PS22A76 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 IntellimodTM Module Dual-In-Line Intelligent Power Module 25 Amperes/1200 Volts H G 1 2 3 H G H G 4 5 6 7 8 9 H G G 10 11 12 13 14 H H G J K G 15 16 17 18 41 19 Q G V 29 42 30 B R 31 L (5 PLACES) DEPTH 1.6 M (2 PLACES) 32 AB N AC S E 33 40 34 F F F D F F U AD F W T A AB Z X Description: DIPIPMs are intelligent power modules that integrate power devices, drivers, and protection circuitry. Design time is reduced by the use of application-specific HVICs and value-added features such as linear temperature feedback. Overall efficiency and reliability are increased by the use of full gate CSTBT technology and low thermal impedance. Q C Y W TERMINAL CODE 8 VPC 9 VP1 15 VPC 16 VWFB 3 VP1 10 VVFB 17 WPG 4 VUFB 5 (UPG) 11 VPG 12 VVFS 18 VWFS 19 VSC 6 VUFS 13 WP 20 UNG 7 VP 14 VP1 21 VN1 1 UP 2 (VPC) 29 WN 30 VNC 36 NU 37 W 24 CIN 31 WNG 38 V 25 CFO 26 FO 32 VNG 33 W 39 U 40 P 27 UN 34 NW 41 U 28 VN 35 NV 42 V 22 VNC 23 VOT Outline Drawing and Circuit Diagram Dimensions Inches Millimeters A 3.110.02 79.00.5 B 1.220.02 31.00.5 C 0.63 16.0 D 2.760.01 70.00.3 E 0.5 12.7 F 0.390.01 10.00.3 G 0.10.01 2.540.3 H 0.20.01 5.080.3 J 1.0 25.4 K 0.11 2.8 L 0.12 Dia. 2.9 Dia. M 0.180.01 Dia. 4.50.2 Dia. N 1.420.02 36.20.5 P 0.03 0.7 Rev. 08/09 Dimensions Q R S T U V W X Y Z AA AB AC AD Inches 0.08 0.66 0.44 015.0.04 0.082 0.086 0.31 0.07 0.34 0.03 0.10 0.48 0.39 0.068 Millimeters 2.0 16.73 11.13 3.81.0 2.1 2.2 8.0 1.8 8.6 0.8 2.7 12.33 10.12 1.75 Features: Low-loss, Full Gate CSTBT IGBTs Single Power Supply Integrated HVICs Direct Connection to CPU Applications: Variable Speed Pumps Variable Speed Compressors Small Motor Control Ordering Information: PS22A76 is a 1200V, 25 Ampere DIP Intelligent Power Module. 1 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 PS22A76 IntellimodTM Module Dual-In-Line Intelligent Power Module 25 Amperes/1200 Volts Absolute Maximum Ratings, Tj = 25C unless otherwise specified Characteristics Self-protection Supply Voltage Limit (Short Circuit Protection Capability)* Symbol PS22A76 Units VCC(prot.) 800 Volts Module Case Operation Temperature (See TC Measurement Point Below) TC -20 to 100 C Storage Temperature Tstg -40 to 125 C Mounting Torque, M4 Mounting Screws -- 13 in-lb Module Weight (Typical) -- 65 Grams VISO 2500 Volts Isolation Voltage, AC 1 minute, 60Hz Sinusoidal, Connection Pins to Heatsink Plate IGBT Inverter Sector Supply Voltage (Applied between P-NU, NV, NW) Supply Voltage, Surge (Applied between P-NU, NV, NW) Collector-Emitter Voltage (TC = 25C) Collector Current (TC = 25C) Peak Collector Current (TC = 25C, <1ms) VCC 900 Volts VCC(surge) 1000 Volts VCES 1200 Volts IC 25 Amperes ICP 50 Amperes Collector Dissipation (TC = 25C, per 1 Chip) PC 113.6 Watts Power Device Junction Temperature** Tj -20 to 150 C Control Sector Supply Voltage (Applied between VP1-VPC, VN1-VNC) VD 20 Volts VDB 20 Volts Input Voltage (Applied between UP, VP, WP-VPC, UN, VN, WN-VNC) VIN -0.5 ~ VD+0.5 Volts Fault Output Supply Voltage (Applied between FO-VNC) VFO -0.5 ~ VD+0.5 Volts Supply Voltage (Applied between VUFB-VUFS, VVFB-VVFS, VWFB-VWFS) Fault Output Current (Sink Current at FO Terminal) IFO 1 mA