MAXQ3180-RAN+ - Maxim - Product.Network

General Description

The MAXQ3180 is a dedicated electricity measurement

front-end that collects and calculates polyphase volt-

age, current, power, energy, and many other metering

and power-quality parameters of a polyphase load. The

computed results can be retrieved by an external mas-

ter through the on-chip serial peripheral interface

(SPI™) bus. This bus is also used by the external mas-

ter to configure the operation of the MAXQ3180 and

monitor the status of operations.

The MAXQ3180 performs voltage and current measure-

ments using an integrated ADC that can measure up to

seven external differential signal pairs. An eighth differ-

ential signal pair is used to measure the die tempera-

ture. An internal amplifier automatically adjusts the

current channel gain to compensate for low-current

channel-signal levels.

Applications

3-Phase Multifunction Electricity Meters

Features

♦Compatible with 3-Phase/3-Wire, 3-Phase/4-Wire,

and Other 3-Phase Services

♦Active Power and Energy of Each Phase and

Combined 3-Phase (kWh), Positive and Negative

♦Reactive Power and Energy of Each Phase and

Combined, Positive and Negative

♦Apparent Power and Energy of Each Phase and

Combined 3-Phase

♦Neutral Line Current Measurement

♦Line Frequency (Hz)

♦Power Factors

♦Voltage Phasor Angles

♦Phase Sequence Indication

♦Phase Voltage Absence Detection

♦Voltage and Current Harmonic Measurement

♦Fundamental and Total Power and Energy

♦Two Pulse Outputs: Configurable for Active,

Reactive, and Apparent Powers

♦Programmable Pulse Widths

♦Programmable No-Load Current Threshold

♦Programmable Meter Constants

♦Programmable Thresholds for Undervoltage and

Overvoltage Detection

♦Programmable Threshold for Overcurrent Detection

♦Amp-Hours in Absence of Voltage Signals

♦On-Chip Digital Temperature Sensor

♦Precision Internal Voltage Reference 2.048V

(30ppm/°C typical), Also Supports An External

Voltage Reference

♦Supports Software Meter Calibration

♦Up to 3-Point Multipoint Calibration to

Compensate for Transducer Nonlinearity

♦Power-Fail Detection

♦Bidirectional Reset Input/Output

♦SPI-Compatible Serial Interface with Interrupt

Request (IRQ) Output

♦Single 3.3V Supply, Low Power (35mW typical)

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

________________________________________________________________

Maxim Integrated Products

19-4674; Rev 3; 12/09

For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,

or visit Maxim’s website at www.maxim-ic.com.

Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device may be

simultaneously available through various sales channels. For information about device errata, go to: www.maxim-ic.com/errata.

MAXQ is a registered trademark of Maxim Integrated Products, Inc.

SPI is a trademark of Motorola, Inc.

Ordering Information

Denotes a lead(Pb)-free/RoHS-compliant package.

PART TEMP RANGE PIN-PACKAGE

MAXQ3180-RAN+ -40°C to +85°C 28 TSSOP

Pin Configuration and Typical Application Circuit appear at

end of data sheet.

MAXQ3180
Low-Power, Multifunction, Polyphase AFE
2 _______________________________________________________________________________________
Absolute Maximum Ratings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Metering Specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Electrical Characteristics  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
SPI Slave Mode Timing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Block Diagram  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Pin Description  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Detailed Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Analog Front-End  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Digital Signal Processor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Precision Pulse Generators  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
SPI Peripheral  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Operating Modes  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Run Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Stop Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Reset Sources  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
External Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Power-On Reset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Watchdog Reset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Software Reset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Power-Supply Monitoring  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Clock Sources  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
External High-Frequency Crystal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
External High-Frequency Clock  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Internal RC Oscillator  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Master Communications  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
SPI Communications Rate and Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
SPI Communications Protocol  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Host Software Design  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Register Set  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
RAM-Based Registers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
General Operating Registers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Global Status Register (STATUS) (0x000)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Operating Mode Register 0 (OPMODE0) (0x001)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Operating Mode Register 1 (OPMODE1) (0x002)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Operating Mode Register 2 (OPMODE2) (0x003)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
TABLE OF CONTENTS

MAXQ3180
Low-Power, Multifunction, Polyphase AFE
_______________________________________________________________________________________ 3
Global Interrupt Registers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Interrupt Request Flag Register (IRQ_FLAG) (0x004)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Interrupt Mask Register (IRQ_MASK) (0x006)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Meter Pulse Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Pulse Configuration—CFP Output (PLSCFG1) (0x01E)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Pulse Configuration—CFQ Output (PLSCFG2) (0x01F)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
CFP Pulse Width (PLS1_WD) (0x020)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
CFP Pulse Threshold (THR1) (0x022)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
CFQ Pulse Width (PLS2_WD) (0x026) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
CFQ Pulse Threshold (THR2) (0x028) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Calibration Registers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Current Gain, Phase X = A/B/C/N (X.I_GAIN) (A: 0x130, B: 0x21C, C: 0x308, N: 0x12E)  . . . . . . . . . . . . . . . . . . .38
Voltage Gain, Phase X = A/B/C (X.V_GAIN) (A: 0x132, B: 0x21E, C: 0x30A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Energy Gain, Phase X = A/B/C (X.E_GAIN) (A: 0x134, B: 0x220, C: 0x30C)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Phase-Angle Compensation, High Range, Phase X = A/B/C (X.PA0) (A: 0x13E, B: 0x22A, C: 0x316)  . . . . . . . . .39
Phase-Angle Compensation, Medium Range, Phase X = A/B/C (X.PA1) (A: 0x140, B: 0x22C, C: 0x318)  . . . . . .40
Phase-Angle Compensation, Low Range, Phase X = A/B/C (X.PA2) (A: 0x142, B: 0x22E, C: 0x31A)  . . . . . . . . .40
Limit Registers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Overcurrent Level (OCLVL) (0x044)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Overvoltage Level (OVLVL) (0x046)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Undervoltage Level (UVLVL) (0x048)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
No-Load Level (NOLOAD) (0x04A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Phase Status Registers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Interrupt Flags, Phase X = A/B/C (X.FLAGS) (A: 0x144, B: 0x230, C: 0x31C)  . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Interrupt Mask, Phase X = A/B/C (X.MASK) (A: 0x145, B: 0x231, C: 0x31D)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Energy Overflow Flags, Phase X = A/B/C (X.EOVER) (A: 0x146, B: 0x232, C: 0x31E)  . . . . . . . . . . . . . . . . . . . . .43
Measurements  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Line Frequency (LINEFR) (0x062) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Power Factor, Phase X = A/B/C (X.PF) (A: 0x1C6, B: 0x2B2, C: 0x39E)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
RMS Voltage, Phase X = A/B/C (X.VRMS) (A: 0x1C8, B: 0x2B4, C: 0x3A0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
RMS Current, Phase X = A/B/C (X.IRMS) (A: 0x1CC, B: 0x2B8, C: 0x3A4)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Energy, Real Positive, Phase X = A/B/C (X.EAPOS) (A: 0x1E8, B: 0x2D4, C: 0x3C0)  . . . . . . . . . . . . . . . . . . . . . .45
Energy, Real Negative, Phase X = A/B/C (X.EANEG) (A: 0x1EC, B: 0x2D8, C: 0x3C4) . . . . . . . . . . . . . . . . . . . . .46
Energy, Reactive Positive, Phase X = A/B/C (X.ERPOS) (A: 0x1F0, B: 0x2DC, C: 0x3C8)  . . . . . . . . . . . . . . . . . .46
Energy, Reactive Negative, Phase X = A/B/C (X.ERNEG) (A: 0x1F4, B: 0x2E0, C: 0x3CC)  . . . . . . . . . . . . . . . . .47
Energy, Apparent, Phase X = A/B/C (X.ES) (A: 0x1F8, B: 0x2E4, C: 0x3D0)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
TABLE OF CONTENTS (continued)

MAXQ3180
Low-Power, Multifunction, Polyphase AFE
4 _______________________________________________________________________________________
Virtual Register Conversion Coefficients  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Voltage Units Conversion Coefficient (VOLT_CC) (0x014)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Current Units Conversion Coefficient (AMP_CC) (0x016) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Power Units Conversion Coefficient (PWR_CC) (0x018) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Energy Units Conversion Coefficient (ENR_CC) (0x01A)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Virtual Registers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Real Power, Phase X = A/B/C/T (PWRP.X) (A: 0x801, B: 0x802, C: 0x804, T: 0x807)  . . . . . . . . . . . . . . . . . . .51
Reactive Power, Phase X = A/B/C/T (PWRQ.X) (A: 0x811, B: 0x812, C: 0x814, T: 0x817)  . . . . . . . . . . . . . . .52
Apparent Power, Phase X = A/B/C/T (PWRS.X) (A: 0x821, B: 0x822, C: 0x824, T: 0x827)  . . . . . . . . . . . . . . .52
Voltage and Current   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
RMS Volts, Phase X = A/B/C (V.X) (A: 0x831, B: 0x832, C: 0x834)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
RMS Amps, Phase X = A/B/C/N (I.X) (A: 0x841, B: 0x842, C: 0x844, N: 0x840)  . . . . . . . . . . . . . . . . . . . . . . .53
Power Factor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Power Factor (PF.T) (0x867)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Energy   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Real Energy, Phase A/B/C/T (ENRP.X) (A: 0x8C1, B: 0x8C2, C: 0x8C4, T: 0x8C7) . . . . . . . . . . . . . . . . . . . . .54
Reactive Energy, Phase A/B/C/T (ENRQ.X) (A: 0x8D1, B: 0x8D2, C: 0x8D4, T: 0x8D7)  . . . . . . . . . . . . . . . . .54
Apparent Energy, Phase A/B/C/T (ENRS.X) (A: 0x871, B: 0x872, C: 0x874, T: 0x877)  . . . . . . . . . . . . . . . . . .54
Theory of Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Analog Front-End Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Digital Signal Processing (DSP) Terminology  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Digital Processing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Per Sample Operations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Per DSP Cycle Operations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Energy Accumulation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
No-Zero-Crossing Detection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Phase Sequence Status  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
RMS Voltage, RMS Current, and Energy Calculation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Power Calculation (Active, Reactive, Apparent)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Energy Accumulation Start Delay  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
No-Load Feature  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
On Demand Calculations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
RMS Volts, RMS Amps  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Power  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Power Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
TABLE OF CONTENTS (continued)

MAXQ3180
Low-Power, Multifunction, Polyphase AFE
_______________________________________________________________________________________ 5
Line Frequency   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Phasor Angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Meter Pulse  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Generating Pulses  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Meter Constant  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Overvoltage and Overcurrent Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Meter Units to Real Units Conversion  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Units Conversion Examples  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Calibration Procedure  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Calibration Overview  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Calibrating Voltage  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Calibrating Current  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Calibrating Phase Offset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Interfacing the MAXQ3180 to External Hardware  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Connections to the Power Source  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Sensor Selection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Voltage Sensors  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Voltage-Divider  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Voltage Transformer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Current Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Current Shunt  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Current Transformer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Advanced Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Modifying the ADC Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Fine-Tuning the DSP Controls  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Fine-Tuning the Line Frequency Measurement  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Fundamental Mode Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Harmonic Measurement  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Low-Power Measurement Mode (LOWPM)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Temperature  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Advanced Calibrations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Calibrating Current Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Calibrating Linearity  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Calibrating Power/Energy Gain  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Multipoint Phase Offset Calibration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
TABLE OF CONTENTS (continued)

MAXQ3180
Low-Power, Multifunction, Polyphase AFE
6 _______________________________________________________________________________________
Advanced Register Configurations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Analog Scan Configuration Registers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Time Slot Assignment—Current Channel X = A/B/C (SCAN_IX) (A: 0x008, B: 0x00C, C: 0x00A) . . . . . . . . . .73
Time Slot Assignment—Voltage Channel X = A/B/C (SCAN_VX) (A: 0x009, B: 0x00D, C: 0x00B)  . . . . . . . . .74
Time Slot Assignment—Neutral Current Channel (SCAN_IN) (0x00E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Time Slot Assignment—Temperature Channel (SCAN_TE) (0x00F)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Neutral Current and Harmonics  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Auxiliary Channel Configuration (AUX_CFG) (0x010)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
DSP System Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
System Clock Frequency (SYS_KHZ) (0x012)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Cycle Count (CYCNT) (0x01C)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Number of Scan Frames per DSP Cycle (NS) (0x040) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Filter Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Line Cycle Noise Rejection Filter (REJ_NS) (0x02C)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Line Cycle Averaging Filter (AVG_NS) (0x02E)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Meter Measurement Averaging Filter (AVG_C) (0x030)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Meter Measurement Highpass Filter (HPF_C) (0x032) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Fundamental Filter Feed-Forward Coefficient (B0FUND) (0x034)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Fundamental Filter Feedback Coefficient (A1FUND) (0x036)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Harmonic Filter Feed-Forward Coefficient (B0HARM) (0x03A)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Harmonic Filter Feedback Coefficient (A1HARM) (0x03C)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Zero-Cross Lowpass Filter (ZC_LPF) (0x05A)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Hardware Mirror Registers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
ADC Configuration (R_ACFG) (0x04C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
ADC Conversion Rate (R_ADCRATE) (0x04E)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
ADC Settling Time (R_ADCACQ) (0x050)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
SPI Configuration (R_SPICF) (0x052)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Timeouts  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Zero-Crossing Timeout (NZX_TIMO) (0x054)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Communications Timeout (COM_TIMO) (0x056)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Energy Accumulation Timeout (ACC_TIMO) (0x058)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Phase-Angle Compensation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Phase Offset Current Threshold 1 (I1THR) (0x05C)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Phase Offset Current Threshold 2 (I2THR) (0x05E)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Miscellaneous Gain  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Neutral Current Gain (N.I_GAIN) (0x12E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Gain, Fundamental Energy, Phase X = A/B/C (X.EF_GAIN) (A: 0x136, B: 0x222, C: 0x30E)  . . . . . . . . . . . . .87
TABLE OF CONTENTS (continued)

MAXQ3180
Low-Power, Multifunction, Polyphase AFE
_______________________________________________________________________________________ 7
Linearity Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Linearity Offset, High Range, Phase X = A/B/C (X.OFFS_HI) (A: 0x138, B: 0x224, C: 0x310) . . . . . . . . . . . . .87
Linearity Gain Coefficient, Low Range, Phase X = A/B/C (X.GAIN_LO) (A: 0x13A, B: 0x226, C: 0x312)  . . . .87
Linearity Offset, Low Range, Phase X = A/B/C (X.OFFS_LO) (A: 0x13C, B: 0x228, C: 0x314)  . . . . . . . . . . . .88
Measurements—RAM Registers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
On-Demand RMS Result (N.IRMS) (0x11C)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Fundamental Energy  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Fundamental Energy Overflow Flags, Phase X = A/B/C (X.EFOVER) (A: 0x147, B: 0x233, C: 0x31F)  . . . . . .89
Energy, Fundamental, Real Positive, Phase X = A/B/C (X.EAFPOS) (A: 0x1FC, B: 0x2E8, C: 0x3D4)  . . . . . .89
Energy, Fundamental, Real Negative, Phase X = A/B/C (X.EAFNEG) (A: 0x200, B: 0x2EC, C: 0x3D8)  . . . . .90
Energy, Fundamental, Reactive Positive, Phase X = A/B/C (X.ERFPOS) (A: 0x204, B: 0x2F0, C: 0x3DC)  . . .90
Energy, Fundamental, Reactive Negative, Phase X = A/B/C (X.ERFNEG) (A: 0x208, B: 0x2F4, C: 0x3E0)  . .91
Energy Fundamental, Apparent, Phase X = A/B/C (X.ESF) (A: 0x20C, B: 0x2F8, C: 0x3E4) . . . . . . . . . . . . . .91
Energy Accumulated in the Last DSP Cycle  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Real Energy, Phase X = A/B/C (X.ACT) (A: 0x1D0, B: 0x2BC, C: 0x3A8)  . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Reactive Energy, Phase X = A/B/C (X.REA) (A: 0x1D4, B: 0x2C0, C: 0x3AC) . . . . . . . . . . . . . . . . . . . . . . . . .92
Apparent Energy, Phase X = A/B/C (X.APP) (A: 0x1D8, B: 0x2C4, C: 0x3B0) . . . . . . . . . . . . . . . . . . . . . . . . .93
Fundamental Energy Accumulated in the Last DSP Cycle  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Fundamental Real Energy, Phase X = A/B/C (X.ACTF) (A: 0x1DC, B: 0x2C8, C: 0x3B4)  . . . . . . . . . . . . . . . .93
Fundamental Reactive Energy, Phase X = A/B/C (X.REAF) (A: 0x1E0, B: 0x2CC, C: 0x3B8)  . . . . . . . . . . . . .94
Fundamental Apparent Energy, Phase X = A/B/C (X.APPF) (A: 0x1E4, B: 0x2D0, C: 0x3BC)  . . . . . . . . . . . .94
Checksum (CHKSUM) (0x060)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
Measurements—Virtual Registers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Fundamental Real Power, Phase A/B/C/T (PWRPF.X) (A: 0x881, B: 0x882, C: 0x884, T: 0x887)  . . . . . . . . . . . . .96
Fundamental Reactive Power, Phase A/B/C/T (PWRQF.X) (A: 0x891, B: 0x892, C: 0x894, T: 0x897)  . . . . . . . . . .96
Fundamental Apparent Power, Phase A/B/C/T (PWRSF.X) (A: 0x8A1, B: 0x8A2, C: 0x8A4, T: 0x8A7)  . . . . . . . . .97
Fundamental Real Energy, Phase A/B/C/T (ENRPF.X) (A: 0x8E1, B: 0x8E2, C: 0x8E4, T: 0x8E7) . . . . . . . . . . . . .97
Fundamental Reactive Energy, Phase A/B/C/T (ENRQF.X) (A: 0x8F1, B: 0x8F2, C: 0x8F4, T: 0x8F7)  . . . . . . . . .97
Fundamental Apparent Energy, Phase A/B/C/T (ENRSF.X) (A: 0x8B1, B: 0x8B2, C: 0x8B4, T: 0x8B7)  . . . . . . . .97
Phasors  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Phase B Phasor (VBPH: 0x852)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Phase C Phasor (VCPH: 0x854)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Harmonics  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
RMS Voltage, Harmonic (V.HARM) (0x830)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
RMS Current, Harmonic/Neutral (I.N, I.HARM) (0x840)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Ratio of Harmonic/Fundamental (HARM_NF) (0x850)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
TABLE OF CONTENTS (continued)

MAXQ3180
Low-Power, Multifunction, Polyphase AFE
8 _______________________________________________________________________________________
Special Commands  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Applications Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Grounds and Bypassing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Specific Design Considerations for MAXQ3180-Based Systems  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Additional Documentation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Technical Support  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Pin Configuration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Package Information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Typical Application Circuit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
Revision History  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
TABLE OF CONTENTS (continued)

MAXQ3180
Low-Power, Multifunction, Polyphase AFE
_______________________________________________________________________________________ 9
Figure 1. External Reset  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Figure 2. Brownout Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Figure 3. Simplified Clock Sources  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Figure 4a. SPI Interface Timing (CKPHA = 0)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Figure 4b. SPI Interface Timing (CKPHA = 1)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Figure 5. Read SPI Transfer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Figure 6. Write SPI Transfer  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Figure 7. Flowchart for Reading from MAXQ3180  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Figure 8. Flowchart for Writing to MAXQ3180  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Figure 9. Per Sample Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Figure 10. Computation of RMS Values  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Figure 11. Phase Compensation for Energy Calculations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Figure 12. Apparent and Reactive Energy Calculations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Figure 13. Sample Voltage Input Circuit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Figure 14. Sample Current Input Circuit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Figure 15. Offset Testing Setup  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Figure 16. Phase Offset vs. Input Current Calibration  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Table 1. Command Format for SPI Register Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Table 2. Command Format for SPI Register Write  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Table 3. RAM Register Map  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Table 4. Virtual Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Table 5. Meter Unit Definitions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Table 6. Virtual Register Coefficients  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Table 7. Virtual Registers That Activate Special Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
LIST OF FIGURES
LIST OF TABLES

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

10 ______________________________________________________________________________________

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

Voltage Range on DVDD Relative to DGND .........-0.3V to +4.0V

Voltage Range on AVDD Relative to AGND..........-0.3V to +4.0V

Voltage Range on AGND Relative to DGND .........-0.3V to +0.3V

Voltage Range on AVDD Relative to DVDD ..........-0.3V to +0.3V

Voltage Range on Any Pin Relative to

DGND except VxP, IxN Pins..............................-0.3V to +4.0V

Voltage Range on VxP, IxN Relative to AGND ......-0.3V to +4.0V

Operating Temperature Range ...........................-40°C to +85°C

Junction Temperature......................................................+150°C

Storage Temperature Range .............................-65°C to +150°C

Lead Soldering Temperature .............................Refer to the IPC/

JEDEC J-STD-020 Specification.

PARAMETER CONDITIONS MIN TYP MAX UNITS

Active Energy Linearity Error DR 1000:1 0.1 %

Reactive Energy Linearity Error DR 1000:1 0.2 %

Apparent Energy Linearity Error DR 1000:1 0.5 %

RMS Voltage Linearity Error DR 20:1 0.5 %

DR 500:1 1.0

RMS Current Linearity Error DR 20:1 0.5 %

Line Frequency Error 0.5 %

Power Factor Error 1.0 %

ELECTRICAL CHARACTERISTICS

(VAVDD = VDVDD = VRST to 3.6V, TA= -40°C to +85°C, unless otherwise noted.) (Note 2)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

POWER-SUPPLY SPECIFICATIONS

Digital Supply Voltage VDVDD V

RST 3.6 V

Power-Fail Interrupt Trip Point VPFW Active mode, EPWRF = 1 2.84 3.13 V

Power-Fail Reset Trip Point VRST Active mode 2.70 2.99 V

Analog Supply Voltage VAVDD V

RST 3.6 V

Analog Supply Current IAVDD f

CLK = 8MHz 0.9 1.8 mA

Digital Supply Current IDVDD f

CLK = 8MHz 8.5 13 mA

Low-Power Measurement Mode

Current ILOWPM LOWPM = 1 (Note 1) 4.2 mA

Stop-Mode Current 0.2 12 μA

DIGITAL I/O SPECIFICATIONS

Input High Voltage VIH 0.7 x

VDVDD V

Input Low Voltage VIL 0.3 x

VDVDD V

Input Hysteresis VIHYS V

DVDD = 3.3V 500 mV

Input Leakage IL V

IN = DGND or VDVDD, pullup off ±0.01 ±1 μA

METERING SPECIFICATIONS

(VAVDD = VDVDD = VRST to 3.6V, Current Channel Dynamic Range 1000:1 at TA= +25°C, unless otherwise noted.) (Note 1)

ABSOLUTE MAXIMUM RATINGS

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 11

ELECTRICAL CHARACTERISTICS (continued)

(VAVDD = VDVDD = VRST to 3.6V, TA= -40°C to +85°C, unless otherwise noted.) (Note 2)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Input Low Current IIL V

IN = 0.4V, weak pullup on -50 μA

RESET Pullup Resistance RRESET 50 150 200 k

IOH = -4mA VDVDD

- 0.4

Output High Voltage (Except

RESET)VOH

IOH = -6mA VDVDD

- 0.5

IOL = 4mA 0.4

Output Low Voltage VOL IOL = 6mA 0.5 V

SYSTEM CLOCK SOURCES

External Clock Input Frequency 0 8.12 MHz

External Clock Input Duty Cycle 45 55 %

External HF Crystal Frequency fSYS Fundamental mode 8.12 MHz

XTAL1, XTAL2 Internal Load

Capacitance 16 pF

Internal RC Oscillator Frequency 7.4 7.6 8.6 MHz

Internal RC Oscillator Accuracy ±2 %

Internal RC Oscillator Current 50 120 μA

Internal RC Oscillator Startup

Delay (Note 1) 0.45 μs

ANALOG-TO-DIGITAL CONVERTER

Input Voltage Range 0 VREF V

Common-Mode Bias VCOMM 1.14 V

Offset Error ±2 mV

Offset Error Drift ±8 μV/°C

Gain Error (G = 1) 0.05 %

Spurious-Free Dynamic Range SFDR 90 dB

Total Harmonic Distortion THD 90 dB

Input Bandwidth (-3dB) (Note 1) 7 kHz

INTERNAL VOLTAGE REFERENCE

Temperature Coefficient (Note 1) 30 ppm/°C

Output Voltage VREF 2.048 V

INTERNAL TEMPERATURE SENSOR

Temperature Error (Note 1) -4 +4 °C

SPI SLAVE-MODE INTERFACE TIMING

Maximum SPI Clock Rate fSYS/4 MHz

SCLK Input Pulse-Width High tSCH (Note 3) 4 x

tSYS ns

SCLK Input Pulse-Width Low tSCL (Note 3) 4 x

tSYS ns

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

12 ______________________________________________________________________________________

ELECTRICAL CHARACTERISTICS (continued)

(VAVDD = VDVDD = VRST to 3.6V, TA= -40°C to +85°C, unless otherwise noted.) (Note 2)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

SSEL Low to First SCLK Edge

(Slave Enable) tSE (Note 3) 4tSYS ns

Last SCLK Edge to SSEL High

(Slave Disable) tSD tSYS +

5 ns

MOSI Valid to SCLK Sample

Edge (MOSI Setup) tSIS 5 ns

SCLK Sample Edge to MOSI

Change (MOSI Hold) tSIH tSYS +

5 ns

SCLK Shift Edge to MISO Valid

(MISO Hold) tSOV 3tSYS

+ 5 ns

Note 1: Specifications guaranteed by design but not production tested.

Note 2: Specifications to -40°C are guaranteed by design and are not production tested.

Note 3: tSYS = 1/fSYS.

SPI Slave Mode Timing

SSEL SHIFT EDGE SAMPLE EDGE

SCLK

DATA OUTPUT

DATA INPUT

tSD

tSE

tSOV

tSIS tSIH

tSCL tSCH

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 13

Block Diagram

MAXQ3180

CFP, CFQ

COUNTERS I/O

BUFFERS

I/O

REGISTERS

ADC

CFQ

CFP

V2P

I0P

V0P

VCOMM

RESET

VREF

V1P

I1P

I2P

INP

SPI I/O

BUFFERS

I/O

REGISTERS

WATCHDOG

TIMER

ADC CLOCK

PRESCALER

MISO

MOSI

SCLK

SSEL

XTAL1

SYSCLK

ADCCLK XTAL2

I/O

BUFFERS

I/O

REGISTERS

HF RC

OSC/8

XTAL

OSC

POR/

BROWNOUT

MONITOR

16 x 16

HW MULTIPLY

48-BIT ACCUMULATE

IRQ

I2N

I0N

I1N

TEMP

SENSE

REF

ADC CONTROL,

ELECTRICITY

METERING DSP,

COMMUNICATIONS

MANAGER

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

14 ______________________________________________________________________________________

Pin Description

PIN NAME FUNCTION

POWER PINS

17, 22 DVDD Digital Supply Voltage

25 AVDD Analog Supply Voltage

18 DGND Digital Ground

9 AGND Analog Ground

23 VCOMM

Voltage Bias. This pin can be used to create an input common-mode DC offset for ADC channel

conversions.

