STANDARD Resistive Touch Panel Specification 554 4-Wire Series RoHS compliant Panel Drive change over switch Input Panel MCU Interface Control Section A/D converter Noise Filter n FEATURES * Superior quality standard 4 wire resistive analog touch panel * Excellent specification and high quality - Anti Newton ring technology - High reliability materials * Pen/finger type * Transparency - 80% typical * RoHS compliant n PART NUMBERS Touch Panels: Part Number Size Type Part Number Size Type 17.0" Pen/Finger T010-1301-T320 7.0" Pen/Finger (82%, AS) N010-0554-T902 15.0" Pen/Finger N010-0514-T003 6.5" Pen/Finger (W 16:9, Automotive, N010-0554-T813 12.1" Pen/Finger (AS, DPET) N010-0514-T005 6.5" Pen/Finger (W 16:9, Automotive, N010-0554-T814 12.1" Pen/Finger T010-1301-T350 6.5" Pen/Finger (W 16:9) N010-0554-T805 12.1" Pen/Finger N010-0518-T342 6.4" Pen/Finger (78% polarized) N010-0554-T351 10.4" Pen/Finger (86%, AS) N010-0554-T048 6.4" Pen/Finger (86% clear) N010-0554-T352 10.4" Pen/Finger (82%, AS) N010-0554-T043 6.4" Pen/Finger (80%, AG) N010-0554-T347 10.4" Pen/Finger N010-0554-T009 5.7" Pen/Finger T010-1201-T200 Pen/Finger (86%, Clear) N010-0554-T015 82%, AS) 88%, AS) N010-0516-T104 10.4" N010-0519-T742 8.4" Pen/Finger (86% Clear) N010-0554-T241 4.3" 5.7" Pen Finger (86%, AS, DPET) Pen/Finger N010-0554-T504 8.4" Pen/Finger (0.7mm glass) N010-0556-T408 3.9" Pen/Finger (86% Clear) N010-0554-T511 8.4" Pen/Finger (1.1mm glass) N010-0554-T703 3.8" Pen/Finger N010-0516-T947 8.1" Pen/Finger (1.1mm glass) N010-0516-T407 3.7" Pen/Finger (0.7mm glass) N010-0514-T101 7.0" Pen/Finger (W 16:9, Automotive, 82%, AS, 50mm tail) n PART NUMBERS Interface Controller Chips: n PART NUMBERS Controller Boards: Part Number Type Part Number Type N16B-0558-B270 4-Wire, RS232 N010-0559-V036 4-Wire, RS232 N16B-0558-B730 4-Wire, USB NC41120-0018 4-Wire, USB 554 SERIES n DIMENSION EXAMPLE (10.4" SHOWN) (8.00) (8.70) 9.50 Anti-input area (10.00) 228.20 216.20: Transparent area 4.00 214.80: Boundary line of the top enclosure 213.20 212.20: Guaranteed active area 4.70 5.50 Anti-input area 6.00 6.70 162.00: Boundary Line of top enclosure 87.70 159.40: Guaranteed Active Area 160.40 164.60: Transparent Area 175.40 5.40 8.00 7.50 Bottom 6.70 75.001.0 Right Left 8.00 7.50 Antiinput area 4.00 26.50 15.00 #4 10.20 #1 87.700.1 5.000.5 Top 5.40 112.10 Unit: mm n DETAILED SPECIFICATION n 1.0 APPLICATION This specification applies to the standard FID-554 seriesTouch Panel (Pen/Finger type). n 2.0 ADDITIONAL APPLICATIONS Complete specification document is available upon request for customers with whom we have an approved NDA in place. n 3.0 DESCRIPTION AND BLOCK DIAGRAM This panel in combination with a control IC chip is used to transfer the co-ordinates of the touched position to the host system (see block diagram above). n 4.0 DRAWING (Please see the diagram above.) A Definitions of the major dimensions indicated on this diagram: Effective Input Area (A) Area guaranteed to meet all the B characteristics detailed in this specification Anti-input Area (C) An insulating area allowed to protect the touch panel from giving false C readings when an enclosure touches the panel. (See fixing instructions) n 5.0 CHARACTERISTICS Force n 5.1 MECHANICAL Operating Force 0.05~0.49 N (5 ~ 50gF) Measured with a Silicon Measurement Rod R 8 (Round type 8mm) Silicon Rubber Hardness 60C Hardness of Surface Pencil hardness 3H minimum against specification JIS K-5400 Silicon Rubber Rod n 5.2 OPTICAL Transparency Haze 78% min. measured in the effective input area to JIS K 7105 using a MURAKAMI SHIKISAI KENKYUSHO type IIR 100 meter. 