MLG0402Q4N3ST - TDK Corporation

INDUCTORS

MLG0402Q 0402 [01005 inch]*

MLG0603P 0603 [0201 inch]

* Dimensions Code JIS[EIA]

July 2013

Inductors for High Frequency Circuits

Multilayer Ceramic

MLG-Q

MLG-P

series

(2/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

REMINDERS FOR USING THESE PRODUCTS

Before using these products, be sure to request the delivery specifications.

SAFETY REMINDERS

Please pay sufficient attention to the warnings for safe designing when using these products.

The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH

or less).

If the storage period elapses, the soldering of the terminal electrodes may deteriorate.

Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).

Before soldering, be sure to preheat components.

The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature

does not exceed 150°C.

Soldering corrections after mounting should be within the range of the conditions determined in the specifications.

If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.

When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to

the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.

Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal

design.

Carefully lay out the coil for the circuit board design of the non-magnetic shield type.

A malfunction may occur due to magnetic interference.

Use a wrist band to discharge static electricity in your body through the grounding wire.

Do not expose the products to magnets or magnetic fields.

Do not use for a purpose outside of the contents regulated in the delivery specifications.

The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications

equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement

equipment, industrial robots) under a normal operation and use condition.

The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or

quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to

society, person or property.

If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions

set forth in the each catalog, please contact us.

(1) Aerospace/Aviation equipment

(2) Transportation equipment (cars, electric trains, ships, etc.)

(3) Medical equipment

(4) Power-generation control equipment

(5) Atomic energy-related equipment

(6) Seabed equipment

(7) Transportation control equipment

(8) Public information-processing equipment

(9) Military equipment

(10) Electric heating apparatus, burning equipment

(11) Disaster prevention/crime prevention equipment

(12) Safety equipment

(13) Other applications that are not considered general-purpose

applications

When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing

protection circuit/device or providing backup circuits in your equipment.

REMINDERS

(3/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

Inductors for High Frequency Circuits

Multilayer Ceramic

FEATURES

High Q type inductor for high-frequency circuits.

The 0402 Series has0.2 to 33nH, and the 0603 Series has 0.6 to 120nH.

0.1n step inductance lineup.

Compared with existing products, the size was greatly reduced, making it optimal for fine-pitch circuits.

Optimal configuration that greatly improves the Q to 800MHz or higher.

Advanced monolithic structure is formed using a multilayering and sintering process with ceramic and conductive materials for High-

frequency.

APPLICATION

Smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners, automotive equipment

(MLG-P series) and other high frequency circuits for the mobile communication industry

PART NUMBER CONSTRUCTION

OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT

The Storage temperature range is for after the circuit board is mounted.

Product compatible with RoHS directive

Halogen-free

Compatible with lead-free solders

Overview of the MLG-Q, MLG-P Series

MLG 0402 Q 0N2 S T □□□

Series name L×W×H Dimensions Characteristics Inductance Inductance

tolerance Packaging style Internal code

(mm) (μH)

0402 0.4×0.2×0.2 P 1N1 1.1 B ±0.1nH T Taping

0603 0.6×0.3×0.3 Q 11N 11 C ±0.2nH

S ±0.3nH

H±3%

J±5%

Type

Temperature range

Package quantity Individual weight

Operating

temperature

Storage

temperature

（°C）（°C）(pieces/reel) （mg）

MLG0402Q –55 to +125 –55 to +125 20000 0.07

MLG0603P –55 to +125 –55 to +125 15000 0.2

RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/

Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.

(4/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

Overview of the MLG-Q, MLG-P Series

RECOMMENDED REFLOW PROFILE

Preheating Soldering Peak

Temp. Time Temp. Time Temp. Time

T1 T2 t1 T3 t2 T4 t3

150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.

Natural

cooling

Preheating

Soldering

T3 T3

t: Time

Peak

T: Temperature

(5/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

MLG-Qseries

MLG0402Q Type

SHAPE & DIMENSIONS

RECOMMENDED LAND PATTERN

Dimensions in mm

0.40±0.02

0.11±0.03 0.11±0.03

0.20±0.02 0.20±0.02

Dimensions in mm

0.18 to 0.20

0.15 to 0.2

0.2

0.15 to 0.2

(6/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

MLG-Qseries MLG0402Q Type

ELECTRICAL CHARACTERISTICS

CHARACTERISTICS SPECIFICATION TABLE

 The " △" of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).

Please contact us for information on inductance tolerance, G (±2%).

* The " □□□ " of the Part Number contains the internal code.

○Measurement equipment

＊ Equivalent measurement equipment may be used.

min.

L, Q measuring

frequency

(MHz)

Self-resonant

frequency

(GHz)

DC resistance

(:)

Rated current

(mA)

max.

Part No.

(nH) Tolerance min. typ. max. typ.

