8100617EA/MLB - Intersil Corporation

REVISIONS

LTR DESCRIPTION DATE (YR-MO-DA) APPROVED

F

Add peak current to absolute maximum ratings. Editorial changes throughout. 92-11-24 M. A. FRYE

G

Changes in accordance with NOR 5962-R144-95. 95-10-20 M. A. FRYE

H

Make corrections to the switch operation table in 3.3.1. Update boilerplate to

reflect current requirements. -rrp

03-03-10 R. MONNIN

J

Make correction to marking paragraph 3.5. -rrp 05-05-11 R. MONNIN

THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.

CURRENT CAGE CODE 67268

REV

SHEET

REV

SHEET

REV STATUS REV J J J J J J J J J J J J

OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12

PMIC N/A PREPARED BY

GARY J. ZAHN

DEFENSE SUPPLY CENTER COLUMBUS

STANDARD

MICROCIRCUIT

DRAWING

CHECKED BY

WILLIAM E. SHARP COLUMBUS, OHIO 43218-3990

http://www.dscc.dla.mil

THIS DRAWING IS AVAILABLE

FOR USE BY ALL

DEPARTMENTS

APPROVED BY

N. A. HAUCK

MICROCIRCUIT, LINEAR, CMOS, HIGH LEVEL

ANALOG SWITCHES WITH DRIVERS,

MONOLITHIC SILICON

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

DRAWING APPROVAL DATE

81-10-01

AMSC N/A

REVISION LEVEL

J SIZE

A CAGE CODE

14933

81006

SHEET

1 OF

12

DSCC FORM 2233

APR 97 5962-E329-05

STANDARD

MICROCIRCUIT DRAWING

SIZE

A

81006

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

J SHEET 2

DSCC FORM 2234

APR 97

1. SCOPE

1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in

accordance with MIL-PRF-38535, appendix A.

1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:

81006 01 X X

Drawing number Device type

(see 1.2.1) Case outline

(see 1.2.2) Lead finish

(see 1.2.3)

1.2.1 Device type(s). The device type(s) identify the circuit function as follows:

Device type Generic number Circuit function

01 IH5040, DG5140 One-channel, 75 ohms, SPST switch

02 IH5041, DG5141 Two-channel, 75 ohms, SPST switch

03 IH5042, DG5142 One-channel, 75 ohms, SPDT switch

04 IH5043, DG5143 Two-channel, 75 ohms, SPDT switch

05 IH5044, DG5144 One-channel, 75 ohms, DPST switch

06 IH5045, DG5145 Two-channel, 75 ohms, DPST switch

07 IH5046 One-channel, 75 ohms, DPDT switch

08 IH5047 One-channel, 75 ohms, 4PST switch

09 IH5140, HI5040 One-channel, 75 ohms, SPST switch

10 IH5141, HI5041 Two-channel, 75 ohms, SPDT switch

11 IH5142, HI5042 One-channel, 75 ohms, SPDT switch

12 IH5143, HI5043 Two-channel, 30 ohms, SPDT switch

13 IH5144, HI5044 One-channel, 30 ohms, DPST switch

14 IH5145, HI5045 Two-channel, 75 ohms, DPST switch

15 HI5046 One-channel, 75 ohms, DPDT switch

16 IH5047, HI5047 One-channel, 75 ohms, 4PST switch

17 HI5046A One-channel, 30 ohms, DPDT switch

18 HI5047A One-channel, 30 ohms, 4PST switch

19 IH5148, HI5048 Two-channel, 30 ohms, SPST switch

20 IH5149, HI5049 Two-channel, 30 ohms, DPST switch

21 IH5150, HI5050 One-channel, 30 ohms, SPDT switch

22 IH5151, HI5051 Two-channel, 30 ohms, SPDT switch

1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:

Outline letter Descriptive designator Terminals Package style

A GDFP5-F14 or CDFP6-F14 14 Flat pack

E GDIP1-T16 or CDIP2-T16 16 Dual-in-line

I MACY1-X10 10 Can

2 CQCC1-N20 20 Square leadless chip carrier

X CDFP3-F14 14 Flat pack

1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.

