ASM707CPA-T - ON Semiconductor L.L.C.

August, 2011 − Rev. 3

1Publication Order Number:

ASM705/D

ASM705, ASM706, ASM707,

ASM708, ASM813L

Low Power mP Supervisor

Circuits

Description

The ASM705 / 706 / 707 / 708 and ASM813L are cost effective

CMOS supervisor circuits that monitor power−supply and battery

voltage level, and mP/mC operation.

The family offers several functional options. Each device generates

a reset signal during power−up, power−down and during brownout

conditions. A reset is generated when the supply drops below 4.65 V

(ASM705/707/813L) or 4.40 V (ASM706/708). For 3 V power supply

applications, refer to the ASM705P/R/S/T data sheet. In addition, the

ASM705/706/813L feature a 1.6 second watchdog timer. The

ASM707/708 have both active−HIGH and active−LOW reset outputs

but no watchdog function. The ASM813L has the same pin−out and

functions as the ASM705 but has an active−HIGH reset output. A

versatile power−fail circuit has a 1.25 V threshold, useful in low

battery detection and for monitoring non−5 V supplies. All devices

have a manual reset (MR) input. The watchdog timer output will

trigger a reset if connected to MR.

All devices are available in 8−pin DIP, SO and MicroSO packages.

Features

•Precision Power Supply Monitor

4.65 V Threshold (ASM705/707/813L)

4.40 V Threshold (ASM706/708)

•Debounced Manual Reset Input

•Voltage Monitor

1.25 V Threshold

Battery Monitor / Auxiliary Supply Monitor

•Watchdog Timer (ASM705/706/813L)

•200 ms Reset Pulse Width

•Active HIGH Reset Output (ASM707/708/813L)

•MicroSO Package

Applications

•Computers and Embedded Controllers

•Portable/Battery−operated Systems

•Intelligent Instruments

•Wireless Communication Systems

•PDAs and Hand−held Equipment

•Automotive Systems

•Safety Systems

http://onsemi.com

PIN CONFIGURATIONS

See detailed ordering and shipping information in the package

dimensions section on page 11 of this data sheet.

ORDERING INFORMATION

PDIP−8

P SUFFIX

CASE 646AA

SOIC−8

S SUFFIX

CASE 751BD

VCC

GND

PFI

RESET

PFO

ASM707

ASM708

VCC

GND

PFI

WDO

RESET (RESET)

WDI

PFO

ASM705

ASM706

(ASM813L)

DIP/SO

(Top Views)

MICRO−8

U SUFFIX

CASE 846AA

MicroSO

(Top Views)

RESET

VCC

PFI

GND

PFO

RESET (RESET)

WDO

VCC

WDI

PFI

GND

PFO

ASM707

ASM708

ASM705

ASM706

(ASM813L)

ASM705, ASM706, ASM707, ASM708, ASM813L

http://onsemi.com

Figure 1. Typical Operating Circuit

Figure 2. Block Diagrams

ASM705, ASM706, ASM707, ASM708, ASM813L

http://onsemi.com

Table 1. PIN DESCRIPTION

Pin Number

ASM705/706 ASM707/708 ASM813L

DIP/

SO MicroSO

DIP/

SO MicroSO

DIP/

SO MicroSO Name Function

1 3 1 3 1 3 MR Manual reset input. The active LOW input triggers a

reset pulse. A 250 mA pull−up current allows the pin

to be driven by TTL/CMOS logic or shorted to

ground with a switch.

2 4 2 4 2 4 VCC +5 V power supply input.

3 5 3 5 3 5 GND Ground reference for all signals.

4 6 4 6 4 6 PFI Power−fail input voltage monitor. With PFI less than

1.25 V, PFO goes LOW. Connect PFI to Ground or

VCC when not in use.

5 7 5 7 5 7 PFO Power−fail output. The output is active LOW and

sinks current when PFI is less than 1.25 V.

6 8 − − 6 8 WDI Watchdog input. WDI controls the internal watchdog

timer. A HIGH or LOW signal for 1.6 sec at WDI

allows the internal timer to run−out, setting WDO

LOW. The watchdog function is disabled by floating

WDI or by connecting WDI to a high impedance

three−state buffer. The internal watchdog timer

clears when: RESET is asserted; WDI is three−

stated; or WDI sees a rising or falling edge.

