LM4765 www.ti.com SNAS030C - AUGUST 1998 - REVISED APRIL 2013 LM4765 OvertureTM Audio Power Amplifier Series Dual 30W Audio Power Amplifier with Mute and Standby Modes Check for Samples: LM4765 FEATURES DESCRIPTION * * The LM4765 is a stereo audio amplifier capable of delivering typically 30W per channel of continuous average output power into an 8 load with less than 0.1% THD+N. 1 23 * * * * SPiKe Protection Minimal Amount of External Components Necessary Quiet Fade-In/Out Mute Mode Standby-Mode Non-Isolated 15-Lead TO-220 Package Wide Supply Range 20V - 66V KEY SPECIFICATIONS * * * THD+N at 1kHz at 2 x 25W Continuous Average Output Power into 8: 0.1% (max) THD+N at 1kHz at Continuous Average Output Power of 2 x 30W into 8: 0.009% (typ) Standby Current: 6.5mA (typ) Each amplifier has an independent smooth transition fade-in/out mute and a power conserving standby mode which can be controlled by external logic. The performance of the LM4765, utilizing its Self Peak Instantaneous Temperature (Ke) (SPiKe) protection circuitry, places it in a class above discrete and hybrid amplifiers by providing an inherently, dynamically protected Safe Operating Area (SOA). SPiKe protection means that these parts are safeguarded at the output against overvoltage, undervoltage, overloads, including thermal runaway and instantaneous temperature peaks. APPLICATIONS * * * High-End Stereo TVs Component Stereo Compact Stereo TYPICAL APPLICATION Numbers in parentheses represent pinout for amplifier B. *Optional component dependent upon specific design requirements. Figure 1. Typical Audio Amplifier Application Circuit 1 2 3 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Overture is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1998-2013, Texas Instruments Incorporated LM4765 SNAS030C - AUGUST 1998 - REVISED APRIL 2013 www.ti.com CONNECTION DIAGRAM Figure 2. Plastic Package - Top View Non-Isolated Package See Package Number NDL0015A These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ABSOLUTE MAXIMUM RATINGS (1) (2) (3) Supply Voltage |VCC| + |VEE| (No Input) 66V Supply Voltage |VCC| + |VEE| (with Input) 64V (VCC or VEE) and |VCC| + |VEE| 60V Common Mode Input Voltage Differential Input Voltage 60V Output Current Internally Limited Power Dissipation (4) ESD Susceptability 62.5W (5) 2000V Junction Temperature (6) 150C Thermal Resistance Non-Isolated NDL-Package Soldering Information NDL Package (10 sec.) JC (3) (4) (5) (6) 260C -40C to +150C Storage Temperature (1) (2) 1C/W All voltages are measured with respect to the GND pins (5, 10), unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. For operating at case temperatures above 25C, the device must be derated based on a 150C maximum junction temperature and a thermal resistance of JC = 1C/W for the NDL package. Refer to the section DETERMINING THE CORRECT HEAT SINK. Human body model, 100 pF discharged through a 1.5 k resistor. The operating junction temperature maximum is 150C, however, the instantaneous Safe Operating Area temperature is 250C. OPERATING RATINGS (1) (2) Temperature Range TMIN TA TMAX -20C TA +85C Supply Voltage |VCC| + |VEE| (3) (1) (2) (3) 2 20V to 64V All voltages are measured with respect to the GND pins (5, 10), unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. Operation is ensured up to 64V, however, distortion may be introduced from SPiKe Protection Circuitry if proper thermal considerations are not taken into account. Refer to the APPLICATION INFORMATION section for a complete explanation. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 LM4765 www.ti.com SNAS030C - AUGUST 1998 - REVISED APRIL 2013 ELECTRICAL CHARACTERISTICS (1) (2) The following specifications apply for VCC = +28V, VEE = -28V with RL = 8 unless otherwise specified. Limits apply for TA = 25C. Symbol |VCC| + Parameter Conditions Power Supply Voltage (5) GND - VEE 9V LM4765 Limit (4) 18 20 V (min) 64 V (max) |VEE| PO (6) THD + N Output Power (Continuous Average) Total Harmonic Distortion Plus Noise Units (Limits) Typical (3) THD + N = 0.1% (max), f = 1 kHz |VCC| = |VEE| = 28V, RL = 8 30 25 W/ch (min) |VCC| = |VEE| = 20V, RL = 4 22 15 W/ch (min) 30 W/ch, RL = 8 0.08 % 15 W/ch, RL = 4, |VCC| = |VEE| = 20V 0.1 % dB 20 Hz f 20 kHz, AV = 26 dB Xtalk SR (6) Itotal (7) Channel Separation f = 1 kHz, VO = 10.9 Vrms 80 Slew Rate VIN = 1.414 Vrms, trise = 2 ns 18 12 V/s (min) Total Quiescent Power Both Amplifiers VCM = 0V, Supply Current VO = 0V, IO = 0 mA Standby: Off 50 80 mA (max) Standby: On 6.5 8 mA (max) VOS (7) Input Offset Voltage VCM = 0V, IO = 0 mA 2.0 15 mV (max) IB Input Bias Current VCM = 0V, IO = 0 mA 0.2 0.5 A (max) IOS Input Offset Current VCM = 0V, IO = 0 mA 0.002 0.2 A (max) IO Output Current Limit |VCC| = |VEE| = 10V, tON = 10 ms, 3.5 2.9 Apk (min) |VCC-VO|, VCC = 20V, IO = +100 mA 1.8 2.3 V (max) |VO-VEE|, VEE = -20V, IO = -100 mA 2.5 3.2 V (max) VCC = 30V to 10V, VEE = -30V, 115 85 dB (min) 110 85 dB (min) 110 80 dB (min) VO = 0V VOD (7) PSRR (7) Output Dropout Voltage (8) Power Supply Rejection Ratio VCM = 0V, IO = 0 mA VCC = 30V, VEE = -30V to -10V VCM = 0V, IO = 0 mA CMRR (7) Common Mode Rejection Ratio AVOL (7) Open Loop Voltage Gain RL = 2 k, VO = 30V 110 90 dB (min) GBWP Gain Bandwidth Product fO = 100 kHz, VIN = 50 mVrms 7.5 5 MHz (min) eIN (6) Input Noise IHF--A Weighting Filter 2.0 8 V (max) VCC = 35V to 10V, VEE = -10V to -35V, VCM = 10V to -10V, IO = 0 mA RIN = 600 (Input Referred) (1) (2) (3) (4) (5) (6) (7) (8) All voltages are measured with respect to the GND pins (5, 10), unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. Typicals are measured at 25C and represent the parametric norm. Limits are specifications that all parts are tested in production to meet the stated values. VEE must have at least -9V at its pin with reference to ground in order for the under-voltage protection circuitry to be disabled. In addition, the voltage differential between VCC and VEE must be greater than 14V. AC Electrical Test; Refer to TEST CIRCUIT #2 . DC Electrical Test; Refer to TEST CIRCUIT #1. The output dropout voltage, VOD, is the supply voltage minus the clipping voltage. Refer to the Clipping Voltage vs. Supply Voltage graph in the TYPICAL PERFORMANCE CHARACTERISTICS section. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 3 LM4765 SNAS030C - AUGUST 1998 - REVISED APRIL 2013 www.ti.com ELECTRICAL CHARACTERISTICS(1)(2) (continued) The following specifications apply for VCC = +28V, VEE = -28V with RL = 8 unless otherwise specified. Limits apply for TA = 25C. Symbol Parameter Conditions LM4765 Typical (3) SNR Signal-to-Noise Ratio PO = 1W, A--Weighted, Limit (4) Units (Limits) 98 dB 108 dB Measured at 1 kHz, RS = 25 PO = 25W, A--Weighted Measured at 1 kHz, RS = 25 AM Mute Attenuation Pin 6,11 at 2.5V VIL Standby Low Input Voltage Not in Standby Mode VIH Standby High Input Voltage In Standby Mode VIL Mute Low Input Voltage Outputs Not Muted VIH Mute High Input Voltage Outputs Muted 115 80 dB (min) 0.8 V (max) 2.5 V (min) 0.8 V (max) 2.5 V (min) Standby Pin 2.0 Mute pin 2.0 TEST CIRCUIT #1 DC Electrical Test; Refer to TEST CIRCUIT #1 Figure 3. DC Electrical Test Circuit 4 Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 LM4765 www.ti.com SNAS030C - AUGUST 1998 - REVISED APRIL 2013 TEST CIRCUIT #2 AC Electrical Test; Refer to TEST CIRCUIT #2 . Figure 4. AC Electrical Test Circuit Bridged Amplifier Application Circuit Figure 5. Bridged Amplifier Application Circuit Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 5 LM4765 SNAS030C - AUGUST 1998 - REVISED APRIL 2013 www.ti.com Single Supply Application Circuit Note: *Optional components dependent upon specific design requirements. Figure 6. Single Supply Amplifier Application Circuit Auxiliary Amplifier Application Circuit Figure 7. Special Audio Amplifier Application Circuit 6 Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 LM4765 www.ti.com SNAS030C - AUGUST 1998 - REVISED APRIL 2013 Equivalent Schematic (excluding active protection circuitry) Figure 8. LM4765 (One Channel Only) Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 7 LM4765 SNAS030C - AUGUST 1998 - REVISED APRIL 2013 www.ti.com EXTERNAL COMPONENTS DESCRIPTION Components RB Prevents currents from entering the amplifier's non-inverting input which may be passed through to the load upon power down of the system due to the low input impedance of the circuitry when the undervoltage circuitry is off. This phenomenon occurs when the supply voltages are below 1.5V. 2 Ri Inverting input resistance to provide AC gain in conjunction with Rf. 3 Rf Feedback resistance to provide AC gain in conjunction with Ri. 4 Ci (1) Feedback capacitor which ensures unity gain at DC. Also creates a highpass filter with Ri at fC = 1/(2RiCi). 