1
3
Notice for TAIYO YUDEN products
Please read this notice before using the TAIYO YUDEN products.
REMINDERS
■ Product information in this catalog is as of October 2012. All of the contents specified herein are subject to change
without notice due to technical improvements, etc. Therefore, please check for the latest information carefully be-
fore practical application or usage of the Products.
Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorpo-
rating such products, which are caused under the conditions other than those specified in this catalog or individual
specification.
■ Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is
available.
■ Please conduct validation and verification of products in actual condition of mounting and operating environment
before commercial shipment of the equipment.
■ All electronic components or functional modules listed in this catalog are developed, designed and intended for
use in general electronics equipment.(for AV, office automation, household, office supply, information service,
telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any
equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal,
disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have
direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, subma-
rine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic equipment,
if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliabil-
ity evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to
install a protective circuit is strongly recommended at customer's design stage.
■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distribu-
tors (so called TAIYO YUDENs official sales channel).
It is only applicable to the products purchased from any of TAIYO YUDEN s official sales channel.
■ Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may oc-
cur in connection with a third party's intellectual property rights and other related rights arising from your usage of
products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights.
■ Caution for export
Certain items in this catalog may require specific procedures for export according to Foreign Exchange and For-
eign Trade Control Law of Japan, U.S. Export Administration Regulations, and other applicable regulations.
Should you have any question or inquiry on this matter, please contact our sales staff.
1
3
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
110
NOISE SUPPRESSION COMPONENTS
／
FERRITE BEAD INDUCTORS
LEADED FERRITE BEAD INDUCTORS (FB SERIES A TYPE / R TYPE)
■PARTS NUMBER
F B A 0 4 H A 4 5 0 B B － 0 0 △＝Blank space
① ② ③ ④ ⑤ ⑥ ⑦
①Series name
Code Series name
FB Ferrite bead
②Shape
Code Shape
A Axial lead
R Radial lead
③Dimensions of core（D）
Code Dimensions of core（D）［mm］
03 φ2.5
04 φ3.5
05 5.0
06 6.0
07 7.5
④Material
Code Material
HA Refer to impedance curves
for material differences
VA
⑤Nominal impedance
Code
（example） Nominal impedance［Ω min.］
850 85
121 120
Excluding 03type
⑥Lead configuration
Code Lead configurations［ｍｍ］
AB Straight lead (26mm lead space) / ammo
BB Straight lead (52mm lead space) / ammo
KD Formed lead (10mm pitch) / bulk
KE Formed lead (12.5mm pitch) / bulk
KF Formed lead / bulk (15.0mm pitch) / bulk
NA Lead (2.5mm pitch)/bulk (FBR)
Straight lead / bulk (FBA)
NB Formed lead (crimped) / bulk
SA Straight lead (FBR05 type) / ammo
SB Straight lead (FBR07 type) / ammo
TB Straight lead (FBR07 type) / ammo
UB Radial lead formed / ammo
US Formed lead (crimped) / bulk
VB Dual side lead formed (crimped) / ammo
VS Formed lead / bulk
⑦Internal code
Code Internal code
－00 Standard
■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY
LEADED FERRITE BEAD INDUCTORS(FB SERIES A TYPE / R TYPE)
WAV E
1
3
▶Thiscatalogcontainsthetypicalspecicationonlyduetothelimitationofspace.Whenyouconsiderthepurchaseofourproducts,pleasecheckourspecication.
Fordetailsofeachproduct(characteristicsgraph,reliabilityinformation,precautionsforuse,andsoon),seeourWebsite(http://www.ty-top.com/).
111
NOISE SUPPRESSION COMPONENTS
／
FERRITE BEAD INDUCTORS
Unit：mm（inch）
□Please specify the lead configuration code.
Note: Lead diameter (φd) shall fall within a range of 0.65mm±0.05mm, FBR05, and FBR07 types however, will have a lead diameter (φd) range of
0.6mm±0.05mm.
■PARTS NUMBER
●FBA
HAVAHA VA
FBA03△450[]-00 RoHS 35.050 100 7.07.00.011.0
FBA04△450[]-00 RoHS 45.050 100 7.07.00.011.0
FBA04△600[]-00 RoHS 60.050 100 7.07.00.011.0
FBA04△900[]-00 RoHS 90.050 100 7.07.00.011.0
●FBR
HAVAHA VA
FBR05VA121[]-00 RoHS 120.0 - 100 - 7.00.011.0
FBR06△850NA-00RoHS85.050 100 7.07.00.011.0
FBR06△121NA-00 RoHS 120.050 100 7.07.00.011.0
FBR07△850[]-00 RoHS 85.050 100 7.07.00.011.0
FBR07△121[]-00 RoHS 120.050 100 7.07.00.011.0
※△Please specify material codes (HA,VA) and [] lead configuration code.