0.2 ±0.1, ±0.2nH — 100 10.0 20.0 0.10 0.03 350 MLG0402Q0N2△T□□□

0.3 ±0.1, ±0.2nH —100 10.0 18.5 0.20 0.07 350 MLG0402Q0N3△T□□□

0.4 ±0.1, ±0.2nH — 100 10.0 20.0 0.20 0.08 350 MLG0402Q0N4△T□□□

0.5 ±0.1, ±0.2nH —100 10.0 20.0 0.20 0.11 350 MLG0402Q0N5△T□□□

0.6 ±0.1, ±0.2nH — 100 10.0 20.0 0.30 0.13 320 MLG0402Q0N6△T□□□

0.7 ±0.1, ±0.2nH —100 10.0 20.0 0.40 0.19 320 MLG0402Q0N7△T□□□

0.8 ±0.1, ±0.2nH — 100 10.0 19.5 0.40 0.11 320 MLG0402Q0N8△T□□□

0.9 ±0.1, ±0.2nH —100 10.0 20.0 0.40 0.15 320 MLG0402Q0N9△T□□□

1.0 ±0.1,±0.2, ±0.3nH 2 100 10.0 16.8 0.40 0.20 250 MLG0402Q1N0△T□□□

1.1 ±0.1,±0.2, ±0.3nH 2100 10.0 16.6 0.50 0.22 250 MLG0402Q1N1△T□□□

1.2 ±0.1,±0.2, ±0.3nH 2 100 10.0 16.2 0.50 0.25 250 MLG0402Q1N2△T□□□

1.3 ±0.1,±0.2, ±0.3nH 2100 10.0 16.0 0.60 0.28 250 MLG0402Q1N3△T□□□

1.4 ±0.1,±0.2, ±0.3nH 2 100 10.0 15.8 0.60 0.30 250 MLG0402Q1N4△T□□□

1.5 ±0.1,±0.2, ±0.3nH 2100 10.0 15.6 0.60 0.37 220 MLG0402Q1N5△T□□□

1.6 ±0.1,±0.2, ±0.3nH 2 100 10.0 14.4 0.60 0.25 220 MLG0402Q1N6△T□□□

1.7 ±0.1,±0.2, ±0.3nH 2100 10.0 13.4 0.60 0.25 200 MLG0402Q1N7△T□□□

1.8 ±0.1,±0.2, ±0.3nH 2 100 10.0 13.9 0.60 0.28 200 MLG0402Q1N8△T□□□

1.9 ±0.1,±0.2, ±0.3nH 2100 9.0 12.2 0.60 0.27 200 MLG0402Q1N9△T□□□

2.0 ±0.1,±0.2, ±0.3nH 2 100 9.0 12.5 0.60 0.30 200 MLG0402Q2N0△T□□□

2.1 ±0.1,±0.2, ±0.3nH 2100 8.0 11.8 0.70 0.36 200 MLG0402Q2N1△T□□□

2.2 ±0.1,±0.2, ±0.3nH 2 100 8.0 11.7 0.80 0.43 200 MLG0402Q2N2△T□□□

2.3 ±0.1,±0.2, ±0.3nH 2100 7.0 11.0 0.80 0.46 200 MLG0402Q2N3△T□□□

2.4 ±0.1,±0.2, ±0.3nH 2 100 7.0 10.9 0.80 0.43 200 MLG0402Q2N4△T□□□

2.5 ±0.1,±0.2, ±0.3nH 2100 7.0 10.5 0.80 0.54 200 MLG0402Q2N5△T□□□

2.6 ±0.1,±0.2, ±0.3nH 2 100 7.0 10.7 0.80 0.54 200 MLG0402Q2N6△T□□□

2.7 ±0.1,±0.2, ±0.3nH 2100 7.0 10.7 0.80 0.54 200 MLG0402Q2N7△T□□□

2.8 ±0.1,±0.2, ±0.3nH 2 100 7.0 10.4 0.80 0.56 200 MLG0402Q2N8△T□□□

2.9 ±0.1,±0.2, ±0.3nH 2100 7.0 10.0 0.80 0.52 200 MLG0402Q2N9△T□□□

3.0 ±0.1,±0.2, ±0.3nH 2 100 7.0 10.0 0.80 0.45 200 MLG0402Q3N0△T□□□

3.1 ±0.1,±0.2, ±0.3nH 2100 7.0 9.7 0.90 0.58 200 MLG0402Q3N1△T□□□

3.2 ±0.1,±0.2, ±0.3nH 2 100 7.0 9.4 1.00 0.66 200 MLG0402Q3N2△T□□□

