteristic Min Typ Max Units Conditions

30 TmcL MCLR Pulse Width (low) 2 — — μs

31 TWDT Watchdog Timer Time-out Period

(No postscaler) 3.48 4.00 4.71 ms

32 TOST Oscillation Start-up Timer Period 1024 TOSC — 1024 TOSC —TOSC = OSC1 period

33 TPWRT Power-up Timer Period — 65.5 132 ms

34 TIOZ I/O High-Impedance from MCLR

Low or Watchdog Timer Reset —2—μs

35 TBOR Brown-out Reset Pulse Width 200 — — μsVDD ≤ BVDD (see D005)

36 TIVRST Time for Internal Reference

Voltage to become stable —2050 μs

37 TLVD Low-Voltage Detect Pulse Width 200 — — μsVDD ≤ VLVD

Note: Refer to Figure 22-5 for load conditions.

T0CKI

T1OSO/T13CKI

TMR0 or

TMR1

PIC18F1220/1320

TABLE 22-9: T IMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS

FIGURE 22-11: CAPTURE/COMPARE/PWM TIMINGS (ALL CCP MODULES)

Param

No. Symbol Characteristic Min Max Units Conditions

40 Tt0H T0CKI High Pulse Width No prescaler 0.5 TCY + 20 — ns

With presca ler 10 — ns

41 Tt0L T0CKI Low Pulse Width No prescaler 0.5 TCY + 20 — ns

With presca ler 10 — ns

42 Tt0P T0CKI Period No prescaler TCY + 10 — ns

With prescaler Greater of:

20 ns or TCY + 40

—nsN = prescale

value

(1, 2, 4,..., 256)

45 Tt1H T1 3CKI H ig h Tim e Synchronou s, no presc ale r 0.5 TCY + 20 — ns

Synchronous,

with presca ler PIC18F1X20 10 — ns

PIC18LF1X20 25 — ns

Asynchronous PIC18F1X20 30 — ns

PIC18LF1X20 50 — ns

46 Tt1L T13C KI Lo w Time Synchronous, no presc ale r 0.5 TCY + 5 — ns

Synchronous,

with presca ler PIC18F1X20 10 — ns

PIC18LF1X20 25 — ns

Asynchronous PIC18F1X20 30 — ns

PIC18LF1X20 50 — ns

47 Tt1P T13CKI Input

Period Synchronous Greater of:

20 ns or TCY + 40

—nsN = prescale

value

(1, 2, 4, 8)

Asynchronous 60 — ns

Ft1 T13CKI Oscillator Input Frequency Range DC 50 kHz

48 Tcke2 t mr I D ela y from Externa l T13CKI Clock Edge to

Timer Increment 2 TOSC 7 TOSC —

Note: Refer to Figure 22-5 for load conditions.

CCPx

(Capture Mode)

50 51

CCPx

53 54

(Compare or PWM Mode)

PIC18F1220/1320

TABLE 22-10: CAPTURE/COMPARE/PWM REQUIREMENTS (ALL CCP MODULES)

FIGURE 22-12: EUSART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING

TABLE 22-11: EUSART SYNCHRONOUS TRANSMISSION REQUIREMENTS

Param.

No. Symbol Characteristic Min Max Units Conditions

50 TccL CCPx In put Low

Time No prescaler 0.5 TCY + 20 — ns

With prescaler PIC18F1X20 10 — ns

PIC18LF1X20 20 — ns

51 TccH CCPx Input High

Time No prescaler 0.5 TCY + 20 — ns

With prescaler PIC18F1X20 10 — ns

PIC18LF1X20 20 — ns

52 TccP CCPx Input Period 3 TCY + 40

N— ns N = prescale

value (1, 4 or 16)

53 TccR CCPx Output Fall Time PIC18F1X20 — 25 ns

PIC18LF1X20 — 45 ns

54 TccF CCPx Output Fall Time PIC18F1X20 — 25 ns

PIC18LF1X20 — 45 ns

121 121

120 122

RB1/AN5/TX/

RB4/AN6/RX/

DT/KBI0 pin

CK/INT1 pin

Note: Refer to Figure 22-5 for load conditions.

Param.

No. Symbol Characteristic Min Max Units Conditions

120 TckH2dtV SYNC XMIT (MASTER & SLAVE)

Clock High to Data Out Valid PIC18F1X20 — 40 ns

PIC18LF1X20 — 100 ns

121 Tckrf Clock Out Rise Time and Fall Time

(Master mode) PIC18F1X20 — 20 ns

PIC18LF1X20 — 50 ns

122 Tdtrf Data Out Rise Time and Fall Time PIC18F1X20 — 20 ns

PIC18LF1X20 — 50 ns

PIC18F1220/1320

FIGURE 22-13: EUSART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING

TABLE 22-12: EUSART SYNCHRONOUS RECEIVE REQUIREMENTS

TABLE 22-13: A/D CONVERTER CHARACTERISTICS: PIC18F1220/1320 (INDUSTRIAL)

PIC18LF1220/1320 (INDUSTRIAL)

Param.

No. Symbol Characteristic Min Max Units Conditions

125 TdtV2ckl SYNC RCV (MASTER & SLAVE)

Data Hold before CK↓ (DT hold time) 10 — ns

126 TckL2dtl Data Hold after CK↓ (DT hold time) 15 — ns

Param

No. Symbol Characteristic Min Typ Max Units Conditions

A01 NRResolution — — 10 bit ΔVREF ≥ 3.0V

A03 EIL Integr al Lin ear ity Error — — <±1 LSb ΔVREF ≥ 3.0V

A04 EDL Differential Linearity Error — — <±1 LSb ΔVREF ≥ 3.0V

A06 EOFF Offset Error — — <±1 LSb ΔVREF ≥ 3.0V

A07 EGN Gain Error — — <±1 LSb ΔVREF ≥ 3.0V

A10 — Monotonicity guaranteed(2) —

A20 ΔVREF Reference Voltage Range

(VREFH – VREFL)3—AV

DD – AVSS V For 10-bit resolution

A21 VREFH Reference Voltage High AVSS + 3.0V — AVDD + 0.3V V For 10-bit resolution

A22 VREFL Reference Voltage Lo w AVSS – 0.3V — AVDD – 3.0V V For 10-bit r esolution

A25 VAIN Analog Input Voltage VREFL —VREFH V

A28 AVDD Analog Supply Voltage VDD – 0.3 — VDD + 0.3 V

A29 AVSS Analog Supply Voltage VSS – 0.3 — VSS + 0.3 V

A30 ZAIN Recomm end ed Impedance of

Analog Voltage Source ——2.5kΩ

A40 IAD A/D Convers ion

Current (VDD)PIC18F1X20 — 180 — μA Average current

cons umption when

A/D is on (Note 1)

PIC18LF1X20 — 90 — μA

A50 IREF VREF Input Current (Note 3) —

——

—±5

±150 μA

μADuring VAIN acquisition.

During A/D conversion

cycle.

Note 1: When A/D is off, it will not consume any current other than minor leakage current. The power-down current

specification includes any such leakage from the A/D module.

2: The A/D co nve rsion result n ever de creas es wi th an in creas e in the input v olt ag e an d has n o miss ing c odes.

3: VREFH current is from RA3/AN3/VREF+ pin or AVDD, whichever is selected as the VREFH source.

VREFL current is from RA2/AN2/VREF- pin or AVSS, whichever is selected as the VREFL source.

125

126

Note: Refer to Figure 22-5 for load conditions.

RB1/AN5/TX/

RB4/AN6/RX/

DT/KBI0 pin

CK/INT1 pin

PIC18F1220/1320

FIGURE 22-14: A/D CONVERSION TIMING

TABLE 22-14: A/D CONVERSION REQUIREMENTS

131

130

132

BSF ADCON0, GO

A/D CLK(1)

A/D DATA

ADRES

ADIF

SAMPLE

OLD_DATA

Sampling Stopped

DONE

NEW_DATA

(Note 2)

987 21 0

Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts.

This allows the SLEEP instruction to be executed.

2: This is a minimal RC delay (typically 100 ns), which also disconnects the holding capacitor from the analog input.

. . . . . .

TCY

Param

No. Symbol Characteristic Min Max Units Conditions

130 TAD A/D Clock Period PIC18F1X20 1.6 20(5) μsTOSC based, VREF ≥ 3.0V

PIC18LF1X20 3.0 20(5) μsTOSC based, VREF full range

PIC18F1X20 2.0 6.0 μs A/D RC mode

PIC18LF1X20 3.0 9.0 μs A/D RC mode

131 TCNV C onversion Time

(not including acquisition time) (Note 1) 11 12 TAD

132 TACQ Acquisition Time (Note 3) 15

10 —

—μs

μs-40°C ≤ Temp ≤ +125°C

0°C ≤ Temp ≤ +125°C

135 TSWC Switching Time from Convert → Sample — (Note 4)

136 TAMP Amplifier Settling Time (Note 2) 1—μs This may be used if the

“new” input voltage has not

changed by more tha n 1 LSb

(i.e., 5 mV @ 5.12 V) from the

last sampled voltage (as

stated on C HOLD).

Note 1: ADRES register may be read on the following TCY cycle.

2: See Section 17.0 “10-Bit Ana log-to-Digit al Converter (A/D) M odule” for minim um cond itions when input

voltage has changed more than 1 LSb.