STANDARD

MICROCIRCUIT DRAWING

SIZE

A

81006

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

J SHEET 3

DSCC FORM 2234

APR 97

1.3 Absolute maximum ratings.

V+ - V-.................................................................................... 33 V dc

V+ - VD.................................................................................... 30 V dc

V

D - V-..................................................................................... 30 V dc

V

D - VS.................................................................................... ±22 V dc

V

L - V-..................................................................................... 33 V dc

V

L - VIN.................................................................................... 30 V dc

V

L - VR.................................................................................... 20 V dc

V

IN - VR................................................................................... 20 V dc

V

R - V-..................................................................................... 33 V dc

V

R - VIN ................................................................................... 2 V dc

Current (any terminal except S or D)...................................... 30 mA

Peak current (source to drain) .............................................. 80 mA 1/

Storage temperature range..................................................... -65°C to +150°C

Lead temperature (soldering, 10 seconds) ............................. +300°C

Junction temperature (TJ)....................................................... +175°C

Power dissipation, (PD): 2/

Cases A and X at TA = +125°C ........................................... 350 mW

Case E at TA = +125°C ....................................................... 400 mW

Case I at TA = +125°C ........................................................ 350 mW

Case 2 at TA = +125°C ....................................................... 350 mW

1.4 Recommended operating conditions.

+VCC ...................................................................................... +15 V dc

-VCC ....................................................................................... -15 V dc

V

R .......................................................................................... 0 V dc

V

L ........................................................................................... 5 V dc

Ambient operating temperature range (TA)............................. -55°C to +125°C

Thermal resistance, junction-to-case (θJC).............................. See MIL-STD-1835

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a

part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in

the solicitation or contract.

DEPARTMENT OF DEFENSE SPECIFICATION

MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.

DEPARTMENT OF DEFENSE ST ANDARDS

MIL-STD-883 - Test Method Standard Microcircuits.

MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.

1/ Pulse at 1 ms, 10 percent duty cycle maximum.

2/ For TA = +100°C to +125°C, derate linearly at 12 mW/°C.

STANDARD

MICROCIRCUIT DRAWING

SIZE

A

81006

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

J SHEET 4

DSCC FORM 2234

APR 97

DEPARTMENT OF DEFENSE HANDBOOKS

MIL-HDBK-103 - List of Standard Microcircuit Drawings.

MIL-HDBK-780 - Standard Microcircuit Drawings.

(Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil or

from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text

of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-

JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer

Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-

PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying

activity approval in accordance with MIL-PRF -38535. This QML flow as documented in the Quality Management (QM) plan

may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.

These modifications shall not affect the PIN as described herein. A “Q” or “QML” certification mark in accordance with MIL-

PRF-38535 is required to identify when the QML flow option is used.

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified

in MIL-PRF-38535, appendix A and herein.

3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.

3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are

as specified in table I and shall apply over the full ambient operating temperature range.

3.3.1 Switch operation. The analog switches listed below are guaranteed to turn “on” with either a “low” input

(VR ≤ VIL ≤ 0.8 V) or “high” input (2.4 V ≤ VIH ≤ VIL) as specified below (see figure 1).

Device types VIN Channels ON Channels OFF

2.4 V dc 1 01, 09 0.8 V dc 1

2.4 V dc 1, 2 02, 10, 05, 13,

19 0.8 V dc 1, 2

2.4 V dc 1 2 03, 11, 21 0.8 V dc 2 1

2.4 V dc 1, 2 3, 4 04, 12, 22 0.8 V dc 3, 4 1, 2

2.4 V dc 2, 3 1, 4 07, 15, 17 0.8 V dc 1, 4 2, 3

2.4 V dc 1, 2, 3, 4 06, 08, 14, 16,

18, 20 0.8 V dc 1, 2, 3, 4

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical

tests for each subgroup are described in table I.

3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed

in 1.2 herein. In addition, the manufacturer’s PIN may also be marked.

3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance

to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q” or “QML” certification mark in

accordance with MIL-PRF-38535 to identify when the QML flow option is used.

STANDARD

MICROCIRCUIT DRAWING

SIZE

A

81006

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

J SHEET 5

DSCC FORM 2234

APR 97

TABLE I. Electrical performance characteristics.