24 VREF

Voltage Reference. Reference voltage for the ADC. An external reference voltage can be connected to

this pin when extremely high accuracy is required.

VOLTAGE AND CURRENT PINS

26, 3, 4 V0P, I0P,

I0N Phase A Voltage and Current Analog Inputs

27, 5, 6 V1P, I1P,

I1N Phase B Voltage and Current Analog Inputs

28, 7, 8 V2P, I2P,

I2N Phase C Voltage and Current Analog Inputs

1 VN Analog Input for Common Voltage

2 INP Analog Input for Neutral Current

CLOCK PINS

10 XTAL2

11 XTAL1

High-Frequency Crystal Input/Output. When using an external high-frequency crystal, the crystal

oscillator circuit should be connected between XTAL1 and XTAL2. When using an externally driven

clock (EXTCLK = 1), the clock should be input at XTAL1, with XTAL2 left unconnected.

12 IRQ Interrupt Request Output. This line is driven low by the device to indicate to the master that an

unmasked interrupt has occurred.

13 SSEL Slave Select Input. This line is the active-low slave select input for the SPI interface.

14 SCLK Slave Clock Input. This line is the clock input for the SPI interface.

15 MOSI

Master Out-Slave In Input. This line is used by the master to transmit data to the slave (the

MAXQ3180) over the SPI interface.

16 MISO

Master In-Slave Out Output. This line is used by the MAXQ3180 (the slave) to transmit data back to

the master over the SPI interface.

19 CFP Pulse Output 1. Configurable to represent energy or RMS voltage or current.

20 CFQ Pulse Output 2. Configurable to represent energy or RMS voltage or current.

21 RESET

Active-Low Reset Input/Output. An external master can reset the MAXQ3180 by driving this pin low.

This pin includes a weak pullup resistor to allow for a combination of wired-OR external reset

sources. An RC circuit is not required for power-up, as this function is provided internally. This pin

also acts as a reset output when the source of the reset is internal to the device (power-fail, watchdog

reset, etc.). In this case, the RESET pin is held low by the device until it exits the reset state, then the

RESET pin is released.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 15

Detailed Description

The MAXQ3180 contains four major subsections: the

analog front-end, the digital signal processor, the preci-

sion pulse generators, and an SPI peripheral for com-

munication to the host processor.

Analog Front-End

The analog front-end (AFE) is an 8-channel analog-to-

digital converter (ADC). It operates autonomously in the

standard configuration, assigning three channels to

phase A, B, and C voltage; three channels to phase A,

B, and C current; one channel to neutral current; and

the last channel to a temperature sensor.

Each channel also contains a programmable-gain

amplifier capable of providing a gain of 1, 2, 4, 8, 16, or

32 incoming signals. Only the voltage channels permit

gain scaling by the host processor. The MAXQ3180

DSP firmware automatically sets the gain on current

channels.

Digital Signal Processor

The DSP code is permanently embedded in masked

ROM and accepts raw current and voltage samples for

each of three phases and continuously calculates a

host of values including RMS volts, RMS amps, real

energy, reactive energy, apparent energy, fundamental

and harmonic energy, and power factor.

The MAXQ3180 DSP core processes incoming sam-

ples from the analog front-end according to user con-

figurations. The host sets these operating parameters

by specifying addresses within the device RAM space.

When a calculation cycle is complete, the results are

placed back into RAM as well. Thus, the DSP core uses

the RAM block as both its input (for operating parame-

ters) and output (for calculation results) medium. See

the

SPI Peripheral

section for how the host writes oper-

ating parameters and reads results from the RAM.

The DSP also calculates certain values such as line fre-

quency and active and reactive powers only when

demanded by the host.

Precision Pulse Generators

The MAXQ3180 includes two precision pulse genera-

tors that generate a pulse whenever certain conditions

are met. In the MAXQ3180, many meter quantities can

be selected for conversion to meter pulses including

absolute energy, net energy, reactive energy, voltage,

and current.

The pulse generators are accumulators. On each DSP

cycle, whatever quantity is being measured—real ener-

gy, reactive energy, current, or something else—is

added to the pulse accumulator. The pulse accumula-

tor is then tested to determine if the value in the accu-

mulator is greater than the threshold. If it is greater, the

threshold value is subtracted from the accumulator

value and the meter pulse starts.

SPI Peripheral

The SPI controller is a slave-only device that can read

or write any location in the data RAM. Additionally, it

can request data from on-demand registers.

The MAXQ3180 implements a truly full-duplex commu-

nication, rather than the pseudo half-duplex mode used

by other SPI peripherals. That is, each time a character

is received by the MAXQ3180, a meaningful character

is returned to the host. Often, this is a protocol charac-

ter. In this way, the host can be assured that the com-

mand has been received and is valid. Optional error

checking can also be enabled to further guarantee

proper operation.

Operating Modes

The MAXQ3180 has two basic modes of operation,

each of which is described in the following sections.

The Initialization Mode is the default mode upon power-

up or following reset; entry to and exit from the other

operating modes is only performed as a result of com-

mands sent by the master.

Run Mode

This mode is the normal operating mode for the

MAXQ3180. In this mode, the MAXQ3180 continuously

executes the following operations:

• Scans analog front-end channels and collects raw

voltage and current samples.

• Processes voltage and current samples through DSP

filters as enabled and configured.

• Calculates power, energy, and other required quanti-

ties and stores these values in RAM registers.

• Responds to register write and read commands from

the master.

• Outputs power pulses on CFP and CFQ as configured.

• Drives IRQ when an interrupt condition has been

detected and the interrupt is not masked.

Stop Mode

This mode places the MAXQ3180 into a power-saving

state where it consumes the least possible amount of

current. In Stop Mode, all functions are suspended,

including the ADC and power and voltage measurement

and processing. The MAXQ3180 does not respond to

any commands from the master in this operating state.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

16 ______________________________________________________________________________________

Entry into Stop Mode only occurs at the request of the

master. To place the MAXQ3180 into Stop Mode, the

master must read the ENTER STOP (0xC02) register.

Once this register has been read, the MAXQ3180

enters Stop Mode immediately, before the transmission

of the final ACK byte by the MAXQ3180.

There are three possible ways to bring the MAXQ3180

back out of Stop Mode.

•Power Cycle. The MAXQ3180 automatically exits

Stop Mode if a power-on reset occurs. Following exit

from Stop Mode, all registers are cleared back to

their default states, and the MAXQ3180 transitions to

Initialization Mode.

•External Reset. The MAXQ3180 exits Stop Mode if

an external reset is triggered by driving RESET low.

Once the RESET pin is released and allowed to

return to a high state, the MAXQ3180 comes out of

reset and goes into Initialization Mode. All registers

are cleared to their default states when exiting Stop

Mode in this manner.

•External Interrupt. Driving the SSEL pin low causes

the MAXQ3180 to exit Stop Mode without undergoing

a reset cycle. When exiting Stop Mode in this man-

ner, all register and configuration settings are

retained, and the MAXQ3180 automatically resumes

electric-metering functions and sample processing.

Note that when the master is communicating with the

MAXQ3180, the SSEL line is normally driven low at the

beginning of each SPI command. This means that if the

master sends an SPI command after the MAXQ3180

enters Stop Mode, the MAXQ3180 automatically exits

Stop Mode.

Reset Sources

There are several different sources that can cause the

MAXQ3180 to undergo a reset cycle. For any type of

hardware reset, the RESET pin is driven low when a

reset occurs.

External Reset

This hardware reset is initiated by an external source

(such as the master controller or a manual pushbutton

press) driving the RESET pin on the MAXQ3180 low.

The RESET line must be held low for at least four cycles

of the currently selected clock for the external reset to

take effect. Once the external reset takes effect, it

remains in effect indefinitely as long as RESET is held

low. Once the external reset has been released, the

MAXQ3180 clears all registers to their default states

and resumes execution in Initialization Mode.

When an external reset occurs outside of Stop Mode,

execution (in Initialization Mode) resumes after four

cycles of the currently selected clock (external high-fre-

quency crystal for Run Mode, 1MHz internal RC oscilla-

tor for LOWPM Mode). As the MAXQ3180 enters

Initialization Mode, the LOWPM bit is always cleared

CLOCK

RESET

SAMPLING

INTERNAL

RESET

BEGIN RUNNING IN INITIALIZATION MODE

Figure 1. External Reset

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 17

tPOR

VRST1

BROWNOUT DETECTION

BROWNOUT DETECTION (ALWAYS

ENABLED OUTSIDE OF STOP MODE)

FORCES RESET STATE. POR = 1

BROWNOUT DETECTION DISABLED

DURING STOP MODE.

NO RESET IS GENERATED.

BROWNOUT DETECTION DISABLED.

POR LEVEL CAUSES RESET.

VPOR

INTERNAL

RESET

STOP MODE

Figure 2. Brownout Reset

to 0, meaning that the MAXQ3180 always switches to

the high-frequency clock before it begins accepting

commands in Initialization Mode.

When an external reset occurs from Stop Mode, execu-

tion (in Initialization Mode) resumes after 128 cycles of

the internal RC oscillator (or approximately 128μs).

Power-On Reset

When the MAXQ3180 is first powered up, or when the

power supply, VDVDD, drops below the VRST power-fail

trip point (outside of Stop Mode), the MAXQ3180 is

held in power-on reset. Once the power supply rises

above the VRST level, the power-on reset state is

released and all registers are reset to their defaults and

execution resumes in Initialization Mode. The high-fre-

quency external crystal (LOWPM = 0) is always select-

ed as the clock source following any power-on or

brownout reset.

In Stop Mode brownout detection is disabled, so a

power-on reset does not occur until VDVDD drops to a

lower level (VPOR). From the master’s perspective,

power-on resets and brownout resets both cause the

MAXQ3180 to reset in the same way.

Watchdog Reset

The MAXQ3180 includes a hardware watchdog timer that

is armed and periodically reset automatically during nor-

mal operation. Under normal circumstances, the

MAXQ3180 always resets the watchdog timer often

enough to prevent it from expiring. However, if an internal

error of some kind causes the MAXQ3180 to lock up or

enter an endless execution loop, the watchdog timer

expires and triggers an automatic hardware reset. There

is no register flag to indicate to the master that a watch-

dog reset has occurred, but the RESET line strobes low

briefly.

The watchdog timer does not run during Stop Mode.

Software Reset

The master initiates a software reset by setting the

SWRES (OPMODE0.3) bit to 1. When a software reset

occurs, the MAXQ3180 clears all registers to their

default states and returns to Initialization Mode, in the

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

18 ______________________________________________________________________________________

same manner as if an external reset had taken place.

Unlike a hardware reset, however, a software reset does

not cause the MAXQ3180 to drive the RESET line low.

Power-Supply Monitoring

In addition to the hardware reset provided by the

power-on reset and brownout reset circuits, the

MAXQ3180 includes the capability to detect a low

power supply on the DVDD pin and alert the master

through the interrupt (IRQ) mechanism before a hard-

ware reset occurs. This function, which is always

enabled outside of Stop Mode, causes the RAM status

ever VDVDD drops below the VPFW trip point. Once

PWRF has been set to 1 by hardware, it can only be

cleared by the master (or by a system reset). Whenever

PWRF = 1, if the EPWRF interrupt masking bit is also

set to 1, the MAXQ3180 drives IRQ low to signal to the

master that an interrupt condition (in this case, a power-

fail warning) exists and requires attention.

Clock Sources

All operations including ADC sampling and SPI com-

munications are synchronized to a single system clock.

This clock can be obtained from any one of three selec-

table sources, as shown in Figure 3.

External High-Frequency Crystal

The default system clock source for the MAXQ3180 is

an external high-frequency crystal oscillator circuit con-

nected between XTAL1 and XTAL2. When clocked with

an external crystal, a parallel-resonant, AT-cut crystal

oscillating in the fundamental mode is required.

When using a high-frequency crystal, the fundamental

oscillation mode of the crystal operates as inductive

reactance in parallel resonance with external capaci-

tors C1 and C2. The typical values of these external

capacitors vary with the type of crystal being used and

should be selected based on the load capacitance as

suggested by the crystal manufacturer.

Since noise at XTAL1 and XTAL2 can adversely affect

device timing, the crystal and capacitors should always

be placed as close as possible to the XTAL1 and

XTAL2 pins, with connection traces between the crystal

and the device kept as short and direct as possible. In

multiple layer boards, avoid running other high-speed

digital signals underneath the crystal oscillator circuit if

possible, as this could inject unwanted noise into the

clock circuit.

Following power-up or any system reset, the high-fre-

quency clock is automatically selected as the system

clock source. However, before this clock can be used

XTAL IN

RING IN

SYSTEM CLOCK

EXTCLK

STOPM

POR

CLK

ENABLE WATCHDOG RESETRING COUNT

INT/EXT

CRYSTAL

STARTUP TIMER

WATCHDOG TIMER

1MHz

INTERNAL

OSCILLATOR

CRYSTAL

GLITCH-FREE

MUX

ENABLE

CLOCK

GENERATION

Figure 3. Simplified Clock Sources

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 19

for system execution, a crystal warmup timer must

count 65,536 cycles of the high-frequency clock. While

this warmup time period is in effect, execution contin-

ues using the internal 1MHz oscillator. Once the

65,536-cycle count completes (which requires approxi-

mately 8.2ms at 8MHz), the device automatically

switches over to the high-frequency clock. This crystal

warmup timer is also activated upon exit from Stop

Mode, since the high-frequency crystal oscillator is shut

down during Stop Mode.

External High-Frequency Clock

Instead of using a crystal oscillator to generate the

high-frequency clock, it is also possible to input a high-

frequency clock that has been generated by another

source (such as a digital oscillator IC) directly into the

XTAL1 pin of the MAXQ3180.

To use an external high-frequency clock as the system

clock source, the XTAL1 pin should be used as the

clock input and the XTAL2 pin should be left uncon-

nected. The master should also shut down the internal

crystal oscillator circuit by setting the EXTCLK bit

(OPMODE0.4) to 1. This bit is only cleared by the

MAXQ3180 if a power-on or brownout reset occurs and

is unaffected by other resets.

When using an external high-frequency clock, the clock

signal should be generated by a CMOS driver. If the

clock driver is a TTL gate, its output must be connected

to DVDD through a pullup resistor to ensure that the

correct logic levels are generated. To minimize system

noise in the clock circuitry, the external clock source

must meet the maximum rise and fall times and the

minimum high and low times specified for the clock

source in the

Electrical Characteristics

table.

Internal RC Oscillator

When the external high-frequency crystal is warming

up, or when the MAXQ3180 is placed into LOWPM

mode, the system clock is sourced from an internal RC

oscillator. This internal oscillator is designed to provide

the system approximately 1MHz, although the exact

frequency varies over temperature and supply voltage.

If no external crystal circuit or high-frequency clock will

be used, the MAXQ3180 can be forced to operate infi-

nitely from the internal oscillator by grounding XTAL1.

This ensures that the crystal warmup count never com-

pletes, so the MAXQ3180 runs from the internal oscilla-

tor in all active modes.

Master Communications

Before the MAXQ3180 can begin performing electric-

metering operations, the master must initialize a num-

ber of configuration parameters. Since the MAXQ3180

does not contain internal nonvolatile memory, these

parameters (stored in internal registers) must be set by

the master each time a power-up or reset cycle occurs,

or each time a switch is made between LOWPM Mode

and Run Mode.

The external master communicates with the MAXQ3180

over a standard SPI bus, using commands to read and

write values to internal registers on the MAXQ3180.

These registers include, among many other items:

• Operating mode settings (Stop Mode, LOWPM

Mode, external clock mode, etc.)

• Status and interrupt flags (power-supply failure, over-

current/overvoltage detection, etc.)

• Masking control for interrupts to determine which

conditions cause IRQ to be driven low

• Configuration settings for analog channel scanning

• Power pulse output configuration

• Filter coefficients and configuration

• Read-only registers containing accumulated power

and energy data

As the MAXQ3180 obtains voltage and current mea-

surements in Run Mode or LOWPM Mode, it accumu-

lates, filters, and performs a number of calculations on

the collected data. Many of these operations (including

the various filtering stages) are configured by settings

in registers written by the master. The output results

can then be read by the master from various read-only

registers in parallel with the ongoing measurement and

processing operations.

SPI Communications Rate and Format

The SPI is an interdevice bus protocol that provides

fast, synchronous, full-duplex communications between

a designated master device and one or more slave

devices. In a MAXQ3180-based design, the

MAXQ3180 would be the slave device connected to a

designated master microcontroller.

The external master initiates all communications trans-

fers. The interrupt request line IRQ, while not technical-

ly part of the SPI bus interface, is also used for

master/slave communications because it allows the

MAXQ3180 to notify the master that an interrupt condi-

tion exists. Some SPI peripherals sacrifice speed in

favor of simulating a half-duplex operation. This is not

the case with the MAXQ3180; it is truly a full-duplex SPI

slave.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

20 ______________________________________________________________________________________

During an SPI transfer, data is simultaneously transmit-

ted and received over two serial data lines (MISO and

MOSI) with respect to a single serial shift clock (SCLK).

The polarity and phase of the serial shift clock are the

primary components in defining the SPI data transfer

format. The polarity of the serial clock corresponds to

the idle logic state of the clock line and, therefore, also

defines which clock edge is the active edge. To define

a serial shift clock signal that idles in a logic-low state

(active clock edge = rising), the clock polarity select

(CKPOL; R_SPICF.0) bit should be configured to a 0,

while setting CKPOL = 1 causes the shift clock to idle in

a logic-high state (active clock edge = falling). The

phase of the serial clock selects which edge is used to

sample the serial shift data. The clock phase select

(CKPHA; R_SPICF.1) bit controls whether the active or

inactive clock edge is used to latch the data. When

CKPHA is set to a logic 1, data is sampled on the inac-

tive clock edge (clock returning to the idle state). When

CKPHA is set to a logic 0, data is sampled on the active

clock edge (clock transition to the active state).

Together, the CKPOL and CKPHA bits allow four possi-

ble SPI data transfer formats.

Transfers over the SPI interface always start with the

most significant bit and end with the least significant

bit. All SPI data transfers to and from the MAXQ3180

are always 8 bits (one byte) in length. The MAXQ3180

SPI interface does not support 16-bit character lengths.

The default format (upon power-up or system reset) for

the MAXQ3180 SPI interface is represented in

Figure 4a (CKPOL = 0; CKPHA = 0). In this format, the

SCLK CYCLE #

(FOR REFERENCE)

SCLK (CKPOL = 0)

SCLK (CKPOL = 1)

MOSI

(FROM MASTER)

MISO

(FROM SLAVE)

SSEL (TO SLAVE)

MSB 6 5 4 3 2 1 LSB

2345678

6MSB

*NOT DEFINED BUT NORMALLY MSB OF CHARACTER JUST RECEIVED.

5 4 3 2 1 LSB *

MSB 6 5 4 3 2 1 LSB

2345678

MSB*

*NOT DEFINED BUT NORMALLY LSB OF PREVIOUSLY TRANSMITTED CHARACTER.

6 5 4 3 2 1 LSB

SCLK CYCLE #

(FOR REFERENCE)

SCLK (CKPOL = 0)

SCLK (CKPOL = 1)

MOSI

(FROM MASTER)

MISO

(FROM SLAVE)

SSEL (TO SLAVE)

Figure 4b. SPI Interface Timing (CKPHA = 1)

Figure 4a. SPI Interface Timing (CKPHA = 0)

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 21

SPI clock idle state is low, and data is shifted in and out

on the rising edge of SCLK. Once SPI communication

with the MAXQ3180 has been established, it is possible

to alter the CKPOL and CKPHA format settings (as well

as changing the SSEL signal from active low to active

high) if desired by writing to the R_SPICF mirror register

and then reading from the special command register

UPD_SFR to copy the R_SPICF value into the internal

SPI configuration register.

Whenever the active clock edge is used for sampling

(CKPHA = 0), the transfer cycle must be started with

assertion of the SSEL signal. This requirement means

that the SSEL signal be deasserted and reasserted

between successive transfers. Conversely, when the

inactive edge is used for sampling (CKPHA = 1), the

SSEL signal may remain low through successive

transfers, allowing the active clock edge to signal the

start of a new transfer.

The clock rate used for the SPI interface is determined

by the bus master, since the MAXQ3180 always oper-

ates as an SPI slave device. However, the maximum

clock rate is limited by the system clock frequency of

the MAXQ3180. For proper communications operation,

the SPI clock frequency used by the master must be

less than or equal to the MAXQ3180’s clock frequency

divided by 4. For example, when the MAXQ3180 is run-

ning at 8MHz, the SPI clock frequency must be 2MHz

or less. And if the MAXQ3180 is running in LOWPM

Mode (or if the crystal is still warming up), the SPI clock

frequency must remain at 250kHz or less for proper

communications operation.

In addition to limiting the overall SPI bus clock rate, the

master must also include a communications delay fol-

lowing each byte transmit/receive cycle. This delay,

which provides the MAXQ3180 with time to process an

ADC sample, should be a minimum of 400 system

clocks. With default settings and running at 8MHz, this

delay time is 50μs. Reducing the system clock frequen-

cy to 1MHz (LOWPM mode) would increase this delay

period by a factor of 8 to 400μs.

SPI Communications Protocol

All transactions between the master and the

MAXQ3180 consist of the master writing to or reading

from one of the MAXQ3180’s registers. To the host, the

MAXQ3180 looks like a memory array that consists of

both RAM and ROM. This is because the ROM firmware

in the MAXQ3180 reads its operational parameters from

RAM and places its results in RAM. Consequently, con-

figuring a MAXQ3180 is as simple as performing a

block write to its RAM locations.

Some read-only memory locations in the MAXQ3180

trigger actions within the device to calculate electricity-

metering results on the fly. The specific function and

purpose of RAM and virtual ROM locations are given in

the register map. There are several different categories

of internal registers on the MAXQ3180.

•RAM Registers. The values of these registers are

stored in the internal RAM of the MAXQ3180. Some

can be read and written by the master, while others

are read-only. RAM registers are either 2 or 4 bytes

long (16 or 32 bits), although in some registers not all

the bits have defined values. Read/write registers are

generally either status/flag registers (which can be

written by either the MAXQ3180 or the master), con-

figuration registers (which are written by the master

and read by the MAXQ3180 firmware), or data regis-

ters (which are read-only and are written by the

MAXQ3180 firmware and read by the master).

•Virtual Registers. These read-only registers are not

stored in RAM; instead, they contain values that are

calculated on the fly by the MAXQ3180 firmware

when the master reads them. These registers are

used by the master to obtain values such as phase

A, B, and C active, reactive, and apparent power;

power factor; and RMS voltage and current, which

are calculated from currently collected data on an

as-needed basis. Most virtual registers are 8 bytes in

length.

•Hardware Registers. These registers control core

functions of the MAXQ3180 including the ADC and

the SPI slave bus controller. Each of these registers

(R_ACFG, R_ADCRATE, R_ADCACQ, R_SPICF, and

OPMODE0 (bit 4, EXTCLK only)) has a register loca-

tion in RAM that “shadows” the value of the hardware

ter must first read from the special command register

UPD_MIR (A00h) to copy the values from the hard-

ware registers to the mirror registers in RAM, and

then the mirror register in RAM can be read. To write

to a hardware register, the master reverses the

process by writing to the mirror RAM register and

then reading from the special command register

UPD_SFR (900h) to copy the values from the mirror

registers to the hardware registers.

•Special Command Registers. These registers

(UPD_SFR and UPD_MIR) do not return meaningful

data when read but instead trigger an operation.

Reading UPD_SFR causes values to be copied from

the mirror registers to hardware, and reading

UPD_MIR causes values to be copied from the hard-

ware to mirror registers.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

22 ______________________________________________________________________________________

Every defined register on the MAXQ3180 has a 12-bit

address (from 0 to 4095). This address is used when

addressing the register for either a read or write opera-

tion. Addresses 0 to 1023 (000h to 3FFh) are used to

address RAM registers. Registers with addresses from

1024 to 4095 (400h to FFFh) are used for virtual regis-

ters and special command registers.

Each command consists of a read/write command

code, a data length (1, 2, 4, or 8 bytes), a 12-bit regis-

ter address, and the specified number of data bytes fol-

lowed optionally by a cyclic redundancy check (CRC).

Since SPI is a full-duplex interface, the master and

slave must both transmit the same number of bytes dur-

ing the command. When a multiple-byte register is read

or written (2/4/8 byte length), the least significant byte is

read or written first in the command.

Every transaction begins with the master sending 2

bytes that contain the command (read or write), the

address to access, and the number of bytes to transfer.

Every SPI peripheral must return 1 byte for every byte it

receives. If the master is reading 1 or more bytes from

the MAXQ3180, it must send dummy bytes during the

cycles when it is receiving a multibyte response to a

request, meeting the “send a byte to get a byte” require-

ment. But the MAXQ3180 could require time to calculate

the result, and thus might not have it ready when the

master sends the dummy byte. For this reason, the

MAXQ3180 always sends zero or more bytes of a NAK

character (0x4E or ASCII ‘N’) followed by an ACK char-

acter (0x41, or ASCII ‘A’) before sending the data.

If the master is writing 1 or more bytes, it sends the

data to be written immediately after sending the com-

mand. The MAXQ3180 returns ACK (0x41) for each

data byte. It then returns NAK (0x4E) until the write

cycle is complete, after which it returns a final ACK.

Immediately after the final ACK, the MAXQ3180 is

ready to begin the next transaction; there is no need to

wait for any other event. It is not even necessary to tog-

gle SSEL to begin the next transaction. The MAXQ3180

knows that the first transaction is over and is ready for

the next.

If, for whatever reason, it is necessary to reset the com-

munications between the host and the MAXQ3180 (for

Table 1. Command Format for SPI Register Read

BYTE TRANSFERS BIT DESCRIPTION

7:6

Command Code:

00 Read

01 Reserved

10 Write

11 Reserved

5:4

Data Length:

00 1 Byte

01 2 Bytes

10 4 Bytes

11 8 Bytes

1st byte Master sends command;

Slave sends 0xC1 byte

3:0 MSB portion of data address.