3: The time for the holdi ng capacitor to ac quire the “New” input volt age, when the volt age changes full scale after

the conversion ( AVDD to AVSS, or AVSS to AVDD). The source impedance (RS) on the input channels is 50Ω.

4: On the next Q4 cycle of the device clock.

5: The time of the A/D clock period is dependent on the device frequency and the TAD clock divide r.

PIC18F1220/1320

NOTES:

PIC18F1220/1320

23.0 DC AND AC CHARACTERISTICS GRAPHS AND TABLES

“T ypical” represents the mean of the distribution at 25°C. “Maximum” or “minimum” represents (mean + 3σ) or (mean – 3σ)

respectively, where σ is a standa rd deviation, ov er the whol e temperature range .

FIGURE 23-1: TYPICAL IDD vs. FOSC OVER VDD PRI_RUN, EC MODE, +25°C

FIGURE 23-2: MAXIMUM IDD vs. FOSC OVER VDD PRI_RUN, EC MODE, -40°C TO +85°C

Note: The g r ap hs and t ables prov ide d followin g th is no te a r e a s t ati sti ca l s um ma ry based on a l im ite d n um ber of

samples and are provided for informational purposes only. The performance characteristics listed herein

are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified

operating range (e.g., outside specified power supply range) and therefore, outside the warranted range.

0.0

0.1

0.2

0.3

0.4

0.5

0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.20

FOSC (MHz)

IDD (mA)

5.0V

5.5V

4.0V

4.5V

3.0V

3.5V

2.0V

2.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.20

FOSC (MHz)

IDD (mA)

5.0V

5.5V

4.0V

4.5V

3.0V

3.5V

2.0V

2.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-3: MAXIMUM IDD vs. FOSC OVER VDD PRI_RUN, EC MODE, -40°C TO +125°C

FIGURE 23-4: TYPICAL IDD vs. FOSC OVER VDD PRI_RUN, EC MODE, +25°C

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.20

FOSC (MHz)

IDD (mA)

5.0V

5.5V

4.0V

4.5V

3.0V

3.5V

2.0V

2.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

0.0

0.2

0.4

0.6

0.8

1.0

1.2

1.4

1.6

1.8

2.0

1.0 1.5 2.0 2.5 3.0 3.5 4.0

FOSC (MHz)

IDD (mA)

5.0V

5.5V

4.0V

4.5V

3.0V

3.5V

2.0V

2.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-5: MAXIMUM IDD vs. FOSC OVER VDD PRI_RUN, EC MODE, -40°C TO +125°C

FIGURE 23-6: TYPICAL IDD vs. FOSC OVER VDD PRI_RUN, EC MODE, +25°C

0.0

0.5

1.0

1.5

2.0

2.5

1.0 1.5 2.0 2.5 3.0 3.5 4.0

FOSC (MHz)

IDD (mA)

5.0V

5.5V

4.0V

4.5V

3.0V

3.5V

2.0V

2.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

4 8 12 16 20 24 28 32 36 40

FOSC (MHz)

IDD (mA)

5.0V

5.5V

4.0V

4.5V

3.0V

3.5V

2.0V 2.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-7: MAXIMUM IDD vs. FOSC OVER VDD PRI_RUN, EC MODE, -40°C TO +125°C

FIGURE 23-8: TYPICAL IDD vs. FOSC OVER VDD PRI_IDLE, EC MODE, +25°C

4 8 12 16 20 24 28 32 36 40

FOSC (MHz)

IDD (mA)

5.0V

5.5V

4.0V

4.5V

3.0V

3.5V

2.0V 2.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

0.000

0.005

0.010

0.015

0.020

0.025

0.030

0.035

0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.20

FOSC (M Hz)

IDD (mA)

4.0V

4.5V

3.0V

3.5V

2.0V

2.5V

5.0V

5.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-9: MAXIMUM IDD vs. FOSC OVER VDD PRI_IDLE, EC MODE, -40°C TO +85°C

FIGURE 23-10 : MAXIMU M IDD vs. FOSC OVER VDD PRI_IDLE, EC MODE, -40°C TO +125°C

0.000

0.005

0.010

0.015

0.020

0.025

0.030

0.035

0.040

0.045

0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.20

FOSC (M Hz)

IDD (mA)

4.0V

4.5V

3.0V

3.5V

2.0V

2.5V

5.0V

5.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

0.000

0.010

0.020

0.030

0.040

0.050

0.060

0.070

0.080

0.090

0.100

0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.20

FOSC (MHz)

IDD (mA)

4.0V

4.5V

3.0V

3.5V

2.0V

2.5V

5.0V

5.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-11: TYPICAL IDD vs. FOSC OVER VDD PRI_IDLE, EC MODE, +25°C

FIGURE 23-12 : MAXIMU M IDD vs. FOSC OVER VDD PRI_IDLE, EC MODE, -40°C TO +125°C

Typical I vs F over V PRI_IDLE, EC mode, +25°C

100

200

300

400

500

600

1.0 1.5 2.0 2.5 3.0 3.5 4.0

FOSC (MHz)

IDD (μA)

4.0V

4.5V

3.0V

3.5V

2.0V

2.5V

5.0V

5.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

100

200

300

400

500

600

1.0 1.5 2.0 2.5 3.0 3.5 4.0

FOSC (MHz)

IDD (μA)

4.0V

4.5V

3.0V

3.5V

2.0V

2.5V

5.0V

5.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-13: TYPICAL IDD vs. FOSC OVER VDD PRI_IDLE, EC MODE, +25°C

FIGURE 23-14 : MAXIMU M IDD vs. FOSC OVER VDD PRI_IDLE, EC MODE, -40°C TO +125°C

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

5.5

6.0

4 8 12 16 20 24 28 32 36 40

FOSC (MHz)

IDD (mA)

4.0V

4.5V

3.0V

3.5V

2.0V

2.5V

5.0V

5.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

5.5

6.0

4 8 12 16 20 24 28 32 36 40

FOSC (MHz)

IDD (mA)

4.0V

4.5V

3.0V

3.5V

2.0V

2.5V

5.0V

5.5V

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-15: TYPICAL IPD vs. VDD (+25°C), 125 kHz TO 8 MHz RC_RUN MODE,

ALL PERIPHERALS DISABLED

FIGURE 23-16 : MAXIMU M IPD vs. VDD (-40°C TO +125°C), 125 kHz TO 8 MHz RC_RUN MODE,

ALL PERIPHERALS DISABLED

500

1000

1500

2000

2500

3000

2.02.53.03.54.04.55.05.5

VDD (V)

IPD (μA)

8 MHz

125 kHz

4 MHz

2 MHz

1 MHz

250 kHz and 500 kHz curves are

bounded by 125 k Hz and 1 MHz

curves.

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

500

1000

1500

2000

2500

3000

3500

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

IPD (μA)

8 MHz

125 kHz

4 MHz

2 MHz

1 MHz

250 kHz and 500 kHz curves are

bounded by 125 kH z and 1 MHz

curves.

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-17: TYPICAL AND MAXIMUM IPD vs. VDD (-40°C TO +125°C), 31.25 kHz RC_RUN MODE,

ALL PERIPHERALS DISABLED

FIGURE 23-18: TYPICAL IPD vs. VDD (+25°C), 125 kHz TO 8 MHz RC_IDLE MODE,

ALL PERIPHERALS DISABLED

100

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

IPD (μA)

Typ (+25°C)

Max (+85°C)

Max (+125°C)

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

100

150

200

250

300

350

400

450

500

550

600

650

700

750

800

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

IPD (μA)

8 MHz

125 kHz

4 MHz

2 MHz

1 MHz

250 kHz and 500 kHz curves are

bounded by 125 k H z and 1 MHz

curves.

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-19 : MAXIMU M IPD vs. VDD (-40°C TO +125°C), 125 kHz TO 8 MHz RC_IDLE MODE,

ALL PERIPHERALS DISABLED

FIGURE 23-20: TYPICAL AND MAX IMUM I PD vs. VDD (-40°C TO +12 5°C), 31 .2 5 kHz RC_I DLE MODE ,

ALL PERIPHERALS DISABLED

100

150

200

250

300

350

400

450

500

550

600

650

700

750

800

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

IPD (μA)

8 MHz

125 kHz

4 MHz

2 MHz

1 MHz

250 kHz and 500 kHz curves are

bounded by 125 kHz and 1 MHz

curves.