3.3 ±0.1,±0.2, ±0.3nH 2100 7.0 10.0 1.10 0.73 180 MLG0402Q3N3△T□□□

3.4 ±0.1,±0.2, ±0.3nH 2 100 6.5 9.1 1.10 0.73 180 MLG0402Q3N4△T□□□

3.5 ±0.1,±0.2, ±0.3nH 2100 6.0 9.0 1.10 0.74 180 MLG0402Q3N5△T□□□

3.6 ±0.1,±0.2, ±0.3nH 2 100 6.0 9.0 1.10 0.75 180 MLG0402Q3N6△T□□□

3.7 ±0.1,±0.2, ±0.3nH 2100 6.0 8.9 1.10 0.73 180 MLG0402Q3N7△T□□□

3.8 ±0.1,±0.2, ±0.3nH 2 100 6.0 8.4 1.10 0.70 180 MLG0402Q3N8△T□□□

3.9 ±0.1,±0.2, ±0.3nH 2100 6.0 8.8 1.20 0.77 180 MLG0402Q3N9△T□□□

4.0 ±0.1,±0.2, ±0.3nH 2 100 6.0 8.4 1.20 0.71 180 MLG0402Q4N0△T□□□

4.3 ±3%, ±0.3nH 2100 6.0 8.6 1.20 0.77 180 MLG0402Q4N3△T□□□

4.7 ±3%, ±0.3nH 2 100 6.0 8.1 1.30 0.88 160 MLG0402Q4N7△T□□□

5.1 ±3%, ±0.3nH 2100 6.0 7.8 1.40 0.90 160 MLG0402Q5N1△T□□□

5.6 ±3%, ±0.3nH 2 100 6.0 7.8 1.50 1.02 140 MLG0402Q5N6△T□□□

6.2 ±3%, ±0.3nH 2100 5.5 7.2 1.50 1.04 140 MLG0402Q6N2△T□□□

6.8 ±3%, ±5% 2 100 5.5 6.9 1.60 1.12 140 MLG0402Q6N8△T□□□

7.5 ±3%, ±5% 2100 5.0 6.7 1.70 1.13 140 MLG0402Q7N5△T□□□

8.2 ±3%, ±5% 2 100 4.5 6.2 1.80 1.16 140 MLG0402Q8N2△T□□□

9.1 ±3%, ±5% 2100 4.0 5.7 1.80 1.20 140 MLG0402Q9N1△T□□□

10 ±3%, ±5% 3 100 4.0 5.3 2.10 1.45 140 MLG0402Q10N△T□□□

12 ±3%, ±5% 3100 3.5 4.8 2.40 1.64 140 MLG0402Q12N△T□□□

15 ±3%, ±5% 3 100 3.0 4.5 2.60 1.77 140 MLG0402Q15N△T□□□

18 ±3%, ±5% 3100 2.5 3.0 2.80 1.94 140 MLG0402Q18N△T□□□

22 ±3%, ±5% 3 100 2.2 2.7 3.20 2.18 130 MLG0402Q22N△T□□□

27 ±3%, ±5% 3100 1.9 2.5 3.50 2.44 120 MLG0402Q27N△T□□□

33 ±3%, ±5% 3 100 1.7 2.2 3.80 2.71 120 MLG0402Q33N△T□□□

Measurement item Product No. Manufacturer

L, Q 4291B+16196D Agilent Technologies

Self-resonant frequency 8720C Agilent Technologies

DC resistance 4338A Agilent Technologies

(7/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

MLG-Qseries MLG0402Q Type

ELECTRICAL CHARACTERISTICS

L, Q FREQUENCY CHARACTERISTICS TABLE

The " △" of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).

Please contact us for information on inductance tolerance, G (±2%).

 The " □□□ " of the Part Number contains the internal code.

○Measurement equipment

＊ Equivalent measurement equipment may be used.

