Compact Pre-wired Photomicrosensor with Built-in Amplifier (Non-modulated) EE-SX91 CSM_EE-SX91_DS_E_3_1 Meeting Customer Needs with Compact Sensors that Mount with M3 Screws * Both light-ON and dark-ON outputs provided. * A compact size and choice of five models for a wide range of applications. * Compact NPN and PNP output models. * Mount using M3 or M2 screws. * Indicator is visible in many directions for installation in any location. * Maximum load current of 100 mA. * Models with connectors simplify wiring and maintenance. * Flexible robot cables are standard on all models. Be sure to read Safety Precautions on page 6. Features A Compact Size and Choice of Five Models for a Wide Range of Applications Flexible Robot Cables: Standard on All Models Select any of five models to minimize the space required. Robot Cables are effective for moving parts, and are provided as standard equipment with all models. Both Light-ON and Dark-ON Outputs Both light-ON and dark-ON outputs are provided on all models, allowing outputs to be switched by simply changing the wiring according to the application. Indicator Visible from Many Directions for Installation in Any Location Compact NPN and PNP Output Models The light indicator can be checked from up to four directions. Both NPN and PNP output models are available for use according to system requirements. Maximum Load Current of 100 mA Output control of up to 100 mA is supported for either NPN or PNP outputs. Models with Connectors Simplify Wiring and Maintenance Using models with connectors allows wiring to be used as it is, with no need to replace anything but sensors. Mount Using M3 or M2 Screws The EE-SX91 can be mounted using M3 or M2 screws, so it can easily replace an existing compact sensor mounted with M2 screws. 1 EE-SX91 Ordering Information List of Models Models with Robot Cables Appearance Sensing method Infrared light Sensing distance Output configuration Indicator mode Standard L-shaped F-shaped Throughbeam type (with slot) 5 mm (slot width) Light-ON Dark-ON (2 outputs) Lit when light is incident R-shaped U-shaped Connecting method (Cable length) Model NPN output PNP output Pre-wired models (1 m) EE-SX910-R 1M Models with connectors (0.3 m) EE-SX910-C1J-R 0.3M EE-SX910P-C1J-R 0.3M Pre-wired models (1 m) EE-SX911-R 1M Models with connectors (0.3 m) EE-SX911-C1J-R 0.3M EE-SX911P-C1J-R 0.3M Pre-wired models (1 m) EE-SX912-R 1M Models with connectors (0.3 m) EE-SX912-C1J-R 0.3M EE-SX912P-C1J-R 0.3M Pre-wired models (1 m) EE-SX913-R 1M Models with connectors (0.3 m) EE-SX913-C1J-R 0.3M EE-SX913P-C1J-R 0.3M Pre-wired models (1 m) E-SX914-R 1M Models with connectors (0.3 m) EE-SX914-C1J-R 0.3M EE-SX914P-C1J-R 0.3M EE-SX910P-R 1M EE-SX911P-R 1M EE-SX912P-R 1M EE-SX913P-R 1M EE-SX914P-R 1M Accessories (Order Separately) Connector with Robot Cable Type Connector with Cable Cable length 2m Model EE-1016-R Remarks Connector with lock, AWG26, 4-core Robot Cable 2 EE-SX91 Ratings and Specifications Type Item Standard L-shaped F-shaped R-shaped U-shaped NPN models Pre-wired models EE-SX910-R EE-SX911-R EE-SX912-R EE-SX913-R EE-SX914-R Models with connectors EE-SX911-C1J-R EE-SX912-C1J-R EE-SX913-C1J-R EE-SX914-C1J-R PNP models Pre-wired models EE-SX910P-R EE-SX911P-R EE-SX912P-R EE-SX913P-R EE-SX914P-R Models with connectors EE-SX910-C1J-R EE-SX910P-C1J-R EE-SX911P-C1J-R EE-SX912P-C1J-R EE-SX913P-C1J-R EE-SX914P-C1J-R Sensing distance 5 mm (slot width) Sensing object Opaque: 1.2 x 0.8 mm min. Differential