Current Sensing Input Voltage (Applied between CIN-VNC) VSC -0.5 ~ VD+0.5 Volts *VD = 13.5 ~ 16.5V, Inverter Part, Tj = 125C, Non-repetitive, Less than 2s **The maximum junction temperature rating of the power chips integrated within the DIPIPM is 150C (@Tf 100C). However, to ensure safe operation of the DIPIPM, the average junction temperature should be limited to Tj(avg) 125C (@Tf 100C). TC Measurement Point IGBT CHIP 1.2 TC POINT BUILT-IN HEATSINK 2 40.5 Rev. 08/09 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 PS22A76 IntellimodTM Module Dual-In-Line Intelligent Power Module 25 Amperes/1200 Volts Electrical and Mechanical Characteristics, Tj = 25C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units IC = 25A, Tj = 25C, VD = VDB = 15V, VIN = 5V -- 1.9 2.6 Volts IC = 25A, Tj = 125C, VD = VDB = 15V, VIN = 5V -- 2.0 2.7 Volts -- 2.5 3.0 Volts 0.8 1.5 2.2 s IGBT Inverter Sector Collector-Emitter Saturation Voltage Diode Forward Voltage Inductive Load Switching Times VCE(sat) VEC Tj = 25C, -IC = 25A, VIN = 0V ton trr VCC = 600V, VD = VDB = 15V, -- 0.3 -- s tC(on) IC = 25A, Tj = 125C, VIN = 0 5V, -- 0.6 0.9 s toff Inductive Load (Upper-Lower Arm) tC(off) Collector-Emitter Cutoff Current ICES -- 2.8 3.8 s -- 0.7 1.0 s VCE = VCES, Tj = 25C -- -- 1.0 mA VCE = VCES, Tj = 125C -- -- 10 mA VD = VDB = 15V, VIN = 5V, -- -- 3.70 mA -- -- 1.30 mA -- -- 3.50 mA -- -- 1.30 mA 4.9 -- -- Volts Control Sector Circuit Current ID Total of VP1-VPC, VN1-VNC VD = VDB = 15V, VIN = 5V, VUFB-VUFS, VVFB-VVFS, VWFB-VWFS VD = VDB = 15V, VIN = 0V, Total of VP1-VPC, VN1-VNC VD = VDB = 15V, VIN = 0V, VUFB-VUFS, VVFB-VVFS, VWFB-VWFS Fault Output Voltage Input Current Short-Circuit Trip Level* VFOH VSC = 0V, FO Terminal Pull-up to 5V by 10k VFOL VSC = 1V, IFO = 1mA -- -- 1.1 Volts IIN VIN = 5V 0.7 1.5 2.0 mA ISC -20C TC 100C, VD = 15V 42.5 -- -- Amps Supply Circuit Undervoltage UVDBt Trip Level, TC 100C 10.0 -- 12.0 Volts Protection UVDBr Reset Level, TC 100C 10.5 -- 12.5 Volts UVDt Trip Level, TC 100C 10.3 -- 12.5 Volts UVDr Reset Level, TC 100C 10.8 -- 13.0 Volts tFO CFO = 22nF 1.6 2.4 -- ms ON Threshold Voltage Vth(on) Applied between UP, VP, WP-VPC, -- -- 3.5 Volts OFF Threshold Voltage Vth(off) UN, VN, WN-VNC 0.8 -- -- Volts Temperature Output*** VOT At LVIC Temperature = 85C 3.50 3.63 3.76 Volts Fault Output Pulse Width** * Short-Circuit protection is functioning only at the lower arms. Please select the value of the external shunt resistor such that the SC trip level is less than 85A. **Fault signal is asserted when the lower arm short circuit or control supply under-voltage protective functions operate. The fault output pulse-width tFO depends on the capacitance value of CFO according to the following approximate equation: CFO = (12.2 x 10-6 x tFO [F]). ***When the temperature rises excessively, the controller (MCU) should stop the DIPIPM. Rev. 08/09 3 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 PS22A76 IntellimodTM Module Dual-In-Line Intelligent Power Module 25 Amperes/1200 Volts Thermal Characteristics, Tj = 25C unless otherwise specified Characteristic Min. Typ. Max. Units Thermal Resistance Junction to Case Rth(j-C)Q Symbol IGBT Part (Per 1/6 Module) Condition -- -- 