− − 6 8 − − NC Not Connected.

7 1 7 1 − − RESET Active LOW reset output. Pulses LOW for 200 ms

when triggered, and stays LOW whenever VCC is

below the reset threshold. RESET remains LOW for

200 ms after VCC rises above the reset threshold or

MR goes from LOW to HIGH. A watchdog timeout

will not trigger RESET unless WDO is connected to

MR.

8 2 − − 8 2 WDO Watchdog output. WDO goes LOW when the 1.6

second internal watchdog timer times−out and does

not go HIGH until the watchdog is cleared. In addi-

tion, when VCC falls below the reset threshold,

WDO goes LOW. Unlike RESET, WDO does not

have a minimum pulse width and as soon as VCC

exceeds the reset threshold, WDO goes HIGH with

no delay.

− − 8 2 7 1 RESET Active HIGH reset output. The inverse of RESET.

The ASM813L only has a RESET output.

ASM705, ASM706, ASM707, ASM708, ASM813L

http://onsemi.com

Table 2. ABSOLUTE MAXIMUM RATINGS

Parameter Min Max Unit

Pin Terminal Voltage with Respect to Ground

VCC

All other inputs (Note 1)

Input Current at VCC and GND

−0.3

6.0

VCC + 0.3

Output Current: All outputs 20 mA

Rate of Rise at VCC 100 V/ms

Plastic DIP Power Dissipation (Derate 9 mW/°C above 70°C) 700 mV

SO Power Dissipation (Derate 5.9 mW/°C above 70°C) 470 mW

MicroSO Power Dissipation (Derate 4.1 mW/°C above 70°C) 330 mW

Operating Temperature Range

ASM705E/706E/707E/708E/813LE

ASM705C/706C/707C/708C/813LC

−40

+85

°C

Storage Temperature Range −65 160 °C

Lead Temperature (Soldering 10 sec) 300 °C

ESD rating

HBM

200

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the

Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect

device reliability.

1. The input voltage limits of PFI and MR can be exceeded if the input current is less than 10 mA.

ASM705, ASM706, ASM707, ASM708, ASM813L

http://onsemi.com

Table 3. ELECTRICAL CHARACTERISTICS

Unless otherwise noted, specifications are over the operating temperature range and VCC supply voltages are 2.7 V to 5.5 V

(ASM706P,ASM708R), 3.0 V to 5.5 V (ASM706/708S), 3.15 V to 5.5 V (ASM706/708T) and 4.1 V to 5.5 V (ASM706/708J).

