May 2018
EMC Components
For general signal line
MMZ0603 0603[0201 inch]*
* Dimensions Code JIS[EIA]
Chip beads
MMZ0603
type
MMZ series
(2/11)
20180521 / beads_commercial_signal_mmz0603_en.fm
EMC Components
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/11)
20180521 / beads_commercial_signal_mmz0603_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
Chip beads
For general signal line
FEATURES
Noise reduction solution for general signal line.
Various frequency characteristics with 4 materials of different features for countermeasures against everything from general signals to
high-speed signals.
APPLICATION
Noise removal for mobile devices such as smartphones and tablet terminals, and various modules.
Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment.
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The Storage temperature range is for after the circuit board is mounted.
Overview of MMZ0603 type
MMZ 0603 S 100 C T 000
Series name L×W×T dimensions Material name Impedance Characteristic
type Packaging style Internal code
(mm) () at 100MHz
0603 0.6×0.3x0.3 D 100 10 C T Taping 000
F 121 120
S
Y
Type
Temperature range Package quantity Individual weight
Operating
temperature
（°C）
Storage
temperature
（°C）(pieces/reel) （mg）
MMZ0603 –55 to +125 –55 to +125 15,000 0.3
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/11)
20180521 / beads_commercial_signal_mmz0603_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603 type
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/11)
20180521 / beads_commercial_signal_mmz0603_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603 type
MATERIAL CHARACTERISTICS
S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in
which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz.
Y material: High frequency range type intended for the 100MHz region and above.
For signal line applications in which the signal frequency is far from the cutoff frequency. Impedance values selected for
effectiveness at 80 to 400MHz.
D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies.
Designed for high impedance at high frequencies (300MHz to 1GHz) for signal line applications.
F material: This new product inherits the characteristic of our D-material, namely its sharp impedance rise time, and its impedance peak
frequency has been shifted higher into range. The product offers excellent noise suppression from 600MHz to as high as in
the GHz range.
TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS
0
200
400
600
800
1000
1200
1400
1600
1800
2000
10 100 1000
Frequency(MHz)
S
D
F
Y
(6/11)
20180521 / beads_commercial_signal_mmz0603_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603 type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
0.3±0.03
0.6±0.03
0.1min.
0.3±0.03
Dimensions in mm
0.30 0.250.25
0.30
(7/11)
20180521 / beads_commercial_signal_mmz0603_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603 type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Impedance DC resistance Rated current Part No.
[100MHz]
()Tolerance ()max. (mA)max.
10 ±50.05 1000 MMZ0603S100CT000
80 ±25% 0.30 200 MMZ0603S800CT000
120 ±25% 0.45 200 MMZ0603S121CT000
240 ±25% 0.57 200 MMZ0603S241CT000
470 ±25% 1.30 100 MMZ0603S471CT000
600 ±25% 1.45 100 MMZ0603S601CT000
75 ±25% 0.35 300 MMZ0603Y750CT000
120 ±25% 0.39 200 MMZ0603Y121CT000
240 ±25% 0.80 200 MMZ0603Y241CT000
470 ±25% 1.40 200 MMZ0603Y471CT000
600 ±25% 1.50 200 MMZ0603Y601CT000
33 ±25% 0.70 200 MMZ0603D330CT000
47 ±25% 0.70 200 MMZ0603D470CT000
56 ±25% 0.95 100 MMZ0603D560CT000
80 ±25% 1.25 100 MMZ0603D800CT000
120 ±25% 1.40 100 MMZ0603D121CT000