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

100

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

IPD (μA)

Typ (+25°C )

Max (+85°C)

Max ( +125°C)

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-21 : IPD SEC_RUN MODE, -10°C TO +70°C, 32.768 kHz XTAL , 2 x 22 pF,

ALL PERIPHERALS DISABLED

FIGURE 23-22 : IPD SEC_IDLE MODE, -10°C TO +70°C, 32.768 kHz, 2 x 22 pF,

ALL PERIPHERALS DISABLED

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

IPD (μA)

Typ (+25°C)

Max (+70°C)

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

IPD (μA)

Typ (+25°C)

Max (+70°C)

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-23 : TOTAL IPD, -40°C TO +125°C SLEEP MODE, ALL PERIPHERALS DISABLED

FIGURE 23-24 : VOH vs. IOH OVER TEMPERATURE (-40°C TO +125°C), VDD = 3.0V

0.001

0.01

0.1

100

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

IPD (μA)

Max (+85°C)

Max (+125°C)

Typ (+25°C)

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

0.0

0.5

1.0

1.5

2.0

2.5

3.0

0 5 10 15 20 25

IOH (-mA)

VOH (V)

Max (+125°C)

Min (+125°C)

Typ (+25°C)

PIC18F1220/1320

FIGURE 23-25 : VOH vs. IOH OVER TEMPERATURE (-40°C TO +125°C), VDD = 5.0V

FIGURE 23-26 : VOL vs. IOL OVER TEMPERATURE (-40°C TO +125°C), VDD = 3.0V

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

0 5 10 15 20 25

IOH (-mA)

VOH (V)

Max (+125°C)

Min (+125°C)

Typ (+25°C)

V vs I over Temp (-40°C to +125°C) V = 3.0V

0.0

0.5

1.0

1.5

2.0

2.5

3.0

0 5 10 15 20 25

IOL (-mA)

VOL (V)

Max (+125°C)

Max (+85°C)

Typ (+25°C)

Min (+125°C)

PIC18F1220/1320

FIGURE 23-27 : VOL vs. IOL OVER TEMPERATURE (-40°C TO +125°C), VDD = 5.0V

FIGURE 23-28 : ΔIPD TIMER1 OSCILLATOR, -10°C TO +70°C SLEEP MODE,

TMR1 COUNTER DISABLED

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

0 5 10 15 20 25

IOL (-mA)

VOL (V)

Max (+125°C)

Max (+85°C)

Typ (+25°C)

Min (+125°C)

IPD Timer1 Oscillator, -10°C to +70°C SLEEP mode, TMR1 counter disabled

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

2.02.53.03.54.04.55.05.5

VDD (V)

IPD (μA)

Typ (+25°C)

Max (- 10°C to +70°C)

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-29 : ΔIPD FSCM vs. VDD OVER TEMPERATURE PR I_ IDLE MODE ,

EC OSCILLATOR AT 32 kHz, -40°C TO +125°C

FIGURE 23-30 : ΔIPD WDT, -40°C TO +125°C SLEEP MODE, ALL PERIPHERALS DISABLED

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

ΔIPD (μA)

Typ (+25°C )

Max (-40°C)

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

ΔIPD (μA)

Typ (+2 5 °C)

Max (+85°C)

Max (+125°C)

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-31 : ΔIPD LVD vs. VDD SLEEP MODE, LVDL3:LVDL0 = 0001 (2V)

FIGURE 23-32 : ΔIPD BOR vs. VDD, -40°C TO +125°C SLEEP MODE,

BORV1:BORV0 = 11 (2V)

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

IPD (μA)

Typ (+25 °C)

Max (+85°C)

Max (+125°C)

Low-Voltage Detection Range

Normal Operating Range

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

2.02.53.03.54.04.55.05.5

VDD (V)

IPD (μA)

Max (+125°C)

Typ (+25°C)

Device may be in Res et

Device is Operating

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

PIC18F1220/1320

FIGURE 23-33 : ΔIPD A/D, -40°C TO +125°C SLEEP MODE, A/D ENABLED (NOT CONVERTING)

FIGURE 23-34: AVERAGE FOSC vs. VDD FOR VARIOUS R’s EXTERNAL RC MODE,

C = 20 pF, TEMPERATURE = +25°C

0.001

0.01

0.1

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

IPD (μA)

Max (+125°C)

Max (+85°C)

Typ (+25°C)

Typical: statistical mean @ 25°C

Maximum: mean + 3σ (-40°C to +125°C)

Minimum: mean – 3σ (-40°C to +125°C)

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

Freq (MH z)

5.1K

10K

33K

100K

Operation above 4 MHz is not recomended

PIC18F1220/1320

FIGURE 23-35: AVERAGE FOSC vs. VDD FOR VARIOUS R’s EXTERNAL RC MODE,

C = 100 pF, TEMPERATURE = +25°C

FIGURE 23-36: AVERAGE FOSC vs. VDD FOR VARIOUS R’s EXTERNAL RC MODE,

C = 300 pF, TEMPERATURE = +25°C

0.0

0.2

0.4

0.6

0.8

1.0

1.2

1.4

1.6

1.8

2.0

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

Freq (MH z)

5.1K

10K

33K

100K

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5

VDD (V)

Freq (MH z)

5.1K

10K

33K

100K

PIC18F1220/1320

24.0 PACKAGING INFORMATION

24.1 Package Marking Information

18-Lead PDIP

XXXXXXXXXXXXXXXXX

YYWWNNN

Example

PIC18F1320-I/P

0610017

18-Lead SOIC

XXXXXXXXXXXX

YYWWNNN

Example

PIC18F1220-

E/SO0610017

20-Lead SSOP

XXXXXXXXXXX

YYWWNNN

Example

PIC18F1220-

E/SS

0610017

28-Lead QFN

XXXXXXXX

YYWWNNN

Example

18F1320

-I/ML

0610017

Legend: XX...X Customer-specific information

Y Year code (last digit of calendar year)

YY Year code (last 2 digits of calendar year)

WW Week code (week of January 1 is week ‘01’)

NNN Alphanum eri c trac eab il ity code

Pb-free JEDEC designator for Matte Ti n (Sn)

*This packa ge is Pb-free. The Pb-free JEDEC designator ( )

can be found on the outer packaging for this package.

Note: In the event the fu ll Mic rochip part nu mber ca nnot be m arked on one line, it w ill

be carried over to the next line, thus limiting the number of available

characters for customer-specific information.

PIC18F1220/1320

24.2 Package Details

The following sections give the technical details of the

packages.

18-Lead Plastic Dual In-line (P) – 300 mil Body (PDIP)

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

1510515105

Mold Draft Angle Bottom 1510515105

Mold Draft Angle Top 10.929.407.87.430.370.310

Overall Row Spacing §0.560.460.36.022.018.014BLower Lead Width 1.781.461.14.070.058.045

Upper Lead Width 0.380.290.20.015.012.008

Lead Thickness 3.433.303.18.135.130.125LTip to Seating Plane 22.9922.8022.61.905.898.890DOverall Length 6.606.356.10.260.250.240E1Molded Pa ckag e Width 8.267.947.62.325.313.300EShoulder to Shoulder Width 0.38.015A1Base to Seating Plane 3.683.302.92.145.130.115A2Molded Packag e Thickness 4.323.943.56.170.155.140ATop to Seating Plane 2.54.100

Pitch 1818

Number of Pins MAXNOMMINMAXNOMMINDimension Limits MILLIMETERSINCHES*Units

* Controlling Parameter

Notes:

Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side.

JEDEC Equivalent: MS-001

Drawing No. C04-007

§ Significant Characteristic

PIC18F1220/1320

18-Lead Plasti c Small Outline (SO) – Wide, 300 mil Body (SOIC)

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Foot A ngle φ048048

1512015120

Mold Draft Angle Bottom 1512015120

Mold Draft Angle Top 0.510.420.36.020.017.014BLead Width 0.300.270.23.012.011.009

Lead Thickness

1.270.840.41.050.033.016LFoot Length 0.740.500.25.029.020.010hChamfer Distance 11.7311.5311.33.462.454.446DOverall Length 7.597.497.39.299.295.291E1Molded Packag e Width 10.6710.3410.01.420.407.394EOverall Width 0.300.200.10.012.008.004A1Standoff §2.392.312.24.094.091.088A2Molded Pa ckag e Thick ness 2.642.502.36.104.099.093AOverall Height 1.27

.050

Pitch 1818

Number of Pins MAXNOMMINMAXNOMMINDimension Limits MILLIMETERSINCHES*Units

45°

* Controlling Parameter

Notes:

Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 010” (0.254mm) per side.

JEDEC Equivalent: MS-013

Drawing No. C04-051

§ Significant Characteristic

PIC18F1220/1320

20-Lead Plasti c Shrink Small Outline (SS) – 209 mil Body, 5.30 mm (SSOP)

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

0.38-0.22.015-.009BLead Width

8°4°0°8°4°0°

Foot Angle

0.25-0.09.010-.004

Lead Thickness

0.950.750.55.037.030.022LFoot Length

7.507.206.90.295.283.272DOverall Length

5.385.255.11.212.207.201E1Molded Package Width

8.207.807.40.323.307.291EOverall Width

--0.05--.002A1Standoff

1.851.751.65.073.069.065A2Molded Package Thickness

2.00--.079--AOverall Height

0.65.026

Pitch

2020

Number of Pins

MAXNOMMINMAXNOMMINDimension Limits

MILLIMETERS*INCHESUnits

Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side.

Notes:

Drawing No. C04-072

*Controlling Parameter

Revised 7-20-06

LA1

PIC18F1220/1320

28-Lead Plasti c Quad Flat, No Lead Package (ML) - 6x6 mm Body [QFN]

With 0.55 mm Contact Length

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Number of Pins

Pitch

Overall Height

Standoff

Contact Thickness

Overall Width

Exposed Pad Width

Overall Length

Exposed Pad Length

Contact Width

Contact Length §

Contact-to-Exposed Pad §

Units

Dimension Limits

0.80

0.00

3.65

0.23

0.50

0.20

0.65 BSC

0.90

0.02

0.20 REF

6.00 BSC

3.70

6.00 BSC

3.70

0.30

0.55

—

1.00

0.05

4.20

0.35

0.70

—

MIN NOM MAX

MILLIMETERS

Notes:

1. Pin 1 visual index feature may vary, but must be located within the hatched area.

2. § Significant Characteristic

3. Package is saw singulated

4. Dimensioning and tolerancing per ASME Y14.5M

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

REF: Reference Dimension, usually without tolerance, for information purposes only.

