WaveLink
Differential Probe
System
(4 GHz–6 GHz)
Key Features
4 GHz or 6 GHz models
Up to 5 Vpk-pk dynamic range with
low noise
±3 V offset range
Ideal for DDR2, LPDDR2, DDR3
Innovative QuickLink architecture
Wide variety of tips and leads
• Solder-In Lead
• QuickLink Solder-In Lead
• Positioner (Browser) Tip
• Adjustable (Browser) Tip
• Quick Connect Lead
• Square Pin Lead
• Hi-Temp Solder-In Lead
Low loading and high impedance for
minimal signal disturbance
Deluxe soft carrying case
General Purpose Probe with
Range of Capabilities
Teledyne LeCroy’s WaveLink 4-6 GHz
Differential Probes are a general
purpose probing solution with high-
input dynamic range and offset range
capability. The range of capabilities is
ideal for a variety of high-speed DDR
signals where high dynamic range and
large offset requirements are common.
Wide Variety of Tip and Leads
The wide variety of tips offered with
the D4x0/D6x0 provides condence
that the most challenging test points
can be probed. With seven different
tips available, the D4x0/D6x0 provides
great flexibility when probing, while
maintaining signal integrity. An
assortment of hands-free probe holders
eases the challenge of connecting
multiple leads to a board.
Exceptional Waveform Fidelity
WaveLink probes provide superior
loading characteristics and are
calibrated with a custom “ne-
tuned” frequency response. The
ultra-low loading coupled with a flat
frequency response ensure accurate
measurements.
Unique QuickLink Architecture
The unique QuickLink architecture
allows for probe tips to be quickly
attached or removed to a WaveLink
differential amplier. Unlike other
“consumable” probe tip solutions which
rely on tiny, delicate tips located very
close to the Device Under Test (DUT),
the QuickLink Solder-In tip has an
integral 9-inch lead. QuickLink Solder-
In tips are low cost, making it easy to
equip multiple test points and DUTs and
eliminating time-consuming resoldering
of connectors.
The WaveLink Differential Probe Series is a 4-6 GHz bandwidth active
differential probe series with the widest range of tips, large offset
capability, and high dynamic range.
2
EXCEPTIONAL WAVEFORM FIDELITY
The D4x0/D6x0 probe series has superior electrical
characteristics, providing excellent signal delity. These
probes were designed with low loading and high impedance
for minimal signal disturbance and circuit loading. WaveLink
probes use a unique calibration process where each probe
is programmed with a custom “ne-tuned” frequency
response which is read by the oscilloscope in order to
digitally compensate for the entire system response.
In addition to their electrical performance, WaveLink probes
have the best-in-class mechanical design for optimum
utility. The D4x0/D6x0 probes series includes seven
different interconnect congurations allowing for flexibility
when making measurements. Additionally, WaveLink probes
offer a variety of hands free positioners to offer stable and
accurate probe tip placement to make perfect contact
without the worry of hand probing errors.
3
INNOVATIVE QUICKLINK ARCHITECTURE
High Signal Fidelity
When connected to a WaveLink analog
probe, QuickLink tips provide 8 GHz of
bandwidth and a flat, well-controlled
frequency response. When used for
digital acquisitions with the HDA125,
they support 3 GHz bandwidth with
industry-leading sensitivity. In both
cases, high input impedance ensures
minimal loading of the system
under test.
Easy to connect
Unlike other “consumable” probe tip
solutions which rely on tiny, delicate
tips located very close to the device
under test, the QuickLink solder-in
tip has an integral 9-inch lead. This
effectively relocates your test point to
a more convenient location, making
testing more reliable by eliminating
torque and other forces on the
solder joints.
Cost-effective
QuickLink solder-in tips are low-cost,
making it easy to equip multiple test
points and DUTs, and eliminating time-
consuming re-soldering of connectors.