2nd byte Master sends address;

Slave sends 0xC2 byte 7:0 LSB portion of data address.

Sync bytes

Master sends dummy;

Slave sends ACK (0x41) or

NACK (0x4E) byte

7:0

Master sends dummy byte; Slave responds with NACK if busy,

or with ACK when processing complete.

Master must receive ACK, then receive data.

3rd byte

(1st data byte)

Master sends dummy;

Slave sends data 7:0 Data, LSB

... ... ... ...

Nth byte

(Last data byte)

Master sends dummy;

Slave sends data 7:0 Data, MSB

(N + 1) byte Master sends dummy;

Slave sends CRC 7:0 Optional CRC

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 23

Table 2. Command Format for SPI Register Write

BYTE TRANSFERS BIT DESCRIPTION

7:6

Command code:

00 Read

01 Reserved

10 Write

11 Reserved

5:4

Data Length:

00 1 Byte

01 2 Bytes

10 4 Bytes

11 8 Bytes

1st byte Master sends command;

Slave sends 0xC1 byte

3:0 MSB portion of data address.

2nd byte Master sends address;

Slave sends 0xC2 byte 7:0 LSB portion of data address.

3rd byte

(1st data byte)

Master sends data;

Slave sends ACK (0x41) 7:0 Data, LSB

... ... ... ...

Nth byte

(Last data byte)

Master sends data;

Slave sends ACK (0x41) 7:0 Data, MSB

(N + 1) byte Master sends CRC;

Slave sends ACK (0x41) 7:0 Optional CRC

Sync bytes

Master sends dummy;

Slave sends ACK (0x41) or

NACK (0x4E) byte

7:0

Master sends dummy byte; Slave responds with NACK if busy,

or with ACK when processing complete.

Master must receive ACK before starting the next transaction.

example, if synchronization is lost), the host only needs

to wait for the SPI to time out before restarting commu-

nication from the first command byte. SPI timeout count

starts after receiving the first command byte from the

master (after the 8th SPI clock of the first byte). The

count stops and clears after receiving the last byte of a

transaction (after the 8th SPI clock of the last byte).

If the timeout count expires (exceeds COM_TIMO)

before the transaction completes, the MAXQ3180 aban-

dons the unfinished transaction and resets the SPI logic

to be ready for the next transaction. The default SPI

timeout is 320ms.

Optionally, a CRC byte can be appended to each

transaction. For write commands, the CRC byte is sent

by the master, and for read commands the CRC byte is

sent by the MAXQ3180. The CRC mode is enabled

when the CRCEN bit is set to 1 in OPMODE1 register.

Otherwise, the MAXQ3180 assumes no CRC byte is

used. The 8-bit CRC is calculated for all bytes in a

transaction, from the first command byte sent by the

master through the last data byte excluding sync bytes,

using the polynomial P = x8+ x5+ x4+ 1. If the trans-

mitted CRC byte does not match the calculated CRC

byte (for a write command), the MAXQ3180 ignores the

command.

The length of the transfer is defined by the first com-

mand byte and the status of the CRCEN bit in the

OPMODE1 register. There is no special synchronization

mechanism provided in this simple protocol. Therefore,

the master is responsible for sending/receiving the cor-

rect number of bytes. If the master mistakenly sends

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

24 ______________________________________________________________________________________

more bytes than are required by the current command,

the extra bytes are either ignored (if the MAXQ3180 is

busy processing the previous command) or are inter-

preted as the beginning of a new command. If the mas-

ter sends fewer bytes than are required by the current

command, the MAXQ3180 waits for SPI timeout, then

drops the transaction and resets the communication

channel. The duration of the timeout can be configured

through the COM_TIMO register.

Figures 5 and 6 show typical 2-byte reading and writing

transfers (without CRC byte).

Host Software Design

Individual message bytes sent through the SPI are

processed in a software routine contained in the ROM

firmware. For this reason, it is necessary to provide a

delay between successive bytes. This byte spacing

must be no less than 400 system clocks to ensure that

the MAXQ3180 has a chance to read and process the

byte before the arrival of the next one.

To read any virtual power registers, the host must first

confirm that the DSPRDY bit of the IRQ_FLAG register

is set, which indicates the last DSP cycle has complet-

ed, then proceed to reading all the desired virtual

power registers. For best communication efficiency, it is

recommended to complete reading the virtual power

registers before reading other registers. Virtual power

cycle time, from the moment the DSPRDY bit is set. Do

not forget to clear the DSPRDY bit, otherwise, host soft-

ware is not able to detect the completion of the new

DSP cycle. The MAXQ3180 does not clear the bit; it

only sets the bit whenever a DSP cycle processing is

completed. Users can clear the bit directly after the

confirmation that the bit is set. Clearing the DSPRDY bit

does not affect the DSP processing. It is strongly rec-

ommended that CRC be enabled for both read and

write to achieve reliable communications.

SSEL

SCLK

MOSI

MISO

READING DATA FROM MAXQ3180 THROUGH SPI INTERFACE

00 01 ADDRESS DUMMY DUMMY DUMMY DUMMY

0xC1 0xC2 NACK (0x4E) DATA LSB DATA MSBACK (0x41)

SSEL

SCLK

MOSI

MISO

10 01 ADDRESS DUMMY DUMMY

0xC1 0xC2 ACK (0x41) NACK (0x4E) ACK (0x41)ACK (0x41)

WRITING DATA TO MAXQ3180 THROUGH SPI INTERFACE

DATA LSB DATA MSB

Figure 6. Write SPI Transfer

Figure 5. Read SPI Transfer

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 25

READ MAXQ3180

SEND COMMAND BYTE 1

GET 0xC1?

GET 0xC2?

EXIT

SPI TIMEOUT (320ms)

DELAY > 400 SYSCLK

SEND COMMAND BYTE 2

SEND 0x00

DELAY > 400 SYSCLK

SEND 0x00

GET DATA BYTE

DELAY > 400 SYSCLK

GET 0x4E?

GET 0x41?

DONE?

WRITE MAXQ3180

SEND COMMAND BYTE 1

GET 0xC1?

GET 0xC2?

EXIT

SPI TIMEOUT (320ms)

DELAY > 400 SYSCLK

SEND COMMAND BYTE 2

SEND DATA BYTE

DELAY > 400 SYSCLK

SEND 0x00

DELAY > 400 SYSCLK

GET 0x4E?

GET 0x41?

DONE?

GET 0x41?

Figure 8. Flowchart for Writing to MAXQ3180Figure 7. Flowchart for Reading from MAXQ3180

Data and device command and control information are

located in internal registers. Registers range from 8 to 64

bits in length and are divided into RAM-based registers

and virtual registers. The RAM-based registers contain

both operating parameters and measurement results.

The virtual registers contain calculated values derived

from one or more real registers. They are calculated at

the time they are requested, and thus can involve addi-

tional time to return a value. Most virtual registers are 8

bytes in length and are delivered least significant byte

first.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

26 ______________________________________________________________________________________

Table 3. RAM Register Map

x0h x1h x2h x3h x4h x5h x6h x7h x8h x9h xAh xBh xCh xDh xEh xFh

0x00 STATUS OP

MODE0

MODE1

MODE2 IRQ_FLAG IRQ_MASK

SCAN

_IA

SCAN

_VA

SCAN

_IC

SCAN

_VC

SCAN

_IB

SCAN

_VB

SCAN

_IN

SCAN

_TE

0x01 AUX_CFG SYS_KHZ VOLT_CC AMP_CC PWR_CC ENR_CC CYCNT PLSCFG

PLSCFG

0x02 PLS1_WD THR1 PLS2_WD THR2 REJ_NS AVG_NS

0x03 AVG_C HPF_C B0FUND A1FUND B0HARM A1HARM

0x04 NS OCLVL OVLVL UVLVL NOLOAD R_ACFG R_ADCRATE

0x05 R_ADCACQ R_

SPICF NZX_TIMO COM_TIMO ACC_TIMO ZC_LPF I1THR I2THR

0x06 CHKSUM LINEFR

0x11 N.IRMS

0x12 N.I_GAIN

PHASE A CALIBRATION AND STATUS REGISTERS

0x13 A.I_GAIN A.V_GAIN A.E_GAIN A.EF_GAIN A.OFFS_HI A.GAIN_LO A.OFFS_LO A.PA0

0x14 A.PA1 A.PA2 A.

FLAGS

MASK

EOVER

EFOVER

PHASE B CALIBRATION AND STATUS REGISTERS

0x21 B.I_GAIN B.V_GAIN

0x22 B.E_GAIN B.EF_GAIN B.OFFS_HI B.GAIN_LO B.OFFS_LO B.PA0 B.PA1 B.PA2

0x23 B.

FLAGS

MASK

EOVER

EFOVER

PHASE C CALIBRATION AND STATUS REGISTERS

0x30 C.I_GAIN C.V_GAIN C.E_GAIN C.EF_GAIN

0x31 C.OFFS_HI C.GAIN_LO C.OFFS_LO C.PA0 C.PA1 C.PA2

FLAGS

MASK

EOVER

EFOVER

0x32

PHASE A MEASUREMENT REGISTERS*

0x1C A.PF A.VRMS A.IRMS

0x1D A.ACT A.REA A.APP A.ACTF

0x1E A.REAF A.APPF A.EAPOS A.EANEG

0x1F A.ERPOS A.ERNEG A.ES A.EAFPOS

0x20 A.EAFNEG A.ERFPOS A.ERFNEG A.ESF

PHASE B MEASUREMENT REGISTERS*

0x2B B.PF B.VRMS B.IRMS B.ACT

0x2C B.REA B.APP B.ACTF B.REAF

0x2D B.APPF B.EAPOS B.EANEG B.ERPOS

0x2E B.ERNEG B.ES B.EAFPOS B.EAFNEG

0x2F B.ERFPOS B.ERFNEG B.ESF

PHASE C MEASUREMENT REGISTERS*

0x39 C.PF

0x3A C.VRMS C.IRMS C.ACT C.REA

0x3B C.APP C.ACTF C.REAF C.APPF

0x3C C.EAPOS C.EANEG C.ERPOS C.ERNEG

0x3D C.ES C.EAFPOS C.EAFNEG C.ERFPOS

0x3E C.ERFNEG C.ESF

Read-only.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 27

x0 x1 x2 x3 x4 x5 x6 x7

0x80 PWRP.A PWRP.B PWRP.C PWRP.T

0x81 PWRQ.A PWRQ.B PWRQ.C PWRQ.T

0x82 PWRS.A PWRS.B PWRS.C PWRS.T

0x83 V.HARM V.A V.B V.C

0x84 I.N, I.HARM I.A I.B I.C

0x85 HARM_NF VBPH VCPH

0x86 PF.T

0x87 ENRS.A ENRS.B ENRS.C ENRS.T

0x88 PWRPF.A PWRPF.B PWRPF.C PWRPF.T

0x89 PWRQF.A PWRQF.B PWRQF.C PWRQF.T

0x8A PWRSF.A PWRSF.B PWRSF.C PWRSF.T

0x8B ENRSF.A ENRSF.B ENRSF.C ENRSF.T

0x8C ENRP.A ENRP.B ENRP.C ENRP.T

0x8D ENRQ.A ENRQ.B ENRQ.C ENRQ.T

0x8E ENRPF.A ENRPF.B ENRPF.C ENRPF.T

0x8F ENRQF.A ENRQF.B ENRQF.C ENRQF.T

SPECIAL FUNCTION REGISTERS

0xC0 DSPVER RAWTEMP ENTER STOP ENTER

LOWPM EXIT LOWPM

Table 4. Virtual Register Map

Note: All virtual registers are read-only.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

28 ______________________________________________________________________________________

RAM-Based Registers

The RAM-based registers contain both operating parameters and measurement results. They are divided into a num-

ber of categories that are described in the following sections.

General Operating Registers

Global Status Register (STATUS) (0x000)

This register contains bits that reflect the global status of the device.

Bit: 7 6 5 4 3 2 1 0

Name: — CROFF PORF WDTR — PHSEQ REVCFQ REVCFP

Reset: 0 0 0 0 0 0 0 0

BIT NAME FUNCTION

7, 3 — Reserved.

6 CROFF

When set, the high-frequency crystal has failed and the MAXQ3180 is operating from its internal ring

oscillator. Under these circumstances, energy accumulation is not accurate and the SPI bus does not

operate at full speed.

5 PORF

When set, the last reset was due to power-on-reset. Host should clear this bit to allow the next POR

detection.

4 WDTR

When set, the last reset was caused by expired watchdog. The bit should be cleared (set to 0) by the

host to allow the next watchdog reset detection.

2 PHSEQ

0 = The sequence of voltages presented to the voltage inputs is (-A-B-C-).

1 = The sequence of voltages presented to the voltage inputs is reversed (-A-C-B-).

This bit is meaningful only for connection systems that include all three voltages.

1 REVCFQ

0 = The quantity being output on the CFQ pin is positive (direct).

1 = The quantity being output on the CFQ pin is negative (reverse).

0 REVCFP

0 = The quantity being output on the CFP pin is positive (direct).

1 = The quantity being output on the CFP pin is negative (reverse).

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 29

Operating Mode Register 1 (OPMODE1) (0x002)

BIT NAME FUNCTION

7:4 — Reserved.

3 CRCEN

If set, a 1-byte CRC is appended to the end of each SPI read and is expected at the end of each SPI

write. See the SPI Communication Protocols section for details about how to use the CRC byte for error

checking on the SPI bus.

2 POPOL

This bit sets the polarity of the output pulse generators. If clear, the pulse outputs are active low; that

is, they remain in the high state until a pulse event occurs, at which time they switch low for one

pulse-width interval before reverting to the high state. If set, the pulse outputs are active high; that is,

they remain in the low state until a pulse event occurs, at which time they switch to the high state for

one pulse-width interval before reverting to the low state.

Bit: 7 6 5 4 3 2 1 0

Name: — — — — CRCEN POPOL CONCFG

Reset: 0 0 0 0 0 0 0x0

Operating Mode Register 0 (OPMODE0) (0x001)

BIT NAME FUNCTION

7:5, 0 — Reserved.

4 EXTCLK

When set, the high-frequency crystal oscillator is disabled and the XTAL1 pin is configured to be a

clock input for the device. This is used when it is desired to operate multiple devices from the same

clock source for purposes of maintaining synchronization.

3 SWRES

When set, forces the internal software to restart from the reset vector. This has the same effect as a

power-on reset, but does not specifically reset any hardware peripherals. This bit is automatically

cleared after the reset.

2 DSPDIS

When set, disables the signal processing software routines. The CPU continues to run at full speed,

but only to perform supervisory functions (such as servicing the SPI port).

1 LOWPM

When set, causes the CPU to switch its clock source from the external crystal to an internal ring oscillator

that operates at a nominal frequency of 1MHz. In this mode, the CPU continues to run, but the host must

reconfigure the parameters configured for crystal operation (such as filter settings, timeouts, and pulse

widths).

Bit: 7 6 5 4 3 2 1 0

Name: — — — EXTCLK SWRES DSPDIS LOWPM —

Reset: 0 0 0 0 0 0 0 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

30 ______________________________________________________________________________________

Operating Mode Register 1 (OPMODE1) (0x002) (continued)

BIT NAME FUNCTION

These bits determine how power is calculated on each of the three phases.

PA = IA x VA

PB = IB x VB

PC = IC x VC

Use this configuration when the load is

connected in a wye arrangement and

neutral is connected to MAXQ3180 ground,

or when the load is connected in a delta

arrangement and isolated voltage and

current sensors are used. This

arrangement measures power in each load

branch rather than power in each source

branch.

PA = IA x VA

PB = IB x (-VC)

PC = IC x VC

Use this configuration when the load is

connected in a four-wire delta

arrangement. In this arrangement, the BC

leg is split and VB-N is expected to be

equal to -VC-N. Voltages are referenced to

neutral.

PA = IA x VA

PB = IB x (-VA - VC)

PC = IC x VC

Use this configuration when the load is

connected in a four-wire wye arrangement,

but only two voltage sensors are

available. When connected in this way,

phase B is assumed to be ground.

1:0 CONCFG

PA = IA x VA

PB = IB x (VA - VC)

PC = IC x VC

Use this configuration when the load is

connected as a three-wire delta and it is

desired to measure the voltage and current

inside the delta legs, but to calculate the

power in each of the source circuits. When

connected this way, source phase B is

considered ground.

V V

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 31

Operating Mode Register 2 (OPMODE2) (0x003)

BIT NAME FUNCTION

7 — Reserved.

6 DHARA

When set, disables automatic determination of the filter parameters for the harmonic filter coefficient. If

set by the host software, the host must set a value in the A1HARM filter coefficient register to

establish the operating frequency of this filter if harmonic-mode calculations are used. When cleared,

the MAXQ3180 automatically determines the value of the harmonic-filter coefficient based on the

measured line frequency and the harmonic-order requested (AUX_CFG.ORDH).

5 DFUNA

When set, disables automatic determination of the filter parameters for the fundamental-mode filter

described above. If set by the host software, the host must set a value in the A1FUND filter coefficient

When clear, the MAXQ3180 automatically determines the value of the fundamental-mode filter

coefficient based on the measured line frequency.

4 DFUN

When set, fundamental-mode calculations are disabled. Fundamental-mode calculations provide

information about power and energy that are consumed only at the fundamental line frequency apart

from any harmonics that could be present. Setting this bit disables all fundamental frequency registers

but allows the MAXQ3180 to calculate other parameters at a higher rate. Set this bit when (1)

fundamental mode values do not need to be read, and (2) R_ADCRATE needs to be reduced below its

default value.

3 LINFRM

Selects the current linearity offset calibration method. See the Calibrating Current Offset section for

more information.

0 =

IRMS

+OFFS

1 = IRMS + OFFS

These bits select the coefficient used in calculating apparent power.

00 = 1-phase, 3-wire (1P3W), or 3-phase, 4-wire (3P4W) (C = 1)

01 = 3-phase, 3-wire (3P3W) (C = 3/2)

10 = three voltages, three currents (3V3A) (C = 3/3)

2:1 WIRSYS

3P3W Wiring (01)

Bit: 7 6 5 4 3 2 1 0

Name: — DHARA DFUNA DFUN LINFRM WIRSYS APPSEL

Reset: 0 0 0 0 0 0 0 0

VAB

VCB

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

32 ______________________________________________________________________________________

Operating Mode Register 2 (OPMODE2) (0x003) (continued)

BIT NAME FUNCTION

3P4W Wiring (00)

3V3A (10)

2:1 WIRSYS

1P3W (00)

Selects the mechanism to use for calculating apparent power.

0: S = VRMS x IRMS Apparent power is calculated by multiplying, on a per-DSP cycle basis, the

product of the RMS volts and RMS amps.

0 APPSEL

S=P2+Q2

Apparent power is calculated by finding the length of the power vector.

VAB VAC

VBC

VAN

VBN

IBIC

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 33

The interrupt request flag register contains bits that indicate the reason the IRQ pin has become active. The active

bit must be cleared by the host to avoid continuing firing of the interrupt by the MAXQ3180.

BIT NAME FUNCTION

15 DSPOR

When set, the DSP was unable to complete processing one cycle when another cycle was due to

begin. This indicates that the R_ADCRATE is set too low, and that samples are arriving more quickly

than they can be processed. Either increase the value of the R_ADCRATE register or set the DFUN bit

in the OPMODE2 register to disable fundamental frequency calculations to reduce the load on the DSP.

14 DSPRDY Set when the DSP cycle completes.

13 DCHR

When set, the direction of reactive energy flow has changed (that is, from capacitive to inductive or

from inductive to capacitive).

12 DCHA

When set, the direction of real energy flow has changed (that is, from toward the load to away from the

load, or from away from the load to toward the load).

11 NOZX

When set, the MAXQ3180 has failed to detect zero crossings on one or more voltage channels for the

time defined by the NZX_TIMO register.

10 UV

When set, the absolute instantaneous voltage level in one or more voltage channels failed to exceed

the trip level set in the UVLVL (Undervoltage Level) register for one DSP cycle.

9 OV

When set, the absolute instantaneous voltage level in one or more voltage channels has exceeded the

trip level set in the OVLVL (Overvoltage Level) register.

8 OC

When set, the absolute instantaneous current in one or more current channels has exceeded the trip

level set in the OCLVL (Overcurrent Level) register.

7:3 — Reserved.

2 EOVF When set, one or more energy accumulators have an MSB overflow condition.

1 CHSCH

When set, indicates a change of the CHKSUM. The CHKSUM is computed over the configuration and

calibration data. The host should review a change in CHKSUM because any change in the

configuration or calibration data affects the metering operation and accuracy.

0 PWRF

When set, a power-supply failure is imminent and the supervisory processor should begin taking steps

to save its state and prepare for a loss of power.

Global Interrupt Registers

Interrupt Request Flag Register (IRQ_FLAG) (0x004)

Bit: 15 14 13 12 11 10 9 8

Name: DSPOR DSPRDY DCHR DCHA NOZX UV OV OC

Reset: 0 0 0 0 0 0 0 0

Bit: 7 6 5 4 3 2 1 0

Name: — — — — — EOVF CHSCH PWRF

Reset: 0 0 0 0 0 0 0 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

34 ______________________________________________________________________________________

Interrupt Mask Register (IRQ_MASK) (0x006)

BIT NAME FUNCTION

15 EDSPOR When set, this flag causes the IRQ pin to become active.

14 EDSPRDY When set, this flag causes the IRQ pin to become active.

13 EDCHR

When set, this flag causes the IRQ pin to become active when the direction of reactive energy flow has

been observed to have changed (that is, from capacitive to inductive or from inductive to capacitive).

12 EDCHA

When set, this flag causes the IRQ pin to become active when the direction of real energy flow has

been observed to have changed (that is, from toward the load to away from the load, or from away from

the load to toward the load).

11 ENOZX

When set, this flag causes the IRQ pin to become active when the MAXQ3180 has failed to detect zero

crossings on one or more voltage channels for at least one DSP cycle.

10 EUV

When set, this flag causes the IRQ pin to become active when the absolute instantaneous voltage

level in one or more voltage channels failed to exceed the trip level set in the UVLVL (Undervoltage

Level) register for one DSP cycle.

9 EOV

When set, this flag causes the IRQ pin to become active when the absolute instantaneous voltage

level in one or more voltage channels has exceeded the trip level set in the OVLVL (Overvoltage Level)

8 EOC

When set, this flag causes the IRQ pin to become active when absolute instantaneous current in one

or more current channels has exceeded the trip level set in the OCLVL (Overcurrent Level) register.

7:3 — Reserved.

2 EEOVF

When set, this flag causes the IRQ pin to become active when one or more energy accumulators have

an overflow condition from their MSB.

1 ECHSCH When set, this flag enables the IRQ pin to become active when a CHKSUM change is detected.

0 EPWRF

When set, this flag causes the IRQ pin to become active when a power-supply failure is imminent and

the supervisory processor should begin taking steps to save its state and prepare for a loss of power.

Bit: 15 14 13 12 11 10 9 8

Name: EDSPOR EDSPRDY EDCHR EDCHA ENOZX EUV EOV EOC

Reset: 0 0 0 0 0 0 0 0

Bit: 7 6 5 4 3 2 1 0

Name: — — — — — EEOVF ECHSCH EPWRF

Reset: 0 0 0 0 0 0 0 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 35

Meter Pulse Configuration

Pulse Configuration—CFP Output (PLSCFG1) (0x01E)

This register selects which phases are included in the CFP pulse output and also selects which quantity is accumu-

lated to drive the pulse output.

Bit: 7 6 5 4 3 2 1 0

Name: QNSEL PHASEC PHASEB PHASEA

Reset: 0x0 0 0 0

BIT NAME FUNCTION

7:3 QNSEL

CFP Pulse Output Source Select. This five-bit field determines what meter value will be accumulated in

each of the phases to produce the CFP pulse output. All other values are reserved.

00000 = Net real energy

00001 = Absolute real energy

00010 = Net reactive energy

00011 = Absolute reactive energy

00100 = Apparent energy

00110 = IRMS

00111 = VRMS

01000 = Real energy delivered to load

01001 = Real energy delivered to line

01010 = Reactive energy, quadrant I

01011 = Reactive energy, quadrant II

01100 = Reactive energy, quadrant III

01101 = Reactive energy, quadrant IV

2 PHASEC CFP Phase C Inclusion. When this bit is set, phase C is included in CFP pulse generation.

1 PHASEB CFP Phase B Inclusion. When this bit is set, phase B is included in CFP pulse generation.

0 PHASEA CFP Phase A Inclusion. When this bit is set, phase A is included in CFP pulse generation.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

36 ______________________________________________________________________________________

Pulse Configuration—CFQ Output (PLSCFG2) (0x01F)

This register selects which phases are included in the CFQ pulse output and also selects which quantity is accumu-

lated to drive the pulse output.

BIT NAME FUNCTION

7:3 QNSEL

CFQ Pulse Output Source Select. This five-bit field determines what meter value is accumulated in

each of the phases to produce the CFQ pulse output. All other values are reserved.

00000 = Net real energy

00001 = Absolute real energy

00010 = Net reactive energy

00011 = Absolute reactive energy

00100 = Apparent energy

00110 = IRMS

00111 = VRMS

01000 = Real energy delivered to load

01001 = Real energy delivered to line

01010 = Reactive energy, quadrant I

01011 = Reactive energy, quadrant II

01100 = Reactive energy, quadrant III

01101 = Reactive energy, quadrant IV

2 PHASEC CFQ Phase C Inclusion. When this bit is set, phase C is included in CFQ pulse generation.

1 PHASEB CFQ Phase B Inclusion. When this bit is set, phase B is included in CFQ pulse generation.

0 PHASEA CFQ Phase A Inclusion. When this bit is set, phase A is included in CFQ pulse generation.

Bit: 7 6 5 4 3 2 1 0

Name: QNSEL PHASEC PHASEB PHASEA

Reset: 0x0 0 0 0

CFP Pulse Width (PLS1_WD) (0x020)

This register designates the width of the CFP pulse, that is, the duration of the period that the CFP pulse is in the

active state. This value is given in ADC frame times (about 320μs). The default value of 0x9C (156 decimal) provides

a pulse width of about 50ms.