L(nH)typ. Q typ. Part No.*

500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz

0.2 0.2 0.2 0.2 0.2 8 11 18 20 23 MLG0402Q0N2△T□□□

0.3 0.3 0.3 0.3 0.3 7 9 15 16 19 MLG0402Q0N3△T□□□

0.4 0.4 0.4 0.4 0.3 9 12 19 20 22 MLG0402Q0N4△T□□□

0.5 0.5 0.4 0.4 0.4 912 19 21 23 MLG0402Q0N5△T□□□

0.6 0.5 0.5 0.5 0.5 7 11 17 18 20 MLG0402Q0N6△T□□□

0.7 0.7 0.6 0.6 0.6 811 18 19 22 MLG0402Q0N7△T□□□

0.7 0.7 0.7 0.7 0.7 9 12 20 21 24 MLG0402Q0N8△T□□□

0.8 0.8 0.8 0.8 0.8 10 13 21 23 26 MLG0402Q0N9△T□□□

0.9 0.9 0.9 0.9 0.9 10 12 20 22 25 MLG0402Q1N0△T□□□

1.0 1.0 1.0 1.0 1.0 912 20 22 25 MLG0402Q1N1△T□□□

1.1 1.1 1.1 1.1 1.1 9 12 20 21 24 MLG0402Q1N2△T□□□

1.2 1.2 1.2 1.2 1.2 912 20 22 25 MLG0402Q1N3△T□□□

1.3 1.3 1.3 1.3 1.3 9 12 20 22 25 MLG0402Q1N4△T□□□

1.4 1.4 1.4 1.4 1.4 912 19 21 23 MLG0402Q1N5△T□□□

1.5 1.5 1.4 1.4 1.4 10 13 22 23 26 MLG0402Q1N6△T□□□

1.6 1.5 1.5 1.5 1.5 10 13 21 23 25 MLG0402Q1N7△T□□□

1.7 1.6 1.6 1.6 1.6 11 14 22 24 27 MLG0402Q1N8△T□□□

1.8 1.8 1.7 1.7 1.7 10 14 22 24 27 MLG0402Q1N9△T□□□

1.9 1.8 1.8 1.8 1.8 10 13 21 23 26 MLG0402Q2N0△T□□□

2.0 2.0 1.9 1.9 1.9 10 14 22 24 27 MLG0402Q2N1△T□□□

2.1 2.1 2.0 2.0 2.0 10 14 22 24 27 MLG0402Q2N2△T□□□

2.2 2.2 2.1 2.1 2.2 10 13 21 23 25 MLG0402Q2N3△T□□□

2.3 2.3 2.2 2.2 2.2 9 13 21 22 25 MLG0402Q2N4△T□□□

2.4 2.4 2.3 2.3 2.4 10 13 21 22 25 MLG0402Q2N5△T□□□

2.5 2.5 2.4 2.4 2.4 10 13 20 22 24 MLG0402Q2N6△T□□□

2.5 2.5 2.5 2.5 2.5 10 13 21 23 25 MLG0402Q2N7△T□□□

2.6 2.6 2.6 2.6 2.6 10 13 20 22 24 MLG0402Q2N8△T□□□

2.7 2.7 2.7 2.7 2.7 10 13 20 21 23 MLG0402Q2N9△T□□□

2.8 2.8 2.7 2.7 2.8 10 13 20 21 23 MLG0402Q3N0△T□□□

2.9 2.9 2.9 2.9 2.9 912 19 21 23 MLG0402Q3N1△T□□□

3.0 3.0 3.0 3.0 3.0 9 12 19 20 22 MLG0402Q3N2△T□□□

3.2 3.1 3.1 3.1 3.1 912 19 21 23 MLG0402Q3N3△T□□□

3.2 3.2 3.2 3.2 3.2 9 12 19 20 22 MLG0402Q3N4△T□□□

3.3 3.3 3.3 3.3 3.3 912 19 20 22 MLG0402Q3N5△T□□□

3.4 3.4 3.4 3.4 3.4 10 13 20 22 24 MLG0402Q3N6△T□□□

3.5 3.5 3.4 3.5 3.5 912 19 21 23 MLG0402Q3N7△T□□□

3.6 3.6 3.5 3.6 3.6 10 13 19 21 23 MLG0402Q3N8△T□□□

3.7 3.7 3.7 3.7 3.7 912 19 20 22 MLG0402Q3N9△T□□□

3.8 3.8 3.7 3.8 3.8 9 12 19 20 22 MLG0402Q4N0△T□□□

4.1 4.0 4.0 4.0 4.1 10 13 21 23 25 MLG0402Q4N3△T□□□

4.5 4.5 4.5 4.5 4.6 10 13 21 23 25 MLG0402Q4N7△T□□□

4.8 4.8 4.8 4.8 4.9 10 13 20 22 24 MLG0402Q5N1△T□□□

5.3 5.3 5.3 5.3 5.4 11 14 22 23 25 MLG0402Q5N6△T□□□

5.9 5.8 5.9 5.9 6.0 11 14 21 23 25 MLG0402Q6N2△T□□□

6.5 6.4 6.5 6.6 6.7 10 13 21 22 23 MLG0402Q6N8△T□□□

7.1 7.0 7.1 7.2 7.4 11 14 22 23 25 MLG0402Q7N5△T□□□

7.8 7.8 7.9 8.0 8.3 11 14 21 23 24 MLG0402Q8N2△T□□□

8.6 8.5 8.7 8.8 9.1 11 14 21 23 24 MLG0402Q9N1△T□□□

9.5 9.5 9.8 9.9 10.3 11 14 21 22 23 MLG0402Q10N△T□□□

11.4 11.4 11.9 12.2 12.8 11 13 20 21 21 MLG0402Q12N△T□□□

14.1 14.0 14.8 15.2 16.2 11 14 20 21 21 MLG0402Q15N△T□□□

17.0 17.2 21.3 23.3 29.2 11 13 16 16 13 MLG0402Q18N△T□□□

20.7 21.1 28.1 32.0 45.2 10 12 13 12 9 MLG0402Q22N△T□□□

25.3 25.7 34.1 38.9 10 12 12 11 MLG0402Q27N△T□□□

31.0 32.2 52.2 10 12 10 MLG0402Q33N△T□□□

Product No. Manufacturer

4291B+16196D Agilent Technologies

(8/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

MLG-Qseries MLG0402Q Type

ELECTRICAL CHARACTERISTICS

L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)

○Measurement equipment

＊ Equivalent measurement equipment may be used.

10 100 1000 10000

1000

100

Frequency(MHz)

Inductance(nH)

33N

27N

22N

18N

15N

12N

10N

8N2

6N8

5N6

4N7

3N9

3N3

2N7

2N2

1N8

1N5

1N2

1N0

Product No. Manufacturer

E4991A+16196D Agilent Technologies

(9/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

MLG-Qseries MLG0402Q Type

ELECTRICAL CHARACTERISTICS

Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)

○Measurement equipment

＊ Equivalent measurement equipment may be used.

10 100 1000 10000

Frequency(MHz)

33N 27N

22N

18N

15N

12N

6N8

5N6

3N9

3N3

2N7

2N2

1N8

1N5

1N0

1N2

4N7

8N2

10N

Product No. Manufacturer

E4991A+16196D Agilent Technologies

(10/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

MLG-Pseries

MLG0603P Type

SHAPE & DIMENSIONS

RECOMMENDED LAND PATTERN

Dimensions in mm

0.15±0.050.15±0.05

0.60±0.03

0.09±0.04 0.09±0.04

0.30±0.030.30±0.03

Dimensions in mm

0.3

0.3 0.250.25

(11/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

MLG-Pseries MLG0603P Type

ELECTRICAL CHARACTERISTICS

CHARACTERISTICS SPECIFICATION TABLE

 The " △" of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).

Please contact us for information on inductance tolerance, G (±2%).

* The " □□□ " of the Part Number contains the internal code.

○Short bar residual inductance =0.43nH

○Measurement equipment

＊ Equivalent measurement equipment may be used.

min.

