35
SSG Series 5W/10W/15W/30W/50W/100W/150W
Sanken Switching Power Supply.
SSG Series
SSG Series
The SSG Series utilizes surface-mount components and
an ultra-small TIW (Triple Insulation Wire) transformer to produce a line of
very small, light-weight switching power supplies.
5W, 10W, 15W, 30W, 50W, 100W, 150W
FEATURES
• Firstly adopted newly developped transformer which is equipped with triple
insulation wire (Without barrier tape)
• Pursuing smaller and thinner model
• Increased efficiency 4 to 5% compared with our existing products
• Obtained any applicable safety standards, UL and CSA certificate
• FCC class B application
36
SSG Series 5W/10W/15W/30W/50W/100W/150W
Control
Overcurrent
detection
Overvoltage
detection
Output
voltage
detection
Line
filter
Inrush
current
limiter
Switching
Rectifier Rectifier
and
filter
Operation indicator LED
Output
+S
+
–
–S
V.ADJ
AC 1(L)
AC 2(N)
FG
INPUT
* +S and + are connected with a short bar, as are -S and -.
+S and -S are provided on 100 W and 150 W models.
* Operation indicator LED and overvoltage detection are not
provided on 5 W and 10 W models.
SSG Series circuit diagram
37
SSG Series 5W/10W/15W/30W/50W/100W/150W
Rating
Item Conditions
Rated Input Voltage
Input Voltage Range
Input Current (see Note 1)
Rated Frequency
Frequency Range
Efficiency (typ) (see Note 1)
Inrush Current (see Note 1, 2)
Rated Output Voltage
Adjustable Output Voltage Range
Rated Output Current
Adjustable Output Current Range
Maximum Output Power
Ripple (mVp-p) (see Note 1, 4)
Static Input Range 85 to 132V AC
Static Load Range 0 to 100%
Time Driftt 10min. to 8 hours
Ambient Temperature Range 0 to +50°C
Output Holdup Time (see Note 1)
Startup Time (see Note 1)
Leakage Current (see Note 1)
Over Current Protection
Over Voltage Protection
Remote On/Off Control
Remote Sensing
Temperature Operating Temperature
Storage Temperature
Relative Humidity Operating Humidity
Storage Humidity
Insulation Withstand Voltage Between Input and Output
Between Input and Frame
Between Output and Frame
Insulation Resistance Between Input and Output
Between Input and Frame
Between Output and Frame
Safety Standards
EMI Standards
External Appearance
Size (dimensions in mm)
Weight (without cover)
Input
Note 1: Rated input/output conditions means that the switching power supply is operated under the rated input voltage, rated frequency, rated output voltage, and at an ambient
temperature of 25°C and 60% humidity.
Note 2: At cold start. (More current may flow at restart.)
Note 3: All output characteristics are measured at a point 5 cm from the output connector, with a 63 V 47 µF electrolytic capacitor attached at that point.
Note 4: Ripple noise is measured with a 100 MHz oscilloscope, using a 1:1 probe.
Output (see Note 3)Other
Additional
Functions
EnvironmentalInsulation
Structural
Specifications
Applicable
Standards
5W
SSG 005-05
100-120V AC
85 to 132V AC
0.2 A
50/60 Hz
47 to 440 Hz
68%
30A (max)
5V
Fixed
1A
0 to 100%
5W
150mVp-p
±3%
10ms (min)
10ms
0.5mA (max)
PCB type
50 x 65 x 18
(W x D x H)
50 g
Constant Voltage
Accuracy
10W
SSG 010-05 SSG 010-12 SSG 010-15 SSG 010-24
100-240V AC
85 to 264V AC
0.4/0.23A (typ)
50/60 Hz
47 to 440 Hz
72% 75% 75% 78%
25/50 A (max)
+5V +12V +15V +24V
Rated voltage ±10%
2.0A 0.9A 0.7A 0.45A
0 to 100%
10W 10.8W 10.5W 10.8W
120mVp-p 170mVp-p 200mVp-p 300mVp-p
±3%
10ms (min)
400ms (typ)
0.5mA (max)
PCB type (chassis is optional)
67 x 72 x 20 (W x D x H) (with chassis)
80 g (130 g with chassis)
Detection above 120% of rated current (output cutoff)
Not provided
Not provided
Not provided
0 to 50°C (no cover)
-25 to +85°C
30 to 90% (no condensation)
2000 V AC for 1 minute (Leakage current of 15 mA or less)
500 V AC for 1 minute (Leakage current of 15 mA or less)
100 MΩor more (measured with 500 V DC Megger)
UL and CSA certified
Conforms to FCC Class B
38
SSG Series 5W/10W/15W/30W/50W/100W/150W