Bit: 15 14 13 12 11 10 9 8

Name: CFP Pulse-Width High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: CFP Pulse-Width Low Byte

Reset: 0x9C

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 37

CFP Pulse Threshold (THR1) (0x022)

This register designates the threshold of the CFP pulse. This value is used to set the meter constant for the CFP

pulse output. When the CFP pulse accumulator exceeds the value set in this register, the CFP pulse output is activat-

ed and the CFP pulse accumulator is reduced by the amount in this register.

CFQ Pulse Width (PLS2_WD) (0x026)

This register designates the width of the CFQ pulse; that is, the duration of the period that the CFQ pulse is in the

active state. This value is given in ADC frame times (about 320μs). The default value of 0x9C (156 decimal) provides

a pulse width of about 50ms.

Bit: 31 30 29 28 27 26 25 24

Name: THR1 Byte 3

Reset: 0x00

Bit: 23 22 21 20 19 18 17 16

Name: THR1 Byte 2

Reset: 0x10

Bit: 15 14 13 12 11 10 9 8

Name: THR1 Byte 1

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: THR1 Byte 0

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: CFQ Pulse-Width High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: CFQ Pulse-Width Low Byte

Reset: 0x9C

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

38 ______________________________________________________________________________________

CFQ Pulse Threshold (THR2) (0x028)

This register designates the threshold of the CFQ pulse. This value is used to set the meter constant for the CFQ

pulse output. When the CFQ pulse accumulator exceeds the value set in this register, the CFQ pulse output is acti-

vated and the CFQ pulse accumulator is reduced by the amount in this register.

Calibration Registers

Current Gain, Phase X = A/B/C/N (X.I_GAIN) (A: 0x130, B: 0x21C, C: 0x308, N: 0x12E)

This register contains gain coefficient for phase X current channel. The raw values are taken from the selected mea-

surement quantity and scaled by the factor:

Note: Bit 15 of this register must be set to zero for correct operation.

XI GAIN._

214

Bit: 31 30 29 28 27 26 25 24

Name: THR2 Byte 3

Reset: 0x00

Bit: 23 22 21 20 19 18 17 16

Name: THR2 Byte 2

Reset: 0x10

Bit: 15 14 13 12 11 10 9 8

Name: THR2 Byte 1

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: THR2 Byte 0

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: Current Gain Coefficient High Byte

Reset: 0x40

Bit: 7 6 5 4 3 2 1 0

Name: Current Gain Coefficient Low Byte

Reset: 0x00

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 39

Voltage Gain, Phase X = A/B/C (X.V_GAIN) (A: 0x132, B: 0x21E, C: 0x30A)

This register contains gain coefficient for phase X voltage channel. The raw values are taken from the selected mea-

surement quantity and scaled by the factor:

Note: Bit 15 of this register must be set to zero for correct operation.

Energy Gain, Phase X = A/B/C (X.E_GAIN) (A: 0x134, B: 0x220, C: 0x30C)

This register contains gain coefficient for phase X energy. The raw values are taken from the selected measurement

quantity and scaled by the factor:

Note: Bit 15 of this register must be set to zero for correct operation.

Phase-Angle Compensation, High Range, Phase X = A/B/C (X.PA0)

(A: 0x13E, B: 0x22A, C: 0x316)

This signed register contains the angle as a fraction of one radian to add to the measured phase angle when the

measured current is above the value given in I1THR. This signed value ranges from -0.5 radian (at a value of

0x8000) to +(0.5 - 2-16) radian (at a value of 0x7FFF).

XE GAIN._

214

X V GAIN._

214

Bit: 15 14 13 12 11 10 9 8

Name: Voltage Gain Coefficient High Byte

Reset: 0x40

Bit: 7 6 5 4 3 2 1 0

Name: Voltage Gain Coefficient Low Byte

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: Energy Gain Coefficient High Byte

Reset: 0x40

Bit: 7 6 5 4 3 2 1 0

Name: Energy Gain Coefficient Low Byte

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: Phase-Angle Offset High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Phase-Angle Offset Low Byte

Reset: 0x00

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

40 ______________________________________________________________________________________

Phase-Angle Compensation, Medium Range, Phase X = A/B/C (X.PA1)

(A: 0x140, B: 0x22C, C: 0x318)

This signed register contains the angle, as a fraction of one radian, to add to the measured phase angle when the

measured current is between the values given in I1THR and I2THR. This signed value ranges from -0.5 radian (at a

value of 0x8000) to +(0.5 - 2-16) radian (at a value of 0x7FFF).

Phase-Angle Compensation, Low Range, Phase X = A/B/C (X.PA2)

(A: 0x142, B: 0x22E, C: 0x31A)

This signed register contains the angle, as a fraction of one radian, to add to the measured phase angle when the

measured current is below the value given in I2THR. This signed value ranges from -0.5 radian (at a value of 0x8000)

to +(0.5 - 2-16) radian (at a value of 0x7FFF).

Limit Registers

Overcurrent Level (OCLVL) (0x044)

This register specifies the fraction of full-scale current that is declared to be an overcurrent condition. When X.IRMS

exceeds this level for one DSP cycle, the OCF flag in the X.FLAGS register is set. If the OCM flag is set in the

X.MASK register, setting the OCF flag will cause the interrupt bit OC to be set in the IRQ_FLAG register. If the inter-

rupt is enabled, the interrupt pin is driven active. Full scale is represented by 0x10000. The maximum value for this

Bit: 15 14 13 12 11 10 9 8

Name: Phase-Angle Offset High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Phase-Angle Offset Low Byte

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: Phase-Angle Offset High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Phase-Angle Offset Low Byte

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: Overcurrent Level High Byte

Reset: 0xFF

Bit: 7 6 5 4 3 2 1 0

Name: Overcurrent Level Low Byte

Reset: 0xFF

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 41

Overvoltage Level (OVLVL) (0x046)

This register specifies the fraction of full-scale voltage that is declared to be an overvoltage condition. When X.VRMS

exceeds this level for one DSP cycle, the OVF flag in the X.FLAGS register is set. If the OVM flag is set in the

X.MASK register, setting the OVF flag will cause the interrupt bit OV to be set in the IRQ_FLAG register. If the inter-

rupt is enabled, the interrupt pin is driven active. Full scale is represented by 0x10000. The maximum value for this

Undervoltage Level (UVLVL) (0x048)

This register specifies the fraction of full-scale voltage below which an undervoltage condition is declared. When

X.VRMS falls below this level for one DSP cycle, the UVF flag in the X.FLAGS register is set. If the UVM flag is set in

the X.MASK register, setting the UVF flag will cause the interrupt bit UV to be set in the IRQ_FLAG register. If the

interrupt is enabled, the interrupt pin is driven active. Full scale is represented by 0x10000. The maximum value for

this register is 0xFFFF.

No-Load Level (NOLOAD) (0x04A)

This register specifies the fraction of full-scale current below which a no-load condition is declared. When X.IRMS

falls below this level, the MAXQ3180 no longer accumulates power for phase X. Full scale is represented by

0x10000. The maximum value for this register is 0xFFFF.

Bit: 15 14 13 12 11 10 9 8

Name: Overvoltage Level High Byte

Reset: 0xFF

Bit: 7 6 5 4 3 2 1 0

Name: Overvoltage Level Low Byte

Reset: 0xFF

Bit: 15 14 13 12 11 10 9 8

Name: Undervoltage Level High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Undervoltage Level Low Byte

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: No-Load Level High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: No-Load Level Low Byte

Reset: 0x03

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

42 ______________________________________________________________________________________

Phase Status Registers

Interrupt Flags, Phase X = A/B/C (X.FLAGS) (A: 0x144, B: 0x230, C: 0x31C)

The X.FLAGS register contains condition flags that relate to the function of phase X (A/B/C) measurements. Once

set, these bits can be cleared only by the host.

Bit: 7 6 5 4 3 2 1 0

Name: — — DCHRF DCHAF NOZXF UVF OVF OCF

Reset: 0 0 0 0 0 0 0 0

BIT NAME FUNCTION

7:6 — Reserved.

5 DCHRF

Reactive Energy Direction Change. Set when the direction of reactive power flow changes (from

capacitive to inductive or from inductive to capacitive). If the DCHRM bit is set, this bit sets the DCHR

flag in the IRQ_FLAG register.

4 DCHAF

Real Energy Direction Change. Set when the direction of real power flow changes (from toward the load

to toward the line, or from toward the line to toward the load). If the DCHAM bit is set, this bit sets the

DCHA flag in the IRQ_FLAG register.

3 NOZXF

No-Zero Crossing. Set when the voltage waveform in phase X fails to exhibit a zero crossing during

NZX_TIMO of the ADC sample periods. If the NOZXM bit is set, this bit sets the NOZX flag in the

IRQ_FLAG register.

2 UVF

Undervoltage. Set when the RMS voltage in phase X falls below the undervoltage threshold set in

UVLVL. If the UVM bit is set, this bit sets the UV flag in the IRQ_FLAG register.

1 OVF

Overvoltage. Set when the RMS voltage in phase X exceeds the overvoltage threshold set in OVLVL. If

the OVM bit is set, this bit sets the OV flag in the IRQ_FLAG register.

0 OCF

Overcurrent. Set when the RMS current in phase X exceeds the overcurrent threshold set in OCLVL. If

the OCM bit is set, this bit sets the OC flag in the IRQ_FLAG register.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 43

Interrupt Mask, Phase X = A/B/C (X.MASK) (A: 0x145, B: 0x231, C: 0x31D)

Energy Overflow Flags, Phase X = A/B/C (X.EOVER) (A: 0x146, B: 0x232, C: 0x31E)

These bits indicate that an overflow condition has occurred on an energy accumulator. An overflow condition is not

an error condition. Rather, it simply indicates that the value in the energy accumulator could be smaller than the pre-

vious reading due to the overflow in the counter. To obtain the actual energy usage since the previous reading,

0x100000000 must be added to the difference. These bits, once set, can be cleared only by the host.

Bit: 7 6 5 4 3 2 1 0

Name: DIR_R DIR_A DCHRM DCHAM NOZXM UVM OVM OCM

Reset: 0 0 0 0 0 0 0 0

BIT NAME FUNCTION

7 DIR_R

Reactive Energy Direction Status

0 = positive

1 = negative

6 DIR_A

Active Energy Direction Status

0 = positive

1 = negative

5 DCHRM

Reactive Energy Direction Change Mask. If set, a change in reactive power direction on phase X

causes the DCHR flag in the IRQ_FLAG register to be set.

4 DCHAM

Real Energy Direction Change Mask. If set, a change in real power direction on phase X causes the

DCHA flag in the IRQ_FLAG register to be set.

3 NOZXM

No-Zero Crossing Mask. If set, a no-zero crossing on phase X causes the NOZX flag in the IRQ_FLAG

2 UVM

Undervoltage Mask. If set, an undervoltage condition on phase X causes the UV flag in the IRQ_FLAG

1 OVM

Overvoltage Mask. If set, an overvoltage condition on phase X causes the OV flag in the IRQ_FLAG

0 OCM

Overcurrent Mask. If set, an overcurrent condition on phase X causes the OC flag in the IRQ_FLAG

BIT NAME FUNCTION

7:5 — Reserved.

4 SOV When set, indicates an overflow condition on the apparent energy accumulator.

3 RNOV When set, indicates an overflow condition on the reactive negative energy accumulator.

2 RPOV When set, indicates an overflow condition on the reactive positive energy accumulator.

1 ANOV When set, indicates an overflow condition on the real negative energy accumulator.

0 APOV When set, indicates an overflow condition on the real positive energy accumulator.

Bit: 7 6 5 4 3 2 1 0

Name: — — — SOV RNOV RPOV ANOV APOV

Reset: 0 0 0 0 0 0 0 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

44 ______________________________________________________________________________________

Measurements

Line Frequency (LINEFR) (0x062)

Line frequency, LSB = 0.001Hz.

Power Factor, Phase X = A/B/C (X.PF) (A: 0x1C6, B: 0x2B2, C: 0x39E)

Power factor of phase A/B/C, LSB = 1/214. Note that the power factors are signed integers, and a negative value

indicates a reversed power flow direction.

RMS Voltage, Phase X = A/B/C (X.VRMS) (A: 0x1C8, B: 0x2B4, C: 0x3A0)

This register provides the raw RMS voltage over the most recent DSP cycle, LSB = VFS/224.

Bit: 15 14 13 12 11 10 9 8

Name: Line Frequency High Byte

Reset:

Bit: 7 6 5 4 3 2 1 0

Name: Line Frequency Low Byte

Reset:

Bit: 15 14 13 12 11 10 9 8

Name: Power Factor High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Power Factor Low Byte

Reset: 0x00

Bit: 31 30 29 28 27 26 25 24

Name: RMS Voltage Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: RMS Voltage Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: RMS Voltage Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: RMS Voltage Byte 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 45

RMS Current, Phase X = A/B/C (X.IRMS) (A: 0x1CC, B: 0x2B8, C: 0x3A4)

This register provides the raw RMS current over the most recent DSP cycle, LSB = IFS/224.

Energy, Real Positive, Phase X = A/B/C (X.EAPOS)

(A: 0x1E8, B: 0x2D4, C: 0x3C0)

On every DSP cycle, the contents of the X.ACT register are tested, and, if positive, are added to this register. When

this register overflows, the APOV bit in the X.EOVER register is set.

Bit: 31 30 29 28 27 26 25 24

Name: RMS Current Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: RMS Current Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: RMS Current Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: RMS Current Byte 0

Bit: 31 30 29 28 27 26 25 24

Name: Real Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Real Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Real Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Real Energy Byte 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

46 ______________________________________________________________________________________

Energy, Real Negative, Phase X = A/B/C (X.EANEG)

(A: 0x1EC, B: 0x2D8, C: 0x3C4)

On every DSP cycle, the contents of the X.ACT register are tested, and, if negative, absolute values are added to

this register. When this register overflows, the ANOV bit in the X.EOVER register is set.

Energy, Reactive Positive, Phase X = A/B/C (X.ERPOS)

(A: 0x1F0, B: 0x2DC, C: 0x3C8)

On every DSP cycle, the contents of the X.REA register are tested, and, if positive, are added to this register. When

this register overflows, the RPOV bit in the X.EOVER register is set.

Bit: 31 30 29 28 27 26 25 24

Name: Real Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Real Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Real Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Real Energy Byte 0

Bit: 31 30 29 28 27 26 25 24

Name: Reactive Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Reactive Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Reactive Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Reactive Energy Byte 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 47

Energy, Reactive Negative, Phase X = A/B/C (X.ERNEG)

(A: 0x1F4, B: 0x2E0, C: 0x3CC)

On every DSP cycle, the contents of the X.REA register are tested, and, if negative, absolute values are added to

this register. When this register overflows, the RNOV bit in the X.EOVER register is set.

Energy, Apparent, Phase X = A/B/C (X.ES) (A: 0x1F8, B: 0x2E4, C: 0x3D0)

On every DSP cycle, the contents of the X.APP register are added to this register. When this register overflows, the

SOV bit in the X.EOVER register is set.

Bit: 31 30 29 28 27 26 25 24

Name: Reactive Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Reactive Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Reactive Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Reactive Energy Byte 0

Bit: 31 30 29 28 27 26 25 24

Name: Apparent Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Apparent Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Apparent Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Apparent Energy Byte 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

48 ______________________________________________________________________________________

Virtual Register Conversion Coefficients

Voltage Units Conversion Coefficient (VOLT_CC) (0x014)

This register contains the value by which the raw voltage value in each phase (A.VRMS, B.VRMS, and C.VRMS) is

multiplied before being presented to the virtual RMS voltage registers (V.A, V.B, and V.C).

To determine the value of VOLT_CC, a voltage value for the least significant bit (VOLT_LSB) of the V.X registers must

be selected. Typical values might range from 1mV to 1nV. To avoid significant conversion loss, VOLT_LSB should be

chosen such that VOLT_CC is >1000. Once VOLT_LSB is determined, calculate VOLT_CC from the following equa-

tion:

Current Units Conversion Coefficient (AMP_CC) (0x016)

This register contains the value by which the raw current value in each phase (A.IRMS, B.IRMS, C.IRMS, and

N.IRMS) is multiplied before being presented to the virtual RMS current registers (I.A, I.B, I.C, and I.N). To determine

the value of AMP_CC, a current value for the least significant bit (AMP_LSB) of the I.X registers must be selected.

Typical values might range from 1nA to 10μA. To avoid significant conversion loss, AMP_LSB should be chosen

such that AMP_CC is >1000. Once determined, calculate AMP_CC from the following equation:

AMP CC I

AMP LSB

=×224

VOLT CC V

VOLT LSB

=×224

Bit: 15 14 13 12 11 10 9 8

Name: Voltage Units Conversion Coefficient High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Voltage Units Conversion Coefficient Low Byte

Reset: 0x01

Bit: 15 14 13 12 11 10 9 8

Name: Current Units Conversion Coefficient High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Current Units Conversion Coefficient Low Byte

Reset 0x01

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 49

Power Units Conversion Coefficient (PWR_CC) (0x018)

This register contains the value by which the raw power value in each phase is multiplied before being presented to

the virtual power registers. The table below lists the raw power registers and the corresponding virtual registers.

PWR_CC establishes the amount of power represented by one PWR_LSB of the power registers. To avoid significant

conversion loss, PWR_LSB should be chosen such that PWR_CC is > 1000. Calculate the value of PWR_CC accord-

ing to the following formula:

PWR CC IV

PWR LSB

FS FS

=×

×232

Bit: 15 14 13 12 11 10 9 8

Name: Power Units Conversion Coefficient High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Power Units Conversion Coefficient Low Byte

Reset: 0x01

DESCRIPTION RAW VIRTUAL

Real power, phase A A.ACT PWRP.A

Real power, phase B B.ACT PWRP.B

Real power, phase C C.ACT PWRP.C

Real power, total — PWRP.T

Reactive power, phase A A.REA PWRQ.A

Reactive power, phase B B.REA PWRQ.B

Reactive power, phase C C.REA PWRQ.C

Reactive power, total — PWRQ.T

Apparent power, phase A A.APP PWRS.A

Apparent power, phase B B.APP PWRS.B

Apparent power, phase C C.APP PWRS.C

Apparent power, total — PWRS.T

Real power, phase A, fundamental frequency only A.ACTF PWRPF.A

Real power, phase B, fundamental frequency only B.ACTF PWRPF.B

Real power, phase C, fundamental frequency only C.ACTF PWRPF.C

Real power, total, fundamental frequency only — PWRPF.T

Reactive power, phase A, fundamental frequency only A.REAF PWRQF.A

Reactive power, phase B, fundamental frequency only B.REAF PWRQF.B

Reactive power, phase C, fundamental frequency only C.REAF PWRQF.C

Reactive power, total, fundamental frequency only — PWRQF.T

Apparent power, phase A, fundamental frequency only A.APPF PWRSF.A

Apparent power, phase B, fundamental frequency only B.APPF PWRSF.B

Apparent power, phase C, fundamental frequency only C.APPF PWRSF.C

Apparent power, total, fundamental frequency only — PWRSF.T

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

50 ______________________________________________________________________________________

Energy Units Conversion Coefficient (ENR_CC) (0x01A)

This register contains the value by which the raw accumulated energy value in each phase is multiplied before being

presented to the virtual energy registers. The table below lists the raw energy accumulators and the corresponding

virtual registers.

Bit: 15 14 13 12 11 10 9 8

Name: Energy Units Conversion Coefficient High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Energy Units Conversion Coefficient Low Byte

Reset: 0x01

DESCRIPTION RAW VIRTUAL

Real energy, phase A, positive direction A.EAPOS

Real energy, phase A, reverse direction A.EANEG ENRP.A*

Real energy, phase B, positive direction B.EAPOS

Real energy, phase B, reverse direction B.EANEG ENRP.B*

Real energy, phase C, positive direction C.EAPOS

Real energy, phase C, reverse direction C.EANEG ENRP.C*

Real energy, total — ENRP.T

Reactive energy, phase A, positive direction A.ERPOS

Reactive energy, phase A, reverse direction A.ERNEG ENRQ.A*

Reactive energy, phase B, positive direction B.ERPOS

Reactive energy, phase B, reverse direction B.ERNEG ENRQ.B*

Reactive energy, phase C, positive direction C.ERPOS

Reactive energy, phase C, reverse direction C.ERNEG ENRQ.C*

Reactive energy, total — ENRQ.T

Apparent energy, phase A A.ES ENRS.A

Apparent energy, phase B B.ES ENRS.B

Apparent energy, phase C C.ES ENRS.C

Apparent energy, total — ENRS.T

Real energy, phase A, positive direction, fundamental only A.EAFPOS

Real energy, phase A, reverse direction, fundamental only A.EAFNEG ENRPF.A*

Real energy, phase B, positive direction, fundamental only B.EAFPOS

Real energy, phase B, reverse direction, fundamental only B.EAFNEG ENRPF.B*

Real energy, phase C, positive direction, fundamental only C.EAFPOS

Real energy, phase C, reverse direction, fundamental only C.EAFNEG ENRPF.C*

Real energy, total, fundamental only — ENRPF.T

Reactive energy, phase A, positive direction, fundamental only A.ERFPOS

Reactive energy, phase A, reverse direction, fundamental only A.ERFNEG ENRQF.A*

Reactive energy, phase B, positive direction, fundamental only B.ERFPOS

Reactive energy, phase B, reverse direction, fundamental only B.ERFNEG ENRQF.B*

These registers represent the algebraic sum of the positive and reverse energy in the two “raw” registers noted. Thus, the energy

returned in these virtual registers represents the net energy.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 51

Energy Units Conversion Coefficient (ENR_CC) (0x01A) (continued)

DESCRIPTION RAW VIRTUAL

Reactive energy, phase C, positive direction, fundamental only C.ERFPOS

Reactive energy, phase C, reverse direction, fundamental only C.ERFNEG ENRQF.C*

Reactive energy, total, fundamental only — ENRQF.T

Apparent energy, phase A, fundamental only A.ESF ENRSF.A

Apparent energy, phase B, fundamental only B.ESF ENRSF.B

Apparent energy, phase C, fundamental only C.ESF ENRSF.C

Apparent energy, total, fundamental only — ENRSF.T

To avoid significant conversion loss, ENR_LSB should be chosen such that ENR_CC is > 1000. Calculate the value

of ENR_CC according to the following formula:

Virtual Registers

The virtual registers are calculated values derived from one or more real registers. They are calculated at the time

they are requested, and thus could involve additional time to return a value. Most virtual registers are 8 bytes in

length and are delivered least significant byte first.

Power

Real Power, Phase X = A/B/C/T (PWRP.X) (A: 0x801, B: 0x802, C: 0x804, T: 0x807)

This signed register contains the real instantaneous power delivered into phase A/B/C or total. Power is calculated

from the instantaneous energy measurement according to the following equation:

The register is 8 bytes long, but the most significant 2 bytes are not used. See the PWR_CC register description for

more details.

Note that the sign bit is bit 47 for all 8-byte signed virtual registers.

PWRP X XACT PWR CC

.._

=××216

ENR CC IVt

ENR LSB

FS FS FR

=××

×216

These registers represent the algebraic sum of the positive and reverse energy in the two “raw” registers noted. Thus, the energy

accumulated in these virtual registers represents the net energy.

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

52 ______________________________________________________________________________________

Reactive Power, Phase X = A/B/C/T (PWRQ.X) (A: 0x811, B: 0x812, C: 0x814, T: 0x817)

This signed register contains the reactive instantaneous power delivered into phase A/B/C or total. Power is calculat-

ed from the instantaneous energy measurement according to the following equation:

The register is 8 bytes long, but the most signficant 2 bytes are not used. See the PWR_CC register description for

more details.

Apparent Power, Phase X = A/B/C/T (PWRS.X) (A: 0x821, B: 0x822, C: 0x824, T: 0x827)

This register contains the apparent instantaneous power delivered into phase A/B/C or total. Power is calculated

from the instantaneous energy measurement according to the following equation:

The register is 8 bytes long, but the most significant 2 bytes are not used. See the PWR_CC register description for

more details.

PWRS X X APP PWR CC

.._

=××216

PWRQ X X REA PWR CC

.._

=××216

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 53

Voltage and Current

RMS Volts, Phase X = A/B/C (V.X) (A: 0x831, B: 0x832, C: 0x834)

This register contains the RMS voltage on phase A/B/C. The units are defined by the VOLT_CC setting such that V.X

= X.VRMS x VOLT_CC. In this equation, VOLT_CC is the conversion coefficient. See the VOLT_CC register for more

information.

RMS Amps, Phase X = A/B/C/N (I.X) (A: 0x841, B: 0x842, C: 0x844, N: 0x840)

This register contains the RMS current on phase A/B/C or the neutral channel. The units are defined by the AMP_CC

setting such that I.X = X.IRMS x AMP_CC. In this equation, AMP_CC is the conversion coefficient. See the AMP_CC

Power Factor

Power Factor (PF.T) (0x867)

This signed register contains the power factor of the total power. The power factor is calculated as:

It is expressed in units of 0.00001; thus, unity power factor is expressed as decimal 100,000

(0x00000000000186A0). This register is presented as a two’s complement value, so that a load delivering real power

to the line (that is, reverse power) is seen as having a power factor of -1 (0x0000FFFFFFFE7960).

PF T A ACT B ACT C ACT

A APP B APP C APP

....

...

=++

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

54 ______________________________________________________________________________________

Energy

Real Energy, Phase A/B/C/T (ENRP.X) (A: 0x8C1, B: 0x8C2, C: 0x8C4, T: 0x8C7)

This signed register contains the real accumulated energy delivered into phase A/B/C or total. The register is calcu-

lated according to the following formula:

ENRP.X = ENR_CC x (X.EAPOS - X.EANEG)

Reactive Energy, Phase A/B/C/T (ENRQ.X) (A: 0x8D1, B: 0x8D2, C: 0x8D4, T: 0x8D7)

This signed register contains the reactive accumulated energy delivered into phase A/B/C or total. The register is

calculated according to the following formula:

ENRQ.X = ENR_CC x (X.ERPOS - X.ERNEG)

Apparent Energy, Phase A/B/C/T (ENRS.X) (A: 0x871, B: 0x872, C: 0x874, T: 0x877)

This register contains the apparent accumulated energy delivered into phase A/B/C or total. The register is the prod-

uct of the ENR_CC and X.ES registers.

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 55

Theory of Operation

Analog Front-End Operation

Whenever the MAXQ3180 is in one of the active operat-

ing modes (Run Mode or LOWPM Mode), the analog

front-end operates continuously, scanning up to eight

scan slots depending on the selected front-end config-

uration. For each analog scan slot that is enabled, one

of the eight differential input pairs is measured.

The SCAN_IX and SCAN_VX (X = A/B/C), SCAN_IN,

and SCAN_TE registers contain the settings for each

slot, which include whether the slot is enabled and the

differential input pair to measure during that scan slot.

