Connector Termination Switch D3M Saves Wiring Effort, Production Steps, and Time Easy wiring ensured through the quick-connect terminals. External actuator mounts in either of two directions and increases Switch mounting flexibility. Horizontal layout of terminals saves mounting space. Same mounting pitch as the OMRON SS Subminiature Basic Switch. RCE Ordering Information Model Number Legend D3M-01jjj 1 1. 2 3 Actuator Mounting Position None: No actuator K: Pushbutton close to actuator fulcrum L: Note: 2. Actuator None: Pin plunger 1: Hinge lever 2: Hinge roller lever 3: Simulated hinge lever 3. Contact Form None: SPST-NC (with red pushbutton) -3: SPST-NO (with black pushbutton) Pushbutton far from actuator fulcrum For details about models with a low operating force, contact your OMRON sales representative. 1 D3M D3M List of Models Actuator Actuator mounting position Pin p plunger u ge --- Hinge ge lever e e K L Hinge g roller lever K L Simulated S u a ed hinge ge lever e e K L Specifications Ratings Rated voltage 30 VDC Resistive load 0.1 A Voltage (V) Use the D3M in the following permissible operating range. Operating range Inoperable range Current (mA) Minimum Applicable Load (Level N) Voltage 5 VDC Resistive load 1 mA Refer to Minute Load on page 18 for details. 2 Contact type Model SPST-NC D3M-01 SPST-NO D3M-01-3 SPST-NC D3M-01K1 SPST-NO D3M-01K1-3 SPST-NC D3M-01L1 SPST-NO D3M-01L1-3 SPST-NC D3M-01K2 SPST-NO D3M-01K2-3 SPST-NC D3M-01L2 SPST-NO D3M-01L2-3 SPST-NC D3M-01K3 SPST-NO D3M-01K3-3 SPST-NC D3M-01L3 SPST-NO D3M-01L3-3 D3M D3M Characteristics Permissible operating speed (see note 1) 0.1 mm/s to 1 m/s Permissible e ss b e ope operating a g frequency eque cy Mechanical: 400 operations/min max. Electrical: 60 operations/min max. Insulation resistance 100 M min. at 500 VDC Contact resistance (initial value) 100 m max. including connector and 50-mm AWG28 lead-wire resistance Dielectric strength e ec c s e g 1,000 VAC at 50/60 Hz for 1 min between terminals of the same polarity 1,500 VAC at 50/60 Hz for 1 min between charged metal part and ground 1,500 VAC at 50/60 Hz for 1 min between non-charged metal part and each terminal Vibration resistance (see note 2) Malfunction: 10 to 55 Hz, 1.5-mm double amplitude for 1 ms max. with contacts closed or open. Shock S oc resistance es s a ce (see note o e 2)) Destruction: 1,000 m/s2 {approx. 100G} max. Malfunction: 300 m/s2 {approx. 30G} for 1 ms max. with contacts closed or open. Life expectancy Mechanical: 500,000 operations (at full-stroke operating speed of 10 mm/s at a frequency of 60 operations/min) Electrical: 200,000 operations (at full-stroke operating speed of 10 mm/s at a frequency of 30 operations/min) Enclosure rating IP00 Degree of protection against electric shock Class I Proof tracking index (PTI) 175 Ambient temperature Operating: -25C to 85C (with no icing) Ambient humidity Operating: 85% max. (5C to 35C) Weight Approx. 2 g (pin plunger models) Note: 1. The permissible operating speed applies to pin plunger models. 2. If a lever actuator model is used, the above values apply for use at the total travel position. Approved Standards UL1054 (File No. E41515) CSA C22.2 No. 55 (File No. LR21642) TUV EN61058-1 (File No. R9750979) Rated voltage 30 VDC Rated current 0.1 A Contact Specifications Contact Crossbar Material Gold alloy Distance between contacts 0.5 mm Contact Form SPST-NC NC COM SPST-NO NO COM 3 D3M D3M Dimensions Note: 1. All units are in millimeters unless otherwise indicated. 2. Unless otherwise specified, a tolerance of 0.4 mm applies to all dimensions. Dimensions and Operating Characteristics Pin Plunger D3M-01 D3M-01-3 (See note 2) OF max. 1.50 N {153 gf} RF min. 0.25 N {25 gf} PT max. 0.6 mm OT min. 0.4 mm MD max. 0.1 mm OP 8.40.3 mm (See note 2) FP OP (See note 1) 2.35 +0.1 dia. -0.05 2.5 dia. Note: 1. The terminals connect to JST's Dipole XA Connector. 