distance 0.025 mm max. Light source GaAs infrared LED with a peak wavelength of 940 nm Indicator Light indicator (red LED) Supply voltage 5 to 24 VDC 10%, ripple (p-p): 10% max. Current consumption 15 mA max. Control output Load power supply voltage: 5 to 24 VDC Load current: 100 mA max. OFF current: 0.5 mA max. 100 mA load current with a residual voltage of 1.0 V max. 5 mA load current with a residual voltage of 0.4 V max. Protection circuits Power supply reverse polarity protection; output reverse polarity protection Response frequency 3 kHz min. (8 kHz average) Light incident: 15 s average; light interrupted: 40 s average* Ambient illumination 1,000 lx max. with fluorescent light on the surface of the receiver Ambient temperature range Operating: -25 to 55C Storage: -30 to 80C (with no icing or condensation) Ambient humidity range Operating: 5% to 85% Storage: 5% to 95% (with no icing or condensation) Vibration resistance (Destruction) 10 to 2,000 Hz 0.75-mm single amplitude for 2.5 h (15-min periods, 10 cycles) each in X, Y, and Z directions Shock resistance (Destruction) 500 m/s2 for 3 times each in X, Y, and Z directions Degree of protection IEC60529 IP50 Connecting method Pre-wired Models (standard cable length: 1 m), Models with Connectors (standard cable length: 0.3 m) Pre-wired Models Approx. 17 g Weight (packed state) Models with Con- Approx. 7 g nectors Mate- Case/cover rials Emitter/receiver Polybutylene phthalate (PBT) Polycarbonate (PC) Applicable Connector Product Connector with Robot Cable Model EE-1016-R * The response frequency was measured by detecting the following rotating disk. The response times for light incidence and light interruption are shown in the timing chart. Disk Appearance Item Contact resistance Insertion strength Surplus strength (housing holding strength) Cable length Ambient temperature range Mate- Housing rials Contact 2 mm 1 mm 25 m max. (at 10 mA DC and 20 mV max.) 20 N max. 2 mm t=0.2 mm Light incident Light interrupted 15 N min. 2m -25 to 85C Nylon Phosphor bronze OUT1 output ON OFF transistor OUT2 output ON OFF transistor 15 s avg. 40 s avg. 3 EE-SX91 Engineering Data (Typical) Sensing Position Characteristics EE-SX910 EE-SX910 Dark-ON Dark-ON EE-SX911 Dark-ON d Insertion direction Insertion direction Insertion direction d d Light-ON Light-ON 0 1 2 3 4 5 6 0 1 2 Distance d (mm) 3 4 5 6 Distance d (mm) Light-ON 0 1 2 3 4 5 6 Distance d (mm) Repeated Sensing Position Characteristics EE-SX910 Dark-ON d=0.002 d Light-ON 3.14 3.16 3.18 3.2 Distance d (mm) Vcc = 24 V, No. of repetitions: 20, Ta = 25C (Differential distance = 0.025 mm max.) Note: The data applies to dark status. Operation may be affected by external light interference or light coming through the sensing object. 4 EE-SX91 I/O Circuit Diagrams Output type Model EE-SX910-R EE-SX910-C1J-R EE-SX911-R EE-SX911-C1J-R NPN EE-SX912-R output EE-SX912-C1J-R EE-SX913-R EE-SX913-C1J-R EE-SX914-R EE-SX914-C1J-R EE-SX910P-R EE-SX910P-C1J-R EE-SX911P-R EE-SX911P-C1J-R PNP EE-SX912P-R output EE-SX912P-C1J-R EE-SX913P-R EE-SX913P-C1J-R EE-SX914P-R EE-SX914P-C1J-R Output transistor operation status Timing charts Output circuit Connector pin arrangement for models with connectors Light incident Light interrupted Light indicator Light indicator ON (red) OFF 1 Brown 1 OUT1 Load 1 (Black) 4 Load 2 Main circuit 2 2 3 OUT2 (White) 4 5 to 24 VDC Output 1 transistor ON OFF 3 (Blue) OUT1: Light-ON OUT2: Dark-ON Load 1 Operates (e.g., relay) Releases