Impedance measuring frequency
［MHｚ］
Impedance measuring frequency
［MHｚ］
Rated current
［A］（max.）
lairetaMlairetaM
DC Resistance
［Ω］（max.）
DC Resistance
［Ω］（max.）
Material
Nominal impedance
［Ω］（min.）
Rated current
［MΩ］（min.）
Rated current
［MΩ］（min.）
Rated current
［A］（max.）
Material
Parts numberEHS
Parts numberEHS Nominal impedance
［Ω］（min.）
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_FBA_FBR_pack_e-01
LEADED FERRITE BEAD INDUCTORS
■PACKAGING
①Minimum Quantity
●Axial lead (FBA)
Type Lead Configuration
Standard quantity [pcs]
Bulk Taped
Ammo
FBA03
NA, KD, US 1000 －
KE, KF, VS 500 －
AB, BB － 2000
UB, VB － 3000
FBA04
NA, KD, US 1000 －
KE, KF, VS 500 －
AB, BB － 1000
VB, UB － 3000
●Radial lead (FBR)
Type Lead Configuration
Standard quantity [pcs]
Bulk Taped
Ammo
FBR05 NA 1000 －
SA － 2000
FBR06 NA 1000 －
FBR07 NB 1000 －
SB － 2000
②Bulk dimensions
Axial lead (FBA)
●NA
Type Dimensions
φD L1 L2 φd ℓ
FBA03□450 2.5±0.2
（0.098±0.008）
4.5±0.3
（0.177±0.012）
6.5 max.
（0.256 max.）
0.65±0.05
（0.026±0.002）
18 min.
（0.709 min.）
FBA04□450 3.5±0.2
（0.138±0.008）
4.5±0.3
（0.177±0.012）
6.5 max.
（0.256 max.）
FBA04□600 3.5±0.2
（0.138±0.008）
6.0＋0.5/－0
（0.236＋0.020/－0）
8.5 max.
（0.335 max.）
FBA04□900 3.5±0.2
（0.138±0.008）
9.0±0.5
（0.354±0.020）
11.0 max.
（0.433 max.）
Unit：mm（inch）
●US
Type Dimensions
φD A a F φd
FBA03□450 2.5±0.2
（0.098±0.008）
4.5±0.3
（0.177±0.012）
9.0 max.
（0.354 max.） 5.0±1.0
（0.197±0.039）
0.65±0.05
（0.026±0.002）
FBA04□450 3.5±0.2
（0.138±0.008）
4.5±0.3
（0.177±0.012）
9.0 max.
（0.354 max.）
Unit：mm（inch）
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_FBA_FBR_pack_e-01
●KD/KE/KF
Type Lead Symbol Dimensions
φD F L1 φd ℓ
FBA03□450
KD
2.5±0.2
（0.098±0.008）
10.0±1.0
（0.394±0.039）
4.5±0.3
（0.177±0.012）
0.65±0.05
（0.026±0.020）
7.0±2.0
（0.276±0.079）
FBA04□450 3.5±0.2
（0.138±0.008）
10.0±1.0
（0.394±0.039）
4.5±0.3
（0.177±0.012）
7.5±2.0
（0.295±0.079）
FBA04□600 3.5±0.2
（0.138±0.008）
10.0±1.0
（0.394±0.039）
6.0＋0.5/－0
（0.236＋0.020/－0）
7.5±2.0
（0.295±0.079）
FBA03□450
KE
2.5±0.2
（0.098±0.008）
12.5±1.0
（0.492±0.039）
4.5±0.3
（0.177±0.012）
0.65±0.05
（0.026±0.020）
7.0±2.0
（0.276±0.079）
FBA04□450 3.5±0.2
（0.138±0.008）
12.5±1.0
（0.492±0.039）
4.5±0.3
（0.177±0.012）
7.5±2.0
（0.295±0.079）
FBA04□600 3.5±0.2
（0.138±0.008）
12.5±1.0
（0.492±0.039）
6.0＋0.5/－0
（0.236＋0.020/－0）
7.5±2.0
（0.295±0.079）
FBA04□900 3.5±0.2
（0.138±0.008）
12.5±1.0
（0.492±0.039）
9.0±0.5
（0.354±0.020）
7.5±2.0
（0.295±0.079）
FBA03□450
KF
2.5±0.2
（0.098±0.008）
15.0±1.0
（0.591±0.039）
4.5±0.3
（0.177±0.012）
0.65±0.05
（0.026±0.020）
7.0±2.0
（0.276±0.079）
FBA04□450 3.5±0.2
（0.138±0.008）
15.0±1.0
（0.591±0.039）
4.5±0.3
（0.177±0.012）
7.5±2.0
（0.295±0.079）
FBA04□600 3.5±0.2
（0.138±0.008）
15.0±1.0
（0.591±0.039）
6.0＋0.5/－0
（0.236＋0.020/－0）
7.5±2.0
（0.295±0.079）
FBA04□900 3.5±0.2
（0.138±0.008）
15.0±1.0
（0.591±0.039）
9.0±0.53
（0.354±0.020）
7.5±2.0
（0.295±0.079）
Unit：mm（inch）
●VS
※5±1 for 900 type only
Type Dimenions
φD A a F φd
FBA03□450 2.5±0.2
（0.098±0.008）
4.5±0.3
（0.177±0.012）
12.5 max.
