Amphenol G17 Interconnection Solution Guide Catalogue ASA200005 Rev 1.b DSub Connector Right Angle PCB Mount Through-hole DSub connectors male and female. Materials D Durability Housing Contacts Shell Board-locks Screw-locks - 94V-0 thermoplastic - P/B with 50" Ni - Carbon steel - P/B - Brass Gold Flash 15" Gold 30" Gold Full gold flash Related Information Electrical Current Voltage - 75 cycles - 125 cycles - 250 cycles - 75 cycles Panel cutout - Page D-2 PC board layout - Page D-3 DSub Accessories - Page D-6 - 5A - 250VAC/rms 60Hz Part Number System: G17X XX XXXXX X DSub R/A PCB CONNECTOR Through Hole 2.54mm pitch VARIATION CODE Blank: Standard FOOTPRINT C: 8.08mm D: 5mm E: 10.4mm FLANGE MOUNTING OPTION 0: 3.05mm clear hole 1: #4-40 threaded hole 2: #4-40 threaded screw-lock installed 3: #4-40 threaded hole with #4-40 threaded screw-lock bulk-packed 4: M3 threaded hole 5: M3 screw-lock installed 6: #4-40 threaded hole with M2.6 screw-lock bulk-packed 7: #4-40 threaded screw-lock clinch-mounted installed NUMBER OF POSITIONS 09: 9 Position 15: 15 Position 25: 25 Position 37: 37 Position 50: 50 Position (G17C only) CONTACT STYLE 0: Receptacle 1: Plug BOARD MOUNT OPTION (NOT G17J) 0: None 1: 3.05mm clear hole 2: #4-40 threaded hole 3: Arrowhead board-lock 4: 4 Claw board-lock (G17C only) CONTACT FINISH 0: Gold Flash 1: 15" Gold 2: 30" Gold 3: Full gold flash FRONT SHELL FINISH 0: Zinc chromate 1: Tin/Lead over Nickel 2: Nickel PNS-17C Rev.B/DSUB-G17C0900032X-25 Rev. A PNS-17D Rev.B/DSUB-G17D0900131-25 Rev. A PNS-17E Rev.C/DSUB-G17E0910132-25 Rev. B No. of Positions 9 15 25 37 G17U A 30.84 39.24 53.04 69.32 B 24.99 33.32 47.04 63.50 Dimensions C 16.92 24.70 38.96 55.42 D 16.24 24.56 38.38 54.76 E 11.09 19.39 33.24 49.86 DSub Connector Right Angle PCB Mount with Ferrite Low cost solution for EMI and EMP Characteristics Related Information Same as G17C Same as G17C Part Number System: G17U XX XXXXX X DSub PCB CONNECTOR R/A Through Hole with ferrite NUMBER OF POSITIONS 09: 9 Position 15: 15 Position 25: 25 Position 37: 37 Position VARIATION CODE Blank: Standard SAME AS G17C PNS-17U Rev.A/DSUB-G17UXX0XX31-25 Rev. A DSub 9 15 25 37 Impedance 25MHz 100MHz 31 50 Range 100MHz to 300MHz For further variations and information, consult representative Amphenol AMEA http://www.amphenol.co.za e-mail: amphenol_africa@csi.com Specifications are subject to change without notice All dimensions in mm. P/B - Phosphor Bronze. Ni - Nickel. " - Micro inches. D-1 AMTA Amphenol G17K Interconnection Solution Guide Catalogue ASA200005 Rev 1.b DSub Connector IDC Termination Ribbon cable mount DSubs. Materials Housing Pin contacts Socket contact Shell Clinch nut Screw-locks Durability - 94V-0 thermoplastic - Brass with 50" Ni - P/B with 50" Ni - Carbon steel - Brass - Brass Electrical Current Voltage - 5A - 250VAC/rms 60Hz Gold Flash 15" Gold 30" Gold Full gold flash - 75 cycles - 125 cycles - 250 cycles - 75 cycles D Related Information Panel cutout Ribbon cable - See below - 26~28AWG G180 G180 or 3C Page V-1 - Page D-6 Accessories Part Number System: G17K XX XXXXX XX DSub PCB