Data Sheet
April 5, 2006
QW010/015/020 Series Power Modules: dc-dc Converters;
36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Ou tput; 10 A to 20 A
Document Name: DS06-008 ver.1.3
PDF Name: QW010-015-020_ds.pdf
Applications
Q
Distributed Power Architectures
Q
Wireless Networks
Q
Access and Optical Network Equipment
Q
Enterprise Networks
Q
Latest generation IC’s (DSP, FPGA, ASIC) and Micropro-
cessor-powered applications.
Options
Q
Remote On/Off negative logic
Q
Surface-mount package (–S Suffix)
Q
Basic Insulation (–B Suffix)
Q
Baseplate version for heatsink attachment
(only Through-hole version)
Features
Q
Compatible with RoHS EU Directive 200295/EC (-Z Ver-
sions)
Q
Compatible in RoHS EU Directive 200295/EC with lead
solder exemption (non -Z versions)
Q
Delivers up to 20 A output current
Q
High efficiency: 91% at 3.3V full load (VIN = 48V)
Q
Small size and low profile:
36.8 mm x 57.9 mm x 8.50 mm
(1.45 in x 2.28 in x 0.335 in)
Q
Low output ripple and noise
Q
Exceptional thermal performance
Q
Industry standard "quarter-brick" footprint
Q
High reliability: MTBF > 3.1M hours at 25 °C
Q
Remote On/Off positive logic (primary referenced)
Q
Constant switching frequency (320 KHz typical)
Q
Remote Sense
Q
Output overvoltage and overcurrent protection
Q
Overtemperature protection
Q
Adjustable output voltage (± 10%)
Q
Meets the voltage and current requirements for
ETSI 300-132-2 and complies with an d is approved for
Basic Insulation rating per IEC609 50 3 rd (-B version
only)
Q
UL* 60950 Recogni zed, CSA† C22.2 No. 60950-00 Certi-
fied, and VDE‡ 0805 (IEC60950, 3rd edition) Licensed
Q
CE mark meets 73/23/EEC and 93/68/EEC directives§
Q
ISO** 9001 and ISO14001 certif ied manufacturing facili-
ties
RoHS Compliant
Description
The QW series power modul es are isola ted d c-dc co nverters that can de liver up to 20A of o utput cu rrent an d provide a pre-
cisely regulated o utput volt a ge over a w ide rang e of inpu t voltages (VI = 36Vdc to 75Vdc). The modules achi eve full l oad effi-
ciency of 91% at 3.3V output volt age, The open frame modules, availabl e in both surface-mount and through-hole p acka ging,
enable designers to develop cost- a nd sp ace-efficient solutions.
Standard features include remote On/Off, output voltage adjust-
ment, remote sense,overvoltage, overcurrent and overtemperature protection.
* UL is a registered trademark of Underwriters Laboratories, Inc.
†CSA is a registered trademark of Canadian Standards Association.
‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V.
§ This product is intended for integration into end-use equipment. All the required procedures for CE marking of end-use equipment should be followed. (The CE mark is placed on selected products.)
** ISO is a registered trademark of the Internation Organization of Standards
Tyco Electronics Power Systems 2
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress
ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the
operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the
device reliabiltiy.
Electrical Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions.
CAUTION: This power module is not internally fused. An input line fuse must always be used.
This power module can be used in a wide variety of application s , ranging from simple stand-alone operation to an integrated
part of a sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included however , to achieve
maximum safety and system protection, always use an input line fuse. The safety agencies require a time-delay fuse with a
maximum rating of 5 A (see Safety Considerations section). Based on the information provided in this data sheet on inrush
energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s
data sheet for further information.
Parameter Device Symbol Min Max Unit
Input Voltage:Continuous
Transient (100ms) All
All VI
VI, trans —
—75
100 Vdc
Vdc
Operating Ambient Temperature
(See Thermal Considerations section) All TA –40 85 °C
Storage Temperature All Tstg –55 125 °C
Parameter Device Symbol Min Typ Max Unit
Operating Input Voltage All VIN 36 48 75 Vdc
Maximum Input Current
(VI = 0 V to 75 V; IO = IO, max) All II, max — — 2.0 Adc
Inrush Transient All I2t0.2A
2s
Input Reflected Ripple Current, peak-peak
(5 Hz to 20 MHz, 12 µH source impedance
See Test configuration section )
All II 10 mAp-p
Input Ripple Rejection (120 Hz) All 50 dB
Tyco Electronics Power Systems 3
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Electrical Specifications (continued)
Parameter Device Symbol Min Typ Max Unit
Output Voltage Set Point
(VI = 48 Vdc; IO = IO, min to IO, max; TA = 25 °C) P
M
Y
G
F
A
VO, set
VO, set
VO, set
VO, set
VO, set
VO, set
1.18
1.47
1.76
2.45
3.23
4.9
1.2
1.5
1.8
2.5
3.3
5.0
1.22
1.52
1.84
2.55
3.37
5.1
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Output Voltage
(Over all operating input voltage, resistive load, and
temperature conditions until end of life. See Test
Configurations section.)
P
M
Y
G
F
A
VO
VO
VO
VO
VO
VO
1.16
1.45
1.74
2.42
3.20
4.85
—
—
—
—
—
—
1.24
1.55
1.85
2.57
3.40
5.15
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Output Regulation:
Line (VI = 36 V to 75 V)
Load (IO = IO, min to IO, max)
Temperature (TA = –40 °C to + 85 °C)
All
All
All
—
—
—
—
—
—
—
—
—
±5
±5
1.0
mV
mV
%VO, set
Output Ripple and Noise Voltage
See Test Configurations section
Measured across 10 µF Tantalum, 1 µF ceramic, VI = 48
Vdc, TA = 25 °C, IO = IO,max
RMS
Peak-to-peak All
All —
—12
45 —
75 mVrms
mVp-p
External Load Capacitance All CO 0 — 10,000 µF
Output Current G,Y,M,P
F
A
IO
IO
IO
0
0
0
—
—
—
20.0
15.0
10.0
Adc
Adc
Adc
Output Current-limit Inception
(VO = 90% of VO, set) G,Y,M,P
F
A
IO
IO
IO
—
—
—
23.5
17.5
11.75
—
—
—
Adc
Adc
Adc
Output Short-circuit Current (Average)
(VO = 0.25 V) G,Y,M,P
F
A
IO
IO
IO
—
—
—
13
10
7
—
—
—
Adc
Adc
Adc
Efficiency (VI = 48 Vdc; IO = IO, max),TA = 25 °C P
M
Y
G
F
A
η
η
η
η
η
η
—
—
—
—
—
—
84
86
87
89
91
92
—
—
—
—
—
—
%
%
%
%
%
%
Switching Frequency All fsw — 320 — kHZ
Tyco Electronics Power Systems 4
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Electrical Specifications (continued)
Isolation Specifications
General Specifications
Parameter Device Symbol Min Typ Max Unit
Dynamic Response
(di/dt = 0.1 A/µs, VI = 48 V, TA = 25 °C)
Cout = 220µF Electrolytic and 1µF tantalum.
