THIS PAGE INTENTIONALLY LEFT BLANK
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HIGH SPEED DIGITAL LOGIC - SMT
1
HMC722LC3C
v04.0313
GATE, w/ PROGRAMMABLE OUTPUT VOLTAGE
13 Gbps, FAST RISE TIME AND/NAND/OR/NOR
The HMC722LC3C is an AND/NAND/OR/NOR fun-
ction designed to support data transmission rates
of up to 13 Gbps, and clock frequencies as high
as 13 GHz. The HMC772LC3C may be easily con-
gured to provide any of the following logic functions:
AND, NAND, OR and NOR. The HMC722LC3C also
features an output level control pin, VR, which allows
for loss compensation or for signal level optimization.
All input signals to the HMC722LC3C are terminated
with 50 Ohms to ground on-chip, and may be either
AC or DC coupled. The differential outputs of the
HMC722LC3C may be either AC or DC coupled.
Outputs can be connected directly to a 50 Ohm to ground
terminated system, while DC blocking capacitors may
be used if the terminating system is 50 Ohms to a non-
ground DC voltage. The HMC722LC3C operates from
a single -3.3V DC supply, and is available in a ceramic
RoHS compliant 3x3 mm SMT package.
General Description
Features
Functional Diagram
Supports High Data Rates: up to 13 Gbps
Differential & Singe-Ended Operation
Fast Rise and Fall Times: 19 / 18 ps
Low Power Consumption: 230 mW typ.
Programmable Differential
Output Voltage Swing: 600 - 1100 mV
Propagation Delay: 95 ps
Single Supply: -3.3V
16 Lead Ceramic 3x3mm SMT Package: 9mm2
Typical Applications
The HMC722LC3C is ideal for:
• RF ATE Applications
• Broadband Test & Measurement
• Serial Data Transmission up to 13 Gbps
• Digital Logic Systems up to 13 GHz
• NRZ-to-RZ Conversion
Electrical Specications, TA = +25 °C, Vee = -3.3V
Parameter Conditions Min. Typ. Max Units
Power Supply Voltage -3.6 -3.3 -3.0 V
Power Supply Current 70 mA
Maximum Data Rate 13 Gbps
Maximum Clock Rate 13 GHz
Input High Voltage -0.5 0.5 V
Input Low Voltage -1.0 0.0 V
Input Return Loss Frequency <13 GHz 10 dB
Output Amplitude Single-Ended, peak-to-peak 550 mVp-p
Differential, peak-to-peak 110 0 mVp-p
Output High Voltage -10 mV
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HIGH SPEED DIGITAL LOGIC - SMT
2
HMC722LC3C
v04.0313
GATE, w/ PROGRAMMABLE OUTPUT VOLTAGE
13 Gbps, FAST RISE TIME AND/NAND/OR/NOR
Electrical Specications, (continued)
Parameter Conditions Min. Typ. Max Units
Output Low Voltage -570 mV
Output Rise / Fall Time Differential, 20% - 80% 19 / 18 ps
Output Return Loss Frequency <13 GHz 10 dB
Small Signal Gain 27 dB
Random Jitter Jr rms 0.2 ps rms
Deterministic Jitter, Jd peak-to-peak, 215-1 PRBS input [1] 2 ps, p-p
Propagation Delay, td 95 ps
[1] Deterministic jitter calculated by simultaneously measuring the jitter of a 300 mV, 13 GHz, 215-1 PRBS input, and a single-ended output
[1] VR = 0.0V [2] Frequency = 13 GHz [3] Frequency = 10 GHz
DC Current vs. Supply Voltage [1] [2] Output Differential
vs. Supply Voltage [1] [3]
Output Differential vs. VR [2]
55
60
65
70
75
80
85
-3.7 -3.6 -3.5 -3.4 -3.3 -3.2 -3.1 -3 -2.9
+25C
+85C
-40C
DC CURRENT (mA)
SUPPLY VOLTAGE (V)
400
500
600
700
800
900
1000
1100
1200
-1.2 -1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4
+25C
+85C
-40C
VR (V)
DIFFERENTIAL VOLTAGE (mV)
800
850
900
950
1000
1050
1100
1150
1200
-3.7 -3.6 -3.5 -3.4 -3.3 -3.2 -3.1 -3 -2.9
+25C
+85C
-40C
DIFFERENTIAL VOLTAGE (mV)
SUPPLY VOLTAGE (V)
Output Differential vs. Frequency [3]
600
700
800
900
1000
1100
1200
1300
2 4 6 8 10 12 14 16
OUTPUT DIFFERENTIAL (mV)
INPUT FREQUENCY (GHz)
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HIGH SPEED DIGITAL LOGIC - SMT
3
HMC722LC3C
v04.0313
GATE, w/ PROGRAMMABLE OUTPUT VOLTAGE
13 Gbps, FAST RISE TIME AND/NAND/OR/NOR
[1] VR = 0.0V [2] Frequency = 13 GHz [3] Frequency = 10 GHz