Microchip Technology Drawing No. C04–105, Sept. 8, 2006

TOP VIEW

NOTE 1

BOTTOM VIEW

EXPOSED

PAD

PIC18F1220/1320

NOTES:

PIC18F1220/1320

APPENDIX A: REVISION HISTORY

Revision A (August 2002)

Original data sheet for PIC18F1220/1320 devices.

Revision B (November 2002)

This revision includes significant changes to

Section 2.0, Section 3.0 and Section 19.0, as wel l a s

updates to the El ectrical Specificati ons in Section 22.0

and includes minor corrections to the data sheet text.

Revision C (May 2004)

This rev is ion in cl ude s updates to the Elec tric al Spe ci fi-

cations in Section 22.0, the DC and AC Characteristics

Graphs and Tables in Section 23.0 and includes minor

corrections to the data sheet text.

Revision D (October 2006)

This revision includes updates to the packaging

diagrams.

APPENDIX B: DEVICE

DIFFERENCES

The differences between the devices listed in this data

sheet are shown in Table B-1.

TABLE B-1: DEVICE DIFFERENCES

Features PIC18F1220 PIC18F1320

Program Memo ry (Bytes ) 4096 8192

Program Memo ry (Instructions) 2048 4096

Interrupt Sources 15 15

I/O Ports Ports A, B Ports A, B

Enhanced Capture/Compare/PWM Modules 1 1

10-bit Analog-to-Digital Module 7 input channels 7 input channels

Packages

18-pin SDIP

18-pin SOIC

20-pin SSOP

28-pin QFN

18-pin SDIP

18-pin SOIC

20-pin S SOP

28-pin QFN

PIC18F1220/1320

APPENDIX C: CONVERSION

CONSIDERATIONS

This appendix discusses the considerations for con-

verting from previous versions of a device to the ones

listed in this data sheet. Typically, these changes are

due to the differences in the process technology used.

An example of this type of conversion is from a

PIC16C74A to a PIC16C74B.

Not Applicable

APPENDIX D: MIGRATION FROM

BASELINE TO

ENHANCED DEVICES

This section discusses how to migrate from a baseline

device (i.e., PIC16C5X) to an enhanced MCU device

(i.e., PIC18FXXX).

The following are the list of modifications over the

PIC16C5X mic roc on trol ler fam il y:

Not Currently Av ail able

PIC18F1220/1320

APPENDIX E: MIGRATION FROM

MID-RANGE TO

ENHANCED DEVICES

A detailed discussion of the differences between the

mid-range MCU devices (i.e., PIC16CXXX) and the

enhanced devices (i.e., PIC18FXXX) is provided in

AN716, “Migrating Designs from PIC16C74A/74B to

PIC18C442”. The changes discussed, while device

specific, are generally applicable to all mid-range to

enhanced device migrations.

This Ap plicatio n Note is availab le as L iterature Nu mber

DS00716.

APPENDIX F: MIGRATION FROM

HIGH-END TO

ENHANCED DEVICES

A detailed discussion of the migration pathway and

differences between the high-end MCU devices (i.e.,

PIC17CXXX) and the enhanced devices (i.e.,

PIC18FXXX) is provided in AN726, “PIC17CXXX to

PIC18CXXX Migration”.

This Ap plication Note is availab le as L iterature Nu mber

DS00726.

PIC18F1220/1320

NOTES:

© 2006 Microchip Technology Inc. DS39605D-page 297
PIC18F1220/1320
INDEX
A
A/D ...................................................................................155
A/D Converter Interrupt, Configuring .......................159
Acquisition Requirements ........................................160
ADCON0 Register ....................................................155
ADCON1 Register ....................................................155
ADCON2 Register ....................................................155
ADRESH Register ....................................................155
ADRESH/ADRESL Registers ..................................158
ADRESL Register ....................................................155
Analog Port Pins, Configuring ..................................162
Associated Registers ...............................................164
Configuring the Module ............................................159
Conversion Clock (Tad) ...........................................161
Conversion Requirements .......................................267
Conversion Status (GO/DONE Bit) ..........................158
Conversions .............................................................163
Converter Characteristics  ........................................266
Operation in Low-Power Modes ...............................162
Selecting, Configuring Automatic 
Acquisition Time ...............................................161
Special Event Trigger (CCP) ....................................117
Special Event Trigger (CCP1) ..................................164
Use of the CCP1 Trigger ..........................................164
VREF+ and VREF- References  ..................................160
Absolute Maximum Ratings  .............................................239
AC (Timing) Characteristics .............................................257
Conditions ................................................................258
Load Conditions for Device 
Timing Specifications .......................................258
Parameter Symbology .............................................257
Temperature and Voltage Specifications .................258
ADCON0 Register ............................................................155
GO/DONE Bit ...........................................................158
ADCON1 Register ............................................................155
ADCON2 Register ............................................................155
ADDLW ............................................................................197
ADDWF ............................................................................197
ADDWFC .........................................................................198
ADRESH Register ............................................................155
ADRESH/ADRESL Registers ...........................................158
ADRESL Register ............................................................155
Analog-to-Digital Converter. See A/D.
ANDLW ............................................................................198
ANDWF ............................................................................199
Assembler
MPASM Ass e mbler ..................................................233
Auto-Wake-up on Sync Break Character .........................145
B
BC ....................................................................................199
BCF ..................................................................................200
Block Diagrams
A/D ...........................................................................158
Analog Input Model ..................................................159
Capture Mode Operation .........................................117
Compare Mode Operation .......................................118
Enhanced PWM .......................................................120
EUSART Receive ....................................................143
EUSART Transmit ...................................................141
Fail-Safe Clock Monitor ............................................182
Generic I/O Port Operation ........................................87
Low-Voltage Detect (LVD) .......................................166
Low-Voltage Detect (LVD) with 
External Input .................................................. 166
MCLR/VPP/RA5 Pin ................................................... 89
On-Chip Reset Circuit ................................................ 33
OSC1/CLKI/RA7 Pin .................................................. 88
OSC2/CLKO/RA6 Pin ................................................ 88
PIC18F1220/1320 ....................................................... 7
PLL ............................................................................ 12
RA3:RA0 Pins ............................................................ 88
RA4/T0CKI Pin .......................................................... 88
RB0/AN4/INT0 Pin ..................................................... 90
RB1/AN 5/T X/ C K/ INT1 Pin ......................................... 91
RB2/P1B/INT2  Pi n ..................................................... 92
RB3/CCP1/P1A Pin ................................................... 93
RB4/AN 6/RX/DT/ KBI 0 Pin  ......................................... 94
RB5 /PGM/KB I1 Pin .................................................... 95
RB6/PGC/T1O SO/T13CK I/P1C/KBI2 Pin .................. 96
RB7/PGD/T1OSI /P 1D/KB I3 Pi n ................................. 97
Reads from Flash Program Memory .......................... 61
System Clock ............................................................. 16
Table Read Operation ............................................... 57
Table Write Operation ................................................ 58
Table Writes to Flash Program Memory .................... 63
Timer0 in 16-Bit Mode ............................................. 100
Timer0 in 8-Bit Mode ............................................... 100
Timer1 ..................................................................... 104
Timer1 (16-Bit Read/Write Mode) ............................ 104
Timer2 ..................................................................... 110
Timer3 ..................................................................... 112
Timer3 (16-bit Read/Write Mode) ............................ 112
WDT ........................................................................ 180
BN .................................................................................... 200
BNC ................................................................................. 201
BNN ................................................................................. 201
BNOV ............................................................................... 202
BNZ .................................................................................. 202
BOR. See Brown-out Reset.
BOV ................................................................................. 205
BRA ................................................................................. 203
Break Character (12-bit) Transmit and Receive .............. 146
Brown-out Reset (BOR) ..............................................34, 171
BSF .................................................................................. 203
BTFSC ............................................................................. 204
BTFSS ............................................................................. 204
BTG ................................................................................. 205
BZ .................................................................................... 206
C
C Compilers
MPLAB C17 ............................................................. 234
MPLAB C18 ............................................................. 234
MPLAB C30 ............................................................. 234
CALL ................................................................................ 206
Capture (CCP Module) .................................................... 116
CCP Pin Configuration ............................................. 116
CCPR1H:CCPR1L Registers ................................... 116
Softwar e  In terrupt .................................................... 116
Timer1/Timer3 Mode Selection ................................ 116
Capture, Compare, Timer1 and Timer3
Associated Registers ............................................... 118

