Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is as of October 2012. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification. Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is available. Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called TAIYO YUDEN s official sales channel ). It is only applicable to the products purchased from any of TAIYO YUDEN s official sales channel. Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights. Caution for export Certain items in this catalog may require specific procedures for export according to Foreign Exchange and Foreign Trade Control Law of Japan, U.S. Export Administration Regulations , and other applicable regulations. Should you have any question or inquiry on this matter, please contact our sales staff. 13 LEADED FERRITE BEAD INDUCTORS(FB SERIES A TYPE / R TYPE) LEADED FERRITE BEAD INDUCTORS (FB SERIES A TYPE / R TYPE) WAVE PARTS NUMBER F B A 0 4 Series name Code FB Shape Code A R H A 4 5 0 B B Series name Ferrite bead Shape Axial lead Radial lead FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS Dimensions of coreD Code Dimensions of coreDmm 03 2.5 04 3.5 05 5.0 06 6.0 07 7.5 Material Code HA VA Nominal impedance Code example 850 121 Material Refer to impedance curves for material differences 0 0 Blank space Lead configuration Code Lead configurations AB Straight lead (26mm lead space) / ammo BB Straight lead (52mm lead space) / ammo KD Formed lead (10mm pitch) / bulk KE Formed lead (12.5mm pitch) / bulk KF Formed lead / bulk (15.0mm pitch) / bulk Lead (2.5mm pitch)/bulk (FBR) NA Straight lead / bulk (FBA) NB Formed lead (crimped) / bulk SA Straight lead (FBR05 type) / ammo SB Straight lead (FBR07 type) / ammo TB Straight lead (FBR07 type) / ammo UB Radial lead formed / ammo US Formed lead (crimped) / bulk VB Dual side lead formed (crimped) / ammo VS Formed lead / bulk Internal code Code 00 Internal code Standard Nominal impedance min. 85 120 Excluding 03type STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 110 13 Unitmminch Please specify the lead configuration code. Note: Lead diameter (d) shall fall within a range of 0.65mm0.05mm, FBR05, and FBR07 types however, will have a lead diameter (d) range of 0.6mm0.05mm. FBA EHS Nominal impedance min. RoHS RoHS RoHS RoHS 35.0 45.0 60.0 90.0 Parts number EHS Nominal impedance min. FBR05VA121[]-00 FBR06850NA-00 FBR06121NA-00 FBR07850[]-00 FBR07121[]-00 RoHS RoHS RoHS RoHS RoHS 120.0 85.0 120.0 85.0 120.0 Parts number FBA03450[]-00 FBA04450[]-00 FBA04600[]-00 FBA04900[]-00 Impedance measuring frequency MH Material HA VA 50 100 50 100 50 100 50 100 Rated current Amax. Material HA 7.0 7.0 7.0 7.0 VA 7.0 7.0 7.0 7.0 DC Resistance max. Rated current Mmin. 0.01 0.01 0.01 0.01 1.0 1.0 1.0 1.0 DC Resistance max. Rated current Mmin. 0.01 0.01 0.01 0.01 0.01 1.0 1.0 1.0 1.0 1.0 FBR Impedance measuring frequency MH Material HA VA 100 50 100 50 100 50 100 50 100 Rated current Amax. Material HA 7.0 7.0 7.0 7.0 VA 7.0 7.0 7.0 7.0 7.0 Please specify material codes (HA,VA) and [] lead configuration code. FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS PARTS NUMBER This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 13 111 LEADED FERRITE BEAD INDUCTORS PACKAGING Minimum Quantity Axial lead (FBA) Type Lead Configuration NA, KD, US KE, KF, VS AB, BB UB, VB NA, KD, US KE, KF, VS AB, BB VB, UB FBA03 FBA04 Standard quantity [pcs] Taped Bulk Ammo 1000 500 2000 3000 1000 500 1000 3000 Radial lead (FBR) Type Lead Configuration NA SA NA NB SB FBR05 FBR06 FBR07 Standard