CLD-DS90 Rev 1J Product family data sheet Cree(R) XLamp(R) XB-H LEDs Product Description The XLamp(R) breakthrough XB-H LED combination delivers of a FEATURES Table of Contents * Available in white, outdoor white Characteristics.........................................2 and 80-, 85- and 90-CRI white Flux Characteristics.................................3 lumen output and efficacy in a small package. * ANSI-compatible chromaticity bins Relative Spectral Power Distribution......4 Delivering more than 500 lumens at * Binned at 85 C Relative Flux vs. Junction 1.5 A, 25 C in a 2.45 mm package, the * Maximum drive current: 1500 mA Temperature ............................................4 Cree XB-H LED offers triple the lumen * Low thermal resistance: 4 C/W Electrical Characteristics.........................5 density of competing highpower LEDs * Wide viewing angle: 110 Relative Flux vs. Current..........................5 to significantly increase the performance * Unlimited floor life at Relative Chromaticity vs Current and 30 C/85% RH Temperature.............................................6 Reflow solderable - JEDEC Typical Spatial Distribution......................7 2 of today's lighting designs. The XB-H LED joins a new generation of directionally * optimized LEDs that offers the industry's JSTD020C Thermal Design........................................7 highest optical control factor (OCF), * Electrically neutral thermal path Reflow Soldering Characteristics............8 a measurement of how LED size and * RoHS and REACh compliant Notes........................................................9 performance benefit directional lighting * UL recognized component Mechanical Dimensions........................11 (E349212) Tape and Reel.........................................12 applications. HighOCF LEDs enable lighting manufacturers to improve the (R) Packaging...............................................13 performance of any lighting design, create smaller and less expensive systems, and develop new lighting solutions that were www.cree.com/Xlamp previously not possible. Copyright (c) 2014-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R) and XLamp(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 XLamp (R) XB-H LED Characteristics Characteristics Unit Thermal resistance, junction to solder point C/W 4 degrees 110 mV/C -2.2 Viewing angle (FWHM) Temperature coefficient of voltage ESD withstand voltage (HBM per Mil-Std-883D) Minimum Typical Maximum V 8000 mA 1500 Reverse voltage V 5 Forward voltage (@ 700 mA, 85 C) V 2.9 Forward voltage (@ 1000 mA, 85 C) V 3.0 Forward voltage (@ 1500 mA, 85 C) V 3.15 LED junction temperature C DC forward current 3.3 150 Copyright (c) 2014-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R) and XLamp(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 2 XLamp (R) XB-H LED Flux Characteristics (TJ = 85 C) The following table provides several base order codes for XLamp XB-H LEDs. It is important to note that the base order codes listed here are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the ordercode nomenclature, please consult the XLamp XB LED Family Binning