IDC5F - SENSATA TECHNOLOGIES

One world. One KEMET

Overview

KEMET’s 900 Series encapsulated radial through-hole ceramic

disc capacitors are specically designed for interference-

suppression AC line ltering applications. Having internationally

recognized safety certications, these capacitors are well-suited

for applications that require keeping potentially disruptive or

damaging line transients and EMI out of susceptible equipment.

They are also an ideal solution in situations where there is a

need to suppress line disturbances at the source.

Safety Certied Capacitors are classied as either X and/or

Y capacitors. Class X capacitors are primarily used in line-to-

line (across-the-line) applications. In this application there is

no danger of electric shock to humans should the capacitor

fail, but could result in a risk of re. The class Y capacitor is

primarily used in line-to-ground (line by-pass) applications. In

this application, failure of the capacitor could lead to danger of

electric shock.

With a working voltage of 440 VAC in line-to-line (Class X) and

300 VAC in line-to-ground (Class Y) applications, these safety

capacitors meet the impulse test criteria outlined in IEC Standard

60384. Meeting subclass X1 and Y2 requirements, these devices

are certied to withstand impulses up to 4 KV (X1) and 5 KV (Y2)

respectively. These encapsulated devices also meet the ame test

requirements outlined in UL Standard 94V–0.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc,

Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Ordering Information

C9 7 1 U 472 M Z W D A A 7317

Ceramic

Series

Body

Diameter

Lead

Spacing

1,3 Spec.

Capacitance

Code (pF)

Capacitance

Tolerance

Rated

Voltage

Dielectric/

Temp. Char.

Design

Lead

Cong.

2,3

Failure

Rate

Packaging

(C-Spec)

2,3

C9 =

Ceramic

900

Series

0 = 7.0 mm

1 = 8.0 mm

2 = 9.0 mm

3 = 10.0 mm

4 = 11.0 mm

6 = 13.0 mm

8 = 15.0 mm

7 = 7.5 mm

1 = 10.0 mm

U =

Safety

2 signicant

digits +

Number of

zeroes

Use 9 for

1.0 -

9.9 pF

e.g., 2.2 pF

= 229

C = ±0.25 pF

D = ±0.5 pF

J = ±5%

K = ±10%

M = ±20%

Z = X1

440 VAC

/ Y2 300

VAC

N = CH

(NP0)

S = SL

Y = Y5P

W = Y5U

V = Y5V

D =

Disc

A =

Straight

B = Vertical

Kink

C =

Outside

Kink

D = Inside

Kink

A =

N/A

7317 = Ammo Pack

WL30 = Bulk/3.0 mm

Lead length

WL35 = Bulk/3.5 mm

Lead length

WL40 = Bulk/4.0 mm

Lead length

WL45 = Bulk/4.5 mm

Lead length

WL50 = Bulk/5.0 mm

Lead length

WL20 = Bulk/20 mm

Lead length

1 Capacitor body diameter will limit available lead spacing and packaging options. See "Dimensions" and "Product Ordering Codes and Ratings" sections of this

document to determine availability.

2 "Vertical Kink","Outside Kink" and "Inside Kink" lead congurations cannot be combined with the bulk/20 mm lead length option (WL20). 20 mm lead length is

only available on capacitors with straight leads (lead conguration ordering code "A"). For nonstandard lead length inquiries, please contact KEMET.

3 Bulk packaging lead length availability is dependent upon "Lead Conguration" and "Lead Spacing." See "Dimensions" section of this document to verify

availability of a specic lead length option. For nonstandard lead length inquiries, please contact KEMET.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Lead Congurations

Straight Vertical Kink Outside Kink Inside Kink

Dimensions – Millimeters

Lead

Cong.

Lead

Cong.

Ordering

Code1

FLead

Spacing

Tolerance

Packaging

Type2

LPackaging

C-Spec

Ordering

Code3

D T e Ød

Lead

Spacing2

Lead

Length

Body

Diameter2

Body

Thickness

Lead

Meniscus

Lead

Dia.