5% type measured in the effective input area using a MURAKAMI SHIKISAI KENKYUSHO type IIR 100 meter with an Anti Glare treated 554 SERIES n 5.3 ELECTRICAL DC 7V max. 300 to 850 (at the connector) 100 to 600 (at the connector) 20ms min when using the silicon rubber measurement rod 10M minimum at 25KV DC No problems when at 25KV DC for 1 minute 2% max. Note 1: Measurement condition of linearity is corrected within the control IC. In general the location accuracy is specified as follows: Actual co-ordinate point - theoretical co-ordinate point = location accuracy. In general a 9 point co-ordinate calibration system is used to adjust the micro controller accuracy. (20 point can be used in combination with an EEPROM design). n Co-ordinate Point Rated Voltage: Resistance X axis: Resistance Y axis: Switch Bounce (Chattering): Insulation resistance: Dielectric Strength: Linearity: Theoretical Error Actual Distance 5.4 ENVIRONMENTAL Operating Temperature (*): Storage Temperature: Operating Humidity: Storage Humidity: Chemical Resistance: Low Air Pressure: -5C to 60C -20C to 70C 20% to 85% RH with a Maximum wet bulb temperature of 38C 10% to 90% RH with a Maximum wet bulb temperature of 38C Coating with the following chemicals and storing at room temperature for 2 hours gives no problems. 10% NaCl-water solution, ethyl-acetate, ethyl- alcohol, toluene, methyl-ethyl-ketone No issues down to 0.5 x Normal Air pressure n 5.5 PEN LIFE o2.0 o6.0 0. 8 9.0 1.0 3.5 o2. 0 R 110.01.0 3.0 Effective input area 9 mm Notes 10mm o 4.6 Note taking life: 100,000 words minimum Input life : 1,000,000 times minimum Note 1: Words are written in the notes area and the size of the word is 7.5mm x 6.75mm. A word is any Alphabet / Number / Mark. The pen is as shown below and applies a force of 250g. A failure is judged to happen when the current consumption or insulation resistance or dielectric strength are not met as shown in 5.3. The location accuracy with 9 point calibration must be 4.4 mm max. 1.5 554 SERIES n 5.6 FINGER LIFE A finger is simulated by a silicon rubber plunger R8 (Round type 8mm size) hardness 60C at 200g at frequency 5Hz. A failure is judged to happen when the current consumption or insulation resistance or dielectric strength are not met as shown in 5.3. The location accuracy with 9 point calibration must be 4.4 mm max. Operating force is 150g max. n 5.7 INFORMATION ON THE PANEL Production year 99 00 etc. 9 0 1 The left side number shows production year, eg 1999 0 1 2 The left side number shows production year, eg 2000 [ . . . . . . . . . . .] [ . . . . . . . . . . . ] The first dot after the space shows production month, eg May The first dot after the space shows production month, eg June n 6 PACKAGING n 6.1 PACKING SPECIFICATION Vibration: Drop test: After the test no glass: 10~55 Hz at 1 Octave per minute 10G 20 cycles with one side 0.75mm 60cm Drop 1 corner, 3 crease lines and 6 faces. 