and Labeling document. CCT Range Minimum Luminous Flux @ 700 mA Color Min. Cool White Outdoor White Neutral White 80-CRI Minimum White Warm White 85-CRI Minimum White 90-CRI Minimum White 5000 K 3200 K 3700 K 2600 K 2600 K 2600 K 2600 K Max. 8300 K 5300 K 5300 K 4300 K 3700 K 3200 K 3200 K Calculated Minimum Luminous Flux (lm)** @ 85 C Order Code Group Flux (lm) @ 85 C Flux (lm) @ 25 C* 1.0 A 1.5 A T6 280 322 372 499 XBHAWT-00-0000-000LT60E1 T5 260 299 345 463 XBHAWT-00-0000-000LT50E1 T4 240 276 318 428 XBHAWT-00-0000-000LT40E1 T3 220 253 292 392 XBHAWT-00-0000-000LT30E1 T6 280 322 372 499 XBHAWT-00-0000-0000T60E3 T5 260 299 345 463 XBHAWT-00-0000-0000T50E3 T4 240 276 318 428 XBHAWT-00-0000-0000T40E3 T3 220 253 292 392 XBHAWT-00-0000-0000T30E3 T5 260 299 345 463 XBHAWT-00-0000-000LT50E4 T4 240 276 318 428 XBHAWT-00-0000-000LT40E4 T3 220 253 292 392 XBHAWT-00-0000-000LT30E4 T4 240 276 318 428 XBHAWT-00-0000-000HT40E5 T3 220 253 292 392 XBHAWT-00-0000-000HT30E5 T4 240 276 318 428 XBHAWT-00-0000-0000T40E7 T3 220 253 292 392 XBHAWT-00-0000-0000T30E7 T2 200 230 265 356 XBHAWT-00-0000-0000T20E7 T2 200 230 265 356 XBHAWT-00-0000-000PT20E7 S6 182 209 242 324 XBHAWT-00-0000-000PS60E7 S5 172 198 228 306 XBHAWT-00-0000-000PS50E7 S6 182 209 242 324 XBHAWT-00-0000-000US60E7 S5 172 198 228 306 XBHAWT-00-0000-000US50E7 S4 164 186 218 292 XBHAWT-00-0000-000US40E7 Notes: * Cree maintains a tolerance of 7% on flux and power measurements, 0.005 on chromaticity (CCx, CCy) measurements and 2 on CRI measurements. See the Measurements section (page 9). * Typical CRI for Cool White (5000 K - 8300 K CCT) is 70. * Typical CRI for Neutral White (3700 K - 5300 K CCT) is 75. * Typical CRI for Warm White (2600 K - 3700 K CCT) is 80. * Flux values @ 25 C are calculated and for reference only. ** Calculated flux values at 1 A and 1.5 A are for reference only. Copyright (c) 2014-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R) and XLamp(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 3 XLamp (R) XB-H LED Relative Spectral Power Relative Spectral Power Distribution 100% Relative Radiant Power 80% 60% Cool White Warm White 40% 20% 0% 380 430 480 530 580 630 680 730 780 Wavelength (nm) Relative Flux Output vs. Junction Temperature Relative Flux vs. Junction Temperature (IF = 700 mA) 120% Relative Luminous Flux 100% 80% 60% 40% 20% 0% 25 50 75 100 125 150 Junction Temperature (C) Copyright (c) 2014-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R) and XLamp(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 4 XLamp (R) XB-H LED Electrical Characteristics (Tj = 25C) Electrical Characteristics (TJ = 85 C) 1500 Forward Current (mA) 1200 900 600 300 0 2.50 2.75 3.00 3.25 Forward Voltage (V) Relative Intensity vs. Current (Tj = 25C) Relative Flux vs. Current (TJ = 85 C) 180% 160% Relative Luminous Flux 140% 120% 100% 80% 60% 40% 20% 0% 0 300 600 900 1200 1500 Forward Current (mA) Copyright (c) 2014-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R) and XLamp(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 5 XLamp (R) XB-H LED Delta CCT vs. Current Relative Chromaticity vs Current and Temperature (Warm White*) 