Test

Symbol

Conditions

-55°C ≤ TA ≤ +125°C

VCC = ±15 V

unless otherwise specified

Group A

subgroups

Device

type

Limits Unit

Min Max

1, 3 75

2 1 - 16 150

1, 3 45

VD = -10 V, IS = 10 mA,

2 17 - 22 50

1, 3 75

2 1 - 16 150

1, 3 45

VD = 10 V, IS = -10 mA,

2 17 - 22 50

1, 3 75 VD = -7.5 V, IS = 10 mA,

VCC = ±10 V 2/ 2 150

1, 3 75

Drain source “ON”

resistance

RDS

VD = 7.5 V, IS = -10 mA,

VCC = ±10 V 2/ 2

All

150

Ω 1/

2, 3 -200 200 VS = VD = 10 V,

See 3.3.1 for VIN 1 -2 2

2, 3 -200 200

Channel “ON” leakage

current

ID(ON)

VS = VD = -10 V,

See 3.3.1 for VIN 1

All

-2 2

nA

2, 3 -100 100 VS = -10 V, VD = 10 V,

See 3.3.1 for VIN 1 -1 1

2, 3 -100 100

Drain “OFF” leakage current ID(OFF)

VS = 10 V, VD = -10 V,

See 3.3.1 for VIN 1

All

-1 1

nA

2, 3 -100 100 VS = 10 V, VD = -10 V,

See 3.3.1 for VIN 1 -1 1

2, 3 -100 100

Source “OFF” leakage

current IS(OFF)

VS = -10 V, VD = 10 V,

See 3.3.1 for VIN 1

All

-1 1

nA

1, 3 -1 1 Input current, input voltage

low IIL V

IN = 0 V 2 All -10 1

µA

1, 3 -1 1 Input current, input voltage

high IIH V

IN = 2.4 V, 5 V 2 All -1 10

µA

1, 3 10

2 1-8 100

1 200

Positive supply current +ICC V

IN = 0 V, 5 V

2, 3 9 - 22 300

µA

1, 3 -10

2 1 - 8 -100

1 -200

Negative supply current -ICC V

IN = 0 V, 5 V

2, 3 9 - 22 -300

µA

See footnotes at end of table.

STANDARD

MICROCIRCUIT DRAWING

SIZE

A

81006

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

J SHEET 6

DSCC FORM 2234

APR 97

TABLE I. Electrical performance characteristics – Continued.

Test

Symbol

Conditions

-55°C ≤ TA ≤ +125°C

VCC = ±15 V

unless otherwise specified

Group A

subgroups

Device

type

Limits Unit

Min Max

1, 3 10

2 1 - 8 100

1 -200

Logic supply current +IL V

IN = 0 V, 5 V

2, 3 9 - 22 -300

µA

1, 3 -10

2 1 - 8 -100

1 -200

Reference supply current +IR V

IN = 0 V, 5 V

2, 3 9 - 22 -300

µA

11 375

9 450

10

1 - 8

550

11 450

9 500

Turn-on time tON

10

9 - 22

800

ns

11 250

9 250

10

1 - 8

400

11 350

9 450

Turn-off time tOFF

10

9 - 22

600

ns

Single channel isolation 2/ VISO RL = 100 Ω, f = 100 kHz,

VIN = 2 VP-P, CL = 5 pF,

TA = +25°C

9 All 60 dB

Crosstalk between channels

2/

VCT RL = 100 Ω, f = 100 kHz,

VIN = 2 VP-P, CL = 5 pF,

TA = +25°C

9 All 60 dB

Charge transfer error 2/ VCTE V

IN = 0 V, CL = 10 nF,

TA = +25°C 9 All 30 mV

Break before make time

delay 2/ tD TA = +25°C 9 03, 04,

07 5 ns

Driver input capacitance 2/ CA VIN = 0 V, TA = +25°C 9 All 45 pF

Switch input capacitance

2/ CIS Switch off, TA = +25°C 9 All 60 pF

Switch output capacitance

2

COS Switch off, TA = +25°C 9 All 60 pF

1/ The listed resistance limits correspond to the following voltage values:

45 Ω and 75 Ω − ±9.25 V, ±6.75 V

50 Ω and 150 Ω - ±8.50 V, ±6.0 V

2/ If not tested, shall be guaranteed to the limits specified in table I herein.

STANDARD

MICROCIRCUIT DRAWING

SIZE

A

81006

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

J SHEET 7

DSCC FORM 2234

APR 97

Device type 01 Device types 01 and 09 Device type 09 only

Case outline A Case outline E Case outline I

Device type 02 Device types 02 and 10 Device type 19

Case outline A Case outline E Case outline E

FIGURE 1. Terminal connections.