Straight A

7.5 ±1.0

Ammo Pack 20.0 +1.5/-1.0 7317

See Table 1 - "Product

Ordering Codes and

Ratings"

3.0

maximum 0.5 ±0.1

Bulk

3.0 ±1.0 WL30

4.5 ±1.0 WL45

5.0 ±1.0 WL50

10.0 ±1.0

Ammo Pack 20.0 +1.5/-1.0 7317

Bulk

3.0 ±1.0 WL30

4.5 ±1.0 WL45

5.0 ±1.0 WL50

Vertical Kink

(Preformed) B

7.5 ±1.0

Ammo Pack 18.0 +2.0/-0 7317

See Table 1 - "Product

Ordering Codes and

Ratings"

3.0

maximum 0.5 ±0.1

Bulk

3.5 ±1.0 WL35

4.0 ±1.0 WL40

10.0 ±1.0

Ammo Pack 18.0 +2.0/-0 7317

Bulk

3.5 ±1.0 WL35

4.0 ±1.0 WL40

1 Lead Conguration is identied in the 13th character of the ordering code. See "Lead Conguration" and "Ordering Information" sections of this document for

further details.

2 Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this document for

further details.

3 The "Packaging C-Spec" is a 4-digit numeric or alphanumeric code which identies both the packaging type and lead length requirement. When ordering, this

code must be included in the 15th through 18th character positions of the ordering code. See "Ordering Information" section of this document for further details.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Dimensions – Millimeters cont'd

1 Lead Conguration is identied in the 13th character of the ordering code. See "Lead Conguration" and "Ordering Information" sections of this document for

further details.

2 Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this document for

further details.

3 The "Packaging C-Spec" is a 4-digit numeric or alphanumeric code which identies both the packaging type and lead length requirement. When ordering, this

code must be included in the 15th through 18th character positions of the ordering code. See "Ordering Information" section of this document for further details.

Lead

Cong.

Lead

Cong.

Ordering

Code1

FLead

Spacing

Tolerance

Packaging

Type2

LPackaging

C-Spec

Ordering

Code3

D T e Ød

Lead

Spacing2

Lead

Length

Body

Diameter2

Body

Thickness

Lead

Meniscus

Lead

Dia.

Outside Kink

(Preformed) C

7.5 ±1.0

Ammo Pack 18.0 +2.0/-0 7317

See Table 1 - "Product

Ordering Codes and

Ratings"

3.0

maximum 0.5 ±0.1

Bulk

3.5 ±1.0 WL35

4.0 ±1.0 WL40

5.0 ±1.0 WL50

10.0 ±1.0

Ammo Pack 18.0 +2.0/-0 7317

Bulk

3.5 ±1.0 WL35

4.0 ±1.0 WL40

5.0 ±1.0 WL50

Inside Kink

(Preformed) D

7.5

±1.0

Ammo Pack 18.0 +2.0/-0 7317

13.0

maximum

7.0

maximum

3.0

maximum 0.5 ±0.1

Bulk 3.5 ±1.0 WL35

10.0

Ammo Pack 18.0 +2.0/-0 7317

Bulk 3.5 ±1.0 WL35

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Benets

• Safety Standard Recognized (IEC 60384-14)

• Reliable operation up to 125°C

• Class X1/Y2

• 7.5 mm and 10 mm lead spacing

• Lead (Pb)-free and RoHS Compliant

• Halogen Free

• Capacitance offerings ranging from 2.0 pF up to 10,000 pF

• Available capacitance tolerances of ±0.25 pF, ±0.5 pF, ±5%, ±10%, and ±20%

• High reliability

• Preformed (crimped) or straight lead congurations

• Non-polar device, minimizing installation concerns

• Encapsulation meets ammability standard UL 94V–0

Applications

Typical applications include:

• Line-to-line (Class X) ltering

• Line-to-ground (Class Y) ltering

• Antenna coupling

• Primary and secondary coupling (switching power supplies)

• Line disturbances suppression (motors and motor controls, relays, switching power supplies, and inverters)

Approval Standard and Certication No.

Safety Standard Standard No. Subclass Working Voltage Certicate No.

VDE

(ENEC) IEC 60384–14 X1 440 VAC 40036415

Y2 300 VAC

These devices are VDE/ENEC recognized for antenna coupling and AC line-to-line (Class X) and line-to-ground (Class Y) applications per IEC60384–14.

Environmental Compliance

These devices are Halogen Free and RoHS Compliant. They meet all requirements set forth by both EU and China RoHS directives.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

General Specications/Performance Characteristics

Dielectric/Temperature Characteristic: CH(NP0) SL Y5P Y5U Y5V

Operating Temperature Range -40°C to +125°C

Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC) ±60 ppm/ºC -1,000 ~ +350

ppm/ºC ±10% +20%/-55% ~ +30%/-80%

Dielectric Withstanding Voltage (7.5 mm and 10 mm Lead Spacing) 2,600 VAC

(60 ±5 seconds at 25ºC)

Quality Factor (Q) 30 pF% and above: ≥ 1,000

Below 30 pF: ≥ 400 +(20 x C)* See “Dissipation Factor”

