EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet The Gecko Bluetooth Low Energy family of SoCs is part of the Wireless Gecko portfolio. These Gecko SoCs are ideal for enabling energy-friendly Bluetooth 5 networking for IoT devices. KEY FEATURES * 32-bit ARM(R) Cortex(R)-M4 core with 40 MHz maximum operating frequency The single-die solution provides industry-leading energy efficiency, ultra-fast wakeup times, a scalable power amplifier, an integrated balun and no-compromise MCU features. * Up to 1 MB of flash and 256 kB of RAM * Pin-compatible across EFR32BG families (exceptions apply for 5V-tolerant pins) * 12-channel Peripheral Reflex System, Low-Energy Sensor Interface & Multichannel Capacitive Sense Interface Gecko applications include: * * * * * * * IoT Sensors and End Devices Health and Wellness Home and Building Automation Accessories Human Interface Devices Metering Commercial and Retail Lighting and Sensing * Autonomous Hardware Crypto Accelerator and True Random Number Generator * Integrated PA with up to 19 dBm (2.4 GHz) or 20 dBm (Sub-GHz) TX power * Integrated balun for 2.4 GHz * Robust peripheral set and up to 65 GPIO Core / Memory ARM CortexTM M4 processor with DSP extensions and FPU Flash Program Memory RAM Memory Clock Management Memory Protection Unit Debug Interface with ETM LDMA Controller Energy Management High Frequency Crystal Oscillator High Frequency RC Oscillator Voltage Regulator Voltage Monitor Low Frequency RC Oscillator Auxiliary High Frequency RC Oscillator DC-DC Converter Power-On Reset Low Frequency Crystal Oscillator Ultra Low Frequency RC Oscillator Brown-Out Detector Other CRYPTO CRC True Random Number Generator SMU 32-bit bus Peripheral Reflex System Radio Transceiver Sub GHz RFSENSE BALUN I LNA RF Frontend Q FRC Low Energy UARTTM To Sub GHz receive I/Q mixers and PA AGC Frequency Synthesizer MOD To 2.4 GHz receive I/Q mixers and PA I/O Ports Timers and Triggers External Interrupts Timer/Counter General Purpose I/O Low Energy Timer Watchdog Timer Pin Reset Pulse Counter Real Time Counter and Calendar Pin Wakeup Low Energy Sensor Interface Cryotimer Protocol Timer I2C Analog I/F ADC Analog Comparator IFADC Q 2.4 GHz PA PGA USART RAC PA BUFC I LNA RF Frontend Serial Interfaces DEMOD CRC RFSENSE IDAC Capacitive Sense VDAC To Sub GHz and 2.4 GHz PA Op-Amp Lowest power mode with peripheral operational: EM0--Active EM1--Sleep silabs.com | Building a more connected world. EM2--Deep Sleep EM3--Stop EM4--Hibernate EM4--Shutoff Rev. 1.6 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Feature List 1. Feature List The EFR32BG12 highlighted features are listed below. * Low Power Wireless System-on-Chip * High Performance 32-bit 40 MHz ARM Cortex(R)-M4 with DSP instruction and floating-point unit for efficient signal processing * Embedded Trace Macrocell (ETM) for advanced debugging * Up to 1024 kB flash program memory * Up to 256 kB RAM data memory * 2.4 GHz and Sub-GHz radio operation * Transmit power: * 2.4 GHz radio: Up to 19 dBm * Sub-GHz radio: Up to 20 dBm * Low Energy Consumption * 10.0 mA RX current at 1 Mbps, GFSK, 2.4 GHz * 8.4 mA RX current at 38.4 kbps, GFSK, 169 MHz * 8.5 mA TX current at 0 dBm output power at 2.4 GHz * 35.3 mA TX current at 14 dBm output power at 868 MHz * 70 A/MHz in Active Mode (EM0) * 1.5 A EM2 DeepSleep current (16 kB RAM retention and RTCC running from LFRCO) * High Receiver Performance * -94.8 dBm sensitivity at 1 Mbit/s GFSK, 2.4 GHz * -91.3 dBm sensitivity at 2 Mbit/s GFSK, 2.4 GHz * -102.7 dBm sensitivity at 250 kbps DSSS-OQPSK, 2.4 GHz * -126.2 dBm sensitivity at 600 bps, GFSK, 915 MHz * -120.6 dBm sensitivity at 2.4 kbps, GFSK, 868 MHz * -107.4 dBm sensitivity at 4.8 kbps, OOK, 433 MHz * -112.2 dBm sensitivity at 38.4 kbps, GFSK, 169 MHz * Supported Modulation Formats * 2/4 (G)FSK with fully configurable shaping * BPSK / DBPSK TX * OOK / ASK * Shaped OQPSK / (G)MSK * Configurable DSSS and FEC * Supported Protocols * Bluetooth(R) Low Energy (Bluetooth 5) * Proprietary Protocols * Wireless M-Bus * Selected IEEE 802.15.4g SUN-FSK PHYs * Low Power Wide Area Networks * Suitable for Systems Targeting Compliance With: * FCC Part 90.210 Mask D, FCC part 15.247, 15.231, 15.249 * ETSI Category I Operation, EN 300 220, EN 300 328 * ARIB T-108, T-96 * China regulatory silabs.com | Building a more connected world. * Wide selection of MCU peripherals * 12-bit 1 Msps SAR Analog to Digital Converter (ADC) * 2 x Analog Comparator (ACMP) * 2 x Digital to Analog Converter (VDAC) * 3 x Operational Amplifier (Opamp) * Digital to Analog Current Converter (IDAC) * Low-Energy Sensor Interface (LESENSE) * Multi-channel Capacitive Sense Interface (CSEN) * Up to 54 pins connected to analog channels (APORT) shared between analog peripherals * Up to 65 General Purpose I/O pins with output state retention and asynchronous interrupts * 8 Channel DMA Controller * 12 Channel Peripheral Reflex System (PRS) * 2 x 16-bit Timer/Counter * 3 or 4 Compare/Capture/PWM channels * 2 x 32-bit Timer/Counter * 3 or 4 Compare/Capture/PWM channels * 32-bit Real Time Counter and Calendar * 16-bit Low Energy Timer for waveform generation * 32-bit Ultra Low Energy Timer/Counter for periodic wake-up from any Energy Mode * 3 x 16-bit Pulse Counter with asynchronous operation * 2 x Watchdog Timer with dedicated RC oscillator * 4 x Universal Synchronous/Asynchronous Receiver/Transmitter (UART/SPI/SmartCard (ISO 7816)/IrDA/I2S) * Low Energy UART (LEUARTTM) * * * * * * 2 x I2C interface with SMBus support and address recognition in EM3 Stop Wide Operating Range * 1.8 V to 3.8 V single power supply * Integrated DC-DC, down to 1.8 V output with up to 200 mA load current for system * Standard (-40 C to 85 C) and Extended (-40 C to 125 C) temperature grades available Support for Internet Security * General Purpose CRC * True Random Number Generator * 2 x Hardware Cryptographic Acceleration for AES 128/256, SHA-1, SHA-2 (SHA-224 and SHA-256) and ECC QFN48 7x7 mm Package QFN68 8x8 mm Package BGA125 7x7 mm Package Rev. 1.6 | 2 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Ordering Information 2. Ordering Information Table 2.1. Ordering Information Ordering Code Protocol Stack EFR32BG12P433F1024GL125-C EFR32BG12P433F1024GM68-C EFR32BG12P433F1024IM68-C EFR32BG12P433F1024GM48-C EFR32BG12P432F1024GL125-C Frequency Band @ Max TX Power Flash (kB) RAM (kB) GPIO Package Temp Range Bluetooth LE 2.4 GHz @ 19 dBm 1024 256 65 BGA125 -40 to +85C Proprietary Sub-GHz @ 20 dBm Bluetooth LE 2.4 GHz @ 19 dBm 1024 256 46 QFN68 -40 to +85C Proprietary Sub-GHz @ 20 dBm Bluetooth LE 2.4 GHz @ 19 dBm 1024 256 46 QFN68 -40 to +125C Proprietary Sub-GHz @ 20 dBm Bluetooth LE 2.4 GHz @ 19 dBm 1024 256 28 QFN48 -40 to +85C Proprietary Sub-GHz @ 20 dBm Bluetooth LE 2.4 GHz @ 19 dBm 1024 256 65 BGA125 -40 to +85C 2.4 GHz @ 19 dBm 1024 256 31 QFN48 -40 to +85C 2.4 GHz @ 10 dBm 1024 256 65 BGA125 -40 to +85C 2.4 GHz @ 10 dBm 1024 256 31 QFN48 -40 to +85C 2.4 GHz @ 10 dBm 1024 256 31 QFN48 -40 to +125C 2.4 GHz @ 10 dBm 1024 128 65 BGA125 -40 to +85C 2.4 GHz @ 10 dBm 1024 128 46 QFN68 -40 to +85C 2.4 GHz @ 10 dBm 1024 128 46 QFN68 -40 to +125C 2.4 GHz @ 10 dBm 512 64 46 QFN68 -40 to +85C 2.4 GHz @ 10 dBm 512 64 46 QFN68 -40 to +125C 2.4 GHz @ 10 dBm 1024 128 31 QFN48 -40 to +85C 2.4 GHz @ 0 dBm 1024 128 65 BGA125 -40 to +85C Proprietary EFR32BG12P432F1024GM48-C Bluetooth LE Proprietary EFR32BG12P332F1024GL125-C Bluetooth LE Proprietary EFR32BG12P332F1024GM48-C Bluetooth LE Proprietary EFR32BG12P332F1024IM48-C Bluetooth LE Proprietary EFR32BG12P232F1024GL125-C Bluetooth LE Proprietary EFR32BG12P232F1024GM68-C Bluetooth LE Proprietary EFR32BG12P232F1024IM68-C Bluetooth LE Proprietary EFR32BG12P232F512GM68-C Bluetooth LE Proprietary EFR32BG12P232F512IM68-C Bluetooth LE Proprietary EFR32BG12P232F1024GM48-C Bluetooth LE Proprietary EFR32BG12P132F1024GL125-C Bluetooth LE Proprietary silabs.com | Building a more connected world. Rev. 1.6 | 3 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Ordering Information Frequency Band Ordering Code Protocol Stack @ Max TX Power Flash (kB) RAM (kB) GPIO Package Temp Range EFR32BG12P132F1024GM48-C Bluetooth LE 2.4 GHz @ 0 dBm 1024 128 31 QFN48 -40 to +85C Proprietary EFR32 X G 1 2 P 132 F 1024 G L 125 - A R Tape and Reel (Optional) Revision Pin Count Package - M (QFN), L (BGA) Temperature Grade - G (-40 to +85 C), -I (-40 to +125 C) Flash Memory Size in kB Memory Type (Flash) Feature Set Code - r2r1r0 r2: Reserved r1: RF Type - 3 (TRX), 2 (RX), 1 (TX) r0: Frequency Band - 1 (Sub-GHz), 2 (2.4 GHz), 3 (Dual-Band) Performance Grade - P (Performance), B (Basic), V (Value) Device Configuration Series Gecko Family - M, B, F Wireless Gecko 32-bit Figure 2.1. Ordering Code Key silabs.com | Building a more connected world. Rev. 1.6 | 4 Table of Contents 1. Feature List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3.2 Radio . . . . . . . . . . . . 3.2.1 Antenna Interface . . . . . . 3.2.2 Fractional-N Frequency Synthesizer 3.2.3 Receiver Architecture . . . . . 3.2.4 Transmitter Architecture . . . . 3.2.5 Wake on Radio . . . . . . . 3.2.6 RFSENSE . . . . . . . . . 3.2.7 Flexible Frame Handling . . . . 3.2.8 Packet and State Trace . . . . 3.2.9 Data Buffering . . . . . . . . 3.2.10 Radio Controller (RAC) . . . . 3.2.11 Random Number Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 . 8 . 9 . 9 . 9 . 9 .10 .10 .10 .10 .10 .11 3.3 Power . . . . . . . . . . . 3.3.1 Energy Management Unit (EMU) 3.3.2 DC-DC Converter . . . . . 3.3.3 Power Domains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 .12 .12 .12 3.4 General Purpose Input/Output (GPIO) . . . . . . . . . . . . . . . . . . . . . .13 3.5 Clocking . . . . . . . . . . 3.5.1 Clock Management Unit (CMU) . 3.5.2 Internal and External Oscillators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 .13 .13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 .13 .13 .13 .14 .14 .14 .14 3.7 Communications and Other Digital Peripherals . . . . . . . . . . 3.7.1 Universal Synchronous/Asynchronous Receiver/Transmitter (USART) . 3.7.2 Low Energy Universal Asynchronous Receiver/Transmitter (LEUART) . 3.7.3 Inter-Integrated Circuit Interface (I2C) . . . . . . . . . . . . 3.7.4 Peripheral Reflex System (PRS) . . . . . . . . . . . . . 3.7.5 Low Energy Sensor Interface (LESENSE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 .14 .14 .14 .14 .15 3.8 Security Features . . . . . . . . . . . . . . 3.8.1 General Purpose Cyclic Redundancy Check (GPCRC) 3.8.2 Crypto Accelerator (CRYPTO) . . . . . . . . 3.8.3 True Random Number Generator (TRNG) . . . . 3.8.4 Security Management Unit (SMU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 .15 .15 .15 .15 . . . 3.6 Counters/Timers and PWM . . . . . . . . . 3.6.1 Timer/Counter (TIMER) . . . . . . . . 3.6.2 Wide Timer/Counter (WTIMER) . . . . . . 3.6.3 Real Time Counter and Calendar (RTCC) . . 3.6.4 Low Energy Timer (LETIMER) . . . . . . 3.6.5 Ultra Low Power Wake-up Timer (CRYOTIMER) 3.6.6 Pulse Counter (PCNT) . . . . . . . . . 3.6.7 Watchdog Timer (WDOG) . . . . . . . . silabs.com | Building a more connected world. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rev. 1.6 | 5 3.9 Analog. . . . . . . . . . . . . . 3.9.1 Analog Port (APORT) . . . . . . . 3.9.2 Analog Comparator (ACMP) . . . . . 3.9.3 Analog to Digital Converter (ADC) . . . 3.9.4 Capacitive Sense (CSEN) . . . . . . 3.9.5 Digital to Analog Current Converter (IDAC) 3.9.6 Digital to Analog Converter (VDAC) . . 3.9.7 Operational Amplifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 .15 .15 .16 .16 .16 .16 .16 3.10 Reset Management Unit (RMU) . . . . . . . . . . . . . . . . . . . .16 3.11 Core and Memory . . . . . . . . . . . . 3.11.1 Processor Core . . . . . . . . . . . . 3.11.2 Memory System Controller (MSC) . . . . . 3.11.3 Linked Direct Memory Access Controller (LDMA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 .16 .17 .17 3.12 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 3.13 Configuration Summary . . . . . . . . . . . . . . . . . . . . . . . . . .20 4. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4.1 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . .21 4.1.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . .22 4.1.2 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . .24 4.1.3 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . .26 4.1.4 DC-DC Converter . . . . . . . . . . . . . . . . . . . . . . . . . . .27 4.1.5 Current Consumption . . . . . . . . . . . . . . . . . . . . . . . . . .29 4.1.6 Wake Up Times . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 4.1.7 Brown Out Detector (BOD) . . . . . . . . . . . . . . . . . . . . . . . .40 4.1.8 Frequency Synthesizer . . . . . . . . . . . . . . . . . . . . . . . . . .41 4.1.9 2.4 GHz RF Transceiver Characteristics . . . . . . . . . . . . . . . . . . . .42 4.1.10 Sub-GHz RF Transceiver Characteristics . . . . . . . . . . . . . . . . . . .55 4.1.11 Modem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 4.1.12 Oscillators . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 4.1.13 Flash Memory Characteristics . . . . . . . . . . . . . . . . . . . . . . .84 4.1.14 General-Purpose I/O (GPIO) . . . . . . . . . . . . . . . . . . . . . . .85 4.1.15 Voltage Monitor (VMON) . . . . . . . . . . . . . . . . . . . . . . . . .87 4.1.16 Analog to Digital Converter (ADC) . . . . . . . . . . . . . . . . . . . . .88 4.1.17 Analog Comparator (ACMP) . . . . . . . . . . . . . . . . . . . . . . .90 4.1.18 Digital to Analog Converter (VDAC) . . . . . . . . . . . . . . . . . . . . .93 4.1.19 Current Digital to Analog Converter (IDAC) . . . . . . . . . . . . . . . . . .96 4.1.20 Capacitive Sense (CSEN) . . . . . . . . . . . . . . . . . . . . . . . .98 4.1.21 Operational Amplifier (OPAMP) . . . . . . . . . . . . . . . . . . . . 1 . 00 4.1.22 Pulse Counter (PCNT) . . . . . . . . . . . . . . . . . . . . . . . 1. 03 4.1.23 Analog Port (APORT) . . . . . . . . . . . . . . . . . . . . . . . . . 103 4.1.24 I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 4.1.25 USART SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 4.2 Typical Performance Curves . . . . . . . . . . . . . . . . . . . . . . . .108 4.2.1 Supply Current . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 09 4.2.2 DC-DC Converter . . . . . . . . . . . . . . . . . . . . . . . . . 114 . 4.2.3 2.4 GHz Radio . . . . . . . . . . . . . . . . . . . . . . . . . . 116 . silabs.com | Building a more connected world. Rev. 1.6 | 6 5. Typical Connection Diagrams 5.1 Power . . . . . . . 5.2 RF Matching Networks 5.3 Other Connections. . . . . . . . . . . . . . . . . . . . . . . . . .118 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 . . . . .120 . . 121 6. Pin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 6.1 BGA125 2.4 GHz and Sub-GHz Device Pinout 6.2 BGA125 2.4 GHz Device Pinout . . . . . . . . . . . . . . . . . . . . . . .122 . . . . . . . . . . . . . . . . . . 126 6.3 QFN68 2.4 GHz and Sub-GHz Device Pinout. . . . . . . . . . . . . . . . . . . 129 6.4 QFN68 2.4 GHz Device Pinout . . . . . . . . . . . . . . . . . . . 132 . 6.5 QFN48 2.4 GHz and Sub-GHz Device Pinout. . . . . . . . . . . . . . . . . . . 134 6.6 QFN48 2.4 GHz Device Pinout 6.7 GPIO Functionality Table . . . . . . . . . . . . . . . . . . . . . . . . . . 136 . . . . . . . . . . . . . . . . . . . . . . . 1 . 38 6.8 Alternate Functionality Overview . . 6.9 Analog Port (APORT) Client Maps 7. BGA125 Package Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 . .196 . . . . . . . . . . . . . . . . . . . . . . .205 7.1 BGA125 Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 205 7.2 BGA125 PCB Land Pattern . . . . . . . . . . . . . . . . . . . . . . . . 207 . 7.3 BGA125 Package Marking . . . . . . . . . . . . . . . . . . . . . . . . . 209 8. QFN48 Package Specifications. . . . . . . . . . . . . . . . . . . . . . . . 210 8.1 QFN48 Package Dimensions 8.2 QFN48 PCB Land Pattern . 8.3 QFN48 Package Marking . . . . . . . . . . . . . . . . . . . . . . . . 210 . . . . . . . . . . . . . . . . . . . . . . . .212 . . . . . . . . . . . . . . . . . . . . . . . . .214 9. QFN68 Package Specifications. . . . . . . . . . . . . . . . . . . . . . . . 215 9.1 QFN68 Package Dimensions 9.2 QFN68 PCB Land Pattern 9.3 QFN68 Package Marking . . . . . . . . . . . . . . . . . . . . . . . . . . 215 . . . . . . . . . . . . . . . . . . . . . . . .217 . . . . . . . . . . . . . . . . . . . . . . . .219 10. Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 silabs.com | Building a more connected world. Rev. 1.6 | 7 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet System Overview 3. System Overview 3.1 Introduction The EFR32 product family combines an energy-friendly MCU with a highly integrated radio transceiver. The devices are well suited for any battery operated application as well as other systems requiring high performance and low energy consumption. This section gives a short introduction to the full radio and MCU system. The detailed functional description can be found in the EFR32xG12 Wireless Gecko Reference Manual. A block diagram of the EFR32BG12 family is shown in Figure 3.1 Detailed EFR32BG12 Block Diagram on page 8. The diagram shows a superset of features available on the family, which vary by OPN. For more information about specific device features, consult Ordering Information. Radio Transceiver To RF Frontend Circuits Q AGC MOD FRC BUFC PCNT Port Mapper Brown Out / Power-On Reset ARM Cortex-M4 Core Up to 256 KB RAM Memory Protection Unit PAVDD Energy Management Floating Point Unit LDMA Controller RFVDD IOVDD Voltage Monitor AVDD DVDD Watchdog Timer bypass VREGVDD VREGSW DC-DC Converter Voltage Regulator DECOUPLE LFXTAL_P LFXTAL_N HFXTAL_P HFXTAL_N I2C Up to 1024 KB ISP Flash Program Memory Clock Management ULFRCO AUXHFRCO CRYPTO A A H P B B Port B Drivers PBn Port C Drivers PCn Port D Drivers PDn Port F Drivers PFn Port I Drivers PIn Port J Drivers PJn Port K Drivers PKn CRC LESENSE Analog Peripherals IDAC VDAC Internal Reference 12-bit ADC LFRCO LFXO HFRCO HFXO Mux & FB Debug Signals (shared w/GPIO) Serial Wire and ETM Debug / Programming LEUART Input Mux RESETn PAn RTC / RTCC USART Reset Management Unit Port A Drivers CRYOTIMER RAC Frequency Synthesizer Op-Amp VDD APORT PA Digital Peripherals LETIMER TIMER I LNA BALUN IFADC PGA Q 2.4 GHz RF CRC PA RFSENSE 2G4RF_ION DEMOD LNA IOVDD + - SUBGRF_IP SUBGRF_IN SUBGRF_OP SUBGRF_ON 2G4RF_IOP Port I/O Configuration Sub-GHz RF I Temp Sense Capacitive Sense + Analog Comparator Figure 3.1. Detailed EFR32BG12 Block Diagram 3.2 Radio The Gecko family features a radio transceiver supporting Bluetooth(R) Low Energy and proprietary short range wireless protocols. 3.2.1 Antenna Interface The 2.4 GHz antenna interface consists of two pins (2G4RF_IOP and 2G4RF_ION) that interface directly to the on-chip BALUN. The 2G4RF_ION pin should be grounded externally. The external components and power supply connections for the antenna interface typical applications are shown in the RF Matching Networks section. silabs.com | Building a more connected world. Rev. 1.6 | 8 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet System Overview 3.2.2 Fractional-N Frequency Synthesizer The EFR32BG12 contains a high performance, low phase noise, fully integrated fractional-N frequency synthesizer. The synthesizer is used in receive mode to generate the LO frequency used by the down-conversion mixer. It is also used in transmit mode to directly generate the modulated RF carrier. The fractional-N architecture provides excellent phase noise performance combined with frequency resolution better than 100 Hz, with low energy consumption. The synthesizer has fast frequency settling which allows very short receiver and transmitter wake up times to optimize system energy consumption. 3.2.3 Receiver Architecture The EFR32BG12 uses a low-IF receiver architecture, consisting of a Low-Noise Amplifier (LNA) followed by an I/Q down-conversion mixer, employing a crystal reference. The I/Q signals are further filtered and amplified before being sampled by the IF analog-to-digital converter (IFADC). The IF frequency is configurable from 150 kHz to 1371 kHz. The IF can further be configured for high-side or low-side injection, providing flexibility with respect to known interferers at the image frequency. The Automatic Gain Control (AGC) block adjusts the receiver gain to optimize performance and avoid saturation for excellent selectivity and blocking performance. The 2.4 GHz radio is calibrated at production to improve image rejection performance. The sub-GHz radio can be calibrated on-demand by the user for the desired frequency band. Demodulation is performed in the digital domain. The demodulator performs configurable decimation and channel filtering to allow receive bandwidths ranging from 0.1 to 2530 kHz. High carrier frequency and baud rate offsets are tolerated by active estimation and compensation. Advanced features supporting high quality communication under adverse conditions include forward error correction by block and convolutional coding as well as Direct Sequence Spread Spectrum (DSSS) for 2.4 GHz and sub-GHz bands. A Received Signal Strength Indicator (RSSI) is available for signal quality metrics, for level-based proximity detection, and for RF channel access by Collision Avoidance (CA) or Listen Before Talk (LBT) algorithms. An RSSI capture value is associated with each received frame and the dynamic RSSI measurement can be monitored throughout reception. The EFR32BG12 features integrated support for antenna diversity to mitigate the problem of frequency-selective fading due to multipath propagation and improve link budget. Support for antenna diversity is available for specific PHY configurations in 2.4 GHz and sub-GHz bands. Internal configurable hardware controls an external switch for automatic switching between antennae during RF receive detection operations. Note: Due to the shorter preamble of 802.15.4 and BLE packets, RX diversity is not supported. 3.2.4 Transmitter Architecture The EFR32BG12 uses a direct-conversion transmitter architecture. For constant envelope modulation formats, the modulator controls phase and frequency modulation in the frequency synthesizer. Transmit symbols or chips are optionally shaped by a digital shaping filter. The shaping filter is fully configurable, including the BT product, and can be used to implement Gaussian or Raised Cosine shaping. Carrier Sense Multiple Access - Collision Avoidance (CSMA-CA) or Listen Before Talk (LBT) algorithms can be automatically timed by the EFR32BG12. These algorithms are typically defined by regulatory standards to improve inter-operability in a given bandwidth between devices that otherwise lack synchronized RF channel access. 3.2.5 Wake on Radio The Wake on Radio feature allows flexible, autonomous RF sensing, qualification, and demodulation without required MCU activity, using a subsystem of the EFR32BG12 including the Radio Controller (RAC), Peripheral Reflex System (PRS), and Low Energy peripherals. silabs.com | Building a more connected world. Rev. 1.6 | 9 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet System Overview 3.2.6 RFSENSE The RFSENSE peripheral generates a system wakeup interrupt upon detection of wideband RF energy at the antenna interface, providing true RF wakeup capabilities from low energy modes including EM2, EM3 and EM4. RFSENSE triggers on a relatively strong RF signal and is available in the lowest energy modes, allowing exceptionally low energy consumption. RFSENSE does not demodulate or otherwise qualify the received signal, but software may respond to the wakeup event by enabling normal RF reception. Various strategies for optimizing power consumption and system response time in presence of false alarms may be employed using available timer peripherals. 3.2.7 Flexible Frame Handling EFR32BG12 has an extensive and flexible frame handling support for easy implementation of even complex communication protocols. The Frame Controller (FRC) supports all low level and timing critical tasks together with the Radio Controller and Modulator/Demodulator: * Highly adjustable preamble length * Up to 2 simultaneous synchronization words, each up to 32 bits and providing separate interrupts * Frame disassembly and address matching (filtering) to accept or reject frames * Automatic ACK frame assembly and transmission * Fully flexible CRC generation and verification: * Multiple CRC values can be embedded in a single frame * 8, 16, 24 or 32-bit CRC value * Configurable CRC bit and byte ordering * Selectable bit-ordering (least significant or most significant bit first) * Optional data whitening * Optional Forward Error Correction (FEC), including convolutional encoding / decoding and block encoding / decoding * Half rate convolutional encoder and decoder with constraint lengths from 2 to 7 and optional puncturing * Optional symbol interleaving, typically used in combination with FEC * Symbol coding, such as Manchester or DSSS, or biphase space encoding using FEC hardware * UART encoding over air, with start and stop bit insertion / removal * Test mode support, such as modulated or unmodulated carrier output * Received frame timestamping 3.2.8 Packet and State Trace The EFR32BG12 Frame Controller has a packet and state trace unit that provides valuable information during the development phase. It features: * Non-intrusive trace of transmit data, receive data and state information * Data observability on a single-pin UART data output, or on a two-pin SPI data output * Configurable data output bitrate / baudrate * Multiplexed transmitted data, received data and state / meta information in a single serial data stream 3.2.9 Data Buffering The EFR32BG12 features an advanced Radio Buffer Controller (BUFC) capable of handling up to 4 buffers of adjustable size from 64 bytes to 4096 bytes. Each buffer can be used for RX, TX or both. The buffer data is located in RAM, enabling zero-copy operations. 3.2.10 Radio Controller (RAC) The Radio Controller controls the top level state of the radio subsystem in the EFR32BG12. It performs the following tasks: * Precisely-timed control of enabling and disabling of the receiver and transmitter circuitry * Run-time calibration of receiver, transmitter and frequency synthesizer * Detailed frame transmission timing, including optional LBT or CSMA-CA silabs.com | Building a more connected world. Rev. 1.6 | 10 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet System Overview 3.2.11 Random Number Generator The Frame Controller (FRC) implements a random number generator that uses entropy gathered from noise in the RF receive chain. The data is suitable for use in cryptographic applications. Output from the random number generator can be used either directly or as a seed or entropy source for software-based random number generator algorithms such as Fortuna. silabs.com | Building a more connected world. Rev. 1.6 | 11 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet System Overview 3.3 Power The EFR32BG12 has an Energy Management Unit (EMU) and efficient integrated regulators to generate internal supply voltages. Only a single external supply voltage is required, from which all internal voltages are created. An optional integrated DC-DC buck regulator can be utilized to further reduce the current consumption. The DC-DC regulator requires one external inductor and one external capacitor. The EFR32BG12 device family includes support for internal supply voltage scaling, as well as two different power domains groups for peripherals. These enhancements allow for further supply current reductions and lower overall power consumption. AVDD and VREGVDD need to be 1.8 V or higher for the MCU to operate across all conditions; however the rest of the system will operate down to 1.62 V, including the digital supply and I/O. This means that the device is fully compatible with 1.8 V components. Running from a sufficiently high supply, the device can use the DC-DC to regulate voltage not only for itself, but also for other PCB components, supplying up to a total of 200 mA. 3.3.1 Energy Management Unit (EMU) The Energy Management Unit manages transitions of energy modes in the device. Each energy mode defines which peripherals and features are available and the amount of current the device consumes. The EMU can also be used to turn off the power to unused RAM blocks, and it contains control registers for the DC-DC regulator and the Voltage Monitor (VMON). The VMON is used to monitor multiple supply voltages. It has multiple channels which can be programmed individually by the user to determine if a sensed supply has fallen below a chosen threshold. 3.3.2 DC-DC Converter The DC-DC buck converter covers a wide range of load currents and provides up to 90% efficiency in energy modes EM0, EM1, EM2 and EM3, and can supply up to 200 mA to the device and surrounding PCB components. Patented RF noise mitigation allows operation of the DC-DC converter without degrading sensitivity of radio components. Protection features include programmable current limiting, short-circuit protection, and dead-time protection. The DC-DC converter may also enter bypass mode when the input voltage is too low for efficient operation. In bypass mode, the DC-DC input supply is internally connected directly to its output through a low resistance switch. Bypass mode also supports in-rush current limiting to prevent input supply voltage droops due to excessive output current transients. 3.3.3 Power Domains The EFR32BG12 has two peripheral power domains for operation in EM2 and lower. If all of the peripherals in a peripheral power domain are configured as unused, the power domain for that group will be powered off in the low-power mode, reducing the overall current consumption of the device. Table 3.1. Peripheral Power Subdomains Peripheral Power Domain 1 Peripheral Power Domain 2 ACMP0 ACMP1 PCNT0 PCNT1 ADC0 PCNT2 LETIMER0 CSEN LESENSE DAC0 APORT LEUART0 - I2C0 - I2C1 - IDAC silabs.com | Building a more connected world. Rev. 1.6 | 12 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet System Overview 3.4 General Purpose Input/Output (GPIO) EFR32BG12 has up to 65 General Purpose Input/Output pins. Each GPIO pin can be individually configured as either an output or input. More advanced configurations including open-drain, open-source, and glitch-filtering can be configured for each individual GPIO pin. The GPIO pins can be overridden by peripheral connections, like SPI communication. Each peripheral connection can be routed to several GPIO pins on the device. The input value of a GPIO pin can be routed through the Peripheral Reflex System to other peripherals. The GPIO subsystem supports asynchronous external pin interrupts. 3.5 Clocking 3.5.1 Clock Management Unit (CMU) The Clock Management Unit controls oscillators and clocks in the EFR32BG12. Individual enabling and disabling of clocks to all peripherals is performed by the CMU. The CMU also controls enabling and configuration of the oscillators. A high degree of flexibility allows software to optimize energy consumption in any specific application by minimizing power dissipation in unused peripherals and oscillators. 3.5.2 Internal and External Oscillators The EFR32BG12 supports two crystal oscillators and fully integrates four RC oscillators, listed below. * A high frequency crystal oscillator (HFXO) with integrated load capacitors, tunable in small steps, provides a precise timing reference for the MCU. Crystal frequencies in the range from 38 to 40 MHz are supported. An external clock source such as a TCXO can also be applied to the HFXO input for improved accuracy over temperature. * A 32.768 kHz crystal oscillator (LFXO) provides an accurate timing reference for low energy modes. * An integrated high frequency RC oscillator (HFRCO) is available for the MCU system, when crystal accuracy is not required. The HFRCO employs fast startup at minimal energy consumption combined with a wide frequency range. * An integrated auxilliary high frequency RC oscillator (AUXHFRCO) is available for timing the general-purpose ADC and the Serial Wire Viewer port with a wide frequency range. * An integrated low frequency 32.768 kHz RC oscillator (LFRCO) can be used as a timing reference in low energy modes, when crystal accuracy is not required. * An integrated ultra-low frequency 1 kHz RC oscillator (ULFRCO) is available to provide a timing reference at the lowest energy consumption in low energy modes. 3.6 Counters/Timers and PWM 3.6.1 Timer/Counter (TIMER) TIMER peripherals keep track of timing, count events, generate PWM outputs and trigger timed actions in other peripherals through the PRS system. The core of each TIMER is a 16-bit counter with up to 4 compare/capture channels. Each channel is configurable in one of three modes. In capture mode, the counter state is stored in a buffer at a selected input event. In compare mode, the channel output reflects the comparison of the counter to a programmed threshold value. In PWM mode, the TIMER supports generation of pulse-width modulation (PWM) outputs of arbitrary waveforms defined by the sequence of values written to the compare registers, with optional dead-time insertion available in timer unit TIMER_0 only. 3.6.2 Wide Timer/Counter (WTIMER) WTIMER peripherals function just as TIMER peripherals, but are 32 bits wide. They keep track of timing, count events, generate PWM outputs and trigger timed actions in other peripherals through the PRS system. The core of each WTIMER is a 32-bit counter with up to 4 compare/capture channels. Each channel is configurable in one of three modes. In capture mode, the counter state is stored in a buffer at a selected input event. In compare mode, the channel output reflects the comparison of the counter to a programmed threshold value. In PWM mode, the WTIMER supports generation of pulse-width modulation (PWM) outputs of arbitrary waveforms defined by the sequence of values written to the compare registers, with optional dead-time insertion available in timer unit WTIMER_0 only. 3.6.3 Real Time Counter and Calendar (RTCC) The Real Time Counter and Calendar (RTCC) is a 32-bit counter providing timekeeping in all energy modes. The RTCC includes a Binary Coded Decimal (BCD) calendar mode for easy time and date keeping. The RTCC can be clocked by any of the on-board oscillators with the exception of the AUXHFRCO, and it is capable of providing system wake-up at user defined instances. When receiving frames, the RTCC value can be used for timestamping. The RTCC includes 128 bytes of general purpose data retention, allowing easy and convenient data storage in all energy modes down to EM4H. silabs.com | Building a more connected world. Rev. 1.6 | 13 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet System Overview 3.6.4 Low Energy Timer (LETIMER) The unique LETIMER is a 16-bit timer that is available in energy mode EM0 Active, EM1 Sleep, EM2 Deep Sleep, and EM3 Stop. This allows it to be used for timing and output generation when most of the device is powered down, allowing simple tasks to be performed while the power consumption of the system is kept at an absolute minimum. The LETIMER can be used to output a variety of waveforms with minimal software intervention. The LETIMER is connected to the Real Time Counter and Calendar (RTCC), and can be configured to start counting on compare matches from the RTCC. 3.6.5 Ultra Low Power Wake-up Timer (CRYOTIMER) The CRYOTIMER is a 32-bit counter that is capable of running in all energy modes. It can be clocked by either the 32.768 kHz crystal oscillator (LFXO), the 32.768 kHz RC oscillator (LFRCO), or the 1 kHz RC oscillator (ULFRCO). It can provide periodic Wakeup events and PRS signals which can be used to wake up peripherals from any energy mode. The CRYOTIMER provides a wide range of interrupt periods, facilitating flexible ultra-low energy operation. 3.6.6 Pulse Counter (PCNT) The Pulse Counter (PCNT) peripheral can be used for counting pulses on a single input or to decode quadrature encoded inputs. The clock for PCNT is selectable from either an external source on pin PCTNn_S0IN or from an internal timing reference, selectable from among any of the internal oscillators, except the AUXHFRCO. The peripheral may operate in energy mode EM0 Active, EM1 Sleep, EM2 Deep Sleep, and EM3 Stop. 3.6.7 Watchdog Timer (WDOG) The watchdog timer can act both as an independent watchdog or as a watchdog synchronous with the CPU clock. It has windowed monitoring capabilities, and can generate a reset or different interrupts depending on the failure mode of the system. The watchdog can also monitor autonomous systems driven by PRS. 3.7 Communications and Other Digital Peripherals 3.7.1 Universal Synchronous/Asynchronous Receiver/Transmitter (USART) The Universal Synchronous/Asynchronous Receiver/Transmitter is a flexible serial I/O interface. It supports full duplex asynchronous UART communication with hardware flow control as well as RS-485, SPI, MicroWire and 3-wire. It can also interface with devices supporting: * ISO7816 SmartCards * IrDA * I2S 3.7.2 Low Energy Universal Asynchronous Receiver/Transmitter (LEUART) The unique LEUARTTM provides two-way UART communication on a strict power budget. Only a 32.768 kHz clock is needed to allow UART communication up to 9600 baud. The LEUART includes all necessary hardware to make asynchronous serial communication possible with a minimum of software intervention and energy consumption. 