quantity [pcs] Taped Bulk Ammo 1000 2000 1000 1000 2000 Bulk dimensions Axial lead (FBA) NA Type FBA03450 FBA04450 FBA04600 FBA04900 D 2.50.2 0.0980.008 3.50.2 0.1380.008 3.50.2 0.1380.008 3.50.2 0.1380.008 L1 4.50.3 0.1770.012 4.50.3 0.1770.012 6.00.5/0 0.2360.020/0 9.00.5 0.3540.020 Dimensions L2 6.5 max. 0.256 max. 6.5 max. 0.256 max. 8.5 max. 0.335 max. 11.0 max. 0.433 max. d 0.650.05 0.0260.002 18 min. 0.709 min. Unitmminch US Type FBA03450 FBA04450 D 2.50.2 0.0980.008 3.50.2 0.1380.008 A 4.50.3 0.1770.012 4.50.3 0.1770.012 Dimensions a 9.0 max. 0.354 max. 9.0 max. 0.354 max. F d 5.01.0 0.1970.039 0.650.05 0.0260.002 Unitmminch This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_FBA_FBR_pack_e-01 KD/KE/KF Type Lead Symbol D 2.50.2 0.0980.008 3.50.2 0.1380.008 3.50.2 0.1380.008 2.50.2 0.0980.008 3.50.2 0.1380.008 3.50.2 0.1380.008 3.50.2 0.1380.008 2.50.2 0.0980.008 3.50.2 0.1380.008 3.50.2 0.1380.008 3.50.2 0.1380.008 FBA03450 FBA04450 KD FBA04600 FBA03450 FBA04450 KE FBA04600 FBA04900 FBA03450 FBA04450 KF FBA04600 FBA04900 F 10.01.0 0.3940.039 10.01.0 0.3940.039 10.01.0 0.3940.039 12.51.0 0.4920.039 12.51.0 0.4920.039 12.51.0 0.4920.039 12.51.0 0.4920.039 15.01.0 0.5910.039 15.01.0 0.5910.039 15.01.0 0.5910.039 15.01.0 0.5910.039 Dimensions L1 4.50.3 0.1770.012 4.50.3 0.1770.012 6.00.5/0 0.2360.020/0 4.50.3 0.1770.012 4.50.3 0.1770.012 6.00.5/0 0.2360.020/0 9.00.5 0.3540.020 4.50.3 0.1770.012 4.50.3 0.1770.012 6.00.5/0 0.2360.020/0 9.00.53 0.3540.020 d 0.650.05 0.0260.020 0.650.05 0.0260.020 0.650.05 0.0260.020 7.02.0 0.2760.079 7.52.0 0.2950.079 7.52.0 0.2950.079 7.02.0 0.2760.079 7.52.0 0.2950.079 7.52.0 0.2950.079 7.52.0 0.2950.079 7.02.0 0.2760.079 7.52.0 0.2950.079 7.52.0 0.2950.079 7.52.0 0.2950.079 Unitmminch VS 51 for 900 type only Type FBA03450 FBA04450 FBA04600 FBA04900 D 2.50.2 0.0980.008 3.50.2 0.1380.008 3.50.2 0.1380.008 3.50.2 0.1380.008 A 4.50.3 0.1770.012 4.50.3 0.1770.012 6.00.5/0 0.2360.020/0 9.00.5 0.3540.020 Dimenions a 12.5 max. 0.492 max. 12.5 max. 0.492 max. 12.5 max. 0.492 max. 16.0 max. 0.630 max. F 5.01.0 0.1970.039 5.01.0 0.1970.039 5.01.0 0.1970.039 5.01.0 0.1970.039 d 0.650.05 0.0260.002 0.650.05 0.0260.002 0.650.05 0.0260.002 0.650.05 0.0260.002 Unitmminch This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_FBA_FBR_pack_e-01 Radial lead (FBR) NA Type FBR05VA121 FBR06850 FBR06121 Dimensions D 5.0 max. 0.197 max. 6.00.5 0.2360.020 6.00.5 0.2360.020 L1 9.0 max. 0.354 max. 7.0 max. 0.276 max. 9.0 max. 0.354 max. d 0.650.05 0.0260.002 0.650.05 0.0260.002 0.650.05 0.0260.002 10.03/5 0.3940.118/0.197 10.03/5 0.3940.118/0.197 10.03/5 0.3940.118/0.197 W 2.5 max. 0.098 max. 3.00.5 0.1180.020 3.00.5 0.1180.020 F 2.51.0 0.0980.039 2.51.0 0.0980.039 2.51.0 0.0980.039 Unitmminch NB Type FBR07850 FBR07121 D 7.50.5 0.2950.020 7.50.5 0.2950.020 L1 7.0 max. 0.276 max. 9.0 max. 0.354 max. d 0.60.05 0.0240.002 0.60.05 0.0240.002 Dimensions 5.01/2 0.1970.039/0.079 5.01/2 0.1970.039/0.079 W 2.5 max. 0.098 max. 2.5 max. 0.098 max. F 5.01/0.5 0.1970.039/0.020 5.01/0.5 0.1970.039/0.020 Unitmminch Taping Dimensions ABa: 26mm1.02inch lead space Type FBA03 D 2.50.2 0.0980.008 FBA04450 FBA04600 FBA04900 3.50.2 0.1380.008 L 4.50.3 0.1770.012 4.50.3 0.1770.012 6.00.5/0 0.2360.020/0 9.00.5 0.3540.020 Dimensions a 26.01.5/0 1.020.059/0 b 0.8max 0.031max |L1-L2| 1.0 max 0.039 max d 0.650.05 0.0260.002 Minimum insertion pitch 10.0 0.394 26.01.5/0 1.020.059/0 0.8max 0.031max 1.0 max 0.039 max 0.650.05 0.0260.002 10.0 0.394 Unitmminch This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_FBA_FBR_pack_e-01 