（0.492 max.）
5.0±1.0
（0.197±0.039）
0.65±0.05
（0.026±0.002）
FBA04□450 3.5±0.2
（0.138±0.008）
4.5±0.3
（0.177±0.012）
12.5 max.
（0.492 max.）
5.0±1.0
（0.197±0.039）
0.65±0.05
（0.026±0.002）
FBA04□600 3.5±0.2
（0.138±0.008）
6.0＋0.5/－0
（0.236＋0.020/－0）
12.5 max.
（0.492 max.）
5.0±1.0
（0.197±0.039）
0.65±0.05
（0.026±0.002）
FBA04□900 3.5±0.2
（0.138±0.008）
9.0±0.5
（0.354±0.020）
16.0 max.
（0.630 max.）
5.0±1.0
（0.197±0.039）
0.65±0.05
（0.026±0.002）
Unit：mm（inch）
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_FBA_FBR_pack_e-01
Radial lead (FBR)
●NA
Type Dimensions
D L1 φd ℓ W F
FBR05VA121 5.0 max.
（0.197 max.）
9.0 max.
（0.354 max.）
0.65±0.05
（0.026±0.002）
10.0＋3/－5
（0.394＋0.118/－0.197）
2.5 max.
（0.098 max.）
2.5±1.0
（0.098±0.039）
FBR06□850 6.0±0.5
（0.236±0.020）
7.0 max.
（0.276 max.）
0.65±0.05
（0.026±0.002）
10.0＋3/－5
（0.394＋0.118/－0.197）
3.0±0.5
（0.118±0.020）
2.5±1.0
（0.098±0.039）
FBR06□121 6.0±0.5
（0.236±0.020）
9.0 max.
（0.354 max.）
0.65±0.05
（0.026±0.002）
10.0＋3/－5
（0.394＋0.118/－0.197）
3.0±0.5
（0.118±0.020）
2.5±1.0
（0.098±0.039）
Unit：mm（inch）
●NB
Type Dimensions
D L1 φd ℓ W F
FBR07□850 7.5±0.5
（0.295±0.020）
7.0 max.
（0.276 max.）
0.6±0.05
（0.024±0.002）
5.0＋1/－2
（0.197＋0.039/－0.079）
2.5 max.
（0.098 max.）
5.0＋1/－0.5
（0.197＋0.039/－0.020）
FBR07□121 7.5±0.5
（0.295±0.020）
9.0 max.
（0.354 max.）
0.6±0.05
（0.024±0.002）
5.0＋1/－2
（0.197＋0.039/－0.079）
2.5 max.