Dissipation Factor (tanδ) at +25ºC1See “Quality Factor” 2.50% 2.50% 5.0%

Insulation Resistance (IR) Limit at +25°C 10,000 MΩ Minimum

(500 VDC applied for 60 ±5 seconds @ 25°C)

*C = Nominal capacitance

2 Capacitance and Dissipation Factor (DF) measured under the following conditions:

CH(NP0) & SL: 1 MHz ± 100 kHz and 1.0 ±0.2 Vrms

X5P, Y5U and Y5V: 1 kHz ± 50 Hz and 1.0 ±0.2 Vrms

Note: When measuring capacitance, it is important to ensure the set voltage level is held constant. The HP4284 & Agilent E4980 have a feature known as

Automatic Level Control (ALC). The ALC feature should be switched to "ON."

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 1 – Product Ordering Codes and Ratings

(1) To properly complete ordering code, insert the one-digit numeric code to reect required lead spacing: (Note that select capacitance values and packaging

options may limit lead spacing availability. See table above to verify availability.)

7 = 7.5 mm

1 = 10.0 mm

(2) To properly complete ordering code, insert the one-digit character code to reect the required lead conguration: (See "Lead Conguration" section of this

document, page 2, for further details.)

A = Straight

B = Vertical Kink

C = Outside Kink

D = Inside Kink

(3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this

document, page 2, for available options.

Dielectric/

Temp.

Char.

KEMET

Part Number Capacitance Capacitance

Tolerance

Dimensions (mm) Lead Spacing

Body

Diameter

(Maximum)

Body

Thickness

(Maximum)

Lead

Diameter

Bulk

Packaging

Ammo

Packaging

(NP0)

C90(1)U209CZND(2)A(3) 2.0 pF

±0.25 pF

7.0

5.0 0.5 ±0.1

7.5 mm

10 mm

C90(1)U309CZND(2)A(3) 3.0 pF

C90(1)U409CZND(2)A(3) 4.0 pF

C90(1)U509CZND(2)A(3) 5.0 pF

C90(1)U609DZND(2)A(3) 6.0 pF

±0.5 pF

C90(1)U709DZND(2)A(3) 7.0 pF

C90(1)U809DZND(2)A(3) 8.0 pF

C90(1)U909DZND(2)A(3) 9.0 pF

C90(1)U100DZND(2)A(3) 10 pF

C90(1)U120JZND(2)A(3) 12 pF

±5%

C90(1)U150JZND(2)A(3) 15 pF

C91(1)U180JZND(2)A(3) 18 pF

8.0

C91(1)U200JZND(2)A(3) 20 pF

C91(1)U220JZND(2)A(3) 22 pF

C91(1)U240JZND(2)A(3) 24 pF

C92(1)U270JZND(2)A(3) 27 pF

9.0C92(1)U300JZND(2)A(3) 30 pF

C92(1)U330JZND(2)A(3) 33 pF

C93(1)U360JZND(2)A(3) 36 pF 10.0

C93(1)U390JZND(2)A(3) 39 pF

C94(1)U470JZND(2)A(3) 47 pF 11.0

C90(1)U100JZSD(2)A(3) 10 pF

±5%

7.0

5.0 0.5 ±0.1

7.5 mm

10 mm

C90(1)U120JZSD(2)A(3) 12 pF

C90(1)U150JZSD(2)A(3) 15 pF

C90(1)U180JZSD(2)A(3) 18 pF

C90(1)U200JZSD(2)A(3) 20 pF

C90(1)U220JZSD(2)A(3) 22 pF

C90(1)U240JZSD(2)A(3) 24 pF

C90(1)U270JZSD(2)A(3) 27 pF

C90(1)U300JZSD(2)A(3) 30 pF

C90(1)U330JZSD(2)A(3) 33 pF

C90(1)U360JZSD(2)A(3) 36 pF

C90(1)U390JZSD(2)A(3) 39 pF

C90(1)U470JZSD(2)A(3) 47 pF

C90(1)U500JZSD(2)A(3) 50 pF

C90(1)U510JZSD(2)A(3) 51 pF

C91(1)U560JZSD(2)A(3) 56 pF

8.0

C91(1)U620JZSD(2)A(3) 62 pF

C91(1)U680JZSD(2)A(3) 68 pF

C91(1)U750JZSD(2)A(3) 75 pF

C92(1)U820JZSD(2)A(3) 82 pF 9.0

C93(1)U101JZSD(2)A(3) 100 pF 10.0

KEMET Part Number Capacitance

Capacitance

Tolerance

Body Diameter

(Maximum)

Body Thickness

(Maximum)

Lead Diameter Lead Spacing

Roll Over for

Order Info.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 1 – Product Ordering Codes and Ratings cont'd

(1) To properly complete ordering code, insert the one-digit numeric code to reect required lead spacing: (Note that select capacitance values and packaging

options may limit lead spacing availability. See table above to verify availability.)

