IHA01 Series DC-DC Converter
Input
Output
Characteristic Minimum Typical Maximum Units Notes & Conditions
Output Voltage 3.3 30 VDC See Models and Ratings table
Initial Set Accuracy ±3 % At full load
Minimum Load 10 % Minimum load required to meet specified regulation
Line Regulation ±1.2 %/1% Output changes by max of 1.2% for each 1% change in
input voltage
Load Regulation 10 % From 10% to full load, see application note
Cross Regulation ±4 % On dual output models, when one output is at 25% load
and other is varied from 10% load to full load
Ripple & Noise 200 mV pk-pk 20 MHz bandwidth. Measured using 10 µF electrolytic in
parallel with 0.1 µF ceramic capacitor
Short Circuit Protection Continuous
Maximum Capacitive Load See Models and Ratings table
Temperature Coefficient 0.03 %/ ˚C
Characteristic Minimum Typical Maximum Units Notes & Conditions
Input Voltage Range
4.5 5.5
VDC
5 V nominal
8.1 9.9 9 V nominal
10.8 13.2 12 V nominal
13.5 16.5 15 V nominal
21.6 26.4 24 V nominal
Input Reflected Ripple Current 20 mA pk-pk Through 12 µH inductor and 47 µF capacitor
Input Surge
7
VDC for 100 ms
5 V nominal
12 9 V nominal
15 12 V nominal
18 15 V nominal
28 24 V nominal
xxx Series
www.xppower.com
1
• High Isolation, 6000 V
• 250 VAC Working Voltage
• Single and Dual Outputs
• Bipolar Outputs for MOSFET and IGBT Drives
• SIP7 Package
• -40 °C to +85 °C Operation
• Full Load at 85 °C Ambient
• MTBF 2.5 MHrs
• 3 Year Warranty
Dimensions:
IHA01:
0.77 x 0.39 x 0.49” (19.5 x 9.8 x 12.5 mm)
1 Watt
Mechanical Details
0.39 (9.8)
0.02
(0.5)
0.01
(0.25)
0.39
(9.8)
0.09
(2.4)
0.08
(2.13)
0.02
(0.5)
0.49
(12.5)
Printed
Face
12 5 76
0.77 (19.5)
0.60 (15.24)
0.12
(3.0)
0.02
(0.5)
0.47
(12.0)
0.10
(2.54)
1. All dimensions are in inches (mm)
2. Weight: 0.009 lbs (4.3 g) approx.
3. Pin diameter: 0.02±0.002 (0.5±0.05)
4. Pin pitchand length tolerance: ±0.014 (±0.35)
5. Case tolerance: ±0.02 (±0.5)
Notes
Pin Connections
Pin Single Dual
1 +Vin +Vin
2 -Vin -Vin
5 -Vout -Vout
6 No Pin Common
7 +Vout +Vout
IHA01 Series
www.xppower.com 2
DC-DC Converter
Models & Ratings
Notes
Input currents measured at nominal input voltage.
