A M I C R O S E M I LX8817 Dual Channel 2.5A Low Dropout Regulator C O M P A N Y P RELIMINARY The LX8817 is a dual channel positive-voltage linear regulator. This dual regulator has one fixed output coupled with an adjustable output. Each channel features low-dropout and high accuracy. The LX8817 utilizes dual inputs that can be used as separate sources for the control and power sections. This configuration reduces power dissipation by operating the regulator near dropout (VPWR-VOUT = VDO = 0.6V @ 2.5A) while providing sufficient operating headroom for the control logic. The LX8817 provides designers with an efficient flexible power management solution, minimal printed circuit board area, and shorter design cycles. Each channel can supply up to 2.5A independently with a regulator design optimized for system efficiency by consuming minimal ground current and directing quiescent current to the load. The LX8817 features on-chip trimming of the internal voltage reference, enabling precise output voltages, typically 1% of it's specified value. Power sequencing logic ensures proper startup regardless of the level of VCTRL or VPWR. The LX8817 outputs remain off while VPWR < 2.7V. Thermal and Short Circuit Current Protection are integrated on-chip and operate independently for each regulator output. The LX8817 regulator is stable with a low-value output capacitor, typically 10F tantalum or ceramic on the outputs, allowing designers flexibility in external component selection. Linfinity's S-PAK power package offers maximum power dissipation and ease of assembly using surface mount technology. Two Independent Regulated Outputs Accurate Output Voltages Max. Dropout of 0.6V at Rated Current Independent Thermal and Current Limit Protection Low Profile 7 Lead SMT Power Package Low Tolerance Line (0.2%) and Load (0.4%) Regulation Wide DC Supply Voltage of 3.0V W W W . Microsemi . COM to 10.0V Loop Stability Independent of Output Capacitor Type 3.3V to 2.5V/ADJ Linear Regulator Low Voltage Logic Supplies Active SCSI Terminators Battery Charging Circuits Instrumentation PC Peripherals IMPORTANT: For the most current data, consult MICROSEMI's website: http://www.microsemi.com V PW R 3 2 5 LX 8817 V C TR L V1 1 V2 6 4 LX 8 8 1 7 TA (C) OUTPUT V1 OUTPUT V2 0 to 125 2.5V Adj DF Plastic S-PAK 7-PIN LX8817-2500CDF Note: Available in Tape & Reel. Append the letter "T" to the part number. (i.e. LX8817-xxxxC__T) Copyright 2000 Rev. 0.2a, 2000-09-15 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 1 A M I C R O S E M I LX8817 Dual Channel 2.5A Low Dropout Regulator C O M P A N Y P RELIMINARY Input Voltage (VCTRL, VPWR) ........................................................................ 13.5V Load Current (Internally Limited) .................................................................. 3.0A Power Dissipation...................................................................... Internally Limited Short-Circuit Protection...........................................................................Indefinite Operating Junction Temperature ..................................................................150C Storage Temperature Range .......................................................... -65C to 150C Lead Temperature (Soldering 180 seconds) .................................................235C W W W . Microsemi . COM T AB is G N D Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified terminal . 7 NC 6 A D J V2 5 V O UT2 4 GND 3 V PW R 2 V O UT1 1 V C TR L D F P A CK A G E (T op V iew) DF Plastic S-PAK 7-PIN THERMAL RESISTANCE-JUNCTION TO TAB, JT THERMAL RESISTANCE-JUNCTION TO AMBIENT, JA 4.5C/W 20C/W Junction Temperature Calculation: TJ = TA + (PD x JA). The JA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. JA can vary from 10C/W to > 30C/W depending on mounting technique. (See Application Notes Section: Thermal considerations) 1 VCTRL Unregulated input voltage supply, provides bias for control circuitry, (VCTRL - VOUT) > 1V. 2 VOUT1 Regulator #1 fixed output voltage. 