7 = 7.5 mm

1 = 10.0 mm

(2) To properly complete ordering code, insert the one-digit character code to reect the required lead conguration: (See "Lead Conguration" section of this

document, page 2, for further details.)

A = Straight

B = Vertical Kink

C = Outside Kink

D = Inside Kink

(3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this

document, page 2, for available options.

Dielectric/

Temp.

Char.

KEMET

Part Number Capacitance Capacitance

Tolerance

Dimensions (mm) Lead Spacing

Body

Diameter

(Maximum)

Body

Thickness

(Maximum)

Lead

Diameter

Bulk

Packaging

Ammo

Packaging

Y5P

C90(1)U101KZYD(2)A(3) 100 pF

±10%

7.0

5.0 0.5 ±0.1

7.5 mm

10 mm

C90(1)U151KZYD(2)A(3) 150 pF

C90(1)U221KZYD(2)A(3) 220 pF

C90(1)U331KZYD(2)A(3) 330 pF

C90(1)U471KZYD(2)A(3) 470 pF

C91(1)U561KZYD(2)A(3) 560 pF 8.0

C91(1)U681KZYD(2)A(3) 680 pF

C92(1)U821KZYD(2)A(3) 820 pF 9.0

C92(1)U102KZYD(2)A(3) 1,000 pF

Y5U

C90(1)U102MZWD(2)A(3) 1,000 pF

±20%

7.0

5.0 0.5 ±0.1 7.5 mm or 10 mm

7.5 mm or 10 mm

C92(1)U152MZWD(2)A(3) 1,500 pF 9.0

C92(1)U222MZWD(2)A(3) 2,200 pF

C94(1)U332MZWD(2)A(3) 3,300 pF 11.0

C96(1)U392MZWD(2)A(3) 3,900 pF 13.0 10 mm only

C96(1)U472MZWD(2)A(3) 4,700 pF

Y5V

C90(1)U102MZVD(2)A(3) 1,000 pF

±20%

7.0

5.0 0.5 ±0.1 7.5 mm or 10 mm

7.5 mm or 10 mm

C90(1)U152MZVD(2)A(3) 1,500 pF

C90(1)U222MZVD(2)A(3) 2,200 pF

C92(1)U332MZVD(2)A(3) 3,300 pF 9.0

C94(1)U392MZVD(2)A(3) 3,900 pF 11.0

C94(1)U472MZVD(2)A(3) 4,700 pF

C96(1)U682MZVD(2)A(3) 6,800 pF 13.0 10 mm only

C98(1)U103MZVD(2)A(3) 10,000 pF 15.0

KEMET Part Number Capacitance

Capacitance

Tolerance

Body Diameter

(Maximum)

Body Thickness

(Maximum)

Lead Diameter Lead Spacing

Roll Over for

Order Info.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions

Item

Specication

Test Method

Operating Temperature Range -40ºC to +125ºC

Dielectric

Strength

Between lead

wires

No failures

The capacitor shall not be damaged when 2,600 VAC(rms) is applied

between the lead wires for 60 seconds.

Body Insulation No failures

The terminals (leads) of the capacitor shall

be connected together. A metal foil is tightly

wrapped around the body of the capacitor at a

distance of about 3 to 4 mm from each terminal.

The capacitor is then inserted into a container

lled with metal balls approximately 1 mm in

diameter. 2,600 VAC(rms) is applied for 60

seconds between the capacitor lead wires and

metal balls.

Insulation Resistance (IR) 10,000 MΩ minimum

The insulation resistance shall be measured with 500 ±50 VDC applied

after 60 ±5 seconds of charging.