0.006 0.004 0.002 CCx 0.000 CCy -0.002 -0.004 Delta CCT vs Temp -0.006 100 300 500 700 900 1100 1300 1500 Current (mA) 0.006 0.004 0.002 CCx 0.000 CCy -0.002 -0.004 -0.006 25 50 75 100 125 150 Tsp (C) * Warm White XLamp XB-H LEDs have a typical CRI of 80. Copyright (c) 2014-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R) and XLamp(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 6 XLamp (R) XB-H LED Typical Spatial Radiation Pattern Typical Spatial Distribution 100% Relative Luminous Intensity 80% 60% 40% 20% -90 -60 0% -30 0 30 60 90 Angle () Thermal Design The maximum forward current is determined by the thermal resistance between the LED junction and ambient. It is crucial for the end Thermal Design product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life and optical characteristics. 1600 Maximum Current (mA) 1400 1200 1000 800 600 Rj-a = 10 C/W 400 Rj-a = 15 C/W Rj-a = 20 C/W 200 0 Rj-a = 25 C/W 0 20 40 60 80 100 120 140 160 Ambient Temperature (C) Copyright (c) 2014-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R) and XLamp(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 7 XLamp (R) XB-H LED Reflow Soldering Characteristics In testing, Cree has found XLamp XB-H LEDs to be compatible with JEDEC J-STD-020C, using the parameters listed below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the solder paste used, and therefore it is the lamp or luminaire manufacturer's responsibility to determine applicable soldering requirements. Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment. tP TP Critical Zone TL to TP Temperature Ramp-up TL tS Tsmax Tsmin Ramp-down ts Preheat 25 t 25C to Peak IPC/JEDEC J-STD-020C Time Profile Feature Average Ramp-Up Rate (Tsmax to Tp) Lead-Free Solder 1.2 C/second Preheat: Temperature Min (Tsmin) 120 C Preheat: Temperature Max (Tsmax) 170 C Preheat: Time (tsmin to tsmax) Time Maintained Above: Temperature (TL) Time Maintained Above: Time (tL) Peak/Classification Temperature (Tp) 65-150 seconds 217 C 45-90 seconds 235 - 245 C Time Within 5 C of Actual Peak Temperature (tp) 20-40 seconds Ramp-Down Rate 1 - 6 C/second Time 25 C to Peak Temperature 4 minutes max. Note: All temperatures refer to topside of the package, measured on the package body surface. Copyright (c) 2014-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R) and XLamp(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 8 XLamp (R) XB-H LED Notes Measurements The luminous flux, radiant power, chromaticity, forward voltage and CRI measurements in this document are binning specifications only and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number of factors that are not within Cree's control and are not intended or provided as operational specifications for the products. Calculated values are provided for informational purposes only and are not intended or provided as specifications. PreRelease Qualification Testing Please read the LED Reliability Overview for details of the qualification process Cree applies to ensure long-term reliability for XLamp LEDs and details of Cree's pre-release qualification testing for XLamp LEDs. Lumen Maintenance Cree now uses standardized IES LM-80-08 and TM-21-11 methods for collecting long-term data and extrapolating LED lumen maintenance. For information on the specific LM-80 data sets available for this LED, refer to the public LM-80 results document. Please read the Long-Term Lumen Maintenance application note for more details on Cree's lumen maintenance testing and forecasting. Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect the LED junction temperature. Moisture Sensitivity Cree recommends keeping XLamp LEDs in the provided, resealable moisture-barrier packaging (MBP) until immediately prior to soldering. Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity. Once the MBP is opened, XLamp XB-H LEDs may be stored as MSL 1 per JEDEC J-STD-033, meaning they have unlimited floor life in conditions of 30 C/85% relative humidity (RH). Regardless of storage condition, Cree recommends sealing any unsoldered LEDs in the original MBP. RoHS Compliance The levels of RoHS restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Directive 2011/65/EC (RoHS2), as implemented January 2, 2013. RoHS Declarations for this product can be obtained from your Cree representative or from the Product Ecology section of the Cree website. REACh Compliance REACh substances of very high concern (SVHCs) information is available for this product. Since the European Chemical Agency (ECHA) has published notice of their intent to frequently revise the SVHC listing for the foreseeable future, please contact a Cree representative to insure you get the most up-to-date REACh SVHC Declaration. REACh banned substance information (REACh Article 67) is also available upon request. Copyright (c) 2014-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R) and XLamp(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 9 XLamp (R) XB-H LED Notes - Continued UL(R) Recognized Component This product meets the requirements to be considered a UL Recognized Component with Level 4 enclosure consideration. The LED package or a portion thereof has been investigated as a fire and electrical enclosure per ANSI/UL 8750. Vision Advisory WARNING: Do not look at an exposed lamp in operation. Eye injury can result. For more information about LEDs and eye safety, please refer to the LED Eye Safety application note. Copyright (c) 2014-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R) and XLamp(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 10 XLamp (R) XB-H LED 6 5 6 5 NOTICE NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE THE PROPRIETARY AND CONTAINED WITHIN ARE THE PROPRIETARY AND CONFIDENTIAL CREE, INC. THIS PLOT CONFIDENTIAL INFORMATIONINFORMATION OF CREE, INC.OF THIS PLOT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY UNAUTHORIZED PERSON THE WITHOUT WRITTEN CONSENT UNAUTHORIZED PERSON THE WITHOUT WRITTEN CONSENT Mechanical Dimensions CREE INC. OF CREE INC. OF 4 4 3 3 REV Thermal vias, if present, are not shown on these drawings. All measurements are .13 mm unless 2.29 otherwise indicated. 