3.7.3 Inter-Integrated Circuit Interface (I2C) The I2C interface enables communication between the MCU and a serial I2C bus. It is capable of acting as both a master and a slave and supports multi-master buses. Standard-mode, fast-mode and fast-mode plus speeds are supported, allowing transmission rates from 10 kbit/s up to 1 Mbit/s. Slave arbitration and timeouts are also available, allowing implementation of an SMBus-compliant system. The interface provided to software by the I2C peripheral allows precise timing control of the transmission process and highly automated transfers. Automatic recognition of slave addresses is provided in active and low energy modes. 3.7.4 Peripheral Reflex System (PRS) The Peripheral Reflex System provides a communication network between different peripherals without software involvement. Peripherals producing Reflex signals are called producers. The PRS routes Reflex signals from producers to consumer peripherals, which in turn perform actions in response. Edge triggers and other functionality such as simple logic operations (AND, OR, NOT) can be applied by the PRS to the signals. The PRS allows peripheral to act autonomously without waking the MCU core, saving power. silabs.com | Building a more connected world. Rev. 1.6 | 14 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet System Overview 3.7.5 Low Energy Sensor Interface (LESENSE) The Low Energy Sensor Interface LESENSETM is a highly configurable sensor interface with support for up to 16 individually configurable sensors. By controlling the analog comparators, ADC, and DAC, LESENSE is capable of supporting a wide range of sensors and measurement schemes, and can for instance measure LC sensors, resistive sensors and capacitive sensors. LESENSE also includes a programmable finite state machine which enables simple processing of measurement results without CPU intervention. LESENSE is available in energy mode EM2, in addition to EM0 and EM1, making it ideal for sensor monitoring in applications with a strict energy budget. 3.8 Security Features 3.8.1 General Purpose Cyclic Redundancy Check (GPCRC) The GPCRC block implements a Cyclic Redundancy Check (CRC) function. It supports both 32-bit and 16-bit polynomials. The supported 32-bit polynomial is 0x04C11DB7 (IEEE 802.3), while the 16-bit polynomial can be programmed to any value, depending on the needs of the application. 3.8.2 Crypto Accelerator (CRYPTO) The Crypto Accelerator is a fast and energy-efficient autonomous hardware encryption and decryption accelerator. EFR32 devices support AES encryption and decryption with 128- or 256-bit keys, ECC over both GF(P) and GF(2m), SHA-1 and SHA-2 (SHA-224 and SHA-256). Supported block cipher modes of operation for AES include: ECB, CTR, CBC, PCBC, CFB, OFB, GCM, CBC-MAC, GMAC and CCM. Supported ECC NIST recommended curves include P-192, P-224, P-256, K-163, K-233, B-163 and B-233. The CRYPTO1 block is tightly linked to the Radio Buffer Controller (BUFC) enabling fast and efficient autonomous cipher operations on data buffer content. It allows fast processing of GCM (AES), ECC and SHA with little CPU intervention. CRYPTO also provides trigger signals for DMA read and write operations. 3.8.3 True Random Number Generator (TRNG) The TRNG is a non-deterministic random number generator based on a full hardware solution. The TRNG is validated with NIST800-22 and AIS-31 test suites as well as being suitable for FIPS 140-2 certification (for the purposes of cryptographic key generation). Note: TRNG operation is only supported at VSCALE2. TRNG cannot be used at VSCALE0. 3.8.4 Security Management Unit (SMU) The Security Management Unit (SMU) allows software to set up fine-grained security for peripheral access, which is not possible in the Memory Protection Unit (MPU). Peripherals may be secured by hardware on an individual basis, such that only priveleged accesses to the peripheral's register interface will be allowed. When an access fault occurs, the SMU reports the specific peripheral involved and can optionally generate an interrupt. 3.9 Analog 3.9.1 Analog Port (APORT) The Analog Port (APORT) is an analog interconnect matrix allowing access to many analog peripherals on a flexible selection of pins. Each APORT bus consists of analog switches connected to a common wire. Since many clients can operate differentially, buses are grouped by X/Y pairs. 3.9.2 Analog Comparator (ACMP) The Analog Comparator is used to compare the voltage of two analog inputs, with a digital output indicating which input voltage is higher. Inputs are selected from among internal references and external pins. The tradeoff between response time and current consumption is configurable by software. Two 6-bit reference dividers allow for a wide range of internally-programmable reference sources. The ACMP can also be used to monitor the supply voltage. An interrupt can be generated when the supply falls below or rises above the programmable threshold. silabs.com | Building a more connected world. Rev. 1.6 | 15 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet System Overview 3.9.3 Analog to Digital Converter (ADC) The ADC is a Successive Approximation Register (SAR) architecture, with a resolution of up to 12 bits at up to 1 Msps. The output sample resolution is configurable and additional resolution is possible using integrated hardware for averaging over multiple samples. The ADC includes integrated voltage references and an integrated temperature sensor. Inputs are selectable from a wide range of sources, including pins configurable as either single-ended or differential. 3.9.4 Capacitive Sense (CSEN) The CSEN peripheral is a dedicated Capacitive Sensing block for implementing touch-sensitive user interface elements such a switches and sliders. The CSEN peripheral uses a charge ramping measurement technique, which provides robust sensing even in adverse conditions including radiated noise and moisture. The peripheral can be configured to take measurements on a single port pin or scan through multiple pins and store results to memory through DMA. Several channels can also be shorted together to measure the combined capacitance or implement wake-on-touch from very low energy modes. Hardware includes a digital accumulator and an averaging filter, as well as digital threshold comparators to reduce software overhead. 3.9.5 Digital to Analog Current Converter (IDAC) The IDAC can source or sink a configurable constant current. This current can be driven on an output pin or routed to the selected ADC input pin for capacitive sensing. The full-scale current is programmable between 0.05 A and 64 A with several ranges consisting of various step sizes. 3.9.6 Digital to Analog Converter (VDAC) The Digital to Analog Converter (VDAC) can convert a digital value to an analog output voltage. The VDAC is a fully differential, 500 ksps, 12-bit converter. The opamps are used in conjunction with the VDAC, to provide output buffering. One opamp is used per singleended channel, or two opamps are used to provide differential outputs. The VDAC may be used for a number of different applications such as sensor interfaces or sound output. The VDAC can generate high-resolution analog signals while the MCU is operating at low frequencies and with low total power consumption. Using DMA and a timer, the VDAC can be used to generate waveforms without any CPU intervention. The VDAC is available in all energy modes down to and including EM3. 3.9.7 Operational Amplifiers The opamps are low power amplifiers with a high degree of flexibility targeting a wide variety of standard opamp application areas, and are available down to EM3. With flexible built-in programming for gain and interconnection they can be configured to support multiple common opamp functions. All pins are also available externally for filter configurations. Each opamp has a rail to rail input and a rail to rail output. They can be used in conjunction with the VDAC peripheral or in stand-alone configurations. The opamps save energy, PCB space, and cost as compared with standalone opamps because they are integrated on-chip. 3.10 Reset Management Unit (RMU) The RMU is responsible for handling reset of the EFR32BG12. A wide range of reset sources are available, including several power supply monitors, pin reset, software controlled reset, core lockup reset, and watchdog reset. 3.11 Core and Memory 3.11.1 Processor Core The ARM Cortex-M processor includes a 32-bit RISC processor integrating the following features and tasks in the system: * ARM Cortex-M4 RISC processor achieving 1.25 Dhrystone MIPS/MHz * Memory Protection Unit (MPU) supporting up to 8 memory segments * Up to 1024 kB flash program memory * Up to 256 kB RAM data memory * Configuration and event handling of all peripherals * 2-pin Serial-Wire debug interface silabs.com | Building a more connected world. Rev. 1.6 | 16 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet System Overview 3.11.2 Memory System Controller (MSC) The Memory System Controller (MSC) is the program memory unit of the microcontroller. The flash memory is readable and writable from both the Cortex-M and DMA. The flash memory is divided into two blocks; the main block and the information block. Program code is normally written to the main block, whereas the information block is available for special user data and flash lock bits. There is also a read-only page in the information block containing system and device calibration data. Read and write operations are supported in energy modes EM0 Active and EM1 Sleep. 3.11.3 Linked Direct Memory Access Controller (LDMA) The Linked Direct Memory Access (LDMA) controller allows the system to perform memory operations independently of software. This reduces both energy consumption and software workload. The LDMA allows operations to be linked together and staged, enabling sophisticated operations to be implemented. silabs.com | Building a more connected world. Rev. 1.6 | 17 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet System Overview 3.12 Memory Map The EFR32BG12 memory map is shown in the figures below. RAM and flash sizes are for the largest memory configuration. Figure 3.2. EFR32BG12 Memory Map -- Core Peripherals and Code Space silabs.com | Building a more connected world. Rev. 1.6 | 18 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet System Overview Figure 3.3. EFR32BG12 Memory Map -- Peripherals silabs.com | Building a more connected world. Rev. 1.6 | 19 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet System Overview 3.13 Configuration Summary The features of the EFR32BG12 are a subset of the feature set described in the device reference manual. The table below describes device specific implementation of the features. Remaining modules support full configuration. Table 3.2. Configuration Summary Module Configuration Pin Connections USART0 IrDA US0_TX, US0_RX, US0_CLK, US0_CS SmartCard USART1 I2S US1_TX, US1_RX, US1_CLK, US1_CS SmartCard USART2 IrDA US2_TX, US2_RX, US2_CLK, US2_CS SmartCard USART3 I2S US3_TX, US3_RX, US3_CLK, US3_CS SmartCard TIMER0 with DTI TIM0_CC[2:0], TIM0_CDTI[2:0] TIMER1 - TIM1_CC[3:0] WTIMER0 with DTI WTIM0_CC[2:0], WTIM0_CDTI[2:0] WTIMER1 - WTIM1_CC[3:0] silabs.com | Building a more connected world. Rev. 1.6 | 20 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4. Electrical Specifications 4.1 Electrical Characteristics All electrical parameters in all tables are specified under the following conditions, unless stated otherwise: * Typical values are based on TAMB=25 C and VDD= 3.3 V, by production test and/or technology characterization. * Radio performance numbers are measured in conducted mode, based on Silicon Laboratories reference designs using output power-specific external RF impedance-matching networks for interfacing to a 50 antenna. * Minimum and maximum values represent the worst conditions across supply voltage, process variation, and operating temperature, unless stated otherwise. Refer to 4.1.2.1 General Operating Conditions for more details about operational supply and temperature limits. silabs.com | Building a more connected world. Rev. 1.6 | 21 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.1 Absolute Maximum Ratings Stresses above those listed below may cause permanent damage to the device. This is a stress rating only and functional operation of the devices at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. For more information on the available quality and reliability data, see the Quality and Reliability Monitor Report at http://www.silabs.com/support/quality/pages/default.aspx. Table 4.1. Absolute Maximum Ratings Parameter Symbol Storage temperature range Test Condition Min Typ Max Unit TSTG -50 -- 150 C Voltage on any supply pin VDDMAX -0.3 -- 3.8 V Voltage ramp rate on any supply pin VDDRAMPMAX -- -- 1 V / s DC voltage on any GPIO pin VDIGPIN 5V tolerant GPIO pins1 2 3 -0.3 -- Min of 5.25 and IOVDD +2 V Standard GPIO pins -0.3 -- IOVDD+0.3 V -0.3 -- 1.4 V Voltage on HFXO pins VHFXOPIN Input RF level on pins 2G4RF_IOP and 2G4RF_ION PRFMAX2G4 -- -- 10 dBm Voltage differential between RF pins (2G4RF_IOP 2G4RF_ION) VMAXDIFF2G4 -50 -- 50 mV Absolute voltage on RF pins 2G4RF_IOP and 2G4RF_ION VMAX2G4 -0.3 -- 3.8 V Absolute voltage on SubGHz RF pins VMAXSUBG Pins SUBGRF_OP and SUBGRF_ON -0.3 -- 3.8 V Pins SUBGRF_IP and SUBGRF_IN, -0.3 -- 0.3 V Total current into VDD power IVDDMAX lines Source -- -- 200 mA Total current into VSS ground lines IVSSMAX Sink -- -- 200 mA Current per I/O pin IIOMAX Sink -- -- 50 mA Source -- -- 50 mA Sink -- -- 200 mA Source -- -- 200 mA -G grade devices -40 -- 105 C -I grade devices -40 -- 125 C Current for all I/O pins Junction temperature IIOALLMAX TJ silabs.com | Building a more connected world. Rev. 1.6 | 22 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Note: 1. When a GPIO pin is routed to the analog block through the APORT, the maximum voltage = IOVDD. 2. Valid for IOVDD in valid operating range or when IOVDD is undriven (high-Z). If IOVDD is connected to a low-impedance source below the valid operating range (e.g. IOVDD shorted to VSS), the pin voltage maximum is IOVDD + 0.3 V, to avoid exceeding the maximum IO current specifications. 3. To operate above the IOVDD supply rail, over-voltage tolerance must be enabled according to the GPIO_Px_OVTDIS register. Pins with over-voltage tolerance disabled have the same limits as Standard GPIO. silabs.com | Building a more connected world. Rev. 1.6 | 23 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.2 Operating Conditions When assigning supply sources, the following requirements must be observed: * VREGVDD must be greater than or equal to AVDD, DVDD, RFVDD, PAVDD and all IOVDD supplies. * VREGVDD = AVDD * DVDD AVDD * IOVDD AVDD * RFVDD AVDD * PAVDD AVDD silabs.com | Building a more connected world. Rev. 1.6 | 24 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.2.1 General Operating Conditions Table 4.2. General Operating Conditions Parameter Symbol Test Condition Min Typ Max Unit Operating ambient temperature range1 TA -G temperature grade -40 25 85 C -I temperature grade -40 25 125 C AVDD supply voltage2 VAVDD 1.8 3.3 3.8 V VREGVDD operating supply voltage2 3 VVREGVDD DCDC in regulation 2.4 3.3 3.8 V DCDC in bypass, 50mA load 1.8 3.3 3.8 V DCDC not in use. DVDD externally shorted to VREGVDD 1.8 3.3 3.8 V DCDC in bypass, T 85 C -- -- 200 mA DCDC in bypass, T > 85 C -- -- 100 mA VREGVDD current IVREGVDD RFVDD operating supply voltage VRFVDD 1.62 -- VVREGVDD V DVDD operating supply voltage VDVDD 1.62 -- VVREGVDD V PAVDD operating supply voltage VPAVDD 1.62 -- VVREGVDD V 1.62 -- VVREGVDD V 0.75 1.0 2.75 F -- -- 0.1 V VSCALE2, MODE = WS1 -- -- 40 MHz VSCALE2, MODE = WS0 -- -- 25 MHz VSCALE0, MODE = WS2 -- -- 20 MHz VSCALE0, MODE = WS1 -- -- 14 MHz VSCALE0, MODE = WS0 -- -- 7 MHz VSCALE2 -- -- 40 MHz VSCALE0 -- -- 20 MHz IOVDD operating supply volt- VIOVDD age DECOUPLE output capacitor5 6 All IOVDD pins4 CDECOUPLE Difference between AVDD dVDD and VREGVDD, ABS(AVDDVREGVDD)2 HFCORECLK frequency HFCLK frequency fCORE fHFCLK silabs.com | Building a more connected world. Rev. 1.6 | 25 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Note: 1. The maximum limit on TA may be lower due to device self-heating, which depends on the power dissipation of the specific application. TA (max) = TJ (max) - (THETAJA x PowerDissipation). Refer to the Absolute Maximum Ratings table and the Thermal Characteristics table for TJ and THETAJA. 2. VREGVDD must be tied to AVDD. Both VREGVDD and AVDD minimum voltages must be satisfied for the part to operate. 3. The minimum voltage required in bypass mode is calculated using RBYP from the DCDC specification table. Requirements for other loads can be calculated as VDVDD_min+ILOAD * RBYP_max. 4. When the CSEN peripheral is used with chopping enabled (CSEN_CTRL_CHOPEN = ENABLE), IOVDD must be equal to AVDD. 5. The system designer should consult the characteristic specs of the capacitor used on DECOUPLE to ensure its capacitance value stays within the specified bounds across temperature and DC bias. 6. VSCALE0 to VSCALE2 voltage change transitions occur at a rate of 10 mV / usec for approximately 20 usec. During this transition, peak currents will be dependent on the value of the DECOUPLE output capacitor, from 35 mA (with a 1 F capacitor) to 70 mA (with a 2.7 F capacitor). 4.1.3 Thermal Characteristics Table 4.3. Thermal Characteristics Parameter Symbol Test Condition Min Typ Max Unit Thermal resistance, QFN48 Package THETAJA_QFN48 2-Layer PCB, Air velocity = 0 m/s -- 75.7 -- C/W 2-Layer PCB, Air velocity = 1 m/s -- 61.5 -- C/W 2-Layer PCB, Air velocity = 2 m/s -- 55.4 -- C/W 4-Layer PCB, Air velocity = 0 m/s -- 30.2 -- C/W 4-Layer PCB, Air velocity = 1 m/s -- 26.3 -- C/W 4-Layer PCB, Air velocity = 2 m/s -- 24.9 -- C/W 2-Layer PCB, Air velocity = 0 m/s -- 90.7 -- C/W 2-Layer PCB, Air velocity = 1 m/s -- 73.7 -- C/W 2-Layer PCB, Air velocity = 2 m/s -- 66.4 -- C/W 4-Layer PCB, Air velocity = 0 m/s -- 45 -- C/W 4-Layer PCB, Air velocity = 1 m/s -- 39.6 -- C/W 4-Layer PCB, Air velocity = 2 m/s -- 37.6 -- C/W THETAJA_QFN68 4-Layer PCB, Air velocity = 0 m/s -- 21.5 -- C/W 4-Layer PCB, Air velocity = 1 m/s -- 18.9 -- C/W 4-Layer PCB, Air velocity = 2 m/s -- 17.1 -- C/W Thermal resistance, BGA125 THEPackage TAJA_BGA125 Thermal resistance, QFN68 Package silabs.com | Building a more connected world. Rev. 1.6 | 26 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.4 DC-DC Converter Test conditions: L_DCDC=4.7 H (Murata LQH3NPN4R7MM0L), C_DCDC=4.7 F (Samsung CL10B475KQ8NQNC), V_DCDC_I=3.3 V, V_DCDC_O=1.8 V, I_DCDC_LOAD=50 mA, Heavy Drive configuration, F_DCDC_LN=7 MHz, unless otherwise indicated. Table 4.4. DC-DC Converter Parameter Symbol Test Condition Min Typ Max Unit Input voltage range VDCDC_I Bypass mode, IDCDC_LOAD = 50 mA 1.8 -- VVREGVDD_ V Low noise (LN) mode, 1.8 V output, IDCDC_LOAD = 100 mA, or Low power (LP) mode, 1.8 V output, IDCDC_LOAD = 10 mA 2.4 Low noise (LN) mode, 1.8 V output, IDCDC_LOAD = 200 mA 2.6 Output voltage programmable range1 VDCDC_O Regulation DC accuracy ACCDC Regulation window2 WINREG MAX -- VVREGVDD_ V MAX -- VVREGVDD_ V MAX 1.8 -- VVREGVDD V Low Noise (LN) mode, 1.8 V target output 1.7 -- 1.9 V Low Power (LP) mode, LPCMPBIASEMxx3 = 0, 1.8 V target output, IDCDC_LOAD 75 A 1.63 -- 2.2 V Low Power (LP) mode, LPCMPBIASEMxx3 = 3, 1.8 V target output, IDCDC_LOAD 10 mA 1.63 -- 2.1 V Steady-state output ripple VR Radio disabled -- 3 -- mVpp Output voltage under/overshoot VOV CCM Mode (LNFORCECCM3 = 1), Load changes between 0 mA and 100 mA -- 25 60 mV DCM Mode (LNFORCECCM3 = 0), Load changes between 0 mA and 10 mA -- 45 90 mV Overshoot during LP to LN CCM/DCM mode transitions compared to DC level in LN mode -- 200 -- mV Undershoot during BYP/LP to LN CCM (LNFORCECCM3 = 1) mode transitions compared to DC level in LN mode -- 40 -- mV Undershoot during BYP/LP to LN DCM (LNFORCECCM3 = 0) mode transitions compared to DC level in LN mode -- 100 -- mV DC line regulation VREG Input changes between VVREGVDD_MAX and 2.4 V -- 0.1 -- % DC load regulation IREG Load changes between 0 mA and 100 mA in CCM mode -- 0.1 -- % silabs.com | Building a more connected world. Rev. 1.6 | 27 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Max load current ILOAD_MAX Low noise (LN) mode, Heavy Drive4, T 85 C -- -- 200 mA Low noise (LN) mode, Heavy Drive4, T > 85 C -- -- 100 mA Low noise (LN) mode, Medium Drive4 -- -- 100 mA Low noise (LN) mode, Light Drive4 -- -- 50 mA Low power (LP) mode, LPCMPBIASEMxx3 = 0 -- -- 75 A Low power (LP) mode, LPCMPBIASEMxx3 = 3 -- -- 10 mA CDCDC 25% tolerance 1 4.7 4.7 F DCDC nominal output induc- LDCDC tor 20% tolerance 4.7 4.7 4.7 H -- 1.2 2.5 DCDC nominal output capacitor5 Resistance in Bypass mode RBYP Note: 1. Due to internal dropout, the DC-DC output will never be able to reach its input voltage, VVREGVDD. 2. LP mode controller is a hysteretic controller that maintains the output voltage within the specified limits. 3. LPCMPBIASEMxx refers to either LPCMPBIASEM234H in the EMU_DCDCMISCCTRL register or LPCMPBIASEM01 in the EMU_DCDCLOEM01CFG register, depending on the energy mode. 4. Drive levels are defined by configuration of the PFETCNT and NFETCNT registers. Light Drive: PFETCNT=NFETCNT=3; Medium Drive: PFETCNT=NFETCNT=7; Heavy Drive: PFETCNT=NFETCNT=15. 5. Output voltage under/over-shoot and regulation are specified with CDCDC 4.7 F. Different settings for DCDCLNCOMPCTRL must be used if CDCDC is lower than 4.7 F. See Application Note AN0948 for details. silabs.com | Building a more connected world. Rev. 1.6 | 28 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.5 Current Consumption 4.1.5.1 Current Consumption 3.3 V without DC-DC Converter Unless otherwise indicated, typical conditions are: VREGVDD = AVDD = DVDD = RFVDD = PAVDD = 3.3 V. T = 25 C. DCDC is off. Minimum and maximum values in this table represent the worst conditions across process variation at T = 25 C. Table 4.5. Current Consumption 3.3 V without DC-DC Converter Parameter Symbol Min Typ Max Unit 38.4 MHz crystal, CPU running while loop from flash1 -- 130 -- A/MHz 38 MHz HFRCO, CPU running Prime from flash -- 99 -- A/MHz 38 MHz HFRCO, CPU running while loop from flash -- 99 105 A/MHz 38 MHz HFRCO, CPU running CoreMark from flash -- 124 -- A/MHz 26 MHz HFRCO, CPU running while loop from flash -- 102 108 A/MHz 1 MHz HFRCO, CPU running while loop from flash -- 280 435 A/MHz Current consumption in EM0 IACTIVE_VS mode with all peripherals disabled and voltage scaling enabled 19 MHz HFRCO, CPU running while loop from flash -- 88 -- A/MHz 1 MHz HFRCO, CPU running while loop from flash -- 234 -- A/MHz Current consumption in EM1 IEM1 mode with all peripherals disabled 38.4 MHz crystal1 -- 80 -- A/MHz 38 MHz HFRCO -- 50 54 A/MHz 26 MHz HFRCO -- 52 58 A/MHz 1 MHz HFRCO -- 230 400 A/MHz 19 MHz HFRCO -- 47 -- A/MHz 1 MHz HFRCO -- 193 -- A/MHz Full 256 kB RAM retention and RTCC running from LFXO -- 2.9 -- A Full 256 kB RAM retention and RTCC running from LFRCO -- 3.2 -- A 16 kB (1 bank) RAM retention and RTCC running from LFRCO2 -- 2.1 3.5 A Current consumption in EM3 IEM3_VS mode, with voltage scaling enabled Full 256 kB RAM retention and CRYOTIMER running from ULFRCO -- 2.56 4.8 A Current consumption in EM4H mode, with voltage scaling enabled 128 byte RAM retention, RTCC running from LFXO -- 1.0 -- A 128 byte RAM retention, CRYOTIMER running from ULFRCO -- 0.45 -- A 128 byte RAM retention, no RTCC -- 0.43 0.9 A Current consumption in EM0 IACTIVE mode with all peripherals disabled Current consumption in EM1 IEM1_VS mode with all peripherals disabled and voltage scaling enabled Current consumption in EM2 IEM2_VS mode, with voltage scaling enabled IEM4H_VS silabs.com | Building a more connected world. Test Condition Rev. 1.6 | 29 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Current consumption in EM4S mode IEM4S No RAM retention, no RTCC Min Typ Max Unit -- 0.04 0.1 A Note: 1. CMU_HFXOCTRL_LOWPOWER=0. 2. CMU_LFRCOCTRL_ENVREF = 1, CMU_LFRCOCTRL_VREFUPDATE = 1 silabs.com | Building a more connected world. Rev. 1.6 | 30 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.5.2 Current Consumption 3.3 V using DC-DC Converter Unless otherwise indicated, typical conditions are: VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD = 1.8 V DC-DC output. T = 25 C. Minimum and maximum values in this table represent the worst conditions across process variation at T = 25 C. Table 4.6. Current Consumption 3.3 V using DC-DC Converter Parameter Symbol Min Typ Max Unit 38.4 MHz crystal, CPU running while loop from flash2 -- 88 -- A/MHz 38 MHz HFRCO, CPU running Prime from flash -- 70 -- A/MHz 38 MHz HFRCO, CPU running while loop from flash -- 70 -- A/MHz 38 MHz HFRCO, CPU running CoreMark from flash -- 85 -- A/MHz 26 MHz HFRCO, CPU running while loop from flash -- 77 -- A/MHz 1 MHz HFRCO, CPU running while loop from flash -- 636 -- A/MHz 38.4 MHz crystal, CPU running while loop from flash2 -- 98 -- A/MHz 38 MHz HFRCO, CPU running Prime from flash -- 81 -- A/MHz 38 MHz HFRCO, CPU running while loop from flash -- 82 -- A/MHz 38 MHz HFRCO, CPU running CoreMark from flash -- 95 -- A/MHz 26 MHz HFRCO, CPU running while loop from flash -- 95 -- A/MHz 1 MHz HFRCO, CPU running while loop from flash -- 1155 -- A/MHz Current consumption in EM0 IACTIVE_CCM_VS mode with all peripherals disabled and voltage scaling enabled, DCDC in Low Noise CCM mode3 19 MHz HFRCO, CPU running while loop from flash -- 101 -- A/MHz 1 MHz HFRCO, CPU running while loop from flash -- 1128 -- A/MHz Current consumption in EM1 IEM1_DCM mode with all peripherals disabled, DCDC in Low Noise DCM mode1 38.4 MHz crystal2 -- 59 -- A/MHz 38 MHz HFRCO -- 41 -- A/MHz 26 MHz HFRCO -- 48 -- A/MHz 1 MHz HFRCO -- 610 -- A/MHz 19 MHz HFRCO -- 52 -- A/MHz 1 MHz HFRCO -- 587 -- A/MHz Current consumption in EM0 IACTIVE_DCM mode with all peripherals disabled, DCDC in Low Noise DCM mode1 Current consumption in EM0 IACTIVE_CCM mode with all peripherals disabled, DCDC in Low Noise CCM mode3 Current consumption in EM1 IEM1_DCM_VS mode with all peripherals disabled and voltage scaling enabled, DCDC in Low Noise DCM mode1 silabs.com | Building a more connected world. Test Condition Rev. 1.6 | 31 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Min Typ Max Unit Full 256 kB RAM retention and RTCC running from LFXO -- 2.1 -- A Full 256 kB RAM retention and RTCC running from LFRCO -- 2.2 -- A 16 kB (1 bank) RAM retention and RTCC running from LFRCO5 -- 1.5 -- A Current consumption in EM3 IEM3_VS mode, with voltage scaling enabled Full 256 kB RAM retention and CRYOTIMER running from ULFRCO -- 1.81 -- A Current consumption in EM4H mode, with voltage scaling enabled 128 byte RAM retention, RTCC running from LFXO -- 0.69 -- A 128 byte RAM retention, CRYOTIMER running from ULFRCO -- 0.39 -- A 128 byte RAM retention, no RTCC -- 0.39 -- A No RAM retention, no RTCC -- 0.06 -- A Current consumption in EM2 IEM2_VS mode, with voltage scaling enabled, DCDC in LP mode4 Current consumption in EM4S mode IEM4H_VS IEM4S Test Condition Note: 1. DCDC Low Noise DCM Mode = Light Drive (PFETCNT=NFETCNT=3), F=3.0 MHz (RCOBAND=0), ANASW=DVDD. 2. CMU_HFXOCTRL_LOWPOWER=0. 3. DCDC Low Noise CCM Mode = Light Drive (PFETCNT=NFETCNT=3), F=6.4 MHz (RCOBAND=4), ANASW=DVDD. 4. DCDC Low Power Mode = Medium Drive, LPOSCDIV=1, LPCMPBIASEM234H=0, LPCLIMILIMSEL=1, ANASW=DVDD. 5. CMU_LFRCOCTRL_ENVREF = 1, CMU_LFRCOCTRL_VREFUPDATE = 1 silabs.com | Building a more connected world. Rev. 1.6 | 32 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.5.3 Current Consumption 1.8 V without DC-DC Converter Unless otherwise indicated, typical conditions are: VREGVDD = AVDD = DVDD = RFVDD = PAVDD = 1.8 V. T = 25 C. DCDC is off. Minimum and maximum values in this table represent the worst conditions across process variation at T = 25 C. Table 4.7. Current Consumption 1.8 V without DC-DC Converter Parameter Symbol Min Typ Max Unit 38.4 MHz crystal, CPU running while loop from flash1 -- 130 -- A/MHz 38 MHz HFRCO, CPU running Prime from flash -- 99 -- A/MHz 38 MHz HFRCO, CPU running while loop from flash -- 99 -- A/MHz 38 MHz HFRCO, CPU running CoreMark from flash -- 124 -- A/MHz 26 MHz HFRCO, CPU running while loop from flash -- 102 -- A/MHz 1 MHz HFRCO, CPU running while loop from flash -- 277 -- A/MHz Current consumption in EM0 IACTIVE_VS mode with all peripherals disabled and voltage scaling enabled 19 MHz HFRCO, CPU running while loop from flash -- 87 -- A/MHz 1 MHz HFRCO, CPU running while loop from flash -- 231 -- A/MHz Current consumption in EM1 IEM1 mode with all peripherals disabled 38.4 MHz crystal1 -- 80 -- A/MHz 38 MHz HFRCO -- 50 -- A/MHz 26 MHz HFRCO -- 52 -- A/MHz 1 MHz HFRCO -- 227 -- A/MHz 19 MHz HFRCO -- 47 -- A/MHz 1 MHz HFRCO -- 190 -- A/MHz Full 256 kB RAM retention and RTCC running from LFXO -- 2.8 -- A Full 256 kB RAM retention and RTCC running from LFRCO -- 3.0 -- A 16 kB (1 bank) RAM retention and RTCC running from LFRCO2 -- 1.9 -- A Current consumption in EM3 IEM3_VS mode, with voltage scaling enabled Full 256 kB RAM retention and CRYOTIMER running from ULFRCO -- 2.47 -- A Current consumption in EM4H mode, with voltage scaling enabled 128 byte RAM retention, RTCC running from LFXO -- 0.91 -- A 128 byte RAM retention, CRYOTIMER running from ULFRCO -- 0.35 -- A 128 byte RAM retention, no RTCC -- 0.35 -- A No RAM retention, no RTCC -- 0.04 -- A Current consumption in EM0 IACTIVE mode with all peripherals disabled Current consumption in EM1 IEM1_VS mode with all peripherals disabled and voltage scaling enabled Current consumption in EM2 IEM2_VS mode, with voltage scaling enabled Current consumption in EM4S mode IEM4H_VS IEM4S silabs.com | Building a more connected world. Test Condition Rev. 1.6 | 33 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Note: 1. CMU_HFXOCTRL_LOWPOWER=0. 2. CMU_LFRCOCTRL_ENVREF = 1, CMU_LFRCOCTRL_VREFUPDATE = 1 silabs.com | Building a more connected world. Rev. 1.6 | 34 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.5.4 Current Consumption Using Radio 3.3 V with DC-DC Unless otherwise indicated, typical conditions are: VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD = 1.8 V. T = 25 C. Minimum and maximum values in this table represent the worst conditions across process variation at T = 25 C. Table 4.8. Current Consumption Using Radio 3.3 V with DC-DC Parameter Symbol Test Condition Current consumption in receive mode, active packet reception (MCU in EM1 @ 38.4 MHz, peripheral clocks disabled), T 85 C IRX_ACTIVE Current consumption in receive mode, active packet reception (MCU in EM1 @ 38.4 MHz, peripheral clocks disabled), T > 85 C IRX_ACTIVE_HT silabs.com | Building a more connected world. Min Typ Max Unit 500 kbit/s, 2GFSK, F = 915 MHz, Radio clock prescaled by 4 -- 9.3 10.2 mA 38.4 kbit/s, 2GFSK, F = 868 MHz, Radio clock prescaled by 4 -- 8.6 10.2 mA 38.4 kbit/s, 2GFSK, F = 490 MHz, Radio clock prescaled by 4 -- 8.6 10.2 mA 50 kbit/s, 2GFSK, F = 433 MHz, Radio clock prescaled by 4 -- 8.6 10.2 mA 38.4 kbit/s, 2GFSK, F = 315 MHz, Radio clock prescaled by 4 -- 8.6 10.2 mA 38.4 kbit/s, 2GFSK, F = 169 MHz, Radio clock prescaled by 4 -- 8.4 10.2 mA 1 Mbit/s, 2GFSK, F = 2.4 GHz, Radio clock prescaled by 4 -- 10.0 -- mA 2 Mbit/s, 2GFSK, F = 2.4 GHz, Radio clock prescaled by 4 -- 11.5 -- mA 802.15.4 receiving frame, F = 2.4 GHz, Radio clock prescaled by 3 -- 11 -- mA 500 kbit/s, 2GFSK, F = 915 MHz, Radio clock prescaled by 4 -- -- 13 mA 38.4 kbit/s, 2GFSK, F = 868 MHz, Radio clock prescaled by 4 -- -- 13 mA 38.4 kbit/s, 2GFSK, F = 490 MHz, Radio clock prescaled by 4 -- -- 13 mA 50 kbit/s, 2GFSK, F = 433 MHz, Radio clock prescaled by 4 -- -- 13 mA 38.4 kbit/s, 2GFSK, F = 315 MHz, Radio clock prescaled by 4 -- -- 13 mA 38.4 kbit/s, 2GFSK, F = 169 MHz, Radio clock prescaled by 4 -- -- 13 mA Rev. 1.6 | 35 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Current consumption in reIRX_LISTEN ceive mode, listening for packet (MCU in EM1 @ 38.4 MHz, peripheral clocks disabled), T 85 C Current consumption in reIRX_LISTEN_HT ceive mode, listening for packet (MCU in EM1 @ 38.4 MHz, peripheral clocks disabled), T > 85 C silabs.com | Building a more connected world. Test Condition Min Typ Max Unit 500 kbit/s, 2GFSK, F = 915 MHz, No radio clock prescaling -- 10.2 11 mA 38.4 kbit/s, 2GFSK, F = 868 MHz, No radio clock prescaling -- 9.5 11 mA 38.4 kbit/s, 2GFSK, F = 490 MHz, No radio clock prescaling -- 9.5 11 mA 50 kbit/s, 2GFSK, F = 433 MHz, No radio clock prescaling -- 9.5 11 mA 38.4 kbit/s, 2GFSK, F = 315 MHz, No radio clock prescaling -- 9.4 11 mA 38.4 kbit/s, 2GFSK, F = 169 MHz, No radio clock prescaling -- 9.3 11 mA 1 Mbit/s, 2GFSK, F = 2.4 GHz, No radio clock prescaling -- 10.9 -- mA 2 Mbit/s, 2GFSK, F = 2.4 GHz, No radio clock prescaling -- 11.9 -- mA 802.15.4, F = 2.4 GHz, No radio clock prescaling -- 12.5 -- mA 500 kbit/s, 2GFSK, F = 915 MHz, No radio clock prescaling -- -- 14 mA 38.4 kbit/s, 2GFSK, F = 868 MHz, No radio clock prescaling -- -- 14 mA 38.4 kbit/s, 2GFSK, F = 490 MHz, No radio clock prescaling -- -- 14 mA 50 kbit/s, 2GFSK, F = 433 MHz, No radio clock prescaling -- -- 14 mA 38.4 kbit/s, 2GFSK, F = 315 MHz, No radio clock prescaling -- -- 14 mA 38.4 kbit/s, 2GFSK, F = 169 MHz, No radio clock prescaling -- -- 14 mA Rev. 1.6 | 36 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Current consumption in transmit mode (MCU in EM1 @ 38.4 MHz, peripheral clocks disabled), T 85 C ITX silabs.com | Building a more connected world. Min Typ Max Unit F = 915 MHz, CW, 20 dBm match, External PA supply = 3.3V -- 90.2 134.3 mA F = 915 MHz, CW, 14 dBm match, External PA supply connected to DCDC output -- 36 42.5 mA F = 868 MHz, CW, 20 dBm match, External PA supply = 3.3V -- 79.7 106.7 mA F = 868 MHz, CW, 14 dBm match, External PA supply connected to DCDC output -- 35.3 41 mA F = 490 MHz, CW, 20 dBm match, External PA supply = 3.3V -- 93.8 125.4 mA F = 433 MHz, CW, 10 dBm match, External PA supply connected to DC-DC output -- 20.3 24 mA F = 433 MHz, CW, 14 dBm match, External PA supply connected to DCDC output -- 34 41.5 mA F = 315 MHz, CW, 14 dBm match, External PA supply connected to DCDC output -- 33.5 42 mA F = 169 MHz, CW, 20 dBm match, External PA supply = 3.3V -- 88.6 116.7 mA F = 2.4 GHz, CW, 0 dBm output power, Radio clock prescaled by 3 -- 8.5 -- mA F = 2.4 GHz, CW, 0 dBm output power, Radio clock prescaled by 1 -- 9.5 -- mA F = 2.4 GHz, CW, 3 dBm output power -- 16.5 -- mA F = 2.4 GHz, CW, 8 dBm output power -- 26 -- mA F = 2.4 GHz, CW, 10.5 dBm output power -- 34 -- mA F = 2.4 GHz, CW, 16.5 dBm output power, PAVDD connected directly to external 3.3V supply -- 86 -- mA F = 2.4 GHz, CW, 19.5 dBm output power, PAVDD connected directly to external 3.3V supply -- 131 -- mA Rev. 1.6 | 37 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Current consumption in transmit mode (MCU in EM1 @ 38.4 MHz, peripheral clocks disabled), T > 85 C ITX_HT silabs.com | Building a more connected world. Min Typ Max Unit F = 915 MHz, CW, 20 dBm match, External PA supply = 3.3V -- -- 134.3 mA F = 915 MHz, CW, 14 dBm match, External PA supply connected to DCDC output -- -- 42.5 mA F = 868 MHz, CW, 20 dBm match, External PA supply = 3.3V -- -- 109.8 mA F = 868 MHz, CW, 14 dBm match, External PA supply connected to DCDC output -- -- 41.3 mA F = 490 MHz, CW, 20 dBm match, External PA supply = 3.3V -- -- 130.8 mA F = 433 MHz, CW, 10 dBm match, External PA supply connected to DC-DC output -- -- 24.4 mA F = 433 MHz, CW, 14 dBm match, External PA supply connected to DCDC output -- -- 41.5 mA F = 315 MHz, CW, 14 dBm match, External PA supply connected to DCDC output -- -- 42 mA F = 169 MHz, CW, 20 dBm match, External PA supply = 3.3V -- -- 122.8 mA Rev. 1.6 | 38 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.6 Wake Up Times Table 4.9. Wake Up Times Parameter Symbol Wake up time from EM1 tEM1_WU Wake up from EM2 tEM2_WU Wake up from EM3 tEM3_WU Test Condition Min Typ Max Unit -- 3 -- AHB Clocks Code execution from flash -- 10.1 -- s Code execution from RAM -- 3.2 -- s Code execution from flash -- 10.1 -- s Code execution from RAM -- 3.2 -- s Wake up from EM4H1 tEM4H_WU Executing from flash -- 80 -- s Wake up from EM4S1 tEM4S_WU Executing from flash -- 291 -- s Time from release of reset source to first instruction execution tRESET Soft Pin Reset released -- 43 -- s Any other reset released -- 350 -- s Power mode scaling time tSCALE VSCALE0 to VSCALE2, HFCLK = 19 MHz2 3 -- 31.8 -- s VSCALE2 to VSCALE0, HFCLK = 19 MHz4 -- 4.3 -- s Note: 1. Time from wake up request until first instruction is executed. Wakeup results in device reset. 2. Scaling up from VSCALE0 to VSCALE2 requires approximately 30.3 s + 28 HFCLKs. 