DC/DC Converters TES 2N Series, 2 Watt CB Features Low profile SMD-package Wide 2:1 input voltage range I/O isolation 1500 VDC Input filter meets EN55022, class A Operating temperature range Scheme UL 60950-1 -40C to +85C Short-circuit protection Qualified for leadfree reflow solder process according IPC J-STD-020C Available in tape and reel package 3-year product warranty The TES-2N series is a family of high performance 2W DC/DC converter modules featuring wide 2:1 input voltage ranges. The 28 models come in a low profile SMD package which requires just 3 cm2 space on the PCB. A high efficiency allows an operating temperature range of -40C to +85C. A built-in EMI input filter complies with EN 55022, class A. Typical applications for these converters are battery operated equipment, instrumentation, communication and industrial electronics, everywhere where isolated, tightly regulated voltages are required. Models Ordercode TES 2N-0510 TES 2N-0511 TES 2N-0512 TES 2N-0513 TES 2N-0521 TES 2N-0522 TES 2N-0523 TES 2N-1210 TES 2N-1211 TES 2N-1212 TES 2N-1213 TES 2N-1221 TES 2N-1222 TES 2N-1223 TES 2N-2410 TES 2N-2411 TES 2N-2412 TES 2N-2413 TES 2N-2421 TES 2N-2422 TES 2N-2423 TES 2N-4810 TES 2N-4811 TES 2N-4812 TES 2N-4813 TES 2N-4821 TES 2N-4822 TES 2N-4823 http://www.tracopower.com Input voltage range 4.5 - 9.0 VDC (nominal 5 VDC) 9 - 18 VDC (nominal 12 VDC) 18 - 36 VDC (nominal 24 VDC) 36 - 75 VDC (nominal 48 VDC) Output voltage Output current max. Efficiency typ. 3.3 VDC 5 VDC 12VDC 15 VDC 5 VDC 12 VDC 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC 5 VDC 12 VDC 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC 5 VDC 12 VDC 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC 5 VDC 12 VDC 15 VDC 500 mA 400 mA 165 mA 135 mA 200 mA 85 mA 65 mA 500 mA 400 mA 165 mA 135 mA 200 mA 85 mA 65 mA 500 mA 400 mA 165 mA 135 mA 200 mA 85 mA 65 mA 500 mA 400 mA 165 mA 135 mA 200 mA 85 mA 65 mA 70 % 73 % 75 % 73 % 64 % 69 % 71 % 73 % 77 % 80 % 80 % 73 % 78 % 78 % 72 % 77 % 80 % 81 % 74 % 78 % 80 % 71 % 73 % 79 % 79 % 71 % 77 % 77 % Page 1 of 3 DC/DC Converters TES 2N Series 2 Watt Input Specifications Input current at full load (nominal input) 5 12 24 48 Vin Vin Vin Vin models: models: models: models: 600 mA typ. 220 mA typ. 110 mA typ. 55 mA typ. Surge voltage (100 msec. max.) 5 12 24 48 Vin Vin Vin Vin models: models: models: models: 11 V max. 25 V max. 50 V max. 100 V max. Conducted noise (input) EN 55022 level A, FCC part 15, level A Output Specifications Voltage set accuracy 2 % - Input variation Vin min. to Vin max. 0.5 % max. - Load variation 25 - 100 % 0.75 % max. dual output models: 2.0 % (balanced load) Regulation Ripple and noise (20 MHz Bandwidth) 50 mVpk-pk max Temperature coefficient 0.02 %/K Short circuit protection indefinite, automatic recovery Minimum load 25 % of rated max current (operation at lower load condition is safe but a higher output ripple will be experienced) Capacitive load 3.3 5 12 15 5 12 15 VDC VDC VDC VDC VDC VDC VDC output output output output output output output models: 2200 F max. models: 1000 F max. models: 170 F max. models: 110 F max. models: 470 F max. models: 100 F max. models: 47 F max. General Specifications Temperature ranges - Operating -40C to +85C - Storage -55C to +125C Derating 3.5 %/K above +71C Humidity (non condensing) 95 % rel. H max. Reliability, calculated MTBF (MIL-HDBK-217F, at +25C, ground benign) >1.0 Mio h Isolation voltage (60sec.) - Input/Output 1500 VDC Isolation capacitance - Input/Output 250 pF Isolation resistance - Input/Output (500 VDC) >1000 M Ohm Switching frequency 300 kHz (PFM) Safety standards UL 60950-1, IEC/EN 60950-1 Safety approvals and certifications - CB certificate (IEC 60950-1) www.tracopower.com/products/tes2n-cb.pdf - CSA (File No. 226037) http:directories.csa-international.org All specifications valid at nominal input voltage, full load and +25C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TES 2N Series 2 Watt Physical Specifications Casing material DAP (UL94V-0 rated) Weight 3.8 g (0.13oz) Lead-free reflow solder process as per J-STD-020D.01 (to find at: www.jedec.org - free registration re quired) Moisture sensivity level (MSL) level 2 as per J-STD-033B.01 (to find at: www.jedec.org - free registration required) Washing process www.tracopower.com/products/smd- wash.pdf Packaging www.tracopower.com/products/tes2n-pack.pdf Outline Dimensions 8.0 (0.31) 0.25 (0.01) 24.0 (0.94) 0 - 4 0.15 1.0 (0.04) 9 top view 1 3.11 (0.12) 7 Pin-Out 18.1 (0.71) 10 13.7 (0.54) 16 8 15.24 (0.60) 2.54 (0.10) Pin Single Dual 1 -Vin (GND) -Vin (GND) 7 No con. No con. 8 No con. Common 9 +Vout +Vout 10 -Vout -Vout 16 +Vin +Vin 2.8 3.11 (0.12) 15.24 (0.60) (0.11) 13.7 (0.54) 2.8 Solder Pad Dimension (0.11) 1.4 (0.055) min. 2.54 (0.10) Dimensions in [mm], () = Inch Tolerances 0.25 (0.01) Pin pitch tolerances 0.05 (0.002) Specifications can be changed any time without notice. Rev. 11/11 Jenatschstrasse 1 * CH-8002 Zurich * Switzerland Tel. +41 43 311 45 11 * Fax +41 43 311 45 45 * info@traco.ch * www.tracopower.com Page 3 of 3