0.88 C/Watt Thermal Resistance Junction to Case Rth(j-C)D FWDi Part (Per 1/6 Module) -- -- 1.25 C/Watt Recommended Conditions for Use Characteristic Supply Voltage Control Supply Voltage Min. Typ. Max. VCC Symbol Applied between P-NU, NV, NW Condition 350 600 800 Volts Units VD Applied between VP1-VPC, VN1-VNC 13.5 15.0 16.5 Volts VDB Applied between VUFB-VUFS, 13.0 15.0 18.5 Volts -1 -- 1 V/s -- s kHz VVFB-VVFS, VWFB-VWFS Control Supply Variation Arm Shoot-through VD, VDB tDEAD For Each Input Signal, TC 100C 3.3 -- PWM Input Frequency fPWM TC 100C, Tj 125C -- -- 15 Allowable rms Current* IO VCC = 600V, VD = 15V, -- -- 5.5 Arms -- -- -- s Blocking Time fC = 15kHz, PF = 0.8, Sinusoidal PWM, Tj 125C, TC 100C Minimum Input PWIN(on)** Pulse Width PWIN(off)*** IC 25A 350 VCC 800V, 13.5 VD 16.5V, -- -- -- s 25 IC 42.5A 13.5 VDB 16.5V, -20C TC 100C, -- -- -- s VNC Between VNC-NU, NV, NW (Including Surge) -5.0 -- 5.0 Volts N-line Wiring Inductance Less Than 10nH VNC Variation * The allowable rms current value depends on the actual application conditions. **If input signal ON pulse is less than PWIN(on), the device may not respond. ***The IPM may fail to respond to an ON pulse if the preceeding OFF pulse is less than PWIN(off). Delayed Response Against Shorter Input OFF Signal Than PWIN(off), P-side only P-SIDE CONTROL INPUT INTERNAL IGBT GATE OUTPUT CURRENT IC t2 t1 Solid Line - OFF Pulse Width > PWIN(off): Turn ON time t1. Dotted Line - OFF Pulse Width < PWIN(off): Turn ON time t2. 4 Rev. 08/09 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 PS22A76 IntellimodTM Module Dual-In-Line Intelligent Power Module 25 Amperes/1200 Volts Application Circuit IGBT1 UP VP1 C2 D1 C1 + HVIC1 FWDi1 VUFB C2 DZ1 U VUFS IGBT2 VP VP1 C2 D1 C1 + HVIC2 FWDi2 VVFB C2 DZ1 V VVFS MCU C2 D1 + VPC VWFB C2 DZ1 M + IGBT3 WP VP1 C1 P C5 FWDi3 HVIC3 C3 C3 W VWFS UN R2 C4 R2 C4 R2 C4 VD FWDi4 NU WN CFO R3 FO VOT IGBT5 LVIC C2 FWDi5 NV IGBT6 VN1 15V C1 + DZ1 IGBT4 VN VNO VNC FWDi6 NW VSC CIN CSF Component Selection: Dsgn. Typ. Value D1 1A, 600V DZ1 24V, 1W C1 10-100F, 50V C2 0.22-2.0F, 50V C3 200 to 2500F, 450V C4 100pF, 50V C5 0.1-0.22F, 1000V CSF 1000pF, 50V RSF 1.8k RSHUNT 20ohm-500ohm R1 1-10 R2 330 R3 10k B D RSF C RSHUNT A Description Control and boot strap supply overvoltage suppression Control and boot strap supply over voltage suppression Boot strap supply reservoir - electrolytic long lifem low impedance, 105C Local decoupling/High frequency noise filters - multilayer ceramic (Note 4) Main DC bus filter capacitor - electrolytic, long life, high ripple current, 105C Optional input signal noise filter - multilayer ceramic (Note 11) Surge voltage suppression (Note 2) Short circuit detection filter capacitor - multilayer ceramic Short circuit detection filter resistor Current sensing resistor Boot strap supply inrush limiting resistor - non-inductive, temperature stable, tight tolerance (Note 5) Optional input signal noise filter (Note 11) Fault signal pull-up resistor (Note 9) Notes: 1) If control GND is connected to power GND by broad pattern, it may cause malfunction by power GND fluctuation. It is recommended to connect control GND at only a point at which NU, NV, NW are connected to power GND line. 2) To prevent surge destruction, the wiring between the smoothing capacitor and the P-N1 terminals should be as short as possible. Generally inserting a 0.1 ~ 0.22F snubber capacitor C3 between the P-N1 terminals is recommended. 