CONNECTOR IDC Termination VARIATION CODE Blank: Standard NUMBER OF POSITIONS 09: 9 Position 15: 15 Position 25: 25 Position 37: 37 Position 50: 50 Position STRAIN RELIEF OPTION 0: None 1: With strain relief FLANGE MOUNTING OPTION 0: 3.05mm clear hole 1: #4-40 threaded hole 2: #4-40 threaded screw-lock installed 3: #4-40 threaded hole with #4-40 threaded screw-lock bulk-packed 4: M3 threaded hole 5: M3 screw-lock installed 6: #4-40 threaded hole with M2.6 screw-lock bulk-packed 7: #4-40 threaded screw-lock clinch-mounted installed CONTACT STYLE 0: Receptacle 1: Plug CONTACT FINISH 0: Gold Flash 1: 15" Gold 2: 30" Gold 3: Full gold flash FRONT SHELL FINISH 0: Zinc chromate 1: Tin/Lead over Nickel 2: Nickel 3: Whole plastic type No. of Positions 9 15 25 37 BRACKET OPTION 0: Without insulator support 1: With insulator support A 30.84 39.24 53.04 69.32 B 24.99 33.32 47.04 63.50 Dimensions C 16.92 24.70 38.96 55.42 D 16.24 24.56 38.38 54.76 E 11.09 19.39 33.24 49.86 PNS-G17K Rev.C DSUB-G17K09001001X-25 Rev.B Recommended panel cut-outs for DSub Connectors No. of Contacts Standard High Density Mounting type Rigid 9 15 Float Rigid 15 26 Float Rigid 25 44 Float Rigid 37 62 Float Rigid 50 78 Float Front Rear Front Rear Front Rear Front Rear Front Rear Front Rear Front Rear Front Rear Front Rear Front Rear A0.2 22.2 20.5 23.0 21.3 30.5 28.8 31.3 29.6 44.3 42.5 45.1 43.3 60.7 59.1 61.5 59.8 58.3 56.3 59.2 57.1 B0.2 25.0 25.0 25.0 25.0 33.3 33.3 33.3 33.3 47.0 47.0 47.0 47.0 63.5 63.5 63.5 63.5 61.1 61.1 61.1 61.1 Dimensions C0.2 13.0 11.4 13.8 12.2 13.0 11.4 13.8 12.2 13.0 11.4 13.8 12.2 13.0 11.4 13.8 12.2 15.8 14.9 16.6 14.9 D0.1 3.0 3.0 2.2 2.2 3.0 3.0 2.2 2.2 3.0 3.0 2.2 2.2 3.0 3.0 2.2 2.2 3.0 3.0 2.2 2.2 E0.1 2.1 3.4 2.1 3.4 2.1 3.4 2.1 3.4 2.1 3.4 2.1 3.4 2.1 3.4 2.1 3.4 2.1 3.4 2.1 3.4 For further variations and information, consult representative Amphenol AMEA http://www.amphenol.co.za e-mail: amphenol_africa@csi.com Specifications are subject to change without notice All dimensions in mm. P/B - Phosphor Bronze. Ni - Nickel. " - Micro inches. D-2 AMTA Amphenol G17M Interconnection Solution Guide Catalogue ASA200005 Rev 1.b DSub Connector Straddle Mount PCB Straddle mounted DSub connectors male and female. Materials D Housing Contacts Shell Clinch nut Board-locks Screw-locks Durability - 94V-0 thermoplastic - P/B with 50" Ni - Carbon steel - Brass - P/B - Brass Electrical Current Voltage Gold Flash 15" Gold 30" Gold Full gold flash - 75 cycles - 125 cycles - 250 cycles - 75 cycles Related Information Panel cutout Accessories - Page D-2 - Page D-6 - 5A - 250VAC/rms 60Hz Part Number System: G17M XX XXXXX X DSub PCB CONNECTOR Straddle Mount VARIATION CODE Blank: Standard 0: Short footprint type NUMBER OF POSITIONS 09: 9 Position 15: 15 Position 25: 25 Position 37: 37 Position FLANGE MOUNTING OPTION 0: 3.05mm clear hole 1: #4-40 threaded hole 2: #4-40 threaded screw-lock installed 3: #4-40 threaded hole with #4-40 threaded screw-lock bulk-packed 4: M3 threaded hole 5: M3 screw-lock installed 6: #4-40 threaded hole with M2.6 screw-lock bulk-packed 7: #4-40 