BBa: 52mm 2.05inches lead space Type FBA03 D 2.50.2 0.0980.008 FBA04450 FBA04600 3.50.2 0.1380.008 FBA04900 L 4.50.3 0.1770.012 4.50.3 0.1770.012 6.00.5/0 0.2360.020/0 9.00.5 0.3540.020 Dimensions a 52.02/1 2.050.079/0.039 b 1.2 max 0.047 max |L1-L2| 1.0 max 0.039 max d 0.650.05 0.0260.002 Minimum insertion pitch 10.0 0.394 52.02/1 2.050.079/0.039 1.2max 0.047max 1.0 max 0.039 max 0.650.05 0.0260.002 10.0 0.394 Unitmminch SAF: 2.5mm pitch0.098 inches Type Symbol Dimensions 9.0 max. A 0.354 max. 2.5 max. T 0.098 max. 5.0 max. D 0.197 max. 18.02.0/0 FBR05 H 0.7090.079/0 12.71.0 P 0.5000.039 12.70.3 1 P0 0.5000.039 5.10.7 P1 0.2010.028 1 Accumulated error for 20 pitches is 2mm. 2 Bonding tape must not protrude from the base tape. 121: Symbol P2 F h W W0 W1 W2 Dimensions 6.351.3 0.2500.051 2.51.0/0.5 0.0980.039/0.020 0.02.0 0.00.079 18.01.0/0.5 0.7090.039/0.020 12.5 min. 0.492 min. 9.00.75/0.5 0.3540.039/0.020 3.0 max. 2 0.118 max. Symbol D0 d L t Dimensions 1.0 max. 0.039 max. 4.00.3 0.1570.012 0.650.05 0.0260.002 11.0 max. 0.433 max. 0.70.2 0.0280.008 Unit mminch This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_FBA_FBR_pack_e-01 SB/TBF: 5mm pitch0.197 inches Type Symbol Dimensions 9.0 max. 0.354 max. 850: 7.0 max. 0.276 max. 2.5 max. 0.098 max. 7.50.5 0.9250.020 SB: 18.02.0/0 0.7090.079/0 TB: 16.00.5 0.6300.020 12.71.0 0.5000.039 121: A T FBR07 D H P Symbol P0 P1 P2 F h W W0 Dimensions 12.70.3 1 0.5000.012 3.850.8 0.1520.028 6.351.3 0.2500.051 5.01.0/0.5 0.1970.039/0.020 0.02.0 0.00.079 18.01.0/0.5 0.7090.039/0.020 12.5 min. 0.492 min. Symbol Dimensions 3.850.8 0.1520.032 6.351.3 0.2500.051 5.01.0 0.1970.039 0.02.0 0.00.079 18.01.0/0.5 0.7090.039/0.020 12.5 min. 0.492 min. 9.00.75/0.5 0.3540.039/0.020 Symbol W1 W2 D0 d L t Dimensions 9.00.75/0.5 0.3540.039/0.020 3.0 max. 2 0.118 max. 1.0 max. 0.039 max. 4.00.3 0.1570.012 0.650.05 0.020.002 11.0 max. 0.433 max. 0.70.2 0.0280.008 Unit mminch 1 Accumulated error for 20 pitches is 2mm. 2 Bonding tape must not protrude from the base tape. UB Type Symbol Dimensions 4.50.3 A 0.1770.012 9.0 max. A1 0.354 max. 03: 2.7 max. 0.106 max. D FBA03450 04: 3.7 max. FBA04450 0.146 max. 20.00.5/1.0 H 0.7870.020/0.039 12.71.0 P 0.5000.039 12.70.3 1 P0 0.5000.012 1 Accumulated error for 20 pitches is 2mm. 2 Bonding tape must not protrude from the base tape. Symbol P1 P2 F h W W0 W1 W2 D0 d L t Dimensions 3.0 max. 2 0.118 max. 1.0 max. 0.039 max. 4.00.3 0.1570.012 0.650.05 0.0260.002 11.0 max. 0.433 max. 0.70.2 0.0280.008 Unit mminch This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_FBA_FBR_pack_e-01 VB Type Symbol Dimensions 4.50.3 0.1770.012 600: 6.00.5/0 A 0.2360.020/0 900: 9.00.5 0.3540.020 450: 12.5 max. FBA03450 600: 0.492 max. FBA04450 A1 FBA04600 900: 16.0 max. FBA04900 0.630 max. 3.7 max. D 0.146 max. 16.00.5 H0 0.6500.020 12.71.0 P 0.5000.039 1 Accumulated error for 20 pitches is 2mm. 2 Bonding tape must not protrude from the base tape. 450: Symbol P0 P1 P2 F h W W0 W1 Dimensions 12.70.3 1 0.5000.012 3.850.8 0.1520.032 6.351.3 0.2500.051 5.01.0 0.1970.039 0.02.0 0.00.079 18.01.0/0.5 0.7090.039/0.020 12.5 min. 0.492 min. 9.00.75/0.5 0.3540.039/0.020 Symbol W2 D0 d L t Dimensions 3.0 max. 2 0.118 max. 1.0 max. 0.039 max. 4.00.3 0.1570.012 0.650.05 0.0260.002 11.0 max. 0.433 max. 0.70.2 0.0280.008 Unit mminch This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_FBA_FBR_pack_e-01 AXIAL LEADED INDUCTORSCAL Type RADIAL LEADED INDUCTORSLH Type LEADED FERRITE BEAD INDUCTORS FB Series A TypeR Type RELIABILITY