Load Change from IO = 50% to 75% of IO, max,
Peak Deviation
Settling Time (VO < 10% of peak deviation)
Load Change from IO = 50% to 25% of IO, max,
Peak Deviation
Settling Time (VO < 10% of peak deviation)
All
All
All
All
—
—
—
—
—
—
—
—
200
0.2
200
0.2
—
—
—
—
mV
ms
mV
ms
Parameter Symbol Min Typ Max Unit
Isolation Capacitance Ciso — 1000 — PF
Isolation Resistance Riso 10 — — MΩ
Isolation Voltage Viso — — 1500 Vdc
Parameter Min Typ Max Unit
Calculated MTBF (IO = 80% of IO, max TA = 25 °C)
Tyco RIN (Reliability Infomation Notebook) Method 3,178,000 Hours
Weight — 27.4(0.97) — g (oz.)
Tyco Electronics Power Systems 5
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See
Feature Descriptions for additional information.
Parameter Device Symbol Min Typ Max Unit
Remote On/Off Signal Interface
(VI = VI,min to VI,max; open collector or compatible, signal
referenced to VI(–) terminal)
Negative Logic: Device Code Suffix “1”:
Logic Low—Module On / Logic High—Module Off
Positive Logic: If Device Code Suffix “1” Is Not Specified:
Logic Low—Module Off / Logic High—Module On
Module Specifications:
On/Off Current—Logic Low
On/Off Voltage—Logic Low
On/Off Voltage—Logic High (Ion/off = 0 mA)
Open Collector Switch Specifications:
Leakage Current During Logic High (Von/off = 15 V)
Output Low Voltage During Logic Low (Ion/off = 1 mA)
All
All
All
All
All
Ion/off
Von/off
Von/off
Ion/off
Von/off
—
–0.7
—
—
—
—
—
—
—
—
1.0
1.2
15
50
1.2
mA
V
V
µA
V
Turn-on Delay and Rise Times
(at 80% of IO, max; TA = 25 °C):
Case 1: On/Off Input Is Set for Logic High and then Input
Power Is Applied (delay from point at which VI = VI, min until
VO = 10% of VO, set).
Case 2: Input Power Is Applied for at Least One Second, and
Then the On/Off Input Is Set to Logic High (delay from point at
which Von/off = 0.9 V until VO = 10% of VO, set).
Output Voltage Rise Time (time for VO to rise from 10% of
VO, nom to 90% of VO, set)
All
All
All
Tdelay
Tdelay
Trise
—
—
—
17
3
13
—
—
—
ms
ms
ms
Output voltage overshoot
(IO = 80% of IO,max, VI = 48 Vdc TA = 25 °C) All — — 5 %VO,set
Output Voltage Adjustment (See Feature Descriptions section):
Output Voltage Remote-sense Range P,M,Y
G,F,A — — 0.25
10
V
%VO, set
Output Voltage Set-point Adjustment Range (trim) All 90 — 110 %VO, set
Output Overvoltage Protection (clamp) P
M
Y
G
F
A
VO, ovsd
VO, ovsd
VO, ovsd
VO, ovsd
VO, ovsd
VO, ovsd
2.0
2.3
2.3
2.7
3.6
5.5
—
—
—
—
—
—
2.4
2.7
2.7
3.7
4.5
7.2
V
V
V
V
V
V
Overtemperature Protection (VI = 75 V, IO = IO, max)
See Figure 44 All TQ10 /
TQ560 — 120 — °C
Input Undervoltage Lockout:
Turn-on Threshold
Turn-off Threshold All
All —
33 35
34 36
—V
V
Tyco Electronics Power Systems 6
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Characteristic Curves
The following figures provide typical characteristics curves for the QW020A0P1 (VO = 1.2V) module at room temperature (TA
= 25 °C)
Figure 1. Input Voltage and Current Characteristics.
Figure 2. Converter Efficiency vs. Output Current.
Figure 3. Output Ripple Voltage (IO = IO, max).
Figure 4. Transient Response to Step Decrease in
Load from 50% to 25% of Full Load
(VI = 48 Vdc).
Figure 5. Transient Respon se to Step Increase in
Load from 50% to 75% of Full Load
(VI = 48 Vdc).
Figure 6. Start-up from Remote On/Off (IO = IO, max).
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
30 35 40 45 50 55 60 65 70
INPUT VOLTAGE, VI (V)
INPUT CURRENT, I
I
(A)
IO = 20 A
IO = 10 A
IO = 0 A
70
72
74
76
78
80
82
84
86
0 5 10 15 20
V
I
= 36 V
V
I
= 48 V
V
I
= 75 V
OUTPUT CURRENT, I
O
(
A
)
EFFICIENCY, η (%)
TIME, t
(
1
µ
s/div
)
OUTPUT VOLTAGE,
V
O
(V) (20 mV/div)
TIME, t
(
100
µ
s/div
)
OUTPUT VOLTAGE,
V
O
(V) (200 mV/div)
OUTPUT CURRENT,
I
O
(A) (5 A/div)
TIME, t
(
100
µ
s/div
)
OUTPUT VOLTAGE,
V
O
(V) (200 mV/div)
OUTPUT CURRENT,
I
O
(A) (5 A/div)
TIME, t (1 ms/div)
OUTPUT VOLTAGE,
V
O
(V) (500 mV/div)
REMOTE ON/OFF,
V
ON/OFF
(V) (5 V/div)
Tyco Electronics Power Systems 7
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Characteristic Curves
The following figures provi de typical characteristics curves for the QW020A0M1 (VO = 1.5 V) module at room temperature (TA
= 25 °C)
Figure 7. Input Voltage and Current Characteristics.
Figure 8. Converter Efficiency vs. Output Current.
Figure 9. Output Ripple Voltage (IO = IO, max).
