SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT VOLTAGE ADJ. RANGE
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
EFFICIENCY (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER TEMPERATURE
SAFETY STANDARDS
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVERLOAD
OVER VOLTAGE
AC CURRENT (Typ.)
1200ms, 40ms/230VAC at full load
16ms/230VAC at full load
180 ~ 264VAC 250 ~ 370VDC
47 ~ 63Hz
89%
≧0.7
4A/230VAC
54 ~ 60V
COLD START 40A/230VAC
<3.5mA / 240VAC
105 ~ 150% rated output power
30 ~ 36V
Protection type : Constant current limiting, recovers automatically after fault condition is removed
Protection type : Shut down o/p voltage, re-power on to recover
100 5 (TSW : detect on heatsink of power switch)℃± ℃
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
UL508, UL60950-1, TUV EN60950-1 approved
,EAC TP TC 004
Compliance to EN55032 (CISPR32) Class B, EN61000-3-2,-3, EAC TP TC 020
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61000-6-2 (EN50082-2), heavy industry level, criteria A, EAC TP TC 020
-20 ~ +70 (Refer to "Derating Curve")℃
20 ~ 90% RH non-condensing
-20 ~ +85 , 10 ~ 95% RH℃
±℃ ℃)0.03%/ (0 ~ 50
Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6
180.9Khrs min. MIL-HDBK-217F (25 )℃
227*125.2*100mm (W*H*D)
2.4Kg; 6pcs/15Kg/1.75CUFT
File Name:DRP-480-SPEC 2018-01-12
POWER FACTOR (Typ.)
DRP-480-48
48V
10A
0 ~ 10A
480W
120mVp-p
48 ~ 53V
±1.0%
±0.5%
±1.0%
DRP-480-24
24V
20A
0 ~ 20A
480W
120mVp-p
24 ~ 28V
±1.0%
±0.5%
±1.0%
Built-in passive PFC function compliance to EN61000-3-2
High efficiency 89% and low dissipation
Protections: Short circuit / Overload / Over voltage / Over temperature
Cooling by free air convection
Built-in constant current limiting circuit
Can be installed on DIN rail TS-35/7.5 or 15
UL 508(industrial control equipment)approved
EN61000-6-2(EN50082-2) industrial immunity level
100% full load burn-in test
3 years warranty
■ Features :
DRP-480 series
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC I/P-FG:2.0KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃
ENVIRONMENT
SAFETY &
EMC
(Note 4)
PROTECTION
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
5. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃
480W Single Output Industrial DIN RAIL with PFC Function
EMC IMMUNITY
EMC EMISSION
Bauar
Sicherheit
egel gema
tgepruft
od
be
www.
ID 2000000000
tuv.com
wac g
os
NRND
Mechanical Specification
Derating Curve Output Derating VS Input Voltage
Case No.930 Unit:mm
AMBIENT TEMPERATURE ( )℃INPUT VOLTAGE (V) 60Hz
180 190 200 264
100
90
80
70
60
50
40
LOAD (%)
LOAD (%)
-20 0 10 20 30 40 50 60 70 (VERTICAL)
20
40
60
80
100
Block Diagram fosc : 70KHz
O.V.P.
CONTROL
FG
I/P -V
+V
RECTIFIERS
&
FILTER
SWITCHING
POWER
FILTER
&
RECTIFIERS
FILTER PFC
EMI PASSIVE
O.L.P.
DETECTION
CIRCUIT
PWM
O.T.P.
CURRENT
LIMIT
Terminal Pin No. Assignment (TB1)
Terminal Pin No. Assignment (TB2)
Pin No.
Pin No.
1
1,2
2
3,4
3
Assignment
Assignment
FG
AC/N(DC-)
AC/L(DC+)
DC OUTPUT +V
DC OUTPUT -V
ADMISSIBLE DIN-RAIL: TS35/7.5 OR TS35/15
35
227100
+V ADJ.
312
TB1 TB2
125.2
34
LED 21
DRP-480 series
480W Single Output Industrial DIN RAIL with PFC Function
File Name:DRP-480-SPEC 2018-01-12
NRND