The logical mapping of the slots is fixed in following

order:

• Slot 0—Phase A Current (IA)

• Slot 1—Phase A Voltage (VA)

• Slot 2—Phase C Current (IC)

• Slot 3—Phase C Voltage (VC)

• Slot 4—Phase B Current (IB)

• Slot 5—Phase B Voltage (VB)

• Slot 6—Neutral Current (IN)—disabled by default

• Slot 7—Temperature Measurement—disabled by

default

The required time for each analog scan slot measure-

ment (tC) is determined by the MAXQ3180 system

clock frequency and the setting of the R_ADCRATE

hardware register, as shown below:

tC= 1/fCLK x (R_ADCRATE[8:0] + 1)

Using the default register settings (R_ADCRATE = 13Fh

= 319d), the time for each analog slot measurement

(tC) is 40μs when the MAXQ3180 is running at 8MHz.

Since there are eight analog scan slots in the measure-

ment frame, the total time for all measurements (tFR) is

tCx 8. Using the default settings with the MAXQ3180

running at 8MHz, the entire sequence of measurements

takes 320μs to complete, which, in turn, means that

320μs will elapse, for example, between one phase A

current measurement and the next.

Even if some of the analog measurement slots (such as

neutral current or temperature measurement) are

skipped by setting the DADCNV bit in that slot’s regis-

ter to 1, the time period for that slot will remain in the

frame, ensuring that the total frame time is always tCx

8, regardless of which individual slots are enabled or

disabled.

Digital Signal Processing (DSP)

Terminology

Establishing the precise definitions of some of the terms

used in this document will assist in understanding how

the DSP functions.

Sample Period: The amount of time required to mea-

sure a single data element; 40μs, by default.

ADC Frame Period: The amount of time required for

the ADC to sample all analog inputs; always equal to 8

sample periods. The inverse of this value is the

frame

rate

; by default 3125 samples per second. This is the

rate at which any particular signal is sampled by the

MAXQ3180.

Line Cycle: The period of time from one positive-going

zero crossing on a voltage channel to the next positive-

going zero crossing. At 50Hz, this is nominally 20ms; at

60Hz, this is nominally 16.67ms.

Cycle Count: The number of line cycles contained in a

single DSP cycle. An integer, this is typically set to

some value greater than one to minimize the effect of

load variations that may not occur in every line cycle.

By default, this value is 16.

DSP Cycle: The period of time over which line parame-

ters are calculated. Energy and other parameters are

accumulated once per DSP cycle. One DSP cycle is

the time of a line cycle multiplied by the cycle count.

NS: This value represents the number of ADC frame

periods in a DSP cycle. This is a noninteger calculated

value. For example, if the cycle count is set to unity,

and the line frequency is exactly 50Hz, the NS value

would be 20ms/320μs = 62.5.

Digital Processing

As voltage and current samples are collected, the

MAXQ3180 performs a variety of digital filtering,

accumulation, and processing calculations to arrive at

meter-reading values (such as line frequency, RMS

voltage and current, and active and reactive power)

that can then be read by the master. The MAXQ3180

calculates and detects values and conditions including

the following:

• Zero-crossing detection

• Line frequency and line period calculation

• RMS voltage (phase A, phase B, phase C)

• RMS current (phase A, phase B, phase C, neutral

current)

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

56 ______________________________________________________________________________________

• Power (active, reactive, and apparent) for each

phase

• Energy accumulation (including energy pulse output

function)

• Overvoltage detection

• Overcurrent detection

• Undervoltage detection

Per Sample Operations

On every ADC frame, the input samples are processed

as follows:

• The voltage and current samples are read. The cur-

rent sample is shifted to account for the gain applied

in the PGA. The phase- and gain-corrected samples

are passed to the next stage.

• Both the current and voltage signals are passed

through highpass filters (HPF) specified by the

HPF_C variable.

• The current and voltage signals are now split into

several components. The first of these components is

squared and accumulated to begin the RMS current

and voltage process. The second is processed and

accumulated to begin the real/reactive power calcu-

lation. And a third is processed through a peak filter

(specified by B0FUND and A1FUND registers) and

then accumulated to provide information for the fun-

damental frequency power calculations.

The result is a set of accumulated values that represent

squared voltage, squared current, and real (active) and

reactive (P and Q) energies for both the entire usable

spectrum and as filtered by the peak filter. The real and

imaginary components of energy at this point do not yet

represent real and reactive power; to obtain usable

power values further processing is required. Each of

these values is further processed at the end of each

DSP cycle.

Per DSP Cycle Operations

At the end of each DSP cycle, accumulated information

is available that is used to calculate all other opera-

tional results in the meter. DSP cycles track the line fre-

quency and have a duration of the number of cycles

specified in the CYCNT register. On each phase, the

time required for CYCNT cycles to complete is calculat-

ed and this value is used to update the duration of one

DSP cycle, specified in the NS register.

NS contains the number of ADC frame periods in a sin-

gle DSP cycle. Because line frequency varies slightly

from cycle to cycle, and because the ADC frame clock

is not synchronized to the line, the value of NS is not an

integer, and varies slightly from DSP cycle to DSP cycle.

Because the value of NS is so critical to accurate calcu-

lation of energy, ensuring that it is correct on every

cycle is essential. There are two ways to manage the

slight variation of NS from cycle to cycle: first, one

could simply replace the old value of NS with the newly

calculated value on each DSP cycle. This means that

NS (and every other value in the meter, since they

depend on NS) would have a significant amount of

uncertainty. A better method is to use each newly cal-

culated value of NS as an input to a filter. The

output

the filter is then the value of NS that is actually used in

calculations. In the MAXQ3180, this filter is controlled

by the AVG_NS register.

CURRENT INPUT ADC

HPF

BPF

ENERGY PROCESSING

EPF

EQF

ENERGY PROCESSING

VOLTAGE INPUT

HPF

GAIN SEL I_GAIN

V_GAIN

ADC

Figure 9. Per Sample Operations

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 57

A second problem with updating NS on every line

cycles is the fact that noise impulses that occur at near-

ly the same time as the zero crossing can shift the zero

crossing, affecting the accuracy of the energy mea-

sured during the preceding period. For this reason, a

second register, REJ_NS contains a value that specifies

how far a particular sample can deviate from the aver-

age and still be considered valid. If the period of the

newly acquired DSP cycle differs from the previously

accumulated average value by more than REJ_NS ADC

frames, NS is not updated with the new period (but the

energy is still accumulated).

With this discussion in mind, the signal path for the vari-

ous reported parameters can be reviewed.

RMS Volts and RMS Amps: First, the squared voltage

accumulation is divided by NS. This accomplishes the

“mean” part of the “root-mean-square” calculation.

Then, the square root of the result is taken, producing

the raw RMS calculation value.

On the voltage channel, the signal is ready for gain

compensation to be applied. But on the current channel,

there is an additional twist: depending on the amplitude

of the current, there may be a gain factor pre-applied

before the raw sample is available. To compensate for

inaccuracy in the gain factor for the amplifier and for

noise seen in the channel at high gain settings, it may

be necessary to provide linearity compensation.

There are three registers that manage the linearization

of the current signal: the X.OFFS_HI (X = A/B/C) regis-

ter contains a signed value that is added to the raw

RMS current signal before further processing; the

X.OFFS_LO register contains a signed value that is

added to the raw RMS current signal when the current

signal is below a low current threshold (1/32 of the full

scale) value; and the X.GAIN_LO register contains a

gain adjustment that is applied to the current signal

when the current signal is below the threshold value.

The practical effect of this is to turn what may be a

somewhat nonlinear response curve for the current sen-

sor to a much more linear response by two-piece

approximation.

The “high current” calibration term X.OFFS_HI is used

so long as the instantaneous current exceeds the low-

current threshold at some instant during a DSP cycle. As

long as this threshold is crossed during a DSP cycle, the

value in X.OFFS_HI controls the offset current.

When the input stays below the low-current threshold

for one DSP cycle, the X.OFFS_LO and X.GAIN_LO are

applied. The low-current calibration terms (X.GAIN_LO

and X.OFFS_LO) remain in effect until the peak of input

current waveform exceeds 1/32 of full-scale current at

any time during a DSP cycle.

As a final step, both voltage and current are passed

through an averaging filter that provides smoothing for

the signals. The amount of filtering is given in AVG_C.

Energy: The per-sample processing produces a pair of

digital signals that represent the complex energy sig-

nal. From this complex signal, it is desired to extract the

real portion and the reactive portion. At first glance, this

seems trivial: the real portion is the real part of the com-

plex signal, and the reactive portion is the imaginary

part of the complex signal. Apparent power (in volt-

amperes) is the magnitude of the complex signal, and

power angle is the argument of the complex signal.

LINEARIZATION AVERAGE

AVG_C

IRMS

OFFS_HI

GAIN_LO

OFFS_LO

RAW_I

AVERAGE

AVG_C

VRMS

RAW_V

Figure 10. Computation of RMS Values

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

58 ______________________________________________________________________________________

But current sensors and other external circuitry compo-

nents introduce a phase distortion to the current signal,

and this phase distortion may not be constant at all cur-

rent values. Consequently, for the most precise mea-

surements, the phase between the voltage and current

signals must be compensated. In the MAXQ3180, the

energy signals are compensated for phase offset by

performing a complex multiplication of the signal with

the contents of the appropriate phase offset register.

Determining which phase offset register is appropriate is

a matter of comparing the incoming RMS current for the

phase with the contents of the I1THR and I2THR regis-

ters. It is the responsibility of the administrative software

to ensure that I1THR is greater than or equal to I2THR. If

the raw RMS current is greater than or equal to the con-

tents of I1THR, then the angle expressed in PA0 is used

to compensate the phase angle. If the raw RMS current

is less than I2THR, then the angle expressed in PA2 is

used to compensate the phase angle. And if the raw

RMS current falls between I1THR and I2THR then PA1 is

used to compensate the phase angle. In this way, a

three-piece stepwise approximation of the phase

response of the current sensor is available.

To use a constant phase compensation, set I1THR and

I2THR to zero and insert the phase compensation value

into PA0.

The same processing can be performed to calculate

the reactive energy value. But reactive energy can be

calculated in another way: calculate apparent energy

by multiplying the raw RMS volts and raw RMS current,

square this value, then subtract the squared real

power. The square root of this value is the reactive

energy.

Similarly, apparent energy can be calculated in either

of two ways: either as the product of the raw RMS volts

and amps, or as the square root of the sum of the

squares of the real and reactive energy. Which of these

is selected depends on the value of the APPSEL bit in

the OPMODE2 register: if 0, then apparent energy is

the product of the raw RMS volts and amps and reac-

tive energy is calculated using the difference of

squares method; if 1, apparent energy is calculated

using the sum of squares method and reactive energy

is calculated directly from the complex energy.

Line Frequency and Phasor Angles: Line frequency

can be taken directly from the NS value. Recall that NS

is the number of frames in a DSP cycle. Since each

frame is 320μs, simply multiply NS by 320μs and divide

by CYCNT to obtain the line period. The reciprocal of

this is the line frequency.

To calculate phasor angles, the numbers of samples

between zero crossings on phase A and B and on phase

A and C are taken. Since NS is the number of samples

during a complete DSP cycle, it is easy to calculate the

fraction of a complete cycle. The software then converts

this value to degrees and adjusts it such that no negative

angles are reported. No calibration is required for line

frequency and phasor angle calculation.

Energy Accumulation

Once real and reactive energy over the most recent

DSP cycle has been calculated, it is necessary to accu-

mulate the result.

For reactive energy, the result accumulated during any

DSP cycle may be positive (for an inductive load) or

PA I I THR

PA I THR I I THR

RMS

≥

>≥

11 2

,,I I THR

RMS <

⎧

⎨

⎪

⎩

⎪

⎫

⎬

⎪

⎭

⎪

PHASE

COMPENSATION

PA0

PA1

PA2

REAL/REACTIVE

PROCESSING

LINEARIZATION AVERAGE

AVG_C

EREAL

OFFS_HI

GAIN_LO

OFFS_LO

LINEARIZATION

OFFS_HI

GAIN_LO

OFFS_LO

E_GAIN

E_RAWREAL

E_RAWREACTIVE

Figure 11. Phase Compensation for Energy Calculations

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 59

AVERAGE

AVG_C

EAPPARENT

E_GAIN

APPSEL

X2 + Y2

E_RAWREAL

E_RAWREACTIVE

X2 - Y2

X × Y

RAW_I

RAW_V

AVERAGE

AVG_C

EREACTIVE

E_GAIN

APPSEL

Figure 12. Apparent and Reactive Energy Calculations

negative (for a capacitive load). These values are sepa-

rately accumulated. This means that during any one

DSP cycle, only positive or negative reactive energy will

be accumulated.

Similarly, for real energy, the result accumulated during

any DSP cycle can be positive (that is, energy is deliv-

ered to the load) or negative (that is, energy is driven

back into the line). As is performed for reactive energy,

these values are separately accumulated.

Apparent energy is also accumulated, but since this

value is always positive or zero, there is only one

apparent energy accumulator.

From time to time, the accumulators generate an over-

flow. When this occurs, the appropriate bit is set in the

overflow status register X.EOVER.

When an overflow occurs, supervisory code running on

the host processor must make the appropriate adjust-

ments in the reported energy. In many cases, this could

simply involve incrementing an overflow counter. The

host processor must then clear the overflow indication.

No-Zero-Crossing Detection

The MAXQ3180 monitors the voltage signal on each

phase for zero-crossing events. If no ascending zero

crossings are detected within a specified number

(NZX_TIMO) of analog scan sample periods, the

NOZXF (X.FLAGS) flag is set by the MAXQ3180 to noti-

fy the master of this condition. If the NOZXM bit is set,

this flag sets the NOZX bit in the IRQ_FLAG. If the inter-

rupt enable bit ENOZX is set to 1, the interrupt signal

IRQ is driven low by the MAXQ3180 whenever NOZX =

1. The master can clear NOZXF and NOZX back to 0 to

remove the interrupt condition.

Phase Sequence Status

A phase sequence status bit PHSEQ indicates the

order in which zero crossings are detected. When a

zero-crossing event occurs on the phase A voltage sig-

nal, followed by phase B, phase C, and then phase A

again, this bit cleared. If a zero crossing on phase A is

then followed by a zero crossing on phase C, then

phase B, this bit set to 1.

RMS Voltage, RMS Current, and Energy

Calculation

For each of the three phases, the MAXQ3180 calcu-

lates RMS voltage and RMS current values, as well as

determines active and reactive energy, using a line-

cycle-based integration process.

Power Calculation (Active, Reactive,

Apparent)

The power, energy, and RMS calculation process con-

sists of two tasks: continuous accumulation and post-

processing triggered every CYCNT line cycles. The

accumulation task accumulates raw data obtained from

the AFE during CYCNT line cycles. This task is per-

formed continuously in the background by the

MAXQ3180. When a CYCNT line cycles accumulation

stage has completed, which is determined by a dedi-

cated frame counter exceeding the NS level, the raw

integral accumulator values are saved for postprocess-

ing and cleared, beginning the next cycle of accumula-

tion task. Then, the DSP postprocessing is triggered to

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

60 ______________________________________________________________________________________

process saved integrals and calculate energy, power,

etc., values. Note that the background accumulation

task continues while foreground postprocessing is tak-

ing place, i.e., both tasks are executed simultaneously

sharing CPU time. It is essential that the DSP postpro-

cessing calculations be completed before the next DSP

trigger to avoid losing accumulated data. The master

should allow enough processing time by adjusting the

R_ADCRATE register. Default settings provide plenty of

CPU time for both tasks.

The MAXQ3180 accumulates raw sums and calculates

line-cycle integrals for each voltage-current pair sepa-

rately. The individual power accumulators are:

• PA = VAx IA

• PB = IBx VBor -IBx VCor -IBx (VA+ VC) or -IBx

(VA- VC)

• PC = VCx IC

The PA and PC accumulators always operate in a sin-

gle mode: (VAx IA) for the PA accumulator, (VCx IC) for

the PC accumulator. Alternately, the operating mode of

the PB accumulator is defined by setting the

CONCFG[1:0] bits in the OPMODE1 register.

Energy Accumulation Start Delay

All filters have a certain settling time before accurate

energy readings can be accumulated. To avoid accu-

mulation of invalid data from filters that are still settling,

an energy accumulation timeout period can be set in

the ACC_TIMO register. When ACC_TIMO > 0, comput-

ed energy is not accumulated for ACC_TIMO of DSP

cycles. The MAXQ3180 will decrement the ACC_TIMO

ACC_TIMO reaches 0 value, energy accumulation

begins (or resumes, if ACC_TIMO was set to nonzero

value by the master). Pulse outputs are also disabled

when ACC_TIMO > 0. The default value of ACC_TIMO

is 0x05.

No-Load Feature

To avoid “meter creep,” no energy accumulation should

take place when measured current is less than a cer-

tain threshold. The NOLOAD register can be pro-

grammed to enable and configure this feature. If the

measured X.IRMS value for a phase (A, B, or C) falls

below the NOLOAD threshold, the energy accumulators

for this phase are not incremented. Setting NOLOAD =

0 disables this feature. Full scale is represented by

0x10000.

On Demand Calculations

So far in this discussion, the values being calculated

and managed in the MAXQ3180 have been based on

fundamental units meaningful to the device itself: volt-

age as a binary fraction of full-scale voltage; current as

a binary fraction of full-scale current, and time as a non-

integer multiple of the ADC frame time.

But a practical electricity meter must report its results in

standard units, such as volts, amperes, and watts. The

MAXQ3180 contains a mechanism to convert the inter-

nal units (“meter units”) to real world units (“display

units”). This conversion is performed in the conversion

constant (CC) registers.

For some of these values (voltage, current) the calcula-

tion is simple: multiply by the conversion constant. For

other values (power, energy) the calculation is more

complex. In any case, the value in the CC register

affects only the conversion from a meter unit to a dis-

play unit; calibration is handled separately in the gain

adjustment registers for each recorded value.

The results of all on-demand calculations are reported

as 8-byte (64-bit) values of which no more than 6 bytes

(48 bits) are significant. Eight bytes are used as a com-

mon length; however, fewer bytes can be requested for

those registers known to have smaller maximum values.

For example, the power factor virtual register has a

maximum value that is expressed in only 3 bytes; con-

sequently, the register can be requested with a length

of 4 bytes without loss of data.

RMS Volts, RMS Amps

These registers (V.A, V.B, V.C, I.A, I.B, I.C) are calculat-

ed by simply multiplying the calculated RMS value

(A.VRMS, B.VRMS, C.VRMS, A.IRMS, B.IRMS, C.IRMS)

by the contents of the VOLT_CC or AMP_CC register.

Since the RMS voltage and RMS current are given in

32-bit registers and the conversion coefficients are

given in 16-bit registers, the result of the product is 48

bits.

Regardless of the internal units used, VOLT_CC and

AMP_CC can be tailored so that the LSB of the virtual

to have a 32-bit value representing milliamps, one

could multiply by a value that scaled the register such

that the LSB was 2-16mA. Then, discard the low-order

16 bits. The result is milliamps with 32 bits of precision;

thus, the maximum current that could be represented

would be 4,294,967,296mA, or just over 4MA.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 61

The VOLT_CC and AMP_CC values can be calculated

from the full-scale voltage or full-scale current and the

desired value of one LSB in the display register:

Example: Assume the full-scale current is 102.4A, and

that we desire a 1nA LSB. The calculation would pro-

vide an AMP_CC value of:

102.4/(224 x 10-9) = 6104 = 0x17D8

Power

The MAXQ3180 measures energy. But power is just

energy per unit time, and the MAXQ3180 keeps track of

the time unit over which energy is accumulated. This is

simply the NS value, the fractional number of samples

that comprises one DSP cycle. So converting energy to

power is as simple as dividing the accumulated energy

over one DSP cycle by NS. Multiplying by a conversion

constant (PWR_CC) gives power in user-established

units.

The power registers (PWRP.A, PWRP.B, PWRP.C,

PWRQ.A, PWRQ.B, PWRQ.C, PWRS.A, PWRS.B,

PWRS.C) are calculated by multiplying the accumulat-

ed energy (A.ACT, A.REA, A.APP, B.ACT, B.REA,

B.APP, C.ACT, C.REA, C.APP) by the conversion coeffi-

cient (PWR_CC) and then dividing by NS. The result is

the 48-bit average power over the most recent DSP

cycle, in units established by the conversion coefficient.

The PWR_CC value can be calculated from the full-

scale voltage, the full-scale current, and the desired

value of one LSB in the display register:

Example: For this example, assume the full-scale cur-

rent is 102.4A, the full-scale voltage is 558.1V, and that

the desired LSB is milliwatts after discarding the 16

LSB; that is, the desired LSB is 2-16 milliwatts. Perform

the following calculation:

102.4 x 558.1/(232 x 2-16 x 10-3) = 872 = 0x0368

Power Factor

Power factor is calculated as real power divided by

apparent power. But note that apparent power can be

calculated in either of two ways: either as a square root

of the sum of the squares of the real and reactive

power, or more commonly as the product of the RMS

voltage and current measurement. The power factor as

reported could change when one or the other of these

methods is used.

The power factor is multiplied by 214 before it is report-

ed; thus, unity power factor is given by 16,384 decimal

(0x4000).

Line Frequency

The line frequency is derived directly from the mean NS

values over the three phases. It is reported as millihertz;

thus, a 50Hz line frequency is reported as decimal

50,000 (0xC350).

Phasor Angles

The phasor angles are taken directly from the angular

measurement values determined at each DSP cycle.

The angle is reported in units of 0.01 degree; thus, a

120° phasor is reported as decimal 12,000 (0x2EE0).

Energy

Energy is read as the net energy directly scaled from

the appropriate registers. For example, the energy read

from the ENRP.A register (real energy, phase A) is

composed of the difference between the A.EAPOS (real

energy, positive direction, phase A) and A.EANEG (real

energy, negative direction, phase A) registers scaled

by the ENR_CC register.

Note that the energy registers (ENRP.A, ENRP.B,

ENRP.C, ENRP.T, ENRQ.A, ENRQ.B, ENRQ.C, ENRQ.T,

ENRS.A, ENRS.B, ENRS.C, ENRS.T) represent the ener-

gy, in every case, since the last overflow event. For this

reason, software must keep track of overflow and make

adjustments accordingly when using this register set.

To calculate the ENR_CC register value, begin with the

full-scale voltage and full-scale current, the frame time,

and the desired LSB value for energy. Then perform the

following calculation:

Example: It is essential to ensure that the correct units

are maintained throughout the calculation. In this exam-

ple, assume that the full-scale voltage is 558.1V, the

full-scale current is 102.4A, the frame time is the default

of 320μs, and the desired LSB is 100 milliwatt-hours

after the 32 bits are discarded; that is, the LSB is 0.1 x

2-32 watt-hours. Notice, however, that the frame time is

given in microseconds

and must be converted to hours

before the calculation can be performed: 320μs is 88.9

x 10-9 hours. So the calculation proceeds as follows:

102.4 x 558.1 x 88.9 x 10-9/(216 x 0.1 x 2-32) = 3329 =

0x0D01

ENR CC IVt

ENR LSB

FS FS FR

=××

×216

PWR CC IV

PWR LSB

FS FS

=×

×232

VOLT CC V

VOLT LSB

=×224

AMP CC I

AMP LSB

=×224

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

62 ______________________________________________________________________________________

Meter Pulse

The purpose of a meter pulse is generally to advance a

mechanical counter when such a device is used as a

display. Meter pulses are also used during calibration

since time intervals can be measured with great preci-

sion.

The MAXQ3180 supports two meter pulse outputs.

These outputs can be configured for either active posi-

tive or active negative pulses by means of the POPOL

bit in the OPMODE1 register. When triggered, the pulse

goes to its active state and remains there for a period of

time defined by the PLS1_WD or PLS2_WD register,

and then returns to the inactive state (unless triggered

again).

The PLS1_WD and PLS2_WD registers contain the time

in ADC frame periods that the pulses remain in the

active state when triggered. By default, these registers

contain decimal 156 (0x9C) giving, at the default frame

rate, a pulse width of 50ms.

Each pulse generator can select one parameter to be

accumulated over any combination of the three phases.

For example, one could select real energy accumulated

over all three phases for pulse output 1, and reactive

energy accumulated over all three phases for pulse

output 2. The particular parameters that can be accu-

mulated are given in the register table.

Among the quantities that can be accumulated by the

pulse subsystem are the arithmetic active energy (that

is, the accumulated positive real energy minus the

accumulated negative real energy) and the absolute

active energy (that is, accumulated positive real ener-

gy plus accumulated negative real energy). Other

quantities include RMS voltage and current, positive

and negative real energy and reactive energy in each

of the four quadrants. Select the desired accumulation

value in the QNSEL field of the PLSCFG1 and

PLSCFG2 register.

Also in the pulse configuration registers you can select

which phases to include in the accumulation. Set any or

all the PHASEA, PHASEB, and PHASEC bits in the

PLSCFG1 or PLSCFG2 registers to include them in the

accumulation.

Generating Pulses

On every DSP cycle, the MAXQ3180 adds the value in

the selected register (or set of registers) to the pulse

accumulator. If the value in the pulse accumulator

exceeds the value in the associated threshold register

(THR1 or THR2), then a pulse is started and the value in

the threshold register is subtracted from the value in the

pulse accumulator.

Meter Constant

A meter constant is the number of pulses that are gen-

erated during a standard measurement interval; for

example, a meter might specify a meter constant of

1600 pulses per kilowatt-hour. The THR1 and THR2

registers are used to specify the meter constant

according to the following formula:

In this formula, THR is the value to be written to the

threshold register, KMis the desired meter constant (in

pulses per kilowatt hour), IFS and VFS are the full-scale

voltage and current, respectively, and tFR is the frame

period in units of hours, as in the previous calculation.

As an example, assume once again a full-scale voltage

value of 558.1V = 0.5581kV, a full-scale current value of

102.4A, a desired meter constant of 1600 pulses per

kilowatt hour, and a default frame time of 320μs (88.9 x

10-9 hours). The threshold register value can be calcu-

lated as:

65,536/(1600 x 102.4 x 0.5581 x 88.9 x 10-9) =

8,063,071 = 0x7B085F

Increasing the value of the threshold register

reduces

the meter constant (that is, there are fewer pulses per

kilowatt-hour); reducing the threshold register

increases

the meter constant (that is, there are more pulses per

kilowatt-hour.)