L, Q measuring

frequency

(MHz)

Self-resonant

frequency

(GHz)

DC resistance

(:)

Rated current

(mA)

max.

Part No.

(nH) Tolerance min. typ. max. typ.

0.6 ±0.1, ±0.2nH — 500 10.0 20.0 0.06 0.01 1000 MLG0603P0N6△T□□□

0.7 ±0.1, ±0.2nH —500 10.0 20.0 0.06 0.01 1000 MLG0603P0N7△T□□□

0.8 ±0.1, ±0.2nH — 500 10.0 20.0 0.06 0.02 1000 MLG0603P0N8△T□□□

0.9 ±0.1, ±0.2nH —500 10.0 20.0 0.06 0.02 1000 MLG0603P0N9△T□□□

1.0 ±0.1, ±0.2, 0.3nH 14 500 10.0 20.0 0.07 0.02 1000 MLG0603P1N0△T□□□

1.1 ±0.1, ±0.2, 0.3nH 14 500 10.0 19.9 0.07 0.03 1000 MLG0603P1N1△T□□□

1.2 ±0.1, ±0.2, 0.3nH 14 500 10.0 16.0 0.08 0.04 800 MLG0603P1N2△T□□□

1.3 ±0.1, ±0.2, 0.3nH 14 500 10.0 13.9 0.08 0.03 800 MLG0603P1N3△T□□□

1.4 ±0.1, ±0.2, 0.3nH 14 500 10.0 11.7 0.09 0.04 800 MLG0603P1N4△T□□□

1.5 ±0.1, ±0.2, 0.3nH 14 500 10.0 14.9 0.10 0.03 800 MLG0603P1N5△T□□□

1.6 ±0.1, ±0.2, 0.3nH 14 500 10.0 13.4 0.10 0.03 700 MLG0603P1N6△T□□□

1.7 ±0.1, ±0.2, 0.3nH 14 500 10.0 12.8 0.10 0.02 700 MLG0603P1N7△T□□□

1.8 ±0.1, ±0.2, 0.3nH 14 500 9.0 10.7 0.10 0.03 700 MLG0603P1N8△T□□□

1.9 ±0.1, ±0.2, 0.3nH 14 500 9.0 10.9 0.10 0.04 600 MLG0603P1N9△T□□□

2.0 ±0.1, ±0.2, 0.3nH 14 500 8.5 10.1 0.10 0.03 600 MLG0603P2N0△T□□□

2.1 ±0.1, ±0.2, 0.3nH 14 500 8.0 9.8 0.10 0.05 600 MLG0603P2N1△T□□□

2.2 ±0.1, ±0.2, 0.3nH 14 500 7.5 9.0 0.10 0.07 600 MLG0603P2N2△T□□□

2.3 ±0.1, ±0.2, 0.3nH 14 500 7.5 8.4 0.20 0.07 600 MLG0603P2N3△T□□□

2.4 ±0.1, ±0.2, 0.3nH 14 500 7.5 10.9 0.20 0.12 500 MLG0603P2N4△T□□□

2.5 ±0.1, ±0.2, 0.3nH 14 500 7.5 9.9 0.20 0.09 500 MLG0603P2N5△T□□□

2.6 ±0.1, ±0.2, 0.3nH 14 500 7.5 10.1 0.20 0.14 500 MLG0603P2N6△T□□□

2.7 ±0.1, ±0.2, 0.3nH 14 500 7.5 10.0 0.20 0.14 500 MLG0603P2N7△T□□□

2.8 ±0.1, ±0.2, 0.3nH 14 500 7.5 9.9 0.20 0.10 500 MLG0603P2N8△T□□□

2.9 ±0.1, ±0.2, 0.3nH 14 500 7.5 9.2 0.20 0.10 500 MLG0603P2N9△T□□□

3.0 ±0.1, ±0.2, 0.3nH 14 500 7.5 9.1 0.20 0.14 450 MLG0603P3N0△T□□□

3.1 ±0.1, ±0.2, 0.3nH 14 500 7.5 8.8 0.20 0.10 450 MLG0603P3N1△T□□□

3.2 ±0.1, ±0.2, 0.3nH 14 500 7.5 8.4 0.20 0.14 450 MLG0603P3N2△T□□□

3.3 ±0.1, ±0.2, 0.3nH 14 500 7.5 8.4 0.20 0.13 450 MLG0603P3N3△T□□□

3.4 ±0.1, ±0.2, 0.3nH 14 500 7.0 8.1 0.20 0.13 450 MLG0603P3N4△T□□□

3.5 ±0.1, ±0.2, 0.3nH 14 500 6.5 8.0 0.20 0.12 450 MLG0603P3N5△T□□□

3.6 ±0.1, ±0.2, 0.3nH 14 500 6.5 7.7 0.20 0.10 400 MLG0603P3N6△T□□□

3.7 ±0.1, ±0.2, 0.3nH 14 500 6.5 7.4 0.20 0.14 400 MLG0603P3N7△T□□□

3.8 ±0.1, ±0.2, 0.3nH 14 500 5.8 7.0 0.30 0.24 400 MLG0603P3N8△T□□□

3.9 ±0.1, ±0.2, 0.3nH 14 500 5.8 7.1 0.30 0.22 400 MLG0603P3N9△T□□□

4.0 ±0.1, ±0.2, 0.3nH 14 500 5.8 6.7 0.40 0.21 350 MLG0603P4N0△T□□□

4.1 ±0.1, ±0.2, 0.3nH 14 500 5.8 6.7 0.40 0.29 350 MLG0603P4N1△T□□□

4.2 ±0.1, ±0.2, 0.3nH 14 500 5.8 6.6 0.40 0.24 350 MLG0603P4N2△T□□□

4.3 ±3%, ±5%, ±0.3nH 14 500 5.8 6.7 0.40 0.24 350 MLG0603P4N3△T□□□

4.7 ±3%, ±5%, ±0.3nH 14 500 5.5 6.9 0.40 0.16 350 MLG0603P4N7△T□□□

5.1 ±3%, ±5%, ±0.3nH 14 500 5.5 6.6 0.40 0.30 350 MLG0603P5N1△T□□□

5.6 ±3%, ±5%, ±0.3nH 14 500 4.0 5.3 0.40 0.32 350 MLG0603P5N6△T□□□

6.2 ±3%, ±5%, ±0.3nH 14 500 4.0 6.3 0.70 0.59 300 MLG0603P6N2△T□□□

6.8 ±3%, ±5% 14 500 4.0 6.1 0.75 0.62 300 MLG0603P6N8△T□□□

7.5 ±3%, ±5% 14 500 4.0 5.4 0.80 0.70 300 MLG0603P7N5△T□□□

8.2 ±3%, ±5% 14 500 4.0 5.2 0.85 0.71 250 MLG0603P8N2△T□□□

9.1 ±3%, ±5% 14 500 4.0 5.0 0.90 0.76 250 MLG0603P9N1△T□□□

Measurement item Product No. Manufacturer

L, Q 4291B+16197A Agilent Technologies

Self-resonant frequency 8720C Agilent Technologies

DC resistance Type-7561 Yokogawa

(12/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

MLG-Pseries MLG0603P Type

ELECTRICAL CHARACTERISTICS

CHARACTERISTICS SPECIFICATION TABLE

 The " △" of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).

Please contact us for information on inductance tolerance, G (±2%).

* The " □□□ " of the Part Number contains the internal code.

○Short bar residual inductance =0.43nH

○Measurement equipment

＊ Equivalent measurement equipment may be used.

min.

L, Q measuring

frequency

(MHz)

Self-resonant

frequency

(GHz)

DC resistance

(:)

Rated current

(mA)

max.

Part No.

(nH) tolerance min. typ. max. typ.

