Product Specification Multi-rate CWDM Pluggable SFP Transceiver FWLF15217Dxx PRODUCT FEATURES * Up to 2.67 Gb/s bi-directional data links * Hot-pluggable SFP footprint * Built-in digital diagnostic functions * Uncooled DFB laser transmitter in 8 possible CWDM wavelengths * Duplex LC connector * Very low jitter * Metal enclosure, for lower EMI * Single 3.3V power supply APPLICATIONS * Low power dissipation <700mW * * Operating temperature range: 0C to 70C Metro Access Rings and Point-to-Point networking for SONET, Gigabit Ethernet and Fibre Channel Finisar's FWLF15217Dxx CWDM Small Form Factor Pluggable (SFP) transceivers are designed for operation in Metro Access Rings and Point-to-Point networks using SONET, Gigabit Ethernet and Fibre Channel networking equipment. They are available in eight different CWDM wavelengths. Digital diagnostics functions are available via an I2C serial bus. In addition, they comply with the Small Form Factor Pluggable MultiSourcing Agreement (MSA)1. PRODUCT SELECTION Wavelength Xx 1471 nm 1491 nm 1511 nm 1531 nm 47 49 51 53 Clasp Color Code Gray Violet Blue Green Finisar Corporation August 2015 Rev. C1 Wavelength xx 1551 nm 1571 nm 1591 nm 1611 nm 55 57 59 61 Clasp Color Code Yellow Orange Red Brown Page 1 FWLF15217Dxx SFP Product Specification I. Pin Descriptions Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Symbol VEET TFAULT TDIS MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) Rate Select LOS VEER VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ 19 20 TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Not supported. Transmitter Disable. Laser output disabled on high or open. Module Definition 2. Data line for Serial ID. Module Definition 1. Clock line for Serial ID. Module Definition 0. Grounded within the module. No connection required Loss of Signal indication. Logic 0 indicates normal operation. Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. 100 ohm termination between TD+ and TD-, AC Coupled thereafter. Transmitter Inverted DATA in. See TD+ Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 3 3 4 5 1 1 1 1 1 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 3. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 5.5V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. Finisar 2x receiver achieves simultaneous 1x and 2x operation without active control. 5. LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 5.5V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. Towards Bezel 1 VeeT 2 TXFault 3 TX Disable 4 MOD-DEF(2) 5 MOD-DEF(1) 6 MOD-DEF(0) 7 Rate Select 8 LOS 9 VeeR 10 VeeR VeeT 20 TD- 19 TD+ 18 VeeT 17 VccT 16 VccR 15 VeeR 14 RD+ 13 RD- 12 VeeR 11 Towards ASIC Diagram of Host Board Connector Block Pin Numbers and Names Finisar Corporation August 2015 Rev. C1 Page 2 FWLF15217Dxx SFP Product Specification II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature III. Symbol Vcc TS TOP Min -0.5 -40 0 Typ Max 4.7 85 70 Unit V C C Ref. Max 3.60 300 Unit V mA Ref. 1 1200 Vcc Vee+ 0.8 10 mV V V us mV ps ps V V mVpp 3 4 4 5 5 6 Electrical Characteristics (TOP = 0 to 70 C, VCC = 3.15 to 3.60 Volts) Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Single ended data output swing Data output rise time Data output fall time LOS Fault LOS Normal Power Supply Rejection Symbol Vcc Icc Rin Vin,pp VD VEN Vout,pp tr tf VLOS fault VLOS norm PSR Min 3.15 Typ 200 100 250 Vcc - 1.3 Vee 250 100 100 Vcc - 0.5 Vee 100 800 175 175 VccHOST Vee+0.5 2 Notes: 1. Connected directly to TX data input pins. AC coupled thereafter. 2. Or open circuit. 3. Into 100 ohms differential termination. 4. 20 - 80 % 5. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 6. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network. Finisar Corporation August 2015 Rev. C1 Page 3 FWLF15217Dxx SFP Product Specification IV. Low Speed Signals Parameter RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis RX_LOS Assert Delay t_loss_on 100 RX_LOS Negate Delay t_loss_off 100 TX_DISABLE Assert Time t_off 10 TX_DISABLE Negate Time t_on 1000 TX_DISABLE Reset Time Symbol Min -30 Typ 0.5 2 Max -19 t_reset 10 TX_FAULT Assert 100 Initialization Time 300 Finisar Corporation August 2015 Rev. C1 Units Notes/Conditions dBm dBm dB sec From detection of loss of signal to assertion of RX_LOS sec From detection of presence of signal to negation of RX_LOS sec Rising edge of TX_DISABLE to fall of output signal below 10% of nominal sec Falling edge of TX_DISABLE to rise of output signal above 