M29W800DB70N6F - Micron Technology, Inc.

March 2008 Rev 10 1/52

M29W800DT

M29W800DB

8-Mbit (1 Mbit x 8 or 512 Kbits x 16, boot block)

3 V supply flash memory

Features

■Supply voltage

–V

CC = 2.7 V to 3.6 V for program, erase and

read

■Access times: 45, 70, 90 ns

■Programming time

– 10 µs per byte/word typical

■19 memory blocks

– 1 boot block (top or bottom location)

– 2 parameter and 16 main blocks

■Program/erase contr oller

– Embedded byte/word program algorithms

■Erase suspend and resume modes

– Read and program anot her blo ck during

erase suspend

■Unlock bypass program command

– Faster production/batch programming

■Temporary block unprotection mode

■Common flash interface

– 64-bit security code

■Low power consumption

– Standby and automatic standby

■100,000 progr am/erase cycles per block

■Electronic signature

– Manufacturer co de: 0020h

– Top device code M29W800DT: 22D7h

– Bottom device code M29W800DB: 225Bh

FBGA

TFBGA48 (ZE)

6 x 8 mm

TSOP48 (N)

12 x 20 mm

SO44 (M)

www.numonyx.com

Contents M29W800DT, M29W800DB

2/52

Contents

1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Signal descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.1 Address inputs (A0-A18) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.2 Data inputs/outputs (DQ0-DQ7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.3 Data inputs/outputs (DQ8-DQ14) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.4 Data input/output or address input (DQ15A-1) . . . . . . . . . . . . . . . . . . . . . 12

2.5 Chip enable (E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.6 Output enable (G) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.7 Write enable (W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.8 Reset/block temporary unprotect (RP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.9 Ready/b u sy output (RB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.10 Byte/word organization select (BYTE) . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.11 VCC supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.12 VSS ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3 Bus operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.1 Bus read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.2 Bus write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.3 Output disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.4 Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.5 Automatic standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.6 Special bus operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.6.1 Electronic signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.6.2 Block protection and blocks unprotection . . . . . . . . . . . . . . . . . . . . . . . 16

4 Command interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.1 Read/Reset command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.2 Auto Select command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.3 Program command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.4 Unlock Bypass command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.5 Unlock Bypass Program command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

M29W800DT, M29W800DB Contents

3/52

4.6 Unlock Bypass Reset command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

4.7 Chip Erase command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.8 Block Erase command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.9 Erase Suspend command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.10 Erase Resume command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.11 Read CFI Query command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.12 Block Protect and Chip Unprotect commands . . . . . . . . . . . . . . . . . . . . . 20

5 Status register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.1 Data polling bit (DQ7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.2 Toggle bit (DQ6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

5.3 Error bit (DQ5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

5.4 Erase timer bit (DQ3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

5.5 Alternative toggle bit (DQ2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

7 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

8 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

9 Or dering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Appendix A Block address table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Appendix B Common flash interface (CFI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Appendix C Block protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

C.1 Programmer technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

C.2 In-system technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

List of tables M29W800DT, M29W800DB

4/52

List of tables

Table 1. Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Table 2. Bus operations, BYTE = VIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table 3. Bus operations, BYTE = VIH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table 4. Commands, 16-bit mode, BYTE = VIH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Table 5. Commands, 8-bit mode, BYTE = VIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 6. Program, erase times and program, erase endurance cycles . . . . . . . . . . . . . . . . . . . . . . 22

Table 7. Status register bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Table 8. Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Table 9. Operating and AC measurement conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 10. Device capacitance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table 11. DC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Table 12. Read AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Table 13. Write AC characteristics, write enable controlled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Table 14. Write AC characteristics, chip enable controlled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Table 15. Reset/block temporary unprotect AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Table 16. SO44 – 44 lead plast ic small outline, 525 mils body width, package mechanical data . . . 35

Table 17. TSOP48 – 48 lead plast ic thin small outline, 12 x 20 mm, package mechanical data . . . . 36

Table 18. TFBGA48 6 x 8 mm – 6 x 8 active ball array – 0.80 mm pitch, package mechanical data. 37

Table 19. Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Table 20. Top boot block addresses, M29W800DT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Table 21. Bottom boot block addresses, M29W800DB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Table 22. Query structure overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Table 23. CFI query identification string . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Table 24. CFI query system interface information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Table 25. Device geometry definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Table 26. Primary algorithm-specific extended query table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Table 27. Security code area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Table 28. Programmer technique bus operations, BYTE = VIH or VIL . . . . . . . . . . . . . . . . . . . . . . . . 46

Table 29. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

M29W800DT, M29W800DB List of figures

5/52

List of figures

Figure 1. Logic diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 2. SO connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Figure 3. TSOP connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Figure 4. TFBGA connections (top view through package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 5. Block addresses (x 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 6. Block addresses (x 16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 7. Data polling flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Figure 8. Data toggle flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 9. AC measurement I/O waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Figure 10. AC measurement load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Figure 11. Read mode AC waveforms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Figure 12. Write AC waveforms, write enable controlled. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Figure 13. Write AC waveforms, chip enable controlled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Figure 14. Reset/block temporary unprotect AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Figure 15. SO44 – 44 lead plast ic small outline, 525 mils body width, package outline . . . . . . . . . . . 34

Figure 16. TSOP48 – 48 lead plastic thin small outline, 12 x 20 mm, package outline . . . . . . . . . . . . 36

Figure 17. TFBGA48 6 x 8 mm – 6 x 8 ball array – 0.80 mm pitch, bottom view package outline. . . . 37

Figure 18. Programmer equipment block protect flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Figure 19. Programmer equipment chip unprotect flowchart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Figure 20. In-system equipment block protect flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Figure 21. In-system equipment chip unprotect flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Description M29W800DT, M29W800DB

6/52

1 Description

The M29W800D is a 8-Mbit (1 Mbit x 8 or 512 Kbits x 16) non-volatile memory that can be

read, erased and reprogrammed. These operations can be performed using a single low

voltage (2.7 to 3.6 V) supply. On power-up the memory defaults to its read mode where it

can be read in the same wa y as a ROM or EPROM.

The memory is divided into blocks that can be erased independently so it is possible to

preserve valid dat a while old data is erased. Each block can be protected independently to

prevent accidental program or erase commands from modifying the memory. Program and

erase commands are written to the command int erface of the memory. An on-chip

program/erase controller simplifies the process of programming or erasing the memory by

taking care of all of the special operations that are required to update the memory contents.

The end of a program or erase operation can be detected and any error conditions

identified. The command set required to control the memory is consistent with JEDEC

standards.

The b locks in the me mory are asymmetrically arran ged, see Figure 5: Block ad dresses (x 8)

and Figure 6: Block addresses (x 16). The first or last 64 Kbytes have been divided into four

additional blocks. The 16-Kbyte boot b lock can be used for small initialization code to start

the microprocessor, the two 8-Kbyte paramet er blocks can be used for parameter storage

and the remaining 32-Kbyte is a small main block where the application may be stored.

Chip Enable, Output Enable and Write Enable signals control the bus operation of the

memory. They allow simple connection to most microprocessors, often without additional

logic.

The memory is offered in SO44, TSOP48 (12 x 20 mm) and TFBGA48 6 x 8 mm (0.8 mm

pitch) packages. The memory is supplied with all the bits erased (set to ’1’).

Figure 1. Logic diagram

AI05470B

A0-A18

DQ0-DQ14

VCC

M29W800DT

M29W800DB

VSS

DQ15A–1

BYTE

M29W800DT, M29W800DB Description

7/52

Figure 2. SO connections

Table 1. Signal names

Signal Description Direction

A0-A18 Address inputs Inputs

DQ0-DQ7 Data inputs/outputs I/O

DQ8-DQ14 Data inputs/outputs I/O

DQ15A–1 Data input/output or address input I/O

EChip enable Input

GOutput enable Input

WWrite enable Input

RP Reset/block temporary unprotect Input

RB Ready/busy output (not available on SO44 package) Output

BYTE Byte/word organization select Input

VCC Supply voltage –

VSS Ground –

NC Not connected internally –

DQ0

DQ8

VSS

A13

VSS

A14

A15

DQ7

A12

A16

BYTE

DQ15A–1

DQ5DQ2

DQ3 VCC

DQ11 DQ4

DQ14

AI05462b

M29W800DT

M29W800DB

2322

17DQ1

DQ9

DQ6

DQ13

A11

A10

DQ10 21 DQ12

A17 A8

A18

Description M29W800DT, M29W800DB

8/52

Figure 3. TSOP connections

DQ3

DQ9

DQ2

A6 DQ0

DQ6

A9 DQ13

A17

A10 DQ14

DQ12

DQ10

DQ15A–1

VCC

DQ4

DQ5

DQ7

AI05461

M29W800DT

M29W800DB

24 25

DQ8

A18

DQ1

DQ11

A12

A13

A16

A11

BYTE

A15

A14 VSS

VSS

M29W800DT, M29W800DB Description

9/52

Figure 4. TFBGA connections (top view through package)