STANDARD

MICROCIRCUIT DRAWING

SIZE

A

81006

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

J SHEET 8

DSCC FORM 2234

APR 97

Device types 02 and 10 Device type 03 Device types 03, 11, and 21

Case outline I Case outline A Case outline E

Device type 04 Device types 04, 12, and 22

Case outline A Case outline E Case outline 2

FIGURE 1. Terminal connections – Continued.

STANDARD

MICROCIRCUIT DRAWING

SIZE

A

81006

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

J SHEET 9

DSCC FORM 2234

APR 97

Device type 05 Device types 05 and 13

Case outline A Case outline E Case outline I

Device type 06 Device types 06, 14, and 20

Case outline A and X Case outline E Case outline 2

FIGURE 1. Terminal connections – Continued.

STANDARD

MICROCIRCUIT DRAWING

SIZE

A

81006

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

J SHEET 10

DSCC FORM 2234

APR 97

Device type 07 Device types 07, 15, and 17

Case outline A Case outline E

Device type 08 Device types 08, 16, and 18

Case outline A Case outline E

FIGURE 1. Terminal connections – Continued.

STANDARD

MICROCIRCUIT DRAWING

SIZE

A

81006

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

J SHEET 11

DSCC FORM 2234

APR 97

3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an

approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to

listing as an approved source of supply shall affirm that the manufacturer’s product meets the requirements of MIL-PRF-38535,

appendix A and the requirements herein.

3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided

with each lot of microcircuits delivered to this drawing.

3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing.

3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's

facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the

reviewer.

4. VERIFICATION

4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,

appendix A.

4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices

prior to quality conformance inspection. The following additional criteria shall apply:

a. Burn-in test, method 1015 of MIL-STD-883.

(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level

control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify

the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method

1015 of MIL-STD-883.

(2) TA = +125°C, minimum.

b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter

tests prior to burn-in are optional at the discretion of the manufacturer.

4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-ST D-

883 including groups A, B, C, and D inspections. The following additional criteria shall apply.

4.3.1 Group A inspection.

a. Tests shall be as specified in table II herein.

b. Subgroups 4, 5, 6, 7, and 8 in table I, method 5005 of MIL-STD-883 shall be omitted.

STANDARD

MICROCIRCUIT DRAWING

SIZE

A

81006

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990 REVISION LEVEL

J SHEET 12

DSCC FORM 2234

APR 97

TABLE II. Electrical test requirements.

MIL-STD-883 test requirements Subgroups

(in accordance with

MIL-STD-883, method 5005,

table I)

Interim electrical parameters

(method 5004) ----

Final electrical test parameters

(method 5004) 1*, 2, 3

Group A test requirements

(method 5005) 1, 2, 3, 9, 10, 11

Groups C and D end-point

electrical parameters

(method 5005)

1

* PDA applies to subgroup 1.

4.3.2 Groups C and D inspections.

a. End-point electrical parameters shall be as specified in table II herein.

b. Steady-state life test conditions, method 1005 of MIL-STD-883.

(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision

level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall

specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in

method 1005 of MIL-STD-883.

(2) TA = +125°C, minimum.

(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.

5. PACKAGING

5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.

6. NOTES

6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications

(original equipment), design applications, and logistics purposes.

6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-

prepared specification or drawing.

6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for

the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.

6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system

application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be

used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC

5962) should contact DSCC-VA, telephone (614) 692-0544.

6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone

(614) 692-0547

6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-

HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by

DSCC-VA.

STANDARD MICROCIRCUIT DRAWING BULLETIN

DATE: 05-05-11

Approved sources of supply for SMD 81006 are listed below for immediate acquisition information only and shall be

added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to

include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of

compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the next

dated revision of MIL-HDBK-103 and QML-38535. DSCC maintains an online database of all current sources of

supply at http://www.dscc.dla.mil/Programs/Smcr/ .