2.29 D D 2.28 2.28 2.45 2.45 6 5 6 5 NOTICE CREE CONFIDENTIAL. NOTICE THIS PLOT AND THE INFORMATION CONTAINED WITHIN ARE PROPRIETARY AND CREE CONFIDENTIAL. THISTHE PLOT AND THE INFORMATION CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT CONTAINED WITHIN ARE THE PROPRIETARY AND MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE,CONSENT INC. THIS PLOT UNAUTHORIZED PERSON THE WITHOUT WRITTEN MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY OF CREE INC. PERSON UNAUTHORIZED THE WITHOUT WRITTEN CONSENT 2.45 2.45INC. OF CREE 4 3 4 3 2.29 2.28 C C Anode D 2.29 2.29 0.92 0.36 2.29 R1.53 0.92 R1.53 0.36 2.29 2.29 2.29 0.85REF. 2.29 0.85 2.29 REF. 0.39 0.92 0.92 Anode 2.29 PRIMARY D PRIMARY 0.39 0.36 0.36 0.85 6 0.85 2.29 0.25 Recommended PCB Solder Pad0.25 0.17 2.29 2.29 5 5 1.95 1.95 1.95 Alternate Bottom View 2.29 ALTENATIVE 2.29 0.85 0.85 C 0.25 0.25 0.17 0.39 0.39 0.17 ALL DIMENS UNL UNLESS OTHERWISE DIMENSIONS ARED 2.29 RECOMMENDED RECOMMENDED PCB SOLDER PADPCB SOLDER PAD 0.85 0.39 0.39 2.29 2.29 6 2.29 2.29 ALTENATIVE PRIMARY 0.92 0.92 0.85 0.92 2.29 2.29 0.92 2.29 PRIMARY 2.29 2.29 A DATE APP'D PRIMARY C PRIMARY 0.85 0.85 Bottom View 2.29 1 0.36 0.92 9 2.29 REF. B B B B A REVISONS BY DATE APP'D2.29BY DESCRIPTION 2.29 0.33 0.33 0.65 0.36 0.65 0.36 0.92 Side View 0.33 0.36 0.65 2.45 2.45 2.29 1 2 REVISONS DESCRIPTION REV 2.29 REF. 2.29 0.33 2.28 0.65 2 R1.53 R1.53 Top View 3 3 REV REV 2.28 2.28 2.45 2.45 C C 0.36 0.36 4 4 REV MATION D PLOT D D TO ANY 0.33 0.33 0.65 0.65 0.85 MILL RECOMMENDED STENCIL PATTERN MILLIMETERS AND AF RECOMMENDED STENCIL PATTERN TOLE TOLERANCE UNLESS AREA0.85 IS OPENING) (HATCHED AREA (HATCHED IS OPENING) .XX .25 .XXX .125 1.95 X .5 THIRD ANGLE PROJECTIO THIRD ANGLE PROJECTION 1.95 FOR FOR SHEET PA B B.X METAL 1.5 0.25 .XX .75 .XXX .25 0.17 0.25 X .5 0.17 1.6 SUR SURFACE FINISH: 4 3 4 3 1.95 ALL DIMENSI ALL DIMENSIO Recommended Stencil Pattern (Hatched Area is Opening) RECOMMENDED STENCIL PATTERN UNLESS OTHERWISE SD D DIMENSIONS ARESP IN UNLESS OTHERWISE MILLIMETERS DIMENSIONSAND AREAFT INDC TOLERANCEAND UNLESS S C MILLIMETERS AFTER RECOMMENDED STENCIL PATTERN (HATCHED AREA IS OPENING) .XX UNLESS .25 SPA TOLERANCE (HATCHED AREA IS (R)OPENING) .XXX .25 .125 A Copyright (c) 2014-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R) and XLamp are registered trademarks and the Cree logo is a trademark of .XX X .125 .5 ALL DIMENSIONS AREALL DIMENSIONS .13MM UNLESS NOTED THIRD .XXX Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. ANGLE PROJECTION AREOTHERWISE .13MM UNLESS OTHERWISE NOTED FOR SHEET PAM X METAL .5 THIRD ANGLE PROJECTION M .X 1.5 PART FOR SHEET METAL 1.5 .75 .X.XX 11 DATE DRAWN BY .XXX .25 F .XX DATE DRAWN BY UNLESS OTHERWISE UNLESS SPECIFIED 4600 Silicon Drive X .75 .5 OTHERWISE CRONIN 11/20/13SPECIFIED .25 FI DIMENSIONS ARE IND. Silicon.XXX Drive DIMENSIONS ARE IND. CRONIN11/20/13 Durham, N.C 27703 4600 1.6 CHECK DATE FINISH: .5 Durham,SURFACE N.CX27703 A A 0.17 RECOMMENDED PCB SOLDER PAD RECOMMENDED PCB SOLDER PAD REVISONS REVISONS REV BY DATEAPP'D DESCRIPTION REV BY DATEAPP'D DESCRIPTION DC 10/23/11 A Released JL DC AB Released AND ANODE NOTE JL 2/26/12 DC 10/23/11 ADDED CATHODE 2/26/12 DC BC ADDED CATHODE AND ANODE NOTE DC 8/3/12 CHANGED POCKET DIMS AND TOLERANCES 8/3/12 DC CHANGEDPOCKET POCKETDIMS DIM TO