5 CS Provides power supply filtering and bypassing. Refer to the application section for proper placement and selection of bypass capacitors. 6 RV (1) (1) Acts as a volume control by setting the input voltage level. 7 RIN 8 CIN (1) Input capacitor which blocks the input signal's DC offsets from being passed onto the amplifier's inputs. 9 RSN (1) Works with CSN to stabilize the output stage by creating a pole that reduces high frequency instabilities. (1) 10 CSN 11 L (1) 12 R (1) 13 RA 14 CA Sets the amplifier's input terminals DC bias point when CIN is present in the circuit. Also works with CIN to create a highpass filter at fC = 1/(2RINCIN). Refer to Figure 7. Works with RSN to stabilize the output stage by creating a pole that reduces high frequency instabilities. The pole is set at fC = 1/(2RSNCSN). Refer to Figure 7. Provides high impedance at high frequencies so that R may decouple a highly capacitive load and reduce the Q of the series resonant circuit. Also provides a low impedance at low frequencies to short out R and pass audio signals to the load. Refer to Figure 7. Provides DC voltage biasing for the transistor Q1 in single supply operation. Provides bias filtering for single supply operation. (1) 15 RINP 16 RBI Provides input bias current for single supply operation. Refer to the CLICKS AND POPS application section for a more detailed explanation of the function of RBI. 17 RE Establishes a fixed DC current for the transistor Q1 in single supply operation. This resistor stabilizes the halfsupply point along with CA. (1) 8 Functional Description 1 Limits the voltage difference between the amplifier's inputs for single supply operation. Refer to the CLICKS AND POPS application section for a more detailed explanation of the function of RINP. Optional components dependent upon specific design requirements. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 LM4765 www.ti.com SNAS030C - AUGUST 1998 - REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS THD + N vs Frequency THD + N vs Frequency Figure 9. Figure 10. THD + N vs Frequency THD + N vs Output Power Figure 11. Figure 12. THD + N vs Output Power THD + N vs Output Power Figure 13. Figure 14. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 9 LM4765 SNAS030C - AUGUST 1998 - REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) 10 Clipping Voltage vs Supply Voltage Clipping Voltage vs Supply Voltage Figure 15. Figure 16. Clipping Voltage vs Supply Voltage Output Power vs Load Resistance Figure 17. Figure 18. Power Dissipation vs Output Power Power Dissipation vs Output Power Figure 19. Figure 20. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 LM4765 www.ti.com SNAS030C - AUGUST 1998 - REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Output Power vs Supply Voltage Output Mute vs Mute Pin Voltage Figure 21. Figure 22. Output Mute vs Mute Pin Voltage Channel Separation vs Frequency Figure 23. Figure 24. Pulse Response Large Signal Response Figure 25. Figure 26. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 11 LM4765 SNAS030C - AUGUST 1998 - REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) 12 Power Supply Rejection Ratio Common-Mode Rejection Ratio Figure 27. Figure 28. Open Loop Frequency Response Safe Area Figure 29. Figure 30. SPiKe Protection Response Supply Current vs Supply Voltage Figure 31. Figure 32. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 LM4765 www.ti.com SNAS030C - AUGUST 1998 - REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Pulse Thermal Resistance Pulse Thermal Resistance Figure 33. Figure 34. Supply Current vs Output Voltage Pulse Power Limit Figure 35. Figure 36. Pulse Power Limit Supply Current vs Case Temperature Figure 37. Figure 38. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 13 LM4765 SNAS030C - AUGUST 1998 - REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Supply Current (ICC) vs Standby Pin Voltage Supply Current (IEE) vs Standby Pin Voltage Figure 39. Figure 40. Input Bias Current vs Case Temperature Figure 41. 