AI00656

4321

DQ15

A–1

DQ10DQ8E

DQ13DQ11

DQ9

VSS

DQ6DQ1VSS

DQ14

A12

NCA17

A14A10NCA18A6A2

RP A8

DQ4

DQ3

VCC

DQ12

BYTE

A15A11NCA1

A16DQ7DQ5DQ2A0

DQ0

RB W A13

Description M29W800DT, M29W800DB

10/52

Figure 5. Block addresses (x 8)

1. Also see Appendix A: Block address table, Table 20 and Table 21 for a full listing of the block addresses.

AI05463

16 Kbyte

FFFFFh

FC000h

64 Kbyte

1FFFFh

10000h

64 Kbyte

0FFFFh

00000h

M29W800DT

Top boot block addresses (x 8)

32 Kbyte

F7FFFh

F0000h

64 Kbyte

E0000h

EFFFFh

Total of 15

64 Kbyte blocks

16 Kbyte

FFFFFh

F0000h 64 Kbyte

64 Kbyte

03FFFh

00000h

M29W800DB

bottom boot block addresses (x 8)

32 Kbyte

EFFFFh

1FFFFh 64 Kbyte

E0000h

10000h

Total of 15

64 Kbyte blocks

0FFFFh

08000h

8 Kbyte

FBFFFh

FA000h

F9FFFh

F8000h

8 Kbyte

07FFFh

06000h

05FFFh

04000h

M29W800DT, M29W800DB Description

11/52

Figure 6. Block addresses (x 16)

1. Also see Appendix A: Block address table, Table 20 and Table 21 for a full listing of the block addresses.

AI05464

8 Kword

7FFFFh

7E000h

32 Kword

0FFFFh

08000h

32 Kword

07FFFh

00000h

M29W800DT

Top boot block addresses (x 16)

16 Kword

7BFFFh

78000h

32 Kword

70000h

77FFFh

Total of 15

32 Kword blocks

8 Kword

7FFFFh

78000h 32 Kword

32 Kword

01FFFh

00000h

M29W800DB

Bottom boot block addresses (x 16)

16 Kword

77FFFh

0FFFFh 32 Kword

70000h

08000h

Total of 15

32 Kword blocks

07FFFh

04000h

4 Kword

7DFFFh

7D000h

7CFFFh

7C000h

4 Kword

03FFFh

03000h

02FFFh

02000h

Signal descriptions M29W800DT, M29W800DB

12/52

2 Signal descriptions

See Figure 1: Logic diagram and Table 1: Signal names for a brief overview of the signals

connected to this device.

2.1 Address inputs (A0-A18)

The address inputs select the cells in the memory arra y to access during bus read

operations. During bus write operations they control the commands sent to the command

interface of the internal state machine.

2.2 Data inputs/outputs (DQ0-DQ7)

The data inputs/outputs output th e data stored at the selected address during a bus read

operation. During bus write operations they represent the commands sent to the command

interface of the internal state machine.

2.3 Data inputs/outputs (DQ8-DQ14)

The data inputs/outputs output th e data stored at the selected address during a bus read

operat ion when BYTE is High, VIH. When BYTE is Low, VIL, these pins are not used and ar e

high impedance . During b us write oper ations the com mand register does not use t hese bits .

When reading the status register th ese bits should be ignored.

2.4 Data input/output or address input (DQ15A-1)

When BYTE is High, VIH, this pin beha v es as a data input /output pin ( as DQ8-DQ14). When

BYTE is Low, VIL, this pin behaves as an address pin; DQ15A–1 Low will select the LSB of

the word on the other addresses, DQ15A–1 High will select the MSB. Throughout the text

consider references to the data input/output to include this pin when BYTE is High and

references to the address inputs to include this pin when BYTE is Low except when stated

explicitly otherwise.

2.5 Chip enable (E)

The chip enable, E, activates the memory, allowing bus read and bus write operatio ns to be

perf ormed. When Chip Enable is High, VIH, all other pins are ignored.

2.6 Output enable (G)

The output enable, G, controls the bus read operation of the memory.

M29W800DT, M29W800DB Signal descriptions

13/52

2.7 Write enable (W)

The write enable, W, controls the bus write operation of the memory’s command interface.

2.8 Reset/block temporary unprotect (RP)

The reset/block temporary unprotect pin can be used to apply a hardware reset to the

memory or to temporarily unprotect all blocks that have been protected.

A hardware reset is achieved by holding reset/block temporary unprotect Low, VIL, for at

least tPLPX. After rese t/block temporary unprotect goes High, VIH, the memory will be ready

for bus read and bus write operations after tPHEL or tRHEL, whichever occurs last. See the

Section 2.9: Ready/busy output (RB), Table 15: Reset/bloc k temporary unprotect AC

characteristics and Figure 14: Reset/block temporar y unprotect AC waveforms, for more

details.

Holding RP at VID will temporarily unprotect the protected blocks in the memory. Program

and erase oper ations on all blocks will be possible. The transition from VIH to VID must be

slower than tPHPHH.

2.9 Ready/busy output (RB)

The ready/busy pin is an open-dra in output that can be used to identify when the device is

perf orming a progr am or era se opera tion. During progr am or er ase oper ations ready/b usy is

Low, VOL. Ready/busy is high- impedance during read mode, auto select mode and er ase

suspend mode.

After a hardware reset, b us read and bus write operations cannot begin until ready/busy

becomes high-impedance. See Table 15: Reset/bloc k temporary unprotect AC

characteristics and Figure 14: Reset/block temporar y unprotect AC waveforms.

The use of an open-drain output allows the ready/busy pins from several memories to be

connected to a single pull-up resistor. A Low will then indicate that one, or more, of the

memories is busy.

2.10 Byte/w ord organization select (BYTE)

The byte/word organization select pin is used to switch between the 8-bit and 16-bit bus

modes of the memory. When byte/word organization select is Low, VIL, the memory is in 8-

bit mode, when it is High, VIH, the memory is in 16-bit mode.

2.11 VCC supply voltage

The VCC supply voltage supplies the power for all operations (read, program, erase etc.).

The command interface is disabled when the VCC supply voltage is less than the lockout

vo lt age, VLKO. This prevents bus write operations from accidentally damaging the data

during power-up, power-down and power surges. If the program/erase controller is

progr amming or erasin g during this time then th e operation abo rts and the memory contents

being altered will be invalid.

Signal descriptions M29W800DT, M29W800DB

14/52

A 0.1 µF capacitor should be connected between the VCC supply voltage pin and the VSS

ground pin to decouple the current surges from the power supply. The PCB track widths

must be sufficient to carry the currents required during program and erase operat ions, ICC3.

2.12 VSS ground

The VSS ground is the reference for all voltage measurements.

M29W800DT, M29W800DB Bus operations

15/52

3 Bus operations

There are five standard bus operations that control the device. These are bus read, bus

write, output disable, standby and automatic standby. See Table 2 and Table 3, Bus

operations, for a summary. Typically glitches of less than 5 ns on Chip Enable or Write

Enable are ignored by the memory and do not affect bus operations.

3.1 Bus read

Bus read operations read from the memory cells, or specific registers in the command

interface. A valid bus read operation involves setting the desir ed address on the address

inputs, applying a Low signal, VIL, to Chip Enable and Output Enable and keeping Write

Enable High, VIH. The data inputs/outputs will output the value, see Figure 11: Read mode

AC waveforms, and Figure 12: Read AC characteristics for details of when the output

becomes valid.

3.2 Bus write

Bus write operations write to the command interface. A valid bus write operation begins by

setting the desired address on the address inputs. The address inputs are latched by the

command interface on the falling edge of Chip Enable or Write Enable, whichever occurs

last. The data inputs/outputs are latched by the comm and interface on the rising edge of

Chip Enable or Write Enable, whichever occurs first. Output Enab le must remain High, VIH,

during the whole bus write operation. See Figure 12 and Figure 13, Write AC waveforms,

and Table 13 and Table 14, Write AC characteristics, for details of the timing requirement s.

3.3 Output disable

The data inputs/outputs are in the high impedance state when Output Enable is High, VIH.

3.4 Standby

When Chip Enable is High, VIH, the memory enters standb y mode and the data

inputs/outputs pins are placed in the high-impedance state. To reduce the supply curren t to

the standby supply current, ICC2, Chip Enable should be held within VCC ± 0.2 V. For the

standb y current level see Table 11: DC characteristics.

During program or erase operations the memory will continue to use the program/erase

supply current, ICC3, fo r pr ogram or erase operatio ns until th e op eratio n co mp le te s.

3.5 Automatic standby

If CMOS levels (VCC ± 0.2 V) are used to drive the bus and the bus is inactive for 150 ns or

more the memory enters automatic standby where the internal supply current is reduced to

the standby supply current, ICC2. The data inputs/outputs will still output data if a bus read

operat ion is in progress.