General
Characteristic Minimum Typical Maximum Units Notes & Conditions
Efficiency 77 % See Models and Ratings table
Isolation: Input to Output 6000 VDC
Isolation Working Voltage 250 VAC
Isolation Resistance 109Ω
Isolation Capacitance 10 pF
Switching Frequency 20 50 kHz
Power Density 6.8 W/in3
Mean Time Between Failure 2.39 MHrs MIL-HDBK-217F, +25 °C GB
Weight 0.009 (4.2) lb (g)
Input Voltage Output Voltage Output Current Input current Max. capacitive load Efficiency Model Number
No Load Full Load
4.5-5.5 V
3V3 303 mA 30 mA 280 mA 220 µF 71% IHA0105S3V3
5 V 200 mA 30 mA 265 mA 220 µF 75% IHA0105S05
9 V 111 mA 30 mA 260 mA 220 µF 77% IHA0105S09
12 V 83 mA 45 mA 265 mA 220 µF 76% IHA0105S12
15 V 67 mA 40 mA 260 mA 220 µF 77% IHA0105S15
±3V3 ±151 mA 30 mA 275 mA ±100 µF 73% IHA0105D03
±5 V ±100 mA 30 mA 265 mA ±100 µF 75% IHA0105D05
±9 V ±56 mA 30 mA 260 mA ±100 µF 77% IHA0105D09
±12 V ±42 mA 45 mA 265 mA ±100 µF 76% IHA0105D12
±15 V ±33 mA 40 mA 260 mA ±100 µF 77% IHA0105D15
+15 V / -9 V +33 mA / -55 mA 40 mA 265 mA ±100 µF 76% IHA0105D1509
8.1-9.9 V
3V3 303 mA 20 mA 155 mA 220 µF 72% IHA0109S3V3
5 V 200 mA 25 mA 145 mA 220 µF 77% IHA0109S05
9 V 111 mA 25 mA 140 mA 220 µF 79% IHA0109S09
12 V 83 mA 25 mA 145 mA 220 µF 77% IHA0109S12
15 V 67 mA 25 mA 140 mA 220 µF 79% IHA0109S15
±3V3 ±151 mA 25 mA 155 mA ±100 µF 73% IHA0109D03
±5 V ±100 mA 25 mA 150 mA ±100 µF 75% IHA0109D05
±9 V ±56 mA 25 mA 140 mA ±100 µF 79% IHA0109D09
±12 V ±42 mA 25 mA 145 mA ±100 µF 77% IHA0109D12
±15 V ±33 mA 25 mA 140 mA ±100 µF 79% IHA0109D15
+15 V / -9 V +33 mA / -55 mA 25 mA 140 mA ±100 µF 78% IHA0109D1509
10.8-13.2 V
3V3 303 mA 20 mA 120 mA 220 µF 70% IHA0112S3V3
5 V 200 mA 20 mA 115 mA 220 µF 73% IHA0112S05
9 V 111 mA 20 mA 110 mA 220 µF 77% IHA0112S09
12 V 83 mA 20 mA 115 mA 220 µF 73% IHA0112S12
15 V 67 mA 20 mA 110 mA 220 µF 76% IHA0112S15
±3V3 ±151 mA 20 mA 115 mA ±100 µF 72% IHA0112D03
±5 V ±100 mA 20 mA 115 mA ±100 µF 73% IHA0112D05
±9 V ±56 mA 20 mA 110 mA ±100 µF 77% IHA0112D09
±12 V ±42 mA 20 mA 115 mA ±100 µF 74% IHA0112D12
±15 V ±33 mA 20 mA 110 mA ±100 µF 76% IHA0112D15
+15 V / -9 V +33 mA / -55 mA 20 mA 110 mA ±100 µF 76% IHA0112D1509
13.5-16.5 V
3V3 303 mA 15 mA 91 mA 220 µF 73% IHA0115S3V3
5 V 200 mA 15 mA 87 mA 220 µF 77% IHA0115S05
9 V 111 mA 15 mA 83 mA 220 µF 80% IHA0115S09
12 V 83 mA 15 mA 83 mA 220 µF 80% IHA0115S12
15 V 67 mA 15 mA 84 mA 220 µF 79% IHA0115S15
±3V3 ±151 mA 15 mA 89 mA ±100 µF 75% IHA0115D03
±5 V ±100 mA 15 mA 84 mA ±100 µF 79% IHA0115D05
±9 V ±56 mA 15 mA 82 mA ±100 µF 81% IHA0115D09
±12 V ±42 mA 15 mA 83 mA ±100 µF 80% IHA0115D12
±15 V ±33 mA 15 mA 83 mA ±100 µF 80% IHA0115D15
+15 V / -9 V +33 mA / -55 mA 12 mA 79 mA ±100 µF 84% IHA0115D1509