3 VPWR Unregulated input voltage supply for power section. For proper operation: (VPWR - VOUT) > VDROPOUT. 4 GND Common terminal for ground reference, Tab of package is internally connected to this pin. 5 VOUT2 Regulator #2 adjustable output. 6 ADJV2 Regulator #2 voltage feedback. Sets the output voltage for regulator #2 via an external resistor divider. 7 NC Not used. PACKAGE DATA Copyright 2000 Rev. 0.2a, 2000-09-15 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 2 A M I C R O S E M I LX8817 Dual Channel 2.5A Low Dropout Regulator C O M P A N Y P RELIMINARY Unless otherwise specified, the following specifications apply over the operating ambient temperature 0C TA 135C except where otherwise noted and the following test conditions: VCTRL = 5V, VPWR = 3.3V IOUT = 10mA, C1, 2, 3, 4 = 10F (Tantalum), and TJ = TA using low duty cycling methods. Parameter Test Conditions LX8817-xx00 Min Typ Max Units FIXED OUTPUT Output Voltage * LX8815-2500 V1 Line Regulation Load Regulation V1(VIN) V1(I1) Dropout Voltage (PWR) VPWR-V1 Current Limit Minimum Load Current I1 (MAX) I1 I1 = 10mA, TJ = 25C 5mA < I1 < 2.5A, 3.75V < VCTRL < 8V 3V < VPWR < 5.5V 3.3V<VCTRL<10V, 3.3V<VPWR<5V, I1 = 5mA 5mA < I1 < 2.5A, VCTRL=5V, VPWR=3.3V I1 = 2.5A, V1 = -2% I1 = 2.0A, V1 = -2% I1 = 1.0A, V1 = -2% 2.475 2.500 2.550 2.425 2.500 1 1 0.500 0.375 0.225 3.0 0 2.570 5 9 0.630 0.530 0.350 1.225 1.250 1.275 1.213 1.250 0.05 1 0.500 0.375 0.225 3.0 1 1 1.288 3 7 0.63 0.53 0.35 2.55 Note 1 15 V mV mV V A mA ADJUSTABLE OUTPUT Reference Voltage V2 Line Regulation Load Regulation V2(VIN) V2(I2) Dropout Voltage VPWR-V2 Current Limit Minimum Load Current Adjust Pin Bias Current Symbol W W W . Microsemi . COM I2 (MAX) I2 IADJ I2 = 10mA, TJ = 25C 5mA < I2 < 2.5A, 3.0V < VCTRL < 8V 2V < VPWR < 5.5V 3V<VCTRL<10V, 2V<VPWR<5.5V, I2 = 5mA 5mA < I2 < 2.5A, VCTRL=5V, VPWR=3.3V I2 = 2.5A, V2 = -2% I2 = 2.0A, V2 = -2% I2 = 1.0A, V2 = -2% V 2.55 Note 1 25 5 mV mV V A mA A ENTIRE REGULATOR Under Voltage Lockout Quiescent Current Ripple Rejection RMS Output Noise Thermal Shutdown IQ PSRR VPWR Rising, 3.0V<VCTRL=10V, Both Outputs High Impedance VCTRL Rising, 3.0V<VPWR=10V, Both Outputs High Impedance I1=I2=10mA f=120Hz, TJ = 25C 10Hz < f < 10kHz 2.5 60 TJSD 1.8 75 0.003 160 2.5 10 V mA dB %VOUT C Copyright 2000 Rev. 0.2a, 2000-09-15 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 3 ELECTRICALS Note 1: Minimum load current is defined as the amount of output current required to maintain regulation. Typically this current provides the bias to the external resistor divider network used to set the output voltage. A M I C R O S E M I LX8817 Dual Channel 2.5A Low Dropout Regulator C O M P A N Y P RELIMINARY V PWR W W W . Microsemi . COM 3 C1 10 F + Input P ow er S equenc ing (U V LO ) V CTRL V1 2 - C3 10 F 1 C2 10 F 1.25V V REF B IA S VO U T 2 = 1 . 25 x 1 + + R1 + I AD J x R2 R2 V2 5 - (A dju stab le ) R1 C4 10 F 6 GND 4 R2 Dim A C I D B K H F G E INCHES MIN MAX .365 .375 .350 .360 .070 .080 .295 .305 .005 .015 .023 .033 0.050 BSC .031 .041 .170 .270 .001 .005 .410 .420 Note: 1. Dimensions do not include mold flash or protrusions; these shall not exceed 0.155mm(.006") on any side. Lead dimension shall not include solder coverage. Preliminary Data - Information contained in this document is pre-production data and is proprietary to LinFinity. It may not be modified in any way without the express written consent of LinFinity. Product referred to herein is offered in sample form only and LinFinity reserves the right to change or discontinue this proposed product at any time. Copyright 2000 Rev. 0.2a, 2000-09-15 Microsemi Linfinity Microelectronics Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 4 APPLICATIONS J A B C D E F G H I J K MILLIMETERS MIN MAX 9.27 9.52 8.89 9.14 1.77 2.03 7.49 7.74 0.12 0.38 0.58 0.84 1.27 BSC 0.79 1.04 4.31 6.86 0.03 0.13 10.41 10.67