INSIDE OF POCKET CD CHANGED AND TOLERANCES 2/1/18 IN BOTTOM VIEW DC CHANGED POCKET DIM TO INSIDE DC OF POCKET 2/1/18 IN BOTTOM VIEW D NOTICE CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION NOTICE CONTAINED WITHIN ARE THE PROPRIETARY AND CREE CONFIDENTIAL. THIS PLOT THE INFORMATION CONFIDENTIAL INFORMATION OFAND CREE, INC. THIS PLOT CONTAINED ARE THE PROPRIETARY AND MAY NOT BEWITHIN COPIED, REPRODUCED OR DISCLOSED TO ANY CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT UNAUTHORIZED PERSON THE WRITTEN WITHOUT CONSENT MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY OF CREE INC. UNAUTHORIZED PERSON THE WRITTEN WITHOUT CONSENT OF CREE INC. DETAIL B SCALE 2 : 1 D D XLamp (R) XB-H LEDDD Tape and Reel All Cree carrier tapes conform to EIA-481D, Automated Component Handling Systems Standard. C C 4.00 .10 4.00 .10 2.00 .10 2.00 .10 B B CATHODE SIDE CATHODE SIDE 1.5.1 1.75.10 ANODE SIDE ANODE SIDE 8.00 .10 8.00 .10 1.75 .10 1.75 .10 B B 4.0.1 B B C C Except as noted, all dimensions in mm. 1.50 +.10/-.00 1.50 +.10/-.00 8.0.1 4 4 12.00 Nominal 12.00 Nominal 12.30 Max 12.30 Max 10.25 .10 10.25 .10 2.60+/-0.1mm 2.60+/-0.1mm 2.5.1 Cathode Side 1.00 .10 1.00 .10 .30 .10 .30 .10 5.50 .10 5.50 .10 B B +.3 12.0 .0 2.05+/-0.1 2.05+/-0.1 SECTION B-B Anode SECTION B-BSide 2.60 +/-0.1 2.60 +/-0.1 A A END Notes: Notes: 1. 10 sprocket hole pitch cumulative tolerance 1. 10 sprocket hole pitch cumulative tolerance 6 6 (denoted by + and circle) 0.2mm 0.2mm 5 5 4 4 Trailer 160mm (min) of empty pockets sealed with tape (20 pockets min.) REFERENCE VENDOR PART NUMBER 020246 REFERENCE VENDOR PART NUMBER 020246 DRAWN BY DATE UNLESS OTHERWISE SPECIFIED 4600 Silicon Drive D.IN CRONIN 10/23/11 DRAWN BY DATE DIMENSIONS ARE Durham, N.CDrive 27703 UNLESS OTHERWISE SPECIFIED CHECK DATE 4600 Silicon MILLIMETERS AND AFTER FINISH. D.IN CRONIN 10/23/11 Phone (919) 313-5300 DIMENSIONS ARE Durham, N.C 27703 TOLERANCE UNLESS SPECIFIED: CHECK DATE Fax (919) 313-5558 User Feed Direction MILLIMETERS AND AFTER FINISH. Phone (919) 313-5300 .XX .25 APPROVED DATE A TOLERANCE UNLESS SPECIFIED: Fax (919) 313-5558 .XXX .25 .125 APPROVED .XX DATE TITLE A X .125 .5 .XXX START THIRD ANGLE PROJECTION Tape, 2525 HEW MATERIAL FOR SHEET PARTS ONLY TITLECarrier X .5METAL THIRD ANGLE PROJECTION Carrier Tape, 2525 HEW REV. .X METAL 1.5 MATERIAL FOR SHEET PARTS ONLY SIZE DRAWING NO. .XX .75 .X 1.5 .XXX .25 FINAL PROTECTIVE 2402-00020 REV. DRAWING NO. SIZE CFINISH .XX D X .75 .5 .XXX .25 FINAL PROTECTIVE 2402-00020 SCALE SHEET OFD1/1 CFINISH 1.6 SURFACE 4.000 X FINISH: .5 SCALE SHEET OF 1.6 SURFACE FINISH: 4.000 1/1 3 2 1 3 Loaded Pockets (1,000 Lamps) 2 1 Leader 400mm (min) of empty pockets with at least 100mm sealed by tape (50 empty pockets min.) User Feed Direction Cover Tape Pocket Tape 13mm 7" Copyright (c) 2014-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R) and XLamp(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 12 XLamp (R) XB-H LED Packaging Unpackaged Reel Vacuum-Sealed Vacuum-Sealed Moisture Barrier Bag Moisture Barrier Bag Label CREE Binwith Code Cree Bin & Barcode LabelLot # Code, Qty, Label with Cree Bin Code, Quantity, Reel