REVISION BE CLM-1XX-XX-XX-D-XX OPTION -P: PICK & PLACE PAD (AVAILABLE ON POS 7 THRU 50 ONLY) (SEE FIG 3, SHT 2)(USE LMP-04) -TR: TAPE & REEL -BE: BOTTOM ENTRY ONLY (SEE FIG 2)(USE CLM-XX-DBE-XX) -PA: PICK & PLACE PAD W/ ALIGNMENT PINS (SEE FIG 4, SHT 2) -A: ALIGNMENT PIN (USE CLM-XX-D-XX) (AVAILABLE ON POS 3 THRU 50 ONLY) (SEE FIG 5, SHT 2) -K: POLYIMIDE FILM PAD (AVAILABLE ON POS 7 THRU 50 ONLY) (.005 [.13] THICKNESS)(SEE FIG 6, SHT 2) (USE K-DOT-.138-.250-.005) No OF POSITIONS / ROW -02 THRU -50 DO NOT SCALE FROM THIS PRINT FIG 2 (SAME AS FIG 1 EXCEPT INSULATOR) C (No OF POS. X .03937[1.0000] + .0125[.318]) .008 (SEE NOTE 3 AND 7) (SEE NOTE 8) CL C-117-01-X .0394 1.000 .0110 0.279 x .0050[.127] REF No. OF POS x .03937[1.0000] - .03937[1.0000] REF 2 MAX SWAY (ANY DIRECTION) LEAD STYLE SPEC -02: SURFACE MOUNT (USE C-117-01-X) PLATING SPECIFICATION -F: 3" FLASH SELECTIVE GOLD IN CONTACT AREA MATTE TIN ON TAIL (PRE-PLATED CONTACT) -L: 10" LIGHT SELECTIVE GOLD IN CONTACT AREA MATTE TIN ON TAIL (PRE-PLATED CONTACT) -G: 10" GOLD IN CONTACT AREA 3" ON TAIL (POST-PLATED CONTACT) -H: 30" HEAVY GOLD IN CONTACT AREA 3" ON TAIL (POST-PLATED CONTACT) -LM: 10" LIGHT SELECTIVE GOLD IN CONTACT AREA MATTE TIN ON TAIL (PRE-PLATED CONTACT) -FM: 3" FLASH SELECTIVE GOLD IN CONTACT AREA MATTE TIN ON TAIL (PRE-PLATED CONTACT) BODY SPEC -D: DOUBLE ROW (USE CLM-XX-D) .1000 2.540 REF C-117-01-X "A" .0835 2.121 REF C FIG 1 .0885 2.248 (MEASURED AT BEND) C SEE NOTE 9 +1 3 -3 "A" .150.010 3.810.254 (SEE NOTE 5) C BURR SIDE (SEE NOTE 5) SECTION "A"-"A" SCALE 4 : 1 NOTES: 1. C REPRESENTS CRITICAL DIMENSION. 2. MINIMUM PUSHOUT FORCE: .5 LB. 3. WILL LOSE A POSITION FOR EVERY CUT MADE ON A SOCKET STRIP. 4. POSITIONS -05 THROUGH -50 ARE TO BE TUBED. POSITIONS -02 THRU -04 TO BE LAYER PACKAGED ONLY. 5. SHEAR TAILS TO DIMENSIONS SHOWN, .003 MAX SHEAR BURR. 6. PARTS TO BE SYMMETRICAL ABOUT CL . 7. CUT FLASH TO BE .010 [.25] MAX WITH NO FLASH ALLOWED IN HOLES OR EXTENDING BELOW LEADS. 8. ENDWALL AFTER CUTTING: .0155.0025 [.398.064] 9. COPLANARITY TO BE .0040 FOR POSITIONS 2-25 & .0060 FOR POSITIONS 26-50. UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. TOLERANCES ARE: DECIMALS ANGLES .XX: .01 [.3] 2 .XXX: .005 [.13] .XXXX: .0020 [.051] MATERIAL: PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING BODY: LCP, UL 94 VO COLOR: BLACK TERMINAL: PHOS BRONZE F:\DWG\MISC\MKTG\CLM-1XX-XX-XX-D-XX-MKT.SLDDRW SHEET SCALE: 2:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail info@SAMTEC.com code 55322 DESCRIPTION: LOW PROFILE 1MM x 1MM DOUBLE ROW BODY DWG. NO. CLM-1XX-XX-XX-D-XX BY: G. PURVIS 08/10/94 SHEET 1 OF 2 REVISION BE FIG 5 -A: MOLDED ALIGNMENT PIN FIG 3 -P: PICK & PLACE PAD AVAILABLE ON POSITIONS 7 THRU 50 ONLY -PACKAGING (SEE NOTE 4) TABLE 2 (INCLUDES -D & -D-BE) "N" .0966 2.454 .225 5.72 REF CL OPTION .144 3.66 REF .020 0.51 REF (No OF POS. -2) x .03937 [1.0000] LMP-04 "Q" .015 0.38 REF TUBE PLUG -P, -A-P PT-CLX001-D TP-33 -PA PT-CLP001-PA TP-09 -NONE -A, -A-K, -K PT-1-24-01-50 TP-33 .020 0.51 NOTE: "N" = USED MEASURED DIMENSION (REF) "Q" = {("N" - .225[5.72]) / 2} .020[.51] FIG 4 -PA: PICK & PLACE PAD WITH ALIGNMENT PINS .1185 3.010 "M" .0535 1.359 REF .035 0.89 (TYP) "A" C "P" CL .325 8.26 REF CL CL FIG 6 -K: POLYAMIDE FILM PAD AVAILABLE ON POSITIONS 7 THRU 50 ONLY PT-CLX001-D "R" "S" .019.010 0.480.25 .275 6.99 PT-CLP001-PA .0935 2.375 REF .138 3.50 PPP-39-X-X-XX POS / ROW "A" 4-15 16-50 .140[3.58] REF .280[7.11] REF NOTE: "R" = USED MEASURED DIMENSION (REF) "S" = {("R" - .138[3.50]) / 2} .020[.51] TABLE 1 "M" "P" USED MEASURED DIMENSION(REF) POSITIONS EVEN ODD TABLE 3 4-14 16-50 5-15 17-49 {("M" - "A") / 2} .010[.25] PAD PPP-39-E-4-15 PPP-39-E-16-50 PPP-39-O-4-15 PPP-39-0-16-50 F:\DWG\MISC\MKTG\CLM-1XX-XX-XX-D-XX-MKT.SLDDRW PT-1-24-01-50 PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING SHEET SCALE: 4:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail info@SAMTEC.com code 55322 DESCRIPTION: LOW PROFILE 1MM x 1MM DOUBLE ROW BODY DWG. NO. CLM-1XX-XX-XX-D-XX BY: G. PURVIS 08/10/94 SHEET 2 OF 2