10 ±3%, ±5% 14 500 4.0 4.7 0.95 0.85 250 MLG0603P10N△T□□□

11 ±3%, ±5% 14 500 3.5 4.5 1.00 0.64 250 MLG0603P11N△T□□□

12 ±3%, ±5% 14 500 3.5 4.3 1.10 0.82 250 MLG0603P12N△T□□□

13 ±3%, ±5% 14 500 3.2 4.2 1.10 0.87 250 MLG0603P13N△T□□□

15 ±3%, ±5% 14 500 3.2 3.7 1.20 0.94 250 MLG0603P15N△T□□□

16 ±3%, ±5% 14 500 3.0 3.6 1.20 1.00 200 MLG0603P16N△T□□□

18 ±3%, ±5% 14 500 3.0 3.5 1.40 1.04 200 MLG0603P18N△T□□□

20 ±3%, ±5% 14 500 2.2 3.3 1.90 1.33 150 MLG0603P20N△T□□□

22 ±3%, ±5% 14 500 2.2 2.9 1.90 1.31 150 MLG0603P22N△T□□□

24 ±3%, ±5% 14 500 2.2 2.9 2.10 1.17 140 MLG0603P24N△T□□□

27 ±3%, ±5% 14 500 2.2 2.7 2.10 1.45 140 MLG0603P27N△T□□□

30 ±3%, ±5% 10 300 1.8 2.3 2.20 1.37 130 MLG0603P30N△T□□□

33 ±3%, ±5% 10 300 1.8 2.4 2.20 1.55 130 MLG0603P33N△T□□□

36 ±3%, ±5% 10 300 1.8 2.2 2.40 1.49 120 MLG0603P36N△T□□□

39 ±3%, ±5% 10 300 1.8 2.2 2.40 1.72 120 MLG0603P39N△T□□□

43 ±3%, ±5% 10 300 1.6 2.0 2.90 1.61 110 MLG0603P43N△T□□□

47 ±3%, ±5% 10 300 1.6 2.0 2.90 2.18 110 MLG0603P47N△T□□□

51 ±3%, ±5% 10 300 1.4 1.9 3.50 1.87 100 MLG0603P51N△T□□□

56 ±3%, ±5% 10 300 1.4 1.8 3.50 2.35 100 MLG0603P56N△T□□□

62 ±3%, ±5% 10 300 1.2 1.6 3.50 2.12 100 MLG0603P62N△T□□□

68 ±3%, ±5% 9 300 1.2 1.6 3.50 2.69 100 MLG0603P68N△T□□□

75 ±3%, ±5% 9300 1.0 1.5 4.00 2.59 80 MLG0603P75N△T□□□

82 ±3%, ±5% 9 300 1.0 1.5 4.00 2.71 80 MLG0603P82N△T□□□

91 ±3%, ±5% 9300 0.9 1.3 4.50 2.92 80 MLG0603P91N△T□□□

100 ±3%, ±5% 9 300 0.9 1.3 4.50 3.20 80 MLG0603PR10△T□□□

110 ±3%, ±5% 9300 0.8 1.1 5.00 3.50 80 MLG0603PR11△T□□□

120 ±3%, ±5% 9 300 0.8 1.0 5.00 3.79 80 MLG0603PR12△T□□□

Measurement item Product No. Manufacturer

L, Q 4291B+16197A Agilent Technologies

Self-resonant frequency 8720C Agilent Technologies

DC resistance Type-7561 Yokogawa

(13/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

MLG-Pseries MLG0603P Type

ELECTRICAL CHARACTERISTICS

L, Q FREQUENCY CHARACTERISTICS TABLE

The " △" of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).

Please contact us for information on inductance tolerance, G (±2%).

* The " □□□ " of the Part Number contains the internal code.

○Measurement equipment

＊ Equivalent measurement equipment may be used.

L(nH)typ. Q typ. Part No.