Rating
Item Conditions
Rated Input Voltage
Input Voltage Range
Input Current (see Note 1)
Rated Frequency
Frequency Range
Efficiency (typ) (see Note 1)
Inrush Current (see Note 1, 2)
Rated Output Voltage
Adjustable Output Voltage Range
Rated Output Current
Adjustable Output Current Range
Maximum Output Power
Ripple (mVp-p) (see Note 1, 4)
Static Input Range 85 to 132V AC
Static Load Range 0 to 100%
Time Driftt 10min. to 8 hours
Ambient Temperature Range 0 to +50°C
Output Holdup Time (see Note 1)
Startup Time (see Note 1)
Leakage Current (see Note 1)
Over Current Protection
Over Voltage Protection
Remote On/Off Control
Remote Sensing
Temperature Operating Temperature
Storage Temperature
Relative Humidity Operating Humidity
Storage Humidity
Insulation Withstand Voltage Between Input and Output
Between Input and Frame
Between Output and Frame
Insulation Resistance Between Input and Output
Between Input and Frame
Between Output and Frame
Safety Standards
EMI Standards
External Appearance
Size (dimensions in mm)
Weight (without cover)
Input
Note 1: Rated input/output conditions means that the switching power supply is operated under the rated input voltage, rated frequency, rated output voltage, and at an ambient
temperature of 25°C and 60% humidity.
Note 2: At cold start. (More current may flow at restart.)
Note 3: All output characteristics are measured at a point 5 cm from the output connector, with a 63 V 47 µF electrolytic capacitor attached at that point.
Note 4: Ripple noise is measured with a 100 MHz oscilloscope, using a 1:1 probe.
Output (see Note 3)
Other
Additional
Functions
EnvironmentalInsulation
Structural
Specifications
Applicable
Standards
Constant Voltage
Accuracy
15W
SSG 015-05 SSG 015-12 SSG 015-15 SSG 015-24
100-120V AC
85 to 132V AC
0.5A (typ)
50/60 Hz
47 to 440 Hz
72% 75% 75% 78%
30 A (max)
+5V +12V +15V +24V
Rated voltage ±10%
3.0A 1.3A 1.0A 0.7A
0 to 100%
15W 15.6W 15W 16.8W
120mVp-p 170mVp-p 200mVp-p 300mVp-p
±3%
10ms (min)
40ms (typ)
0.5mA (max)
Detection above 120% of rated current (output cutoff)
Detection above 120% of rated voltage (output cutoff)
Not provided
Not provided
0 to 50°C (no cover)
-25 to +85°C
30 to 90% (no condensation)
30 to 90% (no condensation)
2000 V AC for 1 minute, 2400 V AC for 1 second (Leakage current of 15 mA or less)
500 V AC for 1 minute, 600 V AC for 1 second (Leakage current of 15 mA or less)
100 MΩ(measured with 500 V DC Megger)
UL and CSA certified
Conforms to FCC Class B
PCB type,
input and output connectors (chassis and input/output terminal stand are optional)
70 x 92 x 20 (W x D x H)(with chassis)
100 g (150 g with chassis)
39
SSG Series 5W/10W/15W/30W/50W/100W/150W
30W
SSG 030-05 SSG 030-12 SSG 030-15 SSG 030-24
100-120V AC
85 to 132V AC
0.7A (typ)
50/60 Hz
47 to 440 Hz
75% 78% 78% 80%
30 A (max)
+5V +12V +15V +24V
Rated voltage ±10%
6.0A 2.6A 2.0A 1.3A
0 to 100%
30W 30W 30W 31.2W
120mVp-p 150mVp-p 150mVp-p 200mVp-p
±3%
16ms (min)
400ms (typ)
0.4mA (max)
(input/output terminal stand and cover are optional)
75 x 120 x 25 (W x D x H)(with chassis)
250 g (with chassis)
Detection above 120% of rated current (output cutoff)
Detection above 120% of rated voltage (output cutoff)
Not provided
Not provided
Operating Temperature 0 to 50°C (0 to 40°C with cover)
-25 to +85°C
30 to 90% (no condensation)
2000 V AC for 1 minute, 2400 V AC for 1 second (Leakage current of 15 mA or less)
500 V AC for 1 minute, 600 V AC for 1 second (Leakage current of 15 mA or less)
100 MΩ(measured with 500 V DC Megger)
UL and CSA certified
Conforms to FCC Class B
50W
SSG 050-05 SSG 050-12 SSG 050-15 SSG 050-24
100-120V AC
85 to 132V AC
1.3A (typ)
50/60 Hz
47 to 440 Hz
75% 77% 79% 81%
30 A (max)
+5V +12V +15V +24V
Rated voltage ±10%
10.0A 4.2A 3.4A 2.1A
0 to 100%
50W 50.4W 51W 50.4W
120mVp-p 150mVp-p 150mVp-p 200mVp-p
±3%
16ms (min)
400ms (typ)
0.4mA (max)