Capacitance Within specied tolerance

Y5P, Y5U and Y5V: Capacitance is measured at 1 kHz ±20% and 5

Vrms or less. (20 ±2°C)

NP0 and SL: Capacitance is measured at 1 MHz ±20% and 1.0 ±0.2

Vrms (25°C)

Dissipation Factor (DF) or Q

Temperature

Characteristics Specication

Y5P, Y5U DF ≤ 2.5%

Y5V DF ≤ 5.0%

NP0,SL ≥ 30 pF: Q ≥ 1000

< 30 pF: Q ≥ 400

+(20 x C)

C = Nominal

capacitance

Temperature Characteristics

Temperature

Characteristics

Capacitance

Change

Y5P Within ±10%

Y5U Within +20%/-55%

Y5V Within ~+30%/-80%

CH 0 ±60 ppm/ºC

SL -1,000 ~+350 ppmºC

(+20ºC ~+85ºC)

A capacitance measurement is made at each step specied:

Step Temperature

1+20 ±2ºC

2-25 ±2ºC

3+20 ±2ºC

4 +85 ±2ºC

5+20 ±2ºC

Pre-treatment:

Capacitor is stored at 85 ±2ºC for 1 hour and then placed at room

condition

for 24 ±2 hours before measurement.

Terminal Strength

Tensile Lead wire or capacitor body shall not break.

With the termination in its normal position, the specimen is held by its

body in such a manner that the axis of the termination is vertical; a

tensile force of 10 N is applied to the termination in the direction of its

axis and acting in a direction away from the body of the specimen.

Bending Lead wire or capacitor body shall not break.

With the termination in its normal position, the specimen is held by its

body in such a manner that the axis of the termination is vertical; a

mass force of 5 N is then suspended from the end of the termination.

The body of the specimen is then inclined within a period of 2 to 3

seconds, through an angle of approximately 90° in the vertical plane

and then resumed to its initial position over the same period of time;

this operation constitutes one bend. One bend immediately followed by

a second bend in the opposite direction.

Solderability

Lead wire should have a uniform coating of

solder in the axial direction and over 3/4 of its

circumference.

The lead wire of the capacitor is dipped into molten solder for 2 ±0.5

seconds. The depth of immersion is up to 1.5 mm (+5/-0 mm) from the

root of lead wires.

Solder Temperature: Lead free solder (Sn-3Ag – 0.5Cu) 245°C ±5°C.

1 “Room Condition” is dened as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont'd

Item

Specication

Test Method

Soldering Effect

(Non-Preheat)

Appearance No visual defect

As shown in the gure below, the lead wires are immersed in molten

solder up to 1.5 mm (+5/-0 mm) from the end of the epoxy meniscus

(root of lead wire).

Duration/Solder Temperature: 3.5 ±0.5 seconds/350°C ±10°C or 10 ±1

seconds/260°C ±5°C

Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and then

placed at room condition1 for 24 ±2 hours before initial measurements.

Post-treatment: Capacitor is stored for 1 to 2 hours at room

condition

IR 1,000 MΩ

Dielectric

Strength

Per item 1

Capacitance

Y5P, Y5U and Y5V: Within ±10%

SL, CH (NP0): Within ±2.5% or ±0.25 pF,

whichever is larger.

Soldering Effect

(Preheat)

Appearance No visual defect Capacitor is stored at 120°C +0/-5°C for 60 +0/-5 seconds. Then, as

shown in the gure below, the lead wires are immersed in molten solder

up to 1.5 mm (+5/-0mm) from the end of the epoxy meniscus (root of

lead wire).

Duration/Solder Temperature: 7.5 +0/-1 seconds/260°C ±5°C

Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and then

placed at room condition1 for 24 ±2 hours before initial measurements.

Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1.

IR 1,000 MΩ

Dielectric

Strength

Per item 1

Capacitance

Y5P, Y5U and Y5V: Within ±10%

SL, CH (NP0): Within ±2.5% or ±0.25 pF,

whichever is larger.

Biased Humidity

Appearance No visual defect Steady State Humidity: Load Humidity:

Capacitance

Temperature

Characteristics

Capacitance

Change

Y5P Within ±10%

Y5U Within ±20%

Y5V Within ±30%

SL CH (NP0) Within ±2.5% or

±0.25 pF, whichever

is larger.

90 to 95% humidity at 40°C

±2°C for 500 ±12 hours.

Post Treatment:

Capacitor is stored for 1 to 2

hours at room condition1.

90 to 95% humidity at 40°C

±2°C for 500 ±12 hours with full

rated voltage applied.

Post Treatment:

Capacitor is stored for 1 to 2

hours at room condition1.

Y5P and Y5U: 5.0% maximum

Y5V: 7.5% maximum

SL and CH(NP0): Less than 30 pF:

Q ≥ 100 + 10 × C/3

More than 30 pF: Q ≥ 200

C = Nominal capacitance

Y5P, Y5V and Y5U: 3,000 MΩ minimum

SL and CH (NP0): 1,000 MΩ minimum

Dielectric

Strength

No failures

1 “Room Condition” is dened as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont'd

Item

Specication

Test Method

High Temperature

Life

Appearance No visual defect

Impulse Voltage: Each individual capacitor is subjected to three 5 kv

impulses prior to life testing.

