HRF-SW1001
________________________________________________________________________________________________________
Web Site: www.mysoiservices.com Honeywell
Email: mysoiservices@honeywell.com Solid State Electronics Center
SPDT Absorptive RF Switch
Features
x High Isolation Of > 40 dB @ 2 GHz
x Low Insertion Loss Of 1.1dB @ 2 GHz
x DC To 2.5 GHz Operating Frequency
x Integrated CMOS Control Logic
x Integrated ESD Protection on Digital I/O
x Single Positive Supply Voltage
x Ultra Small LPCCTM Packaging
x Impedance matched for 75 Ohm systems
Product Description
The Honeywell HRF-SW1001 is a high performance
single pole double throw (SPDT) absorptive RF switch
that is ideal for use in wireless basestation and handset
applications that require minimum power and minimum
insertion loss.
The HRF-SW1001 is manufactured with Honeywell's
patented Silicon On Insulator (SOI) CMOS technology,
which provides the performance of GaAs with the
economy and integration capabilities of conventional
CMOS technology.
HRF-SW1001 in LPCCTM Package
RF Electrical Specifications @ + 25oC
Results @ Vdd=5.0 =/- 10%, Vss = 0 unless otherwise stated, Z0=75 ohms
Parameter Test Condition Frequency Minimum Typical Maximum Units
Insertion Loss* DC – 0.5 GHz
2.0 GHz
2.5 GHz
0.8
0.9
1.1
1.1
1.4
1.5
dB
dB
dB
Isolation* DC – 0.5 GHz
2.0 GHz
2.5 GHz
52
45
41
55
49
44
dB
dB
dB
VSWR* DC – 0.5 GHz
2.0 GHz
2.5 GHz
1.1:1
1.2:1
1.3:1 1.4:1
Ratio
Ratio
Ratio
1dB Compression* Input Power
Vss=Gnd
Vss= -3
1.0 GHz
1.0 GHz
21
29
dBm
dBm
Input IP3* Two-Tone Inputs Up To + 5 dBm
Vss=Gnd
Vss= -3
2.0 GHz
2.0 GHz
35
35
dBm
dBm
Trise, Tfall*
Ton, Toff
Transients
10% To 90%
50% Cntl To 90%/10%Rf
In-Band
10
20
10
nS
nS
mV
*Guaranteed by design
12001 State Highway 55
2002 1001W Published February 2003 Page 1 Plymouth, Minnesota 55441-4799
1-800-323-8295
HRF-SW1001
_______________________________________________________________
Web Site: www.mysoiservices.com Honeywell
Email: mysoiservices@honeywell.com Solid State Electronics Center
12001 State Highway 55
2002 1001W Published February 2003 Page 2 Plymouth, Minnesota 55441-4799
1-800-323-8295
DC Electrical Specifications @ + 25oC
Parameter Minimum Typical Maximum Units
Single VDD Supply Voltage 3.3* 5.0 5.5 V
VSS -5.0 V
Idd .07 10 uA
CMOS Logic Level (0) 0 0.8 V
CMOS Logic Level (1) VDD – 0.8 VDD V
Input Leakage Current 10 uA
* Performance curves are for Vdd = +5.0 +/- 10%
Absolute Maximum Ratings1
Parameter Absolute Maximum Units
VDD +6.0 V
VSS -5.5 V
Vin Digital Logic 0 - 0.6 V
Vin Digital Logic 1 Vdd + 0.6 V
Maximum Input Power > 35 dBm
ESD Voltage 400 V
Operating Temperature Range +85 Degrees C
Storage Temperature Range +125 Degrees C
(Note 1) Operation beyond any of these parameters may cause permanent damage.
Latch-Up: Unlike conventional CMOS RF switches, Honeywell's HRF-SW1001 is immune to latch-up.
ESD Protection: Although this device contains ESD protection circuitry on all digital inputs, conventional precautions should be
taken to ensure that the Absolute Maximum Ratings are not exceeded.
