Technical Data July 2015 3MTM Thermally Conductive Adhesive Transfer Tapes 8805 * 8810 * 8815 * 8820 Product Description 3MTM Thermally Conductive Adhesive Transfer Tapes 8805, 8810, 8815 and 8820 are designed to provide a preferential heat-transfer path between heat-generating components and heat sinks or other cooling devices (e.g., fans, heat spreaders or heat pipes). Features and Benefits * High mechanical strength * Improved surface wet-out for rough surface/LSE substrates * Excellent shock performance * Wider and longer roll is available * Halogen free* * Ideal for thin bonding applications * Good thermal transfer Product Construction Product Number 3MTM Thermally Conductive Adhesive Transfer Tapes 8810 8815 8805 Color White Tape Type Tape Thickness Filled Acrylic Polymer 0.125 mm (5 mils) Filler Type Liner Type Liner Thickness 8820 0.25 mm (10 mils) 0.375 mm (15 mils) 0.50 mm (20 mils) Ceramic Dual liner using silicone-treated polyester. Easy release PET liner is clear in color, tight side PET liner is blue in color 37.5-50 m (1.5~2 mils) thickness for inside or outside wound liner. * Halogen Free is defined as having maximum 900 ppm bromine, maximum 900 ppm chlorine, and/or maximum 1500 ppm total bromine and chlorine, per IEC 61249-2-21. 3MTM Thermally Conductive Adhesive Transfer Tapes 8805 * 8810 * 8815 * 8820 Typical Physical Properties and Performance Characteristics Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Product Number 3MTM Thermally Conductive Adhesive Transfer Tapes 8805 8810 8815 8820 Property Value Thermal Impedance (C cm2/W) (C in2/W) 3.2 (0.5) Method 5.8 (0.9) 7.7 (1.2) Thermal Conductivity (W/m-K) 9.7 (1.5) 0.60 Specific Gravity 3M test method ASTM C-177 1.07 g/cc Surface Resistivity (-cm) 1.6 x 1011 1.6 x 1011 1.5 x 1011 **1.5 x 1011 ASTM D-2577 Volume Resistivity (-cm) 5.2 x 1011 3.9 x 1011 3.8 x 1011 **3.8 x 1011 ASTM D-2577 ** ** ASTM D-149 Dielectric Strength (kV/mm) (V/mil) Dielectric Properties (frequency) 26 (688) 3 MHz 100 MHz 1 GHz ** ASTM D-150 93.5 3.2 3.0 ** ASTM D-150 8805 8810 8815 8820 Room Temp Dwell @ 15 min 990 (35) 1300 (46) 1500 (53) 1700 (60) 65C Dwell @ 15 min 1450 (51) 2040 (72) 2440 (86) 2780 (98) Room Temp Dwell @ 72 hrs 1500 (53) 2130 (75) 2520 (89) 3060 (108) 65C Temp Dwell @ 72 hrs 1590 (56) 2500 (88) 4000 (141) 4130 (181) Dielectric Constant (8815) 90 Degree Peel Test grams/25.4 mm width (oz/in) Untreated aluminum substrate 3M test method 1 mil PET Backing Static Shear test of holding PASS PASS PASS PASS 1000g @ Room Temp using 1 in2 3M test method: SS & PET Hold weight 1 week Static Shear test of holding PASS PASS PASS PASS 500g @ 70C using 1 in2 3M test method: SS & PET Hold weight 1 week Heat Aging and Environmental Cycling Performance Products pass UL-746C Heat Aging testing* and Environmental Cycling testing. Contact your 3M technical services representative for details. * UL-746A file number E213134 ** Estimated value based on Tape 8815 test data *** When ASTM is mentioned, the test was performed in accordance with the ASTM test method (2) TBD UL-746C 3MTM Thermally Conductive Adhesive Transfer Tapes 8805 * 8810 * 8815 * 8820 Typical Physical Properties and Performance Characteristics (continued) Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Overlap Shear at Specific Temperatures Properties: (Test conditions: Test substrates are bare untreated aluminum or anodized aluminum, 1 in.2 test sample size, shear speed = 0.5 inch/minute. Samples heated to temperature noted below in 5 minutes and then OLS tested. Before testing, samples are dwelled for 3 days at RT to build adhesive bond to substrate). 3MTM Thermally Conductive Adhesive Transfer Tapes 250 Overlap Shear (psi) 200 88XX is cohesively (split) from anodized aluminum surface 88XX is cleanly sheared from bare aluminum surface 150 RT 50C 70C 100 50 0 Tape 8805 Tape 8810 Tape 8805 on AA Tape 8815 Tape 8810 on AA Tape 8815 on AA Overlap Shear Heat Aged Properties: (Test conditions: Test substrates are bare untreated aluminum, OLS speed is 0.5 in./min., adhesive cleanly removes from substrate surface during OLS test, 1 in.2 test sample size, test at RT conditions after aging cycle complete, 3M Tape 8810). 3MTM Thermally Conductive Adhesive Transfer Tapes 250 150C 120C Overlap Shear (psi) 200 150 100 50 0 Initial 1 week 2 weeks 3 weeks 4 weeks Time at Temperature Before Testing (3) 5 weeks 6 weeks 3MTM Thermally Conductive Adhesive Transfer Tapes 8805 * 8810 * 8815 * 8820 Typical Physical Properties and Performance Characteristics (continued) Note: The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Torque Resistance: (Test conditions: This test indicates the resistance to twisting shear forces, heat sink attachment to different chip package material types, 1.0 hour room temperature dwell after attachment to the package surface before torque testing is completed). 3MTM Thermally Conductive Adhesive Transfer Tapes 70 60 PBGA PLCC Steel Torque (inch - lbs.) 50 40 30 20 10 0 Tape 8805 Tape 8815 Tape 8810 Thermal Impedance (C-in2/W) vs. Thickness: (Test Conditions: 3M test method). 