Bus operations M29W800DT, M29W800DB

16/52

3.6 Special bus operations

Additional bus operations can be performed to read the electronic signatu re and also to

apply and remove block protection. These bus operations are intended for use by

programming equipment and are not usually used in applications. They require VID to be

applied to some pins.

3.6.1 Electronic signature

The memory has two codes, the manufacturer code and the device code, that can be read

to identify the memory. These codes can be read by applying the signals listed in Table 2

and Table 3, Bus operations.

3.6.2 Block protection and blocks unprotection

Each block can be separately protected against accidental program or erase. Protected

bl ocks can be unprotected to allow data to be changed.

There are two methods available for protecting and unprotecting the blocks, one for use on

programming equipment and the other for in-system use. Block protect and chip unprotect

operations are described in Appendix C: Block protection.

Table 2. Bus operations, BYTE = VIL(1)

Operation E G W Address inputs

DQ15A–1, A0-A18

Data inputs/outputs

DQ14-DQ8 DQ7-DQ0

Bus read VIL VIL VIH Cell address Hi-Z Data output

Bus write VIL VIH VIL Command address Hi-Z Data input

Output disable X VIH VIH X Hi-Z Hi-Z

Standby VIH X X X Hi-Z Hi-Z

Read manufa cturer code VIL VIL VIH A0 = VIL, A1 = VIL, A9 =

VID, others VIL or VIH Hi-Z 20h

Read device code VIL VIL VIH A0 = VIH, A1 = VIL, A9 =

VID, others VIL or VIH Hi-Z D7h (M29W800DT)

5Bh (M29W800DB)

1. X = VIL or VIH.

Table 3. Bus operations, BYTE = VIH (1)

Operation E G W Address inputs

A0-A18 Data inputs/outputs

DQ15A–1, DQ14-DQ0

Bus read VIL VIL VIH Cell address Data output

Bus write VIL VIH VIL Command address Data input

Output disable X VIH VIH XHi-Z

Standby VIH XXX Hi-Z

Read manufacturer code VIL VIL VIH A0 = VIL, A1 = VIL, A9 = VID,

others VIL or VIH 0020h

Read device code VIL VIL VIH A0 = VIH, A1 = VIL, A9 = VID,

others VIL or VIH

22D7h (M29W800DT)

225Bh (M29W800DB)

1. X = VIL or VIH.

M29W800DT, M29W800DB Command interface

17/52

4 Command interface

All bus write operations to the memory are interpreted by the command interf ace.

Commands co nsis t of on e or mo re seque nt i al bus writ e op eratio ns. Failur e to obs erve a

v alid sequence of bus write operations will result in the memory returning to read mode. The

long command sequences are imposed to maximize data security.

The address used for the commands changes depending on whether the memory is in 16-

bit or 8-bit mode . See either Table 4, or Table 5, dependin g on the configur ation that is be ing

used, for a summary of the commands.

4.1 Read/Reset command

The Read/Reset command returns the memory to its read mode where it behaves like a

ROM or EPROM, unless otherwise stated. It also resets the errors in the status register.

Either one or three bus write operations can be used to issue the Read/Reset command.

The Read/Reset command can be issued, between bus write cycles before the start of a

program or erase operation, to return the device to read mode. Once the program or erase

operation has started the Read/Reset command is no longer accepted. The Read/Reset

command will not abort an erase operation when issued while in erase suspend.

4.2 Auto Select command

The Auto Select command is used to read the manufacturer code, the device code and the

block protection status. Three consecutive bus write operations are required to issue the

Auto Select command. Once the Auto Select command is issued the memory remains in

auto select mode unt il a Read/Reset comm and is issued. Re ad CFI Query and Read/Reset

commands are accepted in au to select mode, all other commands are ignored.

From the auto select mode the manufacturer code can be read using a bus read operation

with A0 = VIL and A1 = VIL. The other address bits may be set to either VIL or VIH. The

manufacturer code for Numonyx is 0020h.

The device code can be read using a bus read operation with A0 = VIH and A1 = VIL. The

other address bits may be set to either VIL or VIH. The device code for the M29W800DT is

22D7h and for the M29W800DB is 225Bh.

The block pro tection status of each block can be read using a bus read operation with A0 =

VIL, A1 = VIH, and A12-A1 8 specifying t he address of the block. The other add ress bits may

be set to either VIL or VIH. If the addressed block is protected then 01h is output on data

inputs/outputs DQ0-DQ7, otherwise 00h is output.

4.3 Program command

The Prog ram command can be used to prog ram a v alue to one address in the memory arra y

at a time. The command requires four bus write operations, the final write operation latches

the address and data in t he internal state machine and starts the program/erase controller.

If the address falls in a protected block then the Program command is ignored, the data

remains unchanged. The status register is never read and no error condition is given.

Command interface M29W800DT, M29W800DB

18/52

During the program operation the memory will ignore all commands. It is not possible to

issue any command to abort or pause the op eration. Typical program times are given in

Tabl e 6: Program, erase times and program, erase endurance cycles. Bus read operations

during the program operation will output the status register on the data inputs/outputs. See

the Section 5: Status register for more details.

After the program oper ation has completed the memory will return to the read mode, unless

an error has occurred. When an error occurs the memory will continue to output the status

read mode.

Note that the Prog ram comman d cann ot change a bit set to ’0’ back to ’1’. One of the erase

commands must be used to set all the bits in a block or in the whole memory from ’0’ to ’1’.

4.4 Unlock Bypass command

The Unloc k Bypass command is used in conjunction with the Unlock Bypass Program

command to program the memory. When the access time to the device is long (as with

some EPROM programmers) considerable time saving can be made by using these

commands. Three b us write operations are required to issue the Unlock Bypass co mmand.

Once the Unlock Bypass command has been issued the memory will only accept the Unlock

Bypass Program command and th e Unlo ck Bypass Reset comm a nd . The mem o ry can be

read as if in read mode.

4.5 Unlock Bypass Program command

The Unlock Bypass Program command can be used to program one address in memory at

a time. The command requires tw o bus write operatio ns, the fin al write operation latches the

address and data in the internal state machine and sta rts the progra m/erase controller.

The program operation using the Unlock Bypass Program command behaves identically to

the program operation using the Program command. A protected b lock cannot be

programmed; the operation cannot be aborted and the status register is read. Errors must

be reset using th e Read/Reset command, which leaves the device in unlock bypass mode.

See the Program command for details on the behavior.

4.6 Unlock Bypass Reset command

The Unlock Bypass Reset comman d can be use d to re tu rn to read/res et mode from unlock

bypass mode. Two bus write operations are required to issue the Unlock Bypass Reset

command. Read/Reset command does not exit from unlock bypass mode.

M29W800DT, M29W800DB Command interface

19/52

4.7 Chip Erase command

The Chip Er ase command can b e used to er ase the e ntire chip . Six bus write operatio ns are

required to issue the Chip Erase command and start the program/e rase controller.

If any blocks are protected then these are ignored and all the ot he r blocks are erased. If all

of the bloc ks are protected the chip erase operation appears to start but will terminate within

about 100 µs, leaving the data unchanged. No error condition is given when protected

blocks are ignored.

During the erase operation the memory will ignore all commands. It is not possible to issue

any command to abort the operation. Typical chip erase times are giv en in Table 6: Program,

erase times and program, erase endurance cycles. All bus read operations during the chip

erase operation will output the status register on the data inputs/outputs. See the Section 5:

Status register for more details.

After the chip erase operation has co mp le te d the me m ory will retu rn to the re ad mode,

unless an error has occurred. When an error occurs the memory will continue to output the

status register. A Read/Reset command must be issued to reset the error condition and

return to read mode.

The Chip Erase command sets all of the bits in unprotected blocks of the memory to ’1’. All

previous data is lost.

4.8 Block Erase command

The Bloc k Erase command can be used to erase a list of one or more blocks. Six bus write

operat ions are required to select the first b loc k in the list. Each additional bl ock in the list can

be selected by repe ating the sixth bus write operation using the address of the additional

bl ock. The block erase operation starts the program/erase controller about 50 µs after the

last bus write operation. Once the program/erase controller starts it is not possible to select

any more blocks. Each additional block must there fore be selected within 50 µs of the last

bl oc k. Th e 50 µs timer restarts when an additional b lock is selected. The status r egister can

be read after the sixth bus write operat ion. See the status register f or details on how to

identify if the program/erase controller has started the block erase operation.

If an y selected b l oc ks are prote cted then t hese are ignored and all the other selected b locks

are erased. If all of the selected blocks are protected the block erase operation appears to

start but will terminate within about 100 µs, leaving the data unchanged. No error condition

is given when protected blocks are ignored.

During the block erase operation the memory will ignore all commands except the Erase

Suspend command. Typical block er ase times are given in Table 6: Program, erase times

and program, erase endurance cycles. All bus read operations during the block erase

operation will output the status register on the data inputs/outputs. See the Section 5: Status

After the block erase operation has completed the memory will return to the read mode,

unless an error has occurred. When an error occurs the memory will continue to output the

status register. A Read/Reset command must be issued to reset the error condition and

return to read mode.