3. VSCALE0 to VSCALE2 voltage change transitions occur at a rate of 10 mV/s for approximately 20 s. During this transition, peak currents will be dependent on the value of the DECOUPLE output capacitor, from 35 mA (with a 1 F capacitor) to 70 mA (with a 2.7 F capacitor). 4. Scaling down from VSCALE2 to VSCALE0 requires approximately 2.8 s + 29 HFCLKs. silabs.com | Building a more connected world. Rev. 1.6 | 39 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.7 Brown Out Detector (BOD) Table 4.10. Brown Out Detector (BOD) Parameter Symbol Test Condition Min Typ Max Unit DVDD BOD threshold VDVDDBOD DVDD rising -- -- 1.62 V DVDD falling (EM0/EM1) 1.35 -- -- V DVDD falling (EM2/EM3) 1.3 -- -- V DVDD BOD hysteresis VDVDDBOD_HYST -- 18 -- mV DVDD BOD response time tDVDDBOD_DELAY Supply drops at 0.1V/s rate -- 2.4 -- s AVDD BOD threshold VAVDDBOD -- -- 1.8 V AVDD falling (EM0/EM1) 1.62 -- -- V AVDD falling (EM2/EM3) 1.53 -- -- V AVDD rising AVDD BOD hysteresis VAVDDBOD_HYST -- 20 -- mV AVDD BOD response time tAVDDBOD_DELAY Supply drops at 0.1V/s rate -- 2.4 -- s EM4 BOD threshold VEM4DBOD AVDD rising -- -- 1.7 V AVDD falling 1.45 -- -- V -- 25 -- mV -- 300 -- s EM4 BOD hysteresis VEM4BOD_HYST EM4 BOD response time tEM4BOD_DELAY silabs.com | Building a more connected world. Supply drops at 0.1V/s rate Rev. 1.6 | 40 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.8 Frequency Synthesizer Table 4.11. Frequency Synthesizer Parameter Symbol Test Condition Min Typ Max Unit RF synthesizer frequency range fRANGE 2400 - 2483.5 MHz 2400 -- 2483.5 MHz 779 - 956 MHz 779 -- 956 MHz 584 - 717 MHz 584 -- 717 MHz 358 - 574 MHz 358 -- 574 MHz 191 - 358 MHz 191 -- 358 MHz 110 - 191 MHz 110 -- 191 MHz 2400 - 2483.5 MHz -- -- 73 Hz 779 - 956 MHz -- -- 24 Hz 584 - 717 MHz -- -- 18.3 Hz 358 - 574 MHz -- -- 12.2 Hz 191 - 358 MHz -- -- 7.3 Hz 110 - 191 MHz -- -- 4.6 Hz 2400 - 2483.5 MHz -- -- 73 Hz 779 - 956 MHz -- -- 24 Hz 584 - 717 MHz -- -- 18.3 Hz 358 - 574 MHz -- -- 12.2 Hz 191 - 358 MHz -- -- 7.3 Hz 110 - 191 MHz -- -- 4.6 Hz 2400 - 2483.5 MHz -- -- 1677 kHz 779 - 956 MHz -- -- 559 kHz 584 - 717 MHz -- -- 419 kHz 358 - 574 MHz -- -- 280 kHz 191 - 358 MHz -- -- 167 kHz 110 - 191 MHz -- -- 105 kHz LO tuning frequency resolution with 38.4 MHz crystal Frequency deviation resolution with 38.4 MHz crystal Maximum frequency deviation with 38.4 MHz crystal fRES dfRES dfMAX silabs.com | Building a more connected world. Rev. 1.6 | 41 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.9 2.4 GHz RF Transceiver Characteristics 4.1.9.1 RF Transmitter General Characteristics for 2.4 GHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 2.45 GHz. Table 4.12. RF Transmitter General Characteristics for 2.4 GHz Band Parameter Symbol Test Condition Min Typ Max Unit Maximum TX power1 POUTMAX 19 dBm-rated part numbers. PAVDD connected directly to external 3.3V supply -- 19.5 -- dBm 10 dBm-rated part numbers -- 10.5 -- dBm 0 dBm-rated part numbers -- -- -- dBm -30 -- dBm Minimum active TX Power POUTMIN CW Output power step size POUTSTEP -5 dBm< Output power < 0 dBm -- 1 -- dB 0 dBm < output power < POUTMAX -- 0.5 -- dB 1.8 V < VVREGVDD < 3.3 V, PAVDD connected directly to external supply, for output power > 10 dBm. -- 4.5 -- dB 1.8 V < VVREGVDD < 3.3 V, PAVDD connected directly to external supply, for output power = 10 dBm. -- 3.8 -- dB 1.8 V < VVREGVDD < 3.3 V using DC-DC converter -- 2.2 -- dB From -40 to +85 C, PAVDD connected to DC-DC output -- 1.5 -- dB From -40 to +125 C, PAVDD connected to DC-DC output -- 2.2 -- dB From -40 to +85 C, PAVDD connected to external supply -- 1.5 -- dB From -40 to +125 C, PAVDD connected to external supply -- 3.4 -- dB Over RF tuning frequency range -- 0.4 -- dB 2400 -- 2483.5 MHz Output power variation vs supply at POUTMAX Output power variation vs temperature at POUTMAX POUTVAR_V POUTVAR_T Output power variation vs RF POUTVAR_F frequency at POUTMAX RF tuning frequency range FRANGE Note: 1. Supported transmit power levels are determined by the ordering part number (OPN). Transmit power ratings for all devices covered in this datasheet can be found in the Max TX Power column of the Ordering Information Table. silabs.com | Building a more connected world. Rev. 1.6 | 42 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.9.2 RF Receiver General Characteristics for 2.4 GHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 2.45 GHz. Table 4.13. RF Receiver General Characteristics for 2.4 GHz Band Parameter Symbol RF tuning frequency range FRANGE Receive mode maximum spurious emission SPURRX Test Condition Min Typ Max Unit 2400 -- 2483.5 MHz 30 MHz to 1 GHz -- -57 -- dBm 1 GHz to 12 GHz -- -47 -- dBm Max spurious emissions dur- SPURRX_FCC ing active receive mode, per FCC Part 15.109(a) 216 MHz to 960 MHz, Conducted Measurement -- -55.2 -- dBm Above 960 MHz, Conducted Measurement -- -47.2 -- dBm Level above which RFSENSE will trigger1 RFSENSETRIG CW at 2.45 GHz -- -24 -- dBm Level below which RFSENSE will not trigger1 RFSENSETHRES CW at 2.45 GHz -- -50 -- dBm 1% PER sensitivity SENS2GFSK 2 Mbps 2GFSK signal -- -89.6 -- dBm 250 kbps 2GFSK signal -- -100.7 -- dBm Note: 1. RFSENSE performance is only valid from 0 to 85 C. RFSENSE should be disabled outside this temperature range. silabs.com | Building a more connected world. Rev. 1.6 | 43 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.9.3 RF Transmitter Characteristics for Bluetooth Low Energy in the 2.4GHz Band, 1 Mbps Data Rate Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency = 38.4MHz. RF center frequency 2.45 GHz. Maximum duty cycle of 85%. Table 4.14. RF Transmitter Characteristics for Bluetooth Low Energy in the 2.4GHz Band, 1 Mbps Data Rate Parameter Symbol Test Condition Min Typ Max Unit Transmit 6dB bandwidth TXBW 10 dBm -- 781 -- kHz Power spectral density limit PSDLIMIT Per FCC part 15.247 at 10 dBm -- -8.4 -- dBm/ 3kHz Per FCC part 15.247 at 20 dBm -- -0.4 -- dBm/ 3kHz Per ETSI 300.328 at 10 dBm/1 MHz -- 10.1 -- dBm Occupied channel bandwidth OCPETSI328 per ETSI EN300.328 99% BW at highest and lowest channels in band, 10 dBm -- 1.1 -- MHz In-band spurious emissions, with allowed exceptions1 At 2 MHz, 10 dBm -- -39.5 -- dBm At 3 MHz, 10 dBm -- -44.7 -- dBm At 2 MHz, 20 dBm -- -- -20 dBm At 3 MHz, 20 dBm -- -- -30 dBm SPURINB Emissions of harmonics outof-band, per FCC part 15.247 SPURHRM_FCC 2nd,3rd, 5, 6, 8, 9,10 harmonics; continuous transmission of modulated carrier -- -47 -- dBm Spurious emissions out-ofband, excluding harmonics captured in SPURHARM,FCC. Emissions taken at POUTMAX, PAVDD connected to external 3.3 V supply SPUROOB_FCC Per FCC part 15.205/15.209, Above 2.483 GHz or below 2.4 GHz; continuous transmission of CW carrier, Restricted Bands2 3 -- -47 -- dBm Per FCC part 15.247, Above 2.483 GHz or below 2.4 GHz; continuous transmission of CW carrier, Non-Restricted Bands -- -26 -- dBc Spurious emissions out-ofband; per ETSI 300.328 SPURETSI328 [2400-BW to 2400] MHz, [2483.5 to 2483.5+BW] MHz -- -16 -- dBm [2400-2BW to 2400-BW] MHz, [2483.5+BW to 2483.5+2BW] MHz per ETSI 300.328 -- -26 -- dBm 47-74 MHz,87.5-108 MHz, 174-230 MHz, 470-862 MHz -- -60 -- dBm 25-1000 MHz -- -42 -- dBm 1-12 GHz -- -36 -- dBm Spurious emissions per ETSI SPURETSI440 EN300.440 Note: 1. Per Bluetooth Core_5.0, Vol.6 Part A, Section 3.2.2, exceptions are allowed in up to three bands of 1 MHz width, centered on a frequency which is an integer multiple of 1 MHz. These exceptions shall have an absolute value of -20 dBm or less. 2. For 2476 MHz, 1.5 dB of power backoff is used to achieve this value. 3. For 2478 MHz, 4.2 dB of power backoff is used to achieve this value. silabs.com | Building a more connected world. Rev. 1.6 | 44 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.9.4 RF Receiver Characteristics for Bluetooth Low Energy in the 2.4GHz Band, 1 Mbps Data Rate Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency = 38.4MHz. RF center frequency 2.45 GHz. Table 4.15. RF Receiver Characteristics for Bluetooth Low Energy in the 2.4GHz Band, 1 Mbps Data Rate Parameter Symbol Test Condition Min Typ Max Unit Max usable receiver input level, 0.1% BER SAT Signal is reference signal1. Packet length is 20 bytes. -- 10 -- dBm Sensitivity, 0.1% BER SENS Signal is reference signal1. Using DC-DC converter. -- -94.8 -- dBm With non-ideal signals as specified in RF-PHY.TS.4.2.2, section 4.6.1. -- -94.4 -- dBm Signal to co-channel interfer- C/ICC er, 0.1% BER Desired signal 3 dB above reference sensitivity. -- 10.3 -- dB N+1 adjacent channel selec- C/I1+ tivity, 0.1% BER, with allowable exceptions. Desired is reference signal at -67 dBm Interferer is reference signal at +1 MHz offset. Desired frequency 2402 MHz Fc 2480 MHz -- -1.8 -- dB N-1 adjacent channel selec- C/I1tivity, 0.1% BER, with allowable exceptions. Desired is reference signal at -67 dBm Interferer is reference signal at -1 MHz offset. Desired frequency 2402 MHz Fc 2480 MHz -- -0.7 -- dB Alternate selectivity, 0.1% BER, with allowable exceptions. Desired is reference signal at -67 dBm Interferer is reference signal at 2 MHz offset. Desired frequency 2402 MHz Fc 2480 MHz, QFN48 and BGA125 packages. -- -40.6 -- dB Interferer is reference signal at 2 MHz offset. Desired frequency 2402 MHz Fc 2480 MHz, QFN68 package. -- -34.1 -- dB Interferer is reference signal at 3 MHz offset. Desired frequency 2404 MHz Fc 2480 MHz -- -46.2 -- dB Selectivity to image frequen- C/IIM cy, 0.1% BER. Desired is reference signal at -67 dBm Interferer is reference signal at image frequency with 1 MHz precision -- -38.1 -- dB Selectivity to image frequency 1 MHz, 0.1% BER. Desired is reference signal at -67 dBm Interferer is reference signal at image frequency 1 MHz with 1 MHz precision -- -46.5 -- dB Alternate selectivity, 0.1% BER, with allowable exceptions. Desired is reference signal at -67 dBm C/I2 C/I3 C/IIM+1 silabs.com | Building a more connected world. Rev. 1.6 | 45 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Blocking, less than 0.1% BLOCKOOB BER. Desired is -67dBm BLE reference signal at 2426MHz. Interferer is CW in OOB range2 Intermodulation performance IM Test Condition Min Typ Max Unit Interferer frequency 30 MHz f 2000 MHz -5 -- -- dBm Interferer frequency 2003 MHz f 2399 MHz -24 -- -- dBm Interferer frequency 2484 MHz f 2997 MHz -10 -- -- dBm Interferer frequency 3 GHz f 6 GHz -10 -- -- dBm Interferer frequency 6 GHz f 12.75 GHz -17 -- -- dBm Per Core_4.1, Vol 6, Part A, Section 4.4 with n = 3 -- -23.7 -- dBm Note: 1. Reference signal is defined 2GFSK at -67 dBm, Modulation index = 0.5, BT = 0.5, Bit rate = 1 Mbps, desired data = PRBS9; interferer data = PRBS15; frequency accuracy better than 1 ppm. 2. Interferer max power limited by equipment capabilities and path loss. Minimum specified at 25 C. silabs.com | Building a more connected world. Rev. 1.6 | 46 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.9.5 RF Transmitter Characteristics for Bluetooth Low Energy in the 2.4GHz Band, 2 Mbps Data Rate Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency = 38.4MHz. RF center frequency 2.45 GHz. Maximum duty cycle of 85%. Table 4.16. RF Transmitter Characteristics for Bluetooth Low Energy in the 2.4GHz Band, 2 Mbps Data Rate Parameter Symbol Test Condition Min Typ Max Unit Transmit 6dB bandwidth TXBW 10 dBm -- 1404 -- kHz Power spectral density limit PSDLIMIT Per FCC part 15.247 at 10 dBm -- -12.3 -- dBm/ 3kHz Per FCC part 15.247 at 20 dBm -- -4.0 -- dBm/ 3kHz Per ETSI 300.328 at 10 dBm/1 MHz -- 11.3 -- dBm Occupied channel bandwidth OCPETSI328 per ETSI EN300.328 99% BW at highest and lowest channels in band, 10 dBm -- 2.1 -- MHz In-band spurious emissions, with allowed exceptions1 At 4 MHz, 10 dBm -- -40.3 -- dBm At 6 MHz, 10 dBm -- -43.6 -- dBm At 4 MHz, 20 dBm -- -32.3 -- dBm At 6 MHz, 20 dBm -- -35.6 -- dBm SPURINB Emissions of harmonics outof-band, per FCC part 15.247 SPURHRM_FCC 2nd,3rd, 5, 6, 8, 9,10 harmonics; continuous transmission of modulated carrier -- -47 -- dBm Spurious emissions out-ofband, excluding harmonics captured in SPURHARM,FCC. Emissions taken at POUTMAX, PAVDD connected to external 3.3 V supply SPUROOB_FCC Per FCC part 15.205/15.209, Above 2.483 GHz or below 2.4 GHz; continuous transmission of CW carrier, Restricted Bands2 3 4 -- -47 -- dBm Per FCC part 15.247, Above 2.483 GHz or below 2.4 GHz; continuous transmission of CW carrier, Non-Restricted Bands -- -26 -- dBc Spurious emissions out-ofband; per ETSI 300.328 SPURETSI328 [2400-BW to 2400] MHz, [2483.5 to 2483.5+BW] MHz -- -16 -- dBm [2400-2BW to 2400-BW] MHz, [2483.5+BW to 2483.5+2BW] MHz per ETSI 300.328 -- -26 -- dBm 47-74 MHz,87.5-108 MHz, 174-230 MHz, 470-862 MHz -- -60 -- dBm 25-1000 MHz -- -42 -- dBm 1-12 GHz -- -36 -- dBm 5 Spurious emissions per ETSI SPURETSI440 EN300.440 silabs.com | Building a more connected world. Rev. 1.6 | 47 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Note: 1. Per Bluetooth Core_5.0, Vol.6 Part A, Section 3.2.2, exceptions are allowed in up to three bands of 1 MHz width, centered on a frequency which is an integer multiple of 1 MHz. These exceptions shall have an absolute value of -20 dBm or less. 2. For 2472 MHz, 1.3 dB of power backoff is used to achieve this value. 3. For 2474 MHz, 3.8 dB of power backoff is used to achieve this value. 4. For 2476 MHz, 7 dB of power backoff is used to achieve this value. 5. For 2478 MHz, 11.2 dB of power backoff is used to achieve this value. silabs.com | Building a more connected world. Rev. 1.6 | 48 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.9.6 RF Receiver Characteristics for Bluetooth Low Energy in the 2.4GHz Band, 2 Mbps Data Rate Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency = 38.4MHz. RF center frequency 2.45 GHz1. Table 4.17. RF Receiver Characteristics for Bluetooth Low Energy in the 2.4GHz Band, 2 Mbps Data Rate Parameter Symbol Test Condition Min Typ Max Unit Max usable receiver input level, 0.1% BER SAT Signal is reference signal2. Packet length is 20 bytes. -- 10 -- dBm Sensitivity, 0.1% BER SENS Signal is reference signal2. Using DC-DC converter. QFN48 and BGA125 packages. -- -91.3 -- dBm With non-ideal signals as specified in RF-PHY.TS.4.2.2, section 4.6.1. QFN48 and BGA125 packages. -- -91 -- dBm Signal is reference signal2. Using DC-DC converter. QFN68 package. -- -91.3 -- dBm With non-ideal signals as specified in RF-PHY.TS.4.2.2, section 4.6.1. QFN68 package. -- -90.1 -- dBm Signal to co-channel interfer- C/ICC er, 0.1% BER Desired signal 3 dB above reference sensitivity. -- 7.3 -- dB N+1 adjacent channel selec- C/I1+ tivity, 0.1% BER, with allowable exceptions. Desired is reference signal at -67 dBm Interferer is reference signal at +2 MHz offset. Desired frequency 2402 MHz Fc 2480 MHz -- -10.4 -- dB N-1 adjacent channel selec- C/I1tivity, 0.1% BER, with allowable exceptions. Desired is reference signal at -67 dBm Interferer is reference signal at -2 MHz offset. Desired frequency 2402 MHz Fc 2480 MHz -- -13.9 -- dB Alternate selectivity, 0.1% BER, with allowable exceptions. Desired is reference signal at -67 dBm C/I2 Interferer is reference signal at 4 MHz offset. Desired frequency 2402 MHz Fc 2480 MHz -- -40.9 -- dB Alternate selectivity, 0.1% BER, with allowable exceptions. Desired is reference signal at -67 dBm C/I3 Interferer is reference signal at 6 MHz offset. Desired frequency 2404 MHz Fc 2480 MHz -- -43.7 -- dB Selectivity to image frequen- C/IIM cy, 0.1% BER. Desired is reference signal at -67 dBm Interferer is reference signal at image frequency with 1 MHz precision -- -10.4 -- dB Selectivity to image frequency 2 MHz, 0.1% BER. Desired is reference signal at -67 dBm Interferer is reference signal at image frequency 2 MHz with 2 MHz precision -- -40.9 -- dB Per Core_4.1, Vol 6, Part A, Section 4.4 with n = 3 -- -25.1 -- dBm C/IIM+1 Intermodulation performance IM silabs.com | Building a more connected world. Rev. 1.6 | 49 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Note: 1. For the BLE 2Mbps in-band blocking performance, there may be up to 5 spurious response channels where the requirement of 30.8% PER is not met and therefore an exception will need to be taken for each of these frequencies to meet the requirements of the BLE standard. 2. Reference signal is defined 2GFSK at -67 dBm, Modulation index = 0.5, BT = 0.5, Bit rate = 2 Mbps, desired data = PRBS9; interferer data = PRBS15; frequency accuracy better than 1 ppm. silabs.com | Building a more connected world. Rev. 1.6 | 50 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.9.7 RF Transmitter Characteristics for 802.15.4 DSSS-OQPSK in the 2.4 GHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 2.45 GHz. Maximum duty cycle of 66%. Table 4.18. RF Transmitter Characteristics for 802.15.4 DSSS-OQPSK in the 2.4 GHz Band Parameter Symbol Test Condition Min Typ Max Unit Error vector magnitude (off- EVM set EVM), per 802.15.4-2011 Average across frequency. Signal is DSSS-OQPSK reference packet1 -- 3.8 -- % rms Power spectral density limit Relative, at carrier 3.5 MHz, output power at POUTMAX -- -26 -- dBc/ 100kHz Absolute, at carrier 3.5 MHz, output power at POUTMAX2 -- -36 -- dBm/ 100kHz Per FCC part 15.247, output power at POUTMAX -- -4 -- dBm/ 3kHz ETSI -- 12.1 -- dBm Occupied channel bandwidth OCPETSI328 per ETSI EN300.328 99% BW at highest and lowest channels in band -- 2.25 -- MHz Spurious emissions of harSPURHRM_FCC_ monics in restricted bands R per FCC Part 15.205/15.209, Emissions taken at POUTMAX, PAVDD connected to external 3.3 V supply, Test Frequency is 2450 MHz Continuous transmission of modulated carrier -- -45.8 -- dBm Spurious emissions of harSPURHRM_FCC_ monics in non-restricted NRR bands per FCC Part 15.247/15.35, Emissions taken at POUTMAX, PAVDD connected to external 3.3 V supply, Test Frequency is 2450 MHz Continuous transmission of modulated carrier -- -26 -- dBc Spurious emissions out-ofband (above 2.483 GHz or below 2.4 GHz) in restricted bands, per FCC part 15.205/15.209, Emissions taken at POUTMAX, PAVDD connected to external 3.3 V supply, Test Frequency = 2450 MHz Restricted bands 30-88 MHz; continuous transmission of modulated carrier -- -61 -- dBm Restricted bands 88-216 MHz; continuous transmission of modulated carrier -- -58 -- dBm Restricted bands 216-960 MHz; continuous transmission of modulated carrier -- -55 -- dBm Restricted bands >960 MHz; continuous transmission of modulated carrier3 4 -- -47 -- dBm PSDLIMIT SPUROOB_FCC_ R silabs.com | Building a more connected world. Rev. 1.6 | 51 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Spurious emissions out-ofSPUROOB_FCC_ band in non-restricted bands NR per FCC Part 15.247, Emissions taken at POUTMAX, PAVDD connected to external 3.3 V supply, Test Frequency = 2450 MHz Above 2.483 GHz or below 2.4 GHz; continuous transmission of modulated carrier -- -26 -- dBc Spurious emissions out-ofband; per ETSI 300.3285 [2400-BW to 2400], [2483.5 to 2483.5+BW]; -- -16 -- dBm [2400-2BW to 2400-BW], [2483.5+BW to 2483.5+2BW]; per ETSI 300.328 -- -26 -- dBm 47-74 MHz,87.5-108 MHz, 174-230 MHz, 470-862 MHz -- -60 -- dBm 25-1000 MHz, excluding above frequencies -- -42 -- dBm 1G-14G -- -36 -- dBm SPURETSI328 Spurious emissions per ETSI SPURETSI440 EN300.4405 Note: 1. Reference packet is defined as 20 octet PSDU, modulated according to 802.15.4-2011 DSSS-OQPSK in the 2.4GHz band, with pseudo-random packet data content. 2. For 2415 MHz, 2 dB of power backoff is used to achieve this value. 3. For 2475 MHz, 2 dB of power backoff is used to achieve this value. 4. For 2480 MHz, 13 dB of power backoff is used to achieve this value. 5. Specified at maximum power output level of 10 dBm. silabs.com | Building a more connected world. Rev. 1.6 | 52 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.9.8 RF Receiver Characteristics for 802.15.4 DSSS-OQPSK in the 2.4 GHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = PAVDD. RFVDD and PAVDD path is filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 2.45 GHz. Table 4.19. RF Receiver Characteristics for 802.15.4 DSSS-OQPSK in the 2.4 GHz Band Parameter Symbol Test Condition Min Typ Max Unit Max usable receiver input level, 1% PER SAT Signal is reference signal1. Packet length is 20 octets. -- 10 -- dBm Sensitivity, 1% PER SENS Signal is reference signal. Packet length is 20 octets. Using DC-DC converter. -- -102.7 -- dBm Signal is reference signal. Packet length is 20 octets. Without DCDC converter. -- -102.7 -- dBm Co-channel interferer rejection, 1% PER CCR Desired signal 3 dB above sensitivity limit -- -4.6 -- dB High-side adjacent channel rejection, 1% PER. Desired is reference signal at 3dB above reference sensitivity level2 ACRP1 Interferer is reference signal at +1 channel-spacing. -- 40.7 -- dB Interferer is filtered reference signal3 at +1 channel-spacing. -- 47 -- dB Interferer is CW at +1 channelspacing4. -- 54.3 -- dB Interferer is reference signal at -1 channel-spacing. -- 40.8 -- dB Interferer is filtered reference signal3 at -1 channel-spacing. -- 47.5 -- dB Interferer is CW at -1 channelspacing. -- 56.5 -- dB Interferer is reference signal at 2 channel-spacing -- 51.5 -- dB Interferer is filtered reference signal3 at 2 channel-spacing -- 53.7 -- dB Interferer is CW at 2 channelspacing -- 62.4 -- dB Image rejection , 1% PER, IR Desired is reference signal at 3dB above reference sensitivity level2 Interferer is CW in image band4 -- 50.4 -- dB Blocking rejection of all other BLOCK channels. 1% PER, Desired is reference signal at 3dB above reference sensitivity level2. Interferer is reference signal Interferer frequency < Desired frequency - 3 channel-spacing -- 58.5 -- dB Interferer frequency > Desired frequency + 3 channel-spacing -- 56.4 -- dB Blocking rejection of 802.11g BLOCK80211G signal centered at +12MHz or -13MHz5 Desired is reference signal at 6dB above reference sensitivity level2 -- 53 -- dB Low-side adjacent channel rejection, 1% PER. Desired is reference signal at 3dB above reference sensitivity level2 Alternate channel rejection, 1% PER. Desired is reference signal at 3dB above reference sensitivity level2 ACRM1 ACR2 silabs.com | Building a more connected world. Rev. 1.6 | 53 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Min Typ Max Unit Upper limit of input power RSSIMAX range over which RSSI resolution is maintained -- -- 5 dBm Lower limit of input power RSSIMIN range over which RSSI resolution is maintained -98 -- -- dBm -- 0.25 -- dB -- +/-6 -- dB RSSI resolution RSSIRES RSSI accuracy in the linear region as defined by 802.15.4-2003 RSSILIN Test Condition over RSSIMIN to RSSIMAX Note: 1. Reference signal is defined as O-QPSK DSSS per 802.15.4, Frequency range = 2400-2483.5 MHz, Symbol rate = 62.5 ksymbols/s. 2. Reference sensitivity level is -85 dBm. 3. Filter is characterized as a symmetric bandpass centered on the adjacent channel having a 3dB bandwidth of 4.6 MHz and stopband rejection better than 26 dB beyond 3.15 MHz from the adjacent carrier. 4. Due to low-IF frequency, there is some overlap of adjacent channel and image channel bands. Adjacent channel CW blocker tests place the Interferer center frequency at the Desired frequency 5 MHz on the channel raster, whereas the image rejection test places the CW interferer near the image frequency of the Desired signal carrier, regardless of the channel raster. 5. This is an IEEE 802.11b/g ERP-PBCC 22 MBit/s signal as defined by the IEEE 802.11 specification and IEEE 802.11g addendum. silabs.com | Building a more connected world. Rev. 1.6 | 54 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.10 Sub-GHz RF Transceiver Characteristics silabs.com | Building a more connected world. Rev. 1.6 | 55 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.10.1 Sub-GHz RF Transmitter characteristics for 915 MHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = External PA Supply. RFVDD and external PA supply paths filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 915 MHz. Table 4.20. Sub-GHz RF Transmitter characteristics for 915 MHz Band Parameter Symbol RF tuning frequency range FRANGE Maximum TX Power1 POUTMAX Test Condition External PA supply = 3.3V, 20 dBm output power setting External PA supply connected to DC-DC output, 14 dBm output power setting Min Typ Max Unit 902 -- 930 MHz 18 19.8 23.3 dBm 12.6 14.2 16.1 dBm -- -45.5 -- dBm Minimum active TX Power POUTMIN Output power step size POUTSTEP output power > 0 dBm -- 0.5 -- dB Output power variation vs supply at POUTMAX POUTVAR_V 1.8 V < VVREGVDD < 3.3 V, External PA supply = 3.3 V, T = 25 C -- 4.8 -- dB 1.8 V < VVREGVDD < 3.3 V, External PA supply connected to DCDC output, T = 25 C -- 1.9 -- dB -40 to +85 C with External PA supply = 3.3 V -- 0.6 1.3 dB -40 to +85 C with External PA supply connected to DC-DC output -- 0.7 1.4 dB External PA supply = 3.3 V, T = 25 C -- 0.2 0.6 dB External PA supply connected to DC-DC output, T = 25 C -- 0.3 0.6 dB SPURHARM_FCC In restricted bands, per FCC Part 15.205 / 15.209 _20 -- -45 -42 dBm In non-restricted bands, per FCC Part 15.247 -- -26 -20 dBc In non-restricted bands, per FCC Part 15.247 -- -26 -20 dBc In restricted bands (30-88 MHz), per FCC Part 15.205 / 15.209 -- -62 -56 dBm In restricted bands (88-216 MHz), per FCC Part 15.205 / 15.209 -- -61 -56 dBm In restricted bands (216-960 MHz), per FCC Part 15.205 / 15.209 -- -58 -52 dBm In restricted bands (>960 MHz), per FCC Part 15.205 / 15.209 -- -47 -42 dBm Output power variation vs temperature, peak to peak POUTVAR_T Output power variation vs RF POUTVAR_F frequency Spurious emissions of harmonics at 20 dBm output power, Conducted measurement, 20dBm match, External PA supply = 3.3V, Test Frequency = 915 MHz Spurious emissions out-ofSPUROOB_FCC_ band at 20 dBm output pow- 20 er, Conducted measurement, 20dBm match, External PA supply = 3.3V, Test Frequency = 915 MHz silabs.com | Building a more connected world. Rev. 1.6 | 56 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Spurious emissions of harmonics at 14 dBm output power, Conducted measurement, 14dBm match, External PA supply connected to DC-DC output, Test Frequency = 915 MHz SPURHARM_FCC In restricted bands, per FCC Part 15.205 / 15.209 _14 -- -47 -42 dBm In non-restricted bands, per FCC Part 15.247 -- -26 -20 dBc In non-restricted bands, per FCC Part 15.247 -- -26 -20 dBc In restricted bands (30-88 MHz), per FCC Part 15.205 / 15.209 -- -62 -56 dBm In restricted bands (88-216 MHz), per FCC Part 15.205 / 15.209 -- -61 -56 dBm In restricted bands (216-960 MHz), per FCC Part 15.205 / 15.209 -- -58 -52 dBm In restricted bands (>960 MHz), per FCC Part 15.205 / 15.209 -- -45 -42 dBm Error vector magnitude (off- EVM set EVM), per 802.15.4-2011 Signal is DSSS-OQPSK reference packet. Modulated according to 802.15.4-2011 DSSS-OQPSK in the 915MHz band, with pseudorandom packet data content. External PA supply = 3.3V. -- 1.0 2.8 %rms PSD Relative, at carrier 1.2 MHz. Average spectral power shall be measured using a 100kHz resolution bandwidth. The reference level shall be the highest average spectral power measured within 600kHz of the carrier frequency. External PA supply = 3.3V. -- -37.1 -24.8 dBc/ 100kHz Absolute, at carrier 1.2 MHz. Average spectral power shall be measured using a 100kHz resolution bandwidth. External PA supply = 3.3V. -- -24.2 -20 dBm/ 100kHz Spurious emissions out-ofSPUROOB_FCC_ band at 14 dBm output pow- 14 er, Conducted measurement, 14dBm match, External PA supply connected to DC-DC output, Test Frequency = 915 MHz Power spectral density limit2 Note: 1. Supported transmit power levels are determined by the ordering part number (OPN). Transmit power ratings for all devices covered in this datasheet can be found in the Max TX Power column of the Ordering Information Table. 2. Definition of reference signal is O-QPSK DSSS per 802.15.4, Frequency Range = 902-928 MHz, Data rate = 250 kbps, 16-chip PN sequence mapping. silabs.com | Building a more connected world. Rev. 1.6 | 57 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.10.2 Sub-GHz RF Receiver Characteristics for 915 MHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = External PA Supply. RFVDD and external PA supply paths filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 915 MHz. Table 4.21. Sub-GHz RF Receiver Characteristics for 915 MHz Band Parameter Symbol Tuning frequency range FRANGE Test Condition Min Typ Max Unit 902 -- 930 MHz Max usable input level, 0.1% SAT500K BER Desired is reference 500 kbps GFSK signal1 -- 10 -- dBm Sensitivity Desired is reference 4.8 kbps OOK signal2, 20% PER, T 85 C -- -105.2 -100.7 dBm Desired is reference 600 bps GFSK signal3, 0.1% BER -- -126.2 -- dBm Desired is reference 50 kbps GFSK signal4, 0.1% BER, T 85 C -- -108.2 -104.2 dBm Desired is reference 100 kbps GFSK signal5, 0.1% BER, T 85 C -- -105.1 -101.5 dBm Desired is reference 500 kbps GFSK signal1, 0.1% BER, T 85 C -- -98.2 -93.2 dBm Desired is reference 400 kbps 4GFSK signal6, 1% PER, T 85 C -- -95.2 -91 dBm Desired is reference O-QPSK DSSS signal7, 1% PER, Payload length is 20 octets -- -100.1 -- dBm SENS Level above which RFSENSE will trigger8 RFSENSETRIG CW at 915 MHz -- -28.1 -- dBm Level below which RFSENSE will not trigger8 RFSENSETHRES CW at 915 MHz -- -50 -- dBm silabs.com | Building a more connected world. Rev. 1.6 | 58 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Adjacent channel selectivity, Interferer is CW at 1 x channel-spacing C/I1 Alternate channel selectivity, C/I2 Interferer is CW at 2 x channel-spacing silabs.com | Building a more connected world. Min Typ Max Unit Desired is 4.8 kbps OOK signal2 at 3dB above sensitivity level, 20% PER -- 48.1 -- dB Desired is 600 bps GFSK signal3 at 3dB above sensitivity level, 0.1% BER -- 71.4 -- dB Desired is 50 kbps GFSK signal4 at 3dB above sensitivity level, 0.1% BER -- 49.8 -- dB Desired is 100 kbps GFSK signal5 at 3dB above sensitivity level, 0.1% BER -- 51.1 -- dB Desired is 500 kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 48.1 -- dB Desired is 400 kbps 4GFSK signal6 at 3dB above sensitivity level, 0.1% BER -- 41.4 -- dB Desired is reference O-QPSK DSSS signal7 at 3dB above sensitivity level, 1% PER -- 49.1 -- dB Desired is 4.8 kbps OOK signal2 at 3dB above sensitivity level, 20% PER -- 56.3 -- dB Desired is 600 bps GFSK signal3 at 3dB above sensitivity level, 0.1% BER -- 74.7 -- dB Desired is 50 kbps GFSK signal4 at 3dB above sensitivity level, 0.1% BER -- 55.8 -- dB Desired is 100 kbps GFSK signal5 at 3dB above sensitivity level, 0.1% BER -- 56.4 -- dB Desired is 500 kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 51.8 -- dB Desired is 400 kbps 4GFSK signal6 at 3dB above sensitivity level, 0.1% BER -- 46.8 -- dB Desired is reference O-QPSK DSSS signal7 at 3dB above sensitivity level, 1% PER -- 57.7 -- dB Rev. 1.6 | 59 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Image rejection, Interferer is CW at image frequency C/IIMAGE Desired is 4.8 kbps OOK signal2 at 3dB above sensitivity level, 20% PER -- 48.4 -- dB Desired is 50 kbps GFSK signal4 at 3dB above sensitivity level, 0.1% BER -- 54.9 -- dB Desired is 100 kbps GFSK signal5 at 3dB above sensitivity level, 0.1% BER -- 49.1 -- dB Desired is 500 kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 47.9 -- dB Desired is 400 kbps 4GFSK signal6 at 3dB above sensitivity level, 0.1% BER -- 42.8 -- dB Desired is reference O-QPSK DSSS signal7 at 3dB above sensitivity level, 1% PER -- 48.9 -- dB Interferer CW at Desired 1 MHz -- 58.7 -- dB Interferer CW at Desired 2 MHz -- 62.5 -- dB Interferer CW at Desired 10 MHz -- 76.4 -- dB Desired is 100 kbps GFSK signal5 at 3dB above sensitivity level -- 45 -- dB Upper limit of input power RSSIMAX range over which RSSI resolution is maintained -- -- 5 dBm Lower limit of input power RSSIMIN range over which RSSI resolution is maintained -98 -- -- dBm Over RSSIMIN to RSSIMAX range -- 0.25 -- dBm Max spurious emissions dur- SPURRX_FCC ing active receive mode, per FCC Part 15.109(a) 216-960 MHz -- -55 -49.2 dBm Above 960 MHz -- -47 -41.2 dBm Max spurious emissions dur- SPURRX_ARIB ing active receive mode,per ARIB STD-T108 Section 3.3 Below 710 MHz, RBW=100kHz -- -60 -54 dBm 710-900 MHz, RBW=1MHz -- -61 -55 dBm 900-915 MHz, RBW=100kHz -- -61 -55 dBm 915-930 MHz, RBW=100kHz -- -61 -55 dBm 930-1000 MHz, RBW=100kHz -- -61 -55 dBm Above 1000 MHz, RBW=1MHz -- -53 -47 dBm Blocking selectivity, 0.1% BER. Desired is 100 kbps GFSK signal at 3dB above sensitivity level C/IBLOCKER Intermod selectivity, 0.1% BER. CW interferers at 400 kHz and 800 kHz offsets C/IIM RSSI resolution RSSIRES silabs.com | Building a more connected world. Rev. 1.6 | 60 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Note: 1. Definition of reference signal is 500 kbps 2GFSK, BT=0.5, f = 175 kHz, RX channel BW = 835.076 kHz, channel spacing = 1 MHz. 2. Definition of reference signal is 4.8 kbps OOK, RX channel BW = 306.036 kHz, channel spacing = 500 kHz. 3. Definition of reference signal is 600 bps 2GFSK, BT=0.5, f = 0.3 kHz, RX channel BW = 1.2 kHz, channel spacing = 300 kHz. 4. Definition of reference signal is 50 kbps 2GFSK, BT=0.5, f = 25 kHz, RX channel BW = 99.012 kHz, channel spacing = 200 kHz. 5. Definition of reference signal is 100 kbps 2GFSK, BT=0.5, f = 50 kHz, RX channel BW = 198.024 kHz, channel spacing = 400 kHz. 6. Definition of reference signal is 400 kbps 4GFSK, BT=0.5, inner deviation = 33.3 kHz, RX channel BW = 368.920 kHz, channel spacing = 600 kHz. 7. Definition of reference signal is O-QPSK DSSS per 802.15.4, Frequency Range = 902-928 MHz, Data rate = 250 kbps, 16-chip PN sequence mapping. 