FTR-1319-3D-DD - Finisar Corporation

Finisar

Product Specification

Long-Wavelength GBIC Transceiver

FTR-1319-3D

Product Features

• Up to 1.25Gb/s bi-directional

data links

• 1310nm Fabry-Perot laser

transmitter

• Optional Digital Diagnostics

• Extended operating temperature

range (-10°C to +85°C)

• Compatible with 3.3 & 5V

systems

• Hot-pluggable (complies with

GBIC specification Rev. 5.5)

• Fully metallic enclosure for low

EMI

• Low power dissipation

Applications

• 1.0625 Gb/s Fibre Channel

• 1.25 Gigabit Ethernet

Finisar’s FTR-1319-3D 1310nm GBIC transceivers comply with GBIC Specification

Revision 5.51. They are compatible with Gigabit Ethernet as specified in IEEE 802.32,

Fibre Channel FC-PH, PH2, PH33 and FC-PI 13.04.

Product Selection

Part Number Digital Diagnostics?

FTR-1319-3D No

FTR-1319-3D-DD Yes

FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 F i n i s a r

I. Pin Out

Pin Name Pin # Sequence

RX_LOS 1 2

GND 2 2

GND 3 2

MOD_DEF(0) 4 2

MOD_DEF(1) 5 2

MOD_DEF(2) 6 2

TX_DISABLE 7 2

GND 8 2

GND 9 2

TX_FAULT

(not supported) 10 2

GND 11 1

-RX_DAT 12 1

+RX_DAT 13 1

GND 14 1

VCC 15 2

VCC 16 2

GND 17 1

+TX_DAT 18 1

-TX_DAT 19 1

GND 20 1

Table 1. GBIC to host connector pin assignment

“Sequence” indicates the order in which pins make contact when the device is hot

plugged. See “Table 3: Signal Definitions” in the GBIC Specification Revision 5.5.1

FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 F i n i s a r

II. Electrical Power Interface

Finisar FTR-1319-3D GBICs have an extended power supply voltage range of 3.15 V to

5.5 V as described in Table 2. They are compatible with both 3.3V and 5 V systems.

Parameter

Symbol Min Typ Max Units Notes/Conditions

Supply Current Is 200 300 mA

Inrush Current Isurge +30 mA Hot plug, above steady

state current.

Absolute Supply Vo ltage Vmax -0.3 6 V Not to be applied

continuosly

Operating Supply Voltag e Vcc 3.15 5.5 V Referenced to GND

Table 2. Electrical power interface

III. Low Speed Signals

RX_LOS and TX_DISABLE are TTL signals as described in Table 3. MOD_DEF(1)

(SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals (see section VIII, “Serial

Communication Protocol”). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to

host_Vcc. For more detailed information, see sections 5.3.1 – 5.3.8 in the GBIC

Specification Rev. 5.51.

Parameter

Symbol Min Max Units Notes/Conditions

GBIC Output LOW VOL 0 0.5 V 4.7k to 10k pull-up to host_Vcc,

measured at host side of connector

GBIC Output HIGH VOH host_Vcc - 0.5 host_Vcc + 0.3 V 4.7k to 10k pull-up to host_Vcc,

measured at host side of connector

GBIC Input LOW VIL 0 0.8 V 4.7k to 10k pull-up to Vcc,

measured at GBIC side of

connector

GBIC Input HIGH VIH 2 Vcc + 0.3 V 4.7k to 10k pull-up to Vcc,

measured at GBIC side of

connector

Table 3. Low speed signals – electronic characteristics

FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 F i n i s a r

Parameter

Symbol Min Typ Max Units Notes/Conditions

RX_LOS Assert Level -- -31 dBm

RX_LOS Deassert Level -- -20 dBm

RX_LOS Hysteresis -- 0.5 dB

RX_LOS Assert Delay t_loss_on 100 µsec From detection of loss of signal

to assertion of RX_LOS

RX_LOS Negate Delay t_loss_off 100 µsec From detection of presence of

signal to negation of RX_LOS

TX_DISABLE Assert Time t_off 10 µsec Rising edge of TX_DISABLE to

fall of output signal below 10%

of nominal

TX_DISABLE Negate Time t_on 1000 µsec Falling edge of TX_DISABLE

to rise of output signal above

90% of nomi nal

TX_DISABLE Reset Time t_reset 10 µsec TX_DISABLE HIGH before

TX_DISABLE set LOW

Table 4. Low speed signal parameters

IV. High Speed Electrical Interface

All high-speed PECL signals are AC-coupled internally.