Figure 10. Transient Response to Step Decrease in
Load from 50% to 25% of Fu ll Load
(VI = 48 Vdc).
Figure 1 1. Transient Respon se to S tep In crease in Lo ad
from 50% to 75% of Full Load
(VI = 48 Vdc).
Figure 12. Start-up from Remote On/Off (IO = IO, max).
0
0.2
0.4
0.6
0.8
1
1.2
30 35 40 45 50 55 60 65 70 75
INPUT VOLTAGE, V
I
(V)
INPUT CURRENT, I
I
(A)
I
O
= 20A
I
O
= 10A
I
O
= 0A
70
72
74
76
78
80
82
84
86
88
0 2 4 6 8 101214161820
OUTPUT CURRENT, IO (A)
EFFICIENCY, η (%)
VI = 36V
VI = 48V
VI = 75V
TIME, t
(
1
µ
s/div
)
OUTPUT VOLTAGE,
V
O
(V) (200 V/div)
TIME, t
(
100
µ
s/div
)
OUTPUT VOLTAGE,
V
O
(V) (200 mV/div)
OUTPUT CURRENT,
I
O
(A) (5 A/div)
TIME, t
(
100
µ
s/div
)
OUTPUT VOLTAGE,
V
O
(V) (200 mV/div)
OUTPUT CURRENT,
I
O
(A) (5 A/div)
TIME, t
(
1 ms/div
)
OUTPUT VOLTAGE,
VO (V) (500 mV/div)
REMOTE ON/OFF,
V
ON/OFF
(5 V/div)
Tyco Electronics Power Systems 8
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Characteristic Curves
The following figures provide typical characteristics curves for the QW020A0Y1 (VO = 1.8V) module at room temperature (TA
= 25 °C)
Figure 13. Input Voltage and Current Characteristics.
Figure 14. Converter Efficiency vs. Output Current.
Figure 15. Output Ripple Voltage (IO = IO, max).
Figure 16. Transient Response to Step Decrease in
Load from 50% to 25% of Full Load
(VI = 48 Vdc).
Figure 17. Transient Response to Step Increase in
Load from 50% to 75% of Full Load
(VI = 48 Vdc).
Figure 18. Start-up from Remote On/Off (IO = IO, max).
0
0.2
0.4
0.6
0.8
1
1.2
1.4
30 35 40 45 50 55 60 65 70
INPUT VOLTAGE, V
I
(V)
INPUT CURRENT, I
I
(A)
I
O
= 20 A
I
O
= 10 A
I
O
= 0 A
70
72
74
76
78
80
82
84
86
88
0 5 10 15 20
VI = 36 V
VI = 48 V
VI = 75 V
OUTPUT CURRENT, IO (A)
EFFICIENCY, η (%)
TIME, t (1 µs/div)
OUTPUT VOLTAGE,
V
O
(V) (20 mV/div)
TIME, t
(
100
µ
s/div
)
OUTPUT VOLTAGE,
V
O
(V) (200 mV/div)
OUTPUT CURRENT,
I
O
(A) (5 A/div)
TIME, t
(
100
µ
s/div
)
OUTPUT VOLTAGE,
V
O
(V) (200 mV/div)
OUTPUT CURRENT,
I
O
(A) (5 A/div)
TIME, t (1 ms/div)
OUTPUT VOLTAGE,
V
O
(V) (500 mV/div)
REMOTE ON/OFF,
V
ON/OFF
(V) (5 V/div)
Tyco Electronics Power Systems 9
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Characteristic Curves
The following figures provide typical characteristics curves for the QW020A0G1 (VO = 2.5 V) module at room temperature (T A =
25 °C)
Figure 19. Input Voltage and Current Characteristics.
Figure 20. Converter Efficiency vs. Output Current.
Figure 21. Output Ripple Voltage (IO = IO, max).
Figure 22. Transient Response to Step Decrease in
Load from 50% to 25% of Fu ll Load
(VI = 48 Vdc).
Figure 23. T ran sient R esponse to S tep In crease in Load
from 50% to 75% of Full Load
(VI = 48 Vdc).
Figure 24. Start-up from Remote On/Off (IO = IO, max).
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
30 35 40 45 50 55 60 65 70
INPUT VOLTAGE, V
I
(V)
INPUT CURRENT, I
I
(A)
I
O
= 20 A
I
O
= 10 A
I
O
= 0 A
70
72
74
76
78
80
82
84
86
88
90
0 5 10 15 2
0
OUTPUT CURRENT, IO (A)
EFFICIENCY, η (%)
VI = 75 V
VI = 36 V
VI = 48 V
TIME, t (1 µs/div)
OUTPUT VOLTAGE,
V
O
(V) (20 mV/div)
TIME, t
(
100
µ
s/div
)
OUTPUT VOLTAGE,
VO (V) (100 mV/div)
OUTPUT CURRENT,
I
O
(A) (5 A/div)
TIME, t
(
100
µ
s/div
)
OUTPUT VOLTAGE,
VO (V) (100 mV/div)
OUTPUT CURRENT,
I
O
(A) (5 A/div)
ON/OFF VOLTAGE,
V
ON/OFF
(V) (5 V/div)
OUTPUT VOLTAGE,
V
O
(V) (1 V/div)
TIME, t (5 ms/div)
Tyco Electronics Power Systems 10
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Characteristic Curves
The following figures provide typical characteristics curves for the QW015A0F1(VO = 3.3 V) module at room temperature (TA
= 25 °C)
Figure 25. Input Voltage and Current Characteristics.
Figure 26. Converter Efficiency vs. Output Current.
Figure 27. Output Ripple Voltage (IO = IO, max).
Figure 28. Transient Response to Step Decrease in
Load from 50% to 25% of Full Load
(VI = 48 Vdc).
Figure 29. Transient Response to Step Increase in
Load from 50% to 75% of Full Load
(VI = 48 Vdc).
Figure 30. Start-up from Remote On/Off (IO = IO, max).
