CRA06E0831K10JTA - Vishay [Dale]

Thick Film Resistor Array

www.vishay.com For technical questions, contact: filmresistors.thickfilmchip@vishay.com Document Number: 31002

252 Revision: 13-Oct-08

CRA06E, CRA06S

Vishay

CRA06E and CRA06S Thick Film resistor arrays are

constructed on a high grade ceramic body with convex

terminations. A small package enables the design of high

density circuits. The single component reduces board space,

component counts and assembly costs.

FEATURES

•Convex terminal array available with either

scalloped corners (E version) or square corners

(S version)

•Wide ohmic range: 10R to 1M0

•4 or 8 terminal package with isolated resistors

•Lead (Pb)-free solder contacts on Ni barrier layer

•Pure tin plating provides compatibility with Lead (Pb)-free

and lead containing soldering processes

•Compatible with "Restriction of the use of Hazardous

Substances" (RoHS) directive 2002/95/EC (issue 2004)

Notes

(1) Rated voltage:

(2) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the

printed-circuit board (thermal resistance). The rates dissipation applies only if the permitted film temperature of 155 °C is not exceed.

Notes

(3) Preferred way for ordering products is by use of the PART NUMBER

(4) Please refer to table PACKAGING, see next page

STANDARD ELECTRICAL SPECIFICATIONS

MODEL CIRCUIT

POWER RATING

P70 °C

LIMITING ELEMENT

VOLTAGE MAX.

V≅

TEMPERATURE

COEFFICIENT

ppm/K

TOLERANCE

RESISTANCE

RANGE

E-SERIES

CRA06E

CRA06S 03 0.063 50 ± 100 ± 1 10R - 1M0 24 + 96

± 200 ± 2; ± 5 24

Zero-Ohm-Resistor available; Rmax. = 50 mΩ, Imax. = 1 A

TECHNICAL SPECIFICATIONS

PARAMETER UNIT CRA06E & S

Rated Dissipation at 70 °C (2) W per element 0.063

Limiting Element Voltage (1) V≅50

Insulation Voltage (1 min) Vdc/ac peak 100

Category Temperature Range °C - 55 to + 155

Insulation Resistance Ω> 109

PR×

TOLERANCE

F = ± 1 %

G = ± 2 %

J = ± 5 %

Z = 0

Ω Ju mper

MODE L

CRA06

TERMINAL STYLE

SPECIAL

Up to 2 digits

PART NUMBER AND PRODUCT DESCRIPTION

PART NUMBER: CRA06S08347K0JTA (3)

CR A0 6 S 08 347K0JTA

PRODUCT DESCRIPTION: CRA06S 08 03 473 J RT1 e3

TERMINAL COUNT

TOLERANCE

F = ± 1 %

G = ± 2 %

J = ± 5 %

Z = 0 ΩJumper

CIRCUI T

3 = 03

CRA06S

MODEL

CRA06S

CRA06E

CIRCUIT TYPE

473

RESISTANCE VALUE

473 = 47 kΩ

4702 = 47 kΩ

10R0 = 10 Ω

100 = 10 Ω

000 = 0 Ω Jumper

VALU E

R = Decimal

K = Thousand

M = Millio n

0000 = 0 Ω Ju mpe r

LEAD (Pb)-FREE

e3 = Pure tin

Termination finish

RT1

RT6

First two digits (3 for 1 %)

are significant. Last

digit is the multiplier.

PACKAGING (4)

Document Number: 31002 For technical questions, contact: filmresistors.thickfilmchip@vishay.com www.vishay.com

Revision: 13-Oct-08 253

CRA06E, CRA06S

Thick Film Resistor Array Vishay

CIRCUIT

DIMENSIONS

AVAILABLE TYPES AND RANGES

MODEL TERMINAL COUNT CIRCUIT TEMPERATURE

COEFFICIENT TOLERANCE

CRA06S

04 03 ± 100 ppm/K ± 1 %

± 200 ppm/K ± 5 %; ± 2 %

08 03 ± 100 ppm/K ± 1 %

± 200 ppm/K ± 5 %; ± 2 %

CRA06E 08 03 ± 100 ppm/K ± 1 %

± 200 ppm/K ± 5 %; ± 2 %

PACKAGING

MODEL TAPE WIDTH DIAMETER PITCH PIECES/REEL

PACKAGING CODE

PAP ER TA PE

PART NUMBER PRODUCT DESCRIPTION

CRA06 8 mm 180 mm/7" 4 mm 5000 TA RT1

330 mm/13" 4 mm 20 000 TC RT6

- 55 - 25 0 25 50 75 100 125 155 175

120

100

Derating Ambient Temperature in °C

Rated Power in %

03 CIRCUIT

4 pin 8 pin

E-Version

103

S-Version

PIN 1

ee a a

103

MODEL PIN

NO#

DIMENSIONS

[in millimeters]