（0.098 max.）
5.0＋1/－0.5
（0.197＋0.039/－0.020）
Unit：mm（inch）
③Taping Dimensions
●AB（a: 26mm）（1.02inch lead space）
Type Dimensions Minimum insertion
pitch
φD L a b |L1-L2| φd
FBA03 2.5±0.2
（0.098±0.008）
4.5±0.3
（0.177±0.012）
26.0＋1.5/－0
（1.02＋0.059/－0）
0.8max
（0.031max）
1.0 max
（0.039 max）
0.65±0.05
（0.026±0.002）
10.0
（0.394）
FBA04□450
3.5±0.2
（0.138±0.008）
4.5±0.3
（0.177±0.012）
26.0＋1.5/－0
（1.02＋0.059/－0）
0.8max
（0.031max）
1.0 max
（0.039 max）
0.65±0.05
（0.026±0.002）
10.0
（0.394）
FBA04□600 6.0＋0.5/－0
（0.236＋0.020/－0）
FBA04□900 9.0±0.5
（0.354±0.020）
Unit：mm（inch）
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_FBA_FBR_pack_e-01
●BB（a: 52mm）（ 2.05inches lead space）
Type Dimensions Minimum insertion
pitch
φD L a b |L1-L2| φd
FBA03 2.5±0.2
（0.098±0.008）
4.5±0.3
（0.177±0.012）
52.0＋2/－1
（2.05＋0.079/－0.039）
1.2 max
（0.047 max）
1.0 max
（0.039 max）
0.65±0.05
（0.026±0.002）
10.0
（0.394）
FBA04□450
3.5±0.2
（0.138±0.008）
4.5±0.3
（0.177±0.012）
52.0＋2/－1
（2.05＋0.079/－0.039）
1.2max
（0.047max）
1.0 max
（0.039 max）
0.65±0.05
（0.026±0.002）
10.0
（0.394）
FBA04□600 6.0＋0.5/－0
（0.236＋0.020/－0）
FBA04□900 9.0±0.5
（0.354±0.020）
Unit：mm（inch）
●SA（F: 2.5mm pitch）（0.098 inches）
Type Symbol Dimensions Symbol Dimensions Symbol Dimensions
FBR05
A 121: 9.0 max.
（0.354 max.） P2 6.35±1.3
（0.250±0.051） ℓ 1.0 max.
（0.039 max.）
T 2.5 max.
（0.098 max.） F 2.5＋1.0/－0.5
（0.098＋0.039/－0.020） φD0 4.0±0.3
（0.157±0.012）
D 5.0 max.
（0.197 max.） △h 0.0±2.0
（0.0±0.079） φd 0.65±0.05
（0.026±0.002）
H 18.0＋2.0/－0
（0.709＋0.079/－0） W 18.0＋1.0/－0.5
（0.709＋0.039/－0.020） L 11.0 max.
（0.433 max.）
P 12.7±1.0
（0.500±0.039） W0 12.5 min.
（0.492 min.） t 0.7±0.2
（0.028±0.008）
P0 12.7±0.3 ※1
（0.500±0.039） W1 9.0＋0.75/－0.5
（0.354＋0.039/－0.020） Unit： mm（inch）
P1 5.1±0.7
（0.201±0.028） W2 3.0 max. ※2
（0.118 max.）
※1 Accumulated error for 20 pitches is ±2mm.
※2 Bonding tape must not protrude from the base tape.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_FBA_FBR_pack_e-01
●SB/TB（F: 5mm pitch）（0.197 inches）
Type Symbol Dimensions Symbol Dimensions Symbol Dimensions
FBR07
A
121: 9.0 max.
（0.354 max.） P0 12.7±0.3 ※1
（0.500±0.012） W1 9.0＋0.75/－0.5
（0.354＋0.039/－0.020）
850: 7.0 max.
（0.276 max.） P1 3.85±0.8
（0.152±0.028） W2 3.0 max. ※2
（0.118 max.）
T 2.5 max.
（0.098 max.） P2 6.35±1.3
（0.250±0.051） ℓ 1.0 max.
（0.039 max.）
D 7.5±0.5
（0.925±0.020） F 5.0＋1.0/－0.5
（0.197＋0.039/－0.020） φD0 4.0±0.3
（0.157±0.012）
H
SB: 18.0＋2.0/－0
（0.709＋0.079/－0） △h 0.0±2.0
（0.0±0.079） φd 0.65±0.05
（0.02±0.002）
TB: 16.0±0.5
（0.630±0.020） W 18.0＋1.0/－0.5
（0.709＋0.039/－0.020） L 11.0 max.
（0.433 max.）
P 12.7±1.0
（0.500±0.039） W0 12.5 min.
（0.492 min.） t 0.7±0.2
（0.028±0.008）
Unit： mm（inch）
※1 Accumulated error for 20 pitches is ±2mm.
※2 Bonding tape must not protrude from the base tape.
●UB
Type Symbol Dimensions Symbol Dimensions Symbol Dimensions
FBA03□450
FBA04□450
A 4.5±0.3
（0.177±0.012） P1 3.85±0.8
（0.152±0.032） W2 3.0 max. ※2
（0.118 max.）
A1 9.0 max.
（0.354 max.） P2 6.35±1.3
（0.250±0.051） ℓ 1.0 max.
（0.039 max.）
φD
03: 2.7 max.
（0.106 max. ） F 5.0±1.0
（0.197±0.039） φD0 4.0±0.3
（0.157±0.012）
04: 3.7 max.