PIC18F1220/1320
DS39605D-page 298 © 2006 Microchip Technology Inc.
Capture/Compare/PWM (CCP)
Capture Mode. See Capture.
CCP1 ........................................................................116
CCPR1H Register ............................................116
CCPR1L Register ............................................116
Compare Mode. See Compare.
Timer Resources ......................................................116
Clock Sources ....................................................................15
Selection Using OSCCON Register ...........................16
Clocking Scheme ...............................................................45
CLRF ................................................................................207
CLRWDT ..........................................................................207
Code Examples
16 x 16 Signed Multiply Routine .................................72
16 x 16 Unsigned Multiply Routine .............................72
8 x 8 Signed Multiply Routine .....................................71
8 x 8 Unsigned Multiply Routine .................................71
Changing Between Capture Prescalers ...................117
Computed GOTO Using an Offset Value ...................47
Data EEPROM Read .................................................69
Data EEPROM Refresh Routine ................................70
Data EEPROM Write ..................................................69
Erasing a Flash Program Memory Row .....................62
Fast Register Stack ....................................................44
How to Clear RAM (Bank 1) Using 
Indirect Addressing ............................................53
Implementing a Real-Time Clock Using 
a Timer1 In terru pt Service ...............................107
Initia lizing PORTA  ......................................................87
Initia lizing PORTB  ......................................................90
Reading a Flash Program Memory Word ...................61
Saving Status, WREG and 
BSR Registers in RAM .......................................85
Writing to Flash Program Memory .......................64–65
Code Protection ...............................................................171
COMF ...............................................................................208
Compare (CCP Module) ...................................................117
CCP Pin Configuration .............................................117
CCPR1 Register .......................................................117
Software Interrupt .....................................................117
Special Event Trigger .......................................113, 117
Timer1/Timer3 Mode Selection ................................117
Compare (CCP1 Module)
Special Event Trigger ...............................................164
Computed GOTO ...............................................................47
Configuration Bits .............................................................171
Context Saving During Interrupts .......................................85
Conversion Considerations ..............................................294
CPFSEQ ..........................................................................208
CPFSGT ...........................................................................209
CPFSLT ...........................................................................209
D
Data EEPRO M Memor y .....................................................67
Associated Registers .................................................70
EEADR Register ........................................................67
EECON1 Register ......................................................67
EECON2 Register ......................................................67
Operation During Code-Protect ..................................70
Protection Against Spurious Write .............................69
Reading ......................................................................69
Using ..........................................................................70
Write Verify .................................................................69
Writing ........................................................................69
Data Memory ..................................................................... 47
General Purpose Registers ....................................... 47
Map for PIC18F1220/1320 Devices ........................... 48
Special Function Registers ........................................ 49
DAW ................................................................................ 210
DC and AC Characteristics
Graphs and Tables .................................................. 269
DC Characteristics ........................................................... 252
Power-Down and Supply Current ............................ 243
Supply Voltage ......................................................... 242
DCFSNZ .......................................................................... 211
DECF ............................................................................... 210
DECFSZ .......................................................................... 211
Demonstration Boards
PICDEM 1 ................................................................ 236
PICDEM 17 .............................................................. 237
PICDEM 18R ........................................................... 237
PICDEM 2 Plus ........................................................ 236
PICDEM 3 ................................................................ 236
PICDEM 4 ................................................................ 236
PICDEM LIN ............................................................ 237
PICDEM USB .......................................................... 237
PICDEM.net Internet/Ethernet ................................. 236
Details on Individual Family Members ................................. 6
Development Support ...................................................... 233
Device Differences ........................................................... 293
Direct Addressing ............................................................... 54
E
Effects of Power Managed Modes on 
Various Clock Sources .............................................. 18
Electrical Characteristics .................................................. 239
Enhanced Capture/Compare/PWM (ECCP) .................... 115
Outputs .................................................................... 116
PWM Mode. See PWM (ECCP Module).
Enhanced PWM Mode. See PWM (ECCP Module). 
Enhanced Universal Synchronous As ynchr onous 
Receiver Transmitter (EUSART) ............................. 131
Equations
16 x 16 Signed Multiplication Algorithm ..................... 72
16 x 16 Unsigned Multiplication Algorithm ................. 72
A/D Minimum Charging Time ................................... 160
Acquisition Time ...................................................... 160
Errata ................................................................................... 4
EUSART
Asynchronous Mode ................................................ 140
12-bit Break Transmit and Receive ................. 146
Associated Registers, Receive ........................ 144
Associated Registers, Transmit ....................... 142
Auto-Wake-up on Sync Break  ......................... 145
Receiver .......................................................... 143
Setting up 9-bit Mode with 
Address Detect  ........................................ 143
Transmitter ....................................................... 140
Baud Rate Generator (BRG) ................................... 135
Associated Registers ....................................... 136
Auto-Baud Rate Detect .................................... 139
Baud Rate Error, Calculating ........................... 135
Baud Rates, Asynchronous Modes  ................. 136
High Baud Rate Select (BRGH Bit) ................. 135
Power Managed Mode Operation .................... 135
Sampling .......................................................... 135
Serial Port Enable (SPEN Bit) ................................. 131

© 2006 Microchip Technology Inc. DS39605D-page 299
PIC18F1220/1320
Synchronous Master Mode ......................................148
Associated Registers, Reception .....................151
Associated Registers, Transmit .......................149
Reception .........................................................150
Transmission ....................................................148
Synchronous Slave Mode ........................................152
Associated Registers, Receive ........................153
Associated Registers, Transmit .......................152
Reception .........................................................153
Transmission ....................................................152
Evaluation and Programming Tools .................................237
F
Fail-Safe Clock Monitor ....................................................171
Exiting Operation .....................................................183
Interrupts in Power Managed Modes .......................183
POR or Wake from Sleep ........................................184
WDT During Oscillator Failure .................................182
Fail-Safe Clock Monitor (FSCM ) ......................................182
Fast Register Stack ............................................................44
Firmware Instructions  .......................................................191
Flash Program Memory ......................................................57
Associated Registers .................................................65
Control Registers .......................................................58
Erase Sequence ........................................................62
Erasing .......................................................................62
Operation During Code-Protect .................................65
Reading ......................................................................61
Table Latch ................................................................60
Table Pointer ..............................................................60
Boundaries Based on Operation ........................60
Table Pointer Boundaries ..........................................60
Table Reads and Table Writes ..................................57
Write Sequence .........................................................63
Writing to ....................................................................63
Unexpected Termination ....................................65
Write Verify ........................................................65
G
GOTO ...............................................................................212
H
Hardware Multiplier ............................................................71
Introduction ................................................................71
Operation ...................................................................71
Performance Comparison ..........................................71
I
I/O Por ts .............................................................................87
ID Locations ............................................................. 171, 188
INCF .................................................................................212
INCFSZ ............................................................................213
In-Circuit Debugger ..........................................................188
In-Circuit Serial Programming (ICSP) ...................... 171, 188
Indirect Addressing ............................................................54
INDF and FSR Registers ...........................................53
Operation ...................................................................53
Indirect Addressing Operation ............................................54
Indirect File Operand ..........................................................47
INFSNZ ............................................................................213
Initialization Conditions for All Registers ...................... 36–38
Instruction Cycle .................................................................45
Instruction Flow/Pipelining .................................................45
Instruction Set .................................................................. 191
ADDLW .................................................................... 197
ADDWF .................................................................... 197
ADDWFC ................................................................. 198
ANDLW .................................................................... 198
ANDWF .................................................................... 199
BC ............................................................................ 199
BCF ......................................................................... 200
BN ............................................................................ 200
BNC ......................................................................... 201
BNN ......................................................................... 201
BNOV ...................................................................... 202
BNZ ......................................................................... 202
BOV ......................................................................... 205
BRA ......................................................................... 203
BSF .......................................................................... 203
BTFSC ..................................................................... 204
BTFSS ..................................................................... 204
BTG ......................................................................... 205
BZ ............................................................................ 206
CALL ........................................................................ 206
CLRF ....................................................................... 207
CLRWDT ................................................................. 207
COMF ...................................................................... 208
CPFSEQ .................................................................. 208
CPFSGT .................................................................. 209
CPFSLT ................................................................... 209
DAW ........................................................................ 210
DCFSNZ .................................................................. 211
DECF ....................................................................... 210
DECFSZ .................................................................. 211
General Format ........................................................ 193
GOTO ...................................................................... 212
INCF ........................................................................ 212
INCFSZ .................................................................... 213
INFSNZ .................................................................... 213
IORLW ..................................................................... 214
IORWF ..................................................................... 214
LFSR ....................................................................... 215
MOVF ...................................................................... 215
MOVFF .................................................................... 216
MOVLB .................................................................... 216
MOVLW ................................................................... 217
MOVWF ................................................................... 217
MULLW .................................................................... 218
MULWF .................................................................... 218
NEGF ....................................................................... 219
NOP ......................................................................... 219
POP ......................................................................... 220
PUSH ....................................................................... 220
RCALL ..................................................................... 221
RESET ..................................................................... 221
RETFIE .................................................................... 222
RETLW .................................................................... 222
RETURN .................................................................. 223
RLCF ....................................................................... 223
RLNCF ..................................................................... 224
RRCF ....................................................................... 224
RRNCF .................................................................... 225
SETF ....................................................................... 225
SLEEP ..................................................................... 226
SUBFWB ................................................................. 226
SUBLW .................................................................... 227