30 40 50 60 70
1.8
1.6
1.4
1.2
1
0.8
0.6
0.4
0.2
0
I
O
= 15 A
I
O
= 7.5 A
I
O
= 1 A
INPUT VOLTAGE, V
I
(V)
INPUT CURRENT, I
I
(A)
0123456789101112131415
OUTPUT CURRENT, I
O
(A)
95
90
85
80
75
70
EFFICIENCY, η (%)
V
I
= 36 V
V
I
= 48 V
V
I
= 75 V
TIME,t (2 µs/div)
OUTPUT VOLTAGE,
V
O
(V) (10 mV/div)
TIME, t
(
100
µ
s/div
)
OUTPUT VOLTAGE,
V
O
(V) (200 mV/div)
OUTPUT CURRENT,
I
O
(A) (2 A/div)
TIME, t
(
100
µ
s/div
)
OUTPUT VOLTAGE,
V
O
(V) (200 mV/div)
OUTPUT CURRENT,
I
O
(A) (2 A/div)
TIME, t
(
100
µ
s/div
)
OUTPUT VOLTAGE,
V
O
(V) (200 mV/div)
OUTPUT CURRENT,
I
O
(A) (2 A/div)
Tyco Electronics Power Systems 11
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Characteristic Curves
The following figures provide typical characteristics curves for the QW010A0A1(VO = 5.0 V) module at room temperature (TA =
25 °C)
Figure 31. Input Voltage and Current Characteristics.
Figure 32. Converter Efficiency vs. Output Current.
Figure 33. Output Ripple Voltage (IO = IO, max).
Figure 34. Transient Response to Step Decrease in
Load from 50% to 25% of Fu ll Load
(VI = 48 Vdc).
Figure 35. T ran sient R esponse to S tep In crease in Load
from 50% to 75% of Full Load
(VI = 48 Vdc).
Figure 36. Start-up from Remote On/Off (IO = IO, max).
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
30 35 40 45 50 55 60 65 70 75
INPUT VOLTAGE, V
I
(V)
INPUT CURRENT, I
I
(A)
I
O
= 10A
I
O
= 5A
I
O
= 0A
70
75
80
85
90
95
012345678910
OUTPUT CURRENT, I
O
(
A
)
EFFICIENCY, η (%)
V
I
= 36V
V
I
= 48V
V
I
= 75V
TIME, t
(
1
µ
s/div
)
OUTPUT VOLTAGE,
V
O
(V) (10 mV/div)
TIME, t
(
100
µ
s/div
)
OUTPUT VOLTAGE,
VO (V) (200 mV/div)
OUTPUT CURRENT,
I
O
(A) (2 A/div)
TIME, t
(
100
µ
s/div
)
OUTPUT VOLTAGE,
VO (V) (200 mV/div)
OUTPUT CURRENT,
I
O
(A) (2 A/div)
TIME, t
(
10 ms/div
)
OUTPUT VOLTAGE,
VO (V) (2 V/div)
REMOTE ON/OFF,
V
ON/OFF
(5 V/div)
Tyco Electronics Power Systems 12
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Test Configurations
Note: Measure input reflected ripple current with a simulated source
inductance (LTEST) of 12µH. Capacitor CS offsets possible
battery impedance. Measure current as shown above.
Figure 37. Input Reflected Ripple Current Test Setup.
Note: Scope measurements should be made using a BNC socket,
with a 10 µF tantalum capacitor and a 1 µF ceramic capcitor.
Position the load between 51 mm and 76 mm (2 in and 3 in)
from the module
Figure 38. Peak-to-Peak Output Ripple Measurement
Test Set up.
Note: All voltage measurements to be taken at the module termi-
nals, as shown above. If sockets are used then Kelvin con-
nections are required at the module terminals to avoid
measurement errors due to socket contact resistance.
Figure 39. Output Voltage and Efficiency Test Setup.
Safety Considerations
For safety-agency approval of the system in which the power
module is used, the power module must be installed in com-
pliance with the spacing and separation requirements of the
end-use safety agency standard, i.e., UL60950, CSA C22.2
No. 60950-00, and
VDE 0805:2001-12 (IEC60950, 3rd Ed).
These converters have been evaluated to the spacing
requirements for Basic Insulation, per the above safety stan-
dards.
For Basic Insulation models ("–B" Suffix), 1500 Vdc is
applied from VI to VO to 100% of outgoing production.
For end products connected to –48 Vdc, or –60 Vdc nomianl
DC MAINS (i.e. central office dc battery plant), no further
fault testing is required.
Note:–60 V dc nominal bettery plants are not available in the
U.S. or Canada.
For all input voltages, other than DC MAINS, where the input
voltage is less than 60 Vdc, if the input meets all of the
requirements for SELV, then:
Q
The output may be considered SELV. Output voltages will
remain withing SELV limits even with internally-generated
non-SELV voltages. Single component failure and fault
tests were performed in the power converters.
Q
One pole of the input and one pole of the output are to be
grounded, or both circuits are to be kept floating, to main-
tain the output voltage to ground voltage within ELV or
SELV limits.
For all input sources, other than DC MAINS, where the input
voltage is between 60 and 75 Vdc (Classified as TNV- 2 in
Europe), the following must be adhered to, if the converter’s
output is to be evaluated for SELV:
Q
The input source is to be provided with reinforced insula-
tion from any hazardous voltage, including the AC mains.
Q
One VI pin and one VO pin are to be reliably earthed, or
both the input and output pins are to be kept floati ng.
Q
Another SELV reliability test is conducted on the whole
system, as required by the safety agencies, on the combi-
nation of supply source and the subjec t module to verify
that under a single fault, hazardous voltages do not
appear at the module’s output.
The power module has ELV (extra-low voltage) outputs
when all inputs are ELV.
All flammable materials used in the manufacturing of these
modules are rate d 94V-0, and UL60950A.2 for reduced
thicknesses. The input to these units is to be provided with a
maximum 5A time-delay in the unearthed lead.
TO OSCILLOSCOPE
12 µH
C
S
220 µF
ESR < 0.1 Ω
@ 20 ˚C, 100 kHz
V
I
(+)
V
I
(-)
BATTERY
L
TEST
33 µF
ESR < 0.7 Ω
@ 100 kHz
V
O
(+)
V
O
(–)
10 µF RESISTIVE
LOAD
SCOPE
COPPER STRIP
1 µF
VI(+)
II IO
SUPPLY
CONTACT
RESISTANCE
CONTACT AND
DISTRIBUTION LOSSES
LOAD
SENSE(+)
V
I(-)
VO(+)
VO(-)
SENSE(-)
ηVO(+) VO(-)
–[]IO
×
VI(+) VI(-)
–[]II
×
------------------------------------------------
⎝⎠
⎛⎞
100×=
Tyco Electronics Power Systems 13
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source imped-
ances can affect the st ability of the power module. If the input
source inductance exceeds 4 µH, a 33 µF electrolytic capaci-
tor (ESR < 0.7 W at 100 kHz) mounted close to the power
module helps ensure stability of the unit.