The Bloc k Erase command sets all of the bits in the unprotected selected blocks to ’1’. All

previous data in the selected blocks is lost.

Command interface M29W800DT, M29W800DB

20/52

4.9 Erase Suspend command

The Erase Susp end command may be used to tempora rily suspend a bloc k er ase oper ation

and return the memory to read mode. The command requires one bus write operation.

The program/erase controller will suspend within the erase suspend latency time (refer to

Table 6 for value) of the Erase Suspend command being issued. Once the program/erase

controller has stopped the memory will be set to read mode and the erase will be

suspended. If the Er ase Suspend command is issued during the period when the memory is

waiting for an additional block (before the program/erase controller starts) then the erase is

suspended immediately and will start immediately when the Erase Resume command is

issued. It is not possible to select any further blocks to erase after the erase resume.

During erase suspend it is possible to r ead and program cells in blocks that are not being

erased; bo th read and progr am operati ons behav e as normal on these bloc ks. If any attempt

is made to program in a protected block or in the suspended block then the Program

command is ignored and the data remains unchanged. The status register is not read and

no error condition is given. Reading from blocks that are being erased will output the status

It is also possible to issue the Auto Select, Read CFI Query and Unlock Bypass commands

during an erase suspe nd. The Re ad/Reset comman d must be issued to r eturn the de vice to

read array mode before the Resume command will be accepted.

4.10 Erase Resume command

The Erase Resume co mmand must be used to restart the program/ erase controller from

erase suspend. An erase can be suspende d and resumed more than once.

4.11 Read CFI Query command

The Read CFI Query command is used to read data from the common flash interface (CFI)

memory area. This command is valid when the de vice is in the read arr ay mode , or when the

de vice is in auto select mode.

One b us write cycle is required to issue the Read CFI Query command. Once the command

is issued subsequent bus read operations read from the common fl ash interface memory

area.

The Read/Reset command must be issued to return the device to the previous mode (read

array mode or auto select mode). A second Read/Reset co mmand would be needed if the

device is to be put in the read array mode from auto select mode.

See Appendix B: Common flash interface (CFI), Table 22, Table 23, Table 24, Table 25,

Table 26 and Table 27 f or details on the information contained in the common flash interface

(CFI) memory area.

4.12 Block Protect and Chip Unprotect commands

Each block can be separately protected against accidental program or erase. The whole

chip can be unprotected to allow the data inside the blocks to be changed.

Block protect and chip unpro tec t op eratio ns ar e de sc ribed in Appendix C: Block protection.

M29W800DT, M29W800DB Command interface

21/52

Table 4. Commands, 16-bit mode, BYTE = VIH(1)

Command

Length

Bus write operation s

1st 2nd 3rd 4th 5th 6th

Addr Data Addr Data Addr Data Addr Data Addr Data Addr Data

Read/Reset 1X F0

3 555 AA 2AA 55 X F0

Au to Select 3 555 AA 2AA 55 555 90

Program 4 555 AA 2AA 55 555 A0 PA PD

Unlock Bypass 3 555 AA 2AA 55 555 20

Unlock Bypass Program 2 X A0 PA PD

Unlock Bypass Reset 2 X 90 X 00

Chip Erase 6 555 AA 2AA 55 555 80 555 AA 2AA 55 555 10

Block Erase 6+ 555 AA 2AA 55 555 80 555 AA 2AA 55 BA 30

Erase Suspend 1 X B0

Erase Resume 1 X 30

Read CFI Query 1 55 98

1. X don’t care, PA program address, PD program data, BA any address in the block.

All values in the table are in hexadecimal format.

The command interface only uses A–1, A0-A10 and DQ0-DQ7 to verify the commands; A11-A18, DQ8-DQ14 and DQ15

are don’t care. DQ15A–1 is A–1 when BYTE is VIL or DQ15 when BYTE is VIH.

Command interface M29W800DT, M29W800DB

22/52

Table 5. Commands, 8-bit mode, BYTE = VIL(1)

Command

Length

Bus write operations

1st 2nd 3rd 4th 5th 6th

Addr Data Addr Data Addr Data Addr Data Addr Data Addr Data

Read/Reset 1X F0

3 AAA AA 555 55 X F0

Auto Select 3 AAA AA 555 55 AAA 90

Program 4 AAA AA 555 55 AAA A0 PA PD

Unlock Bypass 3 AAA AA 555 55 AAA 20

Unlock Bypass

Program 2X A0PAPD

Unlock Bypass Reset 2 X 90 X 00

Chip Erase 6 AAA AA 555 55 AAA 80 AAA AA 555 55 AAA 10

Block Erase 6+ AAA AA 555 5 5 AAA 80 AAA AA 555 55 BA 30

Erase Suspend 1 X B0

Erase Resume 1 X 30

Read CFI Query 1 AA 98

1. X don’t care, PA program address, PD program data, BA any address in the block.

All values in the table are in hexadecimal.

The command interface only uses A–1, A0-A10 and DQ0-DQ7 to verify the commands; A11-A18, DQ8-DQ14 and DQ15

are don’t care. DQ15A–1 is A–1 when BYTE is VIL or DQ15 when BYTE is VIH.

Table 6. Program, erase times and program, erase endurance cycles

Parameter Min. Typ. (1)(2) Max.(2) Unit

Chip erase 12 60(3) s

Block erase (64 Kbytes) 0.8 6(4) s

Erase suspend latency time 15 25(3) µs

Program (byte or word) 10 200(3) µs

Chip program (byte by byte) 12 60(3) s

Chip program (w ord by word) 6 30(4) s

Program/erase cycles (per block) 100,000 cycles

Data retention 20 years

1. Typical values measured at room temperature and nominal voltages.

2. Sampled, but not 100% tested.

3. Maximum value measured at worst case conditions for both temperature and VCC after 100,000 program/erase cycles.

4. Maximum value measured at worst case conditions for both temperature and VCC.

M29W800DT, M29W800DB Status register

23/52

5 Status register

Bus read operations from any address alw ays read the status register during program and

erase ope rations . It is also r ead during erase suspend when an address wit hin a bl ock be ing

erased is accessed.

The bits in the status register are summarized in Table 7: Status register bits.

5.1 Data polling bit (DQ7)

The data polling bit can be used to identify whether the program/erase controller has

successfully completed its operation or if it has responded to an erase suspend. The data

polling bit is output on DQ7 when the status register is read.

During program operations the data polling bit outputs the complement of the bit being

programmed to DQ7. After successful co mpletion of the program operation the memory

returns to read mode and bus read operations from the address just programmed output

DQ7, not its complement.

During erase operations the data polling bit outputs ’0’, the complement of the erased state

of DQ7. After successful completion of the erase operation the memory returns to read

mode.

In erase suspend mode the data polling bit will output a ’1’ during a bus read operation

within a block being erased. The data polling bit will change from a ’0’ to a ’1’ when the

program/erase controller has suspended the erase operation.

Figure 7: Data polling flowchart gives an example of how to use the data polling bit. A valid

address is the address being programmed or an address within the block being erased.

5.2 Toggle bit (DQ6)

The toggle b it can be used to identify whether the pr ogr am/erase controller ha s successfully

completed its operation or if it has responded to an er ase suspend. The toggle bit is output

on DQ6 when the status register is read.

During program and erase operations the toggle bit changes from ’0’ to ’1’ to ’0’, et c., with

successive bus read opera tions at any address . After successful complet ion of the operation

the memory returns to read mode.

During erase suspend mode the toggle bit will output when addressing a cell within a block

being erased. The toggle bit will stop toggling when the program/erase controller has

suspended the erase operation.

If any attempt is made to erase a protected block, the operation is aborted, no error is

signalled and DQ6 toggle s f or approximately 100 µs. If any attempt is made to program a

protected block or a suspended block, the operation is aborted, no error is signalled and

DQ6 toggles for approximately 1 µs.

Figure 8: Data toggle flowchar t gives an example of how to use th e toggle bit.

Status register M29W800DT, M29W800DB

24/52

5.3 Error bit (DQ5)

The error bit can be used to identify errors detected by the program/erase controller. The

error bit is set to ’1’ when a pro gram, block erase or chip erase operation fails to write the

correct data to the memory. If the error bit is set a Read/Reset command must be issued

before other commands are issued. The error bit is output on DQ5 when the status register

is read.

Note that the Prog ram command cannot cha nge a bit se t to ’0 ’ back to ’1’ and attempting to

do so will set DQ5 to ‘1’. A bus read oper ation to that address will show the bit is still ‘0’. One

of the erase commands must be used to set all the bits in a block or in the whole memory

from ’0’ to ’1’

5.4 Erase timer bit (DQ3)

The eras e timer bit can be used to identi fy the start of program/erase controller operation

during a Block Er ase comm and. Once the pr ogr am/ eras e contro ller starts erasing the era se

timer bit is set to ’1’. Bef ore the program/erase controller starts the erase timer bit is set to ’0’

and additional blocks to be erased may be written to the command interface. The erase

timer bit is output on DQ3 when the status register is read.