14 Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 LM4765 www.ti.com SNAS030C - AUGUST 1998 - REVISED APRIL 2013 APPLICATION INFORMATION MUTE MODE By placing a logic-high voltage on the mute pins, the signal going into the amplifiers will be muted. If the mute pins are left floating or connected to a logic-low voltage, the amplifiers will be in a non-muted state. There are two mute pins, one for each amplifier, so that one channel can be muted without muting the other if the application requires such a configuration. Refer to the TYPICAL PERFORMANCE CHARACTERISTICS section for curves concerning Mute Attenuation vs Mute Pin Voltage. STANDBY MODE The standby mode of the LM4765 allows the user to drastically reduce power consumption when the amplifiers are idle. By placing a logic-high voltage on the standby pins, the amplifiers will go into Standby Mode. In this mode, the current drawn from the VCC supply is typically less than 10 A total for both amplifiers. The current drawn from the VEE supply is typically 4.2 mA. Clearly, there is a significant reduction in idle power consumption when using the standby mode. There are two Standby pins, so that one channel can be put in standby mode without putting the other amplifier in standby if the application requires such flexibility. Refer to the TYPICAL PERFORMANCE CHARACTERISTICS section for curves showing Supply Current vs. Standby Pin Voltage for both supplies. UNDER-VOLTAGE PROTECTION Upon system power-up, the under-voltage protection circuitry allows the power supplies and their corresponding capacitors to come up close to their full values before turning on the LM4765 such that no DC output spikes occur. Upon turn-off, the output of the LM4765 is brought to ground before the power supplies such that no transients occur at power-down. OVER-VOLTAGE PROTECTION The LM4765 contains over-voltage protection circuitry that limits the output current to approximately 3.5 Apk while also providing voltage clamping, though not through internal clamping diodes. The clamping effect is quite the same, however, the output transistors are designed to work alternately by sinking large current spikes. SPiKe PROTECTION The LM4765 is protected from instantaneous peak-temperature stressing of the power transistor array. The Safe Operating graph in the TYPICAL PERFORMANCE CHARACTERISTICS section shows the area of device operation where SPiKe Protection Circuitry is not enabled. The waveform to the right of the SOA graph exemplifies how the dynamic protection will cause waveform distortion when enabled. Please refer to AN-898 for more detailed information. THERMAL PROTECTION The LM4765 has a sophisticated thermal protection scheme to prevent long-term thermal stress of the device. When the temperature on the die reaches 165C, the LM4765 shuts down. It starts operating again when the die temperature drops to about 155C, but if the temperature again begins to rise, shutdown will occur again at 165C. Therefore, the device is allowed to heat up to a relatively high temperature if the fault condition is temporary, but a sustained fault will cause the device to cycle in a Schmitt Trigger fashion between the thermal shutdown temperature limits of 165C and 155C. This greatly reduces the stress imposed on the IC by thermal cycling, which in turn improves its reliability under sustained fault conditions. Since the die temperature is directly dependent upon the heat sink used, the heat sink should be chosen such that thermal shutdown will not be reached during normal operation. Using the best heat sink possible within the cost and space constraints of the system will improve the long-term reliability of any power semiconductor device, as discussed in the DETERMINING THE CORRECT HEAT SINK Section. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 15 LM4765 SNAS030C - AUGUST 1998 - REVISED APRIL 2013 www.ti.com DETERMlNlNG MAXIMUM POWER DISSIPATION Power dissipation within the integrated circuit package is a very important parameter requiring a thorough understanding if optimum power output is to be obtained. An incorrect maximum power dissipation calculation may result in inadequate heat sinking causing thermal shutdown and thus limiting the output power. Equation 1 exemplifies the theoretical maximum power dissipation point of each amplifier where VCC is the total supply voltage. PDMAX = VCC2/22RL (1) Thus by knowing the total supply voltage and rated output load, the