500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz

0.6 0.6 0.6 0.6 0.6 16min. 22min. 35min. 37min. 41min. MLG0603P0N6△T□□□

0.7 0.7 0.7 0.7 0.7 16min. 22min. 35min. 37min. 41min. MLG0603P0N7△T□□□

0.8 0.8 0.8 0.8 0.4 16 22 35 37 41 MLG0603P0N8△T□□□

0.9 0.9 0.9 0.9 0.9 17 22 35 37 41 MLG0603P0N9△T□□□

1.0 1.0 1.0 1.0 1.0 16 21 33 36 40 MLG0603P1N0△T□□□

1.1 1.1 1.1 1.1 1.1 17 23 36 38 43 MLG0603P1N1△T□□□

1.2 1.2 1.2 1.2 1.2 18 24 38 40 45 MLG0603P1N2△T□□□

1.3 1.3 1.3 1.3 1.3 17 22 34 36 40 MLG0603P1N3△T□□□

1.4 1.4 1.4 1.4 1.4 18 23 36 39 43 MLG0603P1N4△T□□□

1.5 1.5 1.5 1.5 1.5 17 22 33 35 39 MLG0603P1N5△T□□□

1.6 1.6 1.6 1.6 1.6 17 22 33 35 38 MLG0603P1N6△T□□□

1.7 1.7 1.7 1.7 1.7 17 22 33 35 39 MLG0603P1N7△T□□□

1.8 1.8 1.8 1.8 1.8 17 22 34 35 39 MLG0603P1N8△T□□□

1.9 1.9 1.9 1.9 1.9 18 24 36 38 42 MLG0603P1N9△T□□□

2.0 2.0 2.0 2.0 2.0 19 23 35 37 41 MLG0603P2N0△T□□□

2.1 2.1 2.1 2.1 2.1 18 23 34 36 39 MLG0603P2N1△T□□□

2.2 2.2 2.2 2.2 2.3 18 23 35 36 40 MLG0603P2N2△T□□□

2.3 2.3 2.3 2.4 2.4 18 22 33 35 38 MLG0603P2N3△T□□□

2.4 2.4 2.4 2.4 2.4 16 21 31 33 36 MLG0603P2N4△T□□□

2.5 2.5 2.5 2.5 2.5 17 22 33 34 38 MLG0603P2N5△T□□□

2.6 2.6 2.6 2.6 2.6 17 22 33 35 38 MLG0603P2N6△T□□□

2.7 2.7 2.7 2.7 2.7 17 21 33 35 38 MLG0603P2N7△T□□□

2.8 2.8 2.8 2.8 2.9 17 22 34 36 40 MLG0603P2N8△T□□□

2.9 2.9 2.9 2.9 3.0 17 22 34 35 39 MLG0603P2N9△T□□□

3.0 3.0 3.0 3.1 3.1 17 21 32 34 37 MLG0603P3N0△T□□□

3.1 3.1 3.1 3.2 3.2 17 22 33 34 37 MLG0603P3N1△T□□□

3.2 3.2 3.2 3.3 3.3 17 22 34 35 38 MLG0603P3N2△T□□□

3.3 3.3 3.4 3.4 3.4 18 22 33 35 38 MLG0603P3N3△T□□□

3.4 3.4 3.5 3.5 3.6 18 23 34 35 38 MLG0603P3N4△T□□□

3.5 3.5 3.6 3.6 3.7 18 23 34 35 38 MLG0603P3N5△T□□□

3.6 3.6 3.7 3.7 3.8 18 22 33 34 37 MLG0603P3N6△T□□□

3.7 3.7 3.8 3.9 4.0 18 23 34 35 37 MLG0603P3N7△T□□□

3.8 3.8 3.9 4.0 4.1 17 22 32 33 36 MLG0603P3N8△T□□□

3.9 3.9 4.0 4.1 4.2 17 22 32 34 36 MLG0603P3N9△T□□□

4.0 4.0 4.1 4.2 4.4

18 22 32 33 36 MLG0603P4N0△T□□□

4.1 4.1 4.3 4.3 4.5

18 22 33 34 36 MLG0603P4N1△T□□□

4.2 4.2 4.4 4.5 4.6

18 22 32 33 35 MLG0603P4N2△T□□□

4.3 4.3 4.5 4.5 4.7 17 21 32 33 35 MLG0603P4N3△T□□□

4.7 4.7 4.9 5.0 5.1 16 21 31 32 34 MLG0603P4N7△T□□□

5.1 5.1 5.3 5.4 5.7 16 21 31 32 34 MLG0603P5N1△T□□□

5.6 5.6 6.1 6.2 6.6 18 22 31 32 32 MLG0603P5N6△T□□□

6.2 6.2 6.5 6.7 7.0 16 21 30 31 33 MLG0603P6N2△T□□□

6.8 6.8 7.3 7.5 8.0 16 21 29 30 31 MLG0603P6N8△T□□□

7.5 7.5 8.1 8.3 8.8 16 21 30 30 32 MLG0603P7N5△T□□□

8.2 8.2 9.0 9.3 10.0 17 21 30 30 31 MLG0603P8N2△T□□□

9.1 9.1 10.0 10.3 11.1 17 21 30 31 32 MLG0603P9N1△T□□□

Product No. Manufacturer

4291B+16197A Agilent Technologies

(14/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

MLG-Pseries MLG0603P Type

ELECTRICAL CHARACTERISTICS

L, Q FREQUENCY CHARACTERISTICS TABLE

The " △" of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).