Light indicator Output 2 transistor ON OFF 1 4 Main circuit 2 Load 2 Operates (e.g., relay) Releases Connector pin arrangement for models with connectors (Brown) 1 OUT1 (Black) OUT2 (White) 2 5 to 24 VDC Load 1 3 4 Load 2 3 (Blue) 5 EE-SX91 Safety Precautions Refer to Warranty and Limitations of Liability. Precautions for Correct Use WARNING Installation This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. * It is assumed that EE-SX91 Sensors will be built into a device. These Sensors use non-modulated light and are not equipped to deal with interference from an external light source. When they are used in locations subject to external light interference, such as near a window or under an incandescent light, install them to minimize the effects of external light interference. * Mount the Sensors securely on a flat surface. * Use M3 or M2.0 screws to secure the Photomicrosensor. (The stronger M3 screws are recommended. In addition, use flat washers and spring washers to prevent the screws from loosening.) Refer to the following table for the correct tightening torque. Precautions for Safe Use * Power Supply Voltage Do not exceed the voltage range indicated in the specifications. Applying a voltage exceeding the specifications or using an AC power supply may result in rupture or burning. * Faulty Wiring Do not reverse the power supply polarity. Doing so may result in rupture or burning. * Do not short-circuit the load. (Do not connect to the power supply.) Doing so may result in rupture or burning. * Dispose of this product as industrial waste. Brown Load Black Load Sensor White Blue Brown Screw diameter M2.0 M3 Load Black Load Sensor Blue - + White Tightening torque 0.15 N*m max. 0.54 N*m max. * If the Sensor is to be used on a moving part, secure the cable connection point so that it is not directly subjected to stress. Wiring Unused Output Lines Be sure to isolate output lines that are not going to be used. Brown Load Black ck Sensor White Blue ((Load short-circuit) Load + - Connecting to Devices with Voltage Input Specifications A Sensor with an open-collector output can be connected to a counter with a voltage input by connecting a resistor between the power source and output. Select a resistor with reference to the following example. The resistance of the resistor is generally 4.7 k and its wattage is 1/2 W for a supply voltage of 24 V and 1/4 W for 12 V. EE-SX91 series Insert a resistor Counter (Voltage input type) +Vcc R SW main circuit Tr 24 V Power supply Input terminal (CP) Output Z 0V (Input impedance: approx. 5.6 k) 0V Example: EE-SX91 Series Load Resistance of 4.7 k Connected in a Counter Counter Specifications Input impedance 5.6 K Voltage judged as high level (input ON) 4.5 to 30 VDC Voltage judged as low level (input OFF) 0 to 2 VDC The high and low levels are found using the following formulas. The input device specifications must satisfy both formulas. High level: Z 5.6 k x 24 V = 13 V Input voltage VH = Vcc = 4.7 k+5.6 k R+Z Low level: Vcc 24 V = = 5.1 mA 100 mA Load current Ic = R R Input voltage VL 1.0 V (Residual voltage for 100-mA load current) Note: Refer to the ratings of the Sensor for the residual voltage of the load current. 