Parameter Symbol Test Conditions Min Typ Max Unit

Operating Voltage Range VCC ASM705/6/7/8C 1.2 5.5 V

ASM813L 1.1 5.5

ASM705/6/7/8E, ASM813E 1.2 5.5

Supply Current ICC ASM705/706C/813LC 75 140 mA

ASM705E/706E/813LE 75 140

ASM707C/708C 50 140

ASM707E/708E 50 140

RESET Threshold VRT ASM705/707/813L (Note 2) 4.50 4.65 4.75 V

ASM706/708 (Note 2) 4.25 4.40 4.50

RESET Threshold

Hysteresis

(Note 2) 40 mV

RESET Pulse Width tRS (Note 2) 140 200 280 ms

MR Pulse Width tMR 0.15 ms

MR to RESET Out Delay tMD (Note 2) 0.25 ms

MR Input Threshold VIH 2.0 V

VIL 0.8

MR Pullup current MR = 0 V 100 250 600 mA

RESET Output Voltage ISOURCE = 800 mAVCC − 1.5 V

ISINK = 3.2 mA 0.4

ASM705/6/7/8, VCC = 1.2 V,

ISINK = 100 mA

0.3

RESET Output Voltage ASM707/8/813L, ISOURCE = 800 mAVCC − 1.5 V

ASM707/8, ISINK = 1.2 mA 0.4

ASM813L, ISINK = 3.2 mA 0.4

ASM813L, VCC = 1.2 V, ISOURCE = 4 mA0.9

Watchdog Timeout Period tWD ASM705/6/813L 1.00 1.60 2.25 S

WDI Pulse Width tWP VIL = 0.4 V, VIH = 0.8 VCC 50 ns

WDI Input Threshold VIH ASM705/706/813L, VCC = 5 V 3.5 V

VIL 0.8

WDI Input Current ASM705/6/813L, WDI = VCC 50 150 mA

ASM705/6/813L, WDI = 0 V −150 −50

WDO Output Voltage VOH ASM705/6/813L, ISOURCE = 800 mAVCC − 1.5 V

VOL ASM705/6/813L, ISINK = 1.2 mA 0.4

PFI Input Threshold VCC = 5 V 1.2 1.25 1.3 V

PFI Input Current −25 0.01 25 nA

PFO Output Voltage VOH ISOURCE = 800 mAVCC − 1.5 V

VOL ISINK = 3.2 mA 0.4

2. RESET (ASM705/6/7/8), RESET(ASM707/8, ASM813L)

ASM705, ASM706, ASM707, ASM708, ASM813L

http://onsemi.com

Detailed Description

A proper reset input enables a microprocessor /

microcontroller to start in a known state. ASM70X and

ASM813L assert reset to prevent code execution errors

during power−up, power−down and brown−out conditions.

RESET/RESET Timing

The RESET/RESET signals are designed to start a mP/mC

in a known state or return the system to a known state.

The ASM707/708 have two reset outputs, one

active−HIGH RESET and one active−LOW RESET output.

The ASM813L has only an active−HIGH output. RESET is

simply the complement of RESET.

RESET is guaranteed to be LOW with VCC above 1.2 V.

During a power−up sequence, RESET remains low until

the supply rises above the threshold level, either 4.65 V or

4.40 V. RESET goes high approximately 200 ms after

crossing the threshold.

During power−down, RESET goes LOW as VCC falls

below the threshold level and is guaranteed to be under 0.4 V

with VCC above 1.2 V.

In a brownout situation where VCC falls below the

threshold level, RESET pulses low. If a brown−out occurs

during an already initiated reset, the pulse will continue for

a minimum of 140 ms.

Power Failure Detection with Auxiliary Comparator

All devices have an auxiliary comparator with 1.25 V trip

point and uncommitted output (PFO) and noninverting input

(PFI). This comparator can be used as a supply voltage

monitor with an external resistor voltage divider. The

attenuated voltage at PFI should be set just below the 1.25

threshold. As the supply level falls, PFI is reduced causing

the PFO output to transit LOW. Normally PFO interrupts the

processor so the system can be shut down in a controlled

manner.

Figure 3. WDI Three−state Operation

Manual Reset (MR)

The active−LOW manual reset input is pulled high by a

250 mA pull−up current and can be driven low by

CMOS/TTL logic or a mechanical switch to ground. An

external debounce circuit is unnecessary since the 140 ms

minimum reset time will debounce mechanical pushbutton

switches.

By connecting the watchdog output (WDO) and MR, a

watchdog timeout forces RESET to be generated. The

ASM813L should be used when an active−HIGH RESET is

required.

Watchdog Timer

The watchdog timer available on the ASM705/706/813L

monitors mP/mC activity. An output line on the processor is

used to toggle the WDI line. If this line is not toggled within

1.6 seconds, the internal timer puts the watchdog output,

WDO, into a LOW state. WDO will remain LOW until a

toggle is detected at WDI.

If WDI is floated or connected to a three−stated circuit, the

watchdog function is disabled, meaning, it is cleared and not

counting. The watchdog timer is also disabled if RESET is

asserted. When RESET becomes inactive and the WDI input

sees a high or low transition as short as 50 ns, the watchdog

timer will begin a 1.6 second countdown. Additional

transitions at WDI will reset the watchdog timer and initiate

a new countdown sequence.

WDO will also become LOW and remain so, whenever

the supply voltage, VCC, falls below the device threshold

level. WDO goes HIGH as soon as VCC transitions above the

threshold. There is no minimum pulse width for WDO as

there is for the RESET outputs. If WDI is floated, WDO

essentially acts as a low−power output indicator.