Input Return Loss vs. Frequency Output Return Loss vs. Frequency
-35
-30
-25
-20
-15
-10
0 2 4 6 8 10 12 14
RETURN LOSS (dB)
FREQUENCY (GHz)
-50
-40
-30
-20
-10
0
0 2 4 6 8 10 12 14
RETURN LOSS (dB)
FREQUENCY (GHz)
Rise / Fall Time vs. VR [3]
15
17
19
21
23
25
-1.2 -1 -0.8 -0.6 -0.4 -0.2 0 0.2 0.4
tr
tf
RISE/FALL TIME (ps)
VR (V)
Rise / Fall Time vs. Supply Voltage [3]
15
17
19
21
23
25
-3.7 -3.6 -3.5 -3.4 -3.3 -3.2 -3.1 -3 -2.9
tr
tf
RISE/FALL TIME (ps)
SUPPLY VOLTAGE (V)
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HIGH SPEED DIGITAL LOGIC - SMT
4
HMC722LC3C
v04.0313
GATE, w/ PROGRAMMABLE OUTPUT VOLTAGE
13 Gbps, FAST RISE TIME AND/NAND/OR/NOR
Eye Diagram
Timing Diagram
Truth Table
Input Outputs
A B D
L L L
L H L
H L L
H H H
Notes:
A = AP - AN
B = BP - BN
D = DP - DN
H - Positive voltage level
L - Negative voltage level
[1] Test Conditions:
Pattern generated with an Agilent N4903A Serial BERT.
Eye Diagram presented on a Tektronix CSA 8000.
Device input = 10 Gbps PN code, Vin = 300mVp-p differential.
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HIGH SPEED DIGITAL LOGIC - SMT
5
HMC722LC3C
v04.0313
GATE, w/ PROGRAMMABLE OUTPUT VOLTAGE
13 Gbps, FAST RISE TIME AND/NAND/OR/NOR
Absolute Maximum Ratings
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
Power Supply Voltage (Vee) -3.7 5 V to +0. 5 V
Input Signals -2 V to +0.5 V
Output Signals -1.5 V to +1 V
Storage Temperature -65 °C to +150 °C
Operating Temperature -4 °C to +85 °C
ESD Sensitivity (HBM) Class 1C
NOTES:
1. PACKAGE BODY MATERIAL: ALUMINA
2. LEAD AND GROUND PADDLE PLATING:
30-80 MICROINCHES GOLD OVER 50 MICROINCHES MINIMUM NICKEL.
3. DIMENSIONS ARE IN INCHES [MILLIMETERS].
4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm DATUM -C-
6. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND.
7. GROUND PADDLE MUST BE SOLDERED TO Vee.
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HIGH SPEED DIGITAL LOGIC - SMT
6
HMC722LC3C
v04.0313
GATE, w/ PROGRAMMABLE OUTPUT VOLTAGE
13 Gbps, FAST RISE TIME AND/NAND/OR/NOR
Pin Descriptions
Pin Number Function Description Interface Schematic
1, 4, 5, 8, 9, 12 GND Signal Grounds
2, 3 AN, AP Clock / Data Input A
6, 7 BN, BP Clock / Data Input B
10, 11 D P, D N Clock / Data Output
13, 16 GND Supply Ground
14 VR
Output level control. Output level may be adjusted by
either applying a voltage to VR per “Output Differential vs.
VR” plot.
15, Package
Base Vee Negative Supply
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HIGH SPEED DIGITAL LOGIC - SMT
7
HMC722LC3C
v04.0313
GATE, w/ PROGRAMMABLE OUTPUT VOLTAGE
13 Gbps, FAST RISE TIME AND/NAND/OR/NOR
Evaluation PCB
List of Materials for Evaluation PCB 118777 [1]
Item Description
J1 - J6 PCB Mount SMA RF Connectors
J7 - J9 DC Pin
C1, C2 100 pF Capacitor, 0402 Pkg.
C3, C4 4.7 µF Capacitor, Tantalum
R1 10 Ohm Resistor, 0603 Pkg.
U1 HMC722LC3C
High Speed Logic, AND / NAND / OR / NOR
PCB [2] 118775 Evaluation Board
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
Item Description
J1 AN
J2 AP
J3 BN
J4 BP
J5 DP
J6 DN
J7 Vee
J8 VR
J9 GND
The circuit board used in the application should use
RF circuit design techniques. Signal lines should
have 50 Ohm impedance while the package gro-
und leads should be connected directly to the
ground plane similar to that shown. The exposed
package base should be connected to Vee. A suffi-
cient number of via holes should be used to connect
the top and bottom ground planes. The evaluation
circuit board shown is available from Hittite upon
request.
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
HIGH SPEED DIGITAL LOGIC - SMT
8
HMC722LC3C
v04.0313
GATE, w/ PROGRAMMABLE OUTPUT VOLTAGE
13 Gbps, FAST RISE TIME AND/NAND/OR/NOR
Application Circuit