8. RFSENSE performance is only valid from 0 to 85 C. RFSENSE should be disabled outside this temperature range. silabs.com | Building a more connected world. Rev. 1.6 | 61 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.10.3 Sub-GHz RF Transmitter characteristics for 868 MHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = External PA Supply. RFVDD and external PA supply paths filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 868 MHz. Table 4.22. Sub-GHz RF Transmitter characteristics for 868 MHz Band Parameter Symbol RF tuning frequency range FRANGE Maximum TX Power1 POUTMAX Test Condition Min Typ Max Unit 863 -- 876 MHz External PA supply = 3.3V, 20 dBm output power setting, T 85 C 17.1 19.3 22.9 dBm External PA supply connected to DC-DC output, 14 dBm output power setting 11.4 13.7 16.5 dBm -- -43.5 -- dBm Minimum active TX Power POUTMIN Output power step size POUTSTEP output power > 0 dBm -- 0.5 -- dB Output power variation vs supply at POUTMAX POUTVAR_V 1.8 V < VVREGVDD < 3.3 V, External PA supply = 3.3 V, T = 25 C -- 5 -- dB 1.8 V < VVREGVDD < 3.3 V, External PA supply connected to DCDC output, T = 25 C -- 2 -- dB -40 to +85 C with External PA supply = 3.3 V -- 0.6 0.9 dB -40 to +85 C with External PA supply connected to DC-DC output -- 0.5 1.2 dB External PA supply = 3.3 V, T = 25 C -- 0.2 0.6 dB External PA supply connected to DC-DC output, T = 25 C -- 0.2 0.8 dB Spurious emissions of harmonics, Conducted measurement, Test Frequency = 868 MHz SPURHARM_ETSI Per ETSI EN 300-220, Section 7.8.2.1, External PA supply connected to: DCDC at 14 dBm, or 3.3 V at 19.5 dBm -- -35 -30 dBm Spurious emissions out-ofband, Conducted measurement, Test Frequency = 868 MHz SPUROOB_ETSI Per ETSI EN 300-220, Section 7.8.2.1 (47-74 MHz, 87.5-118 MHz, 174-230 MHz, and 470-862 MHz), External PA supply connected to: DCDC at 14 dBm, or 3.3 V at 19.5 dBm -- -59 -54 dBm Per ETSI EN 300-220, Section 7.8.2.1 (other frequencies below 1 GHz), External PA supply connected to: DCDC at 14 dBm, or 3.3 V at 19.5 dBm -- -42 -36 dBm Per ETSI EN 300-220, Section 7.8.2.1 (frequencies above 1 GHz), External PA supply connected to: DCDC at 14 dBm, or 3.3 V at 19.5 dBm -- -36 -30 dBm Output power variation vs temperature, peak to peak POUTVAR_T Output power variation vs RF POUTVAR_F frequency silabs.com | Building a more connected world. Rev. 1.6 | 62 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Error vector magnitude (off- EVM set EVM), per 802.15.4-2015 Test Condition Signal is DSSS-BPSK reference packet. Modulated according to 802.15.4-2015 DSSS-BPSK in the 868MHz band, with pseudo-random packet data content. External PA supply connected to external 3.3V supply Min Typ Max Unit -- 5.7 -- %rms Note: 1. Supported transmit power levels are determined by the ordering part number (OPN). Transmit power ratings for all devices covered in this datasheet can be found in the Max TX Power column of the Ordering Information Table. silabs.com | Building a more connected world. Rev. 1.6 | 63 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.10.4 Sub-GHz RF Receiver Characteristics for 868 MHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = External PA Supply. RFVDD and external PA supply paths filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 868 MHz. Table 4.23. Sub-GHz RF Receiver Characteristics for 868 MHz Band Parameter Symbol Tuning frequency range FRANGE Test Condition Min Typ Max Unit 863 -- 876 MHz Max usable input level, 0.1% SAT2k4 BER Desired is reference 2.4 kbps GFSK signal1 -- 10 -- dBm Max usable input level, 0.1% SAT38k4 BER Desired is reference 38.4 kbps GFSK signal2 -- 10 -- dBm Sensitivity Desired is reference 2.4 kbps GFSK signal1, 0.1% BER -- -120.6 -- dBm Desired is reference 38.4 kbps GFSK signal2, 0.1% BER, T 85 C -- -109.5 -105.4 dBm Desired is reference 500 kbps GFSK signal3, 0.1% BER -- -96.4 -- dBm Desired is reference BPSK signal4, 1% PER -- -110.6 -- dBm SENS Level above which RFSENSE will trigger5 RFSENSETRIG CW at 868 MHz -- -28.1 -- dBm Level below which RFSENSE will not trigger5 RFSENSETHRES CW at 868 MHz -- -50 -- dBm Adjacent channel selectivity, Interferer is CW at 1 x channel-spacing C/I1 Desired is 2.4 kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER 44.5 56.9 -- dB Desired is 38.4kbps GFSK signal2 at 3dB above sensitivity level, 0.1% BER 35.4 43 -- dB Desired is 2.4kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 56.8 -- dB Desired is 38.4kbps GFSK signal2 at 3dB above sensitivity level, 0.1% BER -- 48.2 -- dB Desired is 2.4kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 50.2 -- dB Desired is 38.4kbps GFSK signal2 at 3dB above sensitivity level, 0.1% BER -- 48.7 -- dB Interferer CW at Desired 1 MHz -- 72.1 -- dB Interferer CW at Desired 2 MHz -- 77.5 -- dB Interferer CW at Desired 10 MHz -- 90.4 -- dB Alternate channel selectivity, C/I2 Interferer is CW at 2 x channel-spacing Image rejection, Interferer is CW at image frequency Blocking selectivity, 0.1% BER. Desired is 2.4 kbps GFSK signal1 at 3 dB above sensitivity level C/IIMAGE C/IBLOCKER silabs.com | Building a more connected world. Rev. 1.6 | 64 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Min Typ Max Unit Upper limit of input power RSSIMAX range over which RSSI resolution is maintained -- -- 5 dBm Lower limit of input power RSSIMIN range over which RSSI resolution is maintained -98 -- -- dBm Over RSSIMIN to RSSIMAX range -- 0.25 -- dBm 30 MHz to 1 GHz -- -63 -57 dBm 1 GHz to 12 GHz -- -53 -47 dBm RSSI resolution Symbol RSSIRES Max spurious emissions dur- SPURRX ing active receive mode Test Condition Note: 1. Definition of reference signal is 2.4 kbps 2GFSK, BT=0.5, f = 1.2 kHz, RX channel BW = 4.797 kHz, channel spacing = 12.5 kHz. 2. Definition of reference signal is 38.4 kbps 2GFSK, BT=0.5, f = 20 kHz, RX channel BW = 74.809 kHz, channel spacing = 100 kHz. 3. Definition of reference signal is 500 kbps 2GFSK, BT=0.5, f = 125 kHz, RX channel BW = 753.320 kHz. 4. Definition of reference signal is 20 kbps BPSK 5. RFSENSE performance is only valid from 0 to 85 C. RFSENSE should be disabled outside this temperature range. silabs.com | Building a more connected world. Rev. 1.6 | 65 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.10.5 Sub-GHz RF Transmitter characteristics for 490 MHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = External PA Supply. RFVDD and external PA supply paths filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 490 MHz. Table 4.24. Sub-GHz RF Transmitter characteristics for 490 MHz Band Parameter Symbol Min Typ Max Unit RF tuning frequency range FRANGE 470 -- 510 MHz Maximum TX Power1 POUTMAX 18.1 20.3 23.7 dBm Minimum active TX Power POUTMIN -44.9 -- dBm Output power step size POUTSTEP output power > 0 dBm -- 0.5 -- dB Output power variation vs supply, peak to peak POUTVAR_V at 20 dBm;1.8 V < VVREGVDD < 3.3 V, External PA supply connected directly to external supply, T = 25 C -- 4.3 -- dB Output power variation vs temperature, peak to peak POUTVAR_T -40 to +85 C at 20 dBm -- 0.2 0.9 dB Output power variation vs RF POUTVAR_F frequency T = 25 C -- 0.2 0.4 dB Harmonic emissions, 20 dBm output power setting, 490 MHz Per China SRW Requirement, Section 2.1, frequencies below 1GHz -- -40 -36 dBm Per China SRW Requirement, Section 2.1, frequencies above 1GHz -- -36 -30 dBm Per China SRW Requirement, Section 3 (48.5-72.5MHz, 76-108MHz, 167-223MHz, 470-556MHz, and 606-798MHz) -- -54 -- dBm Per China SRW Requirement, Section 2.1 (other frequencies below 1GHz) -- -42 -- dBm Per China SRW Requirement, Section 2.1 (frequencies above 1GHz) -- -36 -- dBm SPURHARM_CN Spurious emissions, 20 dBm SPUROOB_CN output power setting, 490 MHz Test Condition External PA supply = 3.3V Note: 1. Supported transmit power levels are determined by the ordering part number (OPN). Transmit power ratings for all devices covered in this datasheet can be found in the Max TX Power column of the Ordering Information Table. silabs.com | Building a more connected world. Rev. 1.6 | 66 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.10.6 Sub-GHz RF Receiver Characteristics for 490 MHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = External PA Supply. RFVDD and external PA supply paths filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 490 MHz. Table 4.25. Sub-GHz RF Receiver Characteristics for 490 MHz Band Parameter Symbol Tuning frequency range FRANGE Test Condition Min Typ Max Unit 470 -- 510 MHz Max usable input level, 0.1% SAT2k4 BER Desired is reference 2.4 kbps GFSK signal1 -- 10 -- dBm Max usable input level, 0.1% SAT38k4 BER Desired is reference 38.4 kbps GFSK signal2 -- 10 -- dBm Sensitivity Desired is reference 2.4 kbps GFSK signal1, 0.1% BER -- -122.2 -- dBm Desired is reference 38.4 kbps GFSK signal2, 0.1% BER, T 85 C -- -111.4 -108.9 dBm Desired is reference 10 kbps GFSK signal3, 0.1% BER, T 85 C -- -116.8 -113.9 dBm Desired is reference 100 kbps GFSK signal4, 0.1% BER, T 85 C -- -107.3 -104.7 dBm Desired is reference 100 kbps GFSK signal4, 0.1% BER -- -28.1 -- dBm SENS Level above which RFSENSE will trigger5 RFSENSETRIG Level below which RFSENSE will not trigger5 RFSENSETHRES CW at 490 MHz -- -50 -- dBm Adjacent channel selectivity, Interferer is CW at 1 x channel-spacing C/I1 Desired is 2.4 kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER 48 60.3 -- dB Desired is 38.4kbps GFSK signal2 at 3dB above sensitivity level, 0.1% BER 38.3 45.6 -- dB Desired is 2.4kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 60.4 -- dB Desired is 38.4kbps GFSK signal2 at 3dB above sensitivity level, 0.1% BER -- 52.6 -- dB Desired is 2.4kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 56.5 -- dB Desired is 38.4kbps GFSK signal2 at 3dB above sensitivity level, 0.1% BER -- 54.1 -- dB Interferer CW at Desired 1 MHz -- 73.9 -- dB Interferer CW at Desired 2 MHz -- 75.4 -- dB Interferer CW at Desired 10 MHz -- 90.2 -- dB Alternate channel selectivity, C/I2 Interferer is CW at 2 x channel-spacing Image rejection, Interferer is CW at image frequency Blocking selectivity, 0.1% BER. Desired is 2.4 kbps GFSK signal1 at 3 dB above sensitivity level C/IIMAGE C/IBLOCKER silabs.com | Building a more connected world. Rev. 1.6 | 67 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Min Typ Max Unit Upper limit of input power RSSIMAX range over which RSSI resolution is maintained -- -- 5 dBm Lower limit of input power RSSIMIN range over which RSSI resolution is maintained -98 -- -- dBm Over RSSIMIN to RSSIMAX range -- 0.25 -- dBm 30 MHz to 1 GHz -- -53 -47 dBm 1 GHz to 12 GHz -- -53 -47 dBm RSSI resolution Symbol RSSIRES Max spurious emissions dur- SPURRX ing active receive mode Test Condition Note: 1. Definition of reference signal is 2.4 kbps 2GFSK, BT=0.5, f = 1.2 kHz, RX channel BW = 4.798 kHz, channel spacing = 12.5 kHz. 2. Definition of reference signal is 38.4 kbps 2GFSK, BT=0.5, f = 20 kHz, RX channel BW = 74.809 kHz, channel spacing = 100 kHz. 3. Definition of reference signal is 10 kbps 2GFSK, BT=0.5, f = 5 kHz, RX channel BW = 20.038 kHz. 4. Definition of reference signal is 100 kbps 2GFSK, BT=0.5, f = 50 kHz, RX channel BW = 198.024 kHz. 5. RFSENSE performance is only valid from 0 to 85 C. RFSENSE should be disabled outside this temperature range. silabs.com | Building a more connected world. Rev. 1.6 | 68 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.10.7 Sub-GHz RF Transmitter characteristics for 433 MHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = External PA Supply. RFVDD and external PA supply paths filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 433 MHz. Table 4.26. Sub-GHz RF Transmitter characteristics for 433 MHz Band Parameter Symbol RF tuning frequency range FRANGE Maximum TX Power1 POUTMAX Min Typ Max Unit 426 -- 445 MHz External PA supply connected to DC-DC output, 14dBm output power 12.5 15.1 17.4 dBm External PA supply connected to DC-DC output, 10dBm output power 8.3 10.6 13.3 dBm -- -42 -- dBm output power > 0 dBm -- 0.5 -- dB Output power variation vs POUTVAR_V supply, peak to peak, Pout = 10dBm At 10 dBm;1.8 V < VVREGVDD < 3.3 V, External PA supply = DCDC output, T = 25 C -- 1.7 -- dB Output power variation vs temperature, peak to peak, Pout= 10dBm -40 to +85C at 10dBm -- 0.5 1.2 dB T = 25 C -- 0.1 0.2 dB Minimum active TX Power POUTMIN Output power step size POUTSTEP POUTVAR_T Output power variation vs RF POUTVAR_F frequency, Pout = 10dBm Test Condition Spurious emissions of harmonics FCC, Conducted measurement, 14dBm match, External PA supply connected to DC-DC output, Test Frequency = 434 MHz SPURHARM_FCC In restricted bands, per FCC Part 15.205 / 15.209 -- -47 -42 dBm In non-restricted bands, per FCC Part 15.231 -- -26 -20 dBc Spurious emissions out-ofband FCC, Conducted measurement, 14dBm match, External PA supply connected to DC-DC output, Test Frequency = 434 MHz SPUROOB_FCC In non-restricted bands, per FCC Part 15.231 -- -26 -20 dBc In restricted bands (30-88 MHz), per FCC Part 15.205 / 15.209 -- -52 -46 dBm In restricted bands (88-216 MHz), per FCC Part 15.205 / 15.209 -- -61 -56 dBm In restricted bands (216-960 MHz), per FCC Part 15.205 / 15.209 -- -58 -52 dBm In restricted bands (>960 MHz), per FCC Part 15.205 / 15.209 -- -47 -42 dBm SPURHARM_ETSI Per ETSI EN 300-220, Section 7.8.2.1 (frequencies below 1Ghz) -- -42 -36 dBm Per ETSI EN 300-220, Section 7.8.2.1 (frequencies above 1Ghz) -- -36 -30 dBm Spurious emissions of harmonics ETSI, Conducted measurement, 14dBm match, External PA supply connected to DC-DC output, Test Frequency = 434 MHz silabs.com | Building a more connected world. Rev. 1.6 | 69 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Spurious emissions out-ofband ETSI, Conducted measurement, 14dBm match, External PA supply connected to DC-DC output, Test Frequency = 434 MHz SPUROOB_ETSI Per ETSI EN 300-220, Section 7.8.2.1 (47-74 MHz, 87.5-118 MHz, 174-230 MHz, and 470-862 MHz) -- -60 -54 dBm Per ETSI EN 300-220, Section 7.8.2.1 (other frequencies below 1 GHz) -- -42 -36 dBm Per ETSI EN 300-220, Section 7.8.2.1 (frequencies above 1 GHz) -- -36 -30 dBm Note: 1. Supported transmit power levels are determined by the ordering part number (OPN). Transmit power ratings for all devices covered in this datasheet can be found in the Max TX Power column of the Ordering Information Table. silabs.com | Building a more connected world. Rev. 1.6 | 70 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.10.8 Sub-GHz RF Receiver Characteristics for 433 MHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = External PA Supply. RFVDD and external PA supply paths filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 433 MHz. Table 4.27. Sub-GHz RF Receiver Characteristics for 433 MHz Band Parameter Symbol Tuning frequency range FRANGE Test Condition Min Typ Max Unit 426 -- 445 MHz Max usable input level, 0.1% SAT2k4 BER Desired is reference 2.4 kbps GFSK signal1 -- 10 -- dBm Max usable input level, 0.1% SAT50k BER Desired is reference 50 kbps GFSK signal2 -- 10 -- dBm Sensitivity Desired is reference 4.8 kbps OOK signal3, 20% PER -- -107.4 -- dBm Desired is reference 100 kbps GFSK signal4, 0.1% BER, T 85 C -- -107.3 -105 dBm Desired is reference 50 kbps GFSK signal2, 0.1% BER, T 85 C -- -110.3 -107.2 dBm Desired is reference 2.4 kbps GFSK signal1, 0.1% BER -- -123.1 -- dBm Desired is reference 9.6 kbps GFSK signal5, 1% PER, T 85 C -- -112.6 -109 dBm SENS Level above which RFSENSE will trigger6 RFSENSETRIG CW at 433 MHz -- -28.1 -- dBm Level below which RFSENSE will not trigger6 RFSENSETHRES CW at 433 MHz -- -50 -- dBm Adjacent channel selectivity, Interferer is CW at 1 x channel-spacing C/I1 Desired is 4.8 kbps OOK signal3 at 3dB above sensitivity level, 20% PER -- 51.6 -- dB Desired is 100 kbps GFSK signal4 at 3dB above sensitivity level, 0.1% BER 35 44.1 -- dB Desired is 2.4 kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER 47 61.5 -- dB Desired is 50 kbps GFSK signal2 at 3dB above sensitivity level, 0.1% BER 45.6 53.1 -- dB -- 35.7 -- dB Desired is 9.6 kbps 4GFSK signal5 at 3dB above sensitivity level, 1% PER silabs.com | Building a more connected world. Rev. 1.6 | 71 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Min Typ Max Unit Desired is 4.8 kbps OOK signal3 at 3dB above sensitivity level, 20% PER -- 57.8 -- dB Desired is 100 kbps GFSK signal4 at 3dB above sensitivity level, 0.1% BER -- 54.6 -- dB Desired is 2.4 kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 62.4 -- dB Desired is 50 kbps GFSK signal2 at 3dB above sensitivity level, 0.1% BER -- 58.1 -- dB Desired is 9.6 kbps 4GFSK signal5 at 3dB above sensitivity level, 1% PER -- 50.6 -- dB Desired is 4.8 kbps OOK signal3 at 3dB above sensitivity level, 20% PER -- 46.5 -- dB Desired is 100 kbps GFSK signal4 at 3dB above sensitivity level, 0.1% BER -- 51.7 -- dB Desired is 2.4 kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 57.5 -- dB Desired is 50 kbps GFSK signal2 at 3dB above sensitivity level, 0.1% BER -- 54.4 -- dB Desired is 9.6 kbps 4GFSK signal5 at 3dB above sensitivity level, 1% PER -- 48 -- dB Interferer CW at Desired 1 MHz -- 75.7 -- dB Interferer CW at Desired 2 MHz -- 77.2 -- dB Interferer CW at Desired 10 MHz -- 92 -- dB Desired is 2.4 kbps GFSK signal1 at 3dB above sensitivity level -- 58.8 -- dB Upper limit of input power RSSIMAX range over which RSSI resolution is maintained -- -- 5 dBm Lower limit of input power RSSIMIN range over which RSSI resolution is maintained -98 -- -- dBm Over RSSIMIN to RSSIMAX range -- 0.25 -- dBm 216-960 MHz -- -55 -49 dBm Above 960 MHz -- -47 -41 dBm Alternate channel selectivity, C/I2 Interferer is CW at 2 x channel-spacing Image rejection, Interferer is CW at image frequency C/IIMAGE Blocking selectivity, 0.1% BER. Desired is 2.4 kbps GFSK signal1 at 3dB above sensitivity level C/IBLOCKER Intermod selectivity, 0.1% BER. CW interferers at 12.5 kHz and 25 kHz offsets C/IIM RSSI resolution RSSIRES Max spurious emissions dur- SPURRX_FCC ing active receive mode, per FCC Part 15.109(a) silabs.com | Building a more connected world. Test Condition Rev. 1.6 | 72 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Max spurious emissions dur- SPURRX_ETSI ing active receive mode, per ETSI 300-220 Section 8.6 Below 1000 MHz -- -63 -57 dBm Above 1000 MHz -- -53 -47 dBm Max spurious emissions dur- SPURRX_ARIB ing active receive mode, per ARIB STD T67 Section 3.3(5) Below 710 MHz, RBW=100kHz -- -60 -54 dBm Note: 1. Definition of reference signal is 2.4 kbps 2GFSK, BT=0.5, f = 1.2 kHz, RX channel BW = 4.798 kHz, channel spacing = 12.5 kHz. 2. Definition of reference signal is 50 kbps 2GFSK, BT=0.5, f = 25 kHz, RX channel BW = 99.012 kHz, channel spacing = 200 kHz. 3. Definition of reference signal is 4.8 kbps OOK, RX channel BW = 306.036 kHz, channel spacing = 500 kHz. 4. Definition of reference signal is 100 kbps 2GFSK, BT=0.5, f = 50 kHz, RX channel BW = 198.024 kHz, channel spacing = 200 kHz. 5. Definition of reference signal is 9.6 kbps 4GFSK, BT=0.5, inner deviation = 0.8 kHz, RX channel BW = 8.5 kHz, channel spacing = 12.5 kHz. 6. RFSENSE performance is only valid from 0 to 85 C. RFSENSE should be disabled outside this temperature range. silabs.com | Building a more connected world. Rev. 1.6 | 73 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.10.9 Sub-GHz RF Transmitter characteristics for 315 MHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = External PA Supply. RFVDD and external PA supply paths filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 315 MHz. Table 4.28. Sub-GHz RF Transmitter characteristics for 315 MHz Band Parameter Symbol Min Typ Max Unit RF tuning frequency range FRANGE 195 -- 358 MHz Maximum TX Power1 POUTMAX 13.8 17.2 21.1 dBm Minimum active TX Power POUTMIN -43.9 -- dBm Output power step size POUTSTEP output power > 0 dBm -- 0.5 -- dB Output power variation vs supply POUTVAR_V 1.8 V < VVREGVDD < 3.3 V, External PA supply = DC-DC output, T = 25 C -- 1.8 -- dB Output power variation vs temperature POUTVAR_T -40 to +85C -- 0.5 1.2 dB T = 25 C -- 0.1 0.7 dB SPURHARM_FCC In restricted bands, per FCC Part 15.205 / 15.209 -- -47 -42 dBm In non-restricted bands, per FCC Part 15.231 -- -26 -20 dBc In non-restricted bands, per FCC Part 15.231 -- -26 -20 dBc In restricted bands (30-88 MHz), per FCC Part 15.205 / 15.209 -- -52 -46 dBm In restricted bands (88-216 MHz), per FCC Part 15.205 / 15.209 -- -61 -56 dBm In restricted bands (216-960 MHz), per FCC Part 15.205 / 15.209 -- -58 -52 dBm In restricted bands (>960 MHz), per FCC Part 15.205 / 15.209 -- -47 -42 dBm Output power variation vs RF POUTVAR_F frequency Spurious emissions of harmonics at 14 dBm output power, Conducted measurement, 14dBm match, External PA supply connected to DC-DC output, Test Frequency = 303 MHz Spurious emissions out-ofSPUROOB_FCC band at 14 dBm output power, Conducted measurement, 14dBm match, External PA supply connected to DC-DC output, Test Frequency = 303 MHz Test Condition External PA supply connected to DC-DC output, T 85 C Note: 1. Supported transmit power levels are determined by the ordering part number (OPN). Transmit power ratings for all devices covered in this datasheet can be found in the Max TX Power column of the Ordering Information Table. silabs.com | Building a more connected world. Rev. 1.6 | 74 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.10.10 Sub-GHz RF Receiver Characteristics for 315 MHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = External PA Supply. RFVDD and external PA supply paths filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 315 MHz. Table 4.29. Sub-GHz RF Receiver Characteristics for 315 MHz Band Parameter Symbol Tuning frequency range FRANGE Test Condition Min Typ Max Unit 195 -- 358 MHz Max usable input level, 0.1% SAT2k4 BER Desired is reference 2.4 kbps GFSK signal1 -- 10 -- dBm Max usable input level, 0.1% SAT38k4 BER Desired is reference 38.4 kbps GFSK signal2 -- 10 -- dBm Sensitivity Desired is reference 2.4 kbps GFSK signal1, 0.1% BER, T 85 C -- -123.2 -120.7 dBm Desired is reference 38.4 kbps GFSK signal2, 0.1% BER, T 85 C -- -111.4 -108.6 dBm Desired is reference 500 kbps GFSK signal3, 0.1% BER, T 85 C -- -98.8 -95.5 dBm SENS Level above which RFSENSE will trigger4 RFSENSETRIG CW at 315 MHz -- -28.1 -- dBm Level below which RFSENSE will not trigger4 RFSENSETHRES CW at 315 MHz -- -50 -- dBm Adjacent channel selectivity, Interferer is CW at 1 x channel-spacing C/I1 Desired is 2.4 kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER 54.1 63.6 -- dB Desired is 38.4kbps GFSK signal2 at 3dB above sensitivity level, 0.1% BER -- 49.9 -- dB Desired is 2.4kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 64.2 -- dB Desired is 38.4kbps GFSK signal2 at 3dB above sensitivity level2, 0.1% BER -- 56.2 -- dB Desired is 2.4kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 53 -- dB Desired is 38.4kbps GFSK signal2 at 3dB above sensitivity level, 0.1% BER -- 51.4 -- dB Interferer CW at Desired 1 MHz -- 75 -- dB Interferer CW at Desired 2 MHz -- 76.5 -- dB 72.6 91.9 -- dB Alternate channel selectivity, C/I2 Interferer is CW at 2 x channel-spacing Image rejection, Interferer is CW at image frequency Blocking selectivity, 0.1% BER. Desired is 2.4 kbps GFSK signal1 at 3 dB above sensitivity level C/IIMAGE C/IBLOCKER silabs.com | Building a more connected world. Interferer CW at Desired 10 MHz Rev. 1.6 | 75 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Min Typ Max Unit Upper limit of input power RSSIMAX range over which RSSI resolution is maintained -- -- 5 dBm Lower limit of input power RSSIMIN range over which RSSI resolution is maintained -98 -- -- dBm Over RSSIMIN to RSSIMAX range -- 0.25 -- dBm 216-960 MHz -- -63 -57 dBm Above 960MHz -- -53 -47 dBm RSSI resolution Symbol RSSIRES Max spurious emissions dur- SPURRX_FCC ing active receive mode, per FCC Part 15.109(a) Test Condition Note: 1. Definition of reference signal is 2.4 kbps 2GFSK, BT=0.5, f = 1.2 kHz, RX channel BW = 4.798 kHz, channel spacing = 12.5 kHz. 2. Definition of reference signal is 38.4 kbps 2GFSK, BT=0.5, f = 20 kHz, RX channel BW = 74.809 kHz, channel spacing = 100 kHz. 3. Definition of reference signal is 500 kbps 2GFSK, BT=0.5, f = 125 kHz, RX channel BW = 753.320 kHz. 4. RFSENSE performance is only valid from 0 to 85 C. RFSENSE should be disabled outside this temperature range. silabs.com | Building a more connected world. Rev. 1.6 | 76 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.10.11 Sub-GHz RF Transmitter Characteristics for 169 MHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = External PA Supply. RFVDD and external PA supply paths filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 169 MHz. Table 4.30. Sub-GHz RF Transmitter Characteristics for 169 MHz Band Parameter Symbol RF tuning frequency range FRANGE Maximum TX Power1 POUTMAX Minimum active TX Power POUTMIN Output power step size POUTSTEP output power > 0 dBm Output power variation vs supply, peak to peak POUTVAR_V Output power variation vs temperature, peak to peak POUTVAR_T Spurious emissions of harSPURHARM_ETSI monics, Conducted measurement, External PA supply = 3.3 V, Test Frequency = 169 MHz Spurious emissions out-ofSPUROOB_ETSI band, Conducted measurement, External PA supply = 3.3 V, Test Frequency = 169 MHz Test Condition Min Typ Max Unit 169 -- 170 MHz 18.1 19.7 22.4 dBm -42.6 -- dBm -- 0.5 -- dB 1.8 V < VVREGVDD < 3.3 V, External PA supply = 3.3 V, T = 25 C -- 4.8 5.0 dB -40 to +85 C at 20 dBm -- 0.6 1.2 dB Per ETSI EN 300-220, Section 7.8.2.1 (47-74 MHz, 87.5-118 MHz, 174-230 MHz, and 470-862 MHz) -- -42 -- dBm Per ETSI EN 300-220, Section 7.8.2.1 (other frequencies below 1 GHz)2 -- -38 -- dBm Per ETSI EN 300-220, Section 7.8.2.1 (frequencies above 1 GHz)2 -- -36 -- dBm Per ETSI EN 300-220, Section 7.8.2.1 (47-74 MHz, 87.5-118 MHz, 174-230 MHz, and 470-862 MHz) -- -42 -36 dBm Per ETSI EN 300-220, Section 7.8.2.1 (other frequencies below 1 GHz) -- -42 -36 dBm Per ETSI EN 300-220, Section 7.8.2.1 (frequencies above 1 GHz) -- -36 -30 dBm External PA supply = 3.3 V Note: 1. Supported transmit power levels are determined by the ordering part number (OPN). Transmit power ratings for all devices covered in this datasheet can be found in the Max TX Power column of the Ordering Information Table. 2. Typical value marginally passes specification. Additional margin can be obtained by increasing the order of the harmonic filter. silabs.com | Building a more connected world. Rev. 1.6 | 77 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.10.12 Sub-GHz RF Receiver Characteristics for 169 MHz Band Unless otherwise indicated, typical conditions are: T = 25 C, VREGVDD = AVDD = IOVDD = 3.3 V, DVDD = RFVDD = External PA Supply. RFVDD and external PA supply paths filtered using ferrites. Crystal frequency = 38.4 MHz. RF center frequency 169 MHz. Table 4.31. Sub-GHz RF Receiver Characteristics for 169 MHz Band Parameter Symbol Tuning frequency range FRANGE Test Condition Min Typ Max Unit 169 -- 170 MHz Max usable input level, 0.1% SAT2k4 BER Desired is reference 2.4 kbps GFSK signal1 -- 10 -- dBm Max usable input level, 0.1% SAT38k4 BER Desired is reference 38.4 kbps GFSK signal2 -- 10 -- dBm Sensitivity Desired is reference 2.4 kbps GFSK signal1, 0.1% BER -- -124 -- dBm Desired is reference 38.4 kbps GFSK signal2, 0.1% BER, T 85 C -- -112.2 -108 dBm Desired is reference 500 kbps GFSK signal3, 0.1% BER, T 85 C -- -99.2 -96 dBm SENS Level above which RFSENSE will trigger4 RFSENSETRIG CW at 169 MHz -- -28.1 -- dBm Level below which RFSENSE will not trigger4 RFSENSETHRES CW at 169 MHz -- -50 -- dBm Adjacent channel selectivity, Interferer is CW at 1 x channel-spacing C/I1 Desired is 2.4 kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 64.8 -- dB Desired is 38.4kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER 43.3 51.4 -- dB Desired is 2.4kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 67.4 -- dB Desired is 38.4kbps GFSK signal2 at 3dB above sensitivity level, 0.1% BER -- 60.6 -- dB Desired is 2.4kbps GFSK signal1 at 3dB above sensitivity level, 0.1% BER -- 47.1 -- dB Desired is 38.4kbps GFSK signal2 at 3dB above sensitivity level, 0.1% BER -- 47.1 -- dB Interferer CW at Desired 1 MHz -- 73.4 -- dB Interferer CW at Desired 2 MHz -- 75 -- dB Interferer CW at Desired 10 MHz 80 90.1 -- dB -- -- 5 dBm Alternate channel selectivity, C/I2 Interferer is CW at 2 x channel-spacing Image rejection, Interferer is CW at image frequency Blocking selectivity, 0.1% BER. Desired is 2.4 kbps GFSK signal1 at 3 dB above sensitivity level C/IIMAGE C/IBLOCKER Upper limit of input power RSSIMAX range over which RSSI resolution is maintained silabs.com | Building a more connected world. Rev. 1.6 | 78 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit -98 -- -- dBm Over RSSIMIN to RSSIMAX range -- 0.25 -- dBm 30 MHz to 1 GHz -- -63 -57 dBm 1 GHz to 12 GHz -- -53 -47 dBm Lower limit of input power RSSIMIN range over which RSSI resolution is maintained RSSI resolution RSSIRES Max spurious emissions dur- SPURRX ing active receive mode Note: 1. Definition of reference signal is 2.4 kbps 2GFSK, BT=0.5, f = 1.2 kHz, RX channel BW = 4.798 kHz, channel spacing = 12.5 kHz. 2. Definition of reference signal is 38.4 kbps 2GFSK, BT=0.5, f = 20 kHz, RX channel BW = 74.809 kHz, channel spacing = 100 kHz. 3. Definition of reference signal is 500 kbps 2GFSK, BT=0.5, f = 125 kHz, RX channel BW = 753.320 kHz. 4. RFSENSE performance is only valid from 0 to 85 C. RFSENSE should be disabled outside this temperature range. 4.1.11 Modem Table 4.32. Modem Parameter Symbol Test Condition Min Typ Max Unit Receive bandwidth BWRX Configurable range with 38.4 MHz crystal 0.1 -- 2530 kHz IF frequency fIF Configurable range with 38.4 MHz crystal. Selected steps available. 150 -- 1371 kHz DSSS symbol length SLDSSS Configurable in steps of 1 chip 2 -- 32 chips DSSS bits per symbol BPSDSSS Configurable 1 -- 4 bits/ symbol silabs.com | Building a more connected world. Rev. 1.6 | 79 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.12 Oscillators 4.1.12.1 Low-Frequency Crystal Oscillator (LFXO) Table 4.33. Low-Frequency Crystal Oscillator (LFXO) Parameter Symbol Crystal frequency Test Condition Min Typ Max Unit fLFXO -- 32.768 -- kHz Supported crystal equivalent series resistance (ESR) ESRLFXO -- -- 70 k Supported range of crystal load capacitance 1 CLFXO_CL 6 -- 18 pF On-chip tuning cap range 2 CLFXO_T 8 -- 40 pF On-chip tuning cap step size SSLFXO -- 0.25 -- pF Current consumption after startup 3 ILFXO ESR = 70 kOhm, CL = 7 pF, GAIN4 = 2, AGC4 = 1 -- 273 -- nA Start- up time tLFXO ESR = 70 kOhm, CL = 7 pF, GAIN4 = 2 -- 308 -- ms On each of LFXTAL_N and LFXTAL_P pins Note: 1. Total load capacitance as seen by the crystal. 2. The effective load capacitance seen by the crystal will be CLFXO_T /2. This is because each XTAL pin has a tuning cap and the two caps will be seen in series by the crystal. 3. Block is supplied by AVDD if ANASW = 0, or DVDD if ANASW=1 in EMU_PWRCTRL register. 4. In CMU_LFXOCTRL register. silabs.com | Building a more connected world. Rev. 1.6 | 80 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.12.2 High-Frequency Crystal Oscillator (HFXO) Table 4.34. High-Frequency Crystal Oscillator (HFXO) Parameter Symbol Test Condition Min Typ Max Unit Crystal frequency fHFXO 38.4 MHz required for radio transciever operation 38 38.4 40 MHz Supported crystal equivalent series resistance (ESR) ESRHFXO_38M4 Crystal frequency 38.4 MHz -- -- 60 Supported range of crystal load capacitance 1 CHFXO_CL 6 -- 12 pF On-chip tuning cap range 2 CHFXO_T 9 20 25 pF On-chip tuning capacitance step SSHFXO -- 0.04 -- pF Startup time tHFXO 38.4 MHz, ESR = 50 Ohm, CL = 10 pF -- 300 -- s Frequency tolerance for the crystal FTHFXO 38.4 MHz, ESR = 50 Ohm, CL = 10 pF -40 -- 40 ppm On each of HFXTAL_N and HFXTAL_P pins Note: 1. Total load capacitance as seen by the crystal. 2. The effective load capacitance seen by the crystal will be CHFXO_T /2. This is because each XTAL pin has a tuning cap and the two caps will be seen in series by the crystal. 4.1.12.3 Low-Frequency RC Oscillator (LFRCO) Table 4.35. Low-Frequency RC Oscillator (LFRCO) Parameter Symbol Test Condition Min Typ Max Unit Oscillation frequency fLFRCO ENVREF1 = 1, T 85 C 31.3 32.768 33.6 kHz ENVREF1 = 1, T > 85 C 31.6 32.768 36.8 kHz ENVREF1 = 0, T 85 C 31.3 32.768 33.4 kHz ENVREF1 = 0, T > 85 C 30.0 32.768 33.4 kHz -- 500 -- s ENVREF = 1 in CMU_LFRCOCTRL -- 370 -- nA ENVREF = 0 in CMU_LFRCOCTRL -- 520 -- nA Startup time tLFRCO Current consumption 2 ILFRCO Note: 1. In CMU_LFRCOCTRL register. 2. Block is supplied by AVDD if ANASW = 0, or DVDD if ANASW=1 in EMU_PWRCTRL register. silabs.com | Building a more connected world. Rev. 1.6 | 81 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.12.4 High-Frequency RC Oscillator (HFRCO) Table 4.36. High-Frequency RC Oscillator (HFRCO) Parameter Symbol Test Condition Min Typ Max Unit Frequency accuracy fHFRCO_ACC At production calibrated frequencies, across supply voltage and temperature -2.5 -- 2.5 % Start-up time tHFRCO fHFRCO 19 MHz -- 300 -- ns 4 < fHFRCO < 19 MHz -- 1 -- s fHFRCO 4 MHz -- 2.5 -- s fHFRCO = 38 MHz -- 244 265 A fHFRCO = 32 MHz -- 204 222 A fHFRCO = 26 MHz -- 173 188 A fHFRCO = 19 MHz -- 143 156 A fHFRCO = 16 MHz -- 123 136 A fHFRCO = 13 MHz -- 110 124 A fHFRCO = 7 MHz -- 85 94 A fHFRCO = 4 MHz -- 32 37 A fHFRCO = 2 MHz -- 28 34 A fHFRCO = 1 MHz -- 26 31 A -- 0.8 -- % Current consumption on all supplies IHFRCO Coarse trim step size (% of period) SSHFRCO_COARS Fine trim step size (% of period) SSHFRCO_FINE -- 0.1 -- % Period jitter PJHFRCO -- 0.2 -- % RMS E silabs.com | Building a more connected world. Rev. 1.6 | 82 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.12.5 Auxiliary High-Frequency RC Oscillator (AUXHFRCO) Table 4.37. Auxiliary High-Frequency RC Oscillator (AUXHFRCO) Parameter Symbol Test Condition Frequency accuracy fAUXHFRCO_ACC Start-up time tAUXHFRCO Current consumption on all supplies IAUXHFRCO Coarse trim step size (% of period) CO_COARSE Fine trim step size (% of period) CO_FINE Period jitter PJAUXHFRCO Min Typ Max Unit At production calibrated frequencies, across supply voltage and temperature -3 -- 3 % fAUXHFRCO 19 MHz -- 400 -- ns 4 < fAUXHFRCO < 19 MHz -- 1.4 -- s fAUXHFRCO 4 MHz -- 2.5 -- s fAUXHFRCO = 38 MHz -- 193 213 A fAUXHFRCO = 32 MHz -- 157 175 A fAUXHFRCO = 26 MHz -- 135 151 A fAUXHFRCO = 19 MHz -- 108 122 A fAUXHFRCO = 16 MHz -- 100 113 A fAUXHFRCO = 13 MHz -- 77 88 A fAUXHFRCO = 7 MHz -- 53 63 A fAUXHFRCO = 4 MHz -- 29 36 A fAUXHFRCO = 2 MHz -- 28 34 A fAUXHFRCO = 1 MHz -- 27 31 A -- 0.8 -- % -- 0.1 -- % -- 0.2 -- % RMS Min Typ Max Unit 0.95 1 1.07 kHz SSAUXHFRSSAUXHFR- 4.1.12.6 Ultra-low Frequency RC Oscillator (ULFRCO) Table 4.38. Ultra-low Frequency RC Oscillator (ULFRCO) Parameter Symbol Oscillation frequency fULFRCO silabs.com | Building a more connected world. Test Condition Rev. 1.6 | 83 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.13 Flash Memory Characteristics1 Table 4.39. Flash Memory Characteristics1 Parameter Symbol Flash erase cycles before failure ECFLASH Flash data retention RETFLASH Word (32-bit) programming time tW_PROG Test Condition Min Typ Max Unit 10000 -- -- cycles T 85 C 10 -- -- years T 125 C 10 -- -- years Burst write, 128 words, average time per word 20 24.4 30 s Single word 60 68.4 80 s Page erase time2 tPERASE 20 26.4 35 ms Mass erase time3 tMERASE 20 26.5 35 ms Device erase time4 5 tDERASE T 85 C -- 82 100 ms T 125 C -- 82 110 ms Page Erase -- -- 1.6 mA Erase current6 IERASE Write current6 IWRITE -- -- 3.8 mA Supply voltage during flash erase and write VFLASH 1.62 -- 3.6 V Note: 1. Flash data retention information is published in the Quarterly Quality and Reliability Report. 2. From setting the ERASEPAGE bit in MSC_WRITECMD to 1 until the BUSY bit in MSC_STATUS is cleared to 0. Internal setup and hold times for flash control signals are included. 3. Mass erase is issued by the CPU and erases all flash. 4. Device erase is issued over the AAP interface and erases all flash, SRAM, the Lock Bit (LB) page, and the User data page Lock Word (ULW). 5. From setting the DEVICEERASE bit in AAP_CMD to 1 until the ERASEBUSY bit in AAP_STATUS is cleared to 0. Internal setup and hold times for flash control signals are included. 6. Measured at 25 C. silabs.com | Building a more connected world. Rev. 1.6 | 84 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.14 General-Purpose I/O (GPIO) Table 4.40. General-Purpose I/O (GPIO) Parameter Symbol Test Condition Min Typ Max Unit Input low voltage1 VIL GPIO pins -- -- IOVDD*0.3 V Input high voltage1 VIH GPIO pins IOVDD*0.7 -- -- V Output high voltage relative to IOVDD VOH Sourcing 3 mA, IOVDD 3 V, IOVDD*0.8 -- -- V IOVDD*0.6 -- -- V IOVDD*0.8 -- -- V IOVDD*0.6 -- -- V -- -- IOVDD*0.2 V -- -- IOVDD*0.4 V -- -- IOVDD*0.2 V -- -- IOVDD*0.4 V All GPIO except LFXO pins, GPIO IOVDD, T 85 C -- 0.1 30 nA LFXO Pins, GPIO IOVDD, T 85 C -- 0.1 50 nA All GPIO except LFXO pins, GPIO IOVDD, T > 85 C -- -- 110 nA LFXO Pins, GPIO IOVDD, T > 85 C -- -- 250 nA IOVDD < GPIO IOVDD + 2 V -- 3.3 15 A 30 40 65 k 15 25 45 ns DRIVESTRENGTH2 = WEAK Sourcing 1.2 mA, IOVDD 1.62 V, DRIVESTRENGTH2 = WEAK Sourcing 20 mA, IOVDD 3 V, DRIVESTRENGTH2 = STRONG Sourcing 8 mA, IOVDD 1.62 V, DRIVESTRENGTH2 = STRONG Output low voltage relative to VOL IOVDD Sinking 3 mA, IOVDD 3 V, DRIVESTRENGTH2 = WEAK Sinking 1.2 mA, IOVDD 1.62 V, DRIVESTRENGTH2 = WEAK Sinking 20 mA, IOVDD 3 V, DRIVESTRENGTH2 = STRONG Sinking 8 mA, IOVDD 1.62 V, DRIVESTRENGTH2 = STRONG Input leakage current IIOLEAK Input leakage current on 5VTOL pads above IOVDD I5VTOLLEAK I/O pin pull-up/pull-down resistor3 RPUD Pulse width of pulses retIOGLITCH moved by the glitch suppression filter silabs.com | Building a more connected world. Rev. 1.6 | 85 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Output fall time, From 70% to 30% of VIO tIOOF CL = 50 pF, Min Typ Max Unit -- 1.8 -- ns -- 4.5 -- ns -- 2.2 -- ns -- 7.4 -- ns DRIVESTRENGTH2 = STRONG, SLEWRATE2 = 0x6 CL = 50 pF, DRIVESTRENGTH2 = WEAK, SLEWRATE2 = 0x6 Output rise time, From 30% to 70% of VIO tIOOR CL = 50 pF, DRIVESTRENGTH2 = STRONG, SLEWRATE = 0x62 CL = 50 pF, DRIVESTRENGTH2 = WEAK, SLEWRATE2 = 0x6 Note: 1. GPIO input threshold are proportional to the IOVDD supply, except for RESETn which is proportional to AVDD. 2. In GPIO_Pn_CTRL register. 