1 each 1 time flaw or crack is seen, and no dent or scratch on the film. Also glass and film must not separate. n 6.1 PACKING DETAILS Each touch panel is placed into a plastic bag and is held in place by a slit cut into the side of the cardboard. A second insertion piece is placed into the carton to again add stability. The qty is written on the side of the box. For example the N010-0554T001 has 80 pieces per box. Insert Touch panel with bag Slit in cardboard 550 Type panel illustrated (554 type packed a similar way) 554 SERIES n 7.0 REJECT CRITERIA Description Area 0.1mm2 Area 0.05mm2 & area < 0.1mm2 Area < 0.05mm2 : to be zero : to be max. 5 points : none specified Dot type Area > 0.1mm2 Area 0.05mm2 & area < 0.1mm2 Area < 0.05mm2 : to be zero : to be max. 5 points : none specified Line type Area > 0.1mm Area 0.03mm & width <0.1mm and length < 10mm Area < 0.05mm : to be zero : to be max. 1 point : none specified Film Dent Foreign material between glass and film Reject Criteri a Scratch Dot blur or hard coat missing Newton Ring Glass flaw Area 0.1mm : to be zero Area 0.03mm & width <0.1mm with length < 80mm : to be max. 1 point Area < 0.03mm & width <0.1mm with length < 30mm : none specified Area 0.5mm2 Area 0.03mm2 & area < 0.5mm2 Area < 0.05mm2 : to be zero : to be max. 5 points : none specified These must not be seen from Panel film side under a fluorescent lamp (3 wavelength type lamp). Not to be verified form glass side. To be no flaw which is bigger than that shown in the following diagram. The number of flaws is not specified. 3mm 5mm 2mm 2mm n 8.0 GENERAL POINTS OF CAUTION Touch panels are made of glass, so care must be taken in handling them. Do not stress, pile, bend, lift by the cable or put any stress on the film, for example moving by film face vacuum. In order to clean wring dry a cloth which has been emersed in a natural detergent. DO NOT use any organic solvent, acid or alkali solution. Watch the edge of the panel when cleaning, again for safety reasons. 554 SERIES n 9.0 CONNECTION AND MOUNTING #1 5.0 0.1 1.0 x 3 = 3.0 0.1 0.7 0.1 #4 The details below indicate the recommended mounting structure for panel and enclosure. The enclosure support to fix the touch panel must be over 1.0mm I width and must be outside the view (Transparent area). Also ensure that the enclosure does not cause miss input by touching the view area. The following diagram shows that the enclosure edge must be between the View area and the guaranteed active area. Ensure space is allocated for the diodes, and we recommend that the material to fix the panel and enclosure is elastic. Special design would be required to stop water ingress. The corners of the touch panel are conductive so do not touch any metal parts after mounting. Top View (Picture, with conductive side down) Location Detect 1. Bottom Stiffener board 10.2 2. Left 5.1 3. Top 4. Right (Mating connector type FCI or equivalent SFW4R-1STAE1-LF: for FPC) (Drawing) with conductive connector and glass side down. See page 1 for detail of connector exit side which is left. Transparent Area Anti-input Area 0.8 mm min. Input Area Upper Case Shock absorber to protect the panel (eg rubber) Wiring Area Input Panel 1.0 to 3.0 mm View Area LCD Shock absorber for protection Connector Circuit Board 554 SERIES Stiffener Board Conductive Face Thickness of Glass 1.1mm 1.40 0.2 0.30 0.05 n 10.0 PANEL THICKNESS (typical) Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141 8630, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@fcl.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ (c)2007 Fujitsu Components America, Inc. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. Fujitsu Components America or its affiliates do not warrant that the content of datasheet is error free. In a continuing effort to improve our products Fujitsu Components America, Inc. or its affiliates reserve the right to change specifications/datasheets without prior notice. Rev. October 30, 2007.