3MTM Thermally Conductive Adhesive Transfer Tapes 1.6 1.5 1.4 Impedance (C-in2/W) 1.2 Slope 1/k k = 0.6 W/m-K 1 0.9 0.8 0.6 0.5 0.4 0.2 0 0 5 15 10 Thickness (mils) (4) 20 25 3MTM Thermally Conductive Adhesive Transfer Tapes 8805 * 8810 * 8815 * 8820 Available Sizes Width: Maximum width 22 inches. Length: Multiples of 36 yds. Maximum 108 yds. Custom Sizes: Contact your local 3M sales representative for information and availability of custom sizes (width and length) or die cut parts of 3MTM Thermally Conductive Adhesive Transfer Tapes 8805, 8810, 8815 and 8820. Application Guidelines 1)Substrate surfaces should be clean and dry prior to tape application. Isopropyl alcohol (isopropanol) applied with a lint-free wipe or swab should be adequate for removing surface contamination such as dust or finger prints. Do not use "denatured alcohol" or glass cleaners which often contain oily components. Allow the surface to dry for several minutes before applying the tape. More aggressive solvents (such as acetone, methyl ethyl ketone (MEK) or toluene) may be required to remove heavier contamination (grease, machine oils, solder flux, etc.) but should be followed by a final isopropanol wipe as described above. Note:Be sure to read and follow the manufacturers' precautions and directions when using primers and solvents. 2)Apply the tape to one substrate at a modest angle with the use of a squeegee, rubber roller or finger pressure to help reduce the potential for air entrapment under the tape during its application. The liner can be removed after positioning the tape onto the first substrate. 3)Assemble the part by applying compression to the substrates to ensure a good wetting of the substrate surfaces with the tape. Proper application of pressure (amount of pressure, time applied, temperature applied) will depend upon design of the parts. Rigid substrates are more difficult to bond without air entrapment as most rigid parts are not flat. Use of a thicker tape may result in increased wetting of rigid substrates. Flexible substrates can be bonded to rigid or flexible parts with much less concern about air entrapment because one of the flexible substrates can conform to the other substrate. 4)Application pressure guideline table for 3MTM Thermally Conductive Adhesive Transfer Tapes 8805, 8810, 8815 and 8820. Substrate Application Conditions Time Rigid to rigid Minimum: 15 psi at room temperature Preferred: 50 psi at room temperature More pressure equals better wetting 2 sec 5 sec Flexible to rigid Minimum: 5 psi at room temperature Preferred: 15 psi at room temperature 1 sec 5 sec Flexible to flexible Minimum: 5 psi at room temperature Preferred: 15 psi at room temperature 1 sec 5 sec (5) 3MTM Thermally Conductive Adhesive Transfer Tapes 8805 * 8810 * 8815 * 8820 Application Guidelines (continued) 5) Application Tips: *For rigid to rigid bonding, a twisting motion during assembly of the substrates will improve wetting. This should be a back and forth twisting motion during the application of compression. *For flexible to rigid or flexible to flexible bonding, a roll lamination system may be employed to apply the flexible substrate down to the rigid (or other flexible) substrate. Rubber nip rollers, heated steel rollers, and other methods can be employed to bond in a continuous manner. *Heat can be employed to increase wetting percentage and wetting rate of the substrates and to build room temperature bond strength. *Primers may be employed to increase adhesion to low surface energy substrates (eg. plastic packages). Contact your 3M Technical Service Representative for more information about primers. *For best product performance, it is important to use pressure and time conditions to achieve as much wetting as possible. 6) Rework Tips: *Rework requires separation of the two substrates. Separation can be accomplished by any practical means: prying, torquing or peeling. The tape will be destroyed upon separation and must be replaced. The surfaces should be re-cleaned according to the recommendations in this data page. * Heating up the substrates can reduce the adhesion level and make removal easier. *Part separation can be aided by immersion in warm water. This should eventually reduce the adhesion and make prying, torquing or peeling apart the substrates easier. Application Ideas *3MTM Thermally Conductive Adhesive Transfer Tapes 8805, 8810, 8815 and 8820 are designed to provide a preferential heat-transfer path between heat-generating devices and cooling devices (e.g., fans, heat pipes and heat sinks). Shelf Life The shelf life of 3MTM Thermally Conductive Adhesive Transfer Tapes 8805, 8810, 8815 and 8820 is 24 months from the date of manufacture when stored in the original packaging materials and stored at 22C (72F) and 50% relative humidity. (6) 3MTM Thermally Conductive Adhesive Transfer Tapes 8805 * 8810 * 8815 * 8820 Regulatory For regulatory information about this product, contact your 3M representative. Technical Information The technical information, recommendations and other statements contained in this document are based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed. Product Use Many factors beyond 3M's control and uniquely within user's knowledge and control can affect the use and performance of a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user's method of application. Warranty, Limited Remedy, and Disclaimer Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M's option, replacement of the 3M product or refund of the purchase price. Limitation of Liability Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. Electronics Materials Solutions Division 3M Center, Building 224-3N-11 St. Paul, MN 55144-1000 1-800-251-8634 phone 651-778-4244 fax www.3M.com/electronics 3M is a trademark of 3M Company. Please recycle. (c) 3M 2015. All rights reserved. 78-6900-9998-7 (7)