Parameter

Symbol Min Typ Max Units Notes/Conditions

Data Input Voltage Vin 650 2000 mV PECL differential peak - peak

Data Output Voltage Vout 370 2000 mV PECL different i al peak - pea k

PECL rise/fall tr,tf 260 psec 20%-80% differential

Bit Error Rate BER 10-12 PRBS 27 - 1 test data pattern

Tx Input Impedance Zin 75 Ohm

Rx Output Impedance Zout 75 Ohm

Table 5. High-speed electrical interface

FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 F i n i s a r

V. Optical Parameters

Parameter

Symbol Min Typ Max Units Notes/Conditions

TRANSMITTER CHARACTERISTICS

Transmitter Center Wavelength λc1270 1310 1355 nm

Transmitter Spectral Width ΔλRMS 4 nm RMS. Also meets

curves in FC-PI 10.0

Figures 18.

Transmitter Optical Output Power Pout -9 -6 -3 dBm Average power coupled

into single mode fiber

Transmitter Extinction Ratio OMI 9 dB

Transmitter Eye Opening -- 60 % Conforms to IEEE

802.3 and Fibre

Channel Eye Masks

Transmitter Rise/Fall Time tr /tf 260 ps 20%-80% differential

unfiltered

Total Transmitter Jitter 160 ps Peak to peak, filtered

Relative Intensity Noise RIN -120 dB / Hz

RECEIVER CHARACTERISTICS

Optical Input Wavelength λin 1270 1355 nm

Receiver Reflectance RRX -14 dB

Optical Input Power (1.25 GB/s) Pin -19 -3 dBm

Optical Input Power (1.0625Gb/s) Pin -20 -3 dBm

BER < 10-12 w/ PRBS

27 - 1 test pattern

Total Receiver Jitter 160 ps Peak to peak, filtered in

loopback

Note: Parameters are specified over temperature and voltage, at end of life unless otherwise noted.

Table 6. O

p

tical

p

arameters

VI. General Specifications

Parameter

Symbol Min Typ Max Units Notes/Conditions

Data Rate BR 1.25

1.0625 Gb/sec Fibre Channel, IEEE 802.3

Compatible

Fiber Length L 10,000 m 9μm Core Single Mode Fiber

Fiber Length L 550 m 50μm 500MHz-km Fiber

Fiber Length L 275 m 62.5μm 200MHz-km Fiber

Table 7. General specifications

FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 F i n i s a r

VII. Environmental Specifications

Note that the GBIC Specification requires an ambient temperature range of 0 to 50°C.

The FTR-1319-3D has an extended range from –10°C to +85°C case temperature as

specified in Table 8.

VIII. Serial Communication Protocol

Parameter

Symbol Min Typ Max Units Notes/Conditions

Operating Temp Top -10 85 °C Case Temperature

Relative Humidity RH 0 85 % Non Condensing

Storage Temp Tsto -40 85 °C

Eye Safety -- CDRH and IEC-825 Class 1 Laser

Product. See Note 1

Note 1: Complies with FDA performance standards for laser products except for deviations pursuant to

Laser Notice No. 50, dated July 26, 2001.

Table 8. Environmental specifica tions

All Finisar optical GBICs implement serial identification features described for ‘Module

Definition “4”’ as outlined in Annex D of the GBIC Specification 1. These GBICs use an

Atmel AT24C01A 128 byte E2PROM at address A0H. For details on interfacing with the

E2PROM, see the Atmel data sheet titled “AT24C01A/02/04/08/16 2-Wire Serial CMOS

E2PROM.” 5

Parameter

Symbol Min Typ Max Units Notes/Conditions

I2C Clock for Atmel

(A0H) and Controller

IC (A2H)

Catmel 0 100, 0 00 Hz Bus can be driven blin d

Table 9. I2C timing requirements

FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 F i n i s a r

IX. Mechanical Specifications

Finisar GBICs are compatible with the mechanical specifications outlined in the GBIC

Specification Revision 5.5, Section 61.

Insertion, Extraction, and

Retention Forces

Parameter Symbol Min Typ Max Units Notes/Conditions

GBIC insertion FI0 20 Newtons ~4.5 lbs

GBIC extraction FE0 15 Newtons ~3.3 lbs

GBIC retention FR130 N/A Newtons Straight out ~29.3 lbs

Table 10. Insertion, extraction, and retention forces

Figure 1. GBIC outline drawing

FTR-1319-3D Long-Wavelength GBIC Specification – November 2007 F i n i s a r

X. References

1. “Gigabit Interface Converter (GBIC) Revision 5.5”. Sun Microsystems Computer

Company et. al., August 16, 1999. http://playground.sun.com/pub/OEmod/

2. IEEE Std 802.3. IEEE Standards Department, 2002.

3. “Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”.

American National Standard for Information Systems.

4. “Fibre Channel Draft Physical Interface Specification (FC-PI 13.0). American

National Standard for Information Systems.

5. “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM”. Atmel Corporation.

www.Atmel.com

XI. For More Information

Finisar Corporation

1389 Moffett Park Drive

Sunnyvale, CA 94089-1134

Tel. 1-408-548-1000

Fax 1-408-541-6138

sales@finisar.com

www.finisar.com