PIC18F1220/1320
DS39605D-page 300 © 2006 Microchip Technology Inc.
SUBWF ....................................................................227
SUBWFB ..................................................................228
SWAPF ....................................................................228
TBLRD .....................................................................229
TBLWT .....................................................................230
TSTFSZ ....................................................................231
XORLW ....................................................................231
XORWF ....................................................................232
Summary Table ........................................................194
INTCON Register
RBIF Bit ......................................................................90
INTCON Registers .............................................................75
Internal Oscillator Block .....................................................14
Adjustment .................................................................14
INTIO Modes ..............................................................14
INTRC Output Frequency ..........................................14
OSCTUNE Register ...................................................14
Internal RC Oscillator
Use with WDT ..........................................................180
Interrupt Sources ..............................................................171
A/D Conversion Complete ........................................159
Capture Complete (CCP) .........................................116
Compare Complete (CCP) .......................................117
Interrupt-on-Change (RB7:RB4) ................................90
INTn Pi n  .....................................................................85
PORTB, Interrupt-on-Change ....................................85
TMR0 .........................................................................85
TMR0 Overflow ........................................................101
TMR1 Overflow ........................................................103
TMR2 to PR2 Match .................................................110
TMR2 to PR2 Match (PWM) ............................109, 119
TMR3 Overflow ................................................111, 113
Interrupts ............................................................................73
Enable Bits
(CCP1 IE Bit)  ....................................................116
Flag Bits
CCP1 Flag (CCP1IF Bit) ..................................116
CCP1IF Flag (CCP1IF Bit) ...............................117
Interrupt-on-Change (RB7:RB4) 
Flag (RBIF Bit) ...........................................90
Logic ...........................................................................74
INTOSC Frequency Drift ....................................................30
IORLW .............................................................................214
IORWF .............................................................................214
IPR Registers .....................................................................82
L
LFSR ................................................................................215
Low-Voltage Detect ..........................................................165
Characteristics .........................................................255
Effects of a Reset .....................................................169
Operation .................................................................168
Current Consumption .......................................169
Reference Voltage Set Point ............................169
Operation During Sleep ............................................169
LVD. See Low-Voltage Detect. 
M
Memory Organization .........................................................41
Data Memory ..............................................................47
Program Mem ory  .......................................................41
Memory Programm ing Requ irements ..............................254
Migration from Baseline to Enhanced Devices ................294
Migration from High-End to Enhanced Devices ...............295
Migration from Mid-Range to 
Enhanced Devices ................................................... 295
MOVF .............................................................................. 215
MOVFF ............................................................................ 216
MOVLB ............................................................................ 216
MOVLW ........................................................................... 217
MOVWF ........................................................................... 217
MPLAB ASM30 Assembler, Linker, Librarian .................. 234
MPLAB ICD 2 In-Circuit Debugger .................................. 235
MPLAB ICE 2000 High-Perf orm ance 
Universal In-Circuit Emulator ................................... 235
MPLAB ICE 4000 High-Perf orm ance 
Universal In-Circuit Emulator ................................... 235
MPLAB Integrated Development 
Environment Software ............................................. 233
MPLAB PM3 Device Pr ogramm er ................................... 235
MPLINK Object Linker/MPL IB Object Librarian ............... 234
MULLW ............................................................................ 218
MULWF ............................................................................ 218
N
NEGF ............................................................................... 219
New Core Features
Multiple Oscillator Options and Features ..................... 5
nanoWatt Technology .................................................. 5
NOP ................................................................................. 219
O
Opcode Field Descriptions ............................................... 192
OPTION_REG Register
PSA Bit .................................................................... 101
T0CS Bit .................................................................. 101
T0PS2: T0 PS0 Bits ................................................... 101
T0SE Bit ................................................................... 101
Oscillator Configuration ...................................................... 11
Crystal/Ceramic Resonator ........................................ 11
EC .............................................................................. 11
ECIO .......................................................................... 11
Extern a l  C l o ck In put ................................................... 13
HS .............................................................................. 11
HSPLL ..................................................................11, 12
INTIO1 ....................................................................... 11
INTIO2 ....................................................................... 11
LP .............................................................................. 11
RC .........................................................................11, 13
RCIO .......................................................................... 11
XT .............................................................................. 11
Oscillator Selection .......................................................... 171
Oscillator Start-up Timer (OST) ............................18, 34, 171
Oscillator Switching ............................................................ 15
Oscillator Transiti ons ......................................................... 18
Oscillator, Timer1 ......................................................103, 113
Oscillator, Timer3 ............................................................. 111
Other Special Features ........................................................ 5
P
Packaging ........................................................................ 287
Details ...................................................................... 288
Marking Information ................................................. 287
PICkit 1 Flash Starter Kit .................................................. 237
PICSTART Plus Deve lopment Program mer .................... 236
PIE Registers ..................................................................... 80

© 2006 Microchip Technology Inc. DS39605D-page 301
PIC18F1220/1320
Pin Functions
MCLR/VPP/RA5 ............................................................8
OSC1/CLKI/RA7 ..........................................................8
OSC2/CLKO/RA6 ........................................................8
RA0/AN0 ......................................................................8
RA1/AN1/LVDIN ..........................................................8
RA2/AN2/VREF- ............................................................8
RA3/AN3/VREF+ ...........................................................8
RA4/T0CKI ...................................................................8
RB0/AN4/INT0 .............................................................9
RB1/AN5/TX/CK/INT1 ..................................................9
RB2/P1B/INT2 .............................................................9
RB3/CCP1/P1A ............................................................9
RB4/AN6/RX/DT/KBI0 .................................................9
RB5/PGM/KBI1 ............................................................9
RB6/PGC/T1OSO/T13CKI/P1C/KBI2 ..........................9
RB7/PGD/T1OSI/P1D/KBI3 .........................................9
VDD ...............................................................................9
VSS ...............................................................................9
Pinout I/O Descriptions
PIC18F1220/1320 ........................................................8
PIR Registers .....................................................................78
PLL Lock Time-out .............................................................34
Pointer, FSR .......................................................................53
POP ..................................................................................220
POR. See Power-on Reset.
PORTA
Associated Registers .................................................89
Functions ...................................................................89
LATA Register ............................................................87
PORTA Register ........................................................87
TRISA Register ..........................................................87
PORTB
Associated Registers .................................................98
Functions ...................................................................98
LATB Register ............................................................90
PORTB Register ........................................................90
RB7:RB4 Interrupt-on-Change 
Flag (RBIF Bit) ...................................................90
TRISB Register ..........................................................90
Postscaler
Timer2 ......................................................................109
WDTAssignment (PSA Bit) ......................................101
Rate Select (T0PS2:T0PS0 Bits) .....................101
Power Managed Modes .....................................................19
Comparison between Run 
and Idle Modes ..................................................20
Entering ......................................................................20
Idle Modes .................................................................21
Multiple Sleep Commands .........................................20
Run Modes .................................................................26
Selecting ....................................................................19
Sleep Mode ................................................................21
Summary (table) ........................................................19
Wake from ..................................................................28
Power-on Reset (POR) .............................................. 34, 171
Power-up Delays ................................................................18
Pow e r-up Timer (PWRT) .......................................18, 34, 171
Prescaler
Capture ....................................................................117
Timer0 ......................................................................101
Assignment (PSA Bit) ......................................101
Rate Select (T0PS2:T0PS0 Bits) .....................101
Timer2 ......................................................................119
PRO MATE II Universal Device Programmer .................. 235
Product Identification System .......................................... 307
Program Counter
PCL Register ............................................................. 44
PCLATH Register ...................................................... 44
PCLATU Register ...................................................... 44
Program Mem ory
Instructions in ............................................................ 46
Interrupt Vector .......................................................... 41
Map and Stack for PIC18F1220 ................................ 41
Map and Stack for PIC18F1320 ................................ 41
Reset Vector .............................................................. 41
Program Verificat ion and Code Protection ...................... 185
Associated Registers ............................................... 185
Configuration Register ............................................. 188
Data EEPROM ......................................................... 188
Program Memory ..................................................... 186
Programm ing, Device Ins tr uctions  ................................... 191
PUSH ............................................................................... 220
PUSH  and POP Instruc t ions .............................................. 43
PWM (CCP Module)
CCPR1H:CCPR1L Registers ................................... 119
Duty Cycle ............................................................... 119
Example Frequencies/Resolution s .......................... 119
Period ...................................................................... 119
TMR2  to  PR 2 M atch  .........................................109, 119
PWM (ECCP Module) ...................................................... 119
Associated Registers ............................................... 130
Direction Change in Full-Bridge 
Output Mode .................................................... 124
Effects o f  a Reset .................................................... 129
Enhanced PWM Auto-Shutdown ............................. 126
Full-Bridge Application Example .............................. 124
Full-Bridge PWM Output 
(Active-High) Diagram ..................................... 123
Half-Bridge Output 
(Active-High) Diagram ..................................... 122
Half-Bridge Output Mode 
Applications Example ...................................... 122
Operation in Low-Power Modes .............................. 129
Output Configurations .............................................. 119
Output Relationships (Active-High) .......................... 120
Output Relationships (Active-Low) .......................... 121
Programmable Dead-Band Delay ............................ 126
PWM Direction Change 
(Active-High) Diagram ..................................... 125
PWM Direction Change at Near 100% 
Duty Cycle (Active-High) Diagram ................... 125
Setup for PWM Operation ........................................ 129
Start-up Considerations ........................................... 128
Q
Q Clock ............................................................................ 119
R
RAM. See Data Me mory.
RCALL ............................................................................. 221
RCIO Oscillator .................................................................. 13
RCON Register
Bit Status During Initializati on .................................... 35
RCSTA Register
SPEN Bit  .................................................................. 131
Register File ....................................................................... 47
Register File Summary .................................................50–51