ID Label with Cree Bin Label with Customer P/N, Qty,Qty, Lot #, Lot PO # # Code, Packaged Reel Patent Label Label with Customer Order Label with Cree Order Code, Code, Qty, Reel ID, PO # Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Boxed Reel Label with Cree Order Code, Quantity, Reel ID, PO # Label with Cree Bin Code, Quantity, Reel ID Patent Label (on bottom of box) Copyright (c) 2014-2018 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree(R) and XLamp(R) are registered trademarks and the Cree logo is a trademark of Cree, Inc. UL(R) and the UR logo are registered trademarks of UL LLC. 13 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Cree, Inc.: XBHAWT-00-0000-000PS60F8 XBHAWT-00-0000-0000T50C3 XBHAWT-00-0000-000HT20Z7 XBHAWT-00-0000000PS50Z8 XBHAWT-00-0000-000US40Z7 XBHAWT-00-0000-000LT30E4 XBHAWT-00-0000-0000T30E4 XBHAWT-00-0000-0000T30C3 XBHAWT-00-0000-000US50E8 XBHAWT-00-0000-000LT30Z5 XBHAWT-00-00000000T40C3 XBHAWT-00-0000-000HT30E6 XBHAWT-00-0000-000LT20F8 XBHAWT-00-0000-0000T20E6 XBHAWT00-0000-0000T40F7 XBHAWT-00-0000-000US40E7 XBHAWT-00-0000-000LT30E1 XBHAWT-00-0000-0000T30D1 XBHAWT-00-0000-000LS60Z8 XBHAWT-00-0000-000US60E7 XBHAWT-00-0000-0000T30F7 XBHAWT-00-0000000HT30F8 XBHAWT-00-0000-000LT20E8 XBHAWT-00-0000-000US60F8 XBHAWT-00-0000-000LT5053 XBHAWT00-0000-000US60Z7 XBHAWT-00-0000-000LT40E4 XBHAWT-00-0000-000US40F8 XBHAWT-00-0000-0000T50C2 XBHAWT-00-0000-000HT20F7 XBHAWT-00-0000-0000T50F5 XBHAWT-00-0000-000LT3053 XBHAWT-00-0000000LT20Z8 XBHAWT-00-0000-000LT40E1 XBHAWT-00-0000-0000T30D3 XBHAWT-00-0000-000LT30F6 XBHAWT00-0000-000HT30Z6 XBHAWT-00-0000-0000T20F6 XBHAWT-00-0000-0000T30D4 XBHAWT-00-0000-000HT30E7 XBHAWT-00-0000-0000T30F6 XBHAWT-00-0000-000LT30F5 XBHAWT-00-0000-0000T50E4 XBHAWT-00-0000000LT30E7 XBHAWT-00-0000-0000T40C6 XBHAWT-00-0000-000LT50E2 XBHAWT-00-0000-0000T40E7 XBHAWT00-0000-000PS50E7 XBHAWT-00-0000-000PT20E7 XBHAWT-00-0000-000HT30F7 XBHAWT-00-0000-000LS60F8 XBHAWT-00-0000-000LT4050 XBHAWT-00-0000-000PS40E8 XBHAWT-00-0000-000LT30F4 XBHAWT-00-00000000T40F6 XBHAWT-00-0000-000LT20E6 XBHAWT-00-0000-000HT20F8 XBHAWT-00-0000-0000T50E3 XBHAWT00-0000-0000T30F5 XBHAWT-00-0000-000LT5051 XBHAWT-00-0000-000PS40Z8 XBHAWT-00-0000-000LT40Z5 XBHAWT-00-0000-000LS60E8 XBHAWT-00-0000-000PS50F8 XBHAWT-00-0000-0000T40F5 XBHAWT-00-00000000T40C5 XBHAWT-00-0000-000HT40E6 XBHAWT-00-0000-000US40E8 XBHAWT-00-0000-000US50Z7 XBHAWT-00-0000-0000T30E6 XBHAWT-00-0000-0000T40E6 XBHAWT-00-0000-0000T50D3 XBHAWT-00-00000000T30E3 XBHAWT-00-0000-000LT50F4 XBHAWT-00-0000-000US50F8 XBHAWT-00-0000-0000T40F4 XBHAWT00-0000-000HT20E7 XBHAWT-00-0000-000HT40Z5 XBHAWT-00-0000-000LT30E6 XBHAWT-00-0000-000LT30E5 XBHAWT-00-0000-000HT30E8 XBHAWT-00-0000-000LT30E8 XBHAWT-00-0000-000US40Z8 XBHAWT-00-00000000T50D2 XBHAWT-00-0000-0000T30C1 XBHAWT-00-0000-000LT20Z6 XBHAWT-00-0000-0000T50C4 XBHAWT00-0000-000LT20F6 XBHAWT-00-0000-0000T50C1 XBHAWT-00-0000-0000T40D2 XBHAWT-00-0000-000LT50E1 XBHAWT-00-0000-0000T50F4 XBHAWT-00-0000-0000T40C1 XBHAWT-00-0000-000LT50E4 XBHAWT-00-00000000T40E5 XBHAWT-00-0000-000HS60F8 XBHAWT-00-0000-000LT40E6 XBHAWT-00-0000-000HT30F6 XBHAWT-00-0000-000LT3051 XBHAWT-00-0000-0000T30D2