The QuickLink probe tip system was designed from the ground up to be compatible with both the HDA125 High-speed
Digital Analyzer system, and with Teledyne LeCroy’s WaveLink series of differential analog probes. This cross-connection
ability allows you to equip your system under test with QuickLink tips at all desired test points, and swap connections
between digital and analog acquisition systems as needed.
Dxx30
Differential
Amplifier
Dxx30-QL
Adapter
QL-SI
Solder-In Lead
WaveMaster/SDA/DDA 8 Zi
HDA125
HDA-DLS-18QL
HDA-DLS-9QL
USB
LBUS
Dx10-A
Differential
Amplifier
Dx10-QL
Adapter
Dx20-A
Differential
Amplifier
Dx20-QL
Adapter
4
WIDE VARIETY OF TIPS AND LEADS
Solder-In Lead (SI)
The Solder-In interconnect lead features the
smallest physical tip size of any high band-
width differential probe and the highest
level of electrical performance. Two very
small damping resistors are directly sol-
dered into the connect points for the high-
est impedance and lowest tip inductance.
The resistors have highly flexible leads
allowing connection to input points with a
wide range of input spacing.
Positioner Tip (PT)
The PT positioner tips provides spring
loaded leads to allow for easy probing. The
adjustable wheel allows for precise probing,
allowing a spread up to 0.14”. The small
form factor provides a convenient grip for
hand probing, or use the wand or XYZ posi-
tioner for more precise placement.
Square Pin (SP)
Many applications, such as IC characteriza-
tion boards, use standard 0.025” square
pins for interconnect. The Square Pin in-
terconnect lead directly mates with a pair
of 0.025” (0.635 mm) square pins that are
mounted on standard 0.100” (2.54 mm)
centers.
Offering seven different tips and leads, the D4x0/D6x0 probe series provides condence that the most challenging test
points can be probed. In addition to the various tips, an assortment of hands-free probe holders are provided to ease the
challenge of connecting multiple leads to a board.
High Temperature (HiTemp)
Cables and Solder-In Lead
The 90 cm HiTemp cables and Solder-In
lead can be used for controlled situations
where the differential amplier module
needs to be removed from the extreme
temperature environment. Ideally suited for
testing scenarios where the temperature
can fluctuate from -40 °C to +105 °C.
Quick Connect (QC)
The Quick Connect interconnect lead
enables the probe to be quickly moved
between multiple test points on the test cir-
cuit. Just solder a pair of leaded damping
resistors at each location where intercon-
nection is required. A small connector
mounted on the probe tip plugs into the
damping resistors, enabling a quick con-
nection between sets of test points.
QuickLink Solder-In Lead (QL-SI)
The unique QuickLink architecture allows
for probe tips to be quickly attached
or removed to a WaveLink differential
amplier. The ultra low loading design
allows for unused tips to remain attached
to the DUT without impacting the signal
delity.
5
WaveLink adjustable tip probes are designed to provide an optimum mechanical
connection for signal measurement.
• Built-in thumbwheel for precise positioning of tip — stays put after adjustment
• Maintains sharp points for good contact
• Tips made of “NiTiNOL,” a super-elastic nickel-titanium alloy
• Flexes as you apply pressure
• Consistently returns to original form
WaveLink Differential Amplier Modules
with Adjustable Tip (-AT)
Deluxe Soft Carrying Case
The D4x0/D6x0 probe series includes a deluxe soft carrying case which stores all components of the complete probe
system in one convenient location. The case includes a custom foam insert to securely house the platform/cable assembly
and the differential probe amplier. Additionally, a removable protective storage tray has been designed to neatly arrange
the complete selection of tips/accessories for ease of accessibility. The deluxe soft carrying case can easily t in a
standard-sized le drawer or shelf for storage and is provided as part of the stadard probe conguration.