Figure 4. Watchdog Timing

ASM705, ASM706, ASM707, ASM708, ASM813L

http://onsemi.com

Application Information

Ensuring That RESET is Valid Down to VCC = 0 V

When VCC falls below 1.1 V, the ASM705−708 RESET

output no longer pulls down; it becomes indeterminate. To

avoid the possibility that stray charges build up and force

RESET to the wrong state, a pull−down resistor should be

connected to the RESET pin, thus draining such charges to

ground and holding RESET low. The resistor value is not

critical. A 100 kW resistor will pull RESET to ground

without loading it.

Bi−directional Reset Pin Interfacing

The ASM705/6/7/8 can interface with mP/mC

bi−directional reset pins by connecting a 4.7 kW resistor in

series with the RESET output and the mP/mC bi−directional

RESET pin.

Figure 5. Bi−directional Reset Pin Interfacing

Monitoring Voltages Other Than VCC

The ASM705−708 can monitor voltages other than VCC

using the Power Fail circuitry. If a resistive divider is

connected from the voltage to be monitored to the Power

Fail input (PFI), the PFO will go LOW if the voltage at PFI

goes below 1.25 V reference. Should hysteresis be desired,

connect a resistor (equal to approximately 10 times the sum

of the two resistors in the divider) between the PFI and PFO

pins. A capacitor between PFI and GND will reduce circuit

sensitivity to input high−frequency noise. If it is desired to

assert a RESET for voltages other than VCC then the PFO

output is to be connected to the MR.

Figure 6. Monitoring +5 V and an

Additional Supply VIN

Monitoring a Negative Voltage

The Power−Fail circuitry can also monitor a negative

supply rail. When the negative rail is OK, PFO will be LOW,

and when the negative rail is failing (not negative enough),

PFO goes HIGH (the opposite of when positive voltages are

monitored). To trigger a reset, these outputs need to be

inverted: adding the resistors and transistor as shown

achieves this. The RESET output will then have the same

sense as for positive voltages: good = HIGH, bad = LOW. It

should be noted that this circuit’s accuracy depends on the

VCC line, the PFI threshold tolerance, and the resistors.

Figure 7. Monitoring a Negative Voltage

ASM705, ASM706, ASM707, ASM708, ASM813L

http://onsemi.com

PACKAGE DIMENSIONS

Micro8t/TSSOP8 3x3

CASE 846AA−01

ISSUE O

0.08 (0.003) A S

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE

BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED

0.15 (0.006) PER SIDE.

4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION.

INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE.

5. 846A-01 OBSOLETE, NEW STANDARD 846A-02.

PIN 1 ID

8 PL

0.038 (0.0015)

−T−

SEATING

PLANE

A1 cL

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

8X 8X

6X ǒmm

inchesǓ

SCALE 8:1

1.04

0.041

0.38

0.015

5.28

0.208

4.24

0.167

3.20

0.126

0.65

0.0256

DIM

MIN NOM MAX MIN

MILLIMETERS

−− −− 1.10 −−

INCHES

A1 0.05 0.08 0.15 0.002

b0.25 0.33 0.40 0.010

c0.13 0.18 0.23 0.005

D2.90 3.00 3.10 0.114

E2.90 3.00 3.10 0.114

e0.65 BSC

L0.40 0.55 0.70 0.016

−− 0.043

0.003 0.006

0.013 0.016

0.007 0.009

0.118 0.122

0.026 BSC

0.021 0.028

NOM MAX

4.75 4.90 5.05 0.187 0.193 0.199

ASM705, ASM706, ASM707, ASM708, ASM813L

http://onsemi.com

PACKAGE DIMENSIONS

PDIP−8, 300 mils

CASE 646AA−01

ISSUE A

TOP VIEW

SIDE VIEW END VIEW

PIN # 1

IDENTIFICATION

Notes:

(1) All dimensions are in millimeters.

(2) Complies with JEDEC MS-001.