3) The time constant R1,C4 of RC filter for preventing the protection circuit malfunction should be selected in the range of 1.5 ~ 2s. SC interrupting time might vary with the wiring pattern. Tight tolerance, temp-compensated type is recommended for R1,C4. 4) All capacitors should be mounted as close to the terminals of the DIPIPM as possible. (C1: good temperature, frequency characteristics electrolytic type, and C2 : good temperature, frequency and DC bias characteristic ceramic type are recommended.) 5) It is recommended to insert a Zener diode DZ1 (24V/1W) between each pair of control supply terminals to prevent surge destruction. 6) To prevent erroneous SC protection, the wiring from VSC terminals to CIN filter should be divided at the point D that is close to the terminal of sense resistor and the wiring should be patterned as short as possible. 7) For sense resistor, the variation within 1% (including temperature characteristics), low inductance type is recommended. 1/8W is recommended, but an evaluation of your system is recommended. 8) To prevent erroneous operation, wiring A, B, and C should be as short as possible. 9) FO output is open drain type. It should be pulled up to the positive side of 5V or 15V power supply with a resistor that limits FO sink current (IFO) under 1mA. (Over 5.1k is needed and 10k is recommended for 5V supply.) 10) Error signal output width (tFO) can be set by the capacitor connected to the CFO terminal. tFO(typ) = CFO / 9.1 x 10-6 (s). 11) Input drive is high-active type. There is a 3.3k pull-down resistor integrated in the IC input circuit. To prevent malfunction, the wiring of each input should be patterned as short as possible. When inserting the RC filter, make sure the input signal level meets the turn-on and turn-off threshold voltage. Thanks to HVIC inside the module, connection to the MCU may be direct or with an opto-coupler. Rev. 08/09 5 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 PS22A76 IntellimodTM Module Dual-In-Line Intelligent Power Module 25 Amperes/1200 Volts Protection Function Timing Diagrams Short Circuit Protection (N-side Only with External Shunt Resistor and RC Filter) a6 N-SIDE CONTROL INPUT a7 SET PROTECTION CIRCUIT STATE INTERNAL IGBT GATE RESET a3 a2 SC a1 a8 a4 OUTPUT CURRENT IC SC REFERENCE VOLTAGE SENSE VOLTAGE OF RS FAULT OUTPUT FO a5 RC CIRCUIT TIME CONSTANT DELAY a1: a2: a3: a4: a5: a6: a7: a8: Normal operation - IGBT turns on and carries current. Short circuit current is detected (SC trigger). All N-side IGBT's gate are hard interrupted. All N-side IGBT's turn off. FO output wirh a fixed pulse width (determined by the external capacitance CFO). Input "L" - IGBT off. Input "H" - IGBT on, but during the FO output perid the IGBT will not turn on. IGBT turns on when LH signal is input after FO is reset. Under-Voltage Protection (N-side , UVD) CONTROL INPUT PROTECTION CIRCUIT STATE UVDr CONTROL SUPPLY VOLTAGE VD SET RESET b1 UVDt b2 RESET b6 b3 b4 