5.5 Alternative toggle bit (DQ2)

The alternative toggle bit can be used to monitor the program/erase controller during er ase

operations. The alternative toggle bit is output on DQ2 when the status register is read.

During chip erase and block erase operations the toggle bit changes from ’0’ to ’1’ to ’0’,

etc., with successive bus read operations from a ddresses within the blocks being erased. A

protected block is treated the same as a block not being erased. Once the operation

completes the memory returns to read mode.

During erase suspend the alternative t oggle bit changes from ’0’ to ’1’ to ’0’, etc. with

successive bus read operations from addresses within the blocks being erased. Bus re ad

operations to addresses within bloc ks not being erased will output the memory cell data as if

in read mode.

After an er ase operation that causes the error bit to be set the alternative toggle bit can be

used to identify which block or blocks have caused the er ror. The alternative toggle bit

changes from ’0’ to ’1’ to ’0’, etc. wit h successiv e b us rea d operation s from addresses within

bl ocks that have not erased correctly. The alternative toggle bit does not change if the

addressed bloc k has erased correctly.

M29W800DT, M29W800DB Status register

25/52

Figure 7. Data polling flowchart

Table 7. Status register bits(1)

Operation Address DQ7 DQ6 DQ5 DQ3 DQ2 RB

Program Any address DQ7 Toggle 0 – – 0

Program during erase

suspend Any address DQ7 Toggle 0 – – 0

Program error Any address DQ7 Toggle 1 – – 0

Chip erase Any address 0 Toggle 0 1 Toggle 0

Block erase before

timeout Erasing block 0 Toggle 0 0 Toggle 0

Non-erasing block 0 Toggle 0 0 No toggle 0

Block erase Erasing block 0 Toggle 0 1 Toggle 0

Non-erasing block 0 Toggle 0 1 No toggle 0

Erase suspend Erasing block 1 No toggle 0 – Toggle 1

Non-erasing block Data read as nor m al 1

Erase er ror Good block address 0 Toggle 1 1 No toggle 0

Faulty block address 0 Toggle 1 1 Toggle 0

1. Unspecified data bits should be ignored.

READ DQ5 & DQ7

at VALID ADDRESS

START

READ DQ7

at VALID ADDRESS

FAIL PASS

AI03598

DQ7

DATA YES

YES

DQ5

= 1

DQ7

DATA YES

Status register M29W800DT, M29W800DB

26/52

Figure 8. Data toggle flowchart

READ DQ6

START

READ DQ6

TWICE

FAIL PASS

AI01370C

DQ6

TOGGLE NO

YES

DQ5

= 1

YES

DQ6

TOGGLE

READ

DQ5 & DQ6

M29W800DT, M29W800DB Maximum rating

27/52

6 Maximum rating

Stressing the device above the rating listed in the Table 8: Absolute maximum ratings may

cause permanent damage to the device. Exposure to absolute maximum rating condit ions

for extended periods may affect device reliability. These are stress ratings only and

operation of the device at these or any other conditions above those indicated in the

operat ing sections of this specification is not implied. Refer also to the Numonyx SURE

program and other relevant quality documents.

Table 8. Absolute maximum ratings

Symbol Parameter Min Max Unit

TBIAS Temperature under bias –50 125 °C

TSTG Storage temperature –65 150 °C

VIO Input or output voltage (1) (2)

1. Minimum voltage may undershoot to –2 V during transition and for less than 20 ns during transitions.

2. Maximum voltage may overshoot to VCC + 2 V during transition and for less than 20 ns during transitions.

–0.6 VCC + 0.6 V

VCC Supply voltage –0.6 4 V

VID Identification voltage –0.6 13.5 V

DC and AC parameters M29W800DT, M29W800DB

28/52

7 DC and AC parameters

This section summarizes the operating measurement conditions, and the DC and AC

characteristics of the device. The parameters in the DC and AC characteristics tables that

follow, are derived from tests performed under the measurement conditions summarized in

Table 9: Operating and AC measurement conditions. Designers should check that the

operat ing conditions in their circuit match the operating conditions when relying on the

quoted parameters.

Figure 9. AC measurement I/O wavef orm

Table 9. Operating and AC measurement conditions

Parameter

M29W800D

Unit45 ns 70 ns 90 ns

Min Max Min Max Min Max

VCC supply voltage 3.0 3.6 2.7 3.6 2.7 3.6 V

Ambient operating temperature (range 6) –40 85 –40 85 –40 85 °C

Ambient operating temperature (range 1) 0 70 0 70 0 70

Load capacitance (CL) 30 30 100 pF

Input rise and fall times 10 10 10 ns

Input pulse voltages 0 to VCC 0 to VCC 0 to VCC V

Input and output timing ref. voltages VCC/2 VCC/2 VCC/2 V

AI04498

VCC

0 V

VCC/2

M29W800DT, M29W800DB DC and AC parameters

29/52

Figure 10. AC measurement load circuit

Table 10. Device c apacitance(1)

1. Sampled only, not 100% tested.

Symbol Parameter Test condition Min Max Unit

CIN Input capacitance VIN = 0 V 6 pF

COUT Output capacitance VOUT = 0 V 12 pF

Table 11. DC characteristics

Symbol Parameter Test condition Min Max Unit

ILI Input leakage current 0 V ≤ VIN ≤ VCC ±1 µA

ILO Output leakage current 0 V ≤ VOUT ≤ VCC ±1 µA

ICC1 Supply current (read) E=V

IL, G =V

IH,

f=6MHz 10 mA

ICC2 Supply current (standby) E=V

CC ±0.2V,

RP =V

CC ±0.2V 100 µA

ICC3 (1)