3. GPIO pull-ups are referenced to the IOVDD supply, except for RESETn, which connects to AVDD. silabs.com | Building a more connected world. Rev. 1.6 | 86 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.15 Voltage Monitor (VMON) Table 4.41. Voltage Monitor (VMON) Parameter Symbol Test Condition Supply current (including I_SENSE) IVMON Loading of monitored supply ISENSE Threshold range VVMON_RANGE Threshold step size NVMON_STESP Response time tVMON_RES Hysteresis VVMON_HYST silabs.com | Building a more connected world. Min Typ Max Unit In EM0 or EM1, 1 active channel, T 85 C -- 6.3 10 A In EM0 or EM1, 1 active channel, T > 85 C -- -- 14 A In EM0 or EM1, All channels active, T 85 C -- 12.5 17 A In EM0 or EM1, All channels active, T > 85 C -- -- 21 A In EM2, EM3 or EM4, 1 channel active and above threshold -- 62 -- nA In EM2, EM3 or EM4, 1 channel active and below threshold -- 62 -- nA In EM2, EM3 or EM4, All channels active and above threshold -- 99 -- nA In EM2, EM3 or EM4, All channels active and below threshold -- 99 -- nA In EM0 or EM1 -- 2 -- A In EM2, EM3 or EM4 -- 2 -- nA 1.62 -- 3.4 V Coarse -- 200 -- mV Fine -- 20 -- mV Supply drops at 1V/s rate -- 460 -- ns -- 26 -- mV Rev. 1.6 | 87 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.16 Analog to Digital Converter (ADC) Specified at 1 Msps, ADCCLK = 16 MHz, BIASPROG = 0, GPBIASACC = 0, unless otherwise indicated. Table 4.42. Analog to Digital Converter (ADC) Parameter Symbol Resolution VRESOLUTION Input voltage range1 VADCIN Test Condition Single ended Differential Input range of external refer- VADCREFIN_P ence voltage, single ended and differential Min Typ Max Unit 6 -- 12 Bits -- -- VFS V -VFS/2 -- VFS/2 V 1 -- VAVDD V Power supply rejection2 PSRRADC At DC -- 80 -- dB Analog input common mode rejection ratio CMRRADC At DC -- 80 -- dB 1 Msps / 16 MHz ADCCLK, BIASPROG = 0, GPBIASACC = 1 4 -- 270 315 A 250 ksps / 4 MHz ADCCLK, BIASPROG = 6, GPBIASACC = 1 4 -- 125 -- A 62.5 ksps / 1 MHz ADCCLK, BIASPROG = 15, GPBIASACC = 1 4 -- 80 -- A Current from all supplies, us- IADC_NORMAL_LP 35 ksps / 16 MHz ADCCLK, BIAing internal reference buffer. SPROG = 0, GPBIASACC = 1 4 Duty-cycled operation. WAR5 ksps / 16 MHz ADCCLK BIAMUPMODE3 = NORMAL SPROG = 0, GPBIASACC = 1 4 -- 45 -- A -- 8 -- A Current from all supplies, us- IADC_STANDing internal reference buffer. BY_LP Duty-cycled operation. AWARMUPMODE3 = KEEPINSTANDBY or KEEPINSLOWACC 125 ksps / 16 MHz ADCCLK, BIASPROG = 0, GPBIASACC = 1 4 -- 105 -- A 35 ksps / 16 MHz ADCCLK, BIASPROG = 0, GPBIASACC = 1 4 -- 70 -- A Current from all supplies, us- IADC_CONTINUing internal reference buffer. OUS_HP Continuous operation. WARMUPMODE3 = KEEPADCWARM 1 Msps / 16 MHz ADCCLK, BIASPROG = 0, GPBIASACC = 0 4 -- 325 -- A 250 ksps / 4 MHz ADCCLK, BIASPROG = 6, GPBIASACC = 0 4 -- 175 -- A 62.5 ksps / 1 MHz ADCCLK, BIASPROG = 15, GPBIASACC = 0 4 -- 125 -- A Current from all supplies, us- IADC_NORMAL_HP 35 ksps / 16 MHz ADCCLK, BIAing internal reference buffer. SPROG = 0, GPBIASACC = 0 4 Duty-cycled operation. WAR5 ksps / 16 MHz ADCCLK BIAMUPMODE3 = NORMAL SPROG = 0, GPBIASACC = 0 4 -- 85 -- A -- 16 -- A Current from all supplies, us- IADC_CONTINUing internal reference buffer. OUS_LP Continuous operation. WARMUPMODE3 = KEEPADCWARM Current from all supplies, us- IADC_STANDing internal reference buffer. BY_HP Duty-cycled operation. AWARMUPMODE3 = KEEPINSTANDBY or KEEPINSLOWACC 125 ksps / 16 MHz ADCCLK, BIASPROG = 0, GPBIASACC = 0 4 -- 160 -- A 35 ksps / 16 MHz ADCCLK, BIASPROG = 0, GPBIASACC = 0 4 -- 125 -- A Current from HFPERCLK HFPERCLK = 16 MHz -- 160 -- A IADC_CLK silabs.com | Building a more connected world. Rev. 1.6 | 88 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol ADC clock frequency Min Typ Max Unit fADCCLK -- -- 16 MHz Throughput rate fADCRATE -- -- 1 Msps Conversion time5 tADCCONV 6 bit -- 7 -- cycles 8 bit -- 9 -- cycles 12 bit -- 13 -- cycles WARMUPMODE3 = NORMAL -- -- 5 s WARMUPMODE3 = KEEPINSTANDBY -- -- 2 s WARMUPMODE3 = KEEPINSLOWACC -- -- 1 s Internal reference6, differential measurement 58 67 -- dB External reference7, differential measurement -- 68 -- dB Spurious-free dynamic range SFDRADC (SFDR) 1 MSamples/s, 10 kHz full-scale sine wave -- 75 -- dB Differential non-linearity (DNL) DNLADC 12 bit resolution, No missing codes -1 -- 2 LSB Integral non-linearity (INL), End point method INLADC 12 bit resolution -6 -- 6 LSB Offset error VADCOFFSETERR -3 0 3 LSB Gain error in ADC VADCGAIN Using internal reference -- -0.2 3.5 % Using external reference -- -1 -- % -- -1.84 -- mV/C Startup time of reference generator and ADC core SNDR at 1Msps and fIN = 10kHz Temperature sensor slope tADCSTART SNDRADC VTS_SLOPE Test Condition Note: 1. The absolute voltage allowed at any ADC input is dictated by the power rail supplied to on-chip circuitry, and may be lower than the effective full scale voltage. All ADC inputs are limited to the ADC supply (AVDD or DVDD depending on EMU_PWRCTRL_ANASW). Any ADC input routed through the APORT will further be limited by the IOVDD supply to the pin. 2. PSRR is referenced to AVDD when ANASW=0 and to DVDD when ANASW=1 in EMU_PWRCTRL. 3. In ADCn_CTRL register. 4. In ADCn_BIASPROG register. 5. Derived from ADCCLK. 6. Internal reference option used corresponds to selection 2V5 in the SINGLECTRL_REF or SCANCTRL_REF register field. The differential input range with this configuration is 1.25 V. Typical value is characterized using full-scale sine wave input. Minimum value is production-tested using sine wave input at 1.5 dB lower than full scale. 7. External reference is 1.25 V applied externally to ADCnEXTREFP, with the selection CONF in the SINGLECTRL_REF or SCANCTRL_REF register field and VREFP in the SINGLECTRLX_VREFSEL or SCANCTRLX_VREFSEL field. The differential input range with this configuration is 1.25 V. silabs.com | Building a more connected world. Rev. 1.6 | 89 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.17 Analog Comparator (ACMP) Table 4.43. Analog Comparator (ACMP) Parameter Symbol Test Condition Input voltage range VACMPIN Supply voltage VACMPVDD Active current not including voltage reference3 IACMP Current consumption of inter- IACMPREF nal voltage reference3 silabs.com | Building a more connected world. Min Typ Max Unit ACMPVDD = ACMPn_CTRL_PWRSEL 1 -- -- VACMPVDD V BIASPROG2 0x10 or FULLBIAS2 = 0 1.8 -- VVREGVDD_ V 0x10 < BIASPROG2 0x20 and FULLBIAS2 = 1 2.1 BIASPROG2 = 1, FULLBIAS2 = 0 -- 50 -- nA BIASPROG2 = 0x10, FULLBIAS2 =0 -- 306 -- nA BIASPROG2 = 0x02, FULLBIAS2 =1 -- 6.5 -- A BIASPROG2 = 0x20, FULLBIAS2 =1 -- 75 92 A VLP selected as input using 2.5 V Reference / 4 (0.625 V) -- 50 -- nA VLP selected as input using VDD -- 20 -- nA VBDIV selected as input using 1.25 V reference / 1 -- 4.1 -- A VADIV selected as input using VDD/1 -- 2.4 -- A MAX -- VVREGVDD_ V MAX Rev. 1.6 | 90 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Hysteresis (VCM = 1.25 V, BIASPROG2 = 0x10, FULLBIAS2 = 1) VACMPHYST Comparator delay5 tACMPDELAY Min Typ Max Unit HYSTSEL4 = HYST0 -3 0 3 mV HYSTSEL4 = HYST1 5 18 27 mV HYSTSEL4 = HYST2 12 33 50 mV HYSTSEL4 = HYST3 17 46 65 mV HYSTSEL4 = HYST4 23 57 82 mV HYSTSEL4 = HYST5 26 68 98 mV HYSTSEL4 = HYST6 30 79 130 mV HYSTSEL4 = HYST7 34 90 150 mV HYSTSEL4 = HYST8 -3 0 3 mV HYSTSEL4 = HYST9 -27 -18 -5 mV HYSTSEL4 = HYST10 -50 -33 -12 mV HYSTSEL4 = HYST11 -65 -45 -17 mV HYSTSEL4 = HYST12 -82 -57 -23 mV HYSTSEL4 = HYST13 -98 -67 -26 mV HYSTSEL4 = HYST14 -130 -78 -30 mV HYSTSEL4 = HYST15 -150 -88 -34 mV BIASPROG2 = 1, FULLBIAS2 = 0 -- 30 -- s BIASPROG2 = 0x10, FULLBIAS2 =0 -- 3.7 -- s BIASPROG2 = 0x02, FULLBIAS2 =1 -- 360 -- ns BIASPROG2 = 0x20, FULLBIAS2 =1 -- 35 -- ns -35 -- 35 mV Offset voltage VACMPOFFSET BIASPROG2 =0x10, FULLBIAS2 =1 Reference voltage VACMPREF Internal 1.25 V reference 1 1.25 1.47 V Internal 2.5 V reference 2 2.5 2.8 V CSRESSEL6 = 0 -- infinite -- k CSRESSEL6 = 1 -- 15 -- k CSRESSEL6 = 2 -- 27 -- k CSRESSEL6 = 3 -- 39 -- k CSRESSEL6 = 4 -- 51 -- k CSRESSEL6 = 5 -- 100 -- k CSRESSEL6 = 6 -- 162 -- k CSRESSEL6 = 7 -- 235 -- k Capacitive sense internal re- RCSRES sistance silabs.com | Building a more connected world. Rev. 1.6 | 91 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Note: 1. ACMPVDD is a supply chosen by the setting in ACMPn_CTRL_PWRSEL and may be IOVDD, AVDD or DVDD. 2. In ACMPn_CTRL register. 3. The total ACMP current is the sum of the contributions from the ACMP and its internal voltage reference. IACMPTOTAL = IACMP + IACMPREF. 4. In ACMPn_HYSTERESIS registers. 5. 100 mV differential drive. 6. In ACMPn_INPUTSEL register. silabs.com | Building a more connected world. Rev. 1.6 | 92 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.18 Digital to Analog Converter (VDAC) DRIVESTRENGTH = 2 unless otherwise specified. Primary VDAC output. Table 4.44. Digital to Analog Converter (VDAC) Parameter Symbol Test Condition Min Typ Max Unit Output voltage VDACOUT Single-Ended 0 -- VVREF V -VVREF -- VVREF V 500 ksps, 12-bit, DRIVESTRENGTH = 2, REFSEL = 4 -- 396 -- A 44.1 ksps, 12-bit, DRIVESTRENGTH = 1, REFSEL = 4 -- 72 -- A 200 Hz refresh rate, 12-bit Sample-Off mode in EM2, DRIVESTRENGTH = 2, REFSEL = 4, SETTLETIME = 0x02, WARMUPTIME = 0x0A -- 1.2 -- A Differential1 Current consumption including references (2 channels)2 IDAC Current from HFPERCLK3 IDAC_CLK -- 5.8 -- A/MHz Sample rate SRDAC -- -- 500 ksps DAC clock frequency fDAC -- -- 1 MHz Conversion time tDACCONV fDAC = 1MHz 2 -- -- s Settling time tDACSETTLE 50% fs step settling to 5 LSB -- 2.5 -- s Startup time tDACSTARTUP Enable to 90% fs output, settling to 10 LSB -- -- 12 s Output impedance ROUT DRIVESTRENGTH = 2, 0.4 V VOUT VOPA - 0.4 V, -8 mA < IOUT < 8 mA, Full supply range -- 2 -- DRIVESTRENGTH = 0 or 1, 0.4 V VOUT VOPA - 0.4 V, -400 A < IOUT < 400 A, Full supply range -- 2 -- DRIVESTRENGTH = 2, 0.1 V VOUT VOPA - 0.1 V, -2 mA < IOUT < 2 mA, Full supply range -- 2 -- DRIVESTRENGTH = 0 or 1, 0.1 V VOUT VOPA - 0.1 V, -100 A < IOUT < 100 A, Full supply range -- 2 -- Vout = 50% fs. DC -- 65.5 -- dB Power supply rejection ratio4 PSRR silabs.com | Building a more connected world. Rev. 1.6 | 93 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Min Typ Max Unit 500 ksps, single-ended, internal 1.25V reference -- 60.4 -- dB 500 ksps, single-ended, internal 2.5V reference -- 61.6 -- dB 500 ksps, single-ended, 3.3V VDD reference -- 64.0 -- dB 500 ksps, differential, internal 1.25V reference -- 63.3 -- dB 500 ksps, differential, internal 2.5V reference -- 64.4 -- dB 500 ksps, differential, 3.3V VDD reference -- 65.8 -- dB Signal to noise and distortion SNDRDAC_BAND 500 ksps, single-ended, internal ratio (1 kHz sine wave), 1.25V reference Noise band limited to 22 kHz 500 ksps, single-ended, internal 2.5V reference -- 65.3 -- dB -- 66.7 -- dB 500 ksps, single-ended, 3.3V VDD reference -- 70.0 -- dB 500 ksps, differential, internal 1.25V reference -- 67.8 -- dB 500 ksps, differential, internal 2.5V reference -- 69.0 -- dB 500 ksps, differential, 3.3V VDD reference -- 68.5 -- dB -- 70.2 -- dB Signal to noise and distortion SNDRDAC ratio (1 kHz sine wave), Noise band limited to 250 kHz Test Condition Total harmonic distortion THD Differential non-linearity5 DNLDAC -0.99 -- 1 LSB Intergral non-linearity INLDAC -4 -- 4 LSB Offset error6 VOFFSET T = 25 C -8 -- 8 mV Across operating temperature range -25 -- 25 mV T = 25 C, Low-noise internal reference (REFSEL = 1V25LN or 2V5LN) -2.5 -- 2.5 % T = 25 C, Internal reference (REFSEL = 1V25 or 2V5) -5 -- 5 % T = 25 C, External reference (REFSEL = VDD or EXT) -1.8 -- 1.8 % Across operating temperature range, Low-noise internal reference (REFSEL = 1V25LN or 2V5LN) -3.5 -- 3.5 % Across operating temperature range, Internal reference (REFSEL = 1V25 or 2V5) -7.5 -- 7.5 % Across operating temperature range, External reference (REFSEL = VDD or EXT) -2.0 -- 2.0 % Gain error6 VGAIN silabs.com | Building a more connected world. Rev. 1.6 | 94 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol External load capactiance, OUTSCALE=0 CLOAD Test Condition Min Typ Max Unit -- -- 75 pF Note: 1. In differential mode, the output is defined as the difference between two single-ended outputs. Absolute voltage on each output is limited to the single-ended range. 2. Supply current specifications are for VDAC circuitry operating with static output only and do not include current required to drive the load. 3. Current from HFPERCLK is dependent on HFPERCLK frequency. This current contributes to the total supply current used when the clock to the DAC peripheral is enabled in the CMU. 4. PSRR calculated as 20 * log10(VDD / VOUT), VDAC output at 90% of full scale 5. Entire range is monotonic and has no missing codes. 6. Gain is calculated by measuring the slope from 10% to 90% of full scale. Offset is calculated by comparing actual VDAC output at 10% of full scale to ideal VDAC output at 10% of full scale with the measured gain. silabs.com | Building a more connected world. Rev. 1.6 | 95 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.19 Current Digital to Analog Converter (IDAC) Table 4.45. Current Digital to Analog Converter (IDAC) Parameter Symbol Number of ranges NIDAC_RANGES Output current IIDAC_OUT Linear steps within each range NIDAC_STEPS Step size SSIDAC Total accuracy, STEPSEL1 = ACCIDAC 0x10 Start up time tIDAC_SU silabs.com | Building a more connected world. Test Condition Min Typ Max Unit -- 4 -- ranges RANGESEL1 = RANGE0 0.05 -- 1.6 A RANGESEL1 = RANGE1 1.6 -- 4.7 A RANGESEL1 = RANGE2 0.5 -- 16 A RANGESEL1 = RANGE3 2 -- 64 A -- 32 -- steps RANGESEL1 = RANGE0 -- 50 -- nA RANGESEL1 = RANGE1 -- 100 -- nA RANGESEL1 = RANGE2 -- 500 -- nA RANGESEL1 = RANGE3 -- 2 -- A EM0 or EM1, AVDD=3.3 V, T = 25 C -3 -- 3 % EM0 or EM1, Across operating temperature range -18 -- 22 % EM2 or EM3, Source mode, RANGESEL1 = RANGE0, AVDD=3.3 V, T = 25 C -- -2 -- % EM2 or EM3, Source mode, RANGESEL1 = RANGE1, AVDD=3.3 V, T = 25 C -- -1.7 -- % EM2 or EM3, Source mode, RANGESEL1 = RANGE2, AVDD=3.3 V, T = 25 C -- -0.8 -- % EM2 or EM3, Source mode, RANGESEL1 = RANGE3, AVDD=3.3 V, T = 25 C -- -0.5 -- % EM2 or EM3, Sink mode, RANGESEL1 = RANGE0, AVDD=3.3 V, T = 25 C -- -0.7 -- % EM2 or EM3, Sink mode, RANGESEL1 = RANGE1, AVDD=3.3 V, T = 25 C -- -0.6 -- % EM2 or EM3, Sink mode, RANGESEL1 = RANGE2, AVDD=3.3 V, T = 25 C -- -0.5 -- % EM2 or EM3, Sink mode, RANGESEL1 = RANGE3, AVDD=3.3 V, T = 25 C -- -0.5 -- % Output within 1% of steady state value -- 5 -- s Rev. 1.6 | 96 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Settling time, (output settled tIDAC_SETTLE within 1% of steady state value), Current consumption2 IIDAC Output voltage compliance in ICOMP_SRC source mode, source current change relative to current sourced at 0 V Output voltage compliance in ICOMP_SINK sink mode, sink current change relative to current sunk at IOVDD Test Condition Min Typ Max Unit Range setting is changed -- 5 -- s Step value is changed -- 1 -- s EM0 or EM1 Source mode, excluding output current, Across operating temperature range -- 11 18 A EM0 or EM1 Sink mode, excluding output current, Across operating temperature range -- 13 21 A EM2 or EM3 Source mode, excluding output current, T = 25 C -- 0.023 -- A EM2 or EM3 Sink mode, excluding output current, T = 25 C -- 0.041 -- A EM2 or EM3 Source mode, excluding output current, T 85 C -- 11 -- A EM2 or EM3 Sink mode, excluding output current, T 85 C -- 13 -- A RANGESEL1 = RANGE0, output voltage = min(VIOVDD, VAVDD2-100 mV) -- 0.11 -- % RANGESEL1 = RANGE1, output voltage = min(VIOVDD, VAVDD2-100 mV) -- 0.06 -- % RANGESEL1 = RANGE2, output voltage = min(VIOVDD, VAVDD2-150 mV) -- 0.04 -- % RANGESEL1 = RANGE3, output voltage = min(VIOVDD, VAVDD2-250 mV) -- 0.03 -- % RANGESEL1 = RANGE0, output voltage = 100 mV -- 0.12 -- % RANGESEL1 = RANGE1, output voltage = 100 mV -- 0.05 -- % RANGESEL1 = RANGE2, output voltage = 150 mV -- 0.04 -- % RANGESEL1 = RANGE3, output voltage = 250 mV -- 0.03 -- % Note: 1. In IDAC_CURPROG register. 2. The IDAC is supplied by either AVDD, DVDD, or IOVDD based on the setting of ANASW in the EMU_PWRCTRL register and PWRSEL in the IDAC_CTRL register. Setting PWRSEL to 1 selects IOVDD. With PWRSEL cleared to 0, ANASW selects between AVDD (0) and DVDD (1). silabs.com | Building a more connected world. Rev. 1.6 | 97 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.20 Capacitive Sense (CSEN) Table 4.46. Capacitive Sense (CSEN) Parameter Symbol Test Condition Single conversion time (1x accumulation) tCNV Maximum external capacitive CEXTMAX load Min Typ Max Unit 12-bit SAR Conversions -- 20.2 -- s 16-bit SAR Conversions -- 26.4 -- s Delta Modulation Conversion (single comparison) -- 1.55 -- s IREFPROG=7 (Gain = 1x), including routing parasitics -- 68 -- pF IREFPROG=0 (Gain = 10x), including routing parasitics -- 680 -- pF -- 1 -- k 12-bit SAR conversions, 20 ms conversion rate, IREFPROG=7 (Gain = 1x), 10 channels bonded (total capacitance of 330 pF)1 -- 326 -- nA Delta Modulation conversions, 20 ms conversion rate, IREFPROG=7 (Gain = 1x), 10 channels bonded (total capacitance of 330 pF)1 -- 226 -- nA 12-bit SAR conversions, 200 ms conversion rate, IREFPROG=7 (Gain = 1x), 10 channels bonded (total capacitance of 330 pF)1 -- 33 -- nA Delta Modulation conversions, 200 ms conversion rate, IREFPROG=7 (Gain = 1x), 10 channels bonded (total capacitance of 330 pF)1 -- 25 -- nA 12-bit SAR conversions, 20 ms scan rate, IREFPROG=0 (Gain = 10x), 8 samples per scan1 -- 690 -- nA Delta Modulation conversions, 20 ms scan rate, 8 comparisons per sample (DMCR = 1, DMR = 2), IREFPROG=0 (Gain = 10x), 8 samples per scan1 -- 515 -- nA 12-bit SAR conversions, 200 ms scan rate, IREFPROG=0 (Gain = 10x), 8 samples per scan1 -- 79 -- nA Delta Modulation conversions, 200 ms scan rate, 8 comparisons per sample (DMCR = 1, DMR = 2), IREFPROG=0 (Gain = 10x), 8 samples per scan1 -- 57 -- nA Maximum external series im- REXTMAX pedance Supply current, EM2 bonded ICSEN_BOND conversions, WARMUPMODE=NORMAL, WARMUPCNT=0 Supply current, EM2 scan conversions, WARMUPMODE=NORMAL, WARMUPCNT=0 ICSEN_EM2 silabs.com | Building a more connected world. Rev. 1.6 | 98 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Supply current, continuous conversions, WARMUPMODE=KEEPCSENWARM ICSEN_ACTIVE SAR or Delta Modulation conversions of 33 pF capacitor, IREFPROG=0 (Gain = 10x), always on -- 90.5 -- A HFPERCLK supply current ICSEN_HFPERCLK Current contribution from HFPERCLK when clock to CSEN block is enabled. -- 2.25 -- A/MHz Note: 1. Current is specified with a total external capacitance of 33 pF per channel. Average current is dependent on how long the peripheral is actively sampling channels within the scan period, and scales with the number of samples acquired. Supply current for a specific application can be estimated by multiplying the current per sample by the total number of samples per period (total_current = single_sample_current * (number_of_channels * accumulation)). silabs.com | Building a more connected world. Rev. 1.6 | 99 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.21 Operational Amplifier (OPAMP) Unless otherwise indicated, specified conditions are: Non-inverting input configuration, VDD = 3.3 V, DRIVESTRENGTH = 2, MAINOUTEN = 1, CLOAD = 75 pF with OUTSCALE = 0, or CLOAD = 37.5 pF with OUTSCALE = 1. Unit gain buffer and 3X-gain connection as specified in table footnotes1 2. Table 4.47. Operational Amplifier (OPAMP) Parameter Symbol Test Condition Supply voltage (from AVDD) VOPA HCMDIS = 0, Rail-to-rail input range Input voltage VIN Min Typ Max Unit 2 -- 3.8 V HCMDIS = 1 1.62 -- 3.8 V HCMDIS = 0, Rail-to-rail input range VVSS -- VOPA V HCMDIS = 1 VVSS -- VOPA-1.2 V Input impedance RIN 100 -- -- M Output voltage VOUT VVSS -- VOPA V Load capacitance3 CLOAD OUTSCALE = 0 -- -- 75 pF OUTSCALE = 1 -- -- 37.5 pF DRIVESTRENGTH = 2 or 3, 0.4 V VOUT VOPA - 0.4 V, -8 mA < IOUT < 8 mA, Buffer connection, Full supply range -- 0.25 -- DRIVESTRENGTH = 0 or 1, 0.4 V VOUT VOPA - 0.4 V, -400 A < IOUT < 400 A, Buffer connection, Full supply range -- 0.6 -- DRIVESTRENGTH = 2 or 3, 0.1 V VOUT VOPA - 0.1 V, -2 mA < IOUT < 2 mA, Buffer connection, Full supply range -- 0.4 -- DRIVESTRENGTH = 0 or 1, 0.1 V VOUT VOPA - 0.1 V, -100 A < IOUT < 100 A, Buffer connection, Full supply range -- 1 -- Buffer connection 0.99 1 1.01 - 3x Gain connection 2.93 2.99 3.05 - 16x Gain connection 15.07 15.7 16.33 - DRIVESTRENGTH = 3, OUTSCALE = 0 -- 580 -- A DRIVESTRENGTH = 2, OUTSCALE = 0 -- 176 -- A DRIVESTRENGTH = 1, OUTSCALE = 0 -- 13 -- A DRIVESTRENGTH = 0, OUTSCALE = 0 -- 4.7 -- A Output impedance Internal closed-loop gain Active current4 ROUT GCL IOPA silabs.com | Building a more connected world. Rev. 1.6 | 100 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Open-loop gain GOL Loop unit-gain frequency5 Phase margin Output voltage noise UGF PM NOUT silabs.com | Building a more connected world. Min Typ Max Unit DRIVESTRENGTH = 3 -- 135 -- dB DRIVESTRENGTH = 2 -- 137 -- dB DRIVESTRENGTH = 1 -- 121 -- dB DRIVESTRENGTH = 0 -- 109 -- dB DRIVESTRENGTH = 3, Buffer connection -- 3.38 -- MHz DRIVESTRENGTH = 2, Buffer connection -- 0.9 -- MHz DRIVESTRENGTH = 1, Buffer connection -- 132 -- kHz DRIVESTRENGTH = 0, Buffer connection -- 34 -- kHz DRIVESTRENGTH = 3, 3x Gain connection -- 2.57 -- MHz DRIVESTRENGTH = 2, 3x Gain connection -- 0.71 -- MHz DRIVESTRENGTH = 1, 3x Gain connection -- 113 -- kHz DRIVESTRENGTH = 0, 3x Gain connection -- 28 -- kHz DRIVESTRENGTH = 3, Buffer connection -- 67 -- DRIVESTRENGTH = 2, Buffer connection -- 69 -- DRIVESTRENGTH = 1, Buffer connection -- 63 -- DRIVESTRENGTH = 0, Buffer connection -- 68 -- DRIVESTRENGTH = 3, Buffer connection, 10 Hz - 10 MHz -- 146 -- Vrms DRIVESTRENGTH = 2, Buffer connection, 10 Hz - 10 MHz -- 163 -- Vrms DRIVESTRENGTH = 1, Buffer connection, 10 Hz - 1 MHz -- 170 -- Vrms DRIVESTRENGTH = 0, Buffer connection, 10 Hz - 1 MHz -- 176 -- Vrms DRIVESTRENGTH = 3, 3x Gain connection, 10 Hz - 10 MHz -- 313 -- Vrms DRIVESTRENGTH = 2, 3x Gain connection, 10 Hz - 10 MHz -- 271 -- Vrms DRIVESTRENGTH = 1, 3x Gain connection, 10 Hz - 1 MHz -- 247 -- Vrms DRIVESTRENGTH = 0, 3x Gain connection, 10 Hz - 1 MHz -- 245 -- Vrms Rev. 1.6 | 101 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Slew rate6 SR DRIVESTRENGTH = 3, INCBW=17 -- 4.7 -- V/s DRIVESTRENGTH = 3, INCBW=0 -- 1.5 -- V/s DRIVESTRENGTH = 2, INCBW=17 -- 1.27 -- V/s DRIVESTRENGTH = 2, INCBW=0 -- 0.42 -- V/s DRIVESTRENGTH = 1, INCBW=17 -- 0.17 -- V/s DRIVESTRENGTH = 1, INCBW=0 -- 0.058 -- V/s DRIVESTRENGTH = 0, INCBW=17 -- 0.044 -- V/s DRIVESTRENGTH = 0, INCBW=0 -- 0.015 -- V/s Startup time8 TSTART DRIVESTRENGTH = 2 -- -- 12 s Input offset voltage VOSI DRIVESTRENGTH = 2 or 3, T = 25 C -2 -- 2 mV DRIVESTRENGTH = 1 or 0, T = 25 C -2 -- 2 mV DRIVESTRENGTH = 2 or 3, across operating temperature range -12 -- 12 mV DRIVESTRENGTH = 1 or 0, across operating temperature range -30 -- 30 mV DC power supply rejection ratio9 PSRRDC Input referred -- 70 -- dB DC common-mode rejection ratio9 CMRRDC Input referred -- 70 -- dB Total harmonic distortion THDOPA DRIVESTRENGTH = 2, 3x Gain connection, 1 kHz, VOUT = 0.1 V to VOPA - 0.1 V -- 90 -- dB DRIVESTRENGTH = 0, 3x Gain connection, 0.1 kHz, VOUT = 0.1 V to VOPA - 0.1 V -- 90 -- dB silabs.com | Building a more connected world. Rev. 1.6 | 102 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Parameter Symbol Test Condition Min Typ Max Unit Note: 1. Specified configuration for Unit gain buffer configuration is: INCBW = 0, HCMDIS = 0, RESINSEL = DISABLE. VINPUT = 0.5 V, VOUTPUT = 0.5 V. 2. Specified configuration for 3X-Gain configuration is: INCBW = 1, HCMDIS = 1, RESINSEL = VSS, VINPUT = 0.5 V, VOUTPUT = 1.5 V. Nominal voltage gain is 3. 3. If the maximum CLOAD is exceeded, an isolation resistor is required for stability. See AN0038 for more information. 4. Current into the load resistor is excluded. When the OPAMP is connected with closed-loop gain > 1, there will be extra current to drive the resistor feedback network. The internal resistor feedback network has total resistance of 143.5 kOhm, which will cause another ~10 A current when the OPAMP drives 1.5 V between output and ground. 5. In unit gain connection, UGF is the gain-bandwidth product of the OPAMP. In 3x Gain connection, UGF is the gain-bandwidth product of the OPAMP and 1/3 attenuation of the feedback network. 6. Step between 0.2V and VOPA-0.2V, 10%-90% rising/falling range. 7. When INCBW is set to 1 the OPAMP bandwidth is increased. This is allowed only when the non-inverting close-loop gain is 3, or the OPAMP may not be stable. 8. From enable to output settled. In sample-and-off mode, RC network after OPAMP will contribute extra delay. Settling error < 1mV. 9. When HCMDIS=1 and input common mode transitions the region from VOPA-1.4V to VOPA-1V, input offset will change. PSRR and CMRR specifications do not apply to this transition region. 4.1.22 Pulse Counter (PCNT) Table 4.48. Pulse Counter (PCNT) Parameter Symbol Test Condition Min Typ Max Unit Input frequency FIN Asynchronous Single and Quadrature Modes -- -- 20 MHz Sampled Modes with Debounce filter set to 0. -- -- 8 kHz Min Typ Max Unit 4.1.23 Analog Port (APORT) Table 4.49. Analog Port (APORT) Parameter Symbol Test Condition Supply current1 2 IAPORT Operation in EM0/EM1 -- 7 -- A Operation in EM2/EM3 -- 67 -- nA Note: 1. Supply current increase that occurs when an analog peripheral requests access to APORT. This current is not included in reported peripheral currents. Additional peripherals requesting access to APORT do not incur further current. 2. Specified current is for continuous APORT operation. In applications where the APORT is not requested continuously (e.g. periodic ACMP requests from LESENSE in EM2), the average current requirements can be estimated by mutiplying the duty cycle of the requests by the specified continuous current number. silabs.com | Building a more connected world. Rev. 1.6 | 103 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.24 I2C 4.1.24.1 I2C Standard-mode (Sm)1 Table 4.50. I2C Standard-mode (Sm)1 Parameter Symbol SCL clock frequency2 Test Condition Min Typ Max Unit fSCL 0 -- 100 kHz SCL clock low time tLOW 4.7 -- -- s SCL clock high time tHIGH 4 -- -- s SDA set-up time tSU_DAT 250 -- -- ns SDA hold time3 tHD_DAT 100 -- 3450 ns Repeated START condition set-up time tSU_STA 4.7 -- -- s (Repeated) START condition tHD_STA hold time 4 -- -- s STOP condition set-up time tSU_STO 4 -- -- s Bus free time between a STOP and START condition tBUF 4.7 -- -- s Note: 1. For CLHR set to 0 in the I2Cn_CTRL register. 2. For the minimum HFPERCLK frequency required in Standard-mode, refer to the I2C chapter in the reference manual. 3. The maximum SDA hold time (tHD_DAT) needs to be met only when the device does not stretch the low time of SCL (tLOW). silabs.com | Building a more connected world. Rev. 1.6 | 104 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.24.2 I2C Fast-mode (Fm)1 Table 4.51. I2C Fast-mode (Fm)1 Parameter Symbol SCL clock frequency2 Test Condition Min Typ Max Unit fSCL 0 -- 400 kHz SCL clock low time tLOW 1.3 -- -- s SCL clock high time tHIGH 0.6 -- -- s SDA set-up time tSU_DAT 100 -- -- ns SDA hold time3 tHD_DAT 100 -- 900 ns Repeated START condition set-up time tSU_STA 0.6 -- -- s (Repeated) START condition tHD_STA hold time 0.6 -- -- s STOP condition set-up time tSU_STO 0.6 -- -- s Bus free time between a STOP and START condition tBUF 1.3 -- -- s Note: 1. For CLHR set to 1 in the I2Cn_CTRL register. 2. For the minimum HFPERCLK frequency required in Fast-mode, refer to the I2C chapter in the reference manual. 3. The maximum SDA hold time (tHD,DAT) needs to be met only when the device does not stretch the low time of SCL (tLOW). silabs.com | Building a more connected world. Rev. 1.6 | 105 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.24.3 I2C Fast-mode Plus (Fm+)1 Table 4.52. I2C Fast-mode Plus (Fm+)1 Parameter Symbol SCL clock frequency2 Test Condition Min Typ Max Unit fSCL 0 -- 1000 kHz SCL clock low time tLOW 0.5 -- -- s SCL clock high time tHIGH 0.26 -- -- s SDA set-up time tSU_DAT 50 -- -- ns SDA hold time tHD_DAT 100 -- -- ns Repeated START condition set-up time tSU_STA 0.26 -- -- s (Repeated) START condition tHD_STA hold time 0.26 -- -- s STOP condition set-up time tSU_STO 0.26 -- -- s Bus free time between a STOP and START condition tBUF 0.5 -- -- s Note: 1. For CLHR set to 0 or 1 in the I2Cn_CTRL register. 2. For the minimum HFPERCLK frequency required in Fast-mode Plus, refer to the I2C chapter in the reference manual. silabs.com | Building a more connected world. Rev. 1.6 | 106 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.1.25 USART SPI SPI Master Timing Table 4.53. SPI Master Timing Parameter Symbol SCLK period 1 2 3 tSCLK CS to MOSI 1 2 Test Condition Min Typ Max Unit 2* tHFPERCLK -- -- ns tCS_MO -14.5 -- 13.5 ns SCLK to MOSI 1 2 tSCLK_MO -8.5 -- 8 ns MISO setup time 1 2 tSU_MI IOVDD = 1.62 V 92 -- -- ns IOVDD = 3.0 V 42 -- -- ns -10 -- -- ns tH_MI MISO hold time 1 2 Note: 1. Applies for both CLKPHA = 0 and CLKPHA = 1 (figure only shows CLKPHA = 0). 2. Measurement done with 8 pF output loading at 10% and 90% of VDD (figure shows 50% of VDD). 3. tHFPERCLK is one period of the selected HFPERCLK. CS tCS_MO tSCKL_MO SCLK CLKPOL = 0 tSCLK SCLK CLKPOL = 1 MOSI tSU_MI tH_MI MISO Figure 4.1. SPI Master Timing Diagram silabs.com | Building a more connected world. Rev. 1.6 | 107 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications SPI Slave Timing Table 4.54. SPI Slave Timing Parameter Symbol SCLK period 1 2 3 Test Condition Min Typ Max Unit tSCLK 6* tHFPERCLK -- -- ns SCLK high time1 2 3 tSCLK_HI 2.5 * tHFPERCLK -- -- ns SCLK low time1 2 3 tSCLK_LO 2.5 * tHFPERCLK -- -- ns CS active to MISO 1 2 tCS_ACT_MI 4 -- 70 ns CS disable to MISO 1 2 tCS_DIS_MI 4 -- 50 ns MOSI setup time 1 2 tSU_MO 8 -- -- ns MOSI hold time 1 2 3 tH_MO 7 -- -- ns SCLK to MISO 1 2 3 tSCLK_MI 10 + 1.5 * tHFPERCLK -- 65 + 2.5 * tHFPERCLK ns Note: 1. Applies for both CLKPHA = 0 and CLKPHA = 1 (figure only shows CLKPHA = 0). 2. Measurement done with 8 pF output loading at 10% and 90% of VDD (figure shows 50% of VDD). 3. tHFPERCLK is one period of the selected HFPERCLK. CS tCS_ACT_MI tCS_DIS_MI SCLK CLKPOL = 0 SCLK CLKPOL = 1 tSCLK_HI tSU_MO tSCLK_LO tSCLK tH_MO MOSI tSCLK_MI MISO Figure 4.2. SPI Slave Timing Diagram 4.2 Typical Performance Curves Typical performance curves indicate typical characterized performance under the stated conditions. silabs.com | Building a more connected world. Rev. 1.6 | 108 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.2.1 Supply Current Figure 4.3. EM0 Active Mode Typical Supply Current vs. Temperature silabs.com | Building a more connected world. Rev. 1.6 | 109 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Figure 4.4. EM1 Sleep Mode Typical Supply Current vs. Temperature Typical supply current for EM2, EM3 and EM4H using standard software libraries from Silicon Laboratories. silabs.com | Building a more connected world. Rev. 1.6 | 110 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Figure 4.5. EM2, EM3, EM4H and EM4S Typical Supply Current vs. Temperature silabs.com | Building a more connected world. Rev. 1.6 | 111 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Figure 4.6. EM0 and EM1 Mode Typical Supply Current vs. Supply Typical supply current for EM2, EM3 and EM4H using standard software libraries from Silicon Laboratories. silabs.com | Building a more connected world. Rev. 1.6 | 112 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Figure 4.7. EM2, EM3, EM4H and EM4S Typical Supply Current vs. Supply silabs.com | Building a more connected world. Rev. 1.6 | 113 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.2.2 DC-DC Converter Default test conditions: CCM mode, LDCDC = 4.7 H, CDCDC = 4.7 F, VDCDC_I = 3.3 V, VDCDC_O = 1.8 V, FDCDC_LN = 7 MHz Figure 4.8. DC-DC Converter Typical Performance Characteristics silabs.com | Building a more connected world. Rev. 1.6 | 114 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Load Step Response in LN (CCM) mode (Heavy Drive) LN (CCM) and LP mode transition (load: 5mA) DVDD DVDD 60mV/div offset:1.8V 20mV/div offset:1.8V 100mA VSW ILOAD 1mA 2V/div offset:1.8V 100s/div 10s/div Figure 4.9. DC-DC Converter Transition Waveforms silabs.com | Building a more connected world. Rev. 1.6 | 115 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications 4.2.3 2.4 GHz Radio Figure 4.10. 2.4 GHz RF Transmitter Output Power silabs.com | Building a more connected world. Rev. 1.6 | 116 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Electrical Specifications Figure 4.11. 2.4 GHz RF Receiver Sensitivity silabs.com | Building a more connected world. Rev. 1.6 | 117 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Typical Connection Diagrams 5. Typical Connection Diagrams 5.1 Power Typical power supply connections for direct supply, without using the internal DC-DC converter, are shown in the following figure. VDD Main Supply + - VREGVDD AVDD VREGSW IOVDD HFXTAL_N VREGVSS HFXTAL_P DVDD LFXTAL_N LFXTAL_P DECOUPLE RFVDD PAVDD Figure 5.1. EFR32BG12 Typical Application Circuit: Direct Supply Configuration without DC-DC converter Typical power supply circuits using the internal DC-DC converter are shown below. The MCU operates from the DC-DC converter supply. For low RF transmit power applications less than 13dBm, the RF PA may be supplied by the DC-DC converter. For OPNs supporting high power RF transmission, the RF PA must be directly supplied by VDD for RF transmit power greater than 13 dBm. VDD Main Supply + - VREGVDD VDCDC AVDD VREGSW IOVDD HFXTAL_N VREGVSS HFXTAL_P DVDD LFXTAL_N LFXTAL_P DECOUPLE RFVDD PAVDD Figure 5.2. EFR32BG12 Typical Application Circuit: Configuration with DC-DC converter (PAVDD from VDCDC) silabs.com | Building a more connected world. Rev. 1.6 | 118 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Typical Connection Diagrams VDD Main Supply + - VREGVDD VDCDC AVDD VREGSW IOVDD HFXTAL_N VREGVSS HFXTAL_P DVDD LFXTAL_N LFXTAL_P DECOUPLE RFVDD PAVDD Figure 5.3. EFR32BG12 Typical Application Circuit: Configuration with DC-DC converter (PAVDD from VDD) silabs.com | Building a more connected world. Rev. 1.6 | 119 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Typical Connection Diagrams 5.2 RF Matching Networks Typical RF matching network circuit diagrams are shown in Figure 5.4 Typical 2.4 GHz RF impedance-matching network circuits on page 120 for applications in the 2.4GHz band, and in Figure 5.5 Typical Sub-GHz RF impedance-matching network circuits on page 120 for applications in the sub-GHz band. Application-specific component values can be found in application notes AN923: EFR32 subGHz Matching Guide and AN930: EFR32 2.4 GHz Matching Guide. For low RF transmit power applications less than 13dBm, the twoelement match is recommended. For OPNs supporting high power RF transmission, the four-element match is recommended for high RF transmit power (> 13dBm). 4-Element Match for 2.4GHz Band 2-Element Match for 2.4GHz Band PAVDD PAVDD PAVDD PAVDD L0 2G4RF_IOP L1 2G4RF_IOP 50 C0 2G4RF_ION L0 50 C0 2G4RF_ION C1 Figure 5.4. Typical 2.4 GHz RF impedance-matching network circuits Sub-GHz Match Topology I (169-500 MHz) PAVDD L1 L2 C0 L3 C5 L5 L6 L7 SUBGRF_IN 50 C2 C7 C4 L0 C8 C9 C10 C3 SUBGRF_IP C1 L4 C6 BAL1 SUBGRF_ON SUBGRF_OP Sub-GHz Match Topology 2 (500-915 MHz) C0 L3 PAVDD L5 L6 50 SUBGRF_IN L0 C4 C7 C8 C9 SUBGRF_IP C1 L4 BAL1 SUBGRF_ON SUBGRF_OP Figure 5.5. Typical Sub-GHz RF impedance-matching network circuits silabs.com | Building a more connected world. Rev. 1.6 | 120 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Typical Connection Diagrams 5.3 Other Connections Other components or connections may be required to meet the system-level requirements. Application Note AN0002: "Hardware Design Considerations" contains detailed information on these connections. Application Notes can be accessed on the Silicon Labs website (www.silabs.com/32bit-appnotes). silabs.com | Building a more connected world. Rev. 1.6 | 121 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions 6. Pin Definitions 6.1 BGA125 2.4 GHz and Sub-GHz Device Pinout Figure 6.1. BGA125 2.4 GHz and Sub-GHz Device Pinout The following table provides package pin connections and general descriptions of pin functionality. For detailed information on the supported features for each GPIO pin, see 6.7 GPIO Functionality Table or 6.8 Alternate Functionality Overview. Table 6.1. BGA125 2.4 GHz and Sub-GHz Device Pinout Pin Name Pin(s) Description Pin Name Pin(s) Description PF3 A1 GPIO (5V) PF1 A2 GPIO (5V) PC5 A3 GPIO (5V) PC3 A4 GPIO (5V) PC0 A5 GPIO (5V) PC11 A6 GPIO (5V) PC9 A7 GPIO (5V) PC7 A8 GPIO (5V) silabs.com | Building a more connected world. Rev. 1.6 | 122 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Pin Name Pin(s) Description DECOUPLE A9 Decouple output for on-chip voltage regulator. An external decoupling capacitor is required at this pin. This pin should not be used to power any external circuits. VREGVDD A11 Voltage regulator VDD input VREGVSS A13 B11 B12 PF2 Pin Name Pin(s) Description DVDD A10 Digital power supply. VREGSW A12 DCDC regulator switching node Voltage regulator VSS PF8 B1 GPIO (5V) B2 GPIO (5V) PF0 B3 GPIO (5V) PC4 B4 GPIO (5V) PC1 B5 GPIO (5V) PJ14 B6 GPIO (5V) PC10 B7 GPIO (5V) PC8 B8 GPIO (5V) PC6 B9 GPIO (5V) IOVDD B10 F2 F11 M12 Digital IO power supply. AVDD B13 Analog power supply. PF11 C1 GPIO (5V) PF10 C2 GPIO (5V) PF9 C3 GPIO (5V) PC2 C5 GPIO (5V) PJ15 C6 GPIO (5V) PB15 C10 GPIO PB14 C11 GPIO PB13 C12 GPIO PB12 C13 GPIO PF14 D1 GPIO (5V) PF13 D2 GPIO (5V) PF12 D3 GPIO (5V) PB11 D11 GPIO PB10 D12 GPIO (5V) PB9 D13 GPIO (5V) PK1 E1 GPIO (5V) PK0 E2 GPIO PF15 E3 GPIO (5V) silabs.com | Building a more connected world. Rev. 1.6 | 123 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Pin Name Pin(s) Description Pin Name Pin(s) Description VSS E5 E6 E7 E8 E9 F5 F6 F7 F8 F9 G5 G6 G7 G8 G9 H5 H6 H7 H8 H9 J5 J6 J7 J8 J9 K2 L2 Ground PB8 E12 GPIO (5V) PB7 E13 GPIO (5V) PK2 F1 GPIO (5V) PB6 F12 GPIO (5V) PI3 F13 GPIO (5V) PF5 G1 GPIO (5V) PF4 G2 GPIO (5V) PI2 G11 GPIO (5V) PI1 G12 GPIO (5V) PI0 G13 GPIO (5V) PF7 H1 GPIO (5V) PF6 H2 GPIO (5V) PA9 H12 GPIO (5V) PA8 H13 GPIO (5V) RFVDD J1 J2 Radio power supply PA7 J11 GPIO (5V) PA6 J12 GPIO (5V) PA5 J13 GPIO (5V) HFXTAL_N K1 High Frequency Crystal input pin. PA4 K12 GPIO PA3 K13 GPIO HFXTAL_P L1 High Frequency Crystal output pin. BODEN L10 Brown-Out Detector Enable. This pin may be left disconnected or tied to AVDD. PA2 L12 GPIO PA1 L13 GPIO RESETn M1 Reset input, active low. This pin is internally pulled up to AVDD. To apply an external reset source to this pin, it is required to only drive this pin low during reset, and let the internal pull-up ensure that reset is released. RFVSS M2 M3 M4 M5 N5 Radio Ground PAVSS M6 M7 Power Amplifier (PA) voltage regulator VSS PAVDD M8 N8 Power Amplifier (PA) voltage regulator VDD input PD9 M9 GPIO (5V) PD11 M10 GPIO (5V) PD13 M11 GPIO PA0 M13 GPIO silabs.com | Building a more connected world. Rev. 1.6 | 124 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Pin Name Pin(s) Description Pin Name Pin(s) Description SUBGRF_OP N1 Sub GHz Differential RF output, positive path. SUBGRF_ON N2 Sub GHz Differential RF output, negative path. SUBGRF_IP N3 Sub GHz Differential RF input, positive path. SUBGRF_IN N4 Sub GHz Differential RF input, negative path. 2G4RF_ION N6 2.4 GHz Differential RF input/output, negative path. This pin should be externally grounded. 