Amphenol Interconnecti on Sol ution Guide Catalogue
ASA200005
Rev 1.b
For further variations and information, consult representative
Amphenol AMEA http://www.amphenol.co.za e-mail: amphenol_africa@csi.com D-1
Specifications are subject to change without notice
All dimensions in mm. P/B – Phosphor Bronze. Ni – Nickel. µ” – Micro inches. AMTA
D
G17 DSub Connector Right Angle PCB Mount
Through-hole DSub connectors male and female.
Materials
Housing – 94V-0 thermoplasti c
Contact s – P/B with 50µ” Ni
Shell – Carbon steel
Board-locks – P/B
Screw-locks – Brass
Electrical
Current – 5A
Voltage – 250VAC/rms 60Hz
Durability
Gold Flash – 75 cycles
15µ” Gold – 125 cycles
30µ” Gold – 250 cycles
Full gold flash – 75 cycl es
Related Information
Panel cut out – Page D-2
PC board layout – Page D-3
DSub Accessori es – Page D-6
Part Number System:
G17X XX XXXXX X
DSub R/ A PCB CONNECTOR VARIATION CODE
Through Hole 2.54mm pitch Blank: Standard
FOOTPRINT FLANGE MOUNTING OPTION
C: 8.08mm 0:
∅3.05m m clear hol e
D: 5mm 1: #4-40 threaded hole
E: 10.4mm 2: #4-40 threaded screw-lock
installed
3: #4-40 threaded hole with
NUMBER OF POSITIONS #4-40 threaded sc rew-lock
09: 9 Posi tion bulk-packed
15: 15 Position 4: M3 threaded hole
25: 25 Posi tion 5: M3 screw-lock i nstalled
37: 37 Posi tion 6: #4-40 threaded hole with
50: 50 Posi tion (G17C only) M2.6 screw-lock bulk-packed
7: #4-40 threaded screw-lock
CONTACT STYLE cl i nch-mounted i n stalled
0: Receptacle
1: Plug BOARD MOUNT OPTION (NOT G17J)
0: None
CONTACT FINISH 1: ∅3.05mm clear hole
0: Gold Flash 2: #4-40 threaded hole
1: 15µ” Gold 3: Arrowhead board-lock
2: 30µ” Gold 4: 4 Claw board-lock (G17C onl y)
3: Full gold flash
FRONT SHELL FINISH
PNS-17C Rev.B/DSUB-G17C0900032X-25 Rev. A 0: Zinc chromate
PNS-17D Rev.B/DSUB-G17D0900131-25 Rev. A 1: Tin/Lead over Nickel
PNS-17E Rev.C/DSUB-G17E0910132- 25 Rev. B 2: Nickel
G17U DSub Connector Right Angle PCB Mount wi th Ferrite
Low cost sol ution for EMI and E MP
Characteristics
Same as G17C Related Information
Same as G17C
Part Number System:
G17U XX XXXXX X
DSub PCB CONNECTOR VARIATION CODE
R/A Through Hole with ferrite Blank: Standard
NUMBER OF POSITIONS SAME AS G17C
09: 9 Posi tion
15: 15 Posi tion
25: 25 Posi tion
37: 37 Posi tion PNS-17U Rev.A/ DS UB - G17UXX0XX31-25 Rev. A
Dimensions
No. of Positions A B C D E
9 30.84 24.99 16.92 16.24 11.09
15 39.24 33.32 24.70 24.56 19.39
25 53.04 47.04 38.96 38.38 33.24
37 69.32 63.50 55.42 54.76 49.86
Impedance Ω
DSub 25MHz 100MHz Range
9
15
25
37
31 50
100MHz
to
300MHz
D
G17K DSub Connector IDC Termination
Ribbon cable mount DSubs.