Feature Descriptions
Remote On/Off
Two remote On/Off options are available. Positive logic
remote On/Off turns the module on during a logic-high volt-
age on the remote ON/OFF pin, and off during a logic low.
Negative logic remote On/Off, device code suffix "1", turns
the module off during logic-high voltage and on during a logic
low.
To turn the power module on and off, the user must supply a
switch to contro l th e vo ltage between the
ON/OFF pin and the VI(–) terminal. The switch may be an
open collector or equivale nt (see Figu re 40). A logic low is
Von/off = –0.7 V to 1.2 V. The maximum Ion/off during a logic
low is 1 mA. The switch should maintain a logic-low voltage
while sinking 1 mA. During a logic high, the maximum Von/off
generated by the power module is 15 V. The maximum allow-
able leakage current of the switch at Von/off = 15 V is 50 µA.
If not using the remote on/off feature, do one of the following:
For positive logic, leave the ON/OFF pin open.
For negative logic, short the ON/OFF pin to VI(–).
Figure 40. Remote On/Off Implementation.
Remote Sense
Remote sense minimizes the effects of distribution losses by
regulating the voltage at the remote sense connections. The
voltage between the remote sense pins and the output termi-
nals must not exceed the output voltage sense range given in
the Feature Specifications table:
[VO(+) – VO(–)] – [SENSE(+) – SENSE(–)] £ 0.5 V
The voltage between the VO(+) and VO(–) terminals must not
exceed the minimum output overvoltage protection value
shown in the Feature Specifications table. This limit includes
any increase in voltage due to remote sense compensation
and output voltage set-point adjustment (trim) (See Figure
41). If not using the remote sense feature to regulate the out-
put at the point of load, then connect SENSE(+) to VO(+) and
SENSE
(–) to VO(–) at the module.
Although the output voltage can be increased by both the
remote sense and by the trim, the maximum increase for the
output voltage is not the sum of both. The maximum increase
is the larger of either the remote sense or the trim.
The amount of power delivered by the module is define d as
the voltage at the output terminals multiplied by the output
current. When using remote sense and trim, the output volt-
age of the module can be increased, which at the same out-
put current would increase the power output of the module.
Care should be taken to ensure that the maximum output
power of the module remains at or below the maximum rated
power.
Figure 41. Effective Equivalent Circuit Configuration for
Single-Mod ule Remote-Sen se Operation.
Output Voltage Set-Point Adjustment (Trim)
Output voltage trim allows the user to increase or decrease
the output voltage set point of a module. This is accom-
plished by connecting an external resistor between the TRIM
pin and either the SENSE(+) or SENSE(–) pins. The trim
resistor should be positioned close to the module. If not using
the trim feature, leave the TRIM pin open.
with an external resistor Rtrim-down between the TRIM and
SENSE(–) pins, the output voltage set point VO, set
decreases (see Figure 48). The following equation deter-
mines the required external-resistor value to trim-down the
output voltage:
Rtrim-down is the external resistor in kΩ
∆% is the percentage change in voltage
A and B values are defined in Table 1 for various mode ls.
+
Ion/off
-
Von/off
REMOTE
ON/OFF
VI(+)
VI(-)
VO(+)
SENSE(+)
SENSE(-)
VO(-)
VI(+)
VI(-)
IOLOAD
CONTACT AND
DISTRIBUTION LOSSES
SUPPLY II
CONTACT
RESISTANCE
Rtrim-down A
F
----B–
⎩⎭
⎨⎬
⎧⎫
kΩ=
F∆%
100
---------
=
Tyco Electronics Power Systems 14
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Feature Descriptions (continued)
Output Voltage Set-Point Adjustment (Trim) (con-
tinued)
Table 1
For example, to trim-down the output voltage of 2.5 V mod-
ule (QW020A0G) by 8% to 2.3 V, Rtrim-down is calculated
as follows:
F= 0.08, A = 5.11, & B = 45.31
Figure 42. Circuit Configuration to Decrease Output
Voltage.
The QW010/015/020 modules have a fixed current-limit set
point. As the output voltage is trim-down, the available out-
put power is reduced.
With an external resistor Rtrim-up, connected between the
TRIM and SENSE(+) pins, the output voltage set point VO,
set increases (see Figure 42). The followi ng equation deter-
mines the required external-resistor value to trim-up and out-
put voltage:
Rtrim-up is the external resistor in kW
∆% is the percentage change in voltage
A and B values are defined in Table 2 for various
models
Table 2
For example, to trim-up the output vo ltage of 1.5 V module
(QW020A0M) by 8% to 1.62 V, Rtrim-up is ca lculated as fol-
lows:
F= 0.08, A = 3.946, & B = 11.454
Figure 43. Circuit Configuration to Increase Output
Voltage.
The voltage between the VO(+) and VO(–) terminals must
not exceed the minimum output overvoltage protection value
shown in the Feature S pecifications table. This limit includes
any increase in voltage due to remote-sense compensation
and output voltage set-point adjustment trim.
Although the output voltage can be increased by both the
remote sense and by the trim, the maximum increase for the
output voltage is not the sum of both. The maximum
increase is the larger of either the remote sense or the trim.
The amount of power delivered by the module is defined as
the voltage at the output terminals multiplied by the output
current. When using remote sense and trim, the output volt-
age of the module can be increased, which at the same out-
put current would increase the power output of the module.
Care should be taken to ensure that the maximum output
power of the module rema ins at or below the maxi mum
rated power.
V
O
AB
5.0 5.11 45.31
3.3 5.11 45.31
2.5 5.11 45.31
1.8 3.248 18.645
1.5 2.312 17.711
1.2 2.315 17.711
Rtrim-down 5.11
0.08
---------- 45.31–
⎩⎭
⎨⎬
⎧⎫
kΩ=
Rtrim-down 18.565kΩ=
VI(+)
VI(–)
ON/OFF
VO(+)
VO(–)
SENSE(+)
TRIM
SENSE(–)
Rtrim-down
RLOAD
Rtrim-up A
F
----B–
⎩⎭
⎨⎬
⎧⎫
kΩ=
F∆%
100
---------
=
Output Voltage
(V) ABC
1.2 15.9 1089 62.0
1.5 19.8 1089 104
1.8 23.8 1089 104
2.5 34.5 1690 73.1
3.3 45.5 1690 73.1
5.0 69.0 1690 73.1
Rtrim-up 3.946
0.08
------------- 11.454–
⎩⎭
⎨⎬
⎧⎫
kΩ=
Rtrim-up 37.871kΩ=
VI(+)
VI(–)
ON/OFF
VO(+)
VO(-)
SENSE(+)
TRIM
SENSE(–)
Rtrim-up
RLOA
D
Tyco Electronics Power Systems 15
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Feature Descriptions (continued)
Overcurrent Protection
To provide protection in an output overload fault condition,
the module is equipped with internal current-limiting circuitry,
and can endure current limiting for an unlimited duration. At
the instance of current-limit inception, the module enters a
"hiccup" mode of operation, whereby it shuts down and auto-
matically attempts to restart. While the fault condition exists,
the module will remain in this mode until the fault is cleared.