Standard

microcircuit drawing

PIN 1/

Vendor

CAGE

number

Vendor

similar

PIN 2/

Reference military

specification

8100601AA 3/ IH5040MFD M38510/10501BAA

8100601EA 1ES66 IH5040MJE/883B M38510/10501BEA

3/ DG5140AK

8100602AA 3/ IH5041MFD M38510/10502BAA

8100602EA 1ES66 IH5041MJE/883B M38510/10502BEA

3/ DG5141AK

8100602IA 3/ DG5141AA M38510/10502BIA

8100603AA 3/ IH5042MFD M38510/10503BAA

8100603EA 1ES66 IH5042MJE/883B M38510/10503BEA

3/ DG5142AK

8100604AA 3/ IH5043MFD M38510/10504BAA

8100604EA 3/ IH5043MJE M38510/10504BEA

1ES66 IH5043MJE/883B

3/ DG5143AK

8100605AA 3/ IH5044MFD M38510/10505BAA

8100605EA 1ES66 IH5044MJE/883B M38510/10505BEA

3/ DG5144AK

8100605IA 3/ DG5144AA M38510/10505BIA

8100606AA 3/ IH5045MFD/883B M38510/10506BAA

8100606EA 1ES66 IH5045MJE/883B M38510/10506BEA

3/ DG5145AK

8100606XC 1ES66 IH5045MFD/883B

8100607AA 3/ IH5046MFD M38510/10507BAA

8100607EA 3/ IH5046MJE M38510/10507BEA

8100608AA 3/ IH5047MFD M38510/10508BAA

8100608EA 1ES66 IH5047MJE/883B M38510/10508BEA

8100609EA 1ES66 IH5140MJE/883B M38510/10501BEA

3/ HI1-5040/883

8100609IA 3/ DG5040AA M38510/10501BIA

See footnotes at end of table.

1 of 3

STANDARD MICROCIRCUIT DRAWING BULLETIN – Continued.

Standard

microcircuit drawing

PIN 1/

Vendor

CAGE

number

Vendor

similar

PIN 2/

Reference military

specification

8100610EA 1ES66 IH5141MJE/883B M38510/10502BEA

3/ IH5141MJE

3/ HI1-5041/883

8100610IA 3/ DG5041AA M38510/10502BIA

8100611EA 1ES66 IH5142MJE/883B M38510/10503BEA

3/ IH5142MJE

3/ HI1-5042/883

8100612EA 1ES66 IH5143MJE/883B M38510/10504BEA

3/ IH5143MJE

3/ HI1-5043/883

81006122A 34371 HI4-5043/883 ---

8100613EA 1ES66 IH5144MJE/883B M38510/10505BEA

3/ IH5144MJE

3/ HI1-5044/883

8100613IA 3/ DG5044AA M38510/10505BIA

8100614EA 1ES66 IH5145MJE/883B M38510/10506BEA

3/ IH5145MJE

3/ HI1-5045/883

81006142A 3/ HI4-5045/883 ---

8100615EA 3/ HI1-5046/883 M38510/10507BEA

8100616EA 1ES66 IH5047MJE/883B M38510/10508BEA

3/ HI1-5047/883

8100617EA 34371 HI1-5046A/883 ---

8100618EA 3/ HI1-5047A/883 ---

8100619EA 3/ IH5148MJE/883B ---

3/ HI1-5048/883

See footnotes at end of table.

2 of 3

STANDARD MICROCIRCUIT DRAWING BULLETIN – Continued.

Standard

microcircuit drawing

PIN 1/

Vendor

CAGE

number

Vendor

similar

PIN 2/

Reference military

specification

8100620EA 1ES66 IH5149MJE/883B ---

3/ HI1-5049/883

81006202A 3/ HI4-5049/883 ---

8100621EA 1ES66 IH5150MJE/883B ---

3/ HI1-5050/883

8100622EA 3/ IH5151MJE ---

3/ HI1-5051/883

1ES66 IH5151MJE/883B

81006222A 3/ HI4-5051/883 ---

1/ The lead finish shown for each PIN representing

a hermetic package is the most readily available

from the manufacturer listed for that part. If the

desired lead finish is not listed contact the vendor

to determine its availability.

2/ Caution. Do not use this number for item

acquisition. Items acquired to this number may not

satisfy the performance requirements of this drawing.

3/ Not available from an approved source of supply.

Vendor CAGE Vendor name

number and address

1ES66 Maxim Integrated Products

120 San Gabriel Drive

Sunnyvale, CA 94086

34371 Intersil Corporation

2401 Palm Bay Blvd

P.O. Box 883

Melbourne, FL 32902-0883

The information contained herein is disseminated for convenience only and the

Government assumes no liability whatsoever for any inaccuracies in the

information bulletin.

3 of 3