Caution Although this device is designed to be as robust as possible, ESD (Electrostatic
Discharge) can damage this device. This device must be protected at all times from ESD. Static
charges may easily produce potentials of several kilovolts on the human body or equipment, which
can discharge without detection. Industry-standard ESD precautions must be employed at all times.
0.05 to 3.0 GHz SPDT SWITCH
GaAs INTEGRATED CIRCUIT
PG2408TK
Document No. PG10771EJ01V0DS (1st edition)
Date Published July 2009 NS
DESCRIPTION
The
PG2408TK is a GaAs MMIC for L, S-band SPDT (Single Pole Double Throw) switch for 2.4 GHz wireless
LAN, mobile phone and other L, S-band applications.
This device operates with dual control switching voltages of 2.5 to 5.3 V. This device can operate at frequencies
from 0.05 to 3.0 GHz, with low insertion loss and high isolation.
This device is housed in a 6-pin lead-less minimold package (1511 PKG) and is suitable for high-density surface
mounting.
FEATURES
Switch control voltage : Vcont (H) = 3.0 V TYP.
: Vcont (L) = 0 V TYP.
Low insertion loss : Lins = 0.40 dB TYP. @ f = 1.0 GHz
: Lins = 0.50 dB TYP. @ f = 2.5 GHz
High isolation : ISL = 27 dB TYP. @ f = 1.0 GHz
: ISL = 18 dB TYP. @ f = 2.5 GHz
Handling power : Pin (0.1 dB) = +29.0 dBm TYP. @ f = 0.5 to 3.0 GHz
High-density surface mounting : 6-pin lead-less minimold package (1.5 1.1 0.55 mm)
APPLICATIONS
L, S-band digital cellular or cordless telephone
W-LAN, WLL and BluetoothTM etc.
ORDERING INFORMATION
Part Number
Order Number
Package
Marking
Supplying Form
PG2408TK-E2
PG2408TK-E2-A
6-pin lead-less minimold
(1511 PKG) (Pb-Free)
G5X
Embossed tape 8 mm wide
Pin 1, 6 face the perforation side of the tape
Qty 5 kpcs/reel
Remark To order evaluation samples, please contact your nearby sales office.
Part number for sample order:
PG2408TK-A
Data Sheet PG10771EJ01V0DS
2
PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM
Pin No.
Pin Name
1
RF1
2
GND
3
RF2
4
Vcont2
5
RFC
6
Vcont1
SW TRUTH TABLE
ON Path
Vcont1
Vcont2
RFC-RF1
Low
High
RFC-RF2
High
Low
ABSOLUTE MAXIMUM RATINGS (TA = +25C, unless otherwise specified)
Parameter
Symbol
Ratings
Unit
Switch Control Voltage
Vcont
+6.0 Note
V
Input Power
Pin
+33.0
dBm
Operating Ambient Temperature
TA
45 to +85
C
Storage Temperature
Tstg
55 to +150
C
Note Vcont1 Vcont2 6.0 V
RECOMMENDED OPERATING RANGE (TA = +25C, unless otherwise specified)
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
Operating Frequency
f
0.05
3.0
GHz
Switch Control Voltage (H)
Vcont (H)
2.5
3.0
5.3
V
Switch Control Voltage (L)
Vcont (L)
0.2
0
0.2
V
Control Voltage Difference
Vcont (H),
Vcont (L)Note
0.1
0
0.1
V
Note
Vcont (H) = Vcont1 (H) Vcont2 (H)
Vcont (L) = Vcont1 (L) Vcont2 (L)
Data Sheet PG10771EJ01V0DS
3
ELECTRICAL CHARACTERISTICS
(TA = +25C, Vcont (H) = 3.0 V, Vcont (L) = 0 V, DC blocking capacitors = 56 pF, unless otherwise
specified)
Parameter
Symbol
Test Conditions
MIN.
TYP.
MAX.