2G4RF_IOP N7 2.4 GHz Differential RF input/output, positive path. PD8 N9 GPIO (5V) PD10 N10 GPIO (5V) PD12 N11 GPIO (5V) PD14 N12 GPIO PD15 N13 GPIO Note: 1. GPIO with 5V tolerance are indicated by (5V). silabs.com | Building a more connected world. Rev. 1.6 | 125 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions 6.2 BGA125 2.4 GHz Device Pinout Figure 6.2. BGA125 2.4 GHz Device Pinout The following table provides package pin connections and general descriptions of pin functionality. For detailed information on the supported features for each GPIO pin, see 6.7 GPIO Functionality Table or 6.8 Alternate Functionality Overview. Table 6.2. BGA125 2.4 GHz Device Pinout Pin Name Pin(s) Description Pin Name Pin(s) Description PF3 A1 GPIO (5V) PF1 A2 GPIO (5V) PC5 A3 GPIO (5V) PC3 A4 GPIO (5V) PC0 A5 GPIO (5V) PC11 A6 GPIO (5V) PC9 A7 GPIO (5V) PC7 A8 GPIO (5V) A9 Decouple output for on-chip voltage regulator. An external decoupling capacitor is required at this pin. This pin should not be used to power any external circuits. DVDD A10 Digital power supply. DECOUPLE silabs.com | Building a more connected world. Rev. 1.6 | 126 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Pin Name Pin(s) Description VREGVDD A11 Voltage regulator VDD input VREGVSS A13 B11 B12 PF2 Pin Name Pin(s) Description VREGSW A12 DCDC regulator switching node Voltage regulator VSS PF8 B1 GPIO (5V) B2 GPIO (5V) PF0 B3 GPIO (5V) PC4 B4 GPIO (5V) PC1 B5 GPIO (5V) PJ14 B6 GPIO (5V) PC10 B7 GPIO (5V) PC8 B8 GPIO (5V) PC6 B9 GPIO (5V) IOVDD B10 F2 F11 M12 Digital IO power supply. AVDD B13 Analog power supply. PF11 C1 GPIO (5V) PF10 C2 GPIO (5V) PF9 C3 GPIO (5V) PC2 C5 GPIO (5V) PJ15 C6 GPIO (5V) PB15 C10 GPIO PB14 C11 GPIO PB13 C12 GPIO PB12 C13 GPIO PF14 D1 GPIO (5V) PF13 D2 GPIO (5V) PF12 D3 GPIO (5V) PB11 D11 GPIO PB10 D12 GPIO (5V) PB9 D13 GPIO (5V) PK1 E1 GPIO (5V) PK0 E2 GPIO PF15 E3 GPIO (5V) VSS E5 E6 E7 E8 E9 F5 F6 F7 F8 F9 G5 G6 G7 G8 G9 H5 H6 H7 H8 H9 J5 J6 J7 J8 J9 K2 L2 Ground PB8 E12 GPIO (5V) PB7 E13 GPIO (5V) PK2 F1 GPIO (5V) PB6 F12 GPIO (5V) PI3 F13 GPIO (5V) silabs.com | Building a more connected world. Rev. 1.6 | 127 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Pin Name Pin(s) Description Pin Name Pin(s) Description PF5 G1 GPIO (5V) PF4 G2 GPIO (5V) PI2 G11 GPIO (5V) PI1 G12 GPIO (5V) PI0 G13 GPIO (5V) PF7 H1 GPIO (5V) PF6 H2 GPIO (5V) PA9 H12 GPIO (5V) PA8 H13 GPIO (5V) RFVDD J1 J2 Radio power supply PA7 J11 GPIO (5V) PA6 J12 GPIO (5V) PA5 J13 GPIO (5V) HFXTAL_N K1 High Frequency Crystal input pin. PA4 K12 GPIO PA3 K13 GPIO HFXTAL_P L1 High Frequency Crystal output pin. BODEN L10 Brown-Out Detector Enable. This pin may be left disconnected or tied to AVDD. PA2 L12 GPIO PA1 L13 GPIO RESETn M1 Reset input, active low. This pin is internally pulled up to AVDD. To apply an external reset source to this pin, it is required to only drive this pin low during reset, and let the internal pull-up ensure that reset is released. RFVSS M2 M3 M4 M5 N5 Radio Ground PAVSS M6 M7 Power Amplifier (PA) voltage regulator VSS PAVDD M8 N8 Power Amplifier (PA) voltage regulator VDD input PD9 M9 GPIO (5V) PD11 M10 GPIO (5V) PD13 M11 GPIO PA0 M13 GPIO NC N1 N2 N3 N4 No Connect. 2G4RF_ION N6 2.4 GHz Differential RF input/output, negative path. This pin should be externally grounded. 2G4RF_IOP N7 2.4 GHz Differential RF input/output, positive path. PD8 N9 GPIO (5V) PD10 N10 GPIO (5V) PD12 N11 GPIO (5V) PD14 N12 GPIO PD15 N13 GPIO Note: 1. GPIO with 5V tolerance are indicated by (5V). silabs.com | Building a more connected world. Rev. 1.6 | 128 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions 6.3 QFN68 2.4 GHz and Sub-GHz Device Pinout Figure 6.3. QFN68 2.4 GHz and Sub-GHz Device Pinout The following table provides package pin connections and general descriptions of pin functionality. For detailed information on the supported features for each GPIO pin, see 6.7 GPIO Functionality Table or 6.8 Alternate Functionality Overview. Table 6.3. QFN68 2.4 GHz and Sub-GHz Device Pinout Pin Name Pin(s) Description Pin Name Pin(s) Description VSS 0 Ground PC5 1 GPIO (5V) PF0 2 GPIO (5V) PF1 3 GPIO (5V) PF2 4 GPIO (5V) PF3 5 GPIO (5V) PF8 6 GPIO (5V) PF9 7 GPIO (5V) PF10 8 GPIO (5V) IOVDD 9 41 57 Digital IO power supply. PF4 10 GPIO (5V) PF5 11 GPIO (5V) silabs.com | Building a more connected world. Rev. 1.6 | 129 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Pin Name Pin(s) Description PF6 12 GPIO (5V) RFVDD 14 Radio power supply Pin Name Pin(s) Description PF7 13 GPIO (5V) HFXTAL_N 15 High Frequency Crystal input pin. RESETn 17 Reset input, active low. This pin is internally pulled up to AVDD. To apply an external reset source to this pin, it is required to only drive this pin low during reset, and let the internal pull-up ensure that reset is released. HFXTAL_P 16 High Frequency Crystal output pin. SUBGRF_OP 18 Sub GHz Differential RF output, positive path. SUBGRF_ON 19 Sub GHz Differential RF output, negative path. SUBGRF_IP 20 Sub GHz Differential RF input, positive path. SUBGRF_IN 21 Sub GHz Differential RF input, negative path. RFVSS 22 Radio Ground PAVSS 23 Power Amplifier (PA) voltage regulator VSS 2G4RF_ION 24 2.4 GHz Differential RF input/output, negative path. This pin should be externally grounded. 2G4RF_IOP 25 2.4 GHz Differential RF input/output, positive path. PAVDD 26 Power Amplifier (PA) voltage regulator VDD input PD8 27 GPIO (5V) PD9 28 GPIO (5V) PD10 29 GPIO (5V) PD11 30 GPIO (5V) PD12 31 GPIO (5V) PD13 32 GPIO PD14 33 GPIO PD15 34 GPIO PA0 35 GPIO PA1 36 GPIO PA2 37 GPIO PA3 38 GPIO PA4 39 GPIO PA5 40 GPIO (5V) PB7 42 GPIO (5V) PB8 43 GPIO (5V) PB9 44 GPIO (5V) PB10 45 GPIO (5V) PB11 46 GPIO PB12 47 GPIO PB13 48 GPIO AVDD 49 Analog power supply. PB14 50 GPIO PB15 51 GPIO VREGVSS 52 Voltage regulator VSS VREGSW 53 DCDC regulator switching node VREGVDD 54 Voltage regulator VDD input DECOUPLE 56 Decouple output for on-chip voltage regulator. An external decoupling capacitor is required at this pin. This pin should not be used to power any external circuits. DVDD 55 Digital power supply. PC6 58 GPIO (5V) PC7 59 GPIO (5V) PC8 60 GPIO (5V) PC9 61 GPIO (5V) PC10 62 GPIO (5V) PC11 63 GPIO (5V) PC0 64 GPIO (5V) PC1 65 GPIO (5V) PC2 66 GPIO (5V) PC3 67 GPIO (5V) PC4 68 GPIO (5V) silabs.com | Building a more connected world. Rev. 1.6 | 130 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Pin Name Pin(s) Description Pin Name Pin(s) Description Note: 1. GPIO with 5V tolerance are indicated by (5V). silabs.com | Building a more connected world. Rev. 1.6 | 131 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions 6.4 QFN68 2.4 GHz Device Pinout Figure 6.4. QFN68 2.4 GHz Device Pinout The following table provides package pin connections and general descriptions of pin functionality. For detailed information on the supported features for each GPIO pin, see 6.7 GPIO Functionality Table or 6.8 Alternate Functionality Overview. Table 6.4. QFN68 2.4 GHz Device Pinout Pin Name Pin(s) Description Pin Name Pin(s) Description VSS 0 Ground PC5 1 GPIO (5V) PF0 2 GPIO (5V) PF1 3 GPIO (5V) PF2 4 GPIO (5V) PF3 5 GPIO (5V) PF8 6 GPIO (5V) PF9 7 GPIO (5V) PF10 8 GPIO (5V) IOVDD 9 41 57 Digital IO power supply. PF4 10 GPIO (5V) PF5 11 GPIO (5V) silabs.com | Building a more connected world. Rev. 1.6 | 132 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Pin Name Pin(s) Description PF6 12 GPIO (5V) RFVDD 14 Radio power supply Pin Name Pin(s) Description PF7 13 GPIO (5V) HFXTAL_N 15 High Frequency Crystal input pin. HFXTAL_P 16 High Frequency Crystal output pin. RESETn 17 Reset input, active low. This pin is internally pulled up to AVDD. To apply an external reset source to this pin, it is required to only drive this pin low during reset, and let the internal pull-up ensure that reset is released. NC 18 19 20 21 No Connect. RFVSS 22 Radio Ground PAVSS 23 Power Amplifier (PA) voltage regulator VSS 2G4RF_ION 24 2.4 GHz Differential RF input/output, negative path. This pin should be externally grounded. 2G4RF_IOP 25 2.4 GHz Differential RF input/output, positive path. PAVDD 26 Power Amplifier (PA) voltage regulator VDD input PD8 27 GPIO (5V) PD9 28 GPIO (5V) PD10 29 GPIO (5V) PD11 30 GPIO (5V) PD12 31 GPIO (5V) PD13 32 GPIO PD14 33 GPIO PD15 34 GPIO PA0 35 GPIO PA1 36 GPIO PA2 37 GPIO PA3 38 GPIO PA4 39 GPIO PA5 40 GPIO (5V) PB7 42 GPIO (5V) PB8 43 GPIO (5V) PB9 44 GPIO (5V) PB10 45 GPIO (5V) PB11 46 GPIO PB12 47 GPIO PB13 48 GPIO AVDD 49 Analog power supply. PB14 50 GPIO PB15 51 GPIO VREGVSS 52 Voltage regulator VSS VREGSW 53 DCDC regulator switching node VREGVDD 54 Voltage regulator VDD input DVDD 55 Digital power supply. DECOUPLE 56 Decouple output for on-chip voltage regulator. An external decoupling capacitor is required at this pin. This pin should not be used to power any external circuits. PC6 58 GPIO (5V) PC7 59 GPIO (5V) PC8 60 GPIO (5V) PC9 61 GPIO (5V) PC10 62 GPIO (5V) PC11 63 GPIO (5V) PC0 64 GPIO (5V) PC1 65 GPIO (5V) PC2 66 GPIO (5V) PC3 67 GPIO (5V) PC4 68 GPIO (5V) Note: 1. GPIO with 5V tolerance are indicated by (5V). silabs.com | Building a more connected world. Rev. 1.6 | 133 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions 6.5 QFN48 2.4 GHz and Sub-GHz Device Pinout Figure 6.5. QFN48 2.4 GHz and Sub-GHz Device Pinout The following table provides package pin connections and general descriptions of pin functionality. For detailed information on the supported features for each GPIO pin, see 6.7 GPIO Functionality Table or 6.8 Alternate Functionality Overview. Table 6.5. QFN48 2.4 GHz and Sub-GHz Device Pinout Pin Name Pin(s) Description Pin Name Pin(s) Description VSS 0 Ground PF0 1 GPIO (5V) PF1 2 GPIO (5V) PF2 3 GPIO (5V) PF3 4 GPIO (5V) PF4 5 GPIO (5V) PF5 6 GPIO (5V) PF6 7 GPIO (5V) PF7 8 GPIO (5V) RFVDD 9 Radio power supply HFXTAL_N 10 High Frequency Crystal input pin. HFXTAL_P 11 High Frequency Crystal output pin. silabs.com | Building a more connected world. Rev. 1.6 | 134 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Pin Name Pin(s) Description Pin Name Pin(s) Description SUBGRF_OP 13 Sub GHz Differential RF output, positive path. SUBGRF_IP 15 Sub GHz Differential RF input, positive path. RESETn 12 Reset input, active low. This pin is internally pulled up to AVDD. To apply an external reset source to this pin, it is required to only drive this pin low during reset, and let the internal pull-up ensure that reset is released. SUBGRF_ON 14 Sub GHz Differential RF output, negative path. SUBGRF_IN 16 Sub GHz Differential RF input, negative path. RFVSS 17 Radio Ground PAVSS 18 Power Amplifier (PA) voltage regulator VSS 2G4RF_ION 19 2.4 GHz Differential RF input/output, negative path. This pin should be externally grounded. 2G4RF_IOP 20 2.4 GHz Differential RF input/output, positive path. PAVDD 21 Power Amplifier (PA) voltage regulator VDD input PD13 22 GPIO PD14 23 GPIO PD15 24 GPIO PA0 25 GPIO PA1 26 GPIO PA2 27 GPIO PA3 28 GPIO PA4 29 GPIO PA5 30 GPIO (5V) PB11 31 GPIO PB12 32 GPIO PB13 33 GPIO AVDD 34 Analog power supply. PB14 35 GPIO PB15 36 GPIO VREGVSS 37 Voltage regulator VSS VREGSW 38 DCDC regulator switching node VREGVDD 39 Voltage regulator VDD input DECOUPLE 41 Decouple output for on-chip voltage regulator. An external decoupling capacitor is required at this pin. This pin should not be used to power any external circuits. DVDD 40 Digital power supply. IOVDD 42 Digital IO power supply. PC6 43 GPIO (5V) PC7 44 GPIO (5V) PC8 45 GPIO (5V) PC9 46 GPIO (5V) PC10 47 GPIO (5V) PC11 48 GPIO (5V) Note: 1. GPIO with 5V tolerance are indicated by (5V). silabs.com | Building a more connected world. Rev. 1.6 | 135 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions 6.6 QFN48 2.4 GHz Device Pinout Figure 6.6. QFN48 2.4 GHz Device Pinout The following table provides package pin connections and general descriptions of pin functionality. For detailed information on the supported features for each GPIO pin, see 6.7 GPIO Functionality Table or 6.8 Alternate Functionality Overview. Table 6.6. QFN48 2.4 GHz Device Pinout Pin Name Pin(s) Description Pin Name Pin(s) Description VSS 0 Ground PF0 1 GPIO (5V) PF1 2 GPIO (5V) PF2 3 GPIO (5V) PF3 4 GPIO (5V) PF4 5 GPIO (5V) PF5 6 GPIO (5V) PF6 7 GPIO (5V) PF7 8 GPIO (5V) RFVDD 9 Radio power supply HFXTAL_N 10 High Frequency Crystal input pin. HFXTAL_P 11 High Frequency Crystal output pin. silabs.com | Building a more connected world. Rev. 1.6 | 136 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Pin Name Pin(s) Description Pin Name Pin(s) Description NC 13 No Connect. PAVSS 15 Power Amplifier (PA) voltage regulator VSS RESETn 12 Reset input, active low. This pin is internally pulled up to AVDD. To apply an external reset source to this pin, it is required to only drive this pin low during reset, and let the internal pull-up ensure that reset is released. RFVSS 14 Radio Ground 2G4RF_ION 16 2.4 GHz Differential RF input/output, negative path. This pin should be externally grounded. 2G4RF_IOP 17 2.4 GHz Differential RF input/output, positive path. PAVDD 18 Power Amplifier (PA) voltage regulator VDD input PD10 19 GPIO (5V) PD11 20 GPIO (5V) PD12 21 GPIO (5V) PD13 22 GPIO PD14 23 GPIO PD15 24 GPIO PA0 25 GPIO PA1 26 GPIO PA2 27 GPIO PA3 28 GPIO PA4 29 GPIO PA5 30 GPIO (5V) PB11 31 GPIO PB12 32 GPIO PB13 33 GPIO AVDD 34 Analog power supply. PB14 35 GPIO PB15 36 GPIO VREGVSS 37 Voltage regulator VSS VREGSW 38 DCDC regulator switching node VREGVDD 39 Voltage regulator VDD input DECOUPLE 41 Decouple output for on-chip voltage regulator. An external decoupling capacitor is required at this pin. This pin should not be used to power any external circuits. DVDD 40 Digital power supply. IOVDD 42 Digital IO power supply. PC6 43 GPIO (5V) PC7 44 GPIO (5V) PC8 45 GPIO (5V) PC9 46 GPIO (5V) PC10 47 GPIO (5V) PC11 48 GPIO (5V) Note: 1. GPIO with 5V tolerance are indicated by (5V). silabs.com | Building a more connected world. Rev. 1.6 | 137 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions 6.7 GPIO Functionality Table A wide selection of alternate functionality is available for multiplexing to various pins. The following table shows the name of each GPIO pin, followed by the functionality available on that pin. Refer to 6.8 Alternate Functionality Overview for a list of GPIO locations available for each function. Table 6.7. GPIO Functionality Table GPIO Name Pin Alternate Functionality / Description Analog Timers TIM0_CC0 #0 TIM0_CC1 #31 TIM0_CC2 #30 TIM0_CDTI0 #29 TIM0_CDTI1 #28 TIM0_CDTI2 #27 PA0 BUSDY TIM1_CC0 #0 BUSCX TIM1_CC1 #31 ADC0_EXTN TIM1_CC2 #30 TIM1_CC3 #29 WTIM0_CC0 #0 LETIM0_OUT0 #0 LETIM0_OUT1 #31 PCNT0_S0IN #0 PCNT0_S1IN #31 silabs.com | Building a more connected world. Communication Radio Other US0_CTS #28 FRC_DCLK #0 CMU_CLK1 #0 US0_RTS #27 FRC_DOUT #31 PRS_CH6 #0 US1_TX #0 FRC_DFRAME #30 PRS_CH7 #10 US1_RX #31 MODEM_DCLK #0 PRS_CH8 #9 US1_CLK #30 MODEM_DIN #31 PRS_CH9 #8 US1_CS #29 MODEM_DOUT #30 ACMP0_O #0 US1_CTS #28 MODEM_ANT0 #29 ACMP1_O #0 US1_RTS #27 MODEM_ANT1 #28 LES_CH8 US0_TX #0 US0_RX #31 US0_CLK #30 US0_CS #29 LEU0_TX #0 LEU0_RX #31 I2C0_SDA #0 I2C0_SCL #31 Rev. 1.6 | 138 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers TIM0_CC0 #1 TIM0_CC1 #0 TIM0_CC2 #31 TIM0_CDTI0 #30 TIM0_CDTI1 #29 BUSCY PA1 BUSDX ADC0_EXTP VDAC0_EXT TIM0_CDTI2 #28 TIM1_CC0 #1 TIM1_CC1 #0 TIM1_CC2 #31 TIM1_CC3 #30 WTIM0_CC0 #1 LETIM0_OUT0 #1 LETIM0_OUT1 #0 PCNT0_S0IN #1 PCNT0_S1IN #0 VDAC0_OUT1ALT / OPA1_OUTALT #1 PA2 BUSDY BUSCX OPA0_P silabs.com | Building a more connected world. Communication Radio Other US0_CTS #29 FRC_DCLK #1 CMU_CLK0 #0 US0_RTS #28 FRC_DOUT #0 PRS_CH6 #1 US1_TX #1 FRC_DFRAME #31 PRS_CH7 #0 US1_RX #0 MODEM_DCLK #1 PRS_CH8 #10 US1_CLK #31 MODEM_DIN #0 PRS_CH9 #9 US1_CS #30 MODEM_DOUT #31 ACMP0_O #1 US1_CTS #29 MODEM_ANT0 #30 ACMP1_O #1 US1_RTS #28 MODEM_ANT1 #29 LES_CH9 US0_TX #1 US0_RX #0 US0_CLK #31 US0_CS #30 LEU0_TX #1 LEU0_RX #0 I2C0_SDA #1 I2C0_SCL #0 TIM0_CC0 #2 US0_TX #2 TIM0_CC1 #1 US0_RX #1 TIM0_CC2 #0 US0_CLK #0 TIM0_CDTI0 #31 US0_CS #31 TIM0_CDTI1 #30 US0_CTS #30 FRC_DCLK #2 TIM0_CDTI2 #29 US0_RTS #29 FRC_DOUT #1 TIM1_CC0 #2 US1_TX #2 FRC_DFRAME #0 TIM1_CC1 #1 US1_RX #1 MODEM_DCLK #2 TIM1_CC2 #0 US1_CLK #0 MODEM_DIN #1 TIM1_CC3 #31 US1_CS #31 MODEM_DOUT #0 WTIM0_CC0 #2 US1_CTS #30 MODEM_ANT0 #31 WTIM0_CC1 #0 US1_RTS #29 MODEM_ANT1 #30 LETIM0_OUT0 #2 LEU0_TX #2 LETIM0_OUT1 #1 LEU0_RX #1 PCNT0_S0IN #2 I2C0_SDA #2 PCNT0_S1IN #1 I2C0_SCL #1 PRS_CH6 #2 PRS_CH7 #1 PRS_CH8 #0 PRS_CH9 #10 ACMP0_O #2 ACMP1_O #2 LES_CH10 Rev. 1.6 | 139 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog PA3 Timers Communication Radio Other TIM0_CC0 #3 US0_TX #3 TIM0_CC1 #2 US0_RX #2 TIM0_CC2 #1 US0_CLK #1 TIM0_CDTI0 #0 US0_CS #0 TIM0_CDTI1 #31 US0_CTS #31 FRC_DCLK #3 PRS_CH6 #3 TIM0_CDTI2 #30 US0_RTS #30 FRC_DOUT #2 PRS_CH7 #2 BUSCY TIM1_CC0 #3 US1_TX #3 FRC_DFRAME #1 PRS_CH8 #1 BUSDX TIM1_CC1 #2 US1_RX #2 MODEM_DCLK #3 PRS_CH9 #0 VDAC0_OUT0 / OPA0_OUT TIM1_CC2 #1 US1_CLK #1 MODEM_DIN #2 ACMP0_O #3 TIM1_CC3 #0 US1_CS #0 MODEM_DOUT #1 ACMP1_O #3 WTIM0_CC0 #3 US1_CTS #31 MODEM_ANT0 #0 LES_CH11 WTIM0_CC1 #1 US1_RTS #30 MODEM_ANT1 #31 GPIO_EM4WU8 LETIM0_OUT0 #3 LEU0_TX #3 LETIM0_OUT1 #2 LEU0_RX #2 PCNT0_S0IN #3 I2C0_SDA #3 PCNT0_S1IN #2 I2C0_SCL #2 TIM0_CC0 #4 TIM0_CC1 #3 TIM0_CC2 #2 TIM0_CDTI0 #1 TIM0_CDTI1 #0 TIM0_CDTI2 #31 VDAC0_OUT1ALT / OPA1_OUTALT #2 PA4 BUSDY BUSCX OPA0_N TIM1_CC0 #4 TIM1_CC1 #3 TIM1_CC2 #2 TIM1_CC3 #1 WTIM0_CC0 #4 WTIM0_CC1 #2 WTIM0_CC2 #0 LETIM0_OUT0 #4 LETIM0_OUT1 #3 PCNT0_S0IN #4 PCNT0_S1IN #3 silabs.com | Building a more connected world. US0_TX #4 US0_RX #3 US0_CLK #2 US0_CS #1 US0_CTS #0 FRC_DCLK #4 US0_RTS #31 FRC_DOUT #3 US1_TX #4 FRC_DFRAME #2 US1_RX #3 MODEM_DCLK #4 US1_CLK #2 MODEM_DIN #3 US1_CS #1 MODEM_DOUT #2 US1_CTS #0 MODEM_ANT0 #1 US1_RTS #31 MODEM_ANT1 #0 PRS_CH6 #4 PRS_CH7 #3 PRS_CH8 #2 PRS_CH9 #1 ACMP0_O #4 ACMP1_O #4 LES_CH12 LEU0_TX #4 LEU0_RX #3 I2C0_SDA #4 I2C0_SCL #3 Rev. 1.6 | 140 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US0_TX #5 US0_RX #4 TIM0_CC0 #5 TIM0_CC1 #4 TIM0_CC2 #3 TIM0_CDTI0 #2 TIM0_CDTI1 #1 TIM0_CDTI2 #0 TIM1_CC0 #5 VDAC0_OUT0ALT / OPA0_OUTALT #0 PA5 BUSCY BUSDX TIM1_CC1 #4 TIM1_CC2 #3 TIM1_CC3 #2 WTIM0_CC0 #5 WTIM0_CC1 #3 WTIM0_CC2 #1 LETIM0_OUT0 #5 LETIM0_OUT1 #4 PCNT0_S0IN #5 PCNT0_S1IN #4 US0_CLK #3 US0_CS #2 US0_CTS #1 US0_RTS #0 US1_TX #5 US1_RX #4 FRC_DCLK #5 US1_CLK #3 FRC_DOUT #4 US1_CS #2 FRC_DFRAME #3 US1_CTS #1 MODEM_DCLK #5 US1_RTS #0 MODEM_DIN #4 US2_TX #0 MODEM_DOUT #3 US2_RX #31 MODEM_ANT0 #2 US2_CLK #30 MODEM_ANT1 #1 US2_CS #29 CMU_CLKI0 #4 PRS_CH6 #5 PRS_CH7 #4 PRS_CH8 #3 PRS_CH9 #2 ACMP0_O #5 ACMP1_O #5 LES_CH13 ETM_TCLK #1 US2_CTS #28 US2_RTS #27 LEU0_TX #5 LEU0_RX #4 I2C0_SDA #5 I2C0_SCL #4 WTIM0_CC0 #6 WTIM0_CC1 #4 PA6 BUSDY BUSCX WTIM0_CC2 #2 PCNT1_S0IN #0 PCNT1_S1IN #31 PCNT2_S0IN #0 PCNT2_S1IN #31 silabs.com | Building a more connected world. US2_TX #1 US2_RX #0 US2_CLK #31 US2_CS #30 LES_CH14 US2_CTS #29 ETM_TD0 #1 US2_RTS #28 I2C1_SDA #0 I2C1_SCL #31 Rev. 1.6 | 141 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers WTIM0_CC0 #7 WTIM0_CC1 #5 PA7 BUSCY BUSDX WTIM0_CC2 #3 PCNT1_S0IN #1 PCNT1_S1IN #0 PCNT2_S0IN #1 PCNT2_S1IN #0 PA8 PA9 Communication Radio Other US2_TX #2 US2_RX #1 US2_CLK #0 US2_CS #31 LES_CH15 US2_CTS #30 ETM_TD1 #1 US2_RTS #29 I2C1_SDA #1 I2C1_SCL #0 WTIM0_CC0 #8 US2_TX #3 WTIM0_CC1 #6 US2_RX #2 WTIM0_CC2 #4 US2_CLK #1 BUSACMP0Y WTIM0_CDTI0 #0 US2_CS #0 LES_ALTEX0 BUSACMP0X PCNT1_S0IN #2 US2_CTS #31 ETM_TD2 #1 PCNT1_S1IN #1 US2_RTS #30 PCNT2_S0IN #2 I2C1_SDA #2 PCNT2_S1IN #1 I2C1_SCL #1 WTIM0_CC0 #9 US2_TX #4 WTIM0_CC1 #7 US2_RX #3 WTIM0_CC2 #5 US2_CLK #2 BUSACMP0Y WTIM0_CDTI0 #1 US2_CS #1 LES_ALTEX1 BUSACMP0X PCNT1_S0IN #3 US2_CTS #0 ETM_TD3 #1 PCNT1_S1IN #2 US2_RTS #31 PCNT2_S0IN #3 I2C1_SDA #3 PCNT2_S1IN #2 I2C1_SCL #2 silabs.com | Building a more connected world. Rev. 1.6 | 142 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US2_TX #9 US2_RX #8 WTIM0_CC0 #10 WTIM0_CC1 #8 WTIM0_CC2 #6 PB6 BUSDY BUSCX WTIM0_CDTI0 #2 WTIM0_CDTI1 #0 PCNT1_S0IN #6 PCNT1_S1IN #5 PCNT2_S0IN #6 PCNT2_S1IN #5 US2_CLK #7 US2_CS #6 US2_CTS #5 US2_RTS #4 US3_TX #10 CMU_CLKI0 #3 US3_RX #9 ETM_TD1 #2 US3_CLK #8 US3_CS #7 US3_CTS #6 US3_RTS #5 I2C1_SDA #6 I2C1_SCL #5 US2_TX #10 US2_RX #9 WTIM0_CC0 #11 WTIM0_CC1 #9 WTIM0_CC2 #7 PB7 BUSCY BUSDX WTIM0_CDTI0 #3 WTIM0_CDTI1 #1 PCNT1_S0IN #7 PCNT1_S1IN #6 PCNT2_S0IN #7 PCNT2_S1IN #6 US2_CLK #8 US2_CS #7 US2_CTS #6 US2_RTS #5 US3_TX #11 US3_RX #10 ETM_TD2 #2 US3_CLK #9 US3_CS #8 US3_CTS #7 US3_RTS #6 I2C1_SDA #7 I2C1_SCL #6 silabs.com | Building a more connected world. Rev. 1.6 | 143 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US2_TX #11 US2_RX #10 PB8 WTIM0_CC0 #12 US2_CLK #9 WTIM0_CC1 #10 US2_CS #8 WTIM0_CC2 #8 US2_CTS #7 WTIM0_CDTI0 #4 US2_RTS #6 BUSDY WTIM0_CDTI1 #2 US3_TX #12 BUSCX WTIM0_CDTI2 #0 US3_RX #11 PCNT1_S0IN #8 US3_CLK #10 PCNT1_S1IN #7 US3_CS #9 PCNT2_S0IN #8 US3_CTS #8 PCNT2_S1IN #7 US3_RTS #7 ETM_TD3 #2 I2C1_SDA #8 I2C1_SCL #7 US2_TX #12 US2_RX #11 OPA2_OUTALT #0 PB9 BUSCY BUSDX WTIM0_CC0 #13 US2_CLK #10 WTIM0_CC1 #11 US2_CS #9 WTIM0_CC2 #9 US2_CTS #8 WTIM0_CDTI0 #5 US2_RTS #7 WTIM0_CDTI1 #3 US3_TX #13 WTIM0_CDTI2 #1 US3_RX #12 PCNT1_S0IN #9 US3_CLK #11 PCNT1_S1IN #8 US3_CS #10 PCNT2_S0IN #9 US3_CTS #9 PCNT2_S1IN #8 US3_RTS #8 I2C1_SDA #9 I2C1_SCL #8 silabs.com | Building a more connected world. Rev. 1.6 | 144 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US2_TX #13 US2_RX #12 OPA2_OUTALT #1 PB10 BUSDY BUSCX WTIM0_CC0 #14 US2_CLK #11 WTIM0_CC1 #12 US2_CS #10 WTIM0_CC2 #10 US2_CTS #9 WTIM0_CDTI0 #6 US2_RTS #8 WTIM0_CDTI1 #4 US3_TX #14 WTIM0_CDTI2 #2 US3_RX #13 PCNT1_S0IN #10 US3_CLK #12 PCNT1_S1IN #9 US3_CS #11 PCNT2_S0IN #10 US3_CTS #10 PCNT2_S1IN #9 US3_RTS #9 I2C1_SDA #10 I2C1_SCL #9 silabs.com | Building a more connected world. Rev. 1.6 | 145 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US0_TX #6 BUSCY PB11 BUSDX OPA2_P TIM0_CC0 #6 US0_RX #5 TIM0_CC1 #5 US0_CLK #4 TIM0_CC2 #4 US0_CS #3 TIM0_CDTI0 #3 US0_CTS #2 TIM0_CDTI1 #2 US0_RTS #1 TIM0_CDTI2 #1 US1_TX #6 TIM1_CC0 #6 US1_RX #5 FRC_DCLK #6 TIM1_CC1 #5 US1_CLK #4 FRC_DOUT #5 PRS_CH6 #6 TIM1_CC2 #4 US1_CS #3 FRC_DFRAME #4 PRS_CH7 #5 TIM1_CC3 #3 US1_CTS #2 MODEM_DCLK #6 PRS_CH8 #4 WTIM0_CC0 #15 US1_RTS #1 MODEM_DIN #5 PRS_CH9 #3 WTIM0_CC1 #13 US3_TX #15 MODEM_DOUT #4 ACMP0_O #6 WTIM0_CC2 #11 US3_RX #14 MODEM_ANT0 #3 ACMP1_O #6 WTIM0_CDTI0 #7 US3_CLK #13 MODEM_ANT1 #2 WTIM0_CDTI1 #5 US3_CS #12 WTIM0_CDTI2 #3 US3_CTS #11 LETIM0_OUT0 #6 US3_RTS #10 LETIM0_OUT1 #5 LEU0_TX #6 PCNT0_S0IN #6 LEU0_RX #5 PCNT0_S1IN #5 I2C0_SDA #6 I2C0_SCL #5 silabs.com | Building a more connected world. Rev. 1.6 | 146 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #7 TIM0_CC1 #6 TIM0_CC2 #5 TIM0_CDTI0 #4 TIM0_CDTI1 #3 TIM0_CDTI2 #2 TIM1_CC0 #7 TIM1_CC1 #6 TIM1_CC2 #5 PB12 BUSDY TIM1_CC3 #4 BUSCX WTIM0_CC0 #16 OPA2_OUT WTIM0_CC1 #14 WTIM0_CC2 #12 WTIM0_CDTI0 #8 WTIM0_CDTI1 #6 WTIM0_CDTI2 #4 WTIM1_CC0 #0 LETIM0_OUT0 #7 LETIM0_OUT1 #6 US0_TX #7 US0_RX #6 US0_CLK #5 US0_CS #4 US0_CTS #3 FRC_DCLK #7 US0_RTS #2 FRC_DOUT #6 PRS_CH6 #7 US1_TX #7 FRC_DFRAME #5 PRS_CH7 #6 US1_RX #6 MODEM_DCLK #7 PRS_CH8 #5 US1_CLK #5 MODEM_DIN #6 PRS_CH9 #4 US1_CS #4 MODEM_DOUT #5 ACMP0_O #7 US1_CTS #3 MODEM_ANT0 #4 ACMP1_O #7 US1_RTS #2 MODEM_ANT1 #3 LEU0_TX #7 LEU0_RX #6 I2C0_SDA #7 I2C0_SCL #6 PCNT0_S0IN #7 PCNT0_S1IN #6 silabs.com | Building a more connected world. Rev. 1.6 | 147 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #8 TIM0_CC1 #7 TIM0_CC2 #6 TIM0_CDTI0 #5 TIM0_CDTI1 #4 TIM0_CDTI2 #3 TIM1_CC0 #8 TIM1_CC1 #7 TIM1_CC2 #6 PB13 BUSCY TIM1_CC3 #5 BUSDX WTIM0_CC0 #17 OPA2_N WTIM0_CC1 #15 WTIM0_CC2 #13 WTIM0_CDTI0 #9 WTIM0_CDTI1 #7 WTIM0_CDTI2 #5 WTIM1_CC0 #1 LETIM0_OUT0 #8 LETIM0_OUT1 #7 US0_TX #8 US0_RX #7 US0_CLK #6 US0_CS #5 US0_CTS #4 FRC_DCLK #8 US0_RTS #3 FRC_DOUT #7 US1_TX #8 FRC_DFRAME #6 US1_RX #7 MODEM_DCLK #8 US1_CLK #6 MODEM_DIN #7 US1_CS #5 MODEM_DOUT #6 US1_CTS #4 MODEM_ANT0 #5 US1_RTS #3 MODEM_ANT1 #4 LEU0_TX #8 CMU_CLKI0 #0 PRS_CH6 #8 PRS_CH7 #7 PRS_CH8 #6 PRS_CH9 #5 ACMP0_O #8 ACMP1_O #8 DBG_SWO #1 GPIO_EM4WU9 LEU0_RX #7 I2C0_SDA #8 I2C0_SCL #7 PCNT0_S0IN #8 PCNT0_S1IN #7 silabs.com | Building a more connected world. Rev. 1.6 | 148 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #9 TIM0_CC1 #8 TIM0_CC2 #7 BUSDY PB14 BUSCX LFXTAL_N TIM0_CDTI0 #6 US0_TX #9 TIM0_CDTI1 #5 US0_RX #8 TIM0_CDTI2 #4 US0_CLK #7 TIM1_CC0 #9 US0_CS #6 TIM1_CC1 #8 US0_CTS #5 FRC_DCLK #9 TIM1_CC2 #7 US0_RTS #4 FRC_DOUT #8 TIM1_CC3 #6 US1_TX #9 FRC_DFRAME #7 WTIM0_CC0 #18 US1_RX #8 MODEM_DCLK #9 WTIM0_CC1 #16 US1_CLK #7 MODEM_DIN #8 WTIM0_CC2 #14 US1_CS #6 MODEM_DOUT #7 WTIM0_CDTI0 #10 US1_CTS #5 MODEM_ANT0 #6 WTIM0_CDTI1 #8 US1_RTS #4 MODEM_ANT1 #5 WTIM0_CDTI2 #6 LEU0_TX #9 WTIM1_CC0 #2 LEU0_RX #8 WTIM1_CC1 #0 I2C0_SDA #9 LETIM0_OUT0 #9 I2C0_SCL #8 CMU_CLK1 #1 PRS_CH6 #9 PRS_CH7 #8 PRS_CH8 #7 PRS_CH9 #6 ACMP0_O #9 ACMP1_O #9 LETIM0_OUT1 #8 PCNT0_S0IN #9 PCNT0_S1IN #8 silabs.com | Building a more connected world. Rev. 1.6 | 149 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #10 TIM0_CC1 #9 TIM0_CC2 #8 BUSCY PB15 BUSDX LFXTAL_P TIM0_CDTI0 #7 US0_TX #10 TIM0_CDTI1 #6 US0_RX #9 TIM0_CDTI2 #5 US0_CLK #8 TIM1_CC0 #10 US0_CS #7 TIM1_CC1 #9 US0_CTS #6 FRC_DCLK #10 TIM1_CC2 #8 US0_RTS #5 FRC_DOUT #9 TIM1_CC3 #7 US1_TX #10 FRC_DFRAME #8 WTIM0_CC0 #19 US1_RX #9 MODEM_DCLK #10 WTIM0_CC1 #17 US1_CLK #8 MODEM_DIN #9 WTIM0_CC2 #15 US1_CS #7 MODEM_DOUT #8 WTIM0_CDTI0 #11 US1_CTS #6 MODEM_ANT0 #7 WTIM0_CDTI1 #9 US1_RTS #5 MODEM_ANT1 #6 WTIM0_CDTI2 #7 LEU0_TX #10 WTIM1_CC0 #3 LEU0_RX #9 WTIM1_CC1 #1 I2C0_SDA #10 LETIM0_OUT0 #10 I2C0_SCL #9 CMU_CLK0 #1 PRS_CH6 #10 PRS_CH7 #9 PRS_CH8 #8 PRS_CH9 #7 ACMP0_O #10 ACMP1_O #10 LETIM0_OUT1 #9 PCNT0_S0IN #10 PCNT0_S1IN #9 WTIM0_CC0 #20 WTIM0_CC1 #18 WTIM0_CC2 #16 WTIM0_CDTI0 #12 WTIM0_CDTI1 #10 PC0 BUSBY BUSAX WTIM0_CDTI2 #8 WTIM1_CC0 #4 WTIM1_CC1 #2 WTIM1_CC2 #0 PCNT1_S0IN #13 PCNT1_S1IN #12 US3_TX #18 US3_RX #17 US3_CLK #16 US3_CS #15 US3_CTS #14 US3_RTS #13 I2C1_SDA #13 I2C1_SCL #12 PCNT2_S0IN #13 PCNT2_S1IN #12 silabs.com | Building a more connected world. Rev. 1.6 | 150 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other WTIM0_CC0 #21 WTIM0_CC1 #19 WTIM0_CC2 #17 WTIM0_CDTI0 #13 WTIM0_CDTI1 #11 PC1 BUSAY BUSBX WTIM0_CDTI2 #9 WTIM1_CC0 #5 WTIM1_CC1 #3 WTIM1_CC2 #1 PCNT1_S0IN #14 PCNT1_S1IN #13 US3_TX #19 US3_RX #18 US3_CLK #17 US3_CS #16 US3_CTS #15 US3_RTS #14 I2C1_SDA #14 I2C1_SCL #13 PCNT2_S0IN #14 PCNT2_S1IN #13 WTIM0_CC0 #22 WTIM0_CC1 #20 WTIM0_CC2 #18 PC2 WTIM0_CDTI0 #14 US3_TX #20 WTIM0_CDTI1 #12 US3_RX #19 WTIM0_CDTI2 #10 US3_CLK #18 BUSBY WTIM1_CC0 #6 US3_CS #17 BUSAX WTIM1_CC1 #4 US3_CTS #16 WTIM1_CC2 #2 US3_RTS #15 WTIM1_CC3 #0 I2C1_SDA #15 PCNT1_S0IN #15 I2C1_SCL #14 PCNT1_S1IN #14 PCNT2_S0IN #15 PCNT2_S1IN #14 silabs.com | Building a more connected world. Rev. 1.6 | 151 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other WTIM0_CC0 #23 WTIM0_CC1 #21 WTIM0_CC2 #19 PC3 WTIM0_CDTI0 #15 US3_TX #21 WTIM0_CDTI1 #13 US3_RX #20 WTIM0_CDTI2 #11 US3_CLK #19 BUSAY WTIM1_CC0 #7 US3_CS #18 BUSBX WTIM1_CC1 #5 US3_CTS #17 WTIM1_CC2 #3 US3_RTS #16 WTIM1_CC3 #1 I2C1_SDA #16 PCNT1_S0IN #16 I2C1_SCL #15 PCNT1_S1IN #15 PCNT2_S0IN #16 PCNT2_S1IN #15 WTIM0_CC0 #24 WTIM0_CC1 #22 WTIM0_CC2 #20 PC4 WTIM0_CDTI0 #16 US3_TX #22 WTIM0_CDTI1 #14 US3_RX #21 WTIM0_CDTI2 #12 US3_CLK #20 BUSBY WTIM1_CC0 #8 US3_CS #19 BUSAX WTIM1_CC1 #6 US3_CTS #18 WTIM1_CC2 #4 US3_RTS #17 WTIM1_CC3 #2 I2C1_SDA #17 PCNT1_S0IN #17 I2C1_SCL #16 PCNT1_S1IN #16 PCNT2_S0IN #17 PCNT2_S1IN #16 silabs.com | Building a more connected world. Rev. 1.6 | 152 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other WTIM0_CC0 #25 WTIM0_CC1 #23 WTIM0_CC2 #21 PC5 WTIM0_CDTI0 #17 US3_TX #23 WTIM0_CDTI1 #15 US3_RX #22 WTIM0_CDTI2 #13 US3_CLK #21 BUSAY WTIM1_CC0 #9 US3_CS #20 BUSBX WTIM1_CC1 #7 US3_CTS #19 WTIM1_CC2 #5 US3_RTS #18 WTIM1_CC3 #3 I2C1_SDA #18 PCNT1_S0IN #18 I2C1_SCL #17 PCNT1_S1IN #17 PCNT2_S0IN #18 PCNT2_S1IN #17 silabs.com | Building a more connected world. Rev. 1.6 | 153 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #11 TIM0_CC1 #10 TIM0_CC2 #9 TIM0_CDTI0 #8 PC6 TIM0_CDTI1 #7 US0_TX #11 TIM0_CDTI2 #6 US0_RX #10 TIM1_CC0 #11 US0_CLK #9 TIM1_CC1 #10 US0_CS #8 TIM1_CC2 #9 US0_CTS #7 FRC_DCLK #11 TIM1_CC3 #8 US0_RTS #6 FRC_DOUT #10 WTIM0_CC0 #26 US1_TX #11 FRC_DFRAME #9 BUSBY WTIM0_CC1 #24 US1_RX #10 MODEM_DCLK #11 BUSAX WTIM0_CC2 #22 US1_CLK #9 MODEM_DIN #10 WTIM0_CDTI0 #18 US1_CS #8 MODEM_DOUT #9 WTIM0_CDTI1 #16 US1_CTS #7 MODEM_ANT0 #8 WTIM0_CDTI2 #14 US1_RTS #6 MODEM_ANT1 #7 WTIM1_CC0 #10 LEU0_TX #11 WTIM1_CC1 #8 LEU0_RX #10 WTIM1_CC2 #6 I2C0_SDA #11 WTIM1_CC3 #4 I2C0_SCL #10 CMU_CLK0 #2 CMU_CLKI0 #2 PRS_CH0 #8 PRS_CH9 #11 PRS_CH10 #0 PRS_CH11 #5 ACMP0_O #11 ACMP1_O #11 ETM_TCLK #3 LETIM0_OUT0 #11 LETIM0_OUT1 #10 PCNT0_S0IN #11 PCNT0_S1IN #10 silabs.com | Building a more connected world. Rev. 1.6 | 154 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #12 TIM0_CC1 #11 TIM0_CC2 #10 TIM0_CDTI0 #9 PC7 TIM0_CDTI1 #8 US0_TX #12 TIM0_CDTI2 #7 US0_RX #11 TIM1_CC0 #12 US0_CLK #10 TIM1_CC1 #11 US0_CS #9 TIM1_CC2 #10 US0_CTS #8 FRC_DCLK #12 CMU_CLK1 #2 TIM1_CC3 #9 US0_RTS #7 FRC_DOUT #11 PRS_CH0 #9 WTIM0_CC0 #27 US1_TX #12 FRC_DFRAME #10 PRS_CH9 #12 BUSAY WTIM0_CC1 #25 US1_RX #11 MODEM_DCLK #12 PRS_CH10 #1 BUSBX WTIM0_CC2 #23 US1_CLK #10 MODEM_DIN #11 PRS_CH11 #0 WTIM0_CDTI0 #19 US1_CS #9 MODEM_DOUT #10 ACMP0_O #12 WTIM0_CDTI1 #17 US1_CTS #8 MODEM_ANT0 #9 ACMP1_O #12 WTIM0_CDTI2 #15 US1_RTS #7 MODEM_ANT1 #8 ETM_TD0 #3 WTIM1_CC0 #11 LEU0_TX #12 WTIM1_CC1 #9 LEU0_RX #11 WTIM1_CC2 #7 I2C0_SDA #12 WTIM1_CC3 #5 I2C0_SCL #11 LETIM0_OUT0 #12 LETIM0_OUT1 #11 PCNT0_S0IN #12 PCNT0_S1IN #11 silabs.com | Building a more connected world. Rev. 1.6 | 155 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #13 TIM0_CC1 #12 TIM0_CC2 #11 TIM0_CDTI0 #10 PC8 TIM0_CDTI1 #9 US0_TX #13 TIM0_CDTI2 #8 US0_RX #12 TIM1_CC0 #13 US0_CLK #11 TIM1_CC1 #12 US0_CS #10 TIM1_CC2 #11 US0_CTS #9 FRC_DCLK #13 TIM1_CC3 #10 US0_RTS #8 FRC_DOUT #12 WTIM0_CC0 #28 US1_TX #13 FRC_DFRAME #11 BUSBY WTIM0_CC1 #26 US1_RX #12 MODEM_DCLK #13 BUSAX WTIM0_CC2 #24 US1_CLK #11 MODEM_DIN #12 WTIM0_CDTI0 #20 US1_CS #10 MODEM_DOUT #11 WTIM0_CDTI1 #18 US1_CTS #9 MODEM_ANT0 #10 WTIM0_CDTI2 #16 US1_RTS #8 MODEM_ANT1 #9 WTIM1_CC0 #12 LEU0_TX #13 WTIM1_CC1 #10 LEU0_RX #12 WTIM1_CC2 #8 I2C0_SDA #13 WTIM1_CC3 #6 I2C0_SCL #12 PRS_CH0 #10 PRS_CH9 #13 PRS_CH10 #2 PRS_CH11 #1 ACMP0_O #13 ACMP1_O #13 ETM_TD1 #3 LETIM0_OUT0 #13 LETIM0_OUT1 #12 PCNT0_S0IN #13 PCNT0_S1IN #12 silabs.com | Building a more connected world. Rev. 1.6 | 156 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #14 TIM0_CC1 #13 TIM0_CC2 #12 TIM0_CDTI0 #11 PC9 TIM0_CDTI1 #10 US0_TX #14 TIM0_CDTI2 #9 US0_RX #13 TIM1_CC0 #14 US0_CLK #12 TIM1_CC1 #13 US0_CS #11 TIM1_CC2 #12 US0_CTS #10 FRC_DCLK #14 TIM1_CC3 #11 US0_RTS #9 FRC_DOUT #13 WTIM0_CC0 #29 US1_TX #14 FRC_DFRAME #12 BUSAY WTIM0_CC1 #27 US1_RX #13 MODEM_DCLK #14 BUSBX WTIM0_CC2 #25 US1_CLK #12 MODEM_DIN #13 WTIM0_CDTI0 #21 US1_CS #11 MODEM_DOUT #12 WTIM0_CDTI1 #19 US1_CTS #10 MODEM_ANT0 #11 WTIM0_CDTI2 #17 US1_RTS #9 MODEM_ANT1 #10 WTIM1_CC0 #13 LEU0_TX #14 WTIM1_CC1 #11 LEU0_RX #13 WTIM1_CC2 #9 I2C0_SDA #14 WTIM1_CC3 #7 I2C0_SCL #13 PRS_CH0 #11 PRS_CH9 #14 PRS_CH10 #3 PRS_CH11 #2 ACMP0_O #14 ACMP1_O #14 ETM_TD2 #3 LETIM0_OUT0 #14 LETIM0_OUT1 #13 PCNT0_S0IN #14 PCNT0_S1IN #13 silabs.com | Building a more connected world. Rev. 1.6 | 157 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #15 TIM0_CC1 #14 TIM0_CC2 #13 TIM0_CDTI0 #12 PC10 TIM0_CDTI1 #11 US0_TX #15 TIM0_CDTI2 #10 US0_RX #14 TIM1_CC0 #15 US0_CLK #13 TIM1_CC1 #14 US0_CS #12 TIM1_CC2 #13 US0_CTS #11 TIM1_CC3 #12 US0_RTS #10 FRC_DCLK #15 WTIM0_CC0 #30 US1_TX #15 FRC_DOUT #14 WTIM0_CC1 #28 US1_RX #14 FRC_DFRAME #13 BUSBY WTIM0_CC2 #26 US1_CLK #13 MODEM_DCLK #15 BUSAX WTIM0_CDTI0 #22 US1_CS #12 MODEM_DIN #14 WTIM0_CDTI1 #20 US1_CTS #11 MODEM_DOUT #13 WTIM0_CDTI2 #18 US1_RTS #10 MODEM_ANT0 #12 WTIM1_CC0 #14 LEU0_TX #15 MODEM_ANT1 #11 WTIM1_CC1 #12 LEU0_RX #14 WTIM1_CC2 #10 I2C0_SDA #15 WTIM1_CC3 #8 I2C0_SCL #14 LETIM0_OUT0 #15 I2C1_SDA #19 LETIM0_OUT1 #14 I2C1_SCL #18 CMU_CLK1 #3 PRS_CH0 #12 PRS_CH9 #15 PRS_CH10 #4 PRS_CH11 #3 ACMP0_O #15 ACMP1_O #15 ETM_TD3 #3 GPIO_EM4WU12 PCNT0_S0IN #15 PCNT0_S1IN #14 PCNT2_S0IN #19 PCNT2_S1IN #18 silabs.com | Building a more connected world. Rev. 1.6 | 158 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #16 TIM0_CC1 #15 TIM0_CC2 #14 TIM0_CDTI0 #13 PC11 TIM0_CDTI1 #12 US0_TX #16 TIM0_CDTI2 #11 US0_RX #15 TIM1_CC0 #16 US0_CLK #14 TIM1_CC1 #15 US0_CS #13 TIM1_CC2 #14 US0_CTS #12 TIM1_CC3 #13 US0_RTS #11 FRC_DCLK #16 CMU_CLK0 #3 WTIM0_CC0 #31 US1_TX #16 FRC_DOUT #15 PRS_CH0 #13 WTIM0_CC1 #29 US1_RX #15 FRC_DFRAME #14 PRS_CH9 #16 BUSAY WTIM0_CC2 #27 US1_CLK #14 MODEM_DCLK #16 PRS_CH10 #5 BUSBX WTIM0_CDTI0 #23 US1_CS #13 MODEM_DIN #15 PRS_CH11 #4 WTIM0_CDTI1 #21 US1_CTS #12 MODEM_DOUT #14 ACMP0_O #16 WTIM0_CDTI2 #19 US1_RTS #11 MODEM_ANT0 #13 ACMP1_O #16 WTIM1_CC0 #15 LEU0_TX #16 MODEM_ANT1 #12 DBG_SWO #3 WTIM1_CC1 #13 LEU0_RX #15 WTIM1_CC2 #11 I2C0_SDA #16 WTIM1_CC3 #9 I2C0_SCL #15 LETIM0_OUT0 #16 I2C1_SDA #20 LETIM0_OUT1 #15 I2C1_SCL #19 PCNT0_S0IN #16 PCNT0_S1IN #15 PCNT2_S0IN #20 PCNT2_S1IN #19 WTIM0_CC1 #30 WTIM0_CC2 #28 WTIM0_CDTI0 #24 PD8 BUSDY BUSCX WTIM0_CDTI1 #22 WTIM0_CDTI2 #20 WTIM1_CC0 #16 WTIM1_CC1 #14 WTIM1_CC2 #12 US3_TX #0 US3_RX #31 US3_CLK #30 US3_CS #29 LES_CH0 US3_CTS #28 US3_RTS #27 WTIM1_CC3 #10 silabs.com | Building a more connected world. Rev. 1.6 | 159 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers TIM0_CC0 #17 TIM0_CC1 #16 TIM0_CC2 #15 TIM0_CDTI0 #14 TIM0_CDTI1 #13 TIM0_CDTI2 #12 TIM1_CC0 #17 TIM1_CC1 #16 TIM1_CC2 #15 TIM1_CC3 #14 PD9 BUSCY BUSDX WTIM0_CC1 #31 WTIM0_CC2 #29 WTIM0_CDTI0 #25 WTIM0_CDTI1 #23 WTIM0_CDTI2 #21 WTIM1_CC0 #17 WTIM1_CC1 #15 WTIM1_CC2 #13 WTIM1_CC3 #11 LETIM0_OUT0 #17 LETIM0_OUT1 #16 PCNT0_S0IN #17 PCNT0_S1IN #16 silabs.com | Building a more connected world. Communication Radio Other US1_RX #16 FRC_DCLK #17 CMU_CLK0 #4 US1_CLK #15 FRC_DOUT #16 PRS_CH3 #8 US1_CS #14 FRC_DFRAME #15 PRS_CH4 #0 US1_CTS #13 MODEM_DCLK #17 PRS_CH5 #6 US1_RTS #12 MODEM_DIN #16 PRS_CH6 #11 US3_TX #1 MODEM_DOUT #15 ACMP0_O #17 US3_RX #0 MODEM_ANT0 #14 ACMP1_O #17 US3_CLK #31 MODEM_ANT1 #13 LES_CH1 US0_TX #17 US0_RX #16 US0_CLK #15 US0_CS #14 US0_CTS #13 US0_RTS #12 US1_TX #17 US3_CS #30 US3_CTS #29 US3_RTS #28 LEU0_TX #17 LEU0_RX #16 I2C0_SDA #17 I2C0_SCL #16 Rev. 1.6 | 160 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog PD10 Radio Other US1_RX #17 FRC_DCLK #18 CMU_CLK1 #4 TIM1_CC2 #16 US1_CLK #16 FRC_DOUT #17 PRS_CH3 #9 TIM1_CC3 #15 US1_CS #15 FRC_DFRAME #16 PRS_CH4 #1 BUSDY WTIM0_CC2 #30 US1_CTS #14 MODEM_DCLK #18 PRS_CH5 #0 BUSCX WTIM0_CDTI0 #26 US1_RTS #13 MODEM_DIN #17 PRS_CH6 #12 WTIM0_CDTI1 #24 US3_TX #2 MODEM_DOUT #16 ACMP0_O #18 WTIM0_CDTI2 #22 US3_RX #1 MODEM_ANT0 #15 ACMP1_O #18 WTIM1_CC0 #18 US3_CLK #0 MODEM_ANT1 #14 LES_CH2 WTIM1_CC1 #16 US3_CS #31 WTIM1_CC2 #14 US3_CTS #30 WTIM1_CC3 #12 US3_RTS #29 LETIM0_OUT0 #18 LEU0_TX #18 LETIM0_OUT1 #17 LEU0_RX #17 PCNT0_S0IN #18 I2C0_SDA #18 PCNT0_S1IN #17 I2C0_SCL #17 silabs.com | Building a more connected world. Timers Communication TIM0_CC0 #18 US0_TX #18 TIM0_CC1 #17 US0_RX #17 TIM0_CC2 #16 US0_CLK #16 TIM0_CDTI0 #15 US0_CS #15 TIM0_CDTI1 #14 US0_CTS #14 TIM0_CDTI2 #13 US0_RTS #13 TIM1_CC0 #18 US1_TX #18 TIM1_CC1 #17 Rev. 1.6 | 161 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog PD11 Timers Communication TIM0_CC0 #19 US0_TX #19 TIM0_CC1 #18 US0_RX #18 TIM0_CC2 #17 US0_CLK #17 TIM0_CDTI0 #16 US0_CS #16 TIM0_CDTI1 #15 US0_CTS #15 TIM0_CDTI2 #14 US0_RTS #14 TIM1_CC0 #19 US1_TX #19 TIM1_CC1 #18 US1_RX #18 FRC_DCLK #19 TIM1_CC2 #17 US1_CLK #17 FRC_DOUT #18 TIM1_CC3 #16 US1_CS #16 FRC_DFRAME #17 BUSCY WTIM0_CC2 #31 US1_CTS #15 MODEM_DCLK #19 BUSDX WTIM0_CDTI0 #27 US1_RTS #14 MODEM_DIN #18 WTIM0_CDTI1 #25 US3_TX #3 MODEM_DOUT #17 WTIM0_CDTI2 #23 US3_RX #2 MODEM_ANT0 #16 WTIM1_CC0 #19 US3_CLK #1 MODEM_ANT1 #15 WTIM1_CC1 #17 US3_CS #0 WTIM1_CC2 #15 US3_CTS #31 WTIM1_CC3 #13 US3_RTS #30 LETIM0_OUT0 #19 LEU0_TX #19 LETIM0_OUT1 #18 LEU0_RX #18 PCNT0_S0IN #19 I2C0_SDA #19 PCNT0_S1IN #18 I2C0_SCL #18 silabs.com | Building a more connected world. Radio Other PRS_CH3 #10 PRS_CH4 #2 PRS_CH5 #1 PRS_CH6 #13 ACMP0_O #19 ACMP1_O #19 LES_CH3 Rev. 1.6 | 162 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers TIM0_CC0 #20 TIM0_CC1 #19 TIM0_CC2 #18 TIM0_CDTI0 #17 TIM0_CDTI1 #16 TIM0_CDTI2 #15 TIM1_CC0 #20 TIM1_CC1 #19 TIM1_CC2 #18 VDAC0_OUT1ALT / OPA1_OUTALT #0 PD12 BUSDY BUSCX TIM1_CC3 #17 WTIM0_CDTI0 #28 WTIM0_CDTI1 #26 WTIM0_CDTI2 #24 WTIM1_CC0 #20 WTIM1_CC1 #18 WTIM1_CC2 #16 WTIM1_CC3 #14 LETIM0_OUT0 #20 LETIM0_OUT1 #19 PCNT0_S0IN #20 PCNT0_S1IN #19 silabs.com | Building a more connected world. Communication Radio Other US0_TX #20 US0_RX #19 US0_CLK #18 US0_CS #17 US0_CTS #16 US0_RTS #15 US1_TX #20 US1_RX #19 FRC_DCLK #20 US1_CLK #18 FRC_DOUT #19 US1_CS #17 FRC_DFRAME #18 US1_CTS #16 MODEM_DCLK #20 US1_RTS #15 MODEM_DIN #19 US3_TX #4 MODEM_DOUT #18 US3_RX #3 MODEM_ANT0 #17 US3_CLK #2 MODEM_ANT1 #16 PRS_CH3 #11 PRS_CH4 #3 PRS_CH5 #2 PRS_CH6 #14 ACMP0_O #20 ACMP1_O #20 LES_CH4 US3_CS #1 US3_CTS #0 US3_RTS #31 LEU0_TX #20 LEU0_RX #19 I2C0_SDA #20 I2C0_SCL #19 Rev. 1.6 | 163 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers TIM0_CC0 #21 TIM0_CC1 #20 TIM0_CC2 #19 TIM0_CDTI0 #18 TIM0_CDTI1 #17 TIM0_CDTI2 #16 TIM1_CC0 #21 TIM1_CC1 #20 VDAC0_OUT0ALT / OPA0_OUTALT #1 PD13 BUSCY BUSDX OPA1_P TIM1_CC2 #19 TIM1_CC3 #18 WTIM0_CDTI0 #29 