21.6-26.4 V
3V3 303 mA 15 mA 60 mA 220 µF 70% IHA0124S3V3
5 V 200 mA 15 mA 59 mA 220 µF 71% IHA0124S05
9 V 111 mA 15 mA 60 mA 220 µF 70% IHA0124S09
12 V 83 mA 15 mA 58 mA 220 µF 72% IHA0124S12
15 V 67 mA 15 mA 57 mA 220 µF 73% IHA0124S15
±3V3 ±151 mA 10 mA 61 mA ±100 µF 68% IHA0124D03
±5 V ±100 mA 15 mA 60 mA ±100 µF 69% IHA0124D05
±9 V ±56 mA 15 mA 57 mA ±100 µF 73% IHA0124D09
±12 V ±42 mA 15 mA 58 mA ±100 µF 72% IHA0124D12
±15 V ±33 mA 15 mA 56 mA ±100 µF 75% IHA0124D15
+15 V / -9 V +33 mA / -55 mA 15 mA 56 mA ±100 µF 74% IHA0124D1509
3
IHA01 Series
www.xppower.com
DC-DC Converter
3
Mechanical Details
EMC: Immunity
Phenomenon Standard Test Level Criteria Notes & Conditions
ESD Immunity EN61000-4-2 ±6/±8 kV A Contact/Air Discharge
Radiated Immunity EN61000-4-3 10 Vrms A
EFT/Burst EN61000-4-4 2 kV A External components required,
see application notes
Conducted Immunity EN61000-4-6 10 V rms A
Magnetic Fields EN61000-4-8 1 A/m A
0.39 (9.8)
0.02
(0.5)
0.01
(0.25)
0.39
(9.8)
0.09
(2.4)
0.08
(2.13)
0.02
(0.5)
0.49
(12.5)
Printed
Face
12 5 76
0.77 (19.5)
0.60 (15.24)
0.12
(3.0)
0.02
(0.5)
0.47
(12.0)
0.10
(2.54)
1. All dimensions are in inches (mm)
2. Weight: 0.009 lbs (4.3 g) approx.
3. Pin diameter: 0.02±0.002 (0.5±0.05)
4. Pin pitch and length tolerance: ±0.014 (±0.35)
5. Case tolerance: ±0.02 (±0.5)
Notes
Pin Connections
Pin Single Dual
1 +Vin +Vin
2 -Vin -Vin
5 -Vout -Vout
6 No Pin Common
7 +Vout +Vout
EMC: Emissions
Phenomenon Standard Test Level Notes & Conditions
Conducted EN55022 Class B See Application Note
Radiated EN55022 Class B
Environmental
Characteristic Minimum Typical Maximum Units Notes & Conditions
Operating Temperature -40 +85 °C No thermal derating
Storage Temperature -40 +125 °C
Case Temperature +100 °C
Humidity 2.5 95 %RH Non-condensing
Cooling Natural convection
IHA01 Series
www.xppower.com
DC-DC Converter
23 Aug 16
Input component C1 is used to help meet EFT test requirements for the module.
Application Note
C1
IHA0105XXXX 470 µF/35 V
IHA0109XXXX 470 µF/35 V
IHA0112XXXX 470 µF/35 V
IHA0115XXXX 470 µF/35 V
IHA0124XXXX 470 µF/35 V
High limit
T
ypical Load Line
Low Limit
IHA01
I
Regulation
EFT Filter
Input filter components (C1,C2, C3 and L) are used to help meet conducted emissions requirements for the module. These components should be
mounted as close as possible to the module, and all leads should be minimised to decrease radiated noise.
C1 L C2 C3
IHA0105XXXX 1206, 4.7 µF/ 50 V 18 µH
IHA0109XXXX 1206, 4.7 µF/ 50 V 18 µH
IHA0112XXXX 1206, 4.7 µF/ 50 V 18 µH
IHA0115XXXX 1206, 4.7 µF/ 50 V 18 µH
IHA0124XXXX 1206, 4.7 µF/ 50 V 18 µH 1210, 2.2 µF/ 100 V 1206, 470 pF/ 2 kV
IHA01
C3
EMI Filter
