SIDACtor (R) Protection Thyristors SLIC Protection Battrax(R) Series - Dual Port Negative - MS-013 Description The Dual Port Negative Battrax(R) Series are programmable SIDACtor(R) devices designed to protect SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. Dual port protection is provided by a programmable device that is referenced to a negative voltage souce while internal diodes provide protection from positive surge events. Features and Benefits t Dual-port protection t Low on-state voltage t Gate trigger tracking device t Does not degrade with use Agency Approvals Agency t Low voltage overshoot t Fails short circuit when surged in excess of ratings Agency File Number E133083 t Integrated diode for positive voltage surges Applicable Global Standards Pinout Designation t TIA-968-A t GR 1089 Intra-building 1 6 t TIA-968-B t IEC 61000-4-5 2 5 t ITU K.20/21 Enhanced Level t YD/T 1082 3 4 t ITU K.20/21 Basic Level t YD/T 950 t YD/T 993 t GR 1089 Inter-building Schematic Symbol 6 (T2) (T1) 1 5 Ground (-VREF) 2 4 (R2) (R1) 3 Electrical Characteristics Part Number Marking VDRM @lDRM=5A VS @100V/s V min V max IH IS mA min mA max IT VT @IT=2.2 Amps VF Capacitance* A max V max V max pF min pF max B1101UC4Lxx B1101UC4 I-VREF* *7* I-VREF* *7* 100 100 2.2 4 5 30 200 B1161UC4Lxx B1161UC4 I-VREF* *7* I-VREF* *7* 160 100 2.2 4 5 30 200 B1201UC4Lxx B1201UC4 I-VREF* *7* I-VREF* *7* 200 100 2.2 4 5 30 200 - VREF Max Value for the negative Battrax is -200 V. - XX = Part Number Suffix: `TP' (Tube Pack) or `RP' (Reel Pack). Notes: - Absolute maximum ratings measured at TA= 25C (unless otherwise noted). - Devices are uni-directional - All electrical characteristics shown are defined from Tip (pin 1 & 6) to Ground (pin 5) and Ring (pin 3 & 4) to Ground (pin 5) (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. * Off-state capacitance (CO) is measured across pins 1 & 5, 3 & 5, 4 & 5, and 6 & 5 at 1 MHz with a 2V bias. 126 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors SLIC Protection Surge Ratings Series IPP ITSM di/dt 0.2x310 0.5x700 2 2x10 2x10 2 8x20 1.2x50 2 10x160 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 50/60 Hz A min A min A min A min A min A min A min A min A min A min A/s max 50 500 400 200 150 200 175 100 200 50 500 1 C 1 1 1 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP $ *PP rating assumes VREFFRVBMT 7 - The device must initially be in thermal equilibrium with -40C < TJ < $ 1 Current waveform in s 2 Voltage waveform in s Thermal Considerations Package Symbol Modified MS-013 Parameter Value Unit TJ Operating Junction Temperature Range UP C TS Storage Temperature Range UP C R0JA Thermal Resistance: Junction to Ambient 60 C/W 6 5 4 1 2 3 V-I Characteristics tr x td Pulse Waveform IPP - Peak Pulse Current - %IPP +I V VREF VS VDRM IF VT -V +V IDRM IH IS IT IPP Waveform = tr x td 50 Half Value 0 1.8 10 IH 8 25 C Ratio of IH (TC = 25C) 2.0 12 4 t - Time (s) Normalized DC Holding Current vs. Case Temperature 14 6 td tr PIN 3 CONNECTED TO VREF Normalized VS Change vs. Junction Temperature Percent of VS Change - % 100 0 PIN CONNECTED TO GROUND Pin 51-2: PIN TOGROUND VREF PIN22CONNECTED CONNECTED TO -I tr = rise time to peak value td = decay time to half value Peak Value 2 0 -4 -6 1.6 1.4 25C 1.2 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 0 20 40 60 80 100 120 140 Case Temperature (TC) - C Junction Temperature (TJ) - C (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. -20 127 Revised: February 22, 2011 160 SIDACtor (R) Protection Thyristors SLIC Protection Soldering Parameters Pb-Free assembly (see Fig. 1) $ $ 60-180 secs. - Temperature Min (Ts(min)) - Temperature Max (Ts(max)) Pre Heat - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3C/sec. Max. TS(max) to TL - Ramp-up Rate 3C/sec. Max. - Temperature (TL) (Liquidus) Reflow Figure 1 TP TL $ - Temperature (tL) 60-150 secs. Peak Temp (TP) tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition tL TS(max) Ramp-down Preheat TS(min) tS $ 25 Time within 5C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6C/sec. Max. Time 25C to Peak Temp (TP) 8 min. Max. Do not exceed time to peak temperature (t 25C to peak) Time $ Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VDC Peak $PS $ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling $UP $ NJOEXFMM VQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC $ 3) VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage $IST.*-45% .FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65C, 1008 hrs. Thermal Shock $UP $ NJOEXFMM TFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) $ 3) BUN VQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat $ TFDT.*-45% .FUIPE Body Material UL recognized epoxy meeting flammability classification 94V-0 Moisture Sensitivity Level 3) $ IST SFnPXDZDMFT $1FBL +&%&$+45% -FWFM Part Marking Part Numbering B1 xx 1 U C 4 L xx TYPE B1: Negative Battrax SIDACtor HOLDING CURRENT 10: 100 mA 20: 200 mA 16: 160 mA CONSTRUCTION VARIABLE PACKING OPTIONS RP: Reel Pack TP: Tube Pack XXXXXXXX RoHS COMPLIANT DUAL PORT IPP RATING Date Code XXXXX PACKAGE TYPE (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Part Marking Code (Refer to Electrical Characteristics Table) 128 Revised: February 22, 2011 SIDACtor (R) Protection Thyristors SLIC Protection Dimensions -- MS-013 Dimensions 0.065 (1.65) Pad Outline C A B C D E F G H J K BSC* 0.460 (11.68) 0.138 (3.50) Dimension are in inches (and millimeters). 0.059 (1.50) E D 7 TYP J 7 TYP A G Burr Side H 96 A Mold Split Line 4 A 7 TYP BSC* F MIN Length of Flat 7 TYP K Detail A B Inches Min Max Min Max 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 --0.143 9.14 8.94 10.16 1.09 1.19 7.44 7.34 2.26 1.04 0.51 3.38 9.25 9.04 10.46 1.13 1.40 7.54 7.44 2.36 1.24 --3.63 * BSC = Basic Spacing between Centers Packing Options Package Type U Description Quantity Added Suffix Industry Standard Modified MS-013 6-pin Tape and Reel Pack 1500 RP EIA-481-D Modified MS-013 6-pin Tube Pack 500 (50 per tube) TP N/A Tape and Reel Specification -- MS-013 .157 (4.0) .630 (16.0) .472 (12.0) 12.99 (330) .512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Specification -- MS-013 Message Location .045 (1.14) .310 (7.87) 90 .165 (4.19) 6 Interior of the Tube .150 (3.81) .225 (5.72) .525 (13.34) (c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. .020 .005 WALL TYP. (0.51 0.13) .108 (2.74) .005 A .110 (2.79) A Dimensions are in inches (and millimeters) 129 Revised: February 22, 2011 20.000 .030 (508.00 0.76) Millimeters