WTIM0_CDTI1 #27 WTIM0_CDTI2 #25 WTIM1_CC0 #21 WTIM1_CC1 #19 WTIM1_CC2 #17 WTIM1_CC3 #15 LETIM0_OUT0 #21 LETIM0_OUT1 #20 PCNT0_S0IN #21 PCNT0_S1IN #20 silabs.com | Building a more connected world. Communication Radio Other US0_TX #21 US0_RX #20 US0_CLK #19 US0_CS #18 US0_CTS #17 US0_RTS #16 US1_TX #21 US1_RX #20 FRC_DCLK #21 US1_CLK #19 FRC_DOUT #20 US1_CS #18 FRC_DFRAME #19 US1_CTS #17 MODEM_DCLK #21 US1_RTS #16 MODEM_DIN #20 US3_TX #5 MODEM_DOUT #19 US3_RX #4 MODEM_ANT0 #18 US3_CLK #3 MODEM_ANT1 #17 PRS_CH3 #12 PRS_CH4 #4 PRS_CH5 #3 PRS_CH6 #15 ACMP0_O #21 ACMP1_O #21 LES_CH5 US3_CS #2 US3_CTS #1 US3_RTS #0 LEU0_TX #21 LEU0_RX #20 I2C0_SDA #21 I2C0_SCL #20 Rev. 1.6 | 164 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers TIM0_CC0 #22 TIM0_CC1 #21 TIM0_CC2 #20 TIM0_CDTI0 #19 TIM0_CDTI1 #18 TIM0_CDTI2 #17 TIM1_CC0 #22 TIM1_CC1 #21 TIM1_CC2 #20 BUSDY PD14 BUSCX VDAC0_OUT1 / OPA1_OUT TIM1_CC3 #19 WTIM0_CDTI0 #30 WTIM0_CDTI1 #28 WTIM0_CDTI2 #26 WTIM1_CC0 #22 WTIM1_CC1 #20 WTIM1_CC2 #18 WTIM1_CC3 #16 LETIM0_OUT0 #22 LETIM0_OUT1 #21 PCNT0_S0IN #22 PCNT0_S1IN #21 silabs.com | Building a more connected world. Communication Radio Other US0_TX #22 US0_RX #21 US0_CLK #20 US0_CS #19 US0_CTS #18 US0_RTS #17 US1_TX #22 US1_RX #21 FRC_DCLK #22 US1_CLK #20 FRC_DOUT #21 US1_CS #19 FRC_DFRAME #20 US1_CTS #18 MODEM_DCLK #22 US1_RTS #17 MODEM_DIN #21 US3_TX #6 MODEM_DOUT #20 US3_RX #5 MODEM_ANT0 #19 US3_CLK #4 MODEM_ANT1 #18 US3_CS #3 CMU_CLK0 #5 PRS_CH3 #13 PRS_CH4 #5 PRS_CH5 #4 PRS_CH6 #16 ACMP0_O #22 ACMP1_O #22 LES_CH6 GPIO_EM4WU4 US3_CTS #2 US3_RTS #1 LEU0_TX #22 LEU0_RX #21 I2C0_SDA #22 I2C0_SCL #21 Rev. 1.6 | 165 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers TIM0_CC0 #23 TIM0_CC1 #22 TIM0_CC2 #21 TIM0_CDTI0 #20 TIM0_CDTI1 #19 TIM0_CDTI2 #18 TIM1_CC0 #23 TIM1_CC1 #22 VDAC0_OUT0ALT / OPA0_OUTALT #2 PD15 BUSCY BUSDX OPA1_N TIM1_CC2 #21 TIM1_CC3 #20 WTIM0_CDTI0 #31 WTIM0_CDTI1 #29 WTIM0_CDTI2 #27 WTIM1_CC0 #23 WTIM1_CC1 #21 WTIM1_CC2 #19 WTIM1_CC3 #17 LETIM0_OUT0 #23 LETIM0_OUT1 #22 PCNT0_S0IN #23 PCNT0_S1IN #22 silabs.com | Building a more connected world. Communication Radio Other US0_TX #23 US0_RX #22 US0_CLK #21 US0_CS #20 US0_CTS #19 US0_RTS #18 US1_TX #23 US1_RX #22 FRC_DCLK #23 US1_CLK #21 FRC_DOUT #22 US1_CS #20 FRC_DFRAME #21 US1_CTS #19 MODEM_DCLK #23 US1_RTS #18 MODEM_DIN #22 US3_TX #7 MODEM_DOUT #21 US3_RX #6 MODEM_ANT0 #20 US3_CLK #5 MODEM_ANT1 #19 US3_CS #4 CMU_CLK1 #5 PRS_CH3 #14 PRS_CH4 #6 PRS_CH5 #5 PRS_CH6 #17 ACMP0_O #23 ACMP1_O #23 LES_CH7 DBG_SWO #2 US3_CTS #3 US3_RTS #2 LEU0_TX #23 LEU0_RX #22 I2C0_SDA #23 I2C0_SCL #22 Rev. 1.6 | 166 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US0_TX #24 PF0 TIM0_CC0 #24 US0_RX #23 TIM0_CC1 #23 US0_CLK #22 TIM0_CC2 #22 US0_CS #21 TIM0_CDTI0 #21 US0_CTS #20 TIM0_CDTI1 #20 US0_RTS #19 TIM0_CDTI2 #19 US1_TX #24 TIM1_CC0 #24 US1_RX #23 FRC_DCLK #24 PRS_CH0 #0 TIM1_CC1 #23 US1_CLK #22 FRC_DOUT #23 PRS_CH1 #7 TIM1_CC2 #22 US1_CS #21 FRC_DFRAME #22 PRS_CH2 #6 BUSBY TIM1_CC3 #21 US1_CTS #20 MODEM_DCLK #24 PRS_CH3 #5 BUSAX WTIM0_CDTI1 #30 US1_RTS #19 MODEM_DIN #23 ACMP0_O #24 WTIM0_CDTI2 #28 US2_TX #14 MODEM_DOUT #22 ACMP1_O #24 WTIM1_CC0 #24 US2_RX #13 MODEM_ANT0 #21 DBG_SWCLKTCK WTIM1_CC1 #22 US2_CLK #12 MODEM_ANT1 #20 BOOT_TX WTIM1_CC2 #20 US2_CS #11 WTIM1_CC3 #18 US2_CTS #10 LETIM0_OUT0 #24 US2_RTS #9 LETIM0_OUT1 #23 LEU0_TX #24 PCNT0_S0IN #24 LEU0_RX #23 PCNT0_S1IN #23 I2C0_SDA #24 I2C0_SCL #23 silabs.com | Building a more connected world. Rev. 1.6 | 167 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US0_TX #25 PF1 TIM0_CC0 #25 US0_RX #24 TIM0_CC1 #24 US0_CLK #23 TIM0_CC2 #23 US0_CS #22 TIM0_CDTI0 #22 US0_CTS #21 TIM0_CDTI1 #21 US0_RTS #20 TIM0_CDTI2 #20 US1_TX #25 TIM1_CC0 #25 US1_RX #24 FRC_DCLK #25 PRS_CH0 #1 TIM1_CC1 #24 US1_CLK #23 FRC_DOUT #24 PRS_CH1 #0 TIM1_CC2 #23 US1_CS #22 FRC_DFRAME #23 PRS_CH2 #7 BUSAY TIM1_CC3 #22 US1_CTS #21 MODEM_DCLK #25 PRS_CH3 #6 BUSBX WTIM0_CDTI1 #31 US1_RTS #20 MODEM_DIN #24 ACMP0_O #25 WTIM0_CDTI2 #29 US2_TX #15 MODEM_DOUT #23 ACMP1_O #25 WTIM1_CC0 #25 US2_RX #14 MODEM_ANT0 #22 DBG_SWDIOTMS WTIM1_CC1 #23 US2_CLK #13 MODEM_ANT1 #21 BOOT_RX WTIM1_CC2 #21 US2_CS #12 WTIM1_CC3 #19 US2_CTS #11 LETIM0_OUT0 #25 US2_RTS #10 LETIM0_OUT1 #24 LEU0_TX #25 PCNT0_S0IN #25 LEU0_RX #24 PCNT0_S1IN #24 I2C0_SDA #25 I2C0_SCL #24 silabs.com | Building a more connected world. Rev. 1.6 | 168 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other TIM0_CC0 #26 TIM0_CC1 #25 TIM0_CC2 #24 TIM0_CDTI0 #23 TIM0_CDTI1 #22 TIM0_CDTI2 #21 TIM1_CC0 #26 TIM1_CC1 #25 PF2 BUSBY BUSAX TIM1_CC2 #24 TIM1_CC3 #23 WTIM0_CDTI2 #30 WTIM1_CC0 #26 WTIM1_CC1 #24 WTIM1_CC2 #22 WTIM1_CC3 #20 LETIM0_OUT0 #26 LETIM0_OUT1 #25 PCNT0_S0IN #26 US0_TX #26 US0_RX #25 US0_CLK #24 CMU_CLK0 #6 US0_CS #23 US0_CTS #22 FRC_DCLK #26 PRS_CH0 #2 US0_RTS #21 FRC_DOUT #25 PRS_CH1 #1 US1_TX #26 FRC_DFRAME #24 PRS_CH2 #0 US1_RX #25 MODEM_DCLK #26 PRS_CH3 #7 US1_CLK #24 MODEM_DIN #25 ACMP0_O #26 US1_CS #23 MODEM_DOUT #24 ACMP1_O #26 US1_CTS #22 MODEM_ANT0 #23 DBG_TDO US1_RTS #21 MODEM_ANT1 #22 DBG_SWO #0 LEU0_TX #26 GPIO_EM4WU0 LEU0_RX #25 I2C0_SDA #26 I2C0_SCL #25 PCNT0_S1IN #25 silabs.com | Building a more connected world. Rev. 1.6 | 169 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US1_RX #26 FRC_DCLK #27 CMU_CLK1 #6 US1_CLK #25 FRC_DOUT #26 PRS_CH0 #3 US1_CS #24 FRC_DFRAME #25 PRS_CH1 #2 US1_CTS #23 MODEM_DCLK #27 PRS_CH2 #1 US1_RTS #22 MODEM_DIN #26 PRS_CH3 #0 US2_TX #16 MODEM_DOUT #25 ACMP0_O #27 US2_RX #15 MODEM_ANT0 #24 ACMP1_O #27 US2_CLK #14 MODEM_ANT1 #23 DBG_TDI US0_TX #27 TIM0_CC0 #27 TIM0_CC1 #26 TIM0_CC2 #25 TIM0_CDTI0 #24 TIM0_CDTI1 #23 TIM0_CDTI2 #22 TIM1_CC0 #27 TIM1_CC1 #26 PF3 BUSAY BUSBX TIM1_CC2 #25 TIM1_CC3 #24 WTIM0_CDTI2 #31 WTIM1_CC0 #27 WTIM1_CC1 #25 WTIM1_CC2 #23 WTIM1_CC3 #21 LETIM0_OUT0 #27 LETIM0_OUT1 #26 PCNT0_S0IN #27 PCNT0_S1IN #26 US0_RX #26 US0_CLK #25 US0_CS #24 US0_CTS #23 US0_RTS #22 US1_TX #27 US2_CS #13 US2_CTS #12 US2_RTS #11 LEU0_TX #27 LEU0_RX #26 I2C0_SDA #27 I2C0_SCL #26 silabs.com | Building a more connected world. Rev. 1.6 | 170 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US0_TX #28 US0_RX #27 PF4 TIM0_CC0 #28 US0_CLK #26 TIM0_CC1 #27 US0_CS #25 TIM0_CC2 #26 US0_CTS #24 TIM0_CDTI0 #25 US0_RTS #23 TIM0_CDTI1 #24 US1_TX #28 TIM0_CDTI2 #23 US1_RX #27 FRC_DCLK #28 TIM1_CC0 #28 US1_CLK #26 FRC_DOUT #27 PRS_CH0 #4 TIM1_CC1 #27 US1_CS #25 FRC_DFRAME #26 PRS_CH1 #3 BUSBY TIM1_CC2 #26 US1_CTS #24 MODEM_DCLK #28 PRS_CH2 #2 BUSAX TIM1_CC3 #25 US1_RTS #23 MODEM_DIN #27 PRS_CH3 #1 WTIM1_CC0 #28 US2_TX #17 MODEM_DOUT #26 ACMP0_O #28 WTIM1_CC1 #26 US2_RX #16 MODEM_ANT0 #25 ACMP1_O #28 WTIM1_CC2 #24 US2_CLK #15 MODEM_ANT1 #24 WTIM1_CC3 #22 US2_CS #14 LETIM0_OUT0 #28 US2_CTS #13 LETIM0_OUT1 #27 US2_RTS #12 PCNT0_S0IN #28 LEU0_TX #28 PCNT0_S1IN #27 LEU0_RX #27 I2C0_SDA #28 I2C0_SCL #27 silabs.com | Building a more connected world. Rev. 1.6 | 171 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US0_TX #29 US0_RX #28 PF5 TIM0_CC0 #29 US0_CLK #27 TIM0_CC1 #28 US0_CS #26 TIM0_CC2 #27 US0_CTS #25 TIM0_CDTI0 #26 US0_RTS #24 TIM0_CDTI1 #25 US1_TX #29 TIM0_CDTI2 #24 US1_RX #28 FRC_DCLK #29 TIM1_CC0 #29 US1_CLK #27 FRC_DOUT #28 PRS_CH0 #5 TIM1_CC1 #28 US1_CS #26 FRC_DFRAME #27 PRS_CH1 #4 BUSAY TIM1_CC2 #27 US1_CTS #25 MODEM_DCLK #29 PRS_CH2 #3 BUSBX TIM1_CC3 #26 US1_RTS #24 MODEM_DIN #28 PRS_CH3 #2 WTIM1_CC0 #29 US2_TX #18 MODEM_DOUT #27 ACMP0_O #29 WTIM1_CC1 #27 US2_RX #17 MODEM_ANT0 #26 ACMP1_O #29 WTIM1_CC2 #25 US2_CLK #16 MODEM_ANT1 #25 WTIM1_CC3 #23 US2_CS #15 LETIM0_OUT0 #29 US2_CTS #14 LETIM0_OUT1 #28 US2_RTS #13 PCNT0_S0IN #29 LEU0_TX #29 PCNT0_S1IN #28 LEU0_RX #28 I2C0_SDA #29 I2C0_SCL #28 silabs.com | Building a more connected world. Rev. 1.6 | 172 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US0_TX #30 PF6 TIM0_CC0 #30 US0_RX #29 TIM0_CC1 #29 US0_CLK #28 TIM0_CC2 #28 US0_CS #27 TIM0_CDTI0 #27 US0_CTS #26 TIM0_CDTI1 #26 US0_RTS #25 TIM0_CDTI2 #25 US1_TX #30 TIM1_CC0 #30 US1_RX #29 FRC_DCLK #30 TIM1_CC1 #29 US1_CLK #28 FRC_DOUT #29 TIM1_CC2 #28 US1_CS #27 FRC_DFRAME #28 BUSBY TIM1_CC3 #27 US1_CTS #26 MODEM_DCLK #30 BUSAX WTIM1_CC0 #30 US1_RTS #25 MODEM_DIN #29 WTIM1_CC1 #28 US2_TX #19 MODEM_DOUT #28 WTIM1_CC2 #26 US2_RX #18 MODEM_ANT0 #27 WTIM1_CC3 #24 US2_CLK #17 MODEM_ANT1 #26 LETIM0_OUT0 #30 US2_CS #16 LETIM0_OUT1 #29 US2_CTS #15 PCNT0_S0IN #30 US2_RTS #14 PCNT0_S1IN #29 LEU0_TX #30 PCNT1_S0IN #19 LEU0_RX #29 PCNT1_S1IN #18 I2C0_SDA #30 CMU_CLK1 #7 PRS_CH0 #6 PRS_CH1 #5 PRS_CH2 #4 PRS_CH3 #3 ACMP0_O #30 ACMP1_O #30 I2C0_SCL #29 silabs.com | Building a more connected world. Rev. 1.6 | 173 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US0_TX #31 PF7 TIM0_CC0 #31 US0_RX #30 TIM0_CC1 #30 US0_CLK #29 TIM0_CC2 #29 US0_CS #28 TIM0_CDTI0 #28 US0_CTS #27 TIM0_CDTI1 #27 US0_RTS #26 TIM0_CDTI2 #26 US1_TX #31 TIM1_CC0 #31 US1_RX #30 FRC_DCLK #31 TIM1_CC1 #30 US1_CLK #29 FRC_DOUT #30 TIM1_CC2 #29 US1_CS #28 FRC_DFRAME #29 BUSAY TIM1_CC3 #28 US1_CTS #27 MODEM_DCLK #31 BUSBX WTIM1_CC0 #31 US1_RTS #26 MODEM_DIN #30 WTIM1_CC1 #29 US2_TX #20 MODEM_DOUT #29 WTIM1_CC2 #27 US2_RX #19 MODEM_ANT0 #28 WTIM1_CC3 #25 US2_CLK #18 MODEM_ANT1 #27 LETIM0_OUT0 #31 US2_CS #17 LETIM0_OUT1 #30 US2_CTS #16 PCNT0_S0IN #31 US2_RTS #15 PCNT0_S1IN #30 LEU0_TX #31 PCNT1_S0IN #20 LEU0_RX #30 PCNT1_S1IN #19 I2C0_SDA #31 CMU_CLKI0 #1 CMU_CLK0 #7 PRS_CH0 #7 PRS_CH1 #6 PRS_CH2 #5 PRS_CH3 #4 ACMP0_O #31 ACMP1_O #31 GPIO_EM4WU1 I2C0_SCL #30 WTIM1_CC1 #30 WTIM1_CC2 #28 PF8 BUSBY BUSAX WTIM1_CC3 #26 PCNT1_S0IN #21 PCNT1_S1IN #20 PCNT2_S0IN #21 PCNT2_S1IN #20 silabs.com | Building a more connected world. US2_TX #21 US2_RX #20 US2_CLK #19 US2_CS #18 US2_CTS #17 ETM_TCLK #0 US2_RTS #16 I2C1_SDA #21 I2C1_SCL #20 Rev. 1.6 | 174 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers WTIM1_CC1 #31 WTIM1_CC2 #29 PF9 BUSAY BUSBX WTIM1_CC3 #27 PCNT1_S0IN #22 PCNT1_S1IN #21 PCNT2_S0IN #22 PCNT2_S1IN #21 Communication Radio Other US2_TX #22 US2_RX #21 US2_CLK #20 US2_CS #19 US2_CTS #18 ETM_TD0 #0 US2_RTS #17 I2C1_SDA #22 I2C1_SCL #21 US2_TX #23 PF10 WTIM1_CC2 #30 US2_RX #22 WTIM1_CC3 #28 US2_CLK #21 BUSBY PCNT1_S0IN #23 US2_CS #20 BUSAX PCNT1_S1IN #22 US2_CTS #19 PCNT2_S0IN #23 US2_RTS #18 PCNT2_S1IN #22 I2C1_SDA #23 ETM_TD1 #0 I2C1_SCL #22 US2_TX #24 US2_RX #23 US2_CLK #22 US2_CS #21 PF11 WTIM1_CC2 #31 US2_CTS #20 WTIM1_CC3 #29 US2_RTS #19 BUSAY PCNT1_S0IN #24 US3_TX #24 BUSBX PCNT1_S1IN #23 US3_RX #23 PCNT2_S0IN #24 US3_CLK #22 PCNT2_S1IN #23 US3_CS #21 ETM_TD2 #0 US3_CTS #20 US3_RTS #19 I2C1_SDA #24 I2C1_SCL #23 silabs.com | Building a more connected world. Rev. 1.6 | 175 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US2_TX #25 US2_RX #24 US2_CLK #23 US2_CS #22 WTIM1_CC3 #30 PF12 BUSBY BUSAX PCNT1_S0IN #25 PCNT1_S1IN #24 PCNT2_S0IN #25 PCNT2_S1IN #24 US2_CTS #21 US2_RTS #20 US3_TX #25 US3_RX #24 ETM_TD3 #0 US3_CLK #23 US3_CS #22 US3_CTS #21 US3_RTS #20 I2C1_SDA #25 I2C1_SCL #24 US2_TX #26 US2_RX #25 US2_CLK #24 US2_CS #23 WTIM1_CC3 #31 PF13 BUSAY BUSBX PCNT1_S0IN #26 PCNT1_S1IN #25 PCNT2_S0IN #26 PCNT2_S1IN #25 US2_CTS #22 US2_RTS #21 US3_TX #26 US3_RX #25 US3_CLK #24 US3_CS #23 US3_CTS #22 US3_RTS #21 I2C1_SDA #26 I2C1_SCL #25 silabs.com | Building a more connected world. Rev. 1.6 | 176 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US2_TX #27 US2_RX #26 US2_CLK #25 US2_CS #24 US2_CTS #23 PF14 PCNT1_S0IN #27 US2_RTS #22 BUSBY PCNT1_S1IN #26 US3_TX #27 BUSAX PCNT2_S0IN #27 US3_RX #26 PCNT2_S1IN #26 US3_CLK #25 US3_CS #24 US3_CTS #23 US3_RTS #22 I2C1_SDA #27 I2C1_SCL #26 US2_TX #28 US2_RX #27 US2_CLK #26 US2_CS #25 US2_CTS #24 PF15 PCNT1_S0IN #28 US2_RTS #23 BUSAY PCNT1_S1IN #27 US3_TX #28 BUSBX PCNT2_S0IN #28 US3_RX #27 PCNT2_S1IN #27 US3_CLK #26 US3_CS #25 US3_CTS #24 US3_RTS #23 I2C1_SDA #28 I2C1_SCL #27 US2_TX #5 US2_RX #4 PI0 BUSADC0Y US2_CLK #3 BUSADC0X US2_CS #2 LES_ALTEX4 US2_CTS #1 US2_RTS #0 silabs.com | Building a more connected world. Rev. 1.6 | 177 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US2_TX #6 US2_RX #5 PI1 BUSADC0Y US2_CLK #4 BUSADC0X US2_CS #3 LES_ALTEX5 US2_CTS #2 US2_RTS #1 US2_TX #7 US2_RX #6 US2_CLK #5 US2_CS #4 US2_CTS #3 PI2 PCNT1_S0IN #4 US2_RTS #2 BUSADC0Y PCNT1_S1IN #3 US3_TX #8 LES_ALTEX6 BUSADC0X PCNT2_S0IN #4 US3_RX #7 ETM_TCLK #2 PCNT2_S1IN #3 US3_CLK #6 US3_CS #5 US3_CTS #4 US3_RTS #3 I2C1_SDA #4 I2C1_SCL #3 US2_TX #8 US2_RX #7 US2_CLK #6 US2_CS #5 US2_CTS #4 PI3 PCNT1_S0IN #5 US2_RTS #3 BUSADC0Y PCNT1_S1IN #4 US3_TX #9 LES_ALTEX7 BUSADC0X PCNT2_S0IN #5 US3_RX #8 ETM_TD0 #2 PCNT2_S1IN #4 US3_CLK #7 US3_CS #6 US3_CTS #5 US3_RTS #4 I2C1_SDA #5 I2C1_SCL #4 silabs.com | Building a more connected world. Rev. 1.6 | 178 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US3_TX #16 US3_RX #15 PJ14 PCNT1_S0IN #11 US3_CLK #14 BUSACMP1Y PCNT1_S1IN #10 US3_CS #13 BUSACMP1X PCNT2_S0IN #11 US3_CTS #12 PCNT2_S1IN #10 US3_RTS #11 LES_ALTEX2 I2C1_SDA #11 I2C1_SCL #10 US3_TX #17 US3_RX #16 PJ15 PCNT1_S0IN #12 US3_CLK #15 BUSACMP1Y PCNT1_S1IN #11 US3_CS #14 BUSACMP1X PCNT2_S0IN #12 US3_CTS #13 PCNT2_S1IN #11 US3_RTS #12 LES_ALTEX3 I2C1_SDA #12 I2C1_SCL #11 US2_TX #29 US2_RX #28 US2_CLK #27 US2_CS #26 US2_CTS #25 PK0 IDAC0_OUT PCNT1_S0IN #29 US2_RTS #24 PCNT1_S1IN #28 US3_TX #29 PCNT2_S0IN #29 US3_RX #28 PCNT2_S1IN #28 US3_CLK #27 US3_CS #26 US3_CTS #25 US3_RTS #24 I2C1_SDA #29 I2C1_SCL #28 silabs.com | Building a more connected world. Rev. 1.6 | 179 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions GPIO Name Pin Alternate Functionality / Description Analog Timers Communication Radio Other US2_TX #30 US2_RX #29 US2_CLK #28 US2_CS #27 US2_CTS #26 PK1 PCNT1_S0IN #30 US2_RTS #25 PCNT1_S1IN #29 US3_TX #30 PCNT2_S0IN #30 US3_RX #29 PCNT2_S1IN #29 US3_CLK #28 US3_CS #27 US3_CTS #26 US3_RTS #25 I2C1_SDA #30 I2C1_SCL #29 US2_TX #31 US2_RX #30 US2_CLK #29 US2_CS #28 US2_CTS #27 PK2 PCNT1_S0IN #31 US2_RTS #26 PCNT1_S1IN #30 US3_TX #31 PCNT2_S0IN #31 US3_RX #30 PCNT2_S1IN #30 US3_CLK #29 US3_CS #28 US3_CTS #27 US3_RTS #26 I2C1_SDA #31 I2C1_SCL #30 silabs.com | Building a more connected world. Rev. 1.6 | 180 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions 6.8 Alternate Functionality Overview A wide selection of alternate functionality is available for multiplexing to various pins. The following table shows the name of the alternate functionality in the first column, followed by columns showing the possible LOCATION bitfield settings and the associated GPIO pin. Refer to 6.7 GPIO Functionality Table for a list of functions available on each GPIO pin. Note: Some functionality, such as analog interfaces, do not have alternate settings or a LOCATION bitfield. In these cases, the pinout is shown in the column corresponding to LOCATION 0. Table 6.8. Alternate Functionality Overview Alternate Functionality ACMP0_O ACMP1_O LOCATION 0-3 4-7 8 - 11 12 - 15 16 - 19 20 - 23 0: PA0 4: PA4 8: PB13 1: PA1 5: PA5 2: PA2 24 - 27 28 - 31 12: PC7 16: PC11 20: PD12 24: PF0 28: PF4 9: PB14 13: PC8 17: PD9 21: PD13 25: PF1 29: PF5 6: PB11 10: PB15 14: PC9 18: PD10 22: PD14 26: PF2 30: PF6 3: PA3 7: PB12 11: PC6 15: PC10 19: PD11 23: PD15 27: PF3 31: PF7 0: PA0 4: PA4 8: PB13 12: PC7 16: PC11 20: PD12 24: PF0 28: PF4 1: PA1 5: PA5 9: PB14 13: PC8 17: PD9 21: PD13 25: PF1 29: PF5 2: PA2 6: PB11 10: PB15 14: PC9 18: PD10 22: PD14 26: PF2 30: PF6 3: PA3 7: PB12 11: PC6 15: PC10 19: PD11 23: PD15 27: PF3 31: PF7 Description Analog comparator ACMP0, digital output. Analog comparator ACMP1, digital output. 0: PA0 Analog to digital converter ADC0 external reference input negative pin. 0: PA1 Analog to digital converter ADC0 external reference input positive pin. BOOT_RX 0: PF1 Bootloader RX. BOOT_TX 0: PF0 Bootloader TX. ADC0_EXTN ADC0_EXTP CMU_CLK0 CMU_CLK1 CMU_CLKI0 0: PA1 4: PD9 1: PB15 5: PD14 2: PC6 6: PF2 3: PC11 7: PF7 0: PA0 4: PD10 1: PB14 5: PD15 2: PC7 6: PF3 3: PC10 7: PF6 0: PB13 4: PA5 1: PF7 2: PC6 Clock Management Unit, clock output number 0. Clock Management Unit, clock output number 1. Clock Management Unit, clock input number 0. 3: PB6 silabs.com | Building a more connected world. Rev. 1.6 | 181 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality LOCATION 0-3 4-7 0: PF0 DBG_SWCLKTCK 12 - 15 16 - 19 20 - 23 24 - 27 28 - 31 Description Debug-interface Serial Wire clock input and JTAG Test Clock. Note that this function is enabled to the pin out of reset, and has a built-in pull down. 0: PF1 DBG_SWDIOTMS Debug-interface Serial Wire data input / output and JTAG Test Mode Select. Note that this function is enabled to the pin out of reset, and has a built-in pull up. 0: PF2 1: PB13 DBG_SWO 8 - 11 2: PD15 3: PC11 0: PF3 Debug-interface Serial Wire viewer Output. Note that this function is not enabled after reset, and must be enabled by software to be used. Debug-interface JTAG Test Data In. Note that this function becomes available after the first valid JTAG command is received, and has a built-in pull up when JTAG is active. DBG_TDI 0: PF2 Debug-interface JTAG Test Data Out. Note that this function becomes available after the first valid JTAG command is received. DBG_TDO 0: PF8 ETM_TCLK 1: PA5 2: PI2 Embedded Trace Module ETM clock . 3: PC6 silabs.com | Building a more connected world. Rev. 1.6 | 182 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality LOCATION 0-3 4-7 8 - 11 12 - 15 16 - 19 20 - 23 24 - 27 28 - 31 Description 0: PF9 ETM_TD0 Embedded Trace Module ETM data 0. 1: PA6 2: PI3 3: PC7 0: PF10 ETM_TD1 Embedded Trace Module ETM data 1. 1: PA7 2: PB6 3: PC8 0: PF11 ETM_TD2 Embedded Trace Module ETM data 2. 1: PA8 2: PB7 3: PC9 0: PF12 ETM_TD3 Embedded Trace Module ETM data 3. 1: PA9 2: PB8 3: PC10 FRC_DCLK FRC_DFRAME FRC_DOUT 0: PA0 4: PA4 8: PB13 12: PC7 16: PC11 20: PD12 24: PF0 28: PF4 1: PA1 5: PA5 9: PB14 13: PC8 17: PD9 21: PD13 25: PF1 29: PF5 2: PA2 6: PB11 10: PB15 14: PC9 18: PD10 22: PD14 26: PF2 30: PF6 3: PA3 7: PB12 11: PC6 15: PC10 19: PD11 23: PD15 27: PF3 31: PF7 0: PA2 4: PB11 8: PB15 12: PC9 16: PD10 20: PD14 24: PF2 28: PF6 1: PA3 5: PB12 9: PC6 13: PC10 17: PD11 21: PD15 25: PF3 29: PF7 2: PA4 6: PB13 10: PC7 14: PC11 18: PD12 22: PF0 26: PF4 30: PA0 3: PA5 7: PB14 11: PC8 15: PD9 19: PD13 23: PF1 27: PF5 31: PA1 0: PA1 4: PA5 8: PB14 12: PC8 16: PD9 20: PD13 24: PF1 28: PF5 1: PA2 5: PB11 9: PB15 13: PC9 17: PD10 21: PD14 25: PF2 29: PF6 2: PA3 6: PB12 10: PC6 14: PC10 18: PD11 22: PD15 26: PF3 30: PF7 3: PA4 7: PB13 11: PC7 15: PC11 19: PD12 23: PF0 27: PF4 31: PA0 Frame Controller, Data Sniffer Clock. Frame Controller, Data Sniffer Frame active Frame Controller, Data Sniffer Output. 0: PF2 Pin can be used to wake the system up from EM4 0: PF7 Pin can be used to wake the system up from EM4 0: PD14 Pin can be used to wake the system up from EM4 GPIO_EM4WU0 GPIO_EM4WU1 GPIO_EM4WU4 silabs.com | Building a more connected world. Rev. 1.6 | 183 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality LOCATION 0-3 4-7 8 - 11 12 - 15 16 - 19 20 - 23 24 - 27 28 - 31 0: PA3 Pin can be used to wake the system up from EM4 0: PB13 Pin can be used to wake the system up from EM4 0: PC10 Pin can be used to wake the system up from EM4 GPIO_EM4WU8 GPIO_EM4WU9 GPIO_EM4WU12 I2C0_SCL I2C0_SDA I2C1_SCL I2C1_SDA IDAC0_OUT LES_ALTEX0 LES_ALTEX1 LES_ALTEX2 LES_ALTEX3 LES_ALTEX4 LES_ALTEX5 LES_ALTEX6 LES_ALTEX7 Description 0: PA1 4: PA5 8: PB14 12: PC8 16: PD9 20: PD13 24: PF1 28: PF5 1: PA2 5: PB11 9: PB15 13: PC9 17: PD10 21: PD14 25: PF2 29: PF6 2: PA3 6: PB12 10: PC6 14: PC10 18: PD11 22: PD15 26: PF3 30: PF7 3: PA4 7: PB13 11: PC7 15: PC11 19: PD12 23: PF0 27: PF4 31: PA0 0: PA0 4: PA4 8: PB13 12: PC7 16: PC11 20: PD12 24: PF0 28: PF4 1: PA1 5: PA5 9: PB14 13: PC8 17: PD9 21: PD13 25: PF1 29: PF5 2: PA2 6: PB11 10: PB15 14: PC9 18: PD10 22: PD14 26: PF2 30: PF6 3: PA3 7: PB12 11: PC6 15: PC10 19: PD11 23: PD15 27: PF3 31: PF7 0: PA7 4: PI3 8: PB9 12: PC0 16: PC4 20: PF8 24: PF12 28: PK0 1: PA8 5: PB6 9: PB10 13: PC1 17: PC5 21: PF9 25: PF13 29: PK1 2: PA9 6: PB7 10: PJ14 14: PC2 18: PC10 22: PF10 26: PF14 30: PK2 3: PI2 7: PB8 11: PJ15 15: PC3 19: PC11 23: PF11 27: PF15 31: PA6 0: PA6 4: PI2 8: PB8 12: PJ15 16: PC3 20: PC11 24: PF11 28: PF15 1: PA7 5: PI3 9: PB9 13: PC0 17: PC4 21: PF8 25: PF12 29: PK0 2: PA8 6: PB6 10: PB10 14: PC1 18: PC5 22: PF9 26: PF13 30: PK1 3: PA9 7: PB7 11: PJ14 15: PC2 19: PC10 23: PF10 27: PF14 31: PK2 I2C0 Serial Clock Line input / output. I2C0 Serial Data input / output. I2C1 Serial Clock Line input / output. I2C1 Serial Data input / output. 0: PK0 IDAC0 output. 0: PA8 LESENSE alternate excite output 0. 0: PA9 LESENSE alternate excite output 1. 0: PJ14 LESENSE alternate excite output 2. 0: PJ15 LESENSE alternate excite output 3. 0: PI0 LESENSE alternate excite output 4. 0: PI1 LESENSE alternate excite output 5. 0: PI2 LESENSE alternate excite output 6. 0: PI3 LESENSE alternate excite output 7. silabs.com | Building a more connected world. Rev. 1.6 | 184 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality LES_CH0 LES_CH1 LES_CH2 LES_CH3 LES_CH4 LES_CH5 LES_CH6 LES_CH7 LES_CH8 LES_CH9 LES_CH10 LES_CH11 LES_CH12 LES_CH13 LES_CH14 LES_CH15 LETIM0_OUT0 LETIM0_OUT1 LOCATION 0-3 4-7 8 - 11 12 - 15 16 - 19 20 - 23 24 - 27 28 - 31 Description 0: PD8 LESENSE channel 0. 0: PD9 LESENSE channel 1. 0: PD10 LESENSE channel 2. 0: PD11 LESENSE channel 3. 0: PD12 LESENSE channel 4. 0: PD13 LESENSE channel 5. 0: PD14 LESENSE channel 6. 0: PD15 LESENSE channel 7. 0: PA0 LESENSE channel 8. 0: PA1 LESENSE channel 9. 0: PA2 LESENSE channel 10. 0: PA3 LESENSE channel 11. 0: PA4 LESENSE channel 12. 0: PA5 LESENSE channel 13. 0: PA6 LESENSE channel 14. 0: PA7 LESENSE channel 15. 0: PA0 4: PA4 8: PB13 12: PC7 16: PC11 20: PD12 24: PF0 28: PF4 1: PA1 5: PA5 9: PB14 13: PC8 17: PD9 21: PD13 25: PF1 29: PF5 2: PA2 6: PB11 10: PB15 14: PC9 18: PD10 22: PD14 26: PF2 30: PF6 3: PA3 7: PB12 11: PC6 15: PC10 19: PD11 23: PD15 27: PF3 31: PF7 0: PA1 4: PA5 8: PB14 12: PC8 16: PD9 20: PD13 24: PF1 28: PF5 1: PA2 5: PB11 9: PB15 13: PC9 17: PD10 21: PD14 25: PF2 29: PF6 2: PA3 6: PB12 10: PC6 14: PC10 18: PD11 22: PD15 26: PF3 30: PF7 3: PA4 7: PB13 11: PC7 15: PC11 19: PD12 23: PF0 27: PF4 31: PA0 silabs.com | Building a more connected world. Low Energy Timer LETIM0, output channel 0. Low Energy Timer LETIM0, output channel 1. Rev. 1.6 | 185 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality LEU0_RX LEU0_TX LOCATION 0-3 4-7 8 - 11 12 - 15 16 - 19 20 - 23 24 - 27 28 - 31 0: PA1 4: PA5 8: PB14 12: PC8 16: PD9 20: PD13 24: PF1 28: PF5 1: PA2 5: PB11 9: PB15 13: PC9 17: PD10 21: PD14 25: PF2 29: PF6 2: PA3 6: PB12 10: PC6 14: PC10 18: PD11 22: PD15 26: PF3 30: PF7 3: PA4 7: PB13 11: PC7 15: PC11 19: PD12 23: PF0 27: PF4 31: PA0 0: PA0 4: PA4 8: PB13 12: PC7 16: PC11 20: PD12 24: PF0 28: PF4 1: PA1 5: PA5 9: PB14 13: PC8 17: PD9 21: PD13 25: PF1 29: PF5 2: PA2 6: PB11 10: PB15 14: PC9 18: PD10 22: PD14 26: PF2 30: PF6 3: PA3 7: PB12 11: PC6 15: PC10 19: PD11 23: PD15 27: PF3 31: PF7 MODEM_DCLK MODEM_DIN MODEM_DOUT LEUART0 Transmit output. Also used as receive input in half duplex communication. Low Frequency Crystal (typically 32.768 kHz) negative pin. Also used as an optional external clock input pin. 0: PB15 Low Frequency Crystal (typically 32.768 kHz) positive pin. LFXTAL_P MODEM_ANT1 LEUART0 Receive input. 0: PB14 LFXTAL_N MODEM_ANT0 Description 0: PA3 4: PB12 8: PC6 12: PC10 16: PD11 20: PD15 24: PF3 28: PF7 1: PA4 5: PB13 9: PC7 13: PC11 17: PD12 21: PF0 25: PF4 29: PA0 2: PA5 6: PB14 10: PC8 14: PD9 18: PD13 22: PF1 26: PF5 30: PA1 3: PB11 7: PB15 11: PC9 15: PD10 19: PD14 23: PF2 27: PF6 31: PA2 0: PA4 4: PB13 8: PC7 12: PC11 16: PD12 20: PF0 24: PF4 28: PA0 1: PA5 5: PB14 9: PC8 13: PD9 17: PD13 21: PF1 25: PF5 29: PA1 2: PB11 6: PB15 10: PC9 14: PD10 18: PD14 22: PF2 26: PF6 30: PA2 3: PB12 7: PC6 11: PC10 15: PD11 19: PD15 23: PF3 27: PF7 31: PA3 0: PA0 4: PA4 8: PB13 12: PC7 16: PC11 20: PD12 24: PF0 28: PF4 1: PA1 5: PA5 9: PB14 13: PC8 17: PD9 21: PD13 25: PF1 29: PF5 2: PA2 6: PB11 10: PB15 14: PC9 18: PD10 22: PD14 26: PF2 30: PF6 3: PA3 7: PB12 11: PC6 15: PC10 19: PD11 23: PD15 27: PF3 31: PF7 0: PA1 4: PA5 8: PB14 12: PC8 16: PD9 20: PD13 24: PF1 28: PF5 1: PA2 5: PB11 9: PB15 13: PC9 17: PD10 21: PD14 25: PF2 29: PF6 2: PA3 6: PB12 10: PC6 14: PC10 18: PD11 22: PD15 26: PF3 30: PF7 3: PA4 7: PB13 11: PC7 15: PC11 19: PD12 23: PF0 27: PF4 31: PA0 0: PA2 4: PB11 8: PB15 12: PC9 16: PD10 20: PD14 24: PF2 28: PF6 1: PA3 5: PB12 9: PC6 13: PC10 17: PD11 21: PD15 25: PF3 29: PF7 2: PA4 6: PB13 10: PC7 14: PC11 18: PD12 22: PF0 26: PF4 30: PA0 3: PA5 7: PB14 11: PC8 15: PD9 19: PD13 23: PF1 27: PF5 31: PA1 silabs.com | Building a more connected world. MODEM antenna control output 0, used for antenna diversity. MODEM antenna control output 1, used for antenna diversity. MODEM data clock out. MODEM data in. MODEM data out. Rev. 1.6 | 186 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality LOCATION 0-3 4-7 8 - 11 12 - 15 16 - 19 20 - 23 24 - 27 28 - 31 0: PA4 Operational Amplifier 0 external negative input. 0: PA2 Operational Amplifier 0 external positive input. 0: PD15 Operational Amplifier 1 external negative input. 0: PD13 Operational Amplifier 1 external positive input. 0: PB13 Operational Amplifier 2 external negative input. 0: PB12 Operational Amplifier 2 output. 0: PB9 Operational Amplifier 2 alternative output. OPA0_N OPA0_P OPA1_N OPA1_P OPA2_N OPA2_OUT OPA2_OUTALT 1: PB10 0: PB11 Operational Amplifier 2 external positive input. OPA2_P PCNT0_S0IN PCNT0_S1IN PCNT1_S0IN PCNT1_S1IN Description 0: PA0 4: PA4 8: PB13 12: PC7 16: PC11 20: PD12 24: PF0 28: PF4 1: PA1 5: PA5 9: PB14 13: PC8 17: PD9 21: PD13 25: PF1 29: PF5 2: PA2 6: PB11 10: PB15 14: PC9 18: PD10 22: PD14 26: PF2 30: PF6 3: PA3 7: PB12 11: PC6 15: PC10 19: PD11 23: PD15 27: PF3 31: PF7 0: PA1 4: PA5 8: PB14 12: PC8 16: PD9 20: PD13 24: PF1 28: PF5 1: PA2 5: PB11 9: PB15 13: PC9 17: PD10 21: PD14 25: PF2 29: PF6 2: PA3 6: PB12 10: PC6 14: PC10 18: PD11 22: PD15 26: PF3 30: PF7 3: PA4 7: PB13 11: PC7 15: PC11 19: PD12 23: PF0 27: PF4 31: PA0 0: PA6 4: PI2 8: PB8 12: PJ15 16: PC3 20: PF7 24: PF11 28: PF15 1: PA7 5: PI3 9: PB9 13: PC0 17: PC4 21: PF8 25: PF12 29: PK0 2: PA8 6: PB6 10: PB10 14: PC1 18: PC5 22: PF9 26: PF13 30: PK1 3: PA9 7: PB7 11: PJ14 15: PC2 19: PF6 23: PF10 27: PF14 31: PK2 0: PA7 4: PI3 8: PB9 12: PC0 16: PC4 20: PF8 24: PF12 28: PK0 1: PA8 5: PB6 9: PB10 13: PC1 17: PC5 21: PF9 25: PF13 29: PK1 2: PA9 6: PB7 10: PJ14 14: PC2 18: PF6 22: PF10 26: PF14 30: PK2 3: PI2 7: PB8 11: PJ15 15: PC3 19: PF7 23: PF11 27: PF15 31: PA6 silabs.com | Building a more connected world. Pulse Counter PCNT0 input number 0. Pulse Counter PCNT0 input number 1. Pulse Counter PCNT1 input number 0. Pulse Counter PCNT1 input number 1. Rev. 1.6 | 187 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality PCNT2_S0IN PCNT2_S1IN PRS_CH0 PRS_CH1 PRS_CH2 PRS_CH3 PRS_CH4 LOCATION 0-3 4-7 8 - 11 12 - 15 16 - 19 20 - 23 24 - 27 28 - 31 0: PA6 4: PI2 8: PB8 12: PJ15 16: PC3 20: PC11 24: PF11 28: PF15 1: PA7 5: PI3 9: PB9 13: PC0 17: PC4 21: PF8 25: PF12 29: PK0 2: PA8 6: PB6 10: PB10 14: PC1 18: PC5 22: PF9 26: PF13 30: PK1 3: PA9 7: PB7 11: PJ14 15: PC2 19: PC10 23: PF10 27: PF14 31: PK2 0: PA7 4: PI3 8: PB9 12: PC0 16: PC4 20: PF8 24: PF12 28: PK0 1: PA8 5: PB6 9: PB10 13: PC1 17: PC5 21: PF9 25: PF13 29: PK1 2: PA9 6: PB7 10: PJ14 14: PC2 18: PC10 22: PF10 26: PF14 30: PK2 3: PI2 7: PB8 11: PJ15 15: PC3 19: PC11 23: PF11 27: PF15 31: PA6 0: PF0 4: PF4 8: PC6 12: PC10 1: PF1 5: PF5 9: PC7 13: PC11 2: PF2 6: PF6 10: PC8 3: PF3 7: PF7 11: PC9 0: PF1 4: PF5 1: PF2 5: PF6 2: PF3 6: PF7 3: PF4 7: PF0 0: PF2 4: PF6 1: PF3 5: PF7 2: PF4 6: PF0 3: PF5 7: PF1 0: PF3 4: PF7 8: PD9 12: PD13 1: PF4 5: PF0 9: PD10 13: PD14 2: PF5 6: PF1 10: PD11 14: PD15 3: PF6 7: PF2 11: PD12 0: PD9 4: PD13 1: PD10 5: PD14 2: PD11 6: PD15 Description Pulse Counter PCNT2 input number 0. Pulse Counter PCNT2 input number 1. Peripheral Reflex System PRS, channel 0. Peripheral Reflex System PRS, channel 1. Peripheral Reflex System PRS, channel 2. Peripheral Reflex System PRS, channel 3. Peripheral Reflex System PRS, channel 4. 3: PD12 PRS_CH5 0: PD10 4: PD14 1: PD11 5: PD15 2: PD12 6: PD9 Peripheral Reflex System PRS, channel 5. 3: PD13 PRS_CH6 0: PA0 4: PA4 8: PB13 12: PD10 16: PD14 1: PA1 5: PA5 9: PB14 13: PD11 17: PD15 2: PA2 6: PB11 10: PB15 14: PD12 3: PA3 7: PB12 11: PD9 15: PD13 silabs.com | Building a more connected world. Peripheral Reflex System PRS, channel 6. Rev. 1.6 | 188 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality PRS_CH7 PRS_CH8 PRS_CH9 PRS_CH10 LOCATION 0-3 4-7 8 - 11 12 - 15 0: PA1 4: PA5 8: PB14 1: PA2 5: PB11 9: PB15 2: PA3 6: PB12 10: PA0 3: PA4 7: PB13 0: PA2 4: PB11 8: PB15 1: PA3 5: PB12 9: PA0 2: PA4 6: PB13 10: PA1 3: PA5 7: PB14 0: PA3 4: PB12 8: PA0 12: PC7 1: PA4 5: PB13 9: PA1 13: PC8 2: PA5 6: PB14 10: PA2 14: PC9 3: PB11 7: PB15 11: PC6 15: PC10 0: PC6 4: PC10 1: PC7 5: PC11 16 - 19 20 - 23 24 - 27 28 - 31 Description Peripheral Reflex System PRS, channel 7. Peripheral Reflex System PRS, channel 8. 16: PC11 Peripheral Reflex System PRS, channel 9. Peripheral Reflex System PRS, channel 10. 2: PC8 3: PC9 PRS_CH11 0: PC7 4: PC11 1: PC8 5: PC6 Peripheral Reflex System PRS, channel 11. 2: PC9 3: PC10 TIM0_CC0 TIM0_CC1 TIM0_CC2 TIM0_CDTI0 0: PA0 4: PA4 8: PB13 12: PC7 16: PC11 20: PD12 24: PF0 28: PF4 1: PA1 5: PA5 9: PB14 13: PC8 17: PD9 21: PD13 25: PF1 29: PF5 2: PA2 6: PB11 10: PB15 14: PC9 18: PD10 22: PD14 26: PF2 30: PF6 3: PA3 7: PB12 11: PC6 15: PC10 19: PD11 23: PD15 27: PF3 31: PF7 0: PA1 4: PA5 8: PB14 12: PC8 16: PD9 20: PD13 24: PF1 28: PF5 1: PA2 5: PB11 9: PB15 13: PC9 17: PD10 21: PD14 25: PF2 29: PF6 2: PA3 6: PB12 10: PC6 14: PC10 18: PD11 22: PD15 26: PF3 30: PF7 3: PA4 7: PB13 11: PC7 15: PC11 19: PD12 23: PF0 27: PF4 31: PA0 0: PA2 4: PB11 8: PB15 12: PC9 16: PD10 20: PD14 24: PF2 28: PF6 1: PA3 5: PB12 9: PC6 13: PC10 17: PD11 21: PD15 25: PF3 29: PF7 2: PA4 6: PB13 10: PC7 14: PC11 18: PD12 22: PF0 26: PF4 30: PA0 3: PA5 7: PB14 11: PC8 15: PD9 19: PD13 23: PF1 27: PF5 31: PA1 0: PA3 4: PB12 8: PC6 12: PC10 16: PD11 20: PD15 24: PF3 28: PF7 1: PA4 5: PB13 9: PC7 13: PC11 17: PD12 21: PF0 25: PF4 29: PA0 2: PA5 6: PB14 10: PC8 14: PD9 18: PD13 22: PF1 26: PF5 30: PA1 3: PB11 7: PB15 11: PC9 15: PD10 19: PD14 23: PF2 27: PF6 31: PA2 silabs.com | Building a more connected world. Timer 0 Capture Compare input / output channel 0. Timer 0 Capture Compare input / output channel 1. Timer 0 Capture Compare input / output channel 2. Timer 0 Complimentary Dead Time Insertion channel 0. Rev. 1.6 | 189 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality TIM0_CDTI1 TIM0_CDTI2 TIM1_CC0 TIM1_CC1 TIM1_CC2 TIM1_CC3 US0_CLK US0_CS US0_CTS LOCATION 0-3 4-7 0: PA4 4: PB13 1: PA5 12 - 15 16 - 19 8: PC7 12: PC11 16: PD12 20: PF0 24: PF4 28: PA0 5: PB14 9: PC8 13: PD9 17: PD13 21: PF1 25: PF5 29: PA1 2: PB11 6: PB15 10: PC9 14: PD10 18: PD14 22: PF2 26: PF6 30: PA2 3: PB12 7: PC6 11: PC10 15: PD11 19: PD15 23: PF3 27: PF7 31: PA3 0: PA5 4: PB14 8: PC8 12: PD9 16: PD13 20: PF1 24: PF5 28: PA1 1: PB11 5: PB15 9: PC9 13: PD10 17: PD14 21: PF2 25: PF6 29: PA2 2: PB12 6: PC6 10: PC10 14: PD11 18: PD15 22: PF3 26: PF7 30: PA3 3: PB13 7: PC7 11: PC11 15: PD12 19: PF0 23: PF4 27: PA0 31: PA4 0: PA0 4: PA4 8: PB13 12: PC7 16: PC11 20: PD12 24: PF0 28: PF4 1: PA1 5: PA5 9: PB14 13: PC8 17: PD9 21: PD13 25: PF1 29: PF5 2: PA2 6: PB11 10: PB15 14: PC9 18: PD10 22: PD14 26: PF2 30: PF6 3: PA3 7: PB12 11: PC6 15: PC10 19: PD11 23: PD15 27: PF3 31: PF7 0: PA1 4: PA5 8: PB14 12: PC8 16: PD9 20: PD13 24: PF1 28: PF5 1: PA2 5: PB11 9: PB15 13: PC9 17: PD10 21: PD14 25: PF2 29: PF6 2: PA3 6: PB12 10: PC6 14: PC10 18: PD11 22: PD15 26: PF3 30: PF7 3: PA4 7: PB13 11: PC7 15: PC11 19: PD12 23: PF0 27: PF4 31: PA0 0: PA2 4: PB11 8: PB15 12: PC9 16: PD10 20: PD14 24: PF2 28: PF6 1: PA3 5: PB12 9: PC6 13: PC10 17: PD11 21: PD15 25: PF3 29: PF7 2: PA4 6: PB13 10: PC7 14: PC11 18: PD12 22: PF0 26: PF4 30: PA0 3: PA5 7: PB14 11: PC8 15: PD9 19: PD13 23: PF1 27: PF5 31: PA1 0: PA3 4: PB12 8: PC6 12: PC10 16: PD11 20: PD15 24: PF3 28: PF7 1: PA4 5: PB13 9: PC7 13: PC11 17: PD12 21: PF0 25: PF4 29: PA0 2: PA5 6: PB14 10: PC8 14: PD9 18: PD13 22: PF1 26: PF5 30: PA1 3: PB11 7: PB15 11: PC9 15: PD10 19: PD14 23: PF2 27: PF6 31: PA2 0: PA2 4: PB11 8: PB15 12: PC9 16: PD10 20: PD14 24: PF2 28: PF6 1: PA3 5: PB12 9: PC6 13: PC10 17: PD11 21: PD15 25: PF3 29: PF7 2: PA4 6: PB13 10: PC7 14: PC11 18: PD12 22: PF0 26: PF4 30: PA0 3: PA5 7: PB14 11: PC8 15: PD9 19: PD13 23: PF1 27: PF5 31: PA1 0: PA3 4: PB12 8: PC6 12: PC10 16: PD11 20: PD15 24: PF3 28: PF7 1: PA4 5: PB13 9: PC7 13: PC11 17: PD12 21: PF0 25: PF4 29: PA0 2: PA5 6: PB14 10: PC8 14: PD9 18: PD13 22: PF1 26: PF5 30: PA1 3: PB11 7: PB15 11: PC9 15: PD10 19: PD14 23: PF2 27: PF6 31: PA2 0: PA4 4: PB13 8: PC7 12: PC11 16: PD12 20: PF0 24: PF4 28: PA0 1: PA5 5: PB14 9: PC8 13: PD9 17: PD13 21: PF1 25: PF5 29: PA1 2: PB11 6: PB15 10: PC9 14: PD10 18: PD14 22: PF2 26: PF6 30: PA2 3: PB12 7: PC6 11: PC10 15: PD11 19: PD15 23: PF3 27: PF7 31: PA3 silabs.com | Building a more connected world. 8 - 11 20 - 23 24 - 27 28 - 31 Description Timer 0 Complimentary Dead Time Insertion channel 1. Timer 0 Complimentary Dead Time Insertion channel 2. Timer 1 Capture Compare input / output channel 0. Timer 1 Capture Compare input / output channel 1. Timer 1 Capture Compare input / output channel 2. Timer 1 Capture Compare input / output channel 3. USART0 clock input / output. USART0 chip select input / output. USART0 Clear To Send hardware flow control input. Rev. 1.6 | 190 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality US0_RTS US0_RX US0_TX US1_CLK US1_CS US1_CTS US1_RTS US1_RX LOCATION 0-3 4-7 0: PA5 4: PB14 8: PC8 12: PD9 16: PD13 20: PF1 24: PF5 28: PA1 1: PB11 5: PB15 9: PC9 13: PD10 17: PD14 21: PF2 25: PF6 29: PA2 2: PB12 6: PC6 10: PC10 14: PD11 18: PD15 22: PF3 26: PF7 30: PA3 3: PB13 7: PC7 11: PC11 15: PD12 19: PF0 23: PF4 27: PA0 31: PA4 0: PA1 4: PA5 8: PB14 12: PC8 16: PD9 20: PD13 24: PF1 28: PF5 1: PA2 5: PB11 9: PB15 13: PC9 17: PD10 21: PD14 25: PF2 29: PF6 2: PA3 6: PB12 10: PC6 14: PC10 18: PD11 22: PD15 26: PF3 30: PF7 3: PA4 7: PB13 11: PC7 15: PC11 19: PD12 23: PF0 27: PF4 31: PA0 0: PA0 4: PA4 8: PB13 12: PC7 16: PC11 20: PD12 24: PF0 28: PF4 1: PA1 5: PA5 9: PB14 13: PC8 17: PD9 21: PD13 25: PF1 29: PF5 2: PA2 6: PB11 10: PB15 14: PC9 18: PD10 22: PD14 26: PF2 30: PF6 3: PA3 7: PB12 11: PC6 15: PC10 19: PD11 23: PD15 27: PF3 31: PF7 0: PA2 4: PB11 8: PB15 12: PC9 16: PD10 20: PD14 24: PF2 28: PF6 1: PA3 5: PB12 9: PC6 13: PC10 17: PD11 21: PD15 25: PF3 29: PF7 2: PA4 6: PB13 10: PC7 14: PC11 18: PD12 22: PF0 26: PF4 30: PA0 3: PA5 7: PB14 11: PC8 15: PD9 19: PD13 23: PF1 27: PF5 31: PA1 0: PA3 4: PB12 8: PC6 12: PC10 16: PD11 20: PD15 24: PF3 28: PF7 1: PA4 5: PB13 9: PC7 13: PC11 17: PD12 21: PF0 25: PF4 29: PA0 2: PA5 6: PB14 10: PC8 14: PD9 18: PD13 22: PF1 26: PF5 30: PA1 3: PB11 7: PB15 11: PC9 15: PD10 19: PD14 23: PF2 27: PF6 31: PA2 0: PA4 4: PB13 8: PC7 12: PC11 16: PD12 20: PF0 24: PF4 28: PA0 1: PA5 5: PB14 9: PC8 13: PD9 17: PD13 21: PF1 25: PF5 29: PA1 2: PB11 6: PB15 10: PC9 14: PD10 18: PD14 22: PF2 26: PF6 30: PA2 3: PB12 7: PC6 11: PC10 15: PD11 19: PD15 23: PF3 27: PF7 31: PA3 0: PA5 4: PB14 8: PC8 12: PD9 16: PD13 20: PF1 24: PF5 28: PA1 1: PB11 5: PB15 9: PC9 13: PD10 17: PD14 21: PF2 25: PF6 29: PA2 2: PB12 6: PC6 10: PC10 14: PD11 18: PD15 22: PF3 26: PF7 30: PA3 3: PB13 7: PC7 11: PC11 15: PD12 19: PF0 23: PF4 27: PA0 31: PA4 0: PA1 4: PA5 8: PB14 12: PC8 16: PD9 20: PD13 24: PF1 28: PF5 1: PA2 5: PB11 9: PB15 13: PC9 17: PD10 21: PD14 25: PF2 29: PF6 2: PA3 6: PB12 10: PC6 14: PC10 18: PD11 22: PD15 26: PF3 30: PF7 3: PA4 7: PB13 11: PC7 15: PC11 19: PD12 23: PF0 27: PF4 31: PA0 silabs.com | Building a more connected world. 8 - 11 12 - 15 16 - 19 20 - 23 24 - 27 28 - 31 Description USART0 Request To Send hardware flow control output. USART0 Asynchronous Receive. USART0 Synchronous mode Master Input / Slave Output (MISO). USART0 Asynchronous Transmit. Also used as receive input in half duplex communication. USART0 Synchronous mode Master Output / Slave Input (MOSI). USART1 clock input / output. USART1 chip select input / output. USART1 Clear To Send hardware flow control input. USART1 Request To Send hardware flow control output. USART1 Asynchronous Receive. USART1 Synchronous mode Master Input / Slave Output (MISO). Rev. 1.6 | 191 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality US1_TX US2_CLK US2_CS US2_CTS US2_RTS US2_RX US2_TX LOCATION 0-3 4-7 8 - 11 12 - 15 16 - 19 20 - 23 0: PA0 4: PA4 8: PB13 1: PA1 5: PA5 2: PA2 12: PC7 16: PC11 20: PD12 24: PF0 28: PF4 9: PB14 13: PC8 17: PD9 21: PD13 25: PF1 29: PF5 6: PB11 10: PB15 14: PC9 18: PD10 22: PD14 26: PF2 30: PF6 3: PA3 7: PB12 11: PC6 15: PC10 19: PD11 23: PD15 27: PF3 31: PF7 0: PA7 4: PI1 8: PB7 12: PF0 16: PF5 20: PF9 24: PF13 28: PK1 1: PA8 5: PI2 9: PB8 13: PF1 17: PF6 21: PF10 25: PF14 29: PK2 2: PA9 6: PI3 10: PB9 14: PF3 18: PF7 22: PF11 26: PF15 30: PA5 3: PI0 7: PB6 11: PB10 15: PF4 19: PF8 23: PF12 27: PK0 31: PA6 0: PA8 4: PI2 8: PB8 12: PF1 16: PF6 20: PF10 24: PF14 28: PK2 1: PA9 5: PI3 9: PB9 13: PF3 17: PF7 21: PF11 25: PF15 29: PA5 2: PI0 6: PB6 10: PB10 14: PF4 18: PF8 22: PF12 26: PK0 30: PA6 3: PI1 7: PB7 11: PF0 15: PF5 19: PF9 23: PF13 27: PK1 31: PA7 0: PA9 4: PI3 8: PB9 12: PF3 16: PF7 20: PF11 24: PF15 28: PA5 1: PI0 5: PB6 9: PB10 13: PF4 17: PF8 21: PF12 25: PK0 29: PA6 2: PI1 6: PB7 10: PF0 14: PF5 18: PF9 22: PF13 26: PK1 30: PA7 3: PI2 7: PB8 11: PF1 15: PF6 19: PF10 23: PF14 27: PK2 31: PA8 0: PI0 4: PB6 8: PB10 12: PF4 16: PF8 20: PF12 24: PK0 28: PA6 1: PI1 5: PB7 9: PF0 13: PF5 17: PF9 21: PF13 25: PK1 29: PA7 2: PI2 6: PB8 10: PF1 14: PF6 18: PF10 22: PF14 26: PK2 30: PA8 3: PI3 7: PB9 11: PF3 15: PF7 19: PF11 23: PF15 27: PA5 31: PA9 0: PA6 4: PI0 8: PB6 12: PB10 16: PF4 20: PF8 24: PF12 28: PK0 1: PA7 5: PI1 9: PB7 13: PF0 17: PF5 21: PF9 25: PF13 29: PK1 2: PA8 6: PI2 10: PB8 14: PF1 18: PF6 22: PF10 26: PF14 30: PK2 3: PA9 7: PI3 11: PB9 15: PF3 19: PF7 23: PF11 27: PF15 31: PA5 0: PA5 4: PA9 8: PI3 12: PB9 16: PF3 20: PF7 24: PF11 28: PF15 1: PA6 5: PI0 9: PB6 13: PB10 17: PF4 21: PF8 25: PF12 29: PK0 2: PA7 6: PI1 10: PB7 14: PF0 18: PF5 22: PF9 26: PF13 30: PK1 3: PA8 7: PI2 11: PB8 15: PF1 19: PF6 23: PF10 27: PF14 31: PK2 silabs.com | Building a more connected world. 