DATA 1. Operating temperature Range CAL45 Type Specified Value 25 105 LHL FBA/FBR Test Methods and Remarks CA LHL 25 85 : Including self-generated heat : Including self-generated heat 2. Storage temperature Range CAL45 Type Specified Value LHL 40 85 FBA/FBR 3. Rated current CAL45 Type Specified Value LHL Within the specified tolerance FBA/FBR CA : Test Methods and Remarks The maximum DC value having inductance within 10% and temperature increase within 40 by the application of DC bias. LHL : The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10within 30%) and temperature increase within the following specified temperature by the application of DC bias. Reference temperature : 25LHL08, LHL10, LHL13 : 30LHL16, LHLP : 40LHLC08, LHLC10 FB : No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be within 20% of the initial value. This is not guaranteed for electrical characteristics during current application. 4. Impedance CAL45 Type Specified Value LHL FBA/FBR Test Methods and Remarks FB : Measuring equipment Measuring frequency Within the specified tolerance : Impedance analyzer (HP4191A) or its equivalent : Specified frequency 5. Inductance CAL45 Type Specified Value LHL Within the specified tolerance FBA/FBR Test Methods and Remarks CA : Measuring equipment Measuring frequency LHL : Measuring equipment Measuring frequency : LCR meter (HP4285A + HP42851A or its equivalent) : Specified frequency : LCR meter (HP4285AHP42851A or its equivalent) : LCR meter (HP4263A) or its equivalent (at 1kHz) : Specified frequency This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-01 6. Q CAL45 Type Specified Value LHL FBA/FBR Test Methods and Remarks LHL (except LHLP) : Measuring equipment : LCR meter (HP4285AHP42851A or its equivalent) : LCR meter (HP4263A) or its equivalent (at 1kHz) Measuring frequency : Specified frequency 7. DC Resistance CAL45 Type Specified Value LHL Within the specified tolerance FBA/FBR Test Methods and Remarks CA : Measuring equipment LHLFB : Measuring equipment : low ohmmeter (A&D AD5812 or its equivalent) : DC ohmmeter 8. Self resonance frequency CAL45 Type Specified Value LHL FBA/FBR Test Methods and Remarks LHL(except LHLP) : Measuring equipment : (HP4191A, 4192A) it equivalent 9. Temperature characteristic CAL45 Type Specified Value LHL L/L : Within 7% (except LHLP16 : Within 20%) FBA/FBR Test Methods and Remarks Change of maximum inductance deviation in step 1 to 5 Temperature () Step LHL 1 20 2 Minimum operating temperature 3 20 (Standard temperature) 4 Maximum operating temperature 5 20 10. Tensile strength test CAL45 Type Specified Value LHL FBA/FBR Test Methods and Remarks No abnormality such as cut lead, or looseness. No abnormality such as cut lead, or looseness. CA : Apply the stated tensile force progressively in the direction to draw terminal. force (N) duration (s) 10 10 LHL : Apply the stated tensile force progressively in the direction to draw terminal. Nominal wire diameter tensile d (mm) force (N) duration (s) 0.3d0.5 5 305 0.5d0.8 10 0.8d1.2 25 FBA/FBR : The body of a component shall be fixed and a tensile force of 201N shall be applied to the lead wire in the of the component during 101 seconds. axial direction This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-01 11. Over current Specified Value CAL45 Type No emission of smoke no firing. LHL There shall be no scorch or short of wire. LHLC08, LHLC10 : There shall be no firing. FBA/FBR Test Methods and Remarks LHL/CAL45 Type Measuring current : Rated currentx2 Duration : 5 min. Number of