Interrupts

The MAXQ3180 contains an interrupt subsystem to

relieve the host processor of the burden of constantly

polling the device for status. Instead, under certain cir-

cumstances, the MAXQ3180 can activate an external

pin to alert the host processor that some condition

requiring host attention has occurred.

Interrupts are managed globally by the IRQ_MASK and

IRQ_FLAG registers. In general, when a bit becomes

set in the IRQ_FLAG register, an interrupt is generated

if the corresponding bit is set in the IRQ_MASK register.

Interrupts can be configured for the following conditions:

PWRF: This flag indicates the VDVDD to the

MAXQ3180 has fallen below its nominal operating

threshold (about 2.85V). This can be taken as an

indication that power failure is imminent and that the

host processor should begin taking steps to ensure

an orderly shutdown.

CHSCH: This flag indicates that the CHKSUM regis-

ter changed its value.

THR KI V t

MFS FS FR

=×× ×

216

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 63

EOVF: Energy overflow. This flag indicates that one or

more energy accumulators (X.EAPOS, X.EANEG, etc.)

have overflowed. In a traditional meter, the host

processor would poll the MAXQ3180 to determine

which of the energy accumulators have overflowed and

adjust its internal accounting registers accordingly.

OC: The RMS current value on one or more of the

phases over the most recent DSP cycle has exceed-

ed the value set in the OCLVL register.

OV: The RMS voltage on one or more of the phases

over the most recent DSP cycle has exceeded the

value set in the OVLVL register.

UV: The RMS voltage on one or more of the phases

over the most recent DSP cycle has failed to exceed

the value set in the UVLVL register.

NOZX: Zero crossings were not detected on one or

more of the phases. The detection time is defined in

the NZX_TIMO register. The resolution for the

NZX_TIMO register is the duration of one ADC sam-

ple time (nominally 40μs).

DCHA: Tells the host processor that the direction of

net real energy flow on one of the three phases has

changed during the current DSP cycle as compared

to the previous DSP cycle.

DCHR: Tells the host processor that the direction of

net reactive energy flow on one of the three phases

has changed during the current DSP cycle as com-

pared to the previous DSP cycle.

DSPRDY: Indicates the latest DSP cycle has just

completed.

DSPOR: Indicates that the processing for the previ-

ous DSP cycle had not been completed before the

current DSP cycle became available for processing.

This overflow indication should never be seen in the

default configuration; however, under some condi-

tions (faster ADC rate, slower CPU clock) the pro-

cessing requirements may exceed the number of

CPU cycles available for DSP processing. Under

these circumstances, the clock rate may be

increased, the ADC rate may be reduced (that is,

the R_ADCRATE register may be increased), or the

functional load (such as fundamental mode calcula-

tions) may be cut.

Note that when DSPOR becomes set, all DSP calcu-

lations as well as all pulse outputs are invalidated.

The appropriate host response is to take the remedi-

al action described above and discard the current

set of DSP result values.

Each phase has a local register that contains copies of

the OC, OV, UV, NOZX, DCHA, and DCHR bits. Thus,

to determine which phase(s) have exception conditions

requires four reads: the IRQ_FLAG register to deter-

mine which conditions are active that are causing the

interrupt to occur, and then a read to A.FLAGS,

B.FLAGS, and C.FLAGS to determine which of the

phases have the indicated condition.

Finally, each phase has a pair of local registers that

contain overflow flags for each energy accumulator. If

the EOVF bit is set in the IRQ_FLAG register, the host

should then read the A.EOVER, B.EOVER, and

C.EOVER registers to determine which of the phases

have overflow conditions. If fundamental mode opera-

tion is enabled, the host should read A.EFOVER,

B.EFOVER, and C.EFOVER as well. Each of these reg-

isters contains a bit for each of real and reactive energy

in both positive and negative direction as well as

apparent energy.

Overvoltage and Overcurrent Detection

The MAXQ3180 detects overvoltage and overcurrent

events and can issue interrupt request signals to the

master when these events occur. The overvoltage level

can be programmed into the OVLVL register, while the

overcurrent level is determined by the OCLVL register.

Both OVLVL and OCLVL registers represent the bits

23:8 of the VRMS or IRMS registers. Any time the

MAXQ3180 detects the RMS-value exceeding a thresh-

old level, the OV or OC interrupt flag is set. If enabled,

any of these flags issues an interrupt request. All inter-

rupt flags are “sticky” bits—the MAXQ3180 never

clears them on its own unless a reset occurs. The inter-

rupt flags should be cleared by the master by writing

the appropriate register.

Meter Units to Real Units Conversion

All energy calculations, including various threshold

checks, are performed internally in fixed format in meter

units. Therefore, the threshold values must be supplied

by the user in meter units as well. This section summa-

rizes how to convert real units (V, A, kWh, W, and kAh)

into meter units and vice versa.

The conversion factors are based on the settings of tFR,

VFS, and IFS, defined by the user’s design.

tFR is analog scan frame timing. This parameter is

defined by the R_ADCRATE setting and system clock

frequency fSYS:

tFR = (R_ADCRATE + 1) x 8/fSYS

Default conditions are R_ADCRATE = 319, fSYS = 8MHz.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

64 ______________________________________________________________________________________

VFS is full-scale voltage. This is the input voltage that

produces full-scale ADC output; defined by the hard-

ware voltage transducer ratio VTR and ADC full-scale

input voltage VFSADC:

VFS = VFSADC x VTR

Default conditions are VFSADC = 1.024V. VTR is design

dependent.

IFS is full-scale current. This is the input current that

produces full-scale ADC output; defined by the hard-

ware current transducer ratio ITR and ADC full-scale

input voltage VFSADC:

IFS = VFSADC x ITR

Default conditions are VFSADC = 1.024V. ITR is design

dependent.

Meter units are defined with respect to the base para-

meters as shown in Table 5.

When reading virtual registers, the MAXQ3180 uses the

configurable conversion coefficients AMP_CC,

VOLT_CC, PWR_CC, and ENR_CC to return meaningful

data. Table 6 describes how to set the coefficients.

Table 6. Virtual Register Coefficients

VIRTUAL REGISTER OUTPUT RESOLUTION

(1 LSB), DEFINED BY USER COEFFICIENT

Power:

PWRP.X, PWRQ.X, PWRS.X, PWRPF.X,

PWRQF.X, PWRSF.X

PWR_LSB PWR_CC = MU_PWR/PWR_LSB

Voltage:

V.X VOLT_LSB VOLT_CC = MU_VOLT/VOLT_LSB

Current:

I.X AMP_LSB AMP_CC = MU_AMP/AMP_LSB

Energy:

ENRP.X, ENRQ.X, ENRS.X, ENRPF.X,

ENRQF.X, ENRSF.X

ENR_LSB ENR_CC = MU_ENR/ENR_LSB

Current RMS: X.IRMS

Pulse output current RMS

THR1 or THR2, when pulse output configured to IRMS

MU_AMP = IFS/224

Voltage RMS: X.VRMS

Pulse output RMS voltage

THR1, or THR2 when pulse output configured to VRMS

MU_VOLT = VFS/224

Energy: X.ACT, X.REA, X.APP, X.EAPOS, X.EANEG, X.ERPOS,

X.ERNEG, X.ES

Fundamental Energy: X.ACTF, X.REAF, X.APPF, X.EAFPOS,

X.EAFNEG, X.ERFPOS, X.ERFNEG, X.ESF

Pulse Output Energy: THR1 or THR2

MU_ENR = VFS x IFS x tFR/216

Power: PWRP.X, PWRQ.X, PWRS.X MU_PWR = VFS x IFS/232

When X.ESF Contains Amp-Hours: X.ESF MU_AH = IFS x tFR/216

OCLVL, NOLOAD, I1THR, I2THR IFS/216

OVLVL, UVLVL VFS/216

Table 5. Meter Unit Definitions

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 65

Units Conversion Examples

The conversions from meter units to physical units are

illustrated with the simplified input circuits in Figures 13

and 14. The voltage input circuit is a voltage-divider.

Current input is through a current transfer with turn ratio

of 2000:1.

The voltage transducer ratio (VTR) = (R1 + R2)/R2 =

545, VFS = 558.1V.

The current transducer ratio (ITR) = CT_N/(2 x R) =

2000/(2 x 10) =100 (A/V), IFS = 102.4A.

The input circuits should be designed to avoid getting

too close to the ADC input full sale at the specified

maximum ratings. So for the above circuits, we would

specify the maximum input current = 70A (RMS) and

maximum voltage = 390V (RMS), to ensure that peak of

sinusoudal waveform never exceeds IFS or VFS.

Use the default ADC timing tFR = 320μs, we get the fol-

lowing meter unit to physical unit conversion coeffi-

cients (these coefficients are not part of the MAXQ3180

registers):

MU_AMP = IFS/224 = 6.1E-6 (A)

MU_VOLT = VFS/224 = 33.3E-6 (V)

MU_PWR = VFS x IFS/232 = 13.3E-6 (W)

MU_ENR = VFS x IFS x tFR/216 = 77.5E-9 (Wh)

For example, if we get 0x07654AF0 from reading

0x1CC register (phase A current RMS), the current

value it represents is

0x07654AF0 x MU_AMP = 47.33 (A)

For some low-end host microcontrollers, doing the

above math multiplication above could be difficult. For

this reason, the MAXQ3180 provides conversions for

some commonly needed parameters through the

VOLT_CC, AMP_CC, PWR_CC, and ENR_CC registers.

For example, if you want to display current in the reso-

lution of 1mA, without having to use a multiplication

operation to convert from the meter unit value

0x07654AF0, you would set AMP_CC to 0x0190, and

read from virtual register 0x831 (phase A RMS current).

The output would be 0xB8E45170. Dropping the lower

2 bytes (right shifting 16 bits) gives 0xB8E4, or 47332

decimal (47332mA).

AMP_CC is computed as follows:

AMP_CC = (IFS/224)/AMP_LSB = MU_AMP/AMP_LSB

AMP_LSB = 0.001/216 (A)

IFS = 102.4A

AMP_CC = (102.4/224)/(0.001/216) = 400d = 0x0190

Calibration Procedure

Calibration Overview

Calibration ensures that the recorded voltage, current,

energy, and power are in accordance with the design

criteria. Before creating a calibration regimen, establish

the fundamental units of the meter: the full-scale volt-

age and current. Then adjust the gain registers using

calculated calibration constants to produce the expect-

ed reading in the raw current, voltage, energy, and

power factor registers.

The calibration constants should be stored in non-

volatile memory by the host microcontroller. Upon any

reset or loss of power, the host microcontroller must

reload the MAXQ3180 with the constants.

Calibration always follows a set of fundamental steps:

• Apply a known signal (voltage/current/power) to the

meter.

• Read the meter.

• Calculate the correction factor based on the differ-

ence between the applied signal level and the meter

reading.

• Write the correction factor to the appropriate register.

MAXQ3180

I0P

VCOMM

IA (AC)

I0N

10Ω

Figure 14. Sample Current Input Circuit

MAXQ3180

VOPVA (AC)

1kΩ

544kΩ

Figure 13. Sample Voltage Input Circuit

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

66 ______________________________________________________________________________________

• Read the meter quantity again to verify the calibra-

tion.

Note that these steps can occur more than once for a

given signal type to verify readings at different signal

levels.

There are two methods to read the meter in the above

second step. The first is to read the raw register associ-

ated with the value under calibration, for example,

A.VRMS for the phase A voltage channel; A.IRMS for

the phase A current channel, and A.ACT for phase A

real power.

The second calibration method assigns a pulse output

to the value being calibrated and measures the pulse

period. In practical use, the method chosen depends

on the specific application and the available equip-

ment. For example, in some applications the voltage

and current are of no concern, but the energy accumu-

lation must be very accurate. For these applications,

meter calibration sets with built-in pulse measurement

facilities can make the most sense.

The calibration procedure involves the following gener-

al steps:

• Calibrate voltage for a given phase by applying a

known voltage and adjusting the voltage gain

(A.V_GAIN for phase A) until the RMS voltage

(A.VRMS for phase A) reads the applied voltage in

the designated units.

• Calibrate current by applying a known current and

adjusting the current gain (A.I_GAIN for phase A)

until the RMS current (A.IRMS for phase A) reads the

applied current in the designated units. If desired,

the current can be calibrated at two points (low

range and high range) for more accuracy.

• Once the current gain and voltage gain are calibrat-

ed, the power/energy should not require any addi-

tional adjustment for most situations. Although, a

separate power gain register is available for further

fine-tuning of the power/energy accuracy. One must

keep in mind that anytime voltage or current is recali-

brated, the power or energy accuracy is naturally

affected. So the power gain should be recalibrated to

achieve the desired accumulative effect of voltage,

current, and power gains.

• Calibrate the phase offset by applying a power factor

load and adjusting the phase angle offset according-

ly. If desired, the phase offset can be calibrated at

up to three points for more accuracy.

Once these elements are calibrated for each phase, all

other information (power factor, reactive power, appar-

ent power, etc.)is also properly calibrated. The descrip-

tions in the following sections deal specifically with

phase A, but the same procedure is followed with phas-

es B and C.

Calibrating Voltage

Ensure that there is no previous value in the gain regis-

ter, A.V_GAIN, by setting this register to 0x4000.

• Apply a known voltage with RMS value close to the

desired maximum operating voltage (and less than

VFS/√2).

• Read the A.VRMS register. Note the value.

• Convert the known value to meter units by dividing it

by MU_VOLT (= VFS/224).

• Divide the applied value (in meter unit) by the value

read from the MAXQ3180. The result should be a

value between 0 and 2. If the value falls outside of

this range, you have probably miscalculated VFS.

• Multiply the calculated value by 214. The result is the

gain value to be programmed into A.V_GAIN. Ensure

the most significant bit is 0.

When the gain value is programmed, wait for 2 to 3

seconds, reread the RMS value from A.VRMS. Check

that the measured value is correct by comparing

A.VRMS against the applied voltage in meter unit.

Voltage Calibration Example

Assumptions: VFS is 558.1V. The applied voltage is 240

VRMS.

• Convert the applied voltage to meter units. This cal-

culation gives 240 x 224/558.1 = 7,214,714 =

0x006E1679.

• Read the A.VRMS register. You read 0x0708029.

This is 7,372,841 decimal.

• Divide the applied voltage by the voltage read from

the meter. The result is 7,214,714/7,372,841 =

0.97855.

• Convert to integer by multiplying 214: 16,384 x

0.97855 = 16,033 = 0x3EA1. Write this value to the

A.V_GAIN register.

Calibrating Current

Ensure that there is no previous value in the gain regis-

ter, A.I_GAIN, by setting this register to 0x4000.

• Apply a known current with RMS value close to the

desired maximum operating current (and much lower

than IFS/√2).

• Read the A.IRMS register. Note the value.

• Convert the known value to meter units by dividing it

by MU_AMP (= IFS/224).

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 67

• Divide the applied value (in meter unit) by the value

read from the MAXQ3180. The result should be a

value between 0 and 2. If the value falls outside of

this range, you have probably miscalculated IFS.

• Multiply the calculated value by 214. The result is the

gain value to be programmed into A.I_GAIN. Ensure

the most significant bit is 0.

When the gain value is programmed, wait for approxi-

mately 2 to 3 seconds, then reread the RMS value from

A.IRMS. Check that the measured value is correct by

comparing A.IRMS against the applied current in meter

unit.

Current Calibration Example

Assume IFS is 102.4A and the meter has a base current

of 10A and a maximum current of 60A.

• The meter is calibrated at the base current of 10A.

• Convert the applied current to meter units. This cal-

culation gives 10 x 224/102.4 = 1,638,400 =

0x00190000.

• Read the A.IRMS register. You read 0x0017DC85.

This is 1,563,781 decimal.

• Divide the applied current by the current read from the

meter. The result is 1,638,400/1,563,781 = 1.0477.

• Multiply by 214 x 1.0477 = 17,166 = 0x430E. Write

this value to the A.I_GAIN register.

Calibrating Phase Offset

For this calibration step, it is necessary to have a power

factor meter, capable of measuring phase angle, con-

nected in the same circuit as the MAXQ3180 meter.

Note that calibration can be performed at any precision

power factor setting. We use a pure resistive load (PF =

1.0) load to illustrate the procedure.

• Apply a resistive load to the meter; the current drawn

by the load should correspond to the base current of

your meter.

• Record the phase angle and direction (capacitive or

inductive) reported on the power factor meter.

• Read and record the real and reactive energy from

the X.ACT and X.REA registers. Divide the reactive

energy by the real energy. This is the tangent of the

power-phase angle.

• Read the X.REA register. If the high-order bit is set,

the power factor reported in the above step is capac-

itive. If the high-order bit is clear, the power factor

reported in the above step is inductive.

• Now determine the correction factor: treating capaci-

tive values as negative and inductive values as posi-

tive, subtract the angle read from the MAXQ3180

from the angle read from the reference meter. The

result is the compensation angle.

• Multiply the compensation angle (in radians) by

65,536. This is the value to write into X.PA0.

If I1THR and I2THR are left at their default values

(0x0000), then the value in X.PA0 is applied to the full

measurement range. Alternatively, you could write the

same value into X.PA0, X.PA1, and X.PA2. Then the

same compensation is applied through the whole mea-

surement range regardless of the I1THR and I2THR set-

tings. If desired, calibrate for the phase angle at up to

three different current levels to compensate for nonlin-

earity in the current sensor. See the

Advanced

Operation

section for more information.

Phase Offset Calibration Example

Assume the meter is a 10/60 meter; that is, the base

current is 10A and the maximum rated current is 60A.

IFS is 102.4A and VFS is 558.1V. The test point is 10A

and 240V.

• Connect the MAXQ3180-based meter under test in

series with a lab grade reference meter. See the con-

figuration below.

• Apply power to the meter and apply a load of 10A

resistive.

• Verify that the I1THR, I2THR, A.PA0, A.PA1, and

A.PA2 registers contain zero.

• Read the power factor on the reference meter. You

read 1.5° capacitive. This is not unusual. The load

might not be truly resistive or reactance in the test

configuration could be reflected in the measurement.

• Read the real energy from register A.ACT (0x1D0).

You read 0x2865D6 (2,646,510 meter units).

• Read the reactive energy from register A.REA

(0x1D4). You read 0xFFFFA5C0 (-23,104 meter

units).

• Divide the reactive by the active power: -23,104/

2,646,510 = -0.009.

LAB

METER

UNIT

UNDER

TEST

LOAD

LINE

NEUTRAL

Figure 15. Offset Testing Setup

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

68 ______________________________________________________________________________________

• Take the inverse tangent of this value. You get -0.5°;

that is, 0.5°capacitive.

• Subtract the UUT phase offset from the reference

meter phase offset. In this case, the phase needs to

move 1°toward the capacitive. Convert this value to

radians: 1°x π/180°= 0.0175 radians.

• Multiply this value by 65,536. The result is 572

(0x023C).

• Because the phase correction is toward the capaci-

tive, the value must be complemented. The two’s

complement of 0x023C is 0xFDC4. This is the value

that should be written to the PA0 phase compensa-

tion register.

At this point, the meter is compensated for a single

phase offset. If the phase offset were perfectly flat over

all current levels, that would be sufficient (and for many

current sensors, particularly current shunts, one point is

usually good enough.)

Interfacing the MAXQ3180 to

External Hardware

The MAXQ3180 has all the internal circuitry that is

needed for a sophisticated electricity meter, but specif-

ic external hardware is required when configuring the

meter for a particular application. The most critical

decision that must be made is how the load will be con-

nected to the power source, and how the meter will be

connected to measure power consumed in the load.

This section covers how to select hardware compo-

nents for a MAXQ3180 electricity meter.

Connections to the Power Source

Generally, three-phase power as delivered from the util-

ity consists of four wires: three voltage phases and a

neutral wire. In one typical three-phase delivery system,

measuring from neutral to any phase would read 120V,

while measuring from any phase to any other phase

would read 208V. Connecting a load so that load cur-

rent is taken from phase lines and returned to neutral is

called a wye-connected load. Connecting a load so

that load current is provided by one phase and

returned on another phase is called a delta-connected

load. The MAXQ3180 can measure power consumed in

either a wye-connected or a delta-connected load.

If the load is connected in a wye fashion, the voltage is

measured from the neutral lead to each of the phases,

and the current measuring device is placed in series

with the load, most often in the hot lead. The sensor is

not placed in the neutral lead to prevent a customer

from defrauding the utility by returning the current to

ground rather than neutral. A current sensor placed in

the hot lead makes fraud even more difficult.

A delta-connected load can have current measured in

two possible ways. If it is primarily desirable to know

how much power is delivered to the load, one can place

the current sensor in the load circuit between two phas-

es. But if it is more important to know how much current

is being drawn from each supply phase, each current

sensor is placed in the line circuit of each single phase.

Most utilities are only concerned with the total amount

of energy being consumed. If individually accounting

for the power delivered by each phase is not a require-

ment, it is not necessary to measure all three voltages.

Instead, knowing only two voltages and the three cur-

rents is all that is necessary to measure total energy

usage.

There are several ways of doing this. In a wye arrange-

ment, one of the phases—usually phase B—–can be

considered the voltage reference point instead of neu-

tral. Then the voltage measurements can be made from

phase A to phase B and from phase C to phase B. By

using some simple arithmetic, the power delivered by

phase A, phase B, and phase C can be calculated

even though only two voltages are available.

A second mechanism is to have a delta-connected

load, but with one leg—usually the BC leg—split into

two equal loads. The point where the load is split is

defined as the reference. In this arrangement, it is only

necessary to know the voltage between phase C and

the split and phase A and the split, since VC= -VA.

Finally, there is the connection arrangement in which

the load is in a delta configuration with the current sen-

sor at each load, but it is still desired to determine how

much current is in each supply branch. The MAXQ3180

supports all of these connection arrangements.

Sensor Selection

The MAXQ3180 supports a variety of voltage and cur-

rent sense elements. This section describes the proper-

ties of many of these sensing devices.

Voltage Sensors

Voltage-Divider

A voltage-divider is an ideal voltage-sensing element

when there is no need for voltage isolation. Modern

resistors have virtually no parasitic capacitance or

inductance at the frequencies of interest in an electrici-

ty meter and have extremely low variation with tempera-

ture. When selecting resistors for a voltage-divider,

keep the division ratio high enough so that the peak

voltage value cannot exceed the maximum allowable

input voltage. In the MAXQ3180, the peak input voltage

is about 1V; consequently, a divider in the range of

400:1 to 600:1 is ideal.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 69

The second consideration is the total power dissipation

and voltage hold-off requirements of the resistor. It is

tempting to design a 400:1 divider with a 400kΩresis-

tor in series with a 1kΩresistor, but that would force the

400kΩresistor to dissipate about 140mW. This is not an

excessive amount of power, but if the design is to use

small SMT parts, it can handle greater than a 1/10W

SMT resistor. It is better to use a series of several small-

er components to improve system reliability.

Voltage Transformer

If isolation is required between the meter electronics

and the line, a voltage transformer is required. A volt-

age transformer is designed to faithfully transfer an AC

voltage applied on the primary side to a sensor on the

secondary side. On the primary side, a voltage-divider

is used to reduce the voltage to a workable level. On

the secondary side, a load resistor is selected so that

the current in the transformer windings is safely within

the transformer’s linear operating region.

Because the impedance seen in the primary side of the

transformer is equal to the impedance of the load resis-

tor in the secondary circuit plus impedance of the

transformer secondary winding at the operating fre-

quency, it is easy to calculate the value of the required

voltage-divider resistors in the primary side. For exam-

ple, assume we want a 500:1 divider ratio and assume

the load resistor is 600Ωand that the impedance of the

transformer secondary is 200Ω. The resistor required in

the primary is

(600 + 200) x 500 = 400kΩ

Often, this resistor is constructed from multiple

instances of a smaller value resistor; in this case, one

might use eight 50kΩresistors. Doing so minimizes the

voltage requirements for the resistor chain and reduces

the possibility that a single point of failure will cause a

catastrophic failure.

Current Sensors

Current Shunt

A current shunt is a low-value (approximately 100μΩto

a 100mΩ) resistor that converts a large-value current

into a small voltage. Shunts make good current sensors

because the output is an extremely linear representa-

tion of the measured current, current shunts can have

very low temperature coefficients, and they are inex-

pensive.

The power dissipated by a current shunt is inversely

proportional to its resistance and proportional to the

square of the output voltage. Consequently, there is

great incentive to reduce the resistance (and hence,

the output voltage) of a shunt. Often, full-scale current

in a shunt produces only a few millivolts of output, mak-

ing a front-end amplifier essential. The MAXQ3180

includes a gain-of-32 amplifier in the current channels

that is automatically cycled in and out, depending on

the input voltage of the current channels.

Current shunts operate at line voltage, thus, the AFE

must be isolated from the line. That means that in a

wye-connected meter, the current sensing must be per-

formed in the neutral return circuit (so that all voltages

into the current-sense amplifiers are referenced to neu-

tral). It also means that the use of a shunt is precluded

for delta-connected meters; the MAXQ3180 cannot tol-

erate the line-voltage differential between channels.

Current Transformer

In a current transformer, the primary is usually one turn

of thick wire or buss bar and the secondary is often

1000 turns or more of magnet wire. A ferrite core mag-

netically couples the two. Thus, a large current in the

primary turn creates a small current but large voltage in

the secondary winding.

For example, assume a current transformer with a 1000

turn secondary. A 10A current in the primary winding

induces a 10mA current in the secondary. This current

is made to flow through a so-called “burden” resistor,

usually 10Ωto 20Ω. Assuming a 20Ωburden, our 10A

current thus produces a 200mV signal in the secondary.

Advanced Operation

Modifying the ADC Operation

There are several other registers that directly affect the

AFE function. These registers directly affect the hard-

ware functionality, and should be modified only when it

is explicitly required. For example, if the MAXQ3180 is

operated at some frequency other than the nominal

8MHz system clock, modification of these registers by

supervisory code becomes necessary to maintain a

320μs frame time.

•R_ACFG: This register contains bits that disable the

ADC entirely, disable the voltage reference buffer

amplifier, and disable the ADC interrupt. Modifying

this register will likely disable or impair operation of

the MAXQ3180 internal firmware.

•R_ADCRATE: Modify this register to change the rate

at which the MAXQ3180 acquires samples. By

default, R_ADCRATE contains 319 decimal, which

means that the ADC acquires a sample every 320

system clocks. With an 8MHz clock, this translates to

40μs. If the system clock is slower, it may be advan-

tageous to reduce this value to keep a 40μs per sam-

ple time constant.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

70 ______________________________________________________________________________________

•R_ADCACQ: Modify this register to change the

acquisition time. The acquisition time is the time from

ADC power-on until conversion starts, and is provid-

ed to allow the input amplifiers to settle. By default

this is set to 47 decimal, or 6μs at an 8MHz system

clock. If the system clock rate is changed, then

R_ADCACQ should change so that this value

remains about 6μs.