(input/output terminal stand and cover are optional)
90 x 135 x 25 (W x D x H)(with chassis)
300 g (with chassis)
40
SSG Series 5W/10W/15W/30W/50W/100W/150W
Rating
Item Conditions
Rated Input Voltage
Input Voltage Range
Input Current (see Note 1)
Rated Frequency
Frequency Range
Efficiency (typ) (see Note 1)
Inrush Current (see Note 1, 2)
Rated Output Voltage
Adjustable Output Voltage Range
Rated Output Current
Adjustable Output Current Range
Maximum Output Power
Ripple (mVp-p) (see Note 1, 4)
Static Input Range 85 to 132V AC
Static Load Range 0 to 100%
Time Driftt 10min. to 8 hours
Ambient Temperature Range 0 to +50°C
Output Holdup Time (see Note 1)
Startup Time (see Note 1)
Leakage Current (see Note 1)
Over Current Protection
Over Voltage Protection
Remote On/Off Control
Remote Sensing
Temperature Operating Temperature
Storage Temperature
Relative Humidity Operating Humidity
Storage Humidity
Insulation Withstand Voltage Between Input and Output
Between Input and Frame
Between Output and Frame
Insulation Resistance Between Input and Output
Between Input and Frame
Between Output and Frame
Safety Standards
EMI Standards
External Appearance
Size (dimensions in mm)
Weight (without cover)
Input
Note 1: Rated input/output conditions means that the switching power supply is operated under the rated input voltage, rated frequency, rated output voltage, and at an ambient
temperature of 25°C and 60% humidity.
Note 2: At cold start. (More current may flow at restart.)
Note 3: All output characteristics are measured at a point 5 cm from the output connector, with a 63 V 47 µF electrolytic capacitor attached at that point.
Note 4: Ripple noise is measured with a 100 MHz oscilloscope, using a 1:1 probe.
Output (see Note 3)
Other
Additional
Functions
EnvironmentalInsulation
Structural
Specifications
Applicable
Standards
Constant Voltage
Accuracy
100W
SSG 100-05 SSG 100-12 SSG 100-15 SSG 100-24
100-120V AC
85 to 132V AC
2A (typ)
50/60 Hz
47 to 440 Hz
79% 83% 84% 86%
20 A (max)
+5V +12V +15V +24V
Rated voltage ±10%
20.0A 8.5A 7.0A 4.5A
0 to 100%
100W 102W 105W 108W
120mVp-p 180mVp-p 180mVp-p 240mVp-p
±3%
20ms (min)
300ms (typ)
0.4mA (max)
Detection above 120% of rated current (output cutoff)
Detection above 120% of rated voltage (output cutoff)
Not provided
Provided
Operating Temperature 0 to 50°C (0 to 40°C with cover)
-25 to +85°C
30 to 90% (no condensation)
2000 V AC for 1 minute, 2400 V AC for 1 second (Leakage current of 15 mA or less)
500 V AC for 1 minute, 600 V AC for 1 second (Leakage current of 15 mA or less)
100 MΩ(measured with 500 V DC Megger)
UL and CSA certified
Conforms to FCC Class A
(input/output terminal stand and cover are optional)
93 x 177 x 40 (W x D x H)(with chassis)
470 g (with chassis)
41
SSG Series 5W/10W/15W/30W/50W/100W/150W
150W
SSG 150-05 SSG 150-12 SSG 150-15 SSG 150-24
100-120V AC
85 to 132V AC
3.5A (typ)
50/60 Hz
47 to 440 Hz
79% 83% 84% 86%
20 A (max)
+5V +12V +15V +24V
Rated voltage ±10%
30A 13A 10A 6.5A
0 to 100%
150W 156W 150W 156W
120mVp-p 180mVp-p 180mVp-p 240mVp-p
±3%
20ms (min)
300ms (typ)
0.4mA (max)
Detection above 120% of rated current (output cutoff)
Detection above 120% of rated voltage (output cutoff)
Not provided
Provided
Operating Temperature 0 to 50°C (0 to 40°C with cover)
-25 to +85°C
30 to 90% (no condensation)
2000 V AC for 1 minute, 2400 V AC for 1 second (Leakage current of 15 mA or less)
500 V AC for 1 minute, 600 V AC for 1 second (Leakage current of 15 mA or less)
100 MΩ(measured with 500 V DC Megger)
UL and CSA certified
Conforms to FCC Class A
(input/output terminal stand and cover are optional)
93 x 177 x 57 (W x D x H)(with chassis)
450 g (with chassis)
42
SSG Series 5W/10W/15W/30W/50W/100W/150W
65 ±1.0
2.5max 13.5max 50 ±1.0
42 ±0.54 ±0.5
4 ±0.5 57 ±0.5
7max
7max
2- 4
11.6
1 CN1
CN2
5
φ
1. PCB material is CEM-3 (t1.6 double-sided
through-hole, UL94V-0).