maximum power dissipation point can be calculated. The package dissipation is twice the number which results from Equation 1 since there are two amplifiers in each LM4765. Refer to the graphs of Power Dissipation versus Output Power in the TYPICAL PERFORMANCE CHARACTERISTICS section which show the actual full range of power dissipation not just the maximum theoretical point that results from Equation 1. DETERMINING THE CORRECT HEAT SINK The choice of a heat sink for a high-power audio amplifier is made entirely to keep the die temperature at a level such that the thermal protection circuitry does not operate under normal circumstances. The thermal resistance from the die (junction) to the outside air (ambient) is a combination of three thermal resistances, JC, CS, and SA. In addition, the thermal resistance, JC (junction to case), of the LM4765 is 1C/W. Using Thermalloy Thermacote thermal compound, the thermal resistance, CS (case to sink), is about 0.2C/W. Since convection heat flow (power dissipation) is analogous to current flow, thermal resistance is analogous to electrical resistance, and temperature drops are analogous to voltage drops, the power dissipation out of the LM4765 is equal to the following: PDMAX = (TJMAX-TAMB)/JA where * * TJMAX = 150C, TAMB is the system ambient temperature JA = JC + CS + SA (2) Once the maximum package power dissipation has been calculated using Equation 1, the maximum thermal resistance, SA, (heat sink to ambient) in C/W for a heat sink can be calculated. This calculation is made using Equation 3 which is derived by solving for SA in Equation 2. SA = [(TJMAX-TAMB)-PDMAX(JC +CS)]/PDMAX (3) Again it must be noted that the value of SA is dependent upon the system designer's amplifier requirements. If the ambient temperature that the audio amplifier is to be working under is higher than 25C, then the thermal resistance for the heat sink, given all other things are equal, will need to be smaller. SUPPLY BYPASSING The LM4765 has excellent power supply rejection and does not require a regulated supply. However, to improve system performance as well as eliminate possible oscillations, the LM4765 should have its supply leads bypassed with low-inductance capacitors having short leads that are located close to the package terminals. Inadequate power supply bypassing will manifest itself by a low frequency oscillation known as "motorboating" or by high frequency instabilities. These instabilities can be eliminated through multiple bypassing utilizing a large tantalum or electrolytic capacitor (10 F or larger) which is used to absorb low frequency variations and a small ceramic capacitor (0.1 F) to prevent any high frequency feedback through the power supply lines. If adequate bypassing is not provided, the current in the supply leads which is a rectified component of the load current may be fed back into internal circuitry. This signal causes distortion at high frequencies requiring that the supplies be bypassed at the package terminals with an electrolytic capacitor of 470 F or more. 16 Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 LM4765 www.ti.com SNAS030C - AUGUST 1998 - REVISED APRIL 2013 BRIDGED AMPLIFIER APPLICATION The LM4765 has two operational amplifiers internally, allowing for a few different amplifier configurations. One of these configurations is referred to as "bridged mode" and involves driving the load differentially through the LM4765's outputs. This configuration is shown in Figure 5. Bridged mode operation is different from the classical single-ended amplifier configuration where one side of its load is connected to ground. A bridge amplifier design has a distinct advantage over the single-ended configuration, as it provides differential drive to the load, thus doubling output swing for a specified supply voltage. Consequently, theoretically four times the output power is possible as compared to a single-ended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited or clipped. A direct consequence of the increased power delivered to the load by a bridge amplifier is an increase in internal power dissipation. For each operational amplifier in a bridge configuration, the internal power dissipation will increase by a factor of two over the single ended dissipation. Thus, for an audio