（0.146 max.） △h 0.0±2.0
（0.0±0.079） φd 0.65±0.05
（0.026±0.002）
H 20.0＋0.5/－1.0
（0.787＋0.020/－0.039） W 18.0＋1.0/－0.5
（0.709＋0.039/－0.020） L 11.0 max.
（0.433 max.）
P 12.7±1.0
（0.500±0.039） W0 12.5 min.
（0.492 min.） t 0.7±0.2
（0.028±0.008）
P0 12.7±0.3 ※1
（0.500±0.012） W1 9.0＋0.75/－0.5
（0.354＋0.039/－0.020） Unit： mm（inch）
※1 Accumulated error for 20 pitches is ±2mm.
※2 Bonding tape must not protrude from the base tape.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_FBA_FBR_pack_e-01
●VB 形状
Type Symbol Dimensions Symbol Dimensions Symbol Dimensions
FBA03□450
FBA04□450
FBA04□600
FBA04□900
A
450: 4.5±0.3
（0.177±0.012） P0 12.7±0.3 ※1
（0.500±0.012） W2 3.0 max. ※2
（0.118 max.）
600: 6.0＋0.5/－0
（0.236＋0.020/－0） P1 3.85±0.8
（0.152±0.032） ℓ 1.0 max.
（0.039 max.）
900: 9.0±0.5
（0.354±0.020） P2 6.35±1.3
（0.250±0.051） φD0 4.0±0.3
（0.157±0.012）
A1
450: 12.5 max.
600: （0.492 max.） F 5.0±1.0
（0.197±0.039） φd 0.65±0.05
（0.026±0.002）
900: 16.0 max.
（0.630 max.） △h 0.0±2.0
（0.0±0.079） L 11.0 max.
（0.433 max.）
φD 3.7 max.
（0.146 max.） W 18.0＋1.0/－0.5
（0.709＋0.039/－0.020） t 0.7±0.2
（0.028±0.008）
H0 16.0±0.5
（0.650±0.020） W0 12.5 min.
（0.492 min. ） Unit： mm（inch）
P 12.7±1.0
（0.500±0.039） W1 9.0＋0.75/－0.5
（0.354＋0.039/－0.020）
※1 Accumulated error for 20 pitches is ±2mm.
※2 Bonding tape must not protrude from the base tape.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-01
AXIAL LEADED INDUCTORS（CAL Type）、
RADIAL LEADED INDUCTORS（LH Type）、
LEADED FERRITE BEAD INDUCTORS（ FB Series A Type／R Type）
■RELIABILITY DATA
1. Operating temperature Range
Specified Value
CAL45 Type －25～＋ 105℃
LHL□□□
FBA/FBR －25～＋ 85℃
Test Methods and
Remarks
CA : Including self-generated heat
LHL□□□ : Including self-generated heat
2. Storage temperature Range
Specified Value
CAL45 Type
－40～＋ 85℃ LHL□□□
FBA/FBR
3. Rated current
Specified Value
CAL45 Type
Within the specified tolerance LHL□□□
FBA/FBR
Test Methods and
Remarks
CA :
The maximum DC value having inductance within 10% and temperature increase within 40℃ by the application of DC bias.
LHL□□□ :
The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10：within 30%) and temperature increase within the
following specified temperature by the application of DC bias.
Reference temperature : 25℃（LHL08, LHL10, LHL13）
: 30℃（LHL16, LHLP□□）
: 40℃（LHLC08, LHLC10）
FB : No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be within
±20% of the initial value.
This is not guaranteed for electrical characteristics during current application.