The unit operates normally once the output current is
reduced back into its specified range.
Output Overvoltage Protection
The output overvoltage protection consists of circuitry that
monitors the voltage of the output terminals. If the output volt-
age exceeds the overvoltage protection threshold, the mod-
ule enters a "hiccup" mode of operation, whereby it shuts
down and automatically attempts to restart. While the fault
condition exists, the module will remain in this hiccup mode
until the overvoltage fault is cleared.
Overtemperatu re Protection
The output overvoltage protection consists of circuitry that
monitors the voltage on the output terminals. If the output
voltag e exce ed s th e overvoltag e p r ot ection threshol d, the
module enters a "hiccup" mode of operation, whereby it shuts
down and automatically attempts to restart. While the fault
condition exists, the module will remain in this hiccup mode
until the overvoltage fault is cleared.
Input Undervoltage Lockout
At input voltages below the input undervoltage lockout limit,
the module operation is disabled. The module will begin to
operate at an input voltage above the undervoltage lockout
turn-on threshold.
Tyco Electronics Power Systems 16
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Thermal Considerations
The power modules operate in a variety of thermal environ-
ments; however, sufficient cooling should be provided to help
ensure reliable operation of the unit. Heat is removed by con-
duction, convection, and radiation to the surrounding environ-
ment. Proper cooling can be verified by measuring drain pin
of Q560 or of Q10 at the positi on indicated in Figure 44.
The temperature at Q560 and Q10 drain pins should not
exceed 110 °C. The output power of the module should not
exceed the rated power for the module
(VO, set x IO, max).
Although the maximum operating ambient temperature of the
power modules is 85 °C, you can limit this temperature to a
lower value for extremely high reliability.
Figure 44. Temperature Measurem ent
Location,QW015A0F (Top View).
Heat Trans fe r via Co nv e ct io n
Increasing airflow over the module enhances the heat trans-
fer via convection. Figures 45—55 show the maximum cur-
rent that can be delivered by various modules versus local
ambient temperature (TA) for natural convection through 2 m/
s (400 ft./min.).
Systems in which these power modules may be used typi-
cally generate natural convection airflow rates of 0.3 ms–1
(60 ft./min.) due to other heat-dissipating components in the
system. Therefore, the natural convection condition repre-
sents airflow rates of up to 0.3 ms–1 (60 ft./min.).
Example
What is the minimum airflow necessary for a QW015A0F1
operating at VIN = 48 V, an output current of 12 A, and a
maximum ambient temperature of 75 °C.
Solution
Given: VIN = 48V
IO = 12 A
TA = 75 °C
Determine airflow (v) (Use Figure 52)
v = 0.5 m/s (100 ft./min.)
Figure 45. Derating Curves for QW010A0A1 (VO = 5.0V)
in Longitudinal Orientation with no heat sink
(VI = 48 Vdc).
Figure 46. Derating Curves for QW010A0F1 (VO = 3.3V)
in Longitudinal Orientation with no heat sink
(VI = 48 Vdc).
Figure 47. Derating Curves for QW010A0G1 (VO = 2.5V)
in Longitudinal Orientation with no heat sink
(VI = 48 Vdc).
AIRFLOW
Q560
Q10
10
8
6
4
2
0
OUTPUT CURRENT, IO (A)
25 35 45 55 65 75 85
LOCAL AMBIENT TEMPERATURE, TA
(
˚C
)
2.0 m/s (400 ft./min.)
1.0 m/s (200 ft./min.)
0.5 m/s (100 ft./min.)
NATURAL CONVECTION
0
2
4
6
8
10
12
14
16
20 30 40 50 60 70 80 90
Local Ambient Temperature T
A
(˚C)
Output Current I
O
(A)
2.0 m/s (400 ft./min.)
1.0 m/s (200 ft./min.)
0.5 m/s (100 ft./min.)
NATURAL CONVECTION
0
5
10
15
20
25 30 35 40 45 50 55 60 65 70 75 80 85
LOCAL AMBIENT TEMPERATURE, TA
(
˚C
)
OUTPUT CURRENT, I
O
(A)
2.0 m/s (400 ft./min.)
1.0 m/s (200 ft./min.)
0.5 m/s (100 ft./min.)
NATURAL CONVECTION
Tyco Electronics Power Systems 17
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Thermal Considerations (continued)
Figure 48. Derating Curves for QW010A0Y1 (VO = 1.8V)
in Longitudin a l Orient a tion with no heat sink
(VI = 48 Vdc).
Figure 49. Derating Curves for QW010A0P1 (VO = 1.2V)
in Longitudin a l Orient a tion with no heat sink
(VI = 48 Vdc).
Layout Considerations
Copper paths must not be routed beneath the power module.
For additional layout guidelines, refer to the FLTR100V10 or
FLTR100V20 data sheet.
0
5
10
15
20
25 30 35 40 45 50 55 60 65 70 75 80 8
5
LOCAL AMBIENT TEMPERATURE, T
A
(
˚C
)
OUTPUT CURRENT, I
O
(A)
2.0 m/s (400 ft./min.)
1.0 m/s (200 ft./min.)
0.5 m/s (100 ft./min.)
NATURAL CONVECTION
0
5
10
15
25 30 35 40 45 50 55 60 65 70 75 80 8
5
20
LOCAL AMBIENT TEMPERATURE, TA (˚C)
OUTPUT CURRENT, IO (A)
2.0 m/s (400 ft./min.)
1.0 m/s (200 ft./min.)
0.5 m/s (100 ft./min.)
NATURAL CONVECTION
Tyco Electronics Power Systems 18
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Through-Hole Lead-Free Soldering Infor-
mation
The RoHS-compliant through-hole products use the SAC
(Sn/Ag/Cu) Pb-free solder and RoHS-compliant components.