measuring : one time 12. Terminal strength : bending CAL45 Type Specified Value LHL No abnormality such as cut lead, or looseness. FBA/FBR CA : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made. Number of bends : Two times. Nominal wire diameter Mass reference Bending force tensile weight 0.3 d0.5 2.5 0.25 0.5 d0.8 5 0.50 Test Methods and Remarks LHFB : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made. Number of bends : Two times. Nominal wire diameter Mass reference Bending force tensile weight 0.3d0.5 2.5 0.25 0.5d0.8 5 0.5 0.8d1.2 10 1.0 13. Insulation resistance : between the terminals and body CAL45 Type Specified Value LHL 100M min. FBA/FBR Test Methods and Remarks LHL : Applied voltage Duration : 500 VDC : 60 sec. 14. Insulation resistance : between terminals and core CAL45 Type Specified Value LHL FBA/FBR Test Methods and Remarks FBAFBR : Applied voltage Duration 1M min. (Other than material code MA) : 100 VDC : 605 sec. 15. Withstanding : between the terminals and body CAL45 Type Specified Value LHL No abnormality such as insulation damage FBA/FBR Test Methods and Remarks LHL : According to JIS C5102. 7. 1. 3 (C) Metal global method Applied voltage : 500 VDC Duration : 60 sec. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-01 16. DC bias characteristic CAL45 Type Specified Value L/L : Within 10% LHL FBA/FBR Test Methods and Remarks CA : Measure inductance with application of rated current using LCR meter to compare it with the initial value. 17. Body strength CAL45 Type Specified Value No abnormality as damage. LHL FBA/FBR Test Methods and Remarks CAL45 : Applied force Duration Speed FBA : Applied force Duration No abnormality such as cracks on body. :50N : 10 sec. : Shall attain to specified force in 2 sec. : 503N : 301 sec. 18. Resistance to vibration Specified Value Test Methods and Remarks CAL45 Type L/L : Within 5% LHL Appearance : No abnormality L/L : Within 5% Q change : Within 30% (LHLP : only L/L) FBA/FBR Appearance : No abnormality Impedance change : Within 20% CA : Directions Frequency range Amplitude Mounting method Recovery LHLFB : Directions Frequency range Amplitude Mounting method : 2 hrseach in X, Y and Z directions total : 6hrs. : 10 to 55 to 10Hz (1min.) : 1.5mm : Soldering onto printed board. : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs. : 2 hrs each in X, Y and Z directions total : 6hrs. : 10 to 55 to 10Hz (1min.) : 1.5mm (But don't exceed acceleration 196m/s2 (two power)) : Soldering onto printed board. 19. Resistance to shock CAL45 Type Specified Value No significant abnormality in appearance LHL FBA/FBR Test Methods and Remarks CA : Drop test Impact material Height Total number of drops : concrete or vinyl tile : 1m : 10 times This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-01 20. Solderability Specified Value Test Methods and Remarks CAL45 Type At least 75 of terminal electrode is covered by new solder. LHL At least 75 of terminal electrode is covered by new solder. FBA/FBR At least 90 of terminal electrode is covered by new solder. CA : Solder temperature Duration LHL : Solder temperature Duration Immersion depth FB : Solder temperature Duration Immersion depth : 2305 : 20.5 sec. : 2355 : 20.5 sec. : Up to 1.5mm from bottom of case. : 2305 : 31 sec. : Up to 1.5mm from terminal root. 21. Resistance to soldering heat Specified Value CAL45 Type L/L : Within 5% LHL No significant abnormality in appearance Inductance change : Within 5% Q change : Within 30%(LHLP : only L/L) FBA/FBR No significant abnormality in appearance Impedance change : Within 20% CA : Solder temperature Duration Immersed conditions Recovery : : : : LHL : Solder bath method : 2705 50.5 sec. One time Inserted into substrate with t=1.6mm At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs. Solder temperature Duration Manual soldering : Caution Recovery : : : : : : : : 2605 101 sec. Up to 1.5mm from the bottom of case. 35010 (At the tip of soldering iron) 51 sec. Up to 1.5mm from the bottom of case. No excessive pressing shall be applied to terminals. 