0.9Vp

0.5Vp

Voltage

Time

(uS)

1.2

1.5

(uF)

0.01

0.1

Capacitors are placed in a circulating air oven for a period of 1,000

hours. The air in the oven is maintained at a temperature of 125°C ±2

throughout the test. The capacitors are subjected to AC 510 Vrms.

Each hour the voltage is increased to 1,000 Vrms for 0.1 seconds.

Capacitance

Change

Y5P, Y5V and Y5U: Within ±20%

SL and CH (NP0): Within ±3 or ±0.3 pF,

whichever is larger.

3,000 MΩ minimum

SL and CH (NPO): 1,000 MΩ minimum

Dielectric

Strength No failures

Flame Test

The capacitor ame extinguishes as follows:

Cycle Time

1 ~ 4 30 seconds maximum

560 seconds maximum

The capacitor is exposed to a ame for 15 seconds and then removed

for 15 seconds. This test is repeated for 5 cycles.

Active Flammability The cheesecloth should not ignite.

The capacitors are individually wrapped in at least one, but not more

than two, complete layers of cheesecloth. They are then subjected

to 20 discharges. The interval between successive discharges is 5

seconds. The VAC is maintained for 2 minutes after the last discharge.

1, 2

1 μF ±10% C

0.033 μF ±5% 10 kV

1-4

1.5 Mh ±20% 16A Rod core choke Cx Test capacitor

R100 ±2% V

VR ±5%

Ct 3 μF ±5% 10 kV V

Rated Voltage

F Fuse, Rated 10A Vt Voltage applied to Ct

1 “Room Condition” is dened as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont'd

Item

Specication

Test Method

Passive Flammability

The burning time should not exceed 30

seconds.

The tissue paper should not ignite.

The capacitor under test is held into a ame and in a position which

best promotes burning. Each specimen is exposed to the ame one

time.

Time of exposure to ame:

Length of ame:

Gas burner length:

Inside diameter:

Outside diameter:

Gas butane gas purity:

30 seconds

12 ±1 mm

35 mm minimum

0.5 ±0.1 mm

0.9 mm maximum

95% minimum

Temperature

Cycle

Appearance No visual defect

The capacitor is subjected to 5 temperature cycles.

(Temperature Cycle)

Step Temperature (°C) Time

(minutes)

1 -40 +0/-3 30

2Room temperature 3

3 125 +3/-0 30

4 Room temperature 3

Pre-treatment: Capacitor shall be stored at 85 ±2 for 1 hour then

placed at room condition1 for 24 ±2 hours.

Post-treatment: Capacitor is stored for 1 to 2 hours at room condition1.

Capacitance

Temperature

Characteristics

Capacitance

Change

SL, CH (NP0) Within ±5%

Y5P Within ±10%

Y5U, Y5V Within ±20%

DF/Q

SL, CH (NP0) ≥ 30 pF: Q ≥ 350

< 30 pF: Q ≥ 275

+5/2C

C = Nominal

capacitance

Y5P DF ≤ 5%

Y5U, Y5V DF ≤ 7.5%

IR 3,000 MΩ minimum

Dielectric

Strength

No failures

1 “Room Condition” is dened as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Soldering and Mounting Information

Soldering:

When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specication of the capacitor. Subjecting this

product to excessive heating could reow the solder joint between the lead and ceramic element and/or may result in thermal shocks

that can crack the ceramic element.

When soldering these capacitors with a soldering iron, it should be performed under the following conditions:

• Temperature of iron-tip: 400ºC maximum

• Soldering iron wattage: 50 W maximum

• Soldering time: 3.5 seconds maximum

Cleaning (ultrasonic cleaning):

To perform ultrasonic cleaning, observe the following conditions:

• Rinse bath capacity: Output of 20 watts per liter or less

• Rinsing time: 5 minute maximum

• Do not vibrate the PCB/PWB directly

• Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires

Construction

Reference

Item

Material

1Encapsulation1Epoxy resin, Pigment (Blue/UL 94 V–0)

2Dielectric Material BaTiO3

3Solder Sn 96.5, Ag 3, Cu 0.5

4Electrodes Ag (Glass frit)

5Lead Wires

Tinned copper clad steel wire

(Sn Plating 100% 3-7 µm)

1 The minimum thickness of the insulation coating (encapsulation) is 0.4 mm

Note: Image is exaggerated in order to clearly identify all components of construction.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Capacitor Marking

These capacitors shall be stamped or laser marked with KEMET's trademark, type designation, capacitor class, rated voltage, rated

capacitance, and capacitance tolerance codes. In addition, all devices are marked with the recognized approval mark and a date/lot

code for traceability. Marking will be supplied either on one side or both sides of the encapsulated capacitor body. All marking shall

be legible to allow for clear identication of the component. Marking appears in legible contrast. Illustrated below is an example of the

marking format and content. (Two sided marking is limited to capacitors with body diameters ≤ 8.0 mm.)