Materials
Housing – 94V-0 thermoplastic
Pin contacts – Brass with 50µ” Ni
Socket c ontact – P/B with 50µ” Ni
Shell – Carbon steel
Clinch nut – Brass
Screw-locks – Brass
Electrical
Current – 5A
Voltage – 250VAC/rms 60Hz
Durability
Gold Flash – 75 cycles
15µ” Gold – 125 cycles
30µ” Gold – 250 cycles
Full gold flash – 75 cycles
Related Information
Panel cutout – See below
Ribbon cable – 26~28AWG G180
G180 or 3C Page V-1
Access ori es – Page D-6
Part Number System:
G17K XX XXXXX XX
DSub PCB CONNECTOR VARIATION CODE
IDC Termination Blank: Standard
NUMBER OF POSITIONS STRAIN RELIEF OPTION
09: 9 Position 0: None
15: 15 Position 1: With strain relief
25: 25 Position
37: 37 Position FLANGE MOUNTING OPTION
50: 50 Position 0:
∅3.05mm clear hole
1: #4-40 threaded hole
CONTACT STYLE 2: #4-40 threaded screw-lock
0: Receptacle installed
1: Plug 3: #4-40 threaded hole with
#4-40 threaded screw-lock
CONTACT FINIS H bulk-packed
0: Gold Flash 4: M3 threaded hole
1: 15µ” Gold 5: M3 screw-lock installed
2: 30µ” Gold 6: #4-40 threaded hole with
3: Full gold flash M2.6 screw-lock bulk-packed
7: #4-40 threaded screw-lock
FRONT SHELL FINISH clinch-mounted installed
0: Zinc chromate
1: Tin/Lead over Nickel BRACKET OPTION
2: Nickel 0: Without insulator support
3: Whole plastic type 1: With insulator support
Recommended panel cut-outs for DSub Connectors
No. of Contacts Dimensions
Standard High Density
Moun ting type A±0.2 B
±0.2 C±0.2 D±0.1 E±0.1
Front 22.2 25.0 13.0 3.0 2.1
Rigid Rear 20.5 25.0 11.4 3.0 3.4
Front 23.0 25.0 13.8 2.2 2.1
9 15
Float Rear 21.3 25.0 12.2 2.2 3.4
Front 30.5 33.3 13.0 3.0 2.1
Rigid Rear 28.8 33.3 11.4 3.0 3.4
Front 31.3 33.3 13.8 2.2 2.1
15 26 Float Rear 29.6 33.3 12.2 2.2 3.4
Front 44.3 47.0 13.0 3.0 2.1
Rigid Rear 42.5 47.0 11.4 3.0 3.4
Front 45.1 47.0 13.8 2.2 2.1
25 44
Float Rear 43.3 47.0 12.2 2.2 3.4
Front 60.7 63.5 13.0 3.0 2.1
Rigid Rear 59.1 63.5 11.4 3.0 3.4
Front 61.5 63.5 13.8 2.2 2.1
37 62 Float Rear 59.8 63.5 12.2 2.2 3.4
Front 58.3 61.1 15.8 3.0 2.1
Rigid Rear 56.3 61.1 14.9 3.0 3.4
Front 59.2 61.1 16.6 2.2 2.1
50 78
Float Rear 57.1 61.1 14.9 2.2 3.4
Dimensions
No. of Positions A B C D E
9 30.84 24.99 16.92 16.24 11.09
15 39.24 33.32 24.70 24.56 19.39
25 53.04 47.04 38.96 38.38 33.24
37 69.32 63.50 55.42 54.76 49.86
Amphenol Interconnecti on Sol ution Guide Catalogue
ASA200005
Rev 1.b
For further variations and information, consult representative
Amphenol AMEA http://www.amphenol.co.za e-mail: amphenol_africa@csi.com D-2
Specifications are subject to change without notice
All dimensions in mm. P/B – Phosphor Bronze. Ni – Nickel. µ” – Micro inches. AMTA
PNS-G17K Rev.C DSUB-G17K09001001X-25 Rev.B
D
G17M DSub Connector Straddle Mount PCB
Straddle mounted DSub connectors male and female.