power amplifier such as the LM4765, which has two operational amplifiers in one package, the package dissipation will increase by a factor of four. To calculate the LM4765's maximum power dissipation point for a bridged load, multiply Equation 1 by a factor of four. This value of PDMAX can be used to calculate the correct size heat sink for a bridged amplifier application. Since the internal dissipation for a given power supply and load is increased by using bridged-mode, the heatsink's SA will have to decrease accordingly as shown by Equation 3. Refer to the section, DETERMINING THE CORRECT HEAT SINK, for a more detailed discussion of proper heat sinking for a given application. SINGLE-SUPPLY AMPLIFIER APPLICATION The typical application of the LM4765 is a split supply amplifier. But as shown in Figure 6, the LM4765 can also be used in a single power supply configuration. This involves using some external components to create a halfsupply bias which is used as the reference for the inputs and outputs. Thus, the signal will swing around halfsupply much like it swings around ground in a split-supply application. Along with proper circuit biasing, a few other considerations must be accounted for to take advantage of all of the LM4765 functions. The LM4765 possesses a mute and standby function with internal logic gates that are half-supply referenced. Thus, to enable either the Mute or Standby function, the voltage at these pins must be a minimum of 2.5V above half-supply. In single-supply systems, devices such as microprocessors and simple logic circuits used to control the mute and standby functions, are usually referenced to ground, not half-supply. Thus, to use these devices to control the logic circuitry of the LM4765, a "level shifter," like the one shown in Figure 42, must be employed. A level shifter is not needed in a split-supply configuration since ground is also half-supply. Figure 42. Level Shift Circuit When the voltage at the Logic Input node is 0V, the 2N3904 is "off" and thus resistor Rc pulls up mute or standby input to the supply. This enables the mute or standby function. When the Logic Input is 5V, the 2N3904 is "on" and consequently, the voltage at the collector is essentially 0V. This will disable the mute or standby function, and thus the amplifier will be in its normal mode of operation. Rshift, along with Cshift, creates an RC time constant that reduces transients when the mute or standby functions are enabled or disabled. Additionally, Rshift limits the current supplied by the internal logic gates of the LM4765 which insures device reliability. Refer to the MUTE MODE and STANDBY MODE sections in the APPLICATION INFORMATION section for a more detailed description of these functions. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 17 LM4765 SNAS030C - AUGUST 1998 - REVISED APRIL 2013 www.ti.com CLICKS AND POPS In the typical application of the LM4765 as a split-supply audio power amplifier, the IC exhibits excellent "click" and "pop" performance when utilizing the mute and standby modes. In addition, the device employs UnderVoltage Protection, which eliminates unwanted power-up and power-down transients. The basis for these functions are a stable and constant half-supply potential. In a split-supply application, ground is the stable halfsupply potential. But in a single-supply application, the half-supply needs to charge up just like the supply rail, VCC. This makes the task of attaining a clickless and popless turn-on more challenging. Any uneven charging of the amplifier inputs will result in output clicks and pops due to the differential input topology of the LM4765. To achieve a transient free power-up and power-down, the voltage seen at the input terminals should be ideally the same. Such a signal will be common-mode in nature, and will be rejected by the LM4765. In Figure 6, the resistor RINP serves to keep the inputs at the same potential by limiting the voltage difference possible between the two nodes. This should significantly reduce any type of turn-on pop, due to an uneven charging of the amplifier inputs. This charging is based on a specific application loading and thus, the system designer may need to adjust these values for optimal performance. As shown in Figure 6, the resistors labeled RBI help bias