Fine-Tuning the DSP Controls

Fine-Tuning the Line Frequency Measurement

Line frequency measurement is based on zero-crossing

detection. For that purpose each voltage signal is

passed through a digital lowpass filter, controlled by

the ZC_LPF register. This register specifies the b0coef-

ficient of a first-order LPF using following formula:

The MSB of this register must be zero.

For each phase A, B, and C, the MAXQ3180 counts the

number of scan frames (NS) between zero crossings

within a DSP cycle. Each individual phase A, B, or C

zero-crossing event contributes the raw NS count that

plugs as input to lowpass filter:

Yn= Yn - 1 + (AVG_NS/65,536) x (Xn- Yn - 1)

The filter coefficient is a signed 16-bit value and can be

configured by master. Here Y denotes the global NS

value, X denotes individual NS measurements pro-

duced by zero-crossing events detected on the phase

A, B, or C voltage channel. Note that if all three phase

voltages present, the filter above receives three inputs

each DSP cycle. The global NS value is used to gener-

ate the trigger for DSP processing. Note that the NS

value can be configured by the master, which could be

necessary if all three voltage signals are lost and no

zero-crossings are detected. The line period is then

calculated as a product of NS and the scan frame tFR.

The reciprocal of this value is the line frequency, which

can be obtained as a fixed-point value with 1 LSB =

0.001Hz by reading the LINEFR register.

Fundamental Mode Registers

The MAXQ3180 keeps another set of real and virtual

registers to track power and energy at the fundamental

line frequency. These “fundamental mode” registers

behave identically to the standard power and energy

registers, but are prefiltered to exclude harmonic

power.

The fundamental mode filter is specified in the B0FUND

and A1FUND registers. B0FUND is the feed-forward

coefficient and specifies the bandwidth of the funda-

mental mode filter; A1FUND is the feedback coefficient

and specifies the center frequency of the fundamental

mode filter.

In most cases, you can leave these filters at their

default values. If you wish to change the filter parame-

ters, first choose the desired bandwidth:

b0= πx bw x tFR

In this equation, bw is the desired bandwidth in hertz

and tFR is the frame period, typically 320μs. Set

B0FUND to b0x 216. By default, B0FUND contains dec-

imal 145 (0x91) giving a bandwidth of about 2.2Hz.

To set the center frequency, calculate a1according to

the following formula:

a1= 2 - 2(1 - b0) x cos(2πx fPK x tFR)

In this equation, b0is the previously calculated feed-

forward coefficient, fPK is the desired center frequency

in hertz, and tFR is the ADC frame period. Set A1FUND

to a1x 216. By default, A1FUND contains decimal 950

(0x3B6) giving a center frequency of 50Hz.

The fundamental mode filter is, by default, quite sharp

with 3dB points only 1.1Hz off of the center frequency.

This means that if the frequency drifts even only slight-

ly, the fundamental mode power measurement is likely

to have significant inaccuracy.

The MAXQ3180 provides a mechanism to track the fre-

quency by updating the A1FUND register on each DSP

cycle. This mechanism is automatically enabled by

default.

You may wish to disable the automatic tracking facility

under some circumstances, particularly if you have

defined a broader bandwidth than default and are com-

fortable that the frequency will not drift beyond the

passband. To disable the filter, set the DFUNA bit in the

OPMODE2 register.

You may also elect to disable fundamental mode oper-

ation completely. To do this, set the DFUN bit in the

OPMODE2 register.

Harmonic Measurement

In addition to the ability to measure power and energy

at the fundamental frequency, the MAXQ3180 provides

a mechanism to isolate a particular harmonic on any

voltage or current channel and measure the amplitude

of that harmonic.

To enable harmonic measurement, first select a voltage

or current channel to monitor. This is done in the

AUX_CFG register. The AUX_MUX field is the 3-bit

value that selects one of the three voltage channels or

one of the four current channels to monitor.

bZC LPF

016

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 71

The order of the harmonic is set in ORDH field of the

AUX_CFG register.

Also in the AUX_CFG register are two bits that enable

the auxiliary channel and enable harmonic measure-

ment on the auxiliary channel. To enable the auxiliary

channel, set the ENAUX bit. Once set, the MAXQ3180

will perform an RMS calculation on the selected chan-

nel. This is useful only for the IN(neutral current) chan-

nel, since every other voltage and current already have

RMS calculations applied by default. (The DADCNV bit

should be cleared in the SCAN_IN register in order to

enable sampling the INchannel.)

To enable harmonic measurement, set the ENHARM

bit. Now, the selected voltage or current signal is

passed to a filter that is identical to the second-order

fundamental filter, but that has separate parameters

(A1HARM, B0HARM).

Low-Power Measurement Mode (LOWPM)

This mode enables a subset of metering functions while

operating from the lower frequency internal RC oscilla-

tor to conserve power. The actual system clock fre-

quency used is the RC oscillator output frequency

divided by 8, which results in a system clock frequency

of approximately 1MHz.

The parameters provided in the LOWPM are:

• Voltage RMS

• Current RMS

• Ampere-Hour

The ampere-hour value is readable from the X.ESF reg-

isters (X = A/B/C). Entry to LOWPM mode only occurs

at the request of the master. The master must set the

LOWPM_E bit (register address 0xC03) to 1 to place

the MAXQ3180 into LOWPM mode. Entering LOWPM

mode changes the clock frequency, thereby invalidat-

ing a number of configuration registers. As a result, the

master must immediately reload the configuration regis-

ters and filter with new, updated values before metering

measurement operations can continue.

The master instructs the MAXQ3180 to exit LOWPM

mode by reading the LOWPM_X bit (register address

0xC04).

Temperature

The MAXQ3180 contains a temperature sensor that can

be used by host software for any purpose, including

compensating power readings for temperature effects.

Use the virtual register command (RAWTEMP, 0xC01)

to perform a temperature conversion. The MAXQ3180

returns raw ADC reading of voltage produced by the

temperature sensor.

Conversion from the arbitrary units to useful units (such

as degrees Celsius) requires taking one calibration

point and storing a conversion constant in the host

processor. The conversion constant is simply the value

(in absolute degrees) of one LSB.

To calculate the LSB value, take a reading at a known

temperature and divide the known temperature by the

reading. For example, assume you take a reading at

room temperature (23°C), and the reading is 0x7F00.

The degrees per LSB are then:

(23 + 273.15)/0x7F00 = 0.00911K

Now, assume at a later time you read the temperature

and see it is 0x84F0. To find the temperature in Celsius,

multiply by the degrees per LSB and subtract 273.15:

0x84F0 x 0.00911 - 273.15 = 36.8°C

Advanced Calibrations

Calibrating Current Offset

Ideal hardware should produce a current reading lin-

early proportional to the input current. However, due to

noise or other factors, the RMS current read by the

meter might not be precisely linear. The current offset

(X.OFFS_HI, X = A/B/C) can be used to compensate

the current channel nonlinearity.

Since the MAXQ3180 tracks the input current to deter-

mine what linearity compensation factors to use, the

user must choose two points (ilo and ihi) comfortably

above the low current threshold, and get the X.IRMS

current readings (rlo and rhi). Then calculate the Y-inter-

cept of the line drawn between the two points, that is,

the offset. To calculate the value for the offset register,

use the following formula. If LINFRM = 0:

If LINFRM = 1:

In this equation, ihi and rhi are the applied current and

the current reading, respectively, in meter units at the

higher of the two reference currents; ilo and rlo are the

applied current and the current reading, respectively, in

meter units at the lower of the two reference currents.

The gain (X.I_GAIN) may require recalibration after the

offset register updated.

offs ri ir

hi lo hi lo

lo hi

=−

−()24

offs ri ir

hi lo hi lo

hi lo

=−

−

22 22

24 2 2

2( )

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

72 ______________________________________________________________________________________

Calibrating Linearity

The current channel includes a variable-gain amplifier

that introduces a gain of 32 when the current falls

below the low current threshold (about 1/32 of full-scale

current IFS). Because the gain of the amplifier cannot

be controlled with arbitrary precision, and because

high gain implies increased noise, it may be necessary

to calibrate the MAXQ3180 to maintain linearity at the

lowest inputs.

There are two settings that manage low-current lineari-

ty: an offset setting, OFFS_LO; and a gain setting,

GAIN_LO. Setting the offset is simple. Ensure no cur-

rent is flowing in the current circuit. Read X.IRMS. To

calculate offset use following formula:

If LINFRM = 0:

If LINFRM = 1:

offs = -X.IRMS

Program the offs into the OFFS_LO register.

So, if the user reads 0x0113 from the X.IRMS register and

LINFRM = 1, program 0xFEED into the OFFS_LO register.

Setting the GAIN_LO register means applying a current

below the low-current threshold, reading the value from

the MAXQ3180, and adjusting the gain accordingly. Note

that, unlike offset, the low-end gain is

added

to the overall

gain provided in the I_GAIN register.

Apply a known current with peak value less than the

low-current threshold. Ensure that there is no previous

value in the low-current gain register, A.GAIN_LO, by

setting this register to 0x4000. Read the A.IRMS regis-

ter (0x1CC). Note the value. Convert the known value to

meter units by multiplying the known value (in amperes)

by 224 and dividing by IFS. Divide the results of this cal-

culation by the value read from the MAXQ3180. The

result should be a value between 0 and 2. Convert the

integer by multiplying 214, and ensure MSB is zero. The

result is the gain value to be programmed into

A.GAIN_LO.

Calibrating Power/Energy Gain

Once voltage and current have been calibrated, the

energy and power calculation automatically reflects the

calibrated voltage and current. However the energy

gain factor (X.E_GAIN, X = A/B/C) can be further tuned

to achieve even more accurate power and energy

result if necessary. For example, if the voltage and cur-

rent calibration sources are not as accurate as the

power/energy calibration source, then the additional

gain calibration may be necessary. The following pro-

cedure for power/energy gain calibration is outlined for

phase A.

• Apply a precision unity power factor power (applied

value) that is close to the desired normal operating

point.

• Read the PWRP.A register. Note the value.

• Convert the applied value to meter units by dividing it

by MU_PWR.

• Divide the applied value (in meter unit) by the value

read from the MAXQ3180. The result should be a

value between 0 and 2. If the value falls outside of

this range, IFS and/or VFS have probably been mis-

calculated.

• Multiply the calculated value by 214, and ensure the

MSB is zero. The result is the gain value to be pro-

grammed into A.E_GAIN.

• When the gain value is programmed, wait for 1 to 2

seconds, then reread the power value from PWRP.A.

Check that the measured value is correct by compar-

ing PWRP.A against the applied power in meter unit.

Multipoint Phase Offset Calibration

To perform the calibration at three current levels, note

the raw current value (X.IRMS) at each point. Label the

current values, from highest to lowest, I0, I1, and I2.

Program X.PA0, X.PA1, and X.PA2 with the phase offset

values calculated at I0, I1, and I2, respectively, as

described in the

Calibrating Phase Offset

section.

Finally, program I1THR with the average of I0and I1,

and program I2THR with the geometric average of I1

and I2. Now as the current changes the phase offset is

adjusted accordingly. See Figure 16.

offs XIRMS

=−(. )

I2THR

I1THR

PA2

I2I1I0

PA1

PA0

INPUT CURRENT

PHASE OFFSET

Figure 16. Phase Offset vs. Input Current Calibration

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 73

Advanced Register Configurations

Analog Scan Configuration Registers

Time Slot Assignment—Current Channel X = A/B/C (SCAN_IX)

(A: 0x008, B: 0x00C, C: 0x00A)

These registers configure the time slot normally assigned to current channels A/B/C. We recommend leaving these

registers at their default values. If they must be reassigned, one must ensure that all the current and voltage chan-

nels are reassigned properly so that the MAXQ3180 computes the power/energy parameters as intended by your

setup.

Bit: 7 6 5 4 3 2 1 0

Name: ADCMX DADCNV — — —

Reset A: 0x3 0 0 0 0

Reset B: 0x4 0 0 0 0

Reset C: 0x5 0 0 0 0

BIT NAME FUNCTION

7:4 ADCMX

Analog Conversion Select. This four-bit field determines which of the following analog inputs are sampled

during this time slot.

0000 = V0P - VN

0001 = V1P - VN

0010 = V2P - VN

0011 = I0P - I0N (Phase A Current: 0011)

0100 = I1P - I1N (Phase B Current: 0100)

0101 = I2P - I2N (Phase C Current: 0101)

0110 = INP - VN

1xxx = Temperature

All other values are reserved.

3 DADCNV ADC Disable. When set, disables the ADC for this time slot.

2:0 — Reserved.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

74 ______________________________________________________________________________________

Time Slot Assignment—Voltage Channel X = A/B/C (SCAN_VX)

(A: 0x009, B: 0x00D, C: 0x00B)

These registers configure the time slot normally assigned to voltage channels A/B/C. The user may wish to change the

PGG settings to match the voltage sensor. However, it is recommended that the user not modify the ADCMX settings.

BIT NAME FUNCTION

7:4 ADCMX

Analog Conversion Select. This four-bit field determines which of the following analog inputs are sampled

during this time slot.

0000 = V0P - VN (Phase A Voltage: 0000)

0001 = V1P - VN (Phase B Voltage: 0001)

0010 = V2P - VN (Phase C Voltage: 0010)

0011 = I0P - I0N

0100 = I1P - I1N

0101 = I2P - I2N

0110 = INP - VN

1xxx = Temperature

3 DADCNV ADC Disable. When set, disables the ADC for this time slot.

2:0 PGG

Programmable Gain Amplifier Select. This three-bit field configures the programmable-gain amplifier at

the front-end of the analog input. The field has the following values:

000 = Gain of 1

001 = Gain of 2

010 = Gain of 4

011 = Gain of 8

100 = Gain of 16

101 = Gain of 32

All other values are reserved and can cause unpredictable behavior if selected.

Bit: 7 6 5 4 3 2 1 0

Name: ADCMX DADCNV PGG

Reset A: 0x0 0 0x0

Reset B: 0x1 0 0x0

Reset C: 0x2 0 0x0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 75

Time Slot Assignment—Neutral Current Channel (SCAN_IN) (0x00E)

This register configures the time slot normally assigned to the neutral current channel. The user can change the

DADCNV bit to enable/disable neutral current sampling. It is recommended to leave the other bits of this register at

their default values.

Bit: 7 6 5 4 3 2 1 0

Name: ADCMX DADCNV — — —

Reset: 0x6 1 0 0 0

BIT NAME FUNCTION

7:4 ADCMX

Analog Conversion Select. This four-bit field determines which of the following analog inputs are sampled

during this time slot. All other values are reserved. By default, this register is set to 0110.

0000 = V0P - VN

0001 = V1P - VN

0010 = V2P - VN

0011 = I0P - I0N

0100 = I1P - I1N

0101 = I2P - I2N

0110 = INP - VN

1xxx = Temperature

3 DADCNV ADC Disable. When set, disables the ADC for this time slot.

2:0 — Reserved.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

76 ______________________________________________________________________________________

Time Slot Assignment—Temperature Channel (SCAN_TE) (0x00F)

This register configures the time slot normally assigned to the temperature measurement device. This register is

managed by the firmware and should not be modified by the host.

BIT NAME FUNCTION

7:4 ADCMX

Analog Conversion Select. This four-bit field determines which of the following analog inputs are sampled

during this time slot.

0000 = V0P - VN

0001 = V1P - VN

0010 = V2P - VN

0011 = I0P - I0N

0100 = I1P - I1N

0101 = I2P - I2N

0110 = INP - VN

0111 = Auto-zero ADC

1xxx = Temperature

By default, this register is set to 1000.

3 DADCNV ADC Disable. When set, disables the ADC for this time slot.

2:0 PGG

Programmable Gain Amplifier Select. This three-bit field configures the programmable-gain amplifier at

the front end of the analog input. The field has the following values:

000 = Gain of 1

001 = Gain of 2

010 = Gain of 4

011 = Gain of 8

100 = Gain of 16

101 = Gain of 32

All other values are reserved and can cause unpredictable behavior if selected. This register is managed

by the firmware and should not be modified by the host.

Bit: 7 6 5 4 3 2 1 0

Name: ADCMX DADCNV PGG

Reset: 0x8 1 0x2

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 77

Neutral Current and Harmonics

Auxiliary Channel Configuration (AUX_CFG) (0x010)

The MAXQ3180 can monitor the RMS value of one auxiliary channel in addition to its normal processing. The

Auxiliary Channel Configuration register selects which input the auxiliary channel processes and what processing is

applied to the auxiliary channel.

DSP System Configuration

System Clock Frequency (SYS_KHZ) (0x012)

This register contains the system clock frequency in kHz units. Because the default frequency is 8MHz, this register

defaults to 0x1F40.

Bit: 15 14 13 12 11 10 9 8

Name: — — — ORDH

Reset: 0 0 0 0 0 0 0 0

Bit: 7 6 5 4 3 2 1 0

Name: ENHARM ENAUX — — — AUX_MUX

Reset: 0 0 0 0 0 0 0 0

BIT NAME FUNCTION

15:13, 5:3 — Reserved.

12:8 ORDH

Order of Harmonic (1–21). The output of harmonic voltage is read via virtual register 0x830 and current

at 0x840.

7 ENHARM

Enable Auxiliary Channel Harmonic Filter. When set, the auxiliary channel is processed through the

harmonic filter. The parameters for this filter can be set in the B0HARM and A1HARM registers.

6 ENAUX Enable Auxiliary Channel. When set, enables auxiliary channel processing.

2:0 AUX_MUX

Auxiliary Channel Input Select. This three-bit field selects the input to be processed by the auxiliary

channel.

001 = IN

010 = VA

011 = IA

100 = VB

101 = IB

110 = VC

111 = IC

Bit: 15 14 13 12 11 10 9 8

Name: System Clock Frequency High Byte

Reset: 0x1F

Bit: 7 6 5 4 3 2 1 0

Name: System Clock Frequency Low Byte

Reset: 0x40

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

78 ______________________________________________________________________________________

Cycle Count (CYCNT) (0x01C)

This register contains the number of line cycles that will be accumulated in a single DSP cycle. When CYCNT line

cycles have been accumulated, the DSP performs power, power factor, and energy calculations. By default, the

cycle count is 0x10 (16 decimal).

Number of Scan Frames per DSP Cycle (NS) (0x040)

The NS register defines the fundamental timing for the electricity meter. It defines a DSP cycle in terms the period of

the ADC scan frame. Generally, this register is calculated and updated automatically by the MAXQ3180 firmware

based on the zero-crossing detection, and whether noise rejection (REJ_NS) and averaging (AVG_NS) are enabled.

Host code can write to this register in order to set the desired DSP cycle duration. The duration of one scan frame

(tFR) is represented as 0x00010000.

Bit: 15 14 13 12 11 10 9 8

Name: Cycle Count High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Cycle Count Low Byte

Reset: 0x10

Bit: 31 30 29 28 27 26 25 24

Name: Integer Portion, High Byte

Reset: 0x03

Bit: 23 22 21 20 19 18 17 16

Name: Integer Portion, Low Byte

Reset: 0xE8

Bit: 15 14 13 12 11 10 9 8

Name: Fractional Portion, High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Fractional Portion, Low Byte

Reset: 0x00

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 79

Filter Coefficients

Line Cycle Noise Rejection Filter (REJ_NS) (0x02C)

This register establishes the sensitivity of the NS rejection filter setting. NS is a measure of the line frequency. If a line

cycle occurs that is shorter or longer than the line cycle represented in the NS register, this filter determines whether

the cycle is used to update the NS value. For more information, see the NS register description. If this register is

zero, noise rejection is disabled for the line cycle counter.

Line Cycle Averaging Filter (AVG_NS) (0x02E)

This register determines whether the NS value is averaged over previous values or whether the most recently measured

value is used directly. If the value of this register is nonzero, the NS value is averaged using the following formula:

If the value of this register is zero, NS is not averaged. The MSB of this register must be zero.

yy AVGNS

nn nn

=+ −

−−

Bit: 15 14 13 12 11 10 9 8

Name: Line Cycle Noise Rejection Filter High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Line Cycle Noise Rejection Filter Low Byte

Reset: 0xC8

Bit: 15 14 13 12 11 10 9 8

Name: Line Cycle Averaging Filter High Byte

Reset: 0x40

Bit: 7 6 5 4 3 2 1 0

Name: Line Cycle Averaging Filter Low Byte

Reset: 0x00

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

80 ______________________________________________________________________________________

Meter Measurement Averaging Filter (AVG_C) (0x030)

This register determines whether the all other measured values in the electricity meter are averaged over time. If the

value of this register is nonzero, all measured meter values are averaged using the following formula:

If the value of this register is zero, no averaging is performed. The MSB of this register must be zero.

Meter Measurement Highpass Filter (HPF_C) (0x032)

This register specifies the b0coefficient of a first-order Butterworth filter using the following formula:

The MSB of this register must be zero.

bHPF C

016

yy AVGC

nn nn

=+ −

−−

Bit: 15 14 13 12 11 10 9 8

Name: Meter Measurement Averaging Filter High Byte

Reset: 0x40

Bit: 7 6 5 4 3 2 1 0

Name: Meter Measurement Averaging Filter Low Byte

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: Meter Measurement Highpass Filter High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Meter Measurement Highpass Filter Low Byte

Reset: 0xC8

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 81

Fundamental Filter Feed-Forward Coefficient (B0FUND) (0x034)

This register specifies the b0(feed-forward) coefficient for the fundamental-mode filter using the following formula:

The MSB of this register must be zero.

Fundamental Filter Feedback Coefficient (A1FUND) (0x036)

This register specifies the a1(feedback) coefficient for the fundamental-mode filter using the following formula:

aA FUND

116

bB FUND

016

Bit: 15 14 13 12 11 10 9 8

Name: Fundamental Filter Feed-Forward Coefficient High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Fundamental Filter Feed-Forward Coefficient Low Byte

Reset: 0x91

Bit: 31 30 29 28 27 26 25 24

Name: Fundamental Filter Feedback Coefficient Byte 3

Reset: 0x00

Bit: 23 22 21 20 19 18 17 16

Name: Fundamental Filter Feedback Coefficient Byte 2

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: Fundamental Filter Feedback Coefficient Byte 1

Reset: 0x03

Bit: 7 6 5 4 3 2 1 0

Name: Fundamental Filter Feedback Coefficient Byte 0

Reset: 0xB6

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

82 ______________________________________________________________________________________

Harmonic Filter Feed-Forward Coefficient (B0HARM) (0x03A)

This register specifies the b0(feed-forward) coefficient for the harmonic-mode filter using the following formula:

The MSB of this register must be zero.

Harmonic Filter Feedback Coefficient (A1HARM) (0x03C)

This register specifies the a1(feedback) coefficient for the harmonic mode filter using the following formula:

Zero-Cross Lowpass Filter (ZC_LPF) (0x05A)

This register specifies the lowpass filter applied for zero-cross detection. The MSB of this register must be zero.

aA HARM

116

bB HARM

016

Bit: 15 14 13 12 11 10 9 8

Name: Harmonic Filter Feed-Forward Coefficient High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Harmonic Filter Feed-Forward Coefficient Low Byte

Reset: 0x91

Bit: 31 30 29 28 27 26 25 24

Name: Harmonic Filter Feedback Coefficient Byte 3

Reset: 0x00

Bit: 23 22 21 20 19 18 17 16

Name: Harmonic Filter Feedback Coefficient Byte 2

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: Harmonic Filter Feedback Coefficient Byte 1

Reset: 0x18

Bit: 7 6 5 4 3 2 1 0

Name: Harmonic Filter Feedback Coefficient Byte 0

Reset: 0x31

Bit: 15 14 13 12 11 10 9 8

Name: Zero-Cross Lowpass Filter High Byte

Reset: 0x0B

Bit: 7 6 5 4 3 2 1 0

Name: Zero-Cross Lowpass Filter Low Byte

Reset: 0x00

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 83

Hardware Mirror Registers

ADC Configuration (R_ACFG) (0x04C)

This register is a mirror of a CPU register in the MAXQ3180. This register should not be modified by supervisory

code.

ADC Conversion Rate (R_ADCRATE) (0x04E)

This register specifies the number of system clock cycles between consecutive ADC conversions. It defaults to

0x13F (319 decimal), which specifies 320 CPU clock cycles between conversions. This register is a mirror of a CPU

Bit: 7 6 5 4 3 2 1 0

Name: ADCASD ADCRY ADCCD ADCBY ADCIE ARBE ADCE

Reset: 0 0 0x0 0 1 1 1

BIT NAME FUNCTION

7 ADCASD

Disable ADC Automatic Shutdown. Normally, the ADC analog section is powered off following a

conversion to conserve power. If this bit is set, the ADC leaves the analog section powered on

following a conversion.

6 ADCRY

ADC Data Ready. When a conversion is complete, this bit is set to indicate that data is available. This

bit generates an interrupt if ADCIE is set.

5:4 ADCCD

ADC Clock Divider. Sets the division ratio between the CPU master and ADC clock.

00 = divide by 1

01 = divide by 2

10 = divide by 4

11 = reserved

3 ADCBY

ADC Busy. When set, a single ADC conversion cycle is in progress. The bit is cleared on the

conclusion of the conversion cycle.

2 ADCIE ADC Interrupt Enable. If set, the ADC interrupts the CPU at the completion of a conversion cycle.

1 ARBE Reference Buffer Enable. If set, the reference buffer is enabled to drive the REFO pin.

0 ADCE ADC Enable. If set, the ADC hardware is activated.

Bit: 15 14 13 12 11 10 9 8

Name: ADC Conversion Rate High Byte

Reset: — — — — — — — 1

Bit: 7 6 5 4 3 2 1 0

Name: ADC Conversion Rate Low Byte

Reset: 0x3F

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

84 ______________________________________________________________________________________

ADC Settling Time (R_ADCACQ) (0x050)

This register is a mirror of a CPU register in the MAXQ3180. This register should not be modified by supervisory

code. This register specifies the time, in CPU clocks, that the ADC must wait after switching analog mux inputs

before beginning its conversion. This register defaults to 0x2F (47 decimal), which specifies a 48 CPU clock-cycle

delay from analog mux switching to the start of conversion.

SPI Configuration (R_SPICF) (0x052)

This register is a mirror of a CPU register in the MAXQ3180. This register configures the SPI port of the MAXQ3180.