4. Impedance
Specified Value
CAL45 Type
LHL□□□
FBA/FBR Within the specified tolerance
Test Methods and
Remarks
FB :
Measuring equipment : Impedance analyzer (HP4191A) or its equivalent
Measuring frequency : Specified frequency
5. Inductance
Specified Value
CAL45 Type Within the specified tolerance
LHL□□□
FBA/FBR
Test Methods and
Remarks
CA :
Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent)
Measuring frequency : Specified frequency
LHL□□□ :
Measuring equipment : LCR meter (HP4285A＋HP42851A or its equivalent)
: LCR meter (HP4263A) or its equivalent (at 1kHz)
Measuring frequency : Specified frequency
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-01
6. Q
Specified Value
CAL45 Type
LHL□□□
FBA/FBR
Test Methods and
Remarks
LHL□□□ (except LHLP) :
Measuring equipment : LCR meter (HP4285A＋HP42851A or its equivalent)
: LCR meter (HP4263A) or its equivalent (at 1kHz)
Measuring frequency : Specified frequency
7. DC Resistance
Specified Value
CAL45 Type
Within the specified tolerance LHL□□□
FBA/FBR
Test Methods and
Remarks
CA :
Measuring equipment : low ohmmeter (A&D AD5812 or its equivalent)
LHL□□□・FB :
Measuring equipment : DC ohmmeter
8. Self resonance frequency
Specified Value
CAL45 Type
LHL□□□
FBA/FBR
Test Methods and
Remarks
LHL□□□(except LHLP) :
Measuring equipment : (HP4191A, 4192A) it equivalent
9. Temperature characteristic
Specified Value
CAL45 Type
LHL□□□ △L/L : Within ±7% (except LHLP16 : Within ±20%)
FBA/FBR
Test Methods and
Remarks
Change of maximum inductance deviation in step 1 to 5
Step Temperature (℃)
LHL□□□
1 20
2 Minimum operating temperature
3 20 (Standard temperature)
4 Maximum operating temperature
5 20
10. Tensile strength test
Specified Value
CAL45 Type No abnormality such as cut lead, or looseness.
LHL□□□
FBA/FBR No abnormality such as cut lead, or looseness.
Test Methods and
Remarks
CA : Apply the stated tensile force progressively in the direction to draw terminal.
force (N) duration (s)
10 10
LHL□□□ : Apply the stated tensile force progressively in the direction to draw terminal.
Nominal wire diameter tensile φd (mm) force (N) duration (s)
0.3＜φd≦0.5 5
30±5
0.5＜φd≦0.8 10
0.8＜φd≦1.2 25
FBA/FBR : The body of a component shall be fixed and a tensile force of 20±1N shall be applied to the lead wire in the axial direction
of the component during 10±1 seconds.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-01
11. Over current
Specified Value
CAL45 Type No emission of smoke no firing.
LHL□□□ There shall be no scorch or short of wire.
LHLC08, LHLC10 : There shall be no firing.
FBA/FBR
Test Methods and
Remarks
LHL□□□/CAL45 Type ：
Measuring current : Rated current×2
Duration : 5 min.
Number of measuring : one time
12. Terminal strength : bending
Specified Value
CAL45 Type
No abnormality such as cut lead, or looseness. LHL□□□
FBA/FBR
Test Methods and
Remarks
CA :
Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the
initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter
tensile Bending force Mass reference
weight
0.3＜ φ d≦0.5 2.5 0.25
0.5＜ φ d≦0.8 5 0.50
LH・FB :
Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the
initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made.
Number of bends : Two times.
Nominal wire diameter
tensile Bending force Mass reference
weight
0.3＜φd≦0.5 2.5 0.25
0.5＜φd≦0.8 5 0.5
0.8＜φd≦1.2 10 1.0
13. Insulation resistance : between the terminals and body
Specified Value
CAL45 Type
LHL□□□ 100MΩ min.
FBA/FBR
Test Methods and
Remarks
LHL□□□ :
Applied voltage : 500 VDC
Duration : 60 sec.
14. Insulation resistance : between terminals and core
Specified Value
CAL45 Type
LHL□□□
FBA/FBR 1MΩ min. (Other than material code MA)
Test Methods and
Remarks
FBA・FBR :
Applied voltage : 100 VDC
Duration : 60±5 sec.
15. Withstanding : between the terminals and body
Specified Value
CAL45 Type
LHL□□□ No abnormality such as insulation damage
FBA/FBR
Test Methods and
Remarks
LHL□□□ :
According to JIS C5102. 7. 1. 3 (C)
Metal global method
Applied voltage : 500 VDC
Duration : 60 sec.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-01
16. DC bias characteristic
Specified Value
CAL45 Type △L/L : Within －10%
LHL□□□
FBA/FBR
Test Methods and
Remarks CA : Measure inductance with application of rated current using LCR meter to compare it with the initial value.
17. Body strength
Specified Value
CAL45 Type No abnormality as damage.
LHL□□□
FBA/FBR No abnormality such as cracks on body.
Test Methods and
Remarks
CAL45 :
Applied force :50N
Duration : 10 sec.
Speed : Shall attain to specified force in 2 sec.
FBA :
Applied force : 50±3N
Duration : 30±1 sec.
18. Resistance to vibration
Specified Value
CAL45 Type △L/L : Within ±5%
LHL□□□
Appearance : No abnormality
△L/L : Within ±5%
Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR Appearance : No abnormality
Impedance change : Within ±20%
Test Methods and
Remarks
CA :
Directions : 2 hrseach in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude : 1.5mm
Mounting method : Soldering onto printed board.
Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs.
LHL□□□・FB :
Directions : 2 hrs each in X, Y and Z directions total : 6hrs.
Frequency range : 10 to 55 to 10Hz (1min.)
Amplitude : 1.5mm (But don't exceed acceleration 196m/s2 (two power))
Mounting method : Soldering onto printed board.
19. Resistance to shock
Specified Value
CAL45 Type No significant abnormality in appearance
LHL□□□
FBA/FBR
Test Methods and
Remarks
CA :
Drop test
Impact material : concrete or vinyl tile
Height : 1m
Total number of drops : 10 times
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-01
20. Solderability
Specified Value
CAL45 Type At least 75％ of terminal electrode is covered by new solder.
LHL□□□ At least 75％ of terminal electrode is covered by new solder.
FBA/FBR At least 90％ of terminal electrode is covered by new solder.
Test Methods and
Remarks
CA :
Solder temperature : 230±5℃
Duration : 2±0.5 sec.
LHL□□□ :
Solder temperature : 235±5℃
Duration : 2±0.5 sec.
Immersion depth : Up to 1.5mm from bottom of case.
FB :
Solder temperature : 230±5℃
Duration : 3±1 sec.
Immersion depth : Up to 1.5mm from terminal root.
21. Resistance to soldering heat
Specified Value
CAL45 Type △L/L : Within ±5%
LHL□□□
No significant abnormality in appearance
Inductance change : Within ±5%
Q change : Within ±30%(LHLP : only △L/L)
FBA/FBR No significant abnormality in appearance
Impedance change : Within ±20%
Test Methods and
Remarks
CA :
Solder temperature : 270±5℃
Duration : 5±0.5 sec. One time
Immersed conditions : Inserted into substrate with t=1.6mm
Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within
2hrs.
LHL□□□ :
Solder bath method : Solder temperature : 260±5℃
Duration : 10±1 sec.
: Up to 1.5mm from the bottom of case.
Manual soldering : Solder temperature : 350±10℃ (At the tip of soldering iron)
Duration : 5±1 sec.
: Up to 1.5mm from the bottom of case.
Caution : No excessive pressing shall be applied to terminals.
Recovery : 4 to 24hrs of recovery under the standard condition after the test.
FB :
Solder bath method:
Condition 1: Solder temperature : 260±5℃
Duration : 10±1 sec.
Immersion depth : Up to 1.5mm from the terminal root.
Condition 2 : Solder temperature : 350±5℃
Duration : 3±1 sec.
Immersion depth : Up to 1.5mm from the terminal root.
Recovery : 3hrs of recovery under the standard condition after the test.
22. Resistance to solvent
Specified Value
CAL45 Type Please avoid the ultrasonic cleaning of this product.
LHL□□□
FBA/FBR No significant abnormality in appearance
Impedance change : Within ±20%
Test Methods and
Remarks
FB :
Solvent temperature : 20～25℃
Duration : 30±5 sec.
Solvent type : Acetone
Recovery : 3hrs of recovery under the standard condition after the test.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-01
23. Thermal shock
Specified Value
CAL45 Type △L/L : Within ±10%
LHL□□□
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30% (LHLP：only △L/L)
FBA/FBR Appearance : No abnormality
Impedance change : Within ±20%
Test Methods and
Remarks
CA：Conditions for 1cycle
Step Temperature (℃) Duration (min.)
1 －25＋0/－3 30±3
2 Room temperature Within 3
3 ＋85＋2/－0 30±3
4 Room temperature Within 3
Number of cycles : 5 cycles
Recovery : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the
measurement within 2hrs.
LHL□□□・FB： According to JIS C0025
Conditions for 1 cycle
Step Temperature (℃) Duration (min.)