1. Sampled only, not 100% tested.

Supply current (program/erase) Program/erase

controller active 20 mA

VIL Input low v oltage –0.5 0.8 V

VIH Input high volt age 0.7VCC VCC +0.3 V

VOL Output low vol tag e IOL = 1.8 mA 0.45 V

VOH Output high voltage IOH =–100µAV

CC –0.4 V

VID Identification voltage 11.5 12.5 V

IID Identification current A9 = VID 100 µA

VLKO Program/erase lockout supply

voltage 1.8 2.3 V

AI04499

CL includes JIG capacitance

DEVICE

UNDER

TEST

25kΩ

VCC

25kΩ

VCC

0.1µF

DC and AC parameters M29W800DT, M29W800DB

30/52

Figure 11. Read mode AC waveforms

AI05448

tAVAV

tAVQV tAXQX

tELQX tEHQZ

tGLQV

tGLQX tGHQX

VALID

A0-A18/

A–1

DQ0-DQ7/

DQ8-DQ15

tELQV tEHQX

tGHQZ

VALID

tBHQV

tELBL/tELBH tBLQZ

BYTE

Table 12. Read AC characteristics

Symbol Alt P arameter Test condition M29W800D Unit

45 ns 70 ns 90 ns

tAVAV tRC Address Valid to Next Address Valid E = VIL,

G = VIL Min 45 70 90 ns

tAVQV tACC Address Valid to Output Valid E = VIL,

G = VIL Max 45 70 90 ns

tELQX (1) tLZ Chip Enable Low to Output Transition G = VIL Min000ns

tELQV tCE Chip Enable Low to Output Valid G = VIL Max 45 70 90 ns

tGLQX (1) tOLZ Output Enable Low to Output Transition E = VIL Min000ns

tGLQV tOE Output Enable Low to Output Valid E = VIL Max 25 30 35 ns

tEHQZ (1) tHZ Chip Enable High to Output Hi-Z G = VIL Max 20 25 30 ns

tGHQZ (1) tDF Output Enable High to Output Hi-Z E = VIL Max 20 25 30 ns

tEHQX

tGHQX

tAXQX

tOH Chip Enable, Output Enable or Address

Transition to Output Transition Min000ns

tELBL

tELBH

tELFL

tELFH Chip Enable to BYTE Low or High Max 5 5 5 ns

tBLQZ tFLQZ BYTE Low to Output Hi-Z Max 25 25 30 ns

tBHQV tFHQV BYTE High to Output Valid Max 30 30 40 ns

1. Sampled only, not 100% tested.

M29W800DT, M29W800DB DC and AC parameters

31/52

Figure 12. Writ e AC waveforms, write enable controlled

AI05449

A0-A18/

A–1

DQ0-DQ7/

DQ8-DQ15

VALID

VCC

tVCHEL

tWHEH

tWHWL

tELWL

tAVWL

tWHGL

tWLAX

tWHDX

tAVAV

tDVWH

tWLWHtGHWL

tWHRL

Table 13. Write AC characteristics, write enable controlled

Symbol Alt Parameter M29W800D Unit

45 ns 70 ns 90 ns

tAVAV tWC Address Valid to Next Address Valid Min 45 70 90 ns

tELWL tCS Chip Enable Low to Write Enable Low Min 0 0 0 ns

tWLWH tWP Write Enable Low to Write Enable High Min 30 45 50 ns

tDVWH tDS Input Valid to Write Enable High Min 25 45 50 ns

tWHDX tDH Write Enable High to Input Transition Min 0 0 0 ns

tWHEH tCH Write Enable High to Chip Enable High Min 0 0 0 ns

tWHWL tWPH Write Enable High to Write Enable Low Min 30 30 30 ns

tAVWL tAS Address Valid to Write Enable Low Min 0 0 0 ns

tWLAX tAH Write Enable Low to Address Transition Min 40 45 50 ns

tGHWL Output Enable High to Write Enable Low M in 0 0 0 ns

tWHGL tOEH Write Enable High to Output Enable Low Min 0 0 0 ns

tWHRL (1) tBUSY Program/Erase Valid to RB Low Max 30 30 35 ns

tVCHEL tVCS VCC High to Chip Enable Low Min 50 50 50 µs

1. Sampled only, not 100% tested.

DC and AC parameters M29W800DT, M29W800DB

32/52

Figure 13. Writ e AC wav e forms, chip enable controlled

AI05450

A0-A18/

A–1

DQ0-DQ7/

DQ8-DQ15

VALID

VCC

tVCHWL

tEHWH

tEHEL

tWLEL

tAVEL

tEHGL

tELAX

tEHDX

tAVAV

tDVEH

tELEHtGHEL

tEHRL

Table 14. Write AC characteristics, chip enable controlled

Symbol Alt Parameter M29W800D Unit

45 ns 70 ns 90 ns

tAVAV tWC Address Valid to Next Address Valid Min 45 70 90 ns

tWLEL tWS Write Enable Low to Chip Enable Low Min 0 0 0 ns

tELEH tCP Chip Enable Low to Chip Enable High Min 30 45 50 ns

tDVEH tDS Input Valid to Chip Enab le High Min 25 45 50 ns

tEHDX tDH Chip Enable High to Input Transition Min 0 0 0 ns

tEHWH tWH Chip Enable High to Write Enable High Min 0 0 0 ns

tEHEL tCPH Chip Enable High to Chip Enable Low Min 30 30 30 ns

tAVEL tAS Address Valid to Chip Enable Low Min 0 0 0 ns

tELAX tAH Chip Enable Low to Address Transition Min 40 45 50 ns

tGHEL Output Enable High Chip Enable Low Min 0 0 0 ns

tEHGL tOEH Chip Enable High to Output Enable Low Min 0 0 0 ns

tEHRL (1) tBUSY Program/Erase Valid to RB Low Max 30 30 35 ns

tVCHWL tVCS VCC High to W rite Enable Low Min 50 50 50 µs

1. Sampled only, not 100% tested.

M29W800DT, M29W800DB DC and AC parameters

33/52

Figure 14. Reset/block temporary unprotect AC waveforms

AI06870

RP tPLPX

tPHWL, tPHEL, tPHGL

tPLYH

tPHPHH

E, G

tRHWL, tRHEL, tRHGL

Table 15. Reset/block temporary unprotect AC characteristics

Symbol Alt Parameter M29W800D Unit

45 ns 70 ns 90 ns

tPHWL (1)

tPHEL

tPHGL (1) tRH RP High to Write Enable Low, Chip Enable

Low, Output Enable Low Min 50 50 50 ns

tRHWL (1)

tRHEL (1)

tRHGL (1) tRB RB High to Write Enable Low, Chip Enable

Low, Output Enable Low Min000ns

tPLPX tRP RP pulse width Min 500 500 500 ns

tPLYH (1) tREADY RP Low to read mode Max 1 0 10 10 µs

tPHPHH (1) tVIDR RP rise time to VID Min 500 500 500 ns

1. Sampled only, not 100% tested.

Package mechanical data M29W800DT, M29W800DB

34/52

8 Package mechanical data

In order to mee t en viron mental requir ements , Numo nyx o ff er s these devices in ECOPA CK®

packages. These packages have a lead-free second level interconnect. The category of

second level interconnect is marked on the package and on the inner box label, in

compliance with JEDEC Standard JESD97. The maximum ratings related to soldering

conditions are also mark ed on the inner box label.

Figure 15. SO44 – 44 lead plastic small outline, 525 mils body wi dth, package outline

1. Drawing is not to scale.

SO-d

LA1 α

eCP

M29W800DT, M29W800DB Package mechanical data

35/52

Table 16. SO44 – 44 lead plastic small outline, 525 mils body width, package mechanical data

Symbol millimeters inches

Typ Min Max Typ Min Max

A 2.80 0.110

A1 0.10 0.004

A2 2.30 2.20 2.40 0.091 0.087 0.094

b 0.40 0.35 0.50 0.016 0.014 0.020

C 0.15 0.10 0.20 0.006 0.004 0.008

CP 0.08 0.003

D 28.20 28.00 28.40 1.110 1.102 1.118

E 13.30 13.20 13.50 0.524 0.520 0.531

EH 16.00 15.75 16.25 0.630 0.620 0.640

e 1.27 – – 0.050 – –

L 0.80 0.031

a8° 8°

N44 44

Package mechanical data M29W800DT, M29W800DB

36/52

Figure 16. TSOP48 – 48 lead plastic thin small outline, 12 x 20 mm, package outline

1. Drawing is not to scale.

TSOP-G

DIE

LA1 α

Table 17. TSOP48 – 48 lead plastic thin small outline, 12 x 20 mm, package mechanical data

Symbol millimeters inches

Typ Min Max Typ Min Max

A 1.20 0.047

A1 0.10 0.05 0.15 0.004 0.002 0.006

A2 1.00 0.95 1.05 0.039 0.037 0.041

B 0.22 0.17 0.27 0.009 0.007 0.011

C 0.10 0.21 0.004 0.008

CP 0.08 0.003

D1 12.00 11.90 12.10 0.472 0.468 0.476

E 20.00 19.80 20.20 0.787 0.779 0.795

E1 18.40 18.30 18.50 0.724 0.720 0.728

e 0.50 – – 0.020 – –

L 0.60 0.50 0.70 0.024 0.020 0.028

L1 0.80 0.031

a3°0°5°3°0°5°

M29W800DT, M29W800DB Package mechanical data

37/52

Figure 17. TFBGA48 6 x 8 mm – 6 x 8 ball array – 0.80 mm pitch, bottom view package outline

1. Drawing is not to scale.

E1E

BGA-Z32

ddd

FE SD

BALL "A1"

Table 18. TFBG A48 6 x 8 mm – 6 x 8 active ball array – 0.80 mm pitch, pack age mec hanical data

Symbol millimeters inches

Typ Min Max Typ Min Max

A 1.20 0.047

A1 0.26 0.010

A2 0.90 0.035

b 0.35 0.45 0.014 0.018

D 6.00 5.90 6.10 0.236 0.232 0.240

D1 4.00 – – 0.157 – –

ddd 0.10 0.004

E 8.00 7.90 8.10 0.315 0.311 0.319

E1 5.60 – – 0.220 – –

e 0.80 – – 0.031 – –

FD 1.00 – – 0.039 – –

FE 1.20 – – 0.047 – –

SD 0.40 – – 0.016 – –

SE 0.40 – – 0.016 – –

Ordering information M29W800DT, M29W800DB

38/52

9 Ordering information

Table 19. Ordering informati on scheme

Note: For a list of available options (speed, package, etc.) or for further information on an y aspect

of this device, please contact your nea rest Numonyx Sales Office.