They are designed to be processed through sin gle or dual
wave soldering machines. The pins have an RoHS-compli-
ant finish that is compatible with both Pb and Pb-free wave
soldering processes. A maximum preheat rate of 3°C/s is
suggested. The wave preheat process sh ould be such that
the temperature of the power module board is kept below
210°C. For Pb solder, the recommended pot temperature is
260°C, while the Pb-free solder pot is 270°C max. Not all
RoHS-compliant through-hole pr oducts can be processed
with paste-through-hole Pb or Pb-free reflow process. If addi-
tional information is needed, please consult with your Tyco
Electronics Power System representative for more details.
Surface Mount Information
Pick and Place Area
Although the module weigh t is minimized by using open-
frame construction, the modules have a relatively large mass
compared to conventional surface-mount components. To
optimize the pick-and-place process, automated vacuum
equipment variables such as nozzle size, tip style, vacuum
pressure, and placement speed should be considered. Sur-
face-mount versions of this family have a flat surface which
serves as a pick-and-place location fo r automated vacuum
equipment. The module’s pick-and-place location is identified
in Figure 56.
Figure 50. Pick and Place Location.
Reflow Soldering Information
The QW series of power modules is available for eith er
Through-Hole (TH) or Surface Mount (SMT) soldering.
These power modules are large mass, low thermal resistance
devices and typically heat up slower than other SMT compo-
nents. It is recommended that the customer review data
sheets in order to customize the solder reflow profile for each
application boa rd assembly.
The following instructions must be observed when SMT sol-
dering these units. Failure to observe these instructions may
result in the failure of or cause damage to the modules, and
can adversely affect long-term reliability.
Typically, the eutectic solder melts at 183oC, wets the land,
and subsequently wicks the device connection. Sufficient
time must be allowed to fuse the plating on the connection to
ensure a reliable solder joint. There are severa l types of
SMT reflow technologies currently used in the industry.
These surface mount power modules can be reliably sol-
dered using natural forced convection, IR (radian t infrared),
or a combination of convection/IR.
Figure 51. Recommen de d Re fl ow profile.
Figure 52. Time Limit curve above 2050C.
Lead Free Soldering
The -Z version SMT modules of the QW series are lead-free
(Pb-free) and RoHS compliant and are compatible in a Pb-
free soldering process. Failure to observe the instructions
below may result in the failure of or cause damage to the
modules and can adversely affect long-term reliability.
Pb-free Reflow Profile
Power Systems will comply with J-STD-020 Rev. C (Moisture/
Reflow Sensitivity Classification for Nonhermetic Solid State
Surface Mount Devices) for both Pb-free solder profiles and
MSL classification procedures. This standard provides a rec-
ommended forced-air-convection reflow profile based on the
volume and thickness of the package (table 4-2). The sug-
gested Pb-free solder paste is Sn/Ag/Cu (SAC). The recom-
mended linear reflow profile using Sn/Ag/Cu solder is shown
in Figure. 59.
Pick and Place Target
Symbol on Label
Product Label
PIN 1 PIN 2 PIN 3
PIN 8 PIN 7 PIN 6 PIN 5 PIN 4
25.654
(1.01)
18.288
(0.72)
0
50
100
150
200
250
300
REFL OW TIM E (S)
Preheat zone
max 4
o
Cs
-1
Soak zone
30-240s
Heat zone
max 4
o
Cs
-1
Peak Tem p 235
o
C
Cooling
zone
1-4
o
Cs
-1
T
lim
above
205
o
C
200
205
210
215
220
225
230
235
240
010 20
30
40
50 60
TIME (S)
Tyco Electronics Power Systems 19
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Surface Mount Information (continued)
Storage and Handling
The recommended storage environment and handling proce-
dures for moisture-sensitive surface mount packages is
detailed in J-STD-033 Rev. A (Handling, Packing, Shipping
and Use of Moisture/Reflow Sensitive Surface Mount
Devices). Moisture barrier bags (MBB) with desiccant are
required for MSL ratings of 2 or greater. These sealed pack-
ages should not be broken until time of use. Once the origi-
nal package is broken, the floor life of the product at
conditions of £ 30°C and 60% relative humidity varies
according to the MSL rating (see J-STD-033A). The shelf life
for dry packed SMT packages will be a minimum of 12
months from the bag seal date, when stored at the following
conditions: < 40° C, < 90% relative humidity.
Post Solder Cleaning and Drying Considerations
Post solder cleaning is usually the final circuit-board
assembly process prior to electrical board testing. The result
of inadequate cleaning and drying can affect both the
reliability of a power module and the testability of the finished
circuit-board assembly. For guidance on appropriate
soldering, cleaning and drying proce dures, refer to Tyco
Electronics Board Mounted Power Modules: Sold ering and
Cleaning Application Note (AP01-056EPS).
Figure 53. Recommended linear reflow profile using Sn/
Ag/Cu solder.
Solder Ball and Cleanliness Requirements
The open frame (no case or potting) power module will meet
the solder ball requirements per J-STD-001B. These require-
ments state that solder balls must neither be loose nor violate
the power module minimum electrical spacing.
The cleanliness designator of the open frame power module
is C00 (per J specification).
Per J-STD-020 Rev. C
0
50
100
150
200
250
300
Reflow Time (Seconds)
Reflow Temp (°C)
Heating Zone
1°C/Second
Peak Temp 260°C
* Min. Time Above 235°C
15 Seconds
*Time Above 217°C
60 Seconds
Cooling
Zone
Tyco Electronics Power Systems 20
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Outline Diagram for Surface-Mount Module
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in. ± 0.010 in.)
SIDE VIEW
TOP VIEW
BOTTOM VIEW
V
IN
(+)
ON/OFF
V
IN
(-)
V
OUT
(+)
+SENSE
TRIM
-SENSE
V
OUT
(-)
57.9
(2.28)
36.8
(1.45)
LABEL LOCATION AND
ORIENTATION (CONTENTS
WILL VARY)
3.3
(.130)
min stand-off
height
0.5
(.020)
max compliance
8.5
(.335)
MAX
ø
1.00
(.040)
6 Places
ø
1.50
(.060)
2 Places
3.6
(0.14)
50.8
(2.00)
7.62
(.300)
3.81
(.150)
11.43
(.450)
15.24
(.600)
10.8
(0.43)
15.24
(0.600)
7.62
(0.300)
Tyco Electronics Power Systems 21
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Outline Diagram for Through-Hole Module
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in. ± 0.010 in.)