Materials
Housing – 94V-0 thermoplastic
Contacts – P/B with 50µ” Ni
Shell – Carbon steel
Clinch nut – Brass
Board-locks – P/B
Screw-locks – Brass
Electrical
Current – 5A
Voltage – 250VAC/rms 60Hz
Durability
Gold Flash – 75 cycles
15µ” Gold – 125 cycles
30µ” Gold – 250 cycles
Full gold flash – 75 cycles
Related Information
Panel cutout – Page D-2
Access ori es – Page D-6
Part Number System:
G17M XX XXXXX X
DSub PCB CONNECTOR VARIATION CODE
Straddle Mount Blank: Standard
0: Short footprint type
NUMBER OF POSITIONS
09: 9 Position FLANGE MOUNTING OPTION
15: 15 Position 0:
∅3.05mm clear hole
25: 25 Position 1: #4-40 threaded hole
37: 37 Position 2: #4-40 threaded screw-lock
installed
CONTACT STYLE 3: #4-40 threaded hol e with
0: Receptacl e #4-40 threaded screw-lock
1: Plug bulk-packed
4: M3 threaded hole
CONTACT FINIS H 5: M3 screw-lock installed
0: Gold Flash 6: #4-40 threaded hole with
1: 15µ” Gold M2.6 screw-lock bulk-packed
2: 30µ” Gold 7: #4-40 threaded screw-lock
3: Full gold flash clinch-mounted installed
FRO NT SHELL FINISH BOARD MOUNT OPTION
0: Zinc chromate 0: None
1: Tin/Lead over Nickel 1: Ø3.05mm clear hole
2: Nickel 2: #4-40 threaded hole
3: M3 threaded hole
4: M3 screw-lock installed
Recommended PCB layout for vertical and right angle DSub Connectors
Dimensions
No. of Positions A B C D E F
9 30.84 24.99 16.92 16.24 11.09 8.31
15 39.24 33.32 24.70 24.56 19.39 16.62
25 53.04 47.04 38.96 38.38 33.24 30.47
37 69.32 63.50 55.42 54.76 49.86 47.09
Amphenol Interconnecti on Sol ution Guide Catalogue
ASA200005
Rev 1.b
For further variations and information, consult representative
Amphenol AMEA http://www.amphenol.co.za e-mail: amphenol_africa@csi.com D-3
Specifications are subject to change without notice
All dimensions in mm. P/B – Phosphor Bronze. Ni – Nickel. µ” – Micro inches. AMTA
PNPNS17MM Rev.C
Amphenol Interconnecti on Sol ution Guide Catalogue
ASA200005
Rev 1.b
For further variations and information, consult representative
Amphenol AMEA http://www.amphenol.co.za e-mail: amphenol_africa@csi.com D-4
Specifications are subject to change without notice
All dimensions in mm. P/B – Phosphor Bronze. Ni – Nickel. µ” – Micro inches. AMTA
D
G17R DSub Connector Rear Release Crimp Type
Crimp type connector for cable application.
Materials
Housing – 94V-0 thermoplasti c
Shell – Carbon steel
Clinch nut – Brass
Screw-locks – Brass
Related Information
Panel cut out – Page D-2
Acc essories – Page D-5/ 6/13
Contacts – See below
Part Number System:
G17R XX XX X X
DSub PCB CONNECTOR VARIATION CODE
Crimp type Cable Mount Blank: Standard
NUMBER OF POSITIONS FLANGE MOUNTING OPTION
09: 9 Position 0:
∅3.05m m clear hol e
15: 15 Posi tion 1: #4-40 threaded hole
25: 25 Posi tion 2: #4-40 threaded screw-lock
37: 37 Posi tion installed
50: 50 Posi tion 3: #4-40 threaded hole with
#4-40 threaded sc rew-lock
CONTACT STYLE bulk-packed
0: Receptacle 4: M3 threaded hole
1: Plug 5: M3 screw-lock installed
6: #4-40 threaded hole with
FRONT SHELL FINISH M2.6 screw-lock bulk-packed
0: Zinc chromate 7: #4-40 threaded screw-lock
1: Tin/Lead over Nickel clinc h-mounted installed
2: Nickel DSUB-G17R09010-25 Rev.A
G17RC DSub Crimp Contacts
For rear insert G17R
Materials
Wire Gauge – 28~22 AWG
Pin Contact – Brass with 50µ ” Ni
Sock et Contact – P/B with 50µ” Ni
Electrical
Current – 5A
Voltage – 250VAC/rms 60Hz
Durability
Gold Flash – 75 cycles
15µ” Gold – 125 cycles
30µ” Gold – 250 cycles
Full gold flash – 75 cycl es
Related Information
Tooling – Cons ul t representat i ve
Part Number System:
G17RC X X X X X X
DSub CRIMP CONTACT VARIATION CODE
Pin and Socket Blank: Standard
CONTACT STYLE WIRE SIZE
0: Femal e 1: AWG #18~#24
1: Male 2: AWG #24~#28
3: AWG #28~#32
CONTACT FINISH
0: Gold Flash PACKING OPTION
1: 15µ” Gold 3: Reel of 5, 000
2: 30µ” Gold 4: Reel of 10,000
3: Full gold flash
PACKING STYLE
0: Right-hand feed PNS-17RC Rev.B
1: Left-hand feed
Dimensions
No. of Positions A B C D E F
9 30.84 24.99 16.92 16.24 11.09 19.28
15 39.24 33.32 24.70 24.56 19.39 27.51
25 53.04 47.04 38.96 38.38 33.24 41.30
37 69.32 63.50 55.42 54.76 49.86 57.71