90% of nominal. Time indicated is under steady-state temperature conditions. sec TX_DISABLE HIGH before TX_DISABLE set LOW sec From fault to assertion of TX_FAULT msec From power on to negation of TX_FAULT using TX_DISABLE Page 4 FWLF15217Dxx SFP Product Specification V. Optical Characteristics (TOP = 0 to 70 C, VCC = 3.15 to 3.60 Volts) Parameter Transmitter Output Opt. Pwr (End of Life) Optical Wavelength Wavelength Temperature Dependance Spectral Width (-20dB) Optical Extinction Ratio Sidemode Supression ratio Optical Rise/Fall Time RIN Transmitter Jitter Generation Dispersion Penalty at 50km Receiver Optical Input Power Optical Center Wavelength LOS De-Assert LOS Assert LOS Hysteresis Receiver Jitter Generation @2.488Gbps Receiver Jitter Generation @1.25Gbps Dispersion Penalty at 60km Symbol Min POUT +0 (x-6.5) ER SSRmin tr/ tf RIN 8.2 30 Pin C LOSD LOSA Typ Max Unit (x) 0.08 +5 (x+6.5) 0.125 1 dBm nm nm/C nm dB dB ps dB/Hz mUI dB 180 -120 75 1.5 -20 1270 0 1620 -19 -30 1.0 130 160 2 dBm nm dBm dBm dB ps ps dB Ref. 1 2 3 6 7 8 Notes: 1. Class 1 Laser Safety per FDA/CDRH and IEC-825-1 regulations. 2. Over case temperature of 0 to 70 C. The Transmitter Center Wavelength "x" is as specified by the customer. The current available wavelengths are: 1470, 1490, 1510, 1530, 1550, 1570, 1590, and 1610 nm. Please see the "Product Selection" section on page 1. 3. Unfiltered 4. Worst-case extinction ratio. Measured with a PRBS 223-1 test pattern, @2.67Gb/s, BER<10 -12, EOL 5. 6. Worst-case extinction ratio. Measured with a PRBS 27-1 test pattern, @1.25Gb/s, BER<10 -12, EOL Jitter added by receiver (peak to peak). Measured at Average Rx Sensitivity of -20dBm, PRBS 231-1 test pattern. Jitter added by receiver (peak to peak). Measured at Average Rx Sensitivity of -23dBm, PRBS 27-1 test pattern. 7. 8. V. Measured using 9/125m SMF-28 @2.488Gbps, PRBS 223-1 test pattern, BER<10 -10. General Specifications Parameter Data Rate Total System Budget Symbol BR -- Finisar Corporation August 2015 Rev. C1 Min 0.622 20 Typ 21.0 Max 2.67 Units Ref. Gb/sec dB @2.67 Gb/s, BER < 10-12 Page 5 FWLF15217Dxx SFP Product Specification w/ PRBS 223-1. VI. Environmental Specifications Finisar CWDM SFP transceivers have an operating temperature range from 0C to +60C case temperature. Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min 0 -40 Typ Max 70 85 Units C C Ref. Regulatory Compliance Finisar CWDM SFP transceivers are Class 1 Laser Products. They are certified per the following standards: Feature Laser Eye Safety Agency FDA/CDRH Laser Eye Safety TUV Electrical Safety CSA Standard CDRH and IEC-825 Class 1 Laser Product. See Note 1 EN 60950 EN 60825-1 EN 60825-2 CLASS 3862.07 CLASS 3862.87 Note 1: Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001. Finisar Corporation August 2015 Rev. C1 Page 6 FWLF15217Dxx SFP Product Specification VIII. Digital Diagnostic Functions Finisar FWLF15217Dxx SFP transceivers support the 2-wire serial communication protocol as defined in the draft SFP MSA1. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver's capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN2030: "Digital Diagnostics Monitoring Interface for SFP Optical Transceivers". Finisar Corporation August 2015 Rev. C1 Page 7 FWLF15217Dxx SFP Product Specification IX. Mechanical Specifications Finisar's Multi-rate CWDM Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA). FWLF15217Dxx (dimensions are in inches) Finisar Corporation August 2015 Rev. C1 Page 8 FWLF15217Dxx SFP Product Specification X. PCB Layout and Bezel Recommendations Finisar Corporation August 2015 Rev. C1 Page 9 FWLF15217Dxx SFP Product Specification Finisar Corporation August 2015 Rev. C1 Page 10 FWLF15217Dxx SFP Product Specification XI. References 1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available at Finisar upon request. 2. Bellcore GR-253 and ITU-T G.957 Specifications. 3. IEEE Std 802.3. IEEE Standards Department, 2000.(*) 4. "Fibre Channel Draft Physical Interface Specification (FC-PI 10.0)". American National Standard for Information Systems.(*) (*) Neither IEEE 802.3 nor FC-PI 10.0 specifies a 15xx nm DFB single mode interface. The FWLF15217Dxx complies with these specifications except for the following optical parameters, which have different values: transmitter wavelength, receiver sensitivity, and transmit output power. See Section IV for details. XII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com Finisar Corporation August 2015 Rev. C1 Page 11