8.5
(.335)
Max
SIDE VIEW
TOP VIEW
BOTTOM VIEW
4.5
(0.18)
MIN
ø
1.00
(.040)
6 Places
ø
1.50
(.060)
2 Places
V
IN
(+)
ON/OFF
V
IN
(-)
V
OUT
(+)
+SENSE
TRIM
-SENSE
V
OUT
(-)
57.9
(2.28)
36.8
(1.45)
LABEL LOCATION AND
ORIENTATION (CONTENTS
WILL VARY)
3.6
(0.14)
50.8
(2.00)
7.62
(.300)
3.81
(.150)
11.43
(.450)
15.24
(.600)
10.8
(0.43)
15.24
(0.600)
7.62
(0.300)
Tyco Electronics Power Systems 22
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Recommended Pad Layout for Surface-Mount Module
and Recommended Hole Layout for Through-Hole Module
Component-side footprint.
Dimensions are in millimeters and (inches), unl ess oth erwise noted.
0.022" DIA VIA
0.032" DIA SOLDER MASK OPENING
4 PLACES FOR OUTPUT PINS
2 PLACES FOR INPUT PINS
0.025" SPACING VIA TO PAD
0.015" MIN SOLDER MASK WALL
0.105" PASTE MASK OPENING
0.110" SOLDER MASK OPENING
NOTES:
1. FOR CGA SURFACE MOUNT PIN
USE THE FOLLOWING PAD
8.89
(0.350)
5.08 (0.200)
3.18 (0.125)
57.9
(2.28)
36.8
(1.45)
10.8
(0.43)
V
I
(+)
ON/OFF
V
I
(–)
50.8
(2.00)
ROUTING KEEP OUT AREA
7.62
(.300)
3.81
(.150)
11.43
(.450) 15.24
(.600)
V
OUT
(+)
+SENSE
TRIM
-SENSE
V
OUT
(-)
16.71
(0.658)
26.75
(1.053)
39.24
(1.545)
49.28
(1.940)
Tyco Electronics Power Systems 23
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Ordering Information
Please contact your Tyco Electronics’ Sales Representative for pricing, availability and optional features.
Table 1. Device Codes
Input Voltage Output
Voltage Output
Current Efficiency Connector Type Device Code Comcodes
36 – 75 Vdc 1.2 V 20 A 85% Through-hole QW020A0P1 10 8968447
36 – 75 Vdc 1.5 V 20 A 87% Through-hole QW020A0M 108976036
36 – 75 Vdc 1.5 V 20 A 87% Through-hole QW020A0M1 108970708
36 – 75 Vdc 1.8 V 20 A 89% Through-hole QW020A0Y1 10 8967522
36 – 75 Vdc 2.5 V 20 A 90% Through-hole QW020A0G 108974783
36 – 75 Vdc 2.5 V 20 A 90% Through-hole QW020A0G1 108969296
36 – 75 Vdc 3.3 V 15 A 91% Through-hole QW015A0F 108971797
36 – 75 Vdc 3.3 V 15 A 91% Through-hole QW015A0F1 108966508
36 – 75 Vdc 5.0 V 10 A 92% Through-hole QW010A0A 108981226
36 – 75 Vdc 5.0 V 10 A 92% Through-hole QW010A0A1 10 8969585
36 – 75 Vdc 1.2 V 20 A 85% SMT QW020A0P-S 108968488
36 – 75 Vdc 1.2 V 20 A 85% SMT QW020A0P1-S 108971961
36 – 75 Vdc 1.2 V 20 A 85% Through-hole QW020A0P1Z CC109107281
36 – 75 Vdc 1.5 V 20 A 87% Through-hole QW0 20A0M1Z CC109107273
36 – 75 Vdc 1.8 V 20 A 89% Through-hole QW020A0Y1Z CC109102968
36 – 75 Vdc 2.5 V 20 A 90% Through-hole QW020A0G1Z CC109101490
36 – 75 Vdc 2.5 V 20 A 90% Through-hole QW020A0GZ CC109107265
36 – 75 Vdc 3.3 V 15 A 91% Through-hole QW015A0FZ CC109103280
36 – 75 Vdc 3.3 V 15 A 91% Through-hole QW015A0F1Z CC109107240
36 – 75 Vdc 5.0 V 10 A 92% Through-hole QW010A0A1Z CC109107232
36 – 75 Vdc 3.3 V 15 A 91% SMT QW015A0F1-SZ 109100427
36 – 75 Vdc 5.0 V 10 A 92% SMT QW010A0A1-SZ 109100410
World Wide Headquarters
Tyco Electronics Power Systems, Inc.
3000 Skyline Drive, Mesquite, TX 75149, USA
+1-800-526-7819 FAX: +1-888-315-5182
(Outside U.S.A.: +1-972-284-2626, FAX: +1-972-284-2900)
www.power.tycoelectronics.com
e-mail: techsupport1@tycoelectronics.com
Tyco Electronics Corporation reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or application.
No rights under any patent accompany the sale of any such product(s) or information.
© 2001 Tyco Electronics Power Systems, Inc. (Mesquite, Texas) All International Rights Reserved.
Printed in U.S.A.
Document Name: DS06-008 ver.1.3
PDF Name: QW010-015-020_ds.pdf
Europe, Middle-East and Africa Headquarters
Tyco Electronics (UK) Ltd
Tel: +44 (0) 1344 469 300, Fax: +44 (0) 1344 469 301
Central America-Latin America Headquarters
Tyco Electronics Power Systems
Tel: +54 11 4316 2866, Fax: +54 11 4312 9508
Asia-Pacific Headquarters
Tyco Electronics Singapore Pte Ltd
Tel: +65 482 0311, Fax: 65 480 9299
Data Sheet
April 5, 2006 36 Vdc to 75 Vdc Input; 1.2 Vdc to 5.0 Vdc Output; 10 A to 20 A
QW010/015/020 Series Power Modules: dc-dc Converters;
Ordering Information (continued)
Optional features can be ordered using the suffixes shown below . The suffixes follow the last letter of the Product Code and are
placed in descending alphanumerical order.
Table 2. Device Options
Option Suffix
Negative remote on/off logic 1
Approved for Basic Insulation –B
Surface mount interconnections –S
Baseplate version for Heatsink attachment
(Through-hole version only) –H
RoHS Compliant -Z