b7 OUTPUT CURRENT IC FAULT OUTPUT FO b5 b1: Control supply voltage VD rises - After VD level reaches under voltage reset level (UVDr), the circuits start to operate when next input is applied. b2 : Normal operation - IGBT turns on and carries current. b3: VD level dips to under voltage trip level (UVDt). b4: All N-side IGBT's turn off in spite of control input condition. b5: FO is low for a minimum period determined by the capacitance CFO but continuously during UV period. b6: VD level reaches UVDr. b7: Normal operation - IGBT turns on and carries current. 6 Rev. 08/09 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 PS22A76 IntellimodTM Module Dual-In-Line Intelligent Power Module 25 Amperes/1200 Volts Protection Function Timing Diagrams Under-Voltage Protection (P-side, UVDB) CONTROL INPUT PROTECTION CIRCUIT STATE CONTROL SUPPLY VOLTAGE VDB SET RESET UVDBr UVDt c1 RESET c5 c3 c4 c2 c6 OUTPUT CURRENT IC FAULT OUTPUT FO HIGH LEVEL (NO FAULT OUTPUT) c1: Control supply voltage VDB rises - After VDB level reaches under voltage reset level (UVDBr), the circuits starts to operate when next input is applied. c2: Normal operation - IGBT turns on and carries current. c3: VDB level dips to under voltage trip level (UVDBt). c4: P-side IGBT turns off in spite of control input signal level, but there is no FO signal output. c5: VDB level reaches UVDBr. c6: Normal operation - IGBT on and carries current. Typical Interface Circuit 5V LINE DIP-IPM 10k UP, VP, WP, UN, VN, WN MCU 2.5k (MIN) FO NOTE: RC coupling at each input (parts shown dotted) may change depending on the PWM control scheme used in the application and the wiring impedance of the printed circuit board. The DIPIPM input signal section integrates a 2.5k (min) pull-down resistor. Therefore, when using an external filtering resistor, care must be taken to satisfy the turn-on threshold voltage requirement. VNC (LOGIC) Wiring Method Around Shunt Resistor It is recommended to make the inductance under 10nH. For shunt resistors, it is recommended to use as low inductance type as possible. Shunt Resistors DIPIPM NU NV VNC Connect the wiring from VNC terminal at the point as close to shunt resistors' terminal as possible. NW To Current Detecting Circuit Rev. 08/09 It is recommended to divide the wiring to current detecting circuit at the point as close to shunt resistor's terminal as possible. 7 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 PS22A76 IntellimodTM Module Dual-In-Line Intelligent Power Module 25 Amperes/1200 Volts FREE-WHEEL DIODE FORWARD CHARACTERISTICS (TYPICAL) 3.0 2.5 2.0 1.5 1.0 0.5 0 20 40 60 VIN = 5V Tj = 25C Tj = 125C 0.5 0 0 20 40 100 100 60 101 102 REVERSE RECOVERY CHARACTERISTICS (TYPICAL - N-SIDE) SWITCHING TIME (ON) VS. COLLECTOR CURRENT (TYPICAL - N-SIDE) SWITCHING TIME (OFF) VS. COLLECTOR CURRENT (TYPICAL - N-SIDE) 101 SWITCHING TIME, ton, (s) REVERSE RECOVERY TIME, trr, (s) 1.0 101 COLLECTOR RECOVERY CURRENT, -IC, (AMPERES) 10-1 VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C 101 102 101 VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C 100 10-1 100 101 100 VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C 10-1 100 102 101 102 COLLECTOR RECOVERY