PIC18F1220/1320
DS39605D-page 302 © 2006 Microchip Technology Inc.
Registers
ADCON0 (A/D Control 0) .........................................155
ADCON1 (A/D Control 1) .........................................156
ADCON2 (A/D Control 2) .........................................157
BAUDCTL (Baud Rate Control) ...............................134
CCP1CON (Enhanced CCP1 Control) .....................115
CONFIG1H (Configuration 1 High) ..........................172
CONFIG2H (Configuration 2 High) ..........................174
CONFIG2L (Configuration 2 Low) ............................173
CONFIG3H (Configuration 3 High) ..........................175
CONFIG4L (Configuration 4 Low) ............................175
CONFIG5H (Configuration 5 High) ..........................176
CONFIG5L (Configuration 5 Low) ............................176
CONFIG6H (Configuration 6 High) ..........................177
CONFIG6L (Configuration 6 Low) ............................177
CONFIG7H (Configuration 7 High) ..........................178
CONFIG7L (Configuration 7 Low) ............................178
DEVID1 (Device ID 1) ..............................................179
DEVID2 (Device ID 2) ..............................................179
ECCPAS (ECCP Auto-Shutdown Control) ...............127
EECON1 (Data EEPROM Control 1) ...................59, 68
INTCON (Interrupt Control)  ........................................75
INTCON2 (Interrupt Control 2) ...................................76
INTCON3 (Interrupt Control 3) ...................................77
IPR1 (Peripheral Interrupt Priority 1) ..........................82
IPR2 (Peripheral Interrupt Priority 2) ..........................83
LVDCON (LVD Control) ...........................................167
OSCCON (Oscillator Control) ....................................17
OSCTUNE (Oscillator Tuning) ...................................15
PIE1 (Peripheral Interrupt Enable 1) ..........................80
PIE2 (Peripheral Interrupt Enable 2) ..........................81
PIR1 (Peripheral Interrupt 
Request (Flag) 1) ...............................................78
PIR2 (Peripheral Interrupt 
Request (Flag) 2) ...............................................79
PWM1CON (PWM Configuration) ............................126
RCON (Reset Control) .........................................56, 84
RCSTA (Receive Status and Control) ......................133
Status .........................................................................55
STKPTR (Stack Pointer) ............................................43
T0CON (Timer0 Control) ............................................99
T1CON (Timer 1 Control) .........................................103
T2CON (Timer 2 Control) .........................................109
T3CON (Timer3 Control) ..........................................111
TXSTA (Transmit Status and Control) .....................132
WDTCON (Watchdog Tim er Contro l) .......................180
RESET .............................................................................221
Reset ..........................................................................33, 171
RETFIE ............................................................................222
RETLW .............................................................................222
RETURN ..........................................................................223
Return Address Stack ........................................................42
and Associated Registers ..........................................42
Return Stack Pointer (STKPTR) ........................................42
Revision History ...............................................................293
RLCF ................................................................................223
RLNCF .............................................................................224
RRCF ...............................................................................224
RRNCF .............................................................................225
S
SETF ................................................................................225
SLEEP ..............................................................................226
Sleep
OSC1 and OSC2 Pin States ......................................18
Software Simulator (MPLAB SIM) .................................... 234
Software Simulator (MPLAB SIM30) ................................ 234
Special Event Trigger. See Compare.
Special Features of the CPU ........................................... 171
Configuration Registers ....................................172–178
Special Function Registers ................................................ 49
Map ............................................................................ 49
Stack Full/Underflow Resets .............................................. 43
SUBFWB ......................................................................... 226
SUBLW ............................................................................ 227
SUBWF ............................................................................ 227
SUBWFB ......................................................................... 228
SWAPF ............................................................................ 228
T
TABLAT Register ............................................................... 60
Table Pointer Operations (table) ........................................ 60
TBLPTR Register ............................................................... 60
TBLRD ............................................................................. 229
TBLWT ............................................................................. 230
Time-out Sequence ........................................................... 34
Timer0 ................................................................................ 99
16-Bit Mode Timer Reads and Writes ...................... 101
Associated Registers ............................................... 101
Clock Source Edge Select (T0SE Bit ) ..................... 101
Clock Source Sel ect  (T0CS  Bit) ............................... 101
Operation ................................................................. 101
Overflow Interrupt .................................................... 101
Prescaler. See Prescaler, Timer0.
Switching Prescaler Assignment ............................. 101
Timer1 .............................................................................. 103
16-Bit Read/Write Mode .......................................... 106
Associated Registers ............................................... 108
Interrupt ................................................................... 106
Operation ................................................................. 104
Oscillator ...........................................................103, 105
Layout Considerations ..................................... 106
Overflow Interrupt .................................................... 103
Resetting, Using a Special Event 
Trigger Output (CCP) ....................................... 106
Special Event Trigger (CCP) ................................... 117
TMR1H Register ...................................................... 103
TMR1L Register ....................................................... 103
Use as a Real-Time Clock ....................................... 107
Timer2 .............................................................................. 109
Associated Registers ............................................... 110
Operation ................................................................. 109
Output ...................................................................... 110
Postscaler. See Postscaler, Timer2.
PR2 Register ....................................................109, 119
Prescaler. See Prescaler, Timer2.
TMR2 Register ......................................................... 109
TMR2  to  PR 2  Match  Interrupt ...................109, 110, 119
Timer3 .............................................................................. 111
Associated Registers ............................................... 113
Operation ................................................................. 112
Oscillator ...........................................................111, 113
Overflow Interrupt .............................................111, 113
Special Event Trigger (CCP) ................................... 113
TMR3H Register ...................................................... 111
TMR3L Register ....................................................... 111

© 2006 Microchip Technology Inc. DS39605D-page 303
PIC18F1220/1320
Timing Diagrams
A/D Conversion ........................................................267
Asynchronous Reception .........................................144
Asynchronous Transmission ....................................141
Asynchronous Transmission 
(Back to Back) ..................................................142
Auto-Wake-up Bit (WUE) During 
Normal Operation .............................................145
Auto-Wake-up Bit (WUE) During Sleep ...................145
Brown-out Reset (BOR) ...........................................262
Capture/Compare/PWM (All CCP Modules) ............264
CLKO and I/O ..........................................................261
Clock/Instruction Cycle ..............................................45
EUSART Synchronous Receiv e 
(Master/Slave) ..................................................266
EUSART SynchronousT rans miss ion 
(Master/Slave) ..................................................265
External Clock (All Modes Except PLL) ...................259
Fail-Safe Clock Monitor ............................................183
Low-Voltage Detect ..................................................168
Low-Voltage Detect Characteristics .........................255
PWM Auto-Shutdown (PRSEN = 0, 
Auto-Restart Disabled) .....................................128
PWM Auto-Shutdown (PRSEN = 1, 
Auto-Restart Enabled) .....................................128
Reset, Watchdog Timer (WDT), 
Oscillator Start-up Timer (OST) and 
Pow e r-up Timer (PWRT) .................................262
Send Break Character Sequenc e ............................147
Slow Rise Time (MCLR Tied to VDD, 
VDD Rise > TPWRT) ............................................40
Synchronous Reception 
(Master Mode, SREN) ......................................150
Synchronous Transmission ......................................148
Synchronous Transmission 
(Through TXEN) ...............................................149
Time-out Sequence on POR w/PLL Enabled 
(MCLR Tied to VDD) ...........................................40
Time-out Sequence on Power-up 
(MCLR Not Tied to VDD), Case 1 .......................39
Time-out Sequence on Power-up 
(MCLR Not Tied to VDD), Case 2 .......................39
Time-out Sequence on Power-up 
(MCLR Tied to VDD, VDD Rise TPWRT) ..............39
Timer0 and Timer1 External Clock ..........................263
Transition for Entry to SEC_IDLE Mode ....................24
Transition for Entry to SEC_RUN Mode ....................26
Transition for Entry to Sleep Mode ............................22
Transition for Two-Speed Start-up 
(INTOSC to HSPLL) ........................................ 181
Transition for Wake from PRI_IDLE Mode ................ 23
Transition for Wake from RC_RUN Mode 
(RC_RUN to PRI_RUN) .................................... 25
Transition for Wake from SEC_RUN Mode 
(HSPLL) ............................................................. 24
Transition for Wake from Sleep (HSPLL) .................. 22
Transition to PRI_IDLE Mode .................................... 23
Transition to RC_IDLE Mode ..................................... 25
Transition to RC_RUN Mode ..................................... 27
Timing Diagrams and Specifications ............................... 259
Capture/Compare/PWM Requirements 
(All CCP Modules) ........................................... 265
CLKO and I/O Requirements ................................... 261
EUSART Synchronous  Receive 
Requirements .................................................. 266
EUSART Synchronous  Transmission 
Requirements .................................................. 265
External Clock Requirements .................................. 259
Internal RC Accuracy ............................................... 260
PLL Clock, HS/HSPLL Mode 
(VDD = 4.2V to 5.5V) ........................................ 260
Reset, Watchdog Timer, Oscillator Start-up 
Timer, Power-up Timer and 
Brown-out Reset Requirements ...................... 263
Timer0 and Timer1 External Clock 
Requirements .................................................. 264
Top-of-Stack Ac cess .......................................................... 42
TSTFSZ ........................................................................... 231
Two-Speed Start-up ..................................................171, 181
Two-Word Instructions ....................................................... 46
Example Cases .......................................................... 46
TXSTA Register
BRGH Bit  ................................................................. 135
W
Watchdog Timer (WDT) ............................................171, 180
Associated Registers ............................................... 181
Control Register ....................................................... 180
During Oscillator Failure .......................................... 182
Programming Considerations .................................. 180
WWW, On-Line Support ...................................................... 4
X
XORLW ............................................................................ 231
XORWF ........................................................................... 232