2. Cross-hatched areas in figure indicate
regions where parts may not be mounted.
When mounting the power supply, take
care to maintain board distance. Plastic
spacers, such as KGTS (manufactured by
Kitagawa) may be used.
5 W (PCB type) (weight: 50 g)
Model
SSG005-05
62 ±0.5
4
65 ±1.0
57 ±0.5
4
70 ±1.0
7max
10W (PCB type) 10W (with chassis)
7max
7max
15.5max2.5max
3max
7max3max
63 ±0.5
50 ±0.5
72 ±1.5
62 ±0.56 ±0.5
20±1.0
67 ±1.0
15 ±0.5
11 ±0.5
5 ±0.5
2- 3.25 ±0.2
φ
M3 (2, for mounting)
M3 (2, for mounting)
CN2
CN1
CN2
CN1
1. PCB material is CEM-3 (t1.6, UL94V-0).
2. Chassis material is SPCC (t1.0, MFZn II-
a3).
3. The chassis is optional.
4. Mounting screws should be shorter than 4
mm (including chassis thickness).
10 W (PCB type) (weight: 80 g) / 10 W (with chassis) (weight: 130 g)
Model
SSG010-05
SSG010-12
SSG010-15
SSG010-24
1. PCB material is CEM-1 (t1.6, UL94V-
0).
2. Cross-hatched areas in figure indicate
regions where parts may not be
mounted.
43
SSG Series 5W/10W/15W/30W/50W/100W/150W
65 ±0.5
92 ±1.0
20 ±1.0
80 ±0.5 5 ±0.5
2-M3
5 ±0.5
10 ±0.5 70 ±1.0
45 ±0.510 ±0.5
M3 (2, for mounting)
(maximum screw length 4mm)
LED (operation indicator)
CN2
CN1
80 ±0.5
65 ±1.0
57 ±0.5
4 ±0.5
4 ±0.5 90 ±1.0
8max
2.5max
15.5
max
1.6
7max
3- 3.2 ±0.2
7max 7max
8max
7max
–V
+V
AC (L)
AC (N)
FG
M3
(16)
φ
LED (operation indicator)
View with input/output terminal stand attached
CN2
CN1
1. PCB material is CEM-3 (t1.6, UL94V-0).
2. Cross-hatched areas in figure indicate
regions where parts may not be mounted.
15 W (PCB type) (weight: 90 g)
Model
SSG015-05
SSG015-12
SSG015-15
SSG015-24
1. PCB material is CEM-1 (t1.6, UL94V-0).
2. Chassis material is SPCC (t1.0, MFZn II-a3).
3. The chassis is optional.
4. Mounting screws should be shorter than 4 mm
(including chassis thickness).
15 W (with chassis) (weight: 150 g)
Model
SSG015-05
SSG015-12
SSG015-15
SSG015-24
44
SSG Series 5W/10W/15W/30W/50W/100W/150W
120 ±1
6914
(13)
15
25 ±1.0
29 ±1.0
25±1.0
65 22
39
75 ±1.0
–V
+V
AC (L)
AC (N)
FGM3
LED (operation indicator)
View with input/output terminal stand attached
M3 (2, for mounting)
M3 (2, for mounting)
Output voltage
adjustment knob
CN2
CN1
CN3
1. Chassis material is aluminum t1.5.
2. Cover material is SPCC MFZnP II-a3 t0.8.
3. PCB material is CEM-3 t1.6, single-sided
(UL94V-0).