Example: M29W800DB 90 N 6 T

Device type

M29

Operatin g voltage

W = VCC = 2.7 to 3.6 V

Device function

800D = 8-Mbit (x 8/x 16), boot block

Array matrix

T = top boot

B = bottom boot

Speed

45 = 45 ns

70 = 70 ns

90 = 90 ns

Package

M = SO44

N = TSOP48: 12 x 20 mm

ZE = TFBGA48: 6 x 8 mm, 0.80 mm pitch

Temperature range

6 = –40 to 85 °C

1 = 0 to 70 °C

Option

T = tape & reel packing

E = lead-free package, standard packing

F = lead-free package, tape & reel packing

M29W800DT, M29W800DB Block address table

39/52

Appendix A Block address table

Table 20. Top boot block addresses, M29W800DT

# Size (Kbytes) Address range (x 8) Address range (x 16)

18 16 FC000h-FFFFFh 7E000h-7FFFFh

17 8 FA000h-FBFFFh 7D000h-7DFFFh

16 8 F8000h-F9FFFh 7C000h-7CFFFh

15 32 F0000h-F7FFFh 78000h-7BFFFh

14 64 E0000h-EFFFFh 70000h-77FFFh

13 64 D0000h-DFFFFh 68000h-6FFFFh

12 64 C0000h-CFFFFh 60000h-67FFFh

11 64 B0000h-BFFFFh 58000h-5FFFFh

10 64 A0000h-AFFFFh 50000h-57FFFh

9 64 90000h-9FFFFh 48000h-4FFFFh

8 64 80000h-8FFFFh 40000h-47FFFh

7 64 70000h-7FFFFh 38000h-3FFFFh

6 64 60000h-6FFFFh 30000h-37FFFh

5 64 50000h-5FFFFh 28000h-2FFFFh

4 64 40000h-4FFFFh 20000h-27FFFh

3 64 30000h-3FFFFh 18000h-1FFFFh

2 64 20000h-2FFFFh 10000h-17FFFh

1 64 10000h-1FFFFh 08000h-0FFFFh

0 64 00000h-0FFFFh 00000h-07FFFh

Block address table M29W800DT, M29W800DB

40/52

Table 21. Bottom boot block addresses, M29W800DB

# Size (Kbytes) Address range (x 8) Address range (x 16)

18 64 F0000h-FFFFFh 78000h-7FFFFh

17 64 E0000h-EFFFFh 70000h-77FFFh

16 64 D0000h-DFFFFh 68000h-6FFFFh

15 64 C0000h-CFFFFh 60000h-67FFFh

14 64 B0000h-BFFFFh 58000h-5FFFFh

13 64 A0000h-AFFFFh 50000h-57FFFh

12 64 90000h-9FFFFh 48000h-4FFFFh

11 64 80000h-8FFFFh 40000h-47FFFh

10 64 70000h-7FFFFh 38000h-3FFFFh

9 64 60000h-6FFFFh 30000h-37FFFh

8 64 50000h-5FFFFh 28000h-2FFFFh

7 64 40000h-4FFFFh 20000h-27FFFh

6 64 30000h-3FFFFh 18000h-1FFFFh

5 64 20000h-2FFFFh 10000h-17FFFh

4 64 10000h-1FFFFh 08000h-0FFFFh

3 32 08000h-0FFFFh 04000h-07FFFh

2 8 06000h-07FFFh 03000h-03FFFh

1 8 04000h-05FFFh 02000h-02FFFh

0 16 00000h-03FFFh 00000h-01FFFh

M29W800DT, M29W800DB Common flash interface (CFI)

41/52

Appendix B Common flash interface (CFI)

The common flash interface is a JEDEC approved, standardized data structure that can be

read from the flash memory device. It allows a system software to query the device to

determine various electrical and timing parameters, density information and functions

supported by the memory. The system can interface easily with the device, enabling the

software to upgrade itself when necessary.

When the CFI Query command is issued the device enters CFI query mode and the data

structure is read from the memory. Table 22, Table 23, Table 24, Table 25, Table 26 and

Table 27 show the addresses used to retrieve the data.

The CFI data structure also co nt ains a security area wher e a 64 -b it uniq ue se curity n umb er

is written (see Table 27: Security code area). This area can be accessed only in read mode

by the final user. It is impossible to change the security number after it has been written by

Numonyx. Issue a Read command to return to read mode.

Table 22. Query structure overview (1)

1. Query data are always presented on the lowest order data outputs.

Address Sub-section name Description

x 16 x 8

10h 20h CFI query identification string Command set ID and algorithm data offset

1Bh 36h System interface information Device timing & voltage information

27h 4Eh Device geometry definition Flash device layout

40h 80h Primary algorithm-specific extended

query table Additional information specific to the

primary algorithm (optiona l)

61h C2h Security code area 64-bit unique device number

Common flash interface (CFI) M29W800DT, M29W800DB

42/52

Table 23. CFI query identification string(1)

1. Query data are always presented on the lowest order data outputs (DQ7-DQ0) only. DQ8-DQ15 are ‘0’.

Address Data Description Value

x 16 x 8

10h 20h 0051h ‘Q’

11h 22h 0052h Query unique ASCII string ‘QRY’ ‘R’

12h 24h 0059h ‘Y’

13h 26h 0002h Primary algorithm command set and control interface ID

code 16-bit ID code defining a specific algorithm AMD

compatible

14h 28h 0000h

15h 2Ah 0040h Address for prim ary algorithm extended query table (see

Table 26)P = 40h

16h 2Ch 0000h

17h 2Eh 0000h Alternate vendor command set and control interface ID

code second vendor - specified algorithm supported NA

18h 30h 0000h

19h 32h 0000h Address for alternate algorithm extended query table NA

1Ah 34h 0000h

Table 24. CFI query system interfa ce information

Address Data Description Value

x 16 x 8

1Bh 36h 0027h VCC logic supply minimum program/erase voltage

bit 7 to 4 BCD value in volts

bit 3 to 0 BCD value in 100 mV 2.7 V

1Ch 38h 0036h VCC logic supply maximum program/erase voltage

bit 7 to 4 BCD value in volts

bit 3 to 0 BCD value in 100 mV 3.6 V

1Dh 3Ah 0000h VPP [programming] supply minimum program/erase voltage NA

1Eh 3Ch 0000h VPP [programming] supply maximum program/erase voltage NA

1Fh 3Eh 0004h Typical timeout per single byte/word program = 2n µs 16 µs

20h 40h 0 000h Typical timeout for minimum size write buffer program = 2n µs NA

21h 42h 000Ah Typical timeout per individual bloc k er ase = 2n ms 1 s

22h 44h 0000h Typical timeout for full chip erase = 2n ms (1)

1. Not supported in the CFI.

23h 46h 0004h Maximum timeout for byte/word program = 2n times typical 2 56 µs

24h 48h 0000h Maximum timeout for write b uffer program = 2n times typical NA

25h 4Ah 0003h Maximum timeout per individual block erase = 2n times typical 8 s

26h 4Ch 0000h Maximum timeout for chip erase = 2n times typical (1)

M29W800DT, M29W800DB Common flash interface (CFI)

43/52

Table 25 . Device geometry definition

Address Data Description Value

x 16 x 8

27h 4Eh 0014h Device size = 2n in nu mber of bytes 1 Mbyte

28h

29h 50h

52h 0002h

0000h Flash device interface code description x 8, x 16

async.

2Ah

2Bh 54h

56h 0000h

0000h Maximum number of bytes in multi-by te program or page =

2n NA

2Ch 58h 0004h Number of erase block regions within the device.

It specifies the number of regions within the device

containing contiguous erase blocks of the same size. 4

2Dh

2Eh 5Ah

5Ch 0000h

0000h Region 1 information

Number of identical size erase block = 0000h+1 1

2Fh

30h 5Eh

60h 0040h

0000h Region 1 information

Block size in region 1 = 0040h * 256 bytes 16-Kbyte

31h

32h 62h

64h 0001h

0000h Region 2 information

Number of identical size erase block = 0001h+1 2

33h

34h 66h

68h 0020h

0000h Region 2 information

Block size in region 2 = 0020h * 256 bytes 8-Kbyte

35h

36h 6Ah

6Ch 0000h

0000h Region 3 information

Number of identical size erase block = 0000h+1 1

37h

38h 6Eh

70h 0080h

0000h Region 3 information

Block size in region 3 = 0080h * 256 byte 32-Kbyte

39h

3Ah 72h

74h 000Eh

0000h Region 4 information

Number of identical-size erase block = 000Eh+1 15

3Bh

3Ch 76h

78h 0000h

0001h Region 4 information

Block size in region 4 = 0100h * 256 byte 64-Kbyte

Common flash interface (CFI) M29W800DT, M29W800DB

44/52

Table 26. Primary algorithm-specific extended query table

Address Data Description Value

x 16 x 8

40h 80h 0050h Primary algorithm e xtended query table unique ASCII string

‘PRI’

‘P’

41h 82h 0052h ‘R’

42h 84h 0049h ‘I’

43h 86h 0031h Major version number, ASCII ‘1’

44h 88h 0030h Minor version number, ASCII ‘0’

45h 8Ah 0000h Address sensitive unlock (bits 1 to 0)

00 = required, 01= not required

silicon revision number (bits 7 to 2) Yes

46h 8Ch 0002h Erase suspend

00 = not supported, 01 = read only, 02 = read and write 2

47h 8Eh 0001h Block protecti on

00 = not supported, x = number of sectors in per group 1

48h 90h 0001h Temporary block unprotect

00 = not supported, 01 = supported Yes

49h 92h 0004h Bloc k protect /unp r o tect

04 = M29W800D 4

4Ah 94h 0000h Simultaneous operations, 00 = not supported No

4Bh 96h 0000h Burst mode, 00 = not supported, 01 = supported No

4Ch 98h 0000h Page mode, 00 = not supported, 01 = 4 page word, 02 = 8

page word No

Table 27. Security code area

Address Data Description

x 16 x 8

61h C3h, C2h XXXX

64-bit: unique device number

62h C5h, C4h XXXX

63h C7h, C6h XXXX

64h C9h, C8h XXXX

M29W800DT, M29W800DB Block protection

45/52

Appendix C Block protection

Bloc k protect ion can be used to prevent any operation from modifying the data stored in th e

Flash. Each block can be protected individually. Once protected, program and erase

operations on the b lock fail to change the data.

There are three techniques that can be used to cont rol block protection, these are the

programmer technique, the in-system technique and temporary unprotection. Temporary

unprotection is controlled by the reset/block temporar y unprotection pin, RP; this is

descr i be d in th e Section 2: Signal descriptions.

Unlike the command inte rface of the program/erase controller, the techniques f or protecting

and unprotecting blocks change between different Flash memory suppliers. For example,

the techniques for AMD parts will not work on Numonyx parts. Care should be taken when

changing drivers for one part to work on another.