LAA

BB*P T W

CRA06S 4

1.6 0.38 0.61 0.3 0.3 0.8 0.5 1.5

CRA06E 8

3.2 0.38 - 0.3 0.3 0.8 0.5 1.5

CRA06S 8

3.2 0.38 0.61 0.3 0.3 0.8 0.5 1.5

TOL.

± 0.15 ± 0.15 ± 0.15 ± 0.15 ± 0.15 ± 0.1 ± 0.1 ± 0.15

SOLDER PAD DIMENSIONS

[in millimeters]

MODEL PINScwdpabe

CRA06S

4 0.8 3.1 0.36 0.44 1.15

CRA06E

CRA06S

8 0.8 3.1 0.36 0.8 0.44 1.15 0.63

www.vishay.com For technical questions, contact: filmresistors.thickfilmchip@vishay.com Document Number: 31002

254 Revision: 13-Oct-08

CRA06E, CRA06S

Vishay Thick Film Resistor Array

Notes

(1) Figures are given for a single element

(2) Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years

TEST PROCEDURES AND REQUIREMENTS

EN 60115-1

TEST

(clause) CONDITIONS OF TEST

REQUIREMENTS

PERMISSIBLE CHANGE (ΔR/R) (1)

STABILITY

CLASS 1 OR BETTER

STABILITY

CLASS 2 OR BETTER

Stability for product types:

10 Ω to 1 MΩ10 Ω to 1 MΩ

CRA06E/CRA06S

Resistance (4.5) - ± 1 %± 2 %; ± 5 %

Temperature coefficient (4.8.4.2) 20/- 55/20 °C and

20/125/20 °C ± 100 ppm/K ± 200 ppm/K

Overload (4.13) U = 2.5 × (P70 x R)1/2

≤ 2 x Umax.; 0.5 s ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω)

Solderability (4.17.5) (2)

Aging 4 h at 155 °C, dryheat

solder bath method; 235 °C; 2 s

visual examination

Good tinning (≥ 95 % covered)

no visible damage

Resistance to soldering heat (4.18.2) Solder bath method;

(260 ± 5) °C; (10 ± 1) s ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω)

Rapid change of temperature (4.19) 30 min at LCT = - 55 °C;

30 min at UCT = 125 °C; 5 cycles ± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω)

Damp heat, steady state (4.24) (40 ± 2) °C; 56 days;

(93 ± 3) % RH ± (1 % R + 0.05 Ω)± (2 % R + 0.1 Ω)

Climatic sequence (4.23)

16 h at UCT = 125 °C; 1 cycle at 55 °C;

2 h at LCT = - 55 °C;

1 h/1 kPa at 15 °C to 35 °C;

5 cycles at 55 °C

U = (P70 x R)1/2

U = Umax.; whichever is less severe

± (1 % R + 0.05 Ω)± (2 % R + 0.1 Ω)

Endurance at 70 °C (4.25.1)

U = (P70 x R)1/2

U = Umax.; whichever is less severe

1.5 h ON; 0.5 h OFF;

70 °C; 1000 h

± (1 % R + 0.05 Ω)± (2 % R + 0.1 Ω)

Extended endurance (4.25.1.8) Duration extended to 8000 h ± (2 % R + 0.1 Ω)± (4 % R + 0.1 Ω)

Endurance at upper category

temperature (4.25.3) UCT = 125 °C; 1000 h ± (1 % R + 0.05 Ω)± (2 % R + 0.1 Ω)

APPLICABLE SPECIFICATIONS

• EN 60115-1 Generic Specification

• EN 140400 Sectional Specification

• EN 140401-802 Detail Specification

• IEC 60068-2-X Variety of environmental test procedures

• EIA 481 Packaging of SMD components

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 12-Mar-12 1Document Number: 91000

Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical

requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements

about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular

product with the properties described in the product specification is suitable for use in a particular application. Parameters

provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All

operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree

to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and

damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay

or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to

obtain written terms and conditions regarding products designed for such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by

any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Material Category Policy

Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the

definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council

of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment

(EEE) - recast, unless otherwise specified as non-compliant.

Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that

all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.