Please contact us for information on inductance tolerance, G (±2%).

* The " □□□ " of the Part Number contains the internal code.

○Measurement equipment

＊ Equivalent measurement equipment may be used.

L(nH)typ. Q typ. Part No.

500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz

10 10 11 12 13 16 21 28 28 28 MLG0603P10N△T□□□

11 11 13 13 15

18 23 30 30 30 MLG0603P11N△T□□□

12 12 14 15 17 18 22 28 28 27 MLG0603P12N△T□□□

13 13 15 16 19

18 22 28 28 26 MLG0603P13N△T□□□

15 15 18 20 24 18 22 27 26 24 MLG0603P15N△T□□□

16 16 20 22 27

18 22 26 25 22 MLG0603P16N△T□□□

18 18 23 26 33 18 22 25 24 20 MLG0603P18N△T□□□

20 21 27 31 42

18 22 23 22 17 MLG0603P20N△T□□□

22 23 34 40 68 18 21 21 18 11 MLG0603P22N△T□□□

24 25 36 43 72

19 22 21 18 11 MLG0603P24N△T□□□

27 28 45 57 18 21 18 15 MLG0603P27N△T□□□

30 32 59

18 21 15 MLG0603P30N△T□□□

33 36 68 15 17 11 MLG0603P33N△T□□□

37 39

16 17 MLG0603P36N△T□□□

40 43 15 17 MLG0603P39N△T□□□

44 48

15 16 MLG0603P43N△T□□□

48 53 15 16 MLG0603P47N△T□□□

53 59

15 16 MLG0603P51N△T□□□

58 66 15 15 MLG0603P56N△T□□□

65 76

15 15 MLG0603P62N△T□□□

71 82 15 15 MLG0603P68N△T□□□

79 97

14 13 MLG0603P75N△T□□□

87 109 14 13 MLG0603P82N△T□□□

99 132

13 12 MLG0603P91N△T□□□

110 152 14 12 MLG0603PR10△T□□□

126 211

13 9 MLG0603PR11△T□□□

151 12 MLG0603PR12△T□□□

Product No. Manufacturer

4291B+16197A Agilent Technologies

(15/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

MLG-Pseries MLG0603P Type

ELECTRICAL CHARACTERISTICS

L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)

○Measurement equipment

＊ Equivalent measurement equipment may be used.

10 100 1000 10000

1000

100

Frequency(MHz)

Inductance(nH)

R12

R10

82N 68N

56N

47N39N

33N 27N

22N

18N

15N

12N

10N

8N2

6N8

5N6

4N7

3N9

3N3

2N7

2N2

1N8

1N5

1N2

1N0

Product No. Manufacturer

E4991A+16197A Agilent Technologies

(16/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

MLG-Pseries MLG0603P Type

ELECTRICAL CHARACTERISTICS

Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)

○Measurement equipment

＊ Equivalent measurement equipment may be used.

10 100 1000 10000

Frequency(MHz)

R12 R10

27N

22N

18N

15N

12N

10N

8N2

6N8

5N6

4N7

3N9

3N3

2N7

1N8

1N2

1N0

39N

56N

47N

68N

82N

33N

1N5

2N2

Product No. Manufacturer

E4991A+16197A Agilent Technologies

(17/17)

INDUCTORS

001-01 / 20130717 / inductor_high-frequency_mlg-qp_en.fm

• All specifications are subject to change without notice.

MLG-Q, MLG-Pseries

Packaging Style

REEL DIMENSIONS

TAPE DIMENSIONS

1.0

ø180±2.0

2.0±0.5

ø13±0.2

ø21±0.8

ø60min.

14.4max.

Dimensions in mm

8.4 +2.0

–0.0

8.0±0.3 3.5±0.05

1.75±0.1

4.0±0.1

1.5 +0.1

–0.0

Sprocket hole Cavity

A B

2.0±0.05 2.0±0.05

160min. Taping 200min.

300min.

Drawing direction

Typ e A B C

MLG0402Q 0.4 max. 0.26±0.04 0.46±0.04

MLG0603P 0.5 max. 0.38±0.05 0.68±0.05