4 to 24hrs of recovery under the standard condition after the test. Solder temperature Duration Immersion depth Solder temperature Duration Immersion depth Recovery : : : : : : : 2605 101 sec. Up to 1.5mm from the terminal root. 3505 31 sec. Up to 1.5mm from the terminal root. 3hrs of recovery under the standard condition after the test. Solder temperature Duration Test Methods and Remarks FB : Solder bath method: Condition 1: Condition 2 : 22. Resistance to solvent CAL45 Type Specified Value Please avoid the ultrasonic cleaning of this product. LHL No significant abnormality in appearance Impedance change : Within 20% FBA/FBR Test Methods and Remarks FB : Solvent temperature Duration Solvent type Recovery : : : : 2025 305 sec. Acetone 3hrs of recovery under the standard condition after the test. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-01 23. Thermal shock Specified Value CAL45 Type L/L : Within 10% LHL Appearance : No abnormality Inductance change : Within 10% Q change : Within 30% (LHLPonly L/L) FBA/FBR Appearance : No abnormality Impedance change : Within 20% CAConditions for 1cycle Step Temperature () 1 250/3 2 Room temperature 3 852/0 4 Room temperature Number of cycles Recovery Test Methods and Remarks Duration (min.) 303 Within 3 303 Within 3 : 5 cycles : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs. LHLFB According to JIS C0025 Conditions for 1 cycle Step Temperature () 1 Minimum operating temperature0/3 2 Room temperature 3 Minimum operating temperature2/0 4 Room temperature Number of cycles Recovery : : : : Duration (min.) 303 Within 3 303 Within 3 10 cycles LHL 5 cycles (FBA, FBR) 4 to 24hrs of recovery under the standard condition after the removal from the test chamber. LHL 3hrs of recovery under the standard condition after the removal from the test chamber. (FBA, FBR) 24. Damp heat CAL45 Type Specified Value L/L : Within 10% LHL AppearanceNo abnormality Impedance changeWithin 20% FBA/FBR Test Methods and Remarks CA : Temperature Humidity Duration Recovery FB : Temperature Humidity Duration Recovery : 402 : 9095%RH : 1000 hrs : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. : : : : 602 9095%RH 1000 hrs 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-01 25. Loading under damp heat Specified Value CAL45 Type L/L : Within 10% LHL Appearance : No abnormality Inductance change : Within 10% Q change : Within 30% (LHLP : only L/L) FBA/FBR Test Methods and Remarks CA : Temperature Humidity Duration Applied current Recovery LHL : Temperature Humidity Duration Applied current Recovery : 402 : 9095%RH : 1000 hrs : Rated current : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. : : : : : 402 9095%RH 100024 hrs Rated current 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 26. Loading at high temperature CAL45 Type Specified Value L/L : Within 10% LHL FBA/FBR Test Methods and Remarks CA : Temperature Duration Applied current Recovery : 852 : 1000 hrs : Rated current : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. 