10 ±50.50 200 MMZ0603F100CT000
22 ±25% 1.00 200 MMZ0603F220CT000
33 ±25% 1.30 150 MMZ0603F330CT000
Measurement item Product No. Manufacturer
Impedance E4991A+16197 Keysight Technologies
DC resistance Type-7556 Yokogawa
(8/11)
20180521 / beads_commercial_signal_mmz0603_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603 type
ELECTRICAL CHARACTERISTICS
Z VS. FREQUENCY CHARACTERISTICS (BY SERIES)
MMZ0603S-C series MMZ0603Y series MMZ0603D series
MMZ0603F series
0
200
400
800
600
1000
100
300
700
500
900
100001000100101
Frequency (MHz)
Impedance (Ω)
MMZ0603S601C
MMZ0603S471C
MMZ0603S241C
MMZ0603S121C
MMZ0603S800C
MMZ0603S100C
0
100
200
300
400
500
600
700
800
1000
900
100001000100101
Frequency (MHz)
Impedance (Ω)
MMZ0603D800C
MMZ0603D121C
MMZ0603D560C
MMZ0603D330C
MMZ0603D470C
0
200
400
600
800
1000
1200
100001000100101
Frequency (MHz)
Impedance (Ω)
MMZ0603F330C
MMZ0603F220C
MMZ0603F100C
(9/11)
20180521 / beads_commercial_signal_mmz0603_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603 type
ELECTRICAL CHARACTERISTICS
Z, X, R VS. FREQUENCY CHARACTERISTICS
MMZ0603S100CT000 MMZ0603S800CT000 MMZ0603S121CT000
MMZ0603S241CT000 MMZ0603S471CT000 MMZ0603S601CT000
MMZ0603Y750CT000 MMZ0603Y121CT000 MMZ0603Y241CT000
MMZ0603Y471CT000 MMZ0603Y601CT000 MMZ0603D330CT000
MMZ0603D470CT000 MMZ0603D560CT000 MMZ0603D800CT000
01 10 100 1000 10000
20
40
60
80
100
120
140
160
Frequency (MHz)
Impedance (Ω)
Z
X
R
1 10 100 1000 10000
Z
X
R
2
0
4
6
8
10
12
14
16
18
Frequency (MHz)
Impedance (Ω)
01 10 100 1000 10000
50
100
150
200
250
Frequency (MHz)
Impedance (Ω)
Z
X
R
450
400
350
300
250
200
150
100
50
01 10 100 1000 10000
Z
X
R
Frequency (MHz)
Impedance (Ω)
800
600
400
200
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
Z
X
R
1000
800
600
400
200
01 10 100 1000 10000
Z
X
R
Frequency (MHz)
Impedance (Ω)
1 10 100 1000 10000
0
100
200
300
400
500
600
Frequency (MHz)
Impedance (Ω)
Z
X
R
0
50
100
150
200
250
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
Z
X
R
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
50
100
150
200
Z
X
R
1 10 100 1000 10000
0
100
200
300
400
500
600
700
800
900
Frequency (MHz)
Impedance (Ω)
Z
X
R
1 10 100 1000 10000
0
200
400
600
800
1000
Z
X
R
Frequency (MHz)
Impedance (Ω)
1 10 100 1000 10000
0
100
200
300
400
500
Z
X
R
Frequency (MHz)
Impedance (Ω)
1 10 100 1000 10000
0
100
200
300
400
500
600
700
Frequency (MHz)
Impedance (Ω)
Z
X
R
1 10 100 1000 10000
0
100
200
300
400
500
600
700
800
900
Frequency (MHz)
Impedance (Ω)
Z
XR
100
200
300
400
500
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
Z
X
R
(10/11)
20180521 / beads_commercial_signal_mmz0603_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603 type
ELECTRICAL CHARACTERISTICS
Z, X, R VS. FREQUENCY CHARACTERISTICS
MMZ0603D121CT000 MMZ0603F100CT000 MMZ0603F220CT000
MMZ0603F330CT000
1 10 100 1000 10000
0
Frequency (MHz)
Impedance (Ω)
Z
X
R
50
100
150
200
250
300
1 10 100 1000 10000
0
100
200
300
400
500
600
700
Frequency (MHz)
Impedance (Ω)
Z
X
R
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
200
400
600
800
1000
Z
XR
X
1 10 100 1000 10000
0
200
400
600
800
1000
1200
Z
R
Frequency (MHz)
Impedance (Ω)
(11/11)
20180521 / beads_commercial_signal_mmz0603_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603 type
PACKAGING STYLE
REEL DIMENSIONS
TAPE DIMENSIONS
Dimensions in mm
Ty p e A B P1 K
MMZ0603 0.38±0.05 0.68±0.05 2.0±0.05 0.5max.
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
Dimensions in mm
1.0
ø60min.
14.4max.
8.4 +2.0
–0.0
4.0±0.12.0±0.05
B
A P1
8.0±0.3
1.75±0.1
3.5±0.05
K
1.5 +0.1
0
160min. Taping 200min.
300min.
Drawing direction
Dimensions in mm