Bit: 15 14 13 12 11 10 9 8

Name: ADC Settling Time High Byte

Reset: — — — — — — — —

Bit: 7 6 5 4 3 2 1 0

Name: ADC Settling Time Low Byte

Reset: — 0x2F

Bit: 7 6 5 4 3 2 1 0

Name: ESPII SAS — — — CHR CKPHA CKPOL

Reset: 1 0 0 0 0 0 0 0

BIT NAME FUNCTION

7 ESPII Enable SPI Interrupt. If set, arrival of a character on the SPI bus causes a CPU interrupt.

6 SAS

SPI Slave Select Polarity. If clear, SSEL is assumed to be active low; if set, SSEL is assumed to be

active high.

5:3 — Reserved.

2 CHR

SPI Character Length. If clear, characters on the SPI bus are assumed to be 8 bits; if set, characters on

the SPI bus are assumed to be 16 bits.

1 CKPHA

SPI Clock Phase. If clear, data is sampled on the leading edge of the clock (low-to-high if the clock is

active high, and high-to-low if the clock is active low). If set, data is sampled on the trailing edge of the

clock (high-to-low if the clock is active high, and low-to-high if the clock is active low).

0 CKPOL

SPI Clock Polarity. If clear, the clock is assumed to be active high; if set, the clock is assumed to be

active low.

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 85

Timeouts

Zero-Crossing Timeout (NZX_TIMO) (0x054)

This register specifies the time in ADC sample periods (default 40μs) that must elapse following a zero-crossing

event before the MAXQ3180 declares a “no-zero crossing” fault. When this fault is declared, the NOZXF bit in the

X.FLAGS register is set.

Communications Timeout (COM_TIMO) (0x056)

This register specifies the duration of SPI timeout in ADC frames (default 320μs).

Energy Accumulation Timeout (ACC_TIMO) (0x058)

This register specifies the time in DSP cycles that the MAXQ3180 waits before accumulating energy. If this register is

nonzero, it is decremented on each DSP cycle. If the result of the decrement is nonzero, the results of the DSP cycle

are discarded and are not accumulated to the energy registers. This register is useful for delaying the initiation of

energy accumulation on startup or after some hardware function has been modified.

Bit: 15 14 13 12 11 10 9 8

Name: Zero-Crossing Timeout High Byte

Reset: 0x23

Bit: 7 6 5 4 3 2 1 0

Name: Zero-Crossing Timeout Low Byte

Reset: 0x28

Bit: 15 14 13 12 11 10 9 8

Name: Communications Timeout High Byte

Reset: 0x03

Bit: 7 6 5 4 3 2 1 0

Name: Communications Timeout Low Byte

Reset: 0xE8

Bit: 15 14 13 12 11 10 9 8

Name: Energy Accumulation Timeout High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Energy Accumulation Timeout Low Byte

Reset: 0x05

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

86 ______________________________________________________________________________________

Phase-Angle Compensation

Phase Offset Current Threshold 1 (I1THR) (0x05C)

This register specifies the fraction of full-scale current that causes the MAXQ3180 to switch from PA0 to PA1 to pro-

vide phase-angle compensation. For more information, see the PA0, PA1, and PA2 register descriptions. The full-

scale current is represented by 0x10000.

Phase Offset Current Threshold 2 (I2THR) (0x05E)

This register specifies the fraction of full-scale current that causes the MAXQ3180 to switch from PA1 to PA2 to pro-

vide phase-angle compensation. For more information, see the PA0, PA1, and PA2 register descriptions. The full-

scale current is represented by 0x10000.

Miscellaneous Gain

Neutral Current Gain (N.I_GAIN) (0x12E)

This register contains gain compensation coefficient for the neutral current channel measurement. The raw values

are taken from the selected measurement quantity and scaled by N.I_GAIN/214.

Bit: 15 14 13 12 11 10 9 8

Name: Phase Accumulator Current Threshold 1 High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Phase Accumulator Current Threshold 1 Low Byte

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: Phase Accumulator Current Threshold 2 High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Phase Accumulator Current Threshold 2 Low Byte

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: Compensation Coefficient High Byte

Reset: 0x40

Bit: 7 6 5 4 3 2 1 0

Name: Compensation Coefficient Low Byte

Reset: 0x00

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 87

Gain, Fundamental Energy, Phase X = A/B/C (X.EF_GAIN) (A: 0x136, B: 0x222, C: 0x30E)

This register contains gain coefficient for phase X fundamental energy. The raw values are taken from the selected

measurement quantity and scaled by the following factor:

Linearity Compensation

Linearity Offset, High Range, Phase X = A/B/C (X.OFFS_HI) (A: 0x138, B: 0x224, C: 0x310)

This signed register contains the linearity offset for phase X current channel when the programmable gain amplifier

is set to unity gain (that is, the measured current is above the low current threshold). The signed value represented

by this register is added to the current value according to following formula:

if LINFRM = 0:

if LINFRM = 1: X.IRMS + X.OFFS_HI x 24

Linearity Gain Coefficient, Low Range, Phase X = A/B/C (X.GAIN_LO)

(A: 0x13A, B: 0x226, C: 0x312)

This register contains the linearity coefficient for phase X current channel when the programmable gain amplifier is

set to gain of 32 (that is, the measured current is below the low current threshold). The effective gain is given by the

equation:

XGAIN LO._

214

XIRMS XOFFS HI.._

224

2+×

XEF GAIN._

214

Bit: 15 14 13 12 11 10 9 8

Name: Gain Coefficient High Byte

Reset: 0x40

Bit: 7 6 5 4 3 2 1 0

Name: Gain Coefficient Low Byte

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: Linearity Offset High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Linearity Offset Low Byte

Reset: 0x00

Bit: 15 14 13 12 11 10 9 8

Name: Linearity Coefficient High Byte

Reset: 0x40

Bit: 7 6 5 4 3 2 1 0

Name: Linearity Coefficient Low Byte

Reset: 0x00

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

88 ______________________________________________________________________________________

Linearity Offset, Low Range, Phase X = A/B/C (X.OFFS_LO) (A: 0x13C, B: 0x228, C: 0x314)

This signed register contains the linearity offset for phase X current channel when the programmable gain amplifier

is set to gain of 32 (that is, the measured current is below the low current threshold). The signed value represented

by this register is added to the current value. The total linearity compensation is applied as follows:

if LINFRM = 0: X.GAIN_LO/214 x

if LINFRM = 1: X.GAIN_LO/214 x (X.IRMS + X.OFFS_LO)

Measurements—RAM Registers

On-Demand RMS Result (N.IRMS) (0x11C)

This register contains the result of the RMS calculation on the AUX channel. Usually, this is the neutral current chan-

nel, but can be defined to be the RMS average of any harmonic of the quantities defined in the AUX_MUX field of the

AUX_CFG register.

XIRMS XOFFS LO.._

216

2+×

Bit: 15 14 13 12 11 10 9 8

Name: Linearity Offset High Byte

Reset: 0x00

Bit: 7 6 5 4 3 2 1 0

Name: Linearity Offset Low Byte

Reset: 0x00

Bit: 31 30 29 28 27 26 25 24

Name: RMS Result, Byte 3

Reset:

Bit: 23 22 21 20 19 18 17 16

Name: RMS Result, Byte 2

Reset:

Bit: 15 14 13 12 11 10 9 8

Name: RMS Result, Byte 1

Reset:

Bit: 7 6 5 4 3 2 1 0

Name: RMS Result, Byte 0

Reset:

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 89

Fundamental Energy

Fundamental Energy Overflow Flags, Phase X = A/B/C (X.EFOVER)

(A: 0x147, B: 0x233, C: 0x31F)

These bits indicate an overflow condition has occurred on a fundamental frequency energy accumulator. An over-

flow condition is not an error condition. Rather, it simply indicates that the value in the energy accumulator could be

smaller than the previous reading due to the overflow in the counter. To obtain the actual energy usage since the

previous reading, 0x100000000 must be added to the difference. These bits, once set, can be cleared only by the

host.

Energy, Fundamental, Real Positive, Phase X = A/B/C (X.EAFPOS)

(A: 0x1FC, B: 0x2E8, C: 0x3D4)

On every DSP cycle, the contents of the X.ACTF register are tested, and if positive, are added to this register. When

this register overflows, the APFOV bit in the X.EFOVER register is set.

BIT NAME FUNCTION

7:5 — Reserved.

4 SFOV When set, indicates an overflow condition on the apparent fundamental-mode energy accumulator.

3 RNFOV When set, indicates an overflow condition on the reactive negative fundamental-mode energy accumulator.

2 RPFOV When set, indicates an overflow condition on the reactive positive fundamental-mode energy accumulator.

1 ANFOV When set, indicates an overflow condition on the real negative fundamental-mode energy accumulator.

0 APFOV When set, indicates an overflow condition on the real positive fundamental-mode energy accumulator.

Bit: 7 6 5 4 3 2 1 0

Name: — — — SFOV RNFOV RPFOV ANFOV APFOV

Reset: 0 0 0 0 0 0 0 0

Bit: 31 30 29 28 27 26 25 24

Name: Real Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Real Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Real Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Real Energy Byte 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

90 ______________________________________________________________________________________

Energy, Fundamental, Real Negative, Phase X = A/B/C (X.EAFNEG)

(A: 0x200, B: 0x2EC, C: 0x3D8)

On every DSP cycle, the contents of the X.ACTF register are tested, and, if negative, absolute values are added to

this register. When this register overflows, the ANFOV bit in the X.EFOVER register is set.

Energy, Fundamental, Reactive Positive, Phase X = A/B/C (X.ERFPOS)

(A: 0x204, B: 0x2F0, C: 0x3DC)

On every DSP cycle, the contents of the X.REAF register are tested, and, if positive, are added to this register. When

this register overflows, the RPFOV bit in the X.EFOVER register is set.

Bit: 31 30 29 28 27 26 25 24

Name: Real Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Real Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Real Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Real Energy Byte 0

Bit: 31 30 29 28 27 26 25 24

Name: Reactive Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Reactive Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Reactive Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Reactive Energy Byte 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 91

Energy, Fundamental, Reactive Negative, Phase X = A/B/C (X.ERFNEG)

(A: 0x208, B: 0x2F4, C: 0x3E0)

On every DSP cycle, the contents of the X.REAF register are tested, and, if negative, absolute values are added to

this register. When this register overflows, the RNFOV bit in the X.EFOVER register is set.

Energy Fundamental, Apparent, Phase X = A/B/C (X.ESF)

(A: 0x20C, B: 0x2F8, C: 0x3E4)

On every DSP cycle, the contents of the X.ESF register are added to this register. When this register overflows, the

SFOV bit in the X.EFOVER register is set. When the MAXQ3180 is operating in low-power mode, energy is not accu-

mulated. However, during low-power mode, current values are accumulated to this register, making this register

accumulate ampere-hours.

Bit: 31 30 29 28 27 26 25 24

Name: Reactive Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Reactive Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Reactive Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Reactive Energy Byte 0

Bit: 31 30 29 28 27 26 25 24

Name: Apparent Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Apparent Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Apparent Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Apparent Energy Byte 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

92 ______________________________________________________________________________________

Energy Accumulated in the Last DSP Cycle

Real Energy, Phase X = A/B/C (X.ACT) (A: 0x1D0, B: 0x2BC, C: 0x3A8)

This signed register provides the raw real energy accumulated over the most recent DSP cycle. For each ADC sam-

ple period, the real instantaneous power calculated from the instantaneous voltage and current is accumulated. At

the end of each DSP cycle, the result of the accumulation over the DSP cycle is copied to this register and is accu-

mulated in X.EAPOS or X.EANEG, depending on the sign of the accumulated energy.

LSB of the energy registers is VFS x IFS x tFR/216.

Reactive Energy, Phase X = A/B/C (X.REA) (A: 0x1D4, B: 0x2C0, C: 0x3AC)

This signed register provides the raw reactive energy accumulated over the most recent DSP cycle. For each ADC

sample period, the reactive instantaneous power calculated from the instantaneous voltage and current is accumu-

lated. At the end of each DSP cycle, the result of the accumulation over the DSP cycle is copied to this register and

is accumulated in X.ERPOS or X.ERNEG, depending on the sign of the accumulated energy.

Bit: 31 30 29 28 27 26 25 24

Name: Real Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Real Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Real Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Real Energy Byte 0

Bit: 31 30 29 28 27 26 25 24

Name: Reactive Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Reactive Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Reactive Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Reactive Energy Byte 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 93

Apparent Energy, Phase X = A/B/C (X.APP) (A: 0x1D8, B: 0x2C4, C: 0x3B0)

This signed register provides the raw apparent energy accumulated over the most recent DSP cycle.

Fundamental Energy Accumulated in the Last DSP Cycle

Fundamental Real Energy, Phase X = A/B/C (X.ACTF) (A: 0x1DC, B: 0x2C8, C: 0x3B4)

This signed register accumulates energy in the same fashion as the X.ACT register, but only at the fundamental line

frequency.

Bit: 31 30 29 28 27 26 25 24

Name: Apparent Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Apparent Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Apparent Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Apparent Energy Byte 0

Bit: 31 30 29 28 27 26 25 24

Name: Real Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Real Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Real Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Real Energy Byte 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

94 ______________________________________________________________________________________

Fundamental Reactive Energy, Phase X = A/B/C (X.REAF) (A: 0x1E0, B: 0x2CC, C: 0x3B8)

This signed register accumulates energy in the same fashion as the X.REA register, but only at the fundamental line

frequency.

Fundamental Apparent Energy, Phase X = A/B/C (X.APPF) (A: 0x1E4, B: 0x2D0, C: 0x3BC)

This register accumulates energy in the same fashion as the X.APP register, but only at the fundamental line frequency.

Bit: 31 30 29 28 27 26 25 24

Name: Reactive Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Reactive Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Reactive Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Reactive Energy Byte 0

Bit: 31 30 29 28 27 26 25 24

Name: Apparent Energy Byte 3

Bit: 23 22 21 20 19 18 17 16

Name: Apparent Energy Byte 2

Bit: 15 14 13 12 11 10 9 8

Name: Apparent Energy Byte 1

Bit: 7 6 5 4 3 2 1 0

Name: Apparent Energy Byte 0

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 95

Checksum (CHKSUM) (0x060)

This register contains the calculated 16-bit arithmetic checksum over critical configuration and calibration registers.

It is updated on every DSP cycle. In use, the administrative processor records the value in the CHKSUM register and

then checks it periodically to verify that no configuration or calibration registers have changed. The MAXQ3180 sets

the CHSCH bit when this register’s value changes.

The registers included in the checksum calculation include the following:

Bit: 15 14 13 12 11 10 9 8

Name: Checksum High Byte

Reset:

Bit: 7 6 5 4 3 2 1 0

Name: Checksum Low Byte

Reset:

SYS_KHZ THR2 R_ADCRATE A.I_GAIN B.I_GAIN C.I_GAIN

VOLT_CC REJ_NS R_ADCACQ A.V_GAIN B.V_GAIN C.V_GAIN

AMP_CC AVG_NS R_SPICF A.E_GAIN B.E_GAIN C.E_GAIN

PWR_CC AVG_C NZX_TIMO A.EF_GAIN B.EF_GAIN C.EF_GAIN

ENR_CC HPF_C COM_TIMO A.OFFS_HI B.OFFS_HI C.OFFS_HI

CYCNT B0FUND ACC_TIMO A.GAIN_LO B.GAIN_LO C.GAIN_LO

PLSCFG1 OCLVL I1THR A.OFFS_LO B.OFFS_LO C.OFFS_LO

PLSCFG2 OVLVL I2THR A.PA0 B.PA0 C.PA0

PLS1_WD UVLVL ZC_LPF A.PA1 B.PA1 C.PA1

THR1 NOLOAD A.PA2 B.PA2 C.PA2

PLS2_WD R_ACFG

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

96 ______________________________________________________________________________________

Measurements—Virtual Registers

Fundamental Real Power, Phase A/B/C/T (PWRPF.X)

(A: 0x881, B: 0x882, C: 0x884, T: 0x887)

This signed register contains the real instantaneous power delivered into phase A/B/C or total at the fundamental line

frequency only. Power is calculated from the instantaneous energy measurement according to the following equation:

Fundamental Reactive Power, Phase A/B/C/T (PWRQF.X)

(A: 0x891, B: 0x892, C: 0x894, T: 0x897)

This signed register contains the reactive instantaneous power delivered into phase A/B/C or total at the fundamental

line frequency only. Power is calculated from the instantaneous energy measurement according to the following

equation:

PWRQF X XREAF PWR CC

.._

=××216

PWRPF X X ACTF PWR CC

.._

=××216

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 97

Fundamental Apparent Power, Phase A/B/C/T (PWRSF.X)

(A: 0x8A1, B: 0x8A2, C: 0x8A4, T: 0x8A7)

This register contains the instantaneous apparent power delivered into phase A/B/C or total at the fundamental line

frequency only. Power is calculated from the instantaneous energy measurement according to the following equation:

Fundamental Real Energy, Phase A/B/C/T (ENRPF.X)

(A: 0x8E1, B: 0x8E2, C: 0x8E4, T: 0x8E7)

This signed register contains the real accumulated energy delivered into phase A/B/C or total. The register is calcu-

lated according to the following formula:

ENRPF.X = ENR_CC x (X.EAFPOS - X.EAFNEG)

Fundamental Reactive Energy, Phase A/B/C/T (ENRQF.X)

(A: 0x8F1, B: 0x8F2, C: 0x8F4, T: 0x8F7)

This signed register contains the reactive accumulated energy delivered into phase A/B/C or total. The register is

calculated according to the following formula:

ENRQF.X = ENR_CC x (X.ERFPOS - X.ERFNEG)

Fundamental Apparent Energy, Phase A/B/C/T (ENRSF.X)

(A: 0x8B1, B: 0x8B2, C: 0x8B4, T: 0x8B7)

This register contains the apparent accumulated energy delivered into phase A/B/C or total. The register is the prod-

uct of the ENR_CC and X.ESF registers.

PWRSF X X APPF PWR CC

.._

=××216

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

Byte 7 (MSByte unused) Byte 6 (unused)

Byte 5 Byte 4

Byte 3 Byte 2

Byte 1 Byte 0 (LSByte)

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

98 ______________________________________________________________________________________

Phasors

Phase B Phasor (VBPH: 0x852)

This register reports phase angle of voltage phase B

with respect to voltage phase A. The value is

expressed in units of 0.01 degree; thus, the nominal

value is 12000 decimal (0x2EE0). This value is calculat-

ed based on zero-crossing detection. It may exhibit

noticable error in the presence of harmonics on voltage

channels. This register is 2 bytes wide.

Phase C Phasor (VCPH: 0x854)

This register reports phase angle of voltage phase C

with respect to voltage phase A. The value is

expressed in units of 0.01 degree; thus, the nominal

value is 24000 decimal (0x5DC0). This value is calcu-

lated based on zero-crossing detection. It may exhibit

noticable error in the presence of harmonics on voltage

channels. This register is 2 bytes wide.

Harmonics

RMS Voltage, Harmonic (V.HARM) (0x830)

This register reports the RMS voltage. The units are

defined by the VOLT_CC setting. Use AUX_CFG to

configure the phase (A/B/C) and harmonic order

desired.

RMS Current, Harmonic/Neutral (I.N, I.HARM) (0x840)

This register reports the harmonic RMS current of

selected phase (A/B/C) and harmonic order, harmonic,

or the RMS current of the neutral current channel. The

units are defined by the AMP_CC setting. Use

AUX_CFG to configure the phase (A/B/C) and harmonic

order desired.

Ratio of Harmonic/Fundamental (HARM_NF) (0x850)

This register reports the ratio of the selected harmonic

RMS over the fundamental RMS of the same signal

(except IN). The master must configure the AUX_CFG

and select AUX_MUX before reading this register. This

Special Commands

Table 7 shows the read-only virtual registers that acti-

vate special commands when read by the master.

Some commands return dummy values.

Applications Information

Grounds and Bypassing

Careful PCB layout significantly minimizes noise on the

analog inputs, resulting in less noise on the digital I/O

that could cause improper operation. The use of multi-

layer boards is essential to allow the use of dedicated

power planes. The area under any digital components

should be a continuous ground plane if possible. Keep

any bypass capacitor leads short for best noise rejec-

tion and place the capacitors as close to the leads of

the devices as possible.

The MAXQ3180 must have separate ground areas for

the analog (AGND) and digital (DGND) portions, con-

nected together at a single point.

NAME ADDRESS DESCRIPTION

DATA

LENGTH

(BYTES)

UPD_SFR 0x900

Reading this register copies the mirror registers (R_ADCF, R_ADCRATE,

R_ADCACQ, R_SPICF) into hardware SFR registers. The read returns dummy data. 1

UPD_MIR 0xA00

Reading this register copies hardware SFR registers into mirror registers (R_ADCF,

R_ADCRATE, R_ADCACQ, R_SPICF). The read returns dummy data. 1

DSPVER 0xC00 Reading this register returns the DSP firmware version number. 2

RAWTEMP 0xC01

Reading this register initiates the sampling and averaging of two internal

temperature readings. The result in internal temperature units is read from this

Celsius: T[c] = T[raw] x TempFactor - 273.15

where TempFactor is a value to be determined by calibration. Note that the final

value may be slightly higher than ambient due to internal die heating.

ENTER STOP 0xC02 Reading this register places the device into Stop Mode. 1

ENTER LOWPM 0xC03 Reading this register places the device into LOWPM Mode. 1

EXIT LOWPM 0xC04 Reading this register exits LOWPM Mode. 1

Table 7. Virtual Registers That Activate Special Commands

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

______________________________________________________________________________________ 99

Package Information

For the latest package outline information and land patterns, go to www.maxim-ic.com/packages.

CMOS design guidelines for any semiconductor require

that no pin be taken above DVDD or below DGND.

Violation of this guideline can result in a hard failure

(damage to the silicon inside the device) or a soft fail-

ure (unintentional modification of memory contents).

Voltage spikes above or below the device’s absolute

maximum ratings can potentially cause a devastating

IC latchup.

Microcontrollers commonly experience negative volt-

age spikes through either their power pins or general-

purpose I/O pins. Negative voltage spikes on power

pins are especially problematic as they directly couple

to the internal power buses. Devices such as keypads

can conduct electrostatic discharges directly into the

microcontroller and seriously damage the device.

System designers must protect components against

these transients that can corrupt system memory.

Specific Design Considerations for

MAXQ3180-Based Systems

To reduce the possibility of coupling noise into the

microcontroller, the system should be designed with a

crystal or oscillator in a metal case that is grounded to

the digital plane. Doing so reduces the susceptibility of

the design to fast transient noise.

Because the MAXQ3180 is designed for use in systems

where high voltages are present, care must be taken to

route all signal paths, both analog and digital, as far

away as possible from the high-voltage components.

It is possible to construct more elaborate metering

designs using multiple MAXQ3180 devices. This can be

accomplished by using a single SPI bus to connect all

the MAXQ3180 devices together but using separate

slave select lines to individually select each MAXQ3180.

Additional Documentation

Designers must ensure they have the latest MAXQ3180

errata documents. Errata sheets contain deviations

from published specifications. A MAXQ3180 errata

sheet for any specific device revision is available at

www.maxim-ic.com/errata.

Technical Support

For technical support, go to https://support.maxim-

ic.com/micro.

PACKAGE TYPE PACKAGE CODE DOCUMENT NO.

28 TSSOP U28+3 21-0066

TOP VIEW

MAXQ3180

TSSOP

254 AVDDI0N

263 V0PI0P

272 V1P

INP

281 V2PVN

227 DVDD

I2P

236 VCOMMI1N

218 RESETI2N

209 CFQAGND

1910 CFPXTAL2

1811 DGNDXTAL1

1712 DVDDIRQ

1613 MISOSSEL

245 VREF

I1P

1514 MOSISCLK

Pin Configuration

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

100 _____________________________________________________________________________________

MAXQ3180

V0P

SSEL

SCLK

MOSI

MISO

V1P

V2P

VCOMM

I0P

I0N

I1P

I1N

I2P

I2N

VOLTAGE SENSE

CURRENT TRANSFORMER

MASTER

Typical Application Circuit

MAXQ3180

Low-Power, Multifunction, Polyphase AFE

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are

implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.

Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ___________________

101

Revision History

REVISION

NUMBER

REVISION

DATE DESCRIPTION PAGES

CHANGED

0 2/08 Initial release. —

1 1/09 Updated data sheet to be consistent with additional device features. All

Removed reference to the device supporting IEC standards in the Features section;

changed the precision internal voltage reference spec from 1.23V to 2.048V. 1

In the Electrical Characteristics table, changed stop-mode current TYP and MAX from

1μA and 0μA to 0.2μA and 12μA, respectively; changed the input voltage range MAX

from 2V to VREF V; added VREF to output voltage SYMBOL; changed the tSCH and tSCL

MIN to 4 x tSYS and added Note 3 to CONDITIONS; changed the output voltage spec

for the internal voltage reference from 1.23V (typ) to 2.048V (typ); changed the

maximum SPI clock rate spec for the SPI slave-mode interface timing from 2MHz

(max) to fSYS/4MHz (max), and changed the tSE, tSD, tSIS, tSIH, and tSOV specs;

updated the SPI Slave Mode Timing diagram.

10, 11, 12

Updated the CFP and CFQ descriptions in the Pin Description table. 14

Removed statement about the IRQ line dropping low when reset causes the device

to enter Initialization Mode in the Watchdog Reset section. 17

Added new paragraph to the Host Software Design section about reading the virtual

registers. 24

Removed the Code Examples section. 26, 27, 28

Updated the bit functions for PORF and WDTR in the Global Status Register (STATUS)

(0x000) section. 28

Added bit 14 functionality (DSPRDY) to the IRQ_FLAG register. 33

Added bit 14 functionality (EDSPRDY) to the IRQ_MASK register and updated the

EDSPOR function description. 34

Corrected the reset valued for the OCLVL, OVLVL, and SYS_KHZ registers. 40, 41, 77

Corrected the reference of V/A to A/V in the Units Conversion Examples section

current transducer ratio (ITR) equation. 65

Updated the bit description for ADCMX (SCAN_IX.7:4, SCAN_VX.7:4, SCAN_IN.7:4)

and PGG. 73, 74

Updated the descriptions of the SCAN_IN and SCAN_TE registers. 75, 76

Corrected the reset value to 1 for bit 8 in the R_ADCRATE register. 83

2 8/09

Updated the phase B phasor and phase C phasor nominal values. 98

Changed the voltage range on VxP, IxN relative to AGND to -0.3V to +4.0V in the

Absolute Maximum Ratings section. 10

3 12/09

Added a statement that the CRC be enabled for read and write in the Host Software

Design section. 24