threaded screw-lock clinch-mounted installed CONTACT STYLE 0: Receptacle 1: Plug CONTACT FINISH 0: Gold Flash 1: 15" Gold 2: 30" Gold 3: Full gold flash FRONT SHELL FINISH 0: Zinc chromate 1: Tin/Lead over Nickel 2: Nickel No. of Positions 9 15 25 37 A 30.84 39.24 53.04 69.32 BOARD MOUNT OPTION 0: None 1: O3.05mm clear hole 2: #4-40 threaded hole 3: M3 threaded hole 4: M3 screw-lock installed B 24.99 33.32 47.04 63.50 Dimensions C D 16.92 16.24 24.70 24.56 38.96 38.38 55.42 54.76 E 11.09 19.39 33.24 49.86 F 8.31 16.62 30.47 47.09 PNPNS17MM Rev.C Recommended PCB layout for vertical and right angle DSub Connectors For further variations and information, consult representative Amphenol AMEA http://www.amphenol.co.za e-mail: amphenol_africa@csi.com Specifications are subject to change without notice All dimensions in mm. P/B - Phosphor Bronze. Ni - Nickel. " - Micro inches. D-3 AMTA Amphenol G17R Interconnection Solution Guide Catalogue ASA200005 Rev 1.b DSub Connector Rear Release Crimp Type Crimp type connector for cable application. Materials Related Information Housing Shell Clinch nut Screw-locks - 94V-0 thermoplastic - Carbon steel - Brass - Brass Panel cutout Accessories Contacts - Page D-2 - Page D-5/6/13 - See below D Part Number System: G17R XX XX X X DSub PCB CONNECTOR Crimp type Cable Mount VARIATION CODE Blank: Standard NUMBER OF POSITIONS 09: 9 Position 15: 15 Position 25: 25 Position 37: 37 Position 50: 50 Position FLANGE MOUNTING OPTION 0: 3.05mm clear hole 1: #4-40 threaded hole 2: #4-40 threaded screw-lock installed 3: #4-40 threaded hole with #4-40 threaded screw-lock bulk-packed 4: M3 threaded hole 5: M3 screw-lock installed 6: #4-40 threaded hole with M2.6 screw-lock bulk-packed 7: #4-40 threaded screw-lock clinch-mounted installed CONTACT STYLE 0: Receptacle 1: Plug FRONT SHELL FINISH 0: Zinc chromate 1: Tin/Lead over Nickel 2: Nickel No. of Positions A 30.84 39.24 53.04 69.32 9 15 25 37 G17RC DSUB-G17R09010-25 Rev.A B 24.99 33.32 47.04 63.50 Dimensions C D 16.92 16.24 24.70 24.56 38.96 38.38 55.42 54.76 E 11.09 19.39 33.24 49.86 F 19.28 27.51 41.30 57.71 DSub Crimp Contacts For rear insert G17R Durability Materials Wire Gauge Pin Contact Socket Contact - 28~22 AWG - Brass with 50" Ni - P/B with 50" Ni Gold Flash 15" Gold 30" Gold Full gold flash - 5A - 250VAC/rms 60Hz Related Information Electrical Current Voltage - 75 cycles - 125 cycles - 250 cycles - 75 cycles - Consult representative Tooling Part Number System: G17RC X X X X X X DSub CRIMP CONTACT Pin and Socket VARIATION CODE Blank: Standard CONTACT STYLE 0: Female 1: Male WIRE SIZE 1: AWG #18~#24 2: AWG #24~#28 3: AWG #28~#32 CONTACT FINISH 0: Gold Flash 1: 15" Gold 2: 30" Gold 3: Full gold flash PACKING OPTION 3: Reel of 5,000 4: Reel of 10,000 PACKING STYLE 0: Right-hand feed 1: Left-hand feed PNS-17RC Rev.B For further variations and information, consult representative Amphenol AMEA http://www.amphenol.co.za e-mail: amphenol_africa@csi.com Specifications are subject to change without notice All dimensions in mm. P/B - Phosphor Bronze. Ni - Nickel. " - Micro inches. D-4 AMTA