6 EE-SX91 Other Precautions * Do not disconnect the Connector from the Sensor when power is supplied to the Sensor, or Sensor damage could result. * Do not install the Sensor in the following places to prevent malfunction or trouble: 1. Places exposed to dust or oil mist 2. Places exposed to corrosive gas 3. Places directly or indirectly exposed to water, oil, or chemicals 4. Outdoor or places exposed to intensive light, such as direct sunlight * Be sure to use the Sensor under the rated ambient temperature. * The Sensor may be dissolved by exposure to organic solvents, acids, alkali, or aromatic hydrocarbons, aliphatic chloride hydrocarbons causing deterioration in characteristics. Do not expose the Sensor to such chemicals. * Make sure the total length of the power cable connected to the product is less than 10 m. 7 EE-SX91 Dimensions (Unit: mm) Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified. Photomicrosensors EE-SX910-R 6 EE-SX910P-R EE-SX910-C1J-R EE-SX910P-C1J-R EE-SX911-R EE-SX911P-R EE-SX911-C1J-R EE-SX911P-C1J-R 3 24 Optical axis 13.4 5 3.7 Optical axis (2) 3 5.8 Indicator window 0.8 1.2 Optical axis 1.75 6 12 12 8 Sensing window 5 2.3 1.6 3.2 13.4 Optical axis 5 3.7 1 +V 2 OUTPUT 2 3 4 6.9 6.5 Sensing window 17.4 Indicator window Optical axis 4 6.7 8.3 6.5 8.3 8 12 Optical axis 4 6.7 1.5 13.4 5 (2) Sensing window 6.2 8 12 6.5 3.2 2 dia. 2.3 Indicator window 3.7 4.6 dia. 1.6 3.2 2.3 1.95 1.6 Connector Terminal Arrangement 300 17.4 1 2 3 4 1 2 3 4 Terminal Specifications Terminal Specifications +V 1 +V 2 OUTPUT 2 2 OUTPUT 2 4 EE-SX912-C1J-R EE-SX913-R 1 3 3 0V 4 OUTPUT 1 Robot cable of 2.8 dia., 4 cores, (0.15 mm2 with 0.8-mm dia. insulator); Standard length: 1 m 17.4 0V EE-SX913-C1J-R OUTPUT 1 Accessories (Order Separately) EE-SX914-R EE-SX914P-R EE-SX914-C1J-R EE-SX914P-C1J-R 3 6 Connector with Robot Cable EE-1016-R Optical axis Optical axis 13.4 5 0.8 3.7 (2) 6.5 1.2 8.3 8 5.8 8.3 Indicator window 8 10 Terminal Arrangement A Two, 3.2 dia. 300 1 2 3 4 10 2,000 16 7 4 3 2 1 2 Indicator window Connector Terminal Arrangement Sensing window 11.5 16 4 1.2 0.8 (0.15 mm2 with 0.8-mm dia. insulator); Standard length: 1 m EE-SX912-R 3 2 dia. 4.6 dia. 3.7 Connector Terminal Arrangement Robot cable of 2.8 dia., 4 cores, +V 3 5 Indicator window OUTPUT 2 11.7 (R1.6) 5 2 OUTPUT 1 6 Optical axis (R1.6) 0.8 1 0V 4 Optical axis 13.4 5 (2) 6.2 Terminal Specifications OUTPUT 2 3 EE-SX911-R EE-SX913-R EE-SX913P-R EE-SX913-C1J-R EE-SX913P-C1J-R 6 1.5 300 +V 2 EE-SX910-C1J-R 11.7 1.95 1 0V OUTPUT 1 Sensing window 1.2 10 2 cores, (0.15 mm2 with 0.8mm dia. insulator); Standard length: 1 m Terminal Specifications 4 12 Robot cable of 2.8 dia., 4 EE-SX912-R EE-SX912P-R EE-SX912-C1J-R EE-SX912P-C1J-R 3 0.8 (2) Connector Terminal Arrangement Terminal Specifications 1 2 3 4 6 1.2 300 EE-SX910-R Connector Terminal Arrangement Robot cable of 2.8 dia., 4 cores, (0.15 mm2 with 0.8-mm dia. insulator); Standard length: 1 m 8 (Four, R1.6) 4.6 dia. Two, 3.2 dia. 18.7 1 2 3 4 300 17.4 EE-SX911-C1J-R 6.5 8.3 2.7 + Robot cable of 2.8 dia., 4 cores, (0.15 mm2 with 0.8-mm dia.insulator); Standard length: 2 m Brown B OUTPUT 2 White Blue C - D OUTPUT 1 Black EE-SX914-R Robot cable of 2.8 dia., 4 cores, (0.15 mm2 with 0.8-mm dia. insulator); Standard length: 1 m 17.4 0V OUTPUT 1 EE-SX914-C1J-R 8 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: * Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. * Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. * Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased products. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. ERRORS AND OMISSIONS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. 2008.11 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2008 All Right Reserved.