SYMBOL MIN NOM MAX

0.38

2.92

0.36

6.10

1.14

0.20

9.02

2.54 BSC

3.30

5.33

4.95

0.56

7.11

1.78

0.36

10.16

eB 7.87 10.92

E 7.62 8.25

2.92 3.80

3.30

0.46

6.35

1.52

0.25

9.27

7.87

ASM705, ASM706, ASM707, ASM708, ASM813L

http://onsemi.com

PACKAGE DIMENSIONS

SOIC 8, 150 mils

CASE 751BD−01

ISSUE O

E1 E

PIN # 1

IDENTIFICATION

TOP VIEW

SIDE VIEW END VIEW

Notes:

(1) All dimensions are in millimeters. Angles in degrees.

(2) Complies with JEDEC MS-012.

SYMBOL MIN NOM MAX

0º 8º

0.10

0.33

0.19

0.25

4.80

5.80

3.80

1.27 BSC

1.75

0.25

0.51

0.25

0.50

5.00

6.20

4.00

L0.40 1.27

1.35

ASM705, ASM706, ASM707, ASM708, ASM813L

http://onsemi.com

Table 4. ORDERING INFORMATION − Tin − Lead Devices

Part Number (Note 3) Reset Threshold (V) Temperature (5C) Pins−Package Package Marking

ASM705 Active LOW Reset, Watchdog Output And Manual RESET

ASM705CPA 4.65 0°C to +70°C 8−Plastic DIP ASM705CPA

ASM705CSA 4.65 0°C to +70°C 8−SO ASM705CSA

ASM705CUA 4.65 0°C to +70°C 8−MicroSO ASM705CUA

ASM705EPA 4.65 −40°C to +85°C 8−Plastic DIP ASM705EPA

ASM705ESA 4.65 −40°C to +85°C 8−SO ASM705ESA

ASM705EUA 4.65 −40°C to +85°C 8−MicroSO ASM705EUA

ASM706 Active LOW Reset, Watchdog Output And Manual RESET

ASM706CPA 4.40 0°C to +70°C 8−Plastic DIP ASM706CPA

ASM706CSA 4.40 0°C to +70°C 8−SO ASM706CSA

ASM706CUA 4.40 0°C to +70°C 8−MicroSO ASM706CUA

ASM706EPA 4.40 −40°C to +85°C 8−Plastic DIP ASM706EPA

ASM706ESA 4.40 −40°C to +85°C 8−SO ASM706ESA

ASM707 Active LOW & HIGH Reset with Manual RESET

ASM707CPA 4.65 0°C to +70°C 8−Plastic DIP ASM707CPA

ASM707CSA 4.65 0°C to +70°C 8−SO ASM707CSA

ASM707CUA 4.65 0°C to +70°C 8−MicroSO ASM707CUA

ASM707EPA 4.65 −40°C to +85°C 8−Plastic DIP ASM707EPA

ASM707ESA 4.65 −40°C to +85°C 8−SO ASM707ESA

ASM708Active LOW & HIGH Reset with Manual RESET

ASM708CPA 4.40 0°C to +70°C 8−Plastic DIP ASM708CPA

ASM708CSA 4.40 0°C to +70°C 8−SO ASM708CSA

ASM708CUA 4.40 0°C to +70°C 8−MicroSO ASM708CUA

ASM708EPA 4.40 −40°C to +85°C 8−Plastic DIP ASM708EPA

ASM708ESA 4.40 −40°C to +85°C 8−SO ASM708ESA

ASM813L Active HIGH Reset, Watchdog Output And Manual RESET

ASM813LCPA 4.65 0°C to +70°C 8−Plastic DIP ASM813LCPA

ASM813LCSA 4.65 0°C to +70°C 8−SO ASM813LCSA

ASM813LCUA 4.65 0°C to +70°C 8−MicroSO ASM813LCUA

ASM813LEPA 4.65 −40°C to +85°C 8−Plastic DIP ASM813LEPA

ASM813LESA 4.65 −40°C to +85°C 8−SO ASM813LESA

3. For parts to be packed in Tape and Reel, add “−T” at the end of the part number.

ASM705, ASM706, ASM707, ASM708, ASM813L

http://onsemi.com

Table 5. ORDERING INFORMATION − Lead Free Devices

Part Number (Note 4) Reset Threshold (V) Temperature (5C) Pins−Package Package Marking