CURRENT, -IC, (AMPERES) COLLECTOR CURRENT, IC, (AMPERES) COLLECTOR CURRENT, IC, (AMPERES) SWITCHING TIME (ON) VS. COLLECTOR CURRENT (TYPICAL - N-SIDE) SWITCHING TIME (OFF) VS. COLLECTOR CURRENT (TYPICAL - N-SIDE) SWITCHING LOSS (ON) VS. COLLECTOR CURRENT (TYPICAL - N-SIDE) 101 101 VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C SWITCHING TIME, tc(off), (s) SWITCHING TIME, tc(on), (s) 1.5 VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C COLLECTOR RECOVERY CURRENT, -IC, (AMPERES) 10-2 100 10-1 10-2 100 101 102 102 100 10-1 COLLECTOR CURRENT, IC, (AMPERES) 8 2.0 REVERSE RECOVERY CHARACTERISTICS (TYPICAL - N-SIDE) COLLECTOR-CURRENT, IC, (AMPERES) 100 100 2.5 SWITCHING TIME, toff, (s) 0 3.0 REVERSE RECOVERY CURRENT, Irr, (AMPERES) VD = VDB = 15V VIN = 5V Tj = 25C Tj = 125C 102 SWITCHING LOSS, PSW(on), (mJ/PULSE) COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) 3.5 EMITTER-COLLECTOR VOLTAGE, VEC, (VOLTS) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C 10-2 100 101 COLLECTOR CURRENT, IC, (AMPERES) 102 101 VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C 100 10-1 100 101 102 COLLECTOR CURRENT, IC, (AMPERES) Rev. 08/09 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697 (724) 925-7272 PS22A76 IntellimodTM Module Dual-In-Line Intelligent Power Module 25 Amperes/1200 Volts VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C 100 10-1 100 101 101 10-1 100 102 101 102 COLLECTOR RECOVERY CURRENT, -IC, (AMPERES) SWITCHING TIME (ON) VS. COLLECTOR CURRENT (TYPICAL - P-SIDE) SWITCHING TIME (OFF) VS. COLLECTOR CURRENT (TYPICAL - P-SIDE) SWITCHING TIME (ON) VS. COLLECTOR CURRENT (TYPICAL - P-SIDE) 10-1 100 101 102 VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C 10-1 100 SWITCHING TIME (OFF) VS. COLLECTOR CURRENT (TYPICAL - P-SIDE) 101 102 100 100 VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C 101 COLLECTOR CURRENT, IC, (AMPERES) 102 101 VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C 10-1 10-2 100 101 COLLECTOR CURRENT, IC, (AMPERES) COLLECTOR CURRENT, IC, (AMPERES) SWITCHING LOSS (ON) VS. COLLECTOR CURRENT (TYPICAL - P-SIDE) SWITCHING TIME (OFF) VS. COLLECTOR CURRENT (TYPICAL - P-SIDE) 102 102 102 SWITCHING LOSS, PSW(on), (mJ/PULSE) 101 SWITCHING TIME, tc(on), (s) SWITCHING TIME, toff, (s) 101 100 COLLECTOR CURRENT, IC, (AMPERES) Rev. 08/09 VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C 100 101 10-2 100 REVERSE RECOVERY CHARACTERISTICS (TYPICAL - P-SIDE) COLLECTOR RECOVERY CURRENT, -IC, (AMPERES) 100 SWITCHING TIME, tc(off), (s) 101 101 COLLECTOR CURRENT, IC, (AMPERES) VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C 10-1 VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C 100 100 102 101 SWITCHING TIME, ton, (s) REVERSE RECOVERY CHARACTERISTICS (TYPICAL - P-SIDE) VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C SWITCHING LOSS, PSW(off), (mJ/PULSE) 101 102 REVERSE RECOVERY CURRENT, Irr, (AMPERES) SWITCHING LOSS, PSW(off), (mJ/PULSE) 102 REVERSE RECOVERY TIME, trr, (s) SWITCHING TIME (OFF) VS. COLLECTOR CURRENT (TYPICAL - N-SIDE) 100 10-1 100 101 COLLECTOR CURRENT, IC, (AMPERES) 102 101 VCC = 600V VD = VDB = 15V VIN = 0V 5V L = 1mH Tj = 25C Tj = 125C 100 10-1 100 101 102 COLLECTOR CURRENT, IC, (AMPERES) 9