Location # Description Detail

❶KEMET Trademark

❷Type Designation

(2 characters) AC

❸Rated Capacitance

(3 numeric characters)

First two digits are the signicant gures of capacitance. Third digit indicates the additional

number of zeros. For example, 4,700 pF is identied as 472. (For values below 10 pF an “R” is

used in place of the decimal point, e.g., 2R0 = 2.0 pF.)

❹Capacitance Tolerance

Code (1 character) C = 0.25 pF, D = 0.5 pF, J = ±5%, K = ±10%, M = ±20%

❺VDE & ENEC approval mark

IEC 60384–14 3rd (2005)

❻Capacitor Class and Rated

Voltage X1: 440 V ~ Y2: 300 V ~

❼Date/Lot Code

Date/Lot Code, e.g., 3C12345

3 C 1 2345

Last digit of year,

e.g.,

3 = 2013

Manufacturing

Location Code

Manufacturing Month:

1-9 = Jan - Sept

A = October

N = November

D = December

Last 4 digits of

lot no.

Packaging Quantities

Packaging Type Loose (Bulk Bag) Carrier Tape Quantity

(12.7 mm Pitch1) (15 mm Pitch1)(25.4 mm Pitch1)

Ammo Pack

N/A

1,000 pieces/box

500 pieces/box

Bulk 500 pieces/bag N/A

1 For details regarding component pitch on carrier tape, see "Ammo Pack Taping Format" and "Ammo Pack Taping Specications" sections of this document.

AC472M

X1:440V~ Y2:300V~

2C12345

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Figure 1 - Ammo Pack Taping Format

5 mm and 7.5 mm Lead Spacing:

10 mm Lead Spacing:

Table 3 – Ammo Pack Taping Specications

1Prefromed (crimped) lead congurations include vertical kink, outside kink and inside kink. See "Lead Congurations" and "Ordering Information" sections of this

document for further details.

2Also referred to as "lead length" in this document.

Lead Spacing 5 mm 7.5 mm 10 mm

Lead Style Straight Preformed1Straight Preformed1Straight Preformed1

Item Symbol Dimensions (mm)

Lead Spacing F 5.0 +0.8/-0.2 7.5 ±1.0 10.0 ±1.0

Component Pitch P12.7 15.0 25.4 ±2

Sprocket Hole Pitch P

12.7 ±0.3 15.0 ±0.3 12.7 ±0.3

Sprocket Hole Center to

Component Center P26.35 ±1.5 7.5 ±1.5 12.7 ±1.5

Sprocket Hole Center to Lead Center P

3.75 ±1.0 3.75 ±1.0 7.7 ±1.5

Body Diameter D See "Product Ordering Codes and Ratings" section of this document.

Component Alignment (side/side) ∆S 0 ±2.0

Carrier Tape Width W 18.0 +1.0/-0.5

Sprocket Hole Position W

9.0 ±0.5

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Table 3 – Ammo Pack Taping Specications cont'd

1Prefromed (crimped) lead congurations include vertical kink, outside kink and inside kink. See "Lead Congurations" and "Ordering Information" sections of this

document for further details.

2Also referred to as "lead length" in this document.

Application Notes:

Storage and Operating Conditions:

The insulating coating of these devices does not form an air and moisture-tight seal. Avoid exposure to moisture and do not use or

store these devices in a corrosive atmosphere, especially where chloride gas, sulde gas, acid, alkali, salt, or the like are present.

Before cleaning, bonding or molding these devices, it is important to verify that your process does not affect product quality and

performance. KEMET recommends testing and evaluating the performance of a cleaned, bonded or molded product prior to

implementing and/or qualifying any of these processes. Store the capacitors where the temperature and relative humidity do not

exceed 40 degrees Centigrade and 70% respectively. For optimum solderability, capacitor stock should be used promptly, preferably

within 6 months of receipt.

Working Voltage:

Application voltage (Vp-p or Vo-p) must not exceed the voltage rating of the capacitor. Irregular voltages can be generated for a

transient period of time when voltage is initially applied and/or removed from a circuit. It is important to choose a capacitor with a

voltage rating greater than or equal to these irregular voltages.