up the LM4765 off the half-supply node at the emitter of the 2N3904. But due to the input and output coupling capacitors in the circuit, along with the negative feedback, there are two different values of RBI, namely 10 k and 200 k. These resistors bring up the inputs at the same rate resulting in a popless turn-on. Adjusting these resistors values slightly may reduce pops resulting from power supplies that ramp extremely quick or exhibit overshoot during system turn-on. AUDIO POWER AMPLlFIER DESIGN Design a 15W/8 Audio Amplifier Given: Power Output 15 Wrms Load Impedance 8 Input Level 1 Vrms(max) Input Impedance 47 k Bandwidth 20 Hz-20 kHz 0.25 dB A designer must first determine the power supply requirements in terms of both voltage and current needed to obtain the specified output power. VOPEAK can be determined from Equation 4 and IOPEAK from Equation 5. (4) (5) To determine the maximum supply voltage the following conditions must be considered. Add the dropout voltage to the peak output swing VOPEAK, to get the supply rail at a current of IOPEAK. The regulation of the supply determines the unloaded voltage which is usually about 15% higher. The supply voltage will also rise 10% during high line conditions. Therefore the maximum supply voltage is obtained from the following equation. Max supplies (VOPEAK + VOD) (1 + regulation) (1.1) (6) For 15W of output power into an 8 load, the required VOPEAK is 15.49V. A minimum supply rail of 20.5V results from adding VOPEAK and VOD. With regulation, the maximum supplies are 26V and the required IOPEAK is 1.94A from Equation 5. It should be noted that for a dual 15W amplifier into an 8 load the IOPEAK drawn from the supplies is twice 1.94 Apk or 3.88 Apk. At this point it is a good idea to check the Power Output vs Supply Voltage to ensure that the required output power is obtainable from the device while maintaining low THD+N. In addition, the designer should verify that with the required power supply voltage and load impedance, that the required heatsink value SA is feasible given system cost and size constraints. Once the heatsink issues have been addressed, the required gain can be determined from Equation 7. (7) From Equation 7, the minimum AV is: AV 11. By selecting a gain of 21, and with a feedback resistor, Rf = 20 k, the value of Ri follows from Equation 8. Ri = Rf (AV - 1) 18 (8) Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 LM4765 www.ti.com SNAS030C - AUGUST 1998 - REVISED APRIL 2013 Thus with Ri = 1 k a non-inverting gain of 21 will result. Since the desired input impedance was 47 k, a value of 47 k was selected for RIN. The final design step is to address the bandwidth requirements which must be stated as a pair of -3 dB frequency points. Five times away from a -3 dB point is 0.17 dB down from passband response which is better than the required 0.25 dB specified. This fact results in a low and high frequency pole of 4 Hz and 100 kHz respectively. As stated in the External Components section, Ri in conjunction with Ci create a high-pass filter. Ci 1/(2 * 1 k * 4 Hz) = 39.8 F; use 39 F. (9) The high frequency pole is determined by the product of the desired high frequency pole, fH, and the gain, AV. With a AV = 21 and fH = 100 kHz, the resulting GBWP is 2.1 MHz, which is less than the ensured minimum GBWP of the LM4765 of 5 MHz. This will ensure that the high frequency response of the amplifier will be no worse than 0.17 dB down at 20 kHz which is well within the bandwidth requirements of the design. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 19 LM4765 SNAS030C - AUGUST 1998 - REVISED APRIL 2013 www.ti.com REVISION HISTORY Changes from Revision B (April 2013) to Revision C * 20 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 19 Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM4765 PACKAGE OPTION ADDENDUM www.ti.com 19-Oct-2016 PACKAGING INFORMATION Orderable Device Status (1) LM4765T/NOPB NRND Package Type Package Pins Package Drawing Qty TO-220 NDL 15 20 Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) TBD Call TI Call TI Op Temp (C) Device Marking (4/5) -20 to 85 LM4765T (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples MECHANICAL DATA NDL0015A TA15A (Rev B) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2016, Texas Instruments Incorporated