4. Mounting screws should be shorter than 5
mm (including chassis thickness).
30 W (weight: 250 g)
Model
SSG030-05
SSG030-12
SSG030-15
SSG030-24
135 ±1.0
139 ±1.0
96
75 22
96
13
29 ±1.0
25 ±1.0
15 90 ±1.0
94 ±1.0
–V
+V
AC (L)
AC (N)
FG
M3
10
CN2
CN1
CN3
LED (operation indicator)
View with input/output terminal stand attached
M3BR
(2, for mounting)
M3BR
(2, for mounting)
Output voltage
adjustment knob
50 W (weight: 300 g)
Model
SSG050-05
SSG050-12
SSG050-15
SSG050-24
45
SSG Series 5W/10W/15W/30W/50W/100W/150W
SSG100-
100 ±0.5
100 ±0.5
7-M4 29 ±0.3 160 ±1.0
94 ±1.0
93 ±1.0
45 ±0.3
12.5
10
8.6
CAUTION
(17)
(14)
15 ±0.3
25 ±0.3
40 ±1.0
44 ±1.0
(–S)
(–)
(+)
(+S)
(AC-L)
(AC-N)
(FG)
LED (operation indicator)
M4 (2, for mounting)
M4 (2, for mounting)
Output voltage
adjustment knob
Chassis
100 W (weight: 470 g)
Model
SSG100-05
SSG100-12
SSG100-15
SSG100-24
100 ±0.5
9-M4 177 ±1.0
94 ±1.0
93
12.2
10
8.6
(17)
(15.6) (15)
21.5 ±0.3
30 ±0.3
25 ±0.3
17.5 ±0.3
57
61 ±1.0
(–S)
(–)
(+)
(+S)
(AC-L)
(AC-N)
(FG)
LED (operation indicator)
M4 (3, for mounting)
Output voltage
adjustment knob
Chassis
150 W (weight: 830 g)
Model
SSG150-05
SSG150-12
SSG150-15
SSG150-24
46
SSG Series 5W/10W/15W/30W/50W/100W/150W
Model
Input
(for all models
listed above)
SSG005-05
SSG010 type
SSG015 type
Pin
1
2
3
4
5
1
2
1, 2
3, 4
Name
FG
NC
AC (N)
NC
AC (L)
+V
0V
+V
0V
Corresponding
Connector
XHP-5 (JST)
XHP-2
(JST)
XHP-4
(JST)
Corresponding
contacts
SXH-001T-P0.6
(JST)
SXH-001T-P0.6
(JST)
SXH-001T-P0.6
(JST)
Connector
CN1
CN2
CN2
Connectors (for models SSG005, SSG010, and SSG015)
Input
Output
AC input terminals. Connect the neutral line to AC
(N). AC (L) has an input fuse.
Ground terminal. Connect to a ground wire.
DC output terminals. Use these terminals for
connection to the load.
Remote sensing terminals. For remote sensing,
connect these terminals to the sensing point.
AC (N)
AC (L)
FG
+V
0 V
+S
-S
Terminal names and functions
Model
Input
(for all models
listed above)
SSG030 type
SSG050 type
Pin
1
2
3
4
5
1, 2
3, 4
1
1 - 3
4 - 6
1
Name
FG
NC
AC (N)
NC
AC (L)
+V
0V
FG
+V
0V
FG
Corresponding
Connector
VHR-5N (JST)
VHR-4N (JST)
VHR-6N (JST)
Corresponding
contacts
SVH-21T-P1.1
(JST)
SXH-001T-P0.6
(JST)
SXH-001T-P0.6
(JST)
Connector
CN1
CN2
CN3
CN2
CN3
Connectors (for models SSG030, SSG050)
FG#250 fastener recepticle
FG#250 fastener recepticle
Model
SSG030 type
SSG050 type
SSG100 type
SSG150 type
Pin
1
2
3
4
5
1
2
3
4
5
6
7
Name
FG
AC (N)
AC (L)
+V
0V
FG
AC (N)
AC (L)
+S
+V
0V
-S
Corresponding crimp terminal
V1. 25-3 (JST) or equivalent
V2-4 (JST) or equivalent
Terminal Stand (for models SSG030, SSG050, SSG100, and SSG150)
Note: Check the diagram for each model to verify terminal arrangement.