Lead Spacing 5 mm 7.5 mm 10 mm

Lead Style Straight Preformed1Straight Preformed1Straight Preformed1

Item Symbol Dimensions (mm)

Height to Seating Plane2

(preformed leads1)H0N/A 18.0 +2.0/-0 N/A 18.0 +2.0/-0 N/A 18.0 +2.0/-0

Height to Seating Plane2

(straight leads) H20.0 +1.5/-1.0 N/A 20.0 +1.5/-1.0 N/A 20.0 +1.5/-1.0 N/A

Lead Protrusion ℓ 2.0 maximum

Diameter of Sprocket Hole D

4.0 ±0.2

Lead Diameter φd 0.5 ±0.1

Carrier Tape Thickness t

0.6 ±0.3

Total Thickness (Carrier Tape,

Hold-Down Tape and Lead) t21.5 maximum

Component Alignment (front/back )

∆h1

2.0 maximum

∆h2

Cut Out Length L 11.0 maximum

Hold-Down Tape Width W

11.0 minimum 11.5 minimum

Hold-Down Tape Position W

3.0 maximum 1.5 ±1.5

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Operating Temperature and Self-Generating Heat:

The surface temperature of a capacitor should be kept below the upper limit of its rated operating temperature range. Be sure to take

into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or similar

current, it may self-generate heat due to dielectric loss. Temperature rise due to self-generated heating should not exceed 20°C (while

operated at an atmosphere temperature of 25°C).

Handling - Vibration and Impact:

Do not expose these devices or their leads to excessive shock or vibration during use.

FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR

PARTIAL DISPERSION WHEN THE PRODUCT IS USED.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

KEMET Corporation

World Headquarters

2835 KEMET Way

Simpsonville, SC 29681

Mailing Address:

P.O. Box 5928

Greenville, SC 29606

www.kemet.com

Tel: 864-963-6300

Fax: 864-963-6521

Corporate Of ces

Fort Lauderdale, FL

Tel: 954-766-2800

North America

Southeast

Lake Mary, FL

Tel: 407-855-8886

Northeast

Wilmington, MA

Tel: 978-658-1663

Central

Novi, MI

Tel: 248-994-1030

West

Milpitas, CA

Tel: 408-433-9950

Mexico

Guadalajara, Jalisco

Tel: 52-33-3123-2141

Europe

Southern Europe

Paris, France

Tel: 33-1-4646-1006

Sasso Marconi, Italy

Tel: 39-051-939111

Central Europe

Landsberg, Germany

Tel: 49-8191-3350800

Kamen, Germany

Tel: 49-2307-438110

Northern Europe

Bishop’s Stortford, United Kingdom

Tel: 44-1279-460122

Espoo, Finland

Tel: 358-9-5406-5000

Asia

Northeast Asia

Hong Kong

Tel: 852-2305-1168

Shenzhen, China

Tel: 86-755-2518-1306

Beijing, China

Tel: 86-10-5829-1711

Shanghai, China

Tel: 86-21-6447-0707

Taipei, Taiwan

Tel: 886-2-27528585

Southeast Asia

Singapore

Tel: 65-6586-1900

Penang, Malaysia

Tel: 60-4-6430200

Bangalore, India

Tel: 91-806-53-76817

Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not

assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of

KEMET Electronics Corporation.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)

Other KEMET Resources

Tools

Resource Location

Con gure A Part: CapEdge http://capacitoredge.kemet.com

SPICE & FIT Software http://www.kemet.com/spice

Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask

Electrolytic LifeCalculator http://www.kemet.com:8080/elc

Product Information

Resource Location

Products http://www.kemet.com/products

Technical Resources (Including Soldering Techniques) http://www.kemet.com/technicalpapers

RoHS Statement http://www.kemet.com/rohs

Quality Documents http://www.kemet.com/qualitydocuments

Product Request

Resource Location

Sample Request http://www.kemet.com/sample

Engineering Kit Request http://www.kemet.com/kits

Contact

Resource Location

Website www.kemet.com

Investor Relations http://www.kemet.com/ir

Call Us 1-877-MyKEMET

Twitter http://twitter.com/kemetcapacitors

Disclaimer

All product speci cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and

verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.

All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.

Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are

not intended to constitute – and KEMET speci cally disclaims – any warranty concerning suitability for a speci c customer application or use. The Information is intended for use only

by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise

provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.

Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still

occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective

circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.

Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not

be required.

Radial Through-Hole Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Radial Disc, Encapsulated, AC Type, X1 440 VAC/Y2 300 VAC (Industrial Grade)