Package Outline Drawing
_________________________________________
3 mm
3 mm
Bottom View, 12 Pin 3X3 mm LPCC
TM
Package
ASAT LPCC Marketing Outline Dwg. # GMJ00004
For more information see http://www.asat.com
HRF-SW1001
________________________________________________________________________________________________________
Web Site: www.mysoiservices.com Honeywell
Email: mysoiservices@honeywell.com Solid State Electronics Center
Truth Table
Switch Control RF Output 1 RF Output 2
0
1
RF INPUT
- - -
- - -
RF INPUT
"0" = CMOS Low, "1” = CMOS High
Pin Configuration
Pin Function Pin Function
1 GROUND 7 GROUND
2 RF OUT 2 8 RF OUT 1
3 GROUND 9 GROUND
4 VDD 10 GROUND
5 SWITCH CONTROL 11 RF IN
6 VSS 12 GROUND
Note: Bottom ground plate must be grounded for proper RF performance.
Evaluation Circuit Board Connections
HRF-SW1001
Evaluation Board
Top View
Honeywell HRF-SW1001
Ground
VDD
SW
Control
VSS
Ground
RF Out2 RF Out1
RF In
12001 State Highway 55
2002 1001W Published February 2003 Page 3 Plymouth, Minnesota 55441-4799
1-800-323-8295
HRF-SW1001
________________________________________________________________________________________________________
Web Site: www.mysoiservices.com Honeywell
Email: mysoiservices@honeywell.com Solid State Electronics Center
Performance Curves
Insertion Loss
Insertion Loss Versus Frequency
-3.0
-2.5
-2.0
-1.5
-1.0
-0.5
0.0
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5
Frequency (GHz)
Insertion Loss (dB)
The Insertion Loss curve shows the
typical return loss versus frequency a
t
Vdd = +5.0 +/- 10%, Ta = 25C, Z0= 75
Ohms
Isolation
Isolation Versus Frequency
-100.0
-90.0
-80.0
-70.0
-60.0
-50.0
-40.0
-30.0
-20.0
0.0 0.5 1.0 1.5 2.0 2.5 3.0
Frequency [GHz]
Isolation [dB]
The Isolation curve shows the
typical isolation of an “off” state
output to the insertion path.
12001 State Highway 55
2002 1001W Published February 2003 Page 4 Plymouth, Minnesota 55441-4799
1-800-323-8295
HRF-SW1001
________________________________________________________________________________________________________
Web Site: www.mysoiservices.com Honeywell
Email: mysoiservices@honeywell.com Solid State Electronics Center
Return Loss
Input/Output Return Losses Versus Frequency
-40
-35
-30
-25
-20
-15
-10
-5
0
0 0.5 1 1.5 2 2.5 3
Frequency [GHz]
Return Loss [dB]
S11
The return loss curve shows
the input return loss S11 and
the output return loss in the
insertion path S22.
S22
Evaluation Circuit Board
HRF-SW1001 Evaluation Board
Honeywell's evaluation board provides
an easy to use method of evaluating the
RF performance of our switch. Simpl
y
connect power, DC and RF signals to
be measuring switch performance in
less than 10 minutes.
12001 State Highway 55
2002 1001W Published February 2003 Page 5 Plymouth, Minnesota 55441-4799
1-800-323-8295
HRF-SW1001
________________________________________________________________________________________________________
Web Site: www.mysoiservices.com Honeywell
Email: mysoiservices@honeywell.com Solid State Electronics Center
Evaluation Circuit Board Layout Design Details
Item Description
PCB Impedance Matched Multi-Layer FR4
Switch HRF-SW1001 RF Switch
Chip Capacitor Panasonic Model ECU-E1C103KBQ Capacitor, .01uf 0402 10% 16V
RF Connector Johnson Connectors Model 142-0701-801 SMA RF Coaxial Connector
DC Pin Mil-Max Model 800-10-064-10-001 Header Pins
Ordering Information
Ordering Number Product
HRF-SW1001-B
HRF-SW1001-TR
HRF-SW1001-E
Delivered In Chip Tubes
Delivered On Tape And Reel2
Engineering Evaluation Board
(Note 2) Contact Honeywell for details
LPCCTM is a registered Trademark of ASAT Ltd.
Honeywell reserves the right to make changes to improve reliability, function or design. Honeywell does not assume
any liability arising out of the application or use of any product or circuit described herein; neither does it convey any
license under its patent rights nor the rights of others.
12001 State Highway 55
2002 1001W Published February 2003 Page 6 Plymouth, Minnesota 55441-4799
1-800-323-8295