2. The Dipole XA Connector consists of the following components. Contact: SXA-001T-P0.6 Housing: XAP-02V-1 Hinge Lever D3M-01K1 D3M-01K1-3 Stainless steel (t = 0.3) (See note 2) OF max. 0.50 N {51 gf} RF min. 0.06 N {6 gf} OT min. 1.2 mm MD max. 0.8 mm FP max. 14.0 mm OP 10.00.8 mm (See note 2) FP OP (See note 1) 2.35 +0.1 dia. -0.05 2.5 dia. Note: 1. The terminals connect to JST's Dipole XA Connector. 2. The Dipole XA Connector consists of the following components. Contact: SXA-001T-P0.6 Housing: XAP-02V-1 D3M-01L1 D3M-01L1-3 Stainless steel (t = 0.3) (See note 2) OF max. 1.00 N {102 gf} RF min. 0.10 N {10 gf} OT min. 0.7 mm MD max. 0.6 mm FP max. 11.5 mm OP 9.20.6 mm (See note 2) FP OP (See note 1) 2.35 +0.1 dia. -0.05 4 2.5 dia. Note: 1. The terminals connect to JST's Dipole XA Connector. 2. The Dipole XA Connector consists of the following components. Contact: SXA-001T-P0.6 Housing: XAP-02V-1 D3M D3M Hinge Roller Lever D3M-01K2 D3M-01K2-3 Stainless steel (t = 0.3) (See note 2) 4.8 dia. x 3.2 polyacetal resin roller (See note 2) OP (See note 1) 2.35 +0.1 dia. -0.05 0.50 N {51 gf} RF min. 0.06 N {6 gf} OT min. 1.2 mm MD max. 0.8 mm FP max. 19.7 mm OP 15.70.8 mm FP 2.5 dia. Note: 1. The terminals connect to JST's Dipole XA Connector. 2. The Dipole XA Connector consists of the following components. Contact: SXA-001T-P0.6 Housing: XAP-02V-1 D3M-01L2 D3M-01L2-3 (See note 2) OF max. Stainless steel (t = 0.3) OF max. 1.00 N {102 gf} RF min. 0.10 N {10 gf} OT min. 0.7 mm MD max. 0.6 mm FP max. 17.2 mm OP 14.90.6 mm 4.8 dia. x 3.2 polyacetal resin roller (See note 2) (See note 1) 2.35 +0.1 dia. -0.05 OP 2.5 dia. Note: FP 1. The terminals connect to JST's Dipole XA Connector. 2. The Dipole XA Connector consists of the following components. Contact: SXA-001T-P0.6 Housing: XAP-02V-1 Simulated Hinge Lever D3M-01K3 D3M-01K3-3 (See note 2) Stainless steel (t = 0.3) OF max. 0.50 N {51 gf} RF min. 0.06 N {6 gf} OT min. 1.2 mm MD max. 0.8 mm FP max. 16.2 mm OP 12.20.8 mm (See note 2) OP (See note 1) 2.35 +0.1 dia. -0.05 2.5 dia. Note: FP 1. The terminals connect to JST's Dipole XA Connector. 2. The Dipole XA Connector consists of the following components. Contact: SXA-001T-P0.6 Housing: XAP-02V-1 5 D3M D3M D3M-01L3 D3M-01L3-3 Stainless steel (t = 0.3) (See note 2) OF max. 1.00 N {102 gf} RF min. 0.10 N {10 gf} OT min. 0.7 mm MD max. 0.6 mm FP max. 13.6 mm OP 11.30.6 mm (See note 2) OP (See note 1) 2.35 +0.1 dia. -0.05 2.5 dia. Note: FP 1. The terminals connect to JST's Dipole XA Connector. 2. The Dipole XA Connector consists of the following components. Contact: SXA-001T-P0.6 Housing: XAP-02V-1 Precautions Mounting Dimensions Use M2.3 screws, flat washers, and spring washers to mount the D3M securely. Make sure that the tightening torque applied to each screw is within a range from 0.23 to 0.26 N S m {2.3 to 2.7 kgf S cm}. Two, 2.4-dia. mounting hole or M2.3 screw hole Operating Stroke Make sure that the dog is separated from the actuator when the actuator is in the free position and that the actuator is pressed appropriately when the D3M is actuated. The actuator must not be pressed excessively to reach the maximum overtravel position, otherwise the D3M may be damaged. Make sure the actuator is pressed in the direction where the D3M is actuated. Correct Use Refer to pages 22 to 29 for common precautions. Wiring Connectors The terminals connect to JST's Dipole XA Connector. The Dipole XA Connector consists of the following components. Contact: SXA-001T-P0.6 Housing: XAP-02V-1 OMRON does not sell the Dipole XA Connector. Contact the following. J.S.T. Manufacturing Co., Ltd. (Japan) Tel: (81)45-543-1271 Fax: (81)45-544-1503 J.S.T. (U.K.) Ltd. (United Kingdom) Tel: (44)1986-874131 Fax: (44)1986-874276 J.S.T. Corporation (U.S.A.) Tel: (1)847-473-1957 Fax: (1)847-473-0144 J.S.T. (H.K.) Co. Ltd. (Hong Kong) Tel: (852)24137979 Fax: (852)24111193 ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. Cat. No. B100-E1-2 6