Aluminum electrolytic capacitors Capacitors with screw terminals Series/Type: / : B43310, B43330 - Standard industrial - 85 C B43310, B43330 - - 85 C Date: : August 2007 2007 8 EPCOS (Xiamen) Co., Ltd 2007. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. EPCOS 2007 EPCOS Page 1 of 13 Capacitors with screw terminals Standard industrial - 85 C B43310, B43330 General purpose grade capacitors Applications Uninterruptible power supplies Frequency converters B43310 B43330 Features All-welded construction ensures reliable electrical contact High reliability and high ripple current capability Construction Charge-discharge proof, polar Aluminum case with insulating sleeve Poles with screw terminal connections Mounting with ring clips, clamps or threaded stud / The bases of types with threaded stud and d 76.9 mm are not insulated, types with d = 91.0 mm have fully insulated bases. d 76.9 mm 91.0 mm Please read Cautions & warnings and Important notes at the end of this document. . Published by EPCOS (Xiamen) Co., Ltd EPCOS Page 2 of 13 B43310, B43330 Standard industrial - 85 C Specifications and characteristics in brief Rated voltage VR VR 400 ... 450 V DC Surge voltage VS VS 1.10 * VR Rated capacitance CR CR 1800 ... 15000 F Capacitance tolerance 20% M Leakage current Ileak Ileak (20 C, 5 minutes) 0.008 C*V [A] or 5 mA whichever is smaller 0.008 C*V [A] 5 mA tan max. (20 C, 120 Hz) max. (20 C, 120 Hz) 0.2 C = Rated Capacitance [F], V = Rated Voltage [V] C = [F], V = [V] C/C Load life 85 C; VR; IAC,R 2000 h () tan Not more than 175% of specified value 175% Ileak Vibration resistance test Less than 15% of initial value 15% Less than specified value To IEC 60068-2-6, test Fc: Displacement amplitude 0.75 mm, frequency range 10 ... 55 Hz, acceleration max. 10 g, duration 3 x 2 h. Capacitor mounted by its body which is rigidly clamped to the work surface. IEC 60068-2-6 Fc : 0.75 mm10 ... 55 Hz 10 g3 X 2h IEC climatic category IEC To IEC 60068-1: 25/085/56 (-25 C/+85 C/56 days damp heat test) IEC 60068-1: 25/085/56-25 C/+85 C/56 , Detail specification Similar to CECC 30301-810 CECC 30301-810 Sectional specification IEC 60384-4 Please read Cautions & warnings and Important notes at the end of this document. . Published by EPCOS (Xiamen) Co., Ltd EPCOS Page 3 of 13 B43310, B43330 Standard industrial - 85 C Ripple current capability Due to the ripple current capability of the contact elements, the following current upper limits must not be exceeded: Capacitor diameter d d 51.6 mm 64.3 mm 76.9 mm 91.0 mm IAC,max 34 A 45 A 57 A 80 A Dimensional drawings B43310 Ring clip/clamp mounting B43330 Threaded stud mounting l1 l1 l l M5: Min. reach of screw = 8 mm M6: Min. reach of screw = 10 mm KAL1127-X-E a od 1 a + od 2 od 2 d l2 KAL0989-W Positive pole marking: + For B43330 capacitors with threaded stud and d 76.9 mm the base is not insulated. For details, refer to "Data Book 2007 - Aluminum Electrolytic Capacitors", B43330 d 76.9 mm "2007 " Dimension and weights Dimensionsmmwith insulating sleeves (mm) Terminal d l +3/-0 l1 +3/-0 l2 +0/-1 d1 d2 max. a +0.2/-0.4 Approx. weight (g) M5 51.6 +0/-0.8 130 136.5 17 M12 11.4 22.2 350 M5 M5 64.3 +0/-0.8 64.3 +0/-0.8 96 115 102.5 121.5 17 17 M12 M12 13.2 13.2 28.5 28.5 400 490 M5 64.3 +0/-0.8 130 136.5 17 M12 13.2 28.5 540 M6 M6 76.9 +0/-0.7 76.9 +0/-0.7 115 130 120.8 135.8 17 17 M12 M12 17.7 17.7 31.7 31.7 620 770 M6 76.9 +0/-0.7 155 160.8 17 M12 17.7 31.7 990 M6 M6 91.0 +0/-2 91.0 +0/-2 157 196 162.5 201.5 17 17 M12 M12 17.7 17.7 31.7 31.7 1400 1600 M6 91.0 +0/-2 220 225.5 17 M12 17.7 31.7 1900 Please read Cautions & warnings and Important notes at the end of this document. . Published by EPCOS (Xiamen) Co., Ltd EPCOS Page 4 of 13 B43310, B43330 Standard industrial - 85 C Packing Capacitor diameter d d Packing units (pcs.) 51.6 mm 22 64.3 mm 15 76.9 