ASM705 Active LOW Reset, Watchdog Output And Manual RESET

ASM705CPAF 4.65 0°C to +70°C 8−Plastic DIP ASM705CPAF

ASM705CSAF 4.65 0°C to +70°C 8−SO ASM705CSAF

ASM705CUAF 4.65 0°C to +70°C 8−MicroSO ASM705CUAF

ASM705EPAF 4.65 −40°C to +85°C 8−Plastic DIP ASM705EPAF

ASM705ESAF 4.65 −40°C to +85°C 8−SO ASM705ESAF

ASM705EUAF 4.65 −40°C to +85°C 8−MicroSO ASM705EUAF

ASM706 Active LOW Reset, Watchdog Output And Manual RESET

ASM706CPAF 4.40 0°C to +70°C 8−Plastic DIP ASM706CPAF

ASM706CSAF 4.40 0°C to +70°C 8−SO ASM706CSAF

ASM706CUAF 4.40 0°C to +70°C 8−MicroSO ASM706CUAF

ASM706EPAF 4.40 −40°C to +85°C 8−Plastic DIP ASM706EPAF

ASM706ESAF 4.40 −40°C to +85°C 8−SO ASM706ESAF

ASM707 Active LOW & HIGH Reset with Manual RESET

ASM707CPAF 4.65 0°C to +70°C 8−Plastic DIP ASM707CPAF

ASM707CSAF 4.65 0°C to +70°C 8−SO ASM707CSAF

ASM707CUAF 4.65 0°C to +70°C 8−MicroSO ASM707CUAF

ASM707EPAF 4.65 −40°C to +85°C 8−Plastic DIP ASM707EPAF

ASM707ESAF 4.65 −40°C to +85°C 8−SO ASM707ESAF

ASM708Active LOW & HIGH Reset with Manual RESET

ASM708CPAF 4.40 0°C to +70°C 8−Plastic DIP ASM708CPAF

ASM708CSAF 4.40 0°C to +70°C 8−SO ASM708CSAF

ASM708CUAF 4.40 0°C to +70°C 8−MicroSO ASM708CUAF

ASM708EPAF 4.40 −40°C to +85°C 8−Plastic DIP ASM708EPAF

ASM708ESAF 4.40 −40°C to +85°C 8−SO ASM708ESAF

ASM813L Active HIGH Reset, Watchdog Output And Manual RESET

ASM813LCPAF 4.65 0°C to +70°C 8−Plastic DIP ASM813LCPAF

ASM813LCSAF 4.65 0°C to +70°C 8−SO ASM813LCSAF

ASM813LCUAF 4.65 0°C to +70°C 8−MicroSO ASM813LCUAF

ASM813LEPAF 4.65 −40°C to +85°C 8−Plastic DIP ASM813LEPAF

ASM813LESAF 4.65 −40°C to +85°C 8−SO ASM813LESAF

4. For parts to be packed in Tape and Reel, add “−T” at the end of the part number.

ASM705, ASM706, ASM707, ASM708, ASM813L

http://onsemi.com

Table 6. FEATURE SUMMARY

ASM705 ASM706 ASM707 ASM708 ASM813L

Power fail detector ♦♦♦♦♦

Brownout detection ♦♦♦♦♦

Manual RESET input ♦♦♦♦♦

Power−up/down RESET ♦♦♦♦♦

Watchdog Timer ♦ ♦ ♦

Active HIGH RESET output ♦ ♦ ♦

Active LOW RESET output ♦ ♦ ♦ ♦

RESET Threshold (V) 4.65 4.40 4.65 4.40 4.65

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice

to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All

operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights

nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications

intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should

Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,

and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death

associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal

Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

ASM705/D

PUBLICATION ORDERING INFORMATION

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81−3−5773−3850

LITERATURE FULFILLMENT:

Literature Distribution Center for ON Semiconductor

P.O. Box 5163, Denver, Colorado 80217 USA

Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada

Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

For additional information, please contact your local

Sales Representative