C.1 Programmer technique

The programmer technique uses high (VID) voltage levels on some of the bus pins. These

cannot be achieved using a standard microprocessor bus, therefore the technique is

recommended only for use in programming equipment.

To protect a block follow the flowchart in Fi gu re 18: Programmer eq uip m en t block protect

flowchart. To unprotect t he whole chip it is ne cessary to protect all of the b loc ks f irst, then all

bl ocks can be unprotected at the same time. To unprotect the chip f ollow Figure 19:

Programmer equipment chip unprotect flowchart. Table 28: Programmer technique bus

operations, BYTE = VIH or VIL, gives a summary of each operation.

The timing on these flowcharts is critical. Care should be taken to ensure that, where a

pause is specified, it is followed as closely as possible. Do not abort the procedure before

reaching the end. Chip unprotect can take several seconds and a user message should be

provided to show th at the operation is progressing.

C.2 In-system technique

The in-system technique requires a high voltage level on the reset/blocks temporary

unprotect pin, RP. This can be achieved without violating the maximum ratings of the

components on the micro processor b us , ther ef or e this technique is suit ab le for use after the

Flash has been fitted to the system.

To protect a block follow the flowchart in Figure 20: In-system equipment block protect

flowchart. To unprotect t he whole chip it is ne cessary to protect all of the b loc ks f irst, then all

the blocks can be unprotected at the same time. To unprotect the chip follow Figure 21: In-

system equipm en t ch ip un pr otect flowchart.

The timing on these flowcharts is critical. Care should be taken to ensure that, where a

pause is specified, it is followed as closely as possible. Do not allow the microprocessor to

service interrupts that will upset the timing and do not abort the procedure before reaching

the end. Chip unprotect can take several seconds and a user message should be provided

to show that the operation is progressing.

Block protection M29W800DT, M29W800DB

46/52

Table 28. Programmer technique bus operations, BYTE = VIH or VIL

Operation E G W Address inputs

A0-A18 Data inputs/outputs

DQ15A–1, DQ14-DQ0

Block protect VIL VID VIL pulse A9 = VID, A12-A18 block address

others = X X

Chip unprotect VID VID VIL pulse A9 = VID, A12 = VIH, A15 = VIH

others = X X

Block protection

verify VIL VIL VIH

A0 = VIL, A1 = VIH, A6 = VIL, A9 = VID,

A12-A18 block address

others = X

Pass = XX01h

Retry = XX00h

Block unprotection

verify VIL VIL VIH

A0 = VIL, A1 = VIH, A6 = VIH,

A9 = VID, A12-A18 block address

others = X

Retry = XX01h

Pass = XX00h

M29W800DT, M29W800DB Block protection

47/52

Figure 18. Programmer equipment block protect flowchart

ADDRESS = BLOCK ADDRESS

AI03469

G, A9 = VID,

E = VIL

n = 0

Wait 4µs

Wait 100µs

W = VIL

W = VIH

E, G = VIH,

A0, A6 = VIL,

A1 = VIH

A9 = VIH

E, G = VIH

++n

= 25

START

FAIL

PASS

YES

DATA

01hYES

W = VIH

E = VIL

Wait 4µs

G = VIL

Wait 60ns

Read DATA

Verify Protect Set-upEnd

A9 = VIH

E, G = VIH

Block protection M29W800DT, M29W800DB

48/52

Figure 19. Programmer equipment chip unprotect flowchart

PROTECT ALL BLOCKS

AI03470

A6, A12, A15 = VIH(1)

E, G, A9 = VID

DATA

W = VIH

E, G = VIH

ADDRESS = CURRENT BLOCK ADDRESS

A0 = VIL, A1, A6 = VIH

Wait 10ms

00h

INCREMENT

CURRENT BLOCK

n = 0

CURRENT BLOCK = 0

Wait 4µs

W = VIL

++n

= 1000

START

YES

YESNO

NO LAST

BLOCK

YES

E = VIL

Wait 4µs

G = VIL

Wait 60ns

Read DATA

FAIL PASS

Verify Unprotect Set-upEnd

A9 = VIH

E, G = VIH A9 = VIH

E, G = VIH

M29W800DT, M29W800DB Block protection

49/52

Figure 20. In-system equipment block protect flowchart

AI03471

WRITE 60h

ADDRESS = BLOCK ADDRESS

A0 = VIL, A1 = VIH, A6 = VIL

n = 0

Wait 100µs

WRITE 40h

ADDRESS = BLOCK ADDRESS

A0 = VIL, A1 = VIH, A6 = VIL

RP = VIH ++n

= 25

START

FAIL

PASS

YES

DATA

01hYES

RP = VIH

Wait 4µs

Verify Protect Set-upEnd

READ DATA

ADDRESS = BLOCK ADDRESS

A0 = VIL, A1 = VIH, A6 = VIL

RP = VID

ISSUE READ/RESET

COMMAND

ISSUE READ/RESET

COMMAND

WRITE 60h

ADDRESS = BLOCK ADDRESS

A0 = VIL, A1 = VIH, A6 = VIL

Block protection M29W800DT, M29W800DB

50/52

Figure 21. In-system equipment c hip unprotect flowc hart

AI03472

WRITE 60h

ANY ADDRESS WITH

A0 = VIL, A1 = VIH, A6 = VIH

n = 0

CURRENT BLOCK = 0

Wait 10ms

WRITE 40h

ADDRESS = CURRENT BLOCK ADDRESS

A0 = VIL, A1 = VIH, A6 = VIH

RP = VIH

++n

= 1000

START

FAIL PASS

YES

DATA

00h

YESNO

RP = VIH

Wait 4µs

READ DATA

ADDRESS = CURRENT BLOCK ADDRESS

A0 = VIL, A1 = VIH, A6 = VIH

RP = VID

ISSUE READ/RESET

COMMAND

ISSUE READ/RESET

COMMAND

PROTECT ALL BLOCKS

INCREMENT

CURRENT BLOCK

LAST

BLOCK

YES

WRITE 60h

ANY ADDRESS WITH

A0 = VIL, A1 = VIH, A6 = VIH

Verify Unprotect Set-upEnd

M29W800DT, M29W800DB Revision history

51/52

10 Revision history

Table 29. Document revision history

Date Version Changes

August 2001 1.0 First issue

03-Dec-2001 2.0 Block protection appendix added, SO44 drawing and package

mechanical data updated, CFI Table 26, address 39h/72h data clarified,

read/reset operation during erase suspend clarified

01-Mar-2002 3.0

Description of Ready/Busy signal clarified (and Figure 14 modified)

Clarifi ed allowable commands during block erase

Clarifi ed the mode the device retur ns to in the CFI Read Query

command section

11-Apr-2002 4.0 Temperature range 1 added

Document promoted from preliminary data to full datasheet

31-Mar-2003 4.1

Erase suspend latency time (typic al and maximum) and data retention

parameters added to Table 6 : Program, erase times and program, erase

endurance cycles, and typical after 100k W/E cycles column removed.

Minimum voltage corrected for 70 ns speed class in Table 9: Operating

and AC measurement conditions.

Logic diagram and data toggle flowchart corrected.

Lead-free package options E and F added to Table 19: Ordering

inf ormation scheme.

13-Feb-2004 5

TSOP48 package outline and mechanical data updated.

TFBGA48 6 x 8 mm – 6 x 8 active ball array – 0.80 mm pitch added.

Table 9: Operating and A C measurement conditions updated for 70 ns

speed option.

23-Apr-2004 6 Figure 2: SO connections updated.

16-Sep-2004 7 45 ns speed class added.

21-Mar-2006 8 Removed TFBGA48 (ZA) (6 x 9 mm) package. Con verted to new ST

corporate template.

10-Dec-2007 9 Applied Numonyx branding.

25-Mar-2008 10 Minor text changes.

M29W800DT, M29W800DB

52/52

Please Read Carefully:

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH NUMONYX™ PRODUCTS. NO LICENSE, EXPRESS OR

IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT

AS PROVIDED IN NUMONYX'S TERMS AND CONDITION S OF SALE FOR SUCH PRODUCTS, NUMONYX ASSUMES NO LIABILIT Y

WHATSOEVER, AND NUMONYX DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF

NUMONYX PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE,

MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.

Numonyx products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility

applications.

Numonyx may make changes to specificati ons and product descri ptions at any time, without notice.

Numonyx, B.V. may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that rel ate to the

presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied,

by estoppel or otherwise, to any such patents, tradema rks, copyrights, or other intellectual property rights .

Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Numonyx reserves

these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them.

Contact your local Numonyx sale s office or your distributor to obtain the latest specifications and before placi ng your product order.

Copies of documents which have an order number and are referenced in this document, or other Numonyx literature may be obtained by

visiting Numonyx's website at http://www.numonyx.com.

Numonyx StrataFlash is a trademar k or registered trademark of Numonyx or its subsidiaries in the United States and other countries.

*Other names and brands may be claimed as the property of others.