24 - 27 28 - 31 Description USART1 Asynchronous Transmit. Also used as receive input in half duplex communication. USART1 Synchronous mode Master Output / Slave Input (MOSI). USART2 clock input / output. USART2 chip select input / output. USART2 Clear To Send hardware flow control input. USART2 Request To Send hardware flow control output. USART2 Asynchronous Receive. USART2 Synchronous mode Master Input / Slave Output (MISO). USART2 Asynchronous Transmit. Also used as receive input in half duplex communication. USART2 Synchronous mode Master Output / Slave Input (MOSI). Rev. 1.6 | 192 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality US3_CLK US3_CS US3_CTS US3_RTS US3_RX US3_TX LOCATION 0-3 4-7 12 - 15 16 - 19 20 - 23 24 - 27 28 - 31 0: PD10 4: PD14 8: PB6 12: PB10 16: PC0 20: PC4 24: PF13 28: PK1 1: PD11 5: PD15 9: PB7 13: PB11 17: PC1 21: PC5 25: PF14 29: PK2 2: PD12 6: PI2 10: PB8 14: PJ14 18: PC2 22: PF11 26: PF15 30: PD8 3: PD13 7: PI3 11: PB9 15: PJ15 19: PC3 23: PF12 27: PK0 31: PD9 0: PD11 4: PD15 8: PB7 12: PB11 16: PC1 20: PC5 24: PF14 28: PK2 1: PD12 5: PI2 9: PB8 13: PJ14 17: PC2 21: PF11 25: PF15 29: PD8 2: PD13 6: PI3 10: PB9 14: PJ15 18: PC3 22: PF12 26: PK0 30: PD9 3: PD14 7: PB6 11: PB10 15: PC0 19: PC4 23: PF13 27: PK1 31: PD10 0: PD12 4: PI2 8: PB8 12: PJ14 16: PC2 20: PF11 24: PF15 28: PD8 1: PD13 5: PI3 9: PB9 13: PJ15 17: PC3 21: PF12 25: PK0 29: PD9 2: PD14 6: PB6 10: PB10 14: PC0 18: PC4 22: PF13 26: PK1 30: PD10 3: PD15 7: PB7 11: PB11 15: PC1 19: PC5 23: PF14 27: PK2 31: PD11 0: PD13 4: PI3 8: PB9 12: PJ15 16: PC3 20: PF12 24: PK0 28: PD9 1: PD14 5: PB6 9: PB10 13: PC0 17: PC4 21: PF13 25: PK1 29: PD10 2: PD15 6: PB7 10: PB11 14: PC1 18: PC5 22: PF14 26: PK2 30: PD11 3: PI2 7: PB8 11: PJ14 15: PC2 19: PF11 23: PF15 27: PD8 31: PD12 0: PD9 4: PD13 8: PI3 12: PB9 16: PJ15 20: PC3 24: PF12 28: PK0 1: PD10 5: PD14 9: PB6 13: PB10 17: PC0 21: PC4 25: PF13 29: PK1 2: PD11 6: PD15 10: PB7 14: PB11 18: PC1 22: PC5 26: PF14 30: PK2 3: PD12 7: PI2 11: PB8 15: PJ14 19: PC2 23: PF11 27: PF15 31: PD8 0: PD8 4: PD12 8: PI2 12: PB8 16: PJ14 20: PC2 24: PF11 28: PF15 1: PD9 5: PD13 9: PI3 13: PB9 17: PJ15 21: PC3 25: PF12 29: PK0 2: PD10 6: PD14 10: PB6 14: PB10 18: PC0 22: PC4 26: PF13 30: PK1 3: PD11 7: PD15 11: PB7 15: PB11 19: PC1 23: PC5 27: PF14 31: PK2 Description USART3 clock input / output. USART3 chip select input / output. USART3 Clear To Send hardware flow control input. USART3 Request To Send hardware flow control output. USART3 Asynchronous Receive. USART3 Synchronous mode Master Input / Slave Output (MISO). USART3 Asynchronous Transmit. Also used as receive input in half duplex communication. USART3 Synchronous mode Master Output / Slave Input (MOSI). 0: PA1 Digital to analog converter VDAC0 external reference input pin. 0: PA3 Digital to Analog Converter DAC0 output channel number 0. 0: PA5 Digital to Analog Converter DAC0 alternative output for channel 0. VDAC0_EXT VDAC0_OUT0 / OPA0_OUT VDAC0_OUT0AL T / OPA0_OUTALT 8 - 11 1: PD13 2: PD15 silabs.com | Building a more connected world. Rev. 1.6 | 193 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality LOCATION 0-3 4-7 8 - 11 12 - 15 16 - 19 20 - 23 24 - 27 28 - 31 0: PD14 Digital to Analog Converter DAC0 output channel number 1. 0: PD12 Digital to Analog Converter DAC0 alternative output for channel 1. VDAC0_OUT1 / OPA1_OUT VDAC0_OUT1AL T / OPA1_OUTALT WTIM0_CC0 WTIM0_CC1 WTIM0_CC2 WTIM0_CDTI0 WTIM0_CDTI1 WTIM0_CDTI2 WTIM1_CC0 Description 1: PA2 2: PA4 0: PA0 4: PA4 8: PA8 12: PB8 16: PB12 20: PC0 24: PC4 28: PC8 1: PA1 5: PA5 9: PA9 13: PB9 17: PB13 21: PC1 25: PC5 29: PC9 2: PA2 6: PA6 10: PB6 14: PB10 18: PB14 22: PC2 26: PC6 30: PC10 3: PA3 7: PA7 11: PB7 15: PB11 19: PB15 23: PC3 27: PC7 31: PC11 0: PA2 4: PA6 8: PB6 12: PB10 16: PB14 20: PC2 24: PC6 28: PC10 1: PA3 5: PA7 9: PB7 13: PB11 17: PB15 21: PC3 25: PC7 29: PC11 2: PA4 6: PA8 10: PB8 14: PB12 18: PC0 22: PC4 26: PC8 30: PD8 3: PA5 7: PA9 11: PB9 15: PB13 19: PC1 23: PC5 27: PC9 31: PD9 0: PA4 4: PA8 8: PB8 12: PB12 16: PC0 20: PC4 24: PC8 28: PD8 1: PA5 5: PA9 9: PB9 13: PB13 17: PC1 21: PC5 25: PC9 29: PD9 2: PA6 6: PB6 10: PB10 14: PB14 18: PC2 22: PC6 26: PC10 30: PD10 3: PA7 7: PB7 11: PB11 15: PB15 19: PC3 23: PC7 27: PC11 31: PD11 0: PA8 4: PB8 8: PB12 12: PC0 16: PC4 20: PC8 24: PD8 28: PD12 1: PA9 5: PB9 9: PB13 13: PC1 17: PC5 21: PC9 25: PD9 29: PD13 2: PB6 6: PB10 10: PB14 14: PC2 18: PC6 22: PC10 26: PD10 30: PD14 3: PB7 7: PB11 11: PB15 15: PC3 19: PC7 23: PC11 27: PD11 31: PD15 0: PB6 4: PB10 8: PB14 12: PC2 16: PC6 20: PC10 24: PD10 28: PD14 1: PB7 5: PB11 9: PB15 13: PC3 17: PC7 21: PC11 25: PD11 29: PD15 2: PB8 6: PB12 10: PC0 14: PC4 18: PC8 22: PD8 26: PD12 30: PF0 3: PB9 7: PB13 11: PC1 15: PC5 19: PC9 23: PD9 27: PD13 31: PF1 0: PB8 4: PB12 8: PC0 12: PC4 16: PC8 20: PD8 24: PD12 28: PF0 1: PB9 5: PB13 9: PC1 13: PC5 17: PC9 21: PD9 25: PD13 29: PF1 2: PB10 6: PB14 10: PC2 14: PC6 18: PC10 22: PD10 26: PD14 30: PF2 3: PB11 7: PB15 11: PC3 15: PC7 19: PC11 23: PD11 27: PD15 31: PF3 0: PB12 4: PC0 8: PC4 12: PC8 16: PD8 20: PD12 24: PF0 28: PF4 1: PB13 5: PC1 9: PC5 13: PC9 17: PD9 21: PD13 25: PF1 29: PF5 2: PB14 6: PC2 10: PC6 14: PC10 18: PD10 22: PD14 26: PF2 30: PF6 3: PB15 7: PC3 11: PC7 15: PC11 19: PD11 23: PD15 27: PF3 31: PF7 silabs.com | Building a more connected world. Wide timer 0 Capture Compare input / output channel 0. Wide timer 0 Capture Compare input / output channel 1. Wide timer 0 Capture Compare input / output channel 2. Wide timer 0 Complimentary Dead Time Insertion channel 0. Wide timer 0 Complimentary Dead Time Insertion channel 1. Wide timer 0 Complimentary Dead Time Insertion channel 2. Wide timer 1 Capture Compare input / output channel 0. Rev. 1.6 | 194 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Alternate Functionality WTIM1_CC1 WTIM1_CC2 WTIM1_CC3 LOCATION 0-3 4-7 0: PB14 4: PC2 1: PB15 12 - 15 16 - 19 20 - 23 8: PC6 12: PC10 16: PD10 20: PD14 24: PF2 28: PF6 5: PC3 9: PC7 13: PC11 17: PD11 21: PD15 25: PF3 29: PF7 2: PC0 6: PC4 10: PC8 14: PD8 18: PD12 22: PF0 26: PF4 30: PF8 3: PC1 7: PC5 11: PC9 15: PD9 19: PD13 23: PF1 27: PF5 31: PF9 0: PC0 4: PC4 8: PC8 12: PD8 16: PD12 20: PF0 24: PF4 28: PF8 1: PC1 5: PC5 9: PC9 13: PD9 17: PD13 21: PF1 25: PF5 29: PF9 2: PC2 6: PC6 10: PC10 14: PD10 18: PD14 22: PF2 26: PF6 30: PF10 3: PC3 7: PC7 11: PC11 15: PD11 19: PD15 23: PF3 27: PF7 31: PF11 0: PC2 4: PC6 8: PC10 12: PD10 16: PD14 20: PF2 24: PF6 28: PF10 1: PC3 5: PC7 9: PC11 13: PD11 17: PD15 21: PF3 25: PF7 29: PF11 2: PC4 6: PC8 10: PD8 14: PD12 18: PF0 22: PF4 26: PF8 30: PF12 3: PC5 7: PC9 11: PD9 15: PD13 19: PF1 23: PF5 27: PF9 31: PF13 silabs.com | Building a more connected world. 8 - 11 24 - 27 28 - 31 Description Wide timer 1 Capture Compare input / output channel 1. Wide timer 1 Capture Compare input / output channel 2. Wide timer 1 Capture Compare input / output channel 3. Rev. 1.6 | 195 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions 6.9 Analog Port (APORT) Client Maps The Analog Port (APORT) is an infrastructure used to connect chip pins with on-chip analog clients such as analog comparators, ADCs, DACs, etc. The APORT consists of a set of shared buses, switches, and control logic needed to configurably implement the signal routing. Figure 6.7 APORT Connection Diagram on page 196 shows the APORT routing for this device family (note that available features may vary by part number). A complete description of APORT functionality can be found in the Reference Manual. ACMP0X ACMP0Y ADC0X ADC0Y DY DX CY CX PC6 PC7 PC8 PC9 PC10 PJ14 PC11 PC0 PJ15 PC1 PC2 PC3 PC4 PC5 1X IDAC0 ACMP1X ACMP1Y PF0 POS PF1 PF2 PF3 ACMP1 PF8 NEG PF9 PF10 POS NEG 0Y 1Y 2Y 3Y 4Y NEXT1 PF13 PF14 ADC0 PF15 PK0 PK1 0Y 1Y 2Y 3Y 4Y NEXT1 NEXT0 0X 1X 2X 3X 4X NEXT0 NEXT2 PF11 PF12 0X 1X 2X 3X 4X NEXT1 NEXT0 0X 1X 2X 3X 4X NEXT1 NEXT0 0Y 1Y 2Y 3Y 4Y NEXT1 NEXT0 1Y PB15 PB14 POS PB13 OPA2_N ACMP0 PB12 OUT2 NEG PB11 OPA2_P VDAC0_OPA2ALT VDAC0_OPA2ALT OUT2ALT OUT2ALT PB9 PB8 PB7 PB6 PI3 PI2 EXTP EXTN PK2 PF4 PF5 POS OPA0_P 1X 2X 3X 4X NEG OPA0_N 1Y 2Y 3Y 4Y PF6 PF7 AX AY BX BY OPA0 OUT OUT0 OUT0ALT OUT1 OUT2 OUT3 OUT4 NEXT0 POS OPA2_P 1X 2X 3X 4X NEG OPA2_N 1Y 2Y 3Y 4Y OPA2 PB10 PI1 OPA1_P 1X 2X 3X 4X POS OPA1_N 1Y 2Y 3Y 4Y NEG OUT1 OUT1ALT OUT1 OUT2 OUT3 OUT4 NEXT1 PI0 PA9 PA8 PA7 LESENSE OPA1 PA6 LESENSE OUT OUT0ALT OUT1ALT VDAC0_OUT0ALT VDAC0_OUT1ALT OPA0_N OPA0_INN0 PA5 LESENSE PA4 LESENSE OUT0 OUT1ALT OPA0_OUT VDAC0_OUT1ALT OPA0_P OPA0_INP0 PA3 LESENSE PA2 LESENSE ADC_EXTP ADC_EXTN OUT0ALT ADC0_EXTP ADC0_EXTN PA1 LESENSE PA0 LESENSE OPA0ALT PD15 LESENSE BUSADC0X, BUSADC0Y ACMP0X, ACMP1Y, ... BUSACMP0X, BUSACMP1Y, ... CEXT_SENSE 2X 2Y 4X 4Y VDAC0_OUT1ALT OPA1_OUT ADC0X, ADC0Y OPA1_INN0 OUT1 BUSAX, BUSBY, ... CSEN VDAC0_OUT0ALT OPA1_INP0 AX, BY, ... ALT0OUT OPA1_P APORTnX, APORTnY OPA1N 1X 1Y 3X 3Y CEXT nX, nY OUT2 OUT2ALT OUT1 OUT2 OUT3 OUT4 NEXT2 ALT1OUT OUT PD14 LESENSE PD13 LESENSE PD11 LESENSE PD12 LESENSE PD9 LESENSE PD10 LESENSE PD8 LESENSE Figure 6.7. APORT Connection Diagram Client maps for each analog circuit using the APORT are shown in the following tables. The maps are organized by bus, and show the peripheral's port connection, the shared bus, and the connection from specific bus channel numbers to GPIO pins. In general, enumerations for the pin selection field in an analog peripheral's register can be determined by finding the desired pin connection in the table and then combining the value in the Port column (APORT__), and the channel identifier (CH__). For example, if pin silabs.com | Building a more connected world. Rev. 1.6 | 196 silabs.com | Building a more connected world. PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSDY PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 PB15 PB13 BUSCY BUSDX PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSCX PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSBY PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSBX PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSAY PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSAX APORT4Y APORT4X APORT3Y APORT3X APORT2Y APORT2X APORT1Y APORT1X APORT0X Port PA8 PA9 PA8 PA9 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27 CH28 CH29 CH30 CH31 BUSACMP0Y BUSACMP0X Bus APORT0Y EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions PF7 is available on port APORT2X as CH23, the register field enumeration to connect to PF7 would be APORT2XCH23. The shared bus used by this connection is indicated in the Bus column. Table 6.9. ACMP0 Bus and Pin Mapping Rev. 1.6 | 197 silabs.com | Building a more connected world. PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSDY PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 PB15 PB13 BUSCY BUSDX PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSCX PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSBY PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSBX PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSAY PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSAX APORT4Y APORT4X APORT3Y APORT3X APORT2Y APORT2X APORT1Y APORT1X APORT0X Port PJ14 PJ15 PJ14 PJ15 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27 CH28 CH29 CH30 CH31 BUSACMP1Y BUSACMP1X Bus APORT0Y EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Table 6.10. ACMP1 Bus and Pin Mapping Rev. 1.6 | 198 silabs.com | Building a more connected world. PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSDY PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 PB15 PB13 BUSCY BUSDX PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSCX PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSBY PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSBX PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSAY PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSAX APORT4Y APORT4X APORT3Y APORT3X APORT2Y APORT2X APORT1Y APORT1X APORT0X Port PI0 PI1 PI2 PI3 PI0 PI1 PI2 PI3 CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27 CH28 CH29 CH30 CH31 BUSADC0Y BUSADC0X Bus APORT0Y EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Table 6.11. ADC0 Bus and Pin Mapping Rev. 1.6 | 199 silabs.com | Building a more connected world. PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 BUSCY PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSCX CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27 CH28 CH29 CH30 CH31 Bus APORT1Y APORT1X Port PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSDY PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 BUSDX PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSBY PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSBX APORT4Y APORT4X APORT2Y APORT2X PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 BUSCY PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSCX PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSAY PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSAX APORT3Y APORT3X APORT1Y APORT1X CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27 CH28 CH29 CH30 CH31 Bus Port EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Table 6.12. CSEN Bus and Pin Mapping CEXT CEXT_SENSE Table 6.13. IDAC0 Bus and Pin Mapping Rev. 1.6 | 200 silabs.com | Building a more connected world. PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 BUSDX PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSCX PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSBX PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSAX APORT4X APORT3X APORT2X APORT1X PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSDY PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 BUSCY PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSBY PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSAY APORT4Y APORT3Y APORT2Y APORT1Y CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27 CH28 CH29 CH30 CH31 Bus Port EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions Table 6.14. VDAC0 / OPA Bus and Pin Mapping OPA0_N OPA0_P Rev. 1.6 | 201 silabs.com | Building a more connected world. PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSDY PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 BUSCY PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSBY PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSAY APORT4Y APORT3Y APORT2Y APORT1Y PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 BUSDX PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSCX PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSBX PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSAX APORT4X APORT3X APORT2X APORT1X PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSDY PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 BUSCY PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSBY PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSAY APORT4Y APORT3Y APORT2Y APORT1Y CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27 CH28 CH29 CH30 CH31 Bus Port EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions OPA1_N OPA1_P OPA2_N Rev. 1.6 | 202 silabs.com | Building a more connected world. PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSDY PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 BUSCY PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSBY PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSAY APORT4Y APORT3Y APORT2Y APORT1Y PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 BUSDX PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSCX PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSBX PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSAX APORT4X APORT3X APORT2X APORT1X PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSDY PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 BUSCY PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSBY PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSAY APORT4Y APORT3Y APORT2Y APORT1Y CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27 CH28 CH29 CH30 CH31 Bus Port EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions OPA2_OUT OPA2_P VDAC0_OUT0 / OPA0_OUT Rev. 1.6 | 203 silabs.com | Building a more connected world. PD8 PD10 PD12 PD14 PA0 PA2 PA4 PA6 PB6 PB8 PB10 PB12 PB14 BUSDY PD9 PD11 PD13 PD15 PA1 PA3 PA5 PA7 PB7 PB9 PB11 PB13 PB15 BUSCY PC0 PC2 PC4 PC6 PC8 PC10 PF0 PF2 PF4 PF6 PF8 PF10 PF12 PF14 BUSBY PC1 PC3 PC5 PC7 PC9 PC11 PF1 PF3 PF5 PF7 PF9 PF11 PF13 PF15 BUSAY APORT4Y APORT3Y APORT2Y APORT1Y CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 CH16 CH17 CH18 CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27 CH28 CH29 CH30 CH31 Bus Port EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Pin Definitions VDAC0_OUT1 / OPA1_OUT Rev. 1.6 | 204 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet BGA125 Package Specifications 7. BGA125 Package Specifications 7.1 BGA125 Package Dimensions Figure 7.1. BGA125 Package Drawing silabs.com | Building a more connected world. Rev. 1.6 | 205 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet BGA125 Package Specifications Table 7.1. BGA125 Package Dimensions Dimension Min Typ Max A 0.80 0.87 0.94 A1 0.16 0.21 0.26 A2 0.61 0.66 0.71 c 0.17 0.21 0.25 D 6.90 7.00 7.10 E 6.90 7.00 7.10 D1 -- 6.00 -- E1 -- 6.00 -- e -- 0.50 -- b 0.25 0.30 0.35 aaa 0.10 bbb 0.10 ddd 0.08 eee 0.15 fff 0.05 Note: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. silabs.com | Building a more connected world. Rev. 1.6 | 206 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet BGA125 Package Specifications 7.2 BGA125 PCB Land Pattern Figure 7.2. BGA125 PCB Land Pattern Drawing silabs.com | Building a more connected world. Rev. 1.6 | 207 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet BGA125 Package Specifications Table 7.2. BGA125 PCB Land Pattern Dimensions Dimension Min Nom X 0.25 C1 6.00 C2 6.00 E1 0.5 E2 0.5 Max Note: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This Land Pattern Design is based on the IPC-7351 guidelines. 4. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 m minimum, all the way around the pad. 5. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 6. The stencil thickness should be 0.125 mm (5 mils). 7. The ratio of stencil aperture to land pad size should be 1:1. 8. A No-Clean, Type-3 solder paste is recommended. 9. The recommended card reflow profile is per the JEDEC/IPC J-STD-020C specification for Small Body Components. silabs.com | Building a more connected world. Rev. 1.6 | 208 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet BGA125 Package Specifications 7.3 BGA125 Package Marking EFR32 PPPPPPPPPP YYWWTTTTTT Figure 7.3. BGA125 Package Marking The package marking consists of: * PPPPPPPPP - The part number designation. 1. Family Code (B | M | F) 2. G (Gecko) 3. Series (1, 2,...) 4. Device Configuration (1, 2,...) 5. Performance Grade (P | B | V) 6. Feature Code (1, 2,...) 7. TRX Code (3 = TXRX | 2= RX | 1 = TX) 8. Band (1 = Sub-GHz | 2 = 2.4 GHz | 3 = Dual-band) 9. Flash (J = 1024K | H = 512K | G = 256K | F = 128K | E = 64K | D = 32K) 10. Temperature Grade (G = -40 to 85 | I = -40 to 125) * YY - The last 2 digits of the assembly year. * WW - The 2-digit workweek when the device was assembled. * TTTTTT - A trace or manufacturing code. The first letter is the device revision. silabs.com | Building a more connected world. Rev. 1.6 | 209 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet QFN48 Package Specifications 8. QFN48 Package Specifications 8.1 QFN48 Package Dimensions Figure 8.1. QFN48 Package Drawing silabs.com | Building a more connected world. Rev. 1.6 | 210 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet QFN48 Package Specifications Table 8.1. QFN48 Package Dimensions Dimension Min Typ Max A 0.80 0.85 0.90 A1 0.00 0.02 0.05 A3 0.20 REF b 0.18 0.25 0.30 D 6.90 7.00 7.10 E 6.90 7.00 7.10 D2 5.15 5.30 5.45 E2 5.15 5.30 5.45 e 0.50 BSC L 0.30 0.40 0.50 K 0.20 -- -- R 0.09 -- -- aaa 0.15 bbb 0.10 ccc 0.10 ddd 0.05 eee 0.08 fff 0.10 Note: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to the JEDEC Solid State Outline MO-220, Variation VKKD-4. 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. silabs.com | Building a more connected world. Rev. 1.6 | 211 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet QFN48 Package Specifications 8.2 QFN48 PCB Land Pattern Figure 8.2. QFN48 PCB Land Pattern Drawing silabs.com | Building a more connected world. Rev. 1.6 | 212 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet QFN48 Package Specifications Table 8.2. QFN48 PCB Land Pattern Dimensions Dimension Typ S1 6.01 S 6.01 L1 4.70 W1 4.70 e 0.50 W 0.26 L 0.86 Note: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. This Land Pattern Design is based on the IPC-7351 guidelines. 3. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 m minimum, all the way around the pad. 4. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 5. The stencil thickness should be 0.125 mm (5 mils). 6. The ratio of stencil aperture to land pad size can be 1:1 for all perimeter pads. 7. A 4x4 array of 0.75 mm square openings on a 1.00 mm pitch can be used for the center ground pad. 8. A No-Clean, Type-3 solder paste is recommended. 9. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. silabs.com | Building a more connected world. Rev. 1.6 | 213 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet QFN48 Package Specifications 8.3 QFN48 Package Marking EFR32 PPPPPPPPPP YYWWTTTTTT Figure 8.3. QFN48 Package Marking The package marking consists of: * PPPPPPPPP - The part number designation. 1. Family Code (B | M | F) 2. G (Gecko) 3. Series (1, 2,...) 4. Device Configuration (1, 2,...) 5. Performance Grade (P | B | V) 6. Feature Code (1, 2,...) 7. TRX Code (3 = TXRX | 2 = RX | 1 = TX) 8. Band (1 = Sub-GHz | 2 = 2.4 GHz | 3 = Dual-band) 9. Flash (J = 1024K | H = 512K | G = 256K | F = 128K | E = 64K | D = 32K) 10. Temperature Grade (G = -40 to 85 | I = -40 to 125) * YY - The last 2 digits of the assembly year. * WW - The 2-digit workweek when the device was assembled. * TTTTTT - A trace or manufacturing code. The first letter is the device revision. silabs.com | Building a more connected world. Rev. 1.6 | 214 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet QFN68 Package Specifications 9. QFN68 Package Specifications 9.1 QFN68 Package Dimensions Figure 9.1. QFN68 Package Drawing silabs.com | Building a more connected world. Rev. 1.6 | 215 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet QFN68 Package Specifications Table 9.1. QFN68 Package Dimensions Dimension Min Typ Max A 0.80 0.85 0.90 A1 0.00 0.02 0.05 A3 0.20 REF b 0.15 0.20 0.25 D 7.90 8.00 8.10 E 7.90 8.00 8.10 D2 6.05 6.20 6.35 E2 6.05 6.20 6.35 e 0.40 BSC L 0.30 0.40 0.50 K 0.20 -- -- R 0.075 -- -- aaa 0.10 bbb 0.07 ccc 0.10 ddd 0.05 eee 0.08 fff 0.10 Note: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to the JEDEC Solid State Outline MO-220, Variation VKKD-4. 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. silabs.com | Building a more connected world. Rev. 1.6 | 216 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet QFN68 Package Specifications 9.2 QFN68 PCB Land Pattern Figure 9.2. QFN68 PCB Land Pattern Drawing silabs.com | Building a more connected world. Rev. 1.6 | 217 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet QFN68 Package Specifications Table 9.2. QFN68 PCB Land Pattern Dimensions Dimension Typ L 0.86 W 0.22 e 0.40 S 7.01 S1 7.01 L1 6.35 W1 6.35 Note: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. This Land Pattern Design is based on the IPC-7351 guidelines. 3. All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition (LMC) is calculated based on a Fabrication Allowance of 0.05mm. 4. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 m minimum, all the way around the pad. 5. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 6. The stencil thickness should be 0.100 mm (4 mils). 7. The ratio of stencil aperture to land pad size can be 1:1 for all pads. 8. A 3x3 array of 1.50 mm square openings on a 1.80 mm pitch can be used for the center ground pad. 9. A No-Clean, Type-3 solder paste is recommended. 10. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. silabs.com | Building a more connected world. Rev. 1.6 | 218 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet QFN68 Package Specifications 9.3 QFN68 Package Marking EFR32 PPPPPPPPPP YYWWTTTTTT Figure 9.3. QFN68 Package Marking The package marking consists of: * PPPPPPPPPP - The part number designation. * TTTTTT - A trace or manufacturing code. The first letter is the device revision. * YY - The last 2 digits of the assembly year. * WW - The 2-digit workweek when the device was assembled. silabs.com | Building a more connected world. Rev. 1.6 | 219 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Revision History 10. Revision History Revision 1.6 September, 2020 * Updated External PA supply connection conditions for SPURHARM_ETSI and SPUROOB_ETSI in section 4.1.10.3 Sub-GHz RF Transmitter characteristics for 868 MHz Band. Revision 1.5 December, 2019 * In the front page block diagram, updated the lowest energy mode for LETIMER. * Updated 3.6.4 Low Energy Timer (LETIMER) lowest energy mode. * In 5.2 RF Matching Networks, corrected document references for component values and added document reference to IPD solutions. * Corrected the max value of the Absolute voltage on 2G4RF_IOP, 2G4RF_ION, SUBGRF_OP and SUBGRF_ON pins in Absolute Maximum Ratings table in 4.1.1 Absolute Maximum Ratings. * Added a Note about the operating voltage in 3.8.3 True Random Number Generator (TRNG). silabs.com | Building a more connected world. Rev. 1.6 | 220 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Revision History Revision 1.41 July, 2019 * In Feature List, removed wake on radio. * In Electrical Specifications, reordered footnotes according to order of appearance in the table. * In General Operating Conditions for fCORE : * Added conditions for all usable wait state settings * Corrected maximum specification from 20 MHz to 7 MHz for test condition VSCALE0, MODE = WS0 * In sub-GHz specifications, replaced references to "PAVDD" with "External PA Supply" for clarity. * In RF Transmitter Characteristics for 802.15.4 DSSS-OQPSK in the 2.4GHz Band, updated parameter for EVM. * In Sub-GHz RF Transmitter characteristics for 915 MHz Band: * Corrected test conditions for: * SPURHARM_FCC_14, in non-restricted bands * SPUROOB_FCC_14, in non-restricted bands * SPURHARM_FCC_20, in non-restricted bands * SPUROOB_FCC_20, in non-restricted bands * Updated typical specification from -52 dBm to -62 dBm and maximum specification from -46 dBm to -56 dBm for: * SPUROOB_FCC_20, in restricted bands (30-88 MHz) * SPUROOB_FCC_14, in restricted bands (30-88 MHz) * Added footnote to PSD. * In 4.1.10.2 Sub-GHz RF Receiver Characteristics for 915 MHz Band, updated typical specification from -60 dBm to -61 dBm and maximum specification from -54 dBm to -55 dBm for SPURRX_ARIB, 930-1000 MHz, RBW=100 kHz. * Corrected units for FRANGE in: * Sub-GHz RF Receiver Characteristics for 490 MHz Band * Sub-GHz RF Receiver Characteristics for 315 MHz Band * Sub-GHz RF Receiver Characteristics for 169 MHz Band * In LFRCO, updated test conditions for fLFRCO. * In GPIO, added footnotes to VIL and VIH. * In VMON, updated test conditions for IVMON. * In VDAC, updated test conditions for IDAC, 200 Hz refresh rate. * In CSEN, updated test conditions for: * CEXTMAX * ICSEN_BOND * ICSEN_EM2 * ICSEN_ACTIVE * In Pin Definitions, updated pin descriptions for DECOUPLE and RESETn. * In 7.3 BGA125 Package Marking, updated feature code. * In 8.3 QFN48 Package Marking, updated feature code. Revision 1.4 June, 2019 * Added new orderable part numbers for QFN68 I-grade variants * System Overview Sections: Minor wording and typographical error fixes silabs.com | Building a more connected world. Rev. 1.6 | 221 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Revision History Revision 1.3 June, 2018 * * * * * * Added new orderable part numbers for QFN68 variants and associated packaging, pinout, and electrical specifications. Table 3.2 Configuration Summary on page 20: Corrected listed features for USART1 and USART3. : Added footnote to clarify IOVDD over-voltage operation conditions. 4.1.5.4 Current Consumption Using Radio 3.3 V with DC-DC: Updated typical 802.15.4 receive current specifications. Table 6.7 GPIO Functionality Table on page 138: Changed presentation to order table by pin name instead of pin location. Figure 6.7 APORT Connection Diagram on page 196: Corrected OPA output connections to route through "Y" buses. silabs.com | Building a more connected world. Rev. 1.6 | 222 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Revision History Revision 1.1 October, 2017 * * * * Updated Ordering Table to revision-C OPNs. Added high-temperature part numbers to Ordering Table and added associated specifications / content throughout document. Updated product highlights on Front Page and Feature List for consistency across EFR32xG1x family documentation. System Overview Updates * Expanded Receiver Architecture section. * Clarified / corrected energy mode mentions in RTCC and Opamp sections. * Memory maps updated with LE peripherals and new formatting. * Absolute Maximum Ratings Table: * Removed redundant IVSSMAX line. * Added footnote to clarify VDIGPIN specification for 5V tolerant GPIO. * General Operating Conditions Table: * Removed redundant footnote about shorting VREGVDD and AVDD together. * Added footnote about IOVDD voltage restriction when CSEN peripheral is used with chopping enabled. * Added footnote for additional information on peak current during voltage scaling operations. * RF Receiver Characteristics for Bluetooth Low Energy in the 2.4GHz Band, 1 Mbps Data Rate Table: * Sensitivity, Co-channel interferer and Selectivity typical numbers updated to latest phy characterization data. * BLOCKOOB specifications changed to show Min values instead of Typ. * RF Receiver Characteristics for Bluetooth Low Energy in the 2.4GHz Band, 2 Mbps Data Rate Table: * SAT Typical value corrected from 5 to 10 dBm. * BLOCKOOB specifications removed (not part of BLE 2 Mbps specification). * RF Receiver Characteristics for 802.15.4 DSSS-OQPSK in the 2.4 GHz Band Table: Footnote added to BLOCK80211G specification to clarify blocker signal definition. * Sub-GHz RF Receiver Characteristics for 915 MHz Band Table: Added O-QPSK DSSS phy specifications. * Sub-GHz RF Transmitter Characteristics for 868 MHz Band Table: SPUROOB_ETSI below 1 GHz Typ corrected from -60 to -42 dBm. * Sub-GHz RF Receiver Characteristics for 490 MHz Band Table: Corrected 10 kbps 2GFSK reference signal bandwidth to 20.038 kHz. * Flash Memory Characteristics Table: * Added timing measurement clarification for Device Erase and Mass Erase. * Device Erase Time typical values corrected from 69 to 82 ms. * Analog to Digital Converter (ADC) Table: * Added header text for general specification conditions. * Added footnote for clarification of input voltage limits. * Digital to Analog Converter (VDAC) Table: Gain Error min/max specifications relaxed for REFSEL on 1V25LN, VDD, and EXT settings. * Current Digital to Analog Converter (IDAC) Table: Total accuracy STEPSEL value setting corrected from 0x80 to 0x10. * Analog Port (APORT) Table: Operation in EM2/EM3 supply current changed from 915 to 67 nA (silicon fix from rev B to C). * 2.4 GHz RF Transmitter Output Power Figure: Extended temperature range to 125 C. * 2.4 GHz RF Receiver Sensitivity Figure: Updated with latest characterization data and added 125 C operational plots. * Typical Sub-GHz Impedance-matching network circuits Figure: Corrected split between two examples from 450 MHz to 500 MHz. * Minor typographical corrections, including capitalization, mis-spellings and punctuation marks, throughout document. * Minor formatting and styling updates, including table formats, TOC location, and boilerplate information throughout document. silabs.com | Building a more connected world. Rev. 1.6 | 223 EFR32BG12 Gecko Bluetooth (R)Low Energy SoC Family Data Sheet Revision History Revision 1.0 2017-04-14 * * * * * Added Thermal Characteristics table. Finalized specification tables. All tables were updated with latest characterization data and production test limits. Updated typical performance graphs for DC-DC. Minor typographical, clarity, and consistency improvements. Condensed pin function tables with new formatting. Revision 0.6 2017-02-23 * Updated 2 Mbps BLE receiver specifications with latest characteriztion data. * Added table-wide conditions to BLE 1 Mbps and 2 Mbps receiver tables. * Clarified opamp noise measurement conditions in electrical spec table. Revision 0.5 2017-02-03 * * * * * * * * * * * * New corporate stylesheet applied. Updated device block diagrams on front page and in System Overview. Updated Feature List with latest characterization numbers. "Bluetooth Smart" changed to "Bluetooth Low Energy" throughout document. All OPNs changed to revision B. Minor typographical corrections and clarifications in System Overview. Electrical Characteristics Table Changes * All specification tables updated with latest characterization data and production test limits. * Split 2.4 GHz BLE tables into separate tables for 1 Mbps and 2 Mbps data rates. * Split HFRCO/AUXHFRCO table into separate tables for HFRCO and AUXHFRCO. * OPAMP, CSEN, and VDAC specification line items updated to match test conditions. * Added tables for Analog Port (APORT) and Pulse Counter (PCNT). Added Typical Performance Curves for supply current, DCDC, and RF parameters. Added missing alternate functions and descriptions to Pinout and Alternate Function tables. Added APORT Connection Diagram. Corrected Package Marking description for QFN48 and BGA125. Corrected Package Marking diagram for QFN48. Revision 0.2 2016-09-21 Initial release. silabs.com | Building a more connected world. Rev. 1.6 | 224 Simplicity Studio One-click access to MCU and wireless tools, documentation, software, source code libraries & more. Available for Windows, Mac and Linux! SW/HW IoT Portfolio www.silabs.com/IoT www.silabs.com/simplicity Quality www.silabs.com/quality Support & Community www.silabs.com/community Disclaimer Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes without further notice to the product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Without prior notification, Silicon Labs may update product firmware during the manufacturing process for security or reliability reasons. Such changes will not alter the specifications or the performance of the product. Silicon Labs shall have no liability for the consequences of use of the information supplied in this document. This document does not imply or expressly grant any license to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any FDA Class III devices, applications for which FDA premarket approval is required, or Life Support Systems without the specific written consent of Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs products shall under no circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Silicon Labs disclaims all express and implied warranties and shall not be responsible or liable for any injuries or damages related to use of a Silicon Labs product in such unauthorized applications. Trademark Information Silicon Laboratories Inc.(R), Silicon Laboratories(R), Silicon Labs(R), SiLabs(R) and the Silicon Labs logo(R), Bluegiga(R), Bluegiga Logo(R), ClockBuilder(R), CMEMS(R), DSPLL(R), EFM(R), EFM32(R), EFR, Ember(R), Energy Micro, Energy Micro logo and combinations thereof, "the world's most energy friendly microcontrollers", Ember(R), EZLink(R), EZRadio(R), EZRadioPRO(R), Gecko(R), Gecko OS, Gecko OS Studio, ISOmodem(R), Precision32(R), ProSLIC(R), Simplicity Studio(R), SiPHY(R), Telegesis, the Telegesis Logo(R), USBXpress(R), Zentri, the Zentri logo and Zentri DMS, Z-Wave(R), and others are trademarks or registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited. Wi-Fi is a registered trademark of the Wi-Fi Alliance. All other products or brand names mentioned herein are trademarks of their respective holders. Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 USA http://www.silabs.com