mm 12 91.0 mm 8 For ecological reasons the packing is pure cardboard. Accessories The following items are included in the delivery package, but are not fastened to the capacitors: For terminals For mounting M5 A 5.1 DIN 6797 Cylinder-head screw M5 x 8 DIN 84-4.8 M5 x 8 DIN 84-4.8 2.0 Nm M6 A 6.4 DIN 6797 Cylinder-head screw M6 x 10 DIN 85-4.8 M6 x 10 DIN 85-4.8 2.5 Nm M12 J 12.5 DIN 6797 Hex nut BM 12 DIN 439 BM 12 DIN 439 10 Nm The following items must be ordered separately. For details, refer to "Data Book 2007 - Aluminum Electrolytic Capacitors", chapter "Screw terminals - Accessories". "2007 """ Item Type Ring clips B44030 Clamps for capacitors with d 64.3 mm d 64.3 mm B44030 Insulating parts B44020 Please read Cautions & warnings and Important notes at the end of this document. . Published by EPCOS (Xiamen) Co., Ltd EPCOS Page 5 of 13 B43310, B43330 Standard industrial - 85 C Technical data and ordering codes CR 120 Hz 20 C F Case dimensions dxl mm ESRtyp 120 Hz 20 C m IAC,max 120 Hz 40 C A IAC,R 120 Hz 85 C A Ordering code (composition see below) VR = 400 V DC 2200 51.6 x 130 2200 64.3 x 96 2700 64.3 x 96 3300 64.3 x 115 3900 64.3 x 130 4700 76.9 x 115 5600 76.9 x 130 6800 76.9 x 155 8200 91.0 x 157 10000 91.0 x 157 12000 91.0 x 196 15000 91.0 x 220 VR = 450 V DC 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 51.6 x 130 64.3 x 96 64.3 x 115 64.3 x 130 76.9 x 115 76.9 x 130 76.9 x 155 91.0 x 157 91.0 x 157 91.0 x 196 91.0 x 220 87 87 71 58 49 41 34 28 23 19 16 13 17.3 17.0 18.9 22.6 25.8 28.5 32.5 38.8 44.7 49.2 59.6 69.7 6.5 6.4 7.1 8.5 9.7 10.7 12.2 14.6 16.8 18.5 22.4 26.2 B433*0A9228M000 B433*0C9228M000 B433*0A9278M000 B433*0A9338M000 B433*0A9398M000 B433*0A9478M000 B433*0A9568M000 B433*0A9688M000 B433*0A9828M000 B433*0A9109M000 B433*0A9129M000 B433*0A9159M000 102 83 68 55 49 41 34 28 23 19 16 16.0 17.3 20.7 24.2 25.8 29.8 35.4 40.7 44.7 54.3 62.5 6.0 6.5 7.8 9.1 9.7 11.2 13.3 15.3 16.8 20.4 23.5 B433*0A5188M000 B433*0A5228M000 B433*0A5278M000 B433*0A5338M000 B433*0A5398M000 B433*0A5478M000 B433*0A5568M000 B433*0A5688M000 B433*0A5828M000 B433*0A5109M000 B433*0A5129M000 Composition of ordering code * = Mounting style 1 = for capacitors with ring clip/clamp mounting / 3 = for capacitors with threaded stud Please read Cautions & warnings and Important notes at the end of this document. . Published by EPCOS (Xiamen) Co., Ltd EPCOS Page 6 of 13 B43310, B43330 Standard industrial - 85 C Load life depending on ambient temperature TA under ripple current operating conditions , KAL1126-P 3.0 B43310/330 I AC I AC,R 2.5 2.0 1.5 0 40 50 60 70 2000 h 5000 h 10000 h 25000 h 0.5 50000 h 100000 h 1.0 80 C TA 90 Frequency factor of permissible ripple current IAC versus frequency f IAC f KAL1125-G 1.6 B43310/330 I AC, f I AC, 120 Hz 1.2 1.0 0.8 0.6 0.4 0.2 1 10 10 2 10 3 Hz 10 4 f Please read Cautions & warnings and Important notes at the end of this document. . Published by EPCOS (Xiamen) Co., Ltd EPCOS Page 7 of 13 Cautions and warnings Personal safety The electrolytes used by EPCOS have not only been optimized with a view to the intended application, but also with regard to health and environmental compatibility. They do not contain any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide (DMAC). Furthermore, part of the high-voltage electrolytes used by EPCOS is self-extinguishing. They contain flame-retarding substances which will quickly extinguish any flame that may have been ignited. As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce operating electrolytes. However, in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no safe substitute materials are currently known. However, the amount of dangerous materials used in our products has been limited to an absolute minimum. Nevertheless, the following rules should be observed when handling Al electrolytic capacitors: Any escaping electrolyte should not come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected parts immediately with running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical treatment. Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be well ventilated. Clothing that has been contaminated by electrolyte must be changed and rinsed in water. (EPCOS) DMFDMAC Published by EPCOS (Xiamen) Co., Ltd EPCOS Page 8 of 13 Cautions and warnings Product safety The table below summarizes the safety instructions that must be observed without fail. A detailed description can be found in the relevant sections of Data Book 2007 - Aluminum Electrolytic Capacitors, chapter "General technical information". Topic Safety Information Reference Chapter `General technical information" Polarity Make sure that polar capacitors are connected with the right polarity. 1 "Basic construction of aluminum electrolytic capacitors" Reverse voltage Voltages polarity classes should be prevented by connecting a diode. 3.1.6 "reverse voltage" Upper category temperature Do not exceed the upper category temperature. 7.2 "Maximum permissible operating temperature" Maintenance Make periodic inspections of the capacitors. Before the inspection, make sure that the power supply is turned off and carefully discharge the electricity of the capacitors. Do not apply any mechanical stress to the capacitor terminals. 10 "Maintenance" Mounting position of screw terminal capacitors Do not mount the capacitor with the terminals (safety vent) upside down. 11.1. "Mounting positions of capacitors with screw terminals" Mounting of single-ended capacitors The internal structure of singleended capacitors might be damaged if excessive force is applied to the lead wires. Avoid any compressive, tensile or flexural stress. Do not move the capacitor after soldering to PC board. 11.4 "Mounting considerations for single-ended capacitors" Robustness of terminals The following maximum tightening torques must not be exceeded when connecting screw terminals: M5: 2 Nm M6: 2.5 Nm 11.3 "Mounting torques" Soldering Do not exceed the specified time or temperature limits during soldering. 11.5 "Soldering" Published by EPCOS (Xiamen) Co., Ltd EPCOS Page 9 of 13 Cautions and warnings Topic Safety Information Reference Chapter `General technical information" Soldering, cleaning agents Do not allow halogenated hydrocarbons to come into contact with aluminum electrolytic capacitors. 11.6 "Cleaning agents" Passive flammability Avoid external energy, such as fire or electricity. 8.1 "Passive flammability" Active flammability Avoid overload of the capacitors 8.2 "Active flammability" Reference Chapter `Capacitors with screw terminals" Breakdown strength of insulating sleeves. Published by EPCOS (Xiamen) Co., Ltd EPCOS Do not damage the insulating sleeve, especially when ring clips are used for mounting. Page 10 of 13 "Screw terminals - accessories" Cautions and warnings 2007"" M5: 2 Nm M6: 2.5 Nm Published by EPCOS (Xiamen) Co., Ltd EPCOS Page 11 of 13 " " 1 " " 3.1.6 "" 7.2 " " 10 "" 11.1 " " 11.4 " " 11.3 "" 11.5 "" 11.6 "" 8.1 "" 8.2 "" " " "-- --" Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as "hazardous"). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the "General Terms of Delivery for Products and Services in the Electrical Industry" published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, MiniBlue, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Published by EPCOS (Xiamen) Co., Ltd EPCOS Page 12 of 13 Important notes 1 2 3 4 " " www.epcos.com/material"" 5 6 " ZVEI " 7 EPCOSBAOKEAlu-XCeraDiodeCSSPMLSCMiniBlue MKKMotorCap PCCPhaseCapPhaseModSIFERRITSIFISIKORELSilverCapSIMDADSIMID SineFormer SIOV SIP5DSIP5KThermoFuse WindCap www.epcos.com/trademarks Published by EPCOS (Xiamen) Co., Ltd EPCOS Page 13 of 13