1 Minimum operating temperature＋0/－3 30±3
2 Room temperature Within 3
3 Minimum operating temperature＋2/－0 30±3
4 Room temperature Within 3
Number of cycles : 10 cycles 〔LHL□□□〕
Recovery : 5 cycles (FBA, FBR)
: 4 to 24hrs of recovery under the standard condition after the removal from the test chamber. 〔LHL□□□〕
: 3hrs of recovery under the standard condition after the removal from the test chamber. (FBA, FBR)
24. Damp heat
Specified Value
CAL45 Type △L/L : Within ±10%
LHL□□□
FBA/FBR Appearance：No abnormality
Impedance change：Within ±20%
Test Methods and
Remarks
CA :
Temperature : 40±2℃
Humidity : 90～95%RH
Duration : 1000 hrs
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
FB :
Temperature : 60±2℃
Humidity : 90～95%RH
Duration : 1000 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_reli_e-01
25. Loading under damp heat
Specified Value
CAL45 Type △L/L : Within ±10%
LHL□□□
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
Test Methods and
Remarks
CA :
Temperature : 40±2℃
Humidity : 90～95%RH
Duration : 1000 hrs
Applied current : Rated current
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ :
Temperature : 40±2℃
Humidity : 90～95%RH
Duration : 1000±24 hrs
Applied current : Rated current
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
26. Loading at high temperature
Specified Value
CAL45 Type △L/L : Within ±10%
LHL□□□
FBA/FBR
Test Methods and
Remarks
CA :
Temperature : 85±2℃
Duration : 1000 hrs
Applied current : Rated current
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
27. Low temperature life test
Specified Value
CAL45 Type △L/L : Within ±10%
LHL□□□
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
Test Methods and
Remarks
CA :
Temperature : －25±2℃
Duration : 1000 hrs
Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs.
LHL□□□ :
Temperature :－40±3℃
Duration : 1000±24 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
28. High temperature life test
Specified Value
CAL45 Type
LHL□□□
Appearance : No abnormality
Inductance change : Within ±10%
Q change : Within ±30% (LHLP : only △L/L)
FBA/FBR
Test Methods and
Remarks
LHL□□□ :
Temperature : 105±3℃
Duration : 1000±24 hrs
Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_prec_e-01
AXIAL LEADED INDUCTORS（CAL Type）、
RADIAL LEADED INDUCTORS（LH Type）、
LEADED FERRITE BEAD INDUCTORS（ FB Series A Type／R Type）
■PRECAUTIONS
1. Circuit Design
Precautions
◆Operating environment
1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment,
telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical
equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear
control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or
damage. For such uses, contact TAIYO YUDEN Sales Department in advance.
2. PCB Design
Precautions ◆Design
1. Please design insertion pitches as matching to that of leads of the component on PCBs.
Technical
considerations
◆Design
1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will
cause breakage of the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs.
3. Considerations for automatic placement
Precautions
◆Adjustment of mounting machine
1. Excessive impact load should not be imposed on the products when mounting onto the PC boards.
2. Mounting and soldering conditions should be checked beforehand.
Technical
considerations
◆Adjustment of mounting machine
1. When installing products, care should be taken not to apply distortion stress as it may deform the products.
4. Soldering
Precautions
◆Wave soldering
1. Please refer to the specifications in the catalog for a wave soldering.
2. Do not immerse the entire inductor in the flux during the soldering operation.
◆Lead free soldering
1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering
heat, soldering etc sufficiently.
◆Recommended conditions for using a soldering iron:
・Put the soldering iron on the land-pattern.
・Soldering iron's temperature - Below 350℃
・Duration - 3 seconds or less
・The soldering iron should not directly touch the inductor.
◆Reflow soldering
1. As for reflow soldering, please contact our sales staff.
Technical
considerations
◆Lead free soldering
1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently
degrade the reliability of the products.
◆Recommended conditions for using a soldering iron
If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade
the reliability of the products.
5. Cleaning
Precautions
◆Cleaning conditions
1. CAL type, LH type
Please do not do cleaning by a supersonic wave.
Technical
considerations
◆Cleaning conditions
1. CAL type, LH type,
If washing by supersonic waves, supersonic waves may deform products.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_leaded_prec_e-01
6. Handling
Precautions
◆Handling
1. Keep the inductors away from all magnets and magnetic objects.
◆Mechanical considerations
1. Please do not give the inductors any excessive mechanical shocks.
2. LH type
If inductors are dropped onto the floor or a hard surface they should not be used.
◆Packing
1. Please do not give the inductors any excessive mechanical shocks.
In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading /
fragile item).
Technical
considerations
◆Handling
1. There is a case that a characteristic varies with magnetic influence.
◆Mechanical considerations
1. There is a case to be damaged by a mechanical shock.
2. LH type
There is a case to be broken by a fall.
◆Packing
1. There is a case that a lead wire could be deformed by a fall or an excessive shock.
7. Storage conditions
Precautions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the
storage area should be controlled.
Recommended conditions
・Ambient temperature 0～40℃
・Humidity Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may
decrease as time passes.
For this reason, inductors should be used within one year from the time of delivery.
In case of storage over 6 months, solderability shall be checked before actual usage.
Technical
considerations
◆Storage
1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes
and deterioration of taping/packaging materials may take place.