27. Low temperature life test Specified Value CAL45 Type L/L : Within 10% LHL Appearance : No abnormality Inductance change : Within 10% Q change : Within 30% (LHLP : only L/L) FBA/FBR Test Methods and Remarks CA : Temperature Duration Recovery LHL : Temperature Duration Recovery : 252 : 1000 hrs : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. :403 : 100024 hrs : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 28. High temperature life test CAL45 Type Specified Value LHL Appearance : No abnormality Inductance change : Within 10% Q change : Within 30% (LHLP : only L/L) FBA/FBR Test Methods and Remarks LHL : Temperature Duration Recovery : 1053 : 100024 hrs : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-01 AXIAL LEADED INDUCTORSCAL Type RADIAL LEADED INDUCTORSLH Type LEADED FERRITE BEAD INDUCTORS FB Series A TypeR Type PRECAUTIONS 1. Circuit Design Precautions Operating environment 1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design Precautions Technical considerations Design 1. Please design insertion pitches as matching to that of leads of the component on PCBs. Design 1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs. 3. Considerations for automatic placement Precautions Technical considerations Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. Adjustment of mounting machine 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 4. Soldering Precautions Wave soldering 1. Please refer to the specifications in the catalog for a wave soldering. 2. Do not immerse the entire inductor in the flux during the soldering operation. Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc sufficiently. Recommended conditions for using a soldering iron: Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350 Duration - 3 seconds or less The soldering iron should not directly touch the inductor. Reflow soldering 1. As for reflow soldering, please contact our sales staff. Technical considerations Lead free soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. Recommended conditions for using a soldering iron If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. 5. Cleaning Precautions Technical considerations Cleaning conditions 1. CAL type, LH type Please do not do cleaning by a supersonic wave. Cleaning conditions 1. CAL type, LH type, If washing by supersonic waves, supersonic waves may deform products. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_prec_e-01 6. Handling Precautions Technical considerations Handling 1. Keep the inductors away from all magnets and magnetic objects. Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. 2. LH type If inductors are dropped onto the floor or a hard surface they should not be used. Packing 1. Please do not give the inductors any excessive mechanical shocks. In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item). Handling 1. There is a case that a characteristic varies with magnetic influence. Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 2. LH type There is a case to be broken by a fall. Packing 1. There is a case that a lead wire could be deformed by a fall or an excessive shock. 7. Storage conditions Precautions Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Recommended conditions Ambient temperature 040 Humidity Below 70% RH The ambient temperature must be kept below 30. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, inductors should be used within one year from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. Technical considerations Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_prec_e-01