PIC18F1220/1320

NOTES:

PIC18F1220/1320

THE MICROCHIP WEB SITE

Microc hip pro vides onl ine s upport v ia our W WW site at

www.microchip.c om . Thi s web si te i s us ed as a m ean s

to make files and information easily available to

customers. Accessible by using your favorite Internet

browser, the web site contains the following

information:

•Product Support – Data sheets and errata,

application notes and sample programs, design

resources, user’s guides and hardware support

docume nts , latest softw are releas es and archived

software

•General Technical Support – Frequently Asked

Questions (FAQ), technical support requests,

online dis cu ss io n gr oups, Micro chip con sul tant

program member listing

•Business of Microchip – Product selector and

ordering guides, latest Microchip press releases,

listing of seminars and even ts, listin gs of

Microchip sales offices, distributors and factory

representatives

CUSTOMER CHANGE NOTIFICATION

SERVICE

Microchip’s customer notification service helps keep

customers current on Microchip products. Subscribers

will receive e-mail notification whenever there are

changes, updates, revisions or errata related to a

specif ied produ ct family or develo pment tool of interes t.

To register, access the Microchip web site at

www.microchip.com, click on Customer Change

Notification and follow the registration instructions.

CUSTOMER SUPPORT

Users of Microchip products can receive assistance

through several channels:

• Distributor or Representative

• Local Sales Office

• Field Application Engineer (FAE)

• Technical Support

• Development Systems Information Line

Customers should contact their distributor,

representative or field application engineer (FAE) for

support. Local sales offices are also available to help

customers. A listing of sales offices and locations is

included in the back of this document.

Technical suppo rt is avail able throug h the we b site

at: http://support.microchip.com

PIC18F1220/1320

READER RESPONSE

It is ou r intention to provide you w it h th e b es t documentation po ss ible to ens ure suc c es sfu l u se of y ou r Mic r oc hip pro d-

uct. If you wi sh to prov ide you r comment s on org anizatio n, clar ity, subject matter, and ways in whic h our doc umenta tion

can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150.

Please list the following information, and use this outline to provide us with your comments about this document.

To: Technical Publications Manager

RE: Reader Response Total Pages Sent ________

From: Name

Company

Address

City / State / ZIP / Country

Telephone: (_______) _________ - _________

Application (optional):

Would you like a reply? Y N

Device: Literature Number:

Questions:

FAX: (______) _________ - _________

DS39605DPIC18F1220/1320

1. What are the best features of this document?

2. How does this document meet your hardware and software development needs?

3. Do you find the organization of this document easy to follow? If not, why?

4. What additions to the document do you think would enhance the structure and subject?

5. What deletions from the document could be made without affecting the overall usefulness?

6. Is there any incorrect or misleading information (what and where)?

7. How would you improve this document?

PIC18F1220/1320

PIC18F1220/1320 PR ODUCT IDENTIFICAT ION SYSTEM

To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.

PART NO. −X/XX XXX

PatternPackageTemperature

Range

Device

Device PIC18F1220/1320(1),

PIC18F1220/1320T(2);

VDD range 4.2V to 5.5V

PIC18LF1220/1320(1),

PIC18LF1220/1320T(2);

VDD range 2.5V to 5.5V

Temperature

Range I=-40°C to +85°C(Industrial)

E=-40°C to +125°C (Extended)

Package SO = SOIC SS = SSOP

P=PDIP ML=QFN

Pattern QTP, SQTP, Code or Special Requirements

(blank otherwise)

Examples:

a) PIC18LF1320-I/P 301 = Industrial

temp., PDIP package, Extended

VDD limits, QTP pattern #301.

b) PIC18LF1220-I/SO = Industrial

temp., SOIC package, Extended

VDD limits.

Note 1: F = Standard Voltage range

LF = Wide Voltage Range

2: T = in tape and reel – SOIC

package only

AMERICAS

Corporate Office

2355 West Chandler Blvd.

Chandler, AZ 85224-6199

Tel: 480-792-7200

Fax: 480-792-7277

Technical Support:

http://support.microchip.com

Web Address:

www.microchip.com

Atlanta

Alpharetta, GA

Tel: 770-640-0034

Fax: 770-640-0307

Boston

Westborough, MA

Tel: 774-760-0087

Fax: 774-760-0088

Chicago

Itasc a , IL

Tel: 630-285-0071

Fax: 630-285-0075

Dallas

Addison, TX

Tel: 972-818-7423

Fax: 972-818-2924

Detroit

Farmington Hills, MI

Tel: 248-538-2250

Fax: 248-538-2260

Kokomo

Kokomo, IN

Tel: 765-864-8360

Fax: 765-864-8387

Los A n ge les

Mission Viejo, CA

Tel: 949-462-9523

Fax: 949-462-9608

Santa Clara

Santa Clara, CA

Tel: 408-961-6444

Fax: 408-961-6445

Toronto

Mississauga, Ontario,

Canada

Tel: 905-673-0699

Fax: 905-673-6509

ASIA/PACIFIC

Asia Pacific Office

Suites 3707-14, 37th Floor

Tower 6, The Gateway

Habour City, Kowloon

Hong Kong

Tel: 852-2401-1200

Fax: 852-2401-3431

Australia - Sydney

Tel: 61-2-9868-6733

Fax: 61-2-9868-6755

China - Beijing

Tel: 86-10-8528-2100

Fax: 86-10-8528-2104

China - Chengdu

Tel: 86-28-8665-5511

Fax: 86-28-8665-7889

China - Fuzhou

Tel: 86-591-8750-3506

Fax: 86-591-8750-3521

China - Hong Kong SAR

Tel: 852-2401-1200

Fax: 852-2401-3431

China - Qingdao

Tel: 86-532-8502-7355

Fax: 86-532-8502-7205

China - Shanghai

Tel: 86-21-5407-5533

Fax: 86-21-5407-5066

China - Shenyang

Tel: 86-24-2334-2829

Fax: 86-24-2334-2393

China - Shenzhen

Tel: 86-755-8203-2660

Fax: 86-755-8203-1760

China - Shunde

Tel: 86-757-2839-5507

Fax: 86-757-2839-5571

China - Wuhan

Tel: 86-27-5980-5300

Fax: 86-27-5980-5118

China - Xian

Tel: 86-29-8833-7250

Fax: 86-29-8833-7256

ASIA/PACIFIC

India - Bangalore

Tel: 91-80-4182-8400

Fax: 91-80-4182-8422

India - New Delhi

Tel: 91-11-4160-8631

Fax: 91-11-4160-8632

India - Pune

Tel: 91-20-2566-1512

Fax: 91-20-2566-1513

Japan - Yokohama

Tel: 81-45-471- 6166

Fax: 81-45-471-6122

Korea - Gumi

Tel: 82-54-473-4301

Fax: 82-54-473-4302

Korea - Seoul

Tel: 82-2-554-7200

Fax: 82-2-558-5932 or

82-2-558-5934

Malaysia - Penang

Tel: 60-4-646-8870

Fax: 60-4-646-5086

Philippines - Manila

Tel: 63-2-634-9065

Fax: 63-2-634-9069

Singapore

Tel: 65-6334-8870

Fax: 65-6334-8850

Taiwan - Hsin Chu

Tel: 886-3-572-9526

Fax: 886-3-572-6459

Taiwan - Kaohsiung

Tel: 886-7-536-4818

Fax: 886-7-536-4803

Taiwan - T aipei

Tel: 886-2-2500-6610

Fax: 886-2-2508-0102

Thail a nd - Bangkok

Tel: 66-2-694-1351

Fax: 66-2-694-1350

EUROPE

Austria - Wels

Tel: 43-7242-2244-3910

Fax: 43-7242-2244-393

Denmark - Copenhage n

Tel: 45-4450-2828

Fax: 45-4485-2829

France - Paris

Tel: 33-1-69-53-63-20

Fax: 33-1-69-30-90-79

Germany - Munich

Tel: 49-89-627-144-0

Fax: 49-89-627-14 4-44

Italy - Milan

Tel: 39-0331-742611

Fax: 39-0331-466781

Netherlands - Drunen

Tel: 31-416-690399

Fax: 31-416-690340

Sp ain - Madrid

Tel: 34-91-708-08-90

Fax: 34-91-708-08 -91

UK - Wokingham

Tel: 44-118-921- 5869

Fax: 44-118-921-5820

WORLDWIDE SALES AND SERVICE

08/29/06