Unit
Insertion Loss 1
Lins1
f = 0.05 to 0.5 GHz Note 1
0.40
0.55
dB
Insertion Loss 2
Lins2
f = 0.5 to 1.0 GHz
0.40
0.55
dB
Insertion Loss 3
Lins3
f = 1.0 to 2.0 GHz
0.48
0.63
dB
Insertion Loss 4
Lins4
f = 2.0 to 2.5 GHz
0.50
0.65
dB
Insertion Loss 5
Lins5
f = 2.5 to 3.0 GHz
0.56
0.70
dB
Isolation 1
ISL1
f = 0.05 to 0.5 GHz Note 1
24
27
dB
Isolation 2
ISL2
f = 0.5 to 1.0 GHz
24
27
dB
Isolation 3
ISL3
f = 1.0 to 2.0 GHz
16
19
dB
Isolation 4
ISL4
f = 2.0 to 2.5 GHz
15
18
dB
Isolation 5
ISL5
f = 2.5 to 3.0 GHz
14
17
dB
Input Return Loss 1
RLin1
f = 0.05 to 0.5 GHz Note 1
15
20
dB
Input Return Loss 2
RLin2
f = 0.5 to 3.0 GHz
15
20
dB
Output Return Loss 1
RLout1
f = 0.05 to 0.5 GHz Note 1
15
20
dB
Output Return Loss 2
RLout2
f = 0.5 to 3.0 GHz
15
20
dB
0.1 dB Loss Compression
Pin (0.1 dB)
f = 2.0/2.5 GHz
+27.0
+29.0
dBm
Input Power Note 2
f = 0.5 to 3.0 GHz
+29.0
dBm
Input 3rd Order Intercept Point
IIP3
f = 0.5 to 3.0 GHz, 2 tone,
5 MHz spicing
+60
dBm
Switch Control Current
Icont
No RF input
0.3
20
A
Switch Control Speed
tSW
50% CTL to 90/10% RF
50
500
ns
Notes 1. DC blocking capacitors = 1 000 pF at f = 0.05 to 0.5 GHz
2. Pin (0.1 dB) is the measured input power level when the insertion loss increases 0.1 dB more than that of
linear range.
Caution It is necessary to use DC blocking capacitors with this device.
The value of DC blocking capacitors should be chosen to accommodate the frequency of
operation, bandwidth, switching speed and the condition with actual board of your system. The
range of recommended DC blocking capacitor value is less than 100 pF for frequencies above
0.5 GHz, and 1 000pF for frequencies above 0.5 GHz.
Data Sheet PG10771EJ01V0DS
4
EVALUATION CIRCUIT
Note C1 : 0.05 to 0.5 GHz 1 000 pF
: 0.5 to 3.0 GHz 56 pF
C2 : 1 000 pF
The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.
APPLICATION INFORMATION
LESD provides a means to increase the ESD protection on a specific RF port, typically the port attached to the
antenna.
The value may be tailored to provide specific electrical responses.
The RF ground connections should be kept as short as possible and connected to directly to a good RF ground
for best performance.
Data Sheet PG10771EJ01V0DS
5
ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD
USING THE EVALUATION BOARD
Symbol
Test Conditions
Values
C1
f = 0.05 to 0.5 GHz
1 000 pF
f = 0.5 to 3.0 GHz
56 pF
C2
1 000 pF
Data Sheet PG10771EJ01V0DS
6
TYPICAL CHARACTERISTICS (
T
A
= +25
C, DC blocking capacitors = 56 pF, unless otherwise specified
)
Remark The graphs indicate nominal characteristics.
Data Sheet PG10771EJ01V0DS
7
Remark The graphs indicate nominal characteristics.
Data Sheet PG10771EJ01V0DS
8
MOUNTING PAD LAYOUT DIMENSIONS
6-PIN LEAD-LESS MINIMOLD (1511 PKG) (UNIT: mm)
Remark The mounting pad layout in this document is for reference only.
When designing PCB, please consider workability of mounting, solder joint reliability, prevention of
solder bridge and so on, in order to optimize the design.
Data Sheet PG10771EJ01V0DS
9
PACKAGE DIMENSIONS
6-PIN LEAD-LESS MINIMOLD (1511 PKG) (UNIT: mm)
Data Sheet PG10771EJ01V0DS
10
RECOMMENDED SOLDERING CONDITIONS
This product should be soldered and mounted under the following recommended conditions. For soldering
methods and conditions other than those recommended below, contact your nearby sales office.
Soldering Method
Soldering Conditions
Condition Symbol
Infrared Reflow
Peak temperature (package surface temperature) : 260C or below
Time at peak temperature : 10 seconds or less
Time at temperature of 220C or higher : 60 seconds or less
Preheating time at 120 to 180C : 12030 seconds
Maximum number of reflow processes : 3 times
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
IR260
Wave Soldering
Peak temperature (molten solder temperature) : 260C or below
Time at peak temperature : 10 seconds or less
Preheating temperature (package surface temperature) : 120C or below
Maximum number of flow processes : 1 time
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
WS260
Partial Heating
Peak temperature (terminal temperature) : 350C or below
Soldering time (per side of device) : 3 seconds or less
Maximum chlorine content of rosin flux (% mass) : 0.2%(Wt.) or below
HS350
Caution Do not use different soldering methods together (except for partial heating).
Data Sheet PG10771EJ01V0DS 11
Caution GaAs Products
This product uses gallium arsenide (GaAs).
GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the
following points.
• Follow related laws and ordinances when disposing of the product. If there are no applicable laws
and/or ordinances, dispose of the product as recommended below.
1. Commission a disposal company able to (with a license to) collect, transport and dispose of
materials that contain arsenic and other such industrial waste materials.
2. Exclude the product from general industrial waste and household garbage, and ensure that the
product is controlled (as industrial waste subject to special control) up until final disposal.
• Do not burn, destroy, cut, crush, or chemically dissolve the product.
• Do not lick the product or in any way allow it to enter the mouth.