6
COMPATIBILITY AND STANDARD ACCESSORIES
Compatibility Chart
Platform/Cable
Assembly
Differential
Ampliers
Tips/Leads
Accessories and
Replacement Parts D4x0-A
D6x0-A
Dx10-PT-KIT
Dx20-PT-KIT
WL-PBUS2
WL-PLINK-CASE
D4x0-A-Pxx
D6x0-A-Pxx
Dx10-QL-3SI
Dx20-QL-3SI
Dx10-HiTemp
Dx20-HiTemp Dx00A-AT-Pxx Replacement Part
Amplier System
(includes items below with*)
1 each 1 each D410-A, D420-A, D610-A or D620-A
*Amplier 1 each 1 each
*Solder-In Lead Set
(includes items below with**) 1 each 1 each Dx10-SI, Dx20-SI
**Spare Damping Resistors for SI Tip 1 set of 5 1 set of 5 PKxx0-SI (1 set of 20)
**Tip Retaining Clip for SI & QC Leads 1 each 1 each PK600ST-3
**Adhesive Tape 1 set 1 set Dxx0-PT-TAPE
*Quick Connect Lead Set 1 each 1 each Dx10-QC, Dx20-QC
*Damping Resistors for QC Tip
(Included with QC Tip)
2 sets of
10 2 sets of 10 PKxx0-QC
*Ground Lead 1 each 1 each PACC-LD005
*Ground Clip 1 each 1 each PK006-4
*Square Pin Lead Set 1 each 1 each Dx10-SP, Dx20-SP
*Instruction Manual 1 each 1 each 1 each WL6G-OM-E
*Accessory Info Sheet & Quick Start Guide 1 each 1 each 921489-00 (Dx10), 921488-00(Dx20)
Positioner Tip with Accessories
(kit includes items below with†)
1 each RK-Dx10-PT-KIT, RK-Dx20-PT-KIT
†Positioner Tip Browser 1 each Dx10-PT, Dx20-PT
†Replacement Pogo-pins for Dx10-PT/Dx20-PT 1 set Dxx0-PT-TIPS
†Positioner Tip Probe Guides 1 set Dxx0-PT-GUIDES
†XYZ Positioner 1 each Dxx0-PT-XYZ-POSITIONER
†Adhesive Tape for XYZ Positioner 1 each Dxx0-PT-TAPE
†Browser Wand for PT Tip 1 each Dxx0-PT-WAND
†Interlock Pieces for PT Tip 1 each Dxx0-PT-INTERLOCK
†Swivel for PT Tip 1 each Dxx0-PT-SWIVEL
Platform/Cable Assembly Kit
(includes items below with‡)
1 each 1 each 1 each WL-PLINK-CASE or WL-PBUS2
‡Platform/Cable Assembly 1 each 1 each 1 each
‡Freehand Probe Holder 1 each 1 each 1 each PACC-MS001
‡Probe Deskew Fixture 1 each 1 each 1 each PCF200
‡Platform/Cable Assembly Mounting Clip 1 each 1 each 1 each PK600ST-4 includes clips and clamps
‡Probe Cable Clamp 2 each 2 each 1 each PK600ST-4 includes clips and clamps
‡Deluxe Soft Carrying Case 1 each 1 each 1 each SAC-03
‡Foam Insert for Deluxe Case 1 each* 1 each 1 each 921081-00 (WL-PLINK-CASE) or
921079-00 (WL-PBUS-CASE)
‡Protective Storage Case 1 each 1 each* 1 each 1 each 921083-00
‡Plastic Tray for Storage Case 1 each 1 each* 1 each 1 each 921078-00
QuickLink Adapter 1 each Dx10-QL, Dx20-QL
QuickLink Solder-In Lead 3 each QL-SI-1Pack
HiTemp Solder-In Lead 1 each Dx10-SI-HiTemp, Dx20-SI-HiTemp
HiTemp Cable 1 matched
set
Dx10-Cable-HiTemp,
Dx20-Cable-HiTemp
Calibration Certicate See Ordering Information
Recommended Accessories
Deskew Test Fixture TF-DSQ
Cascade Microtech EZ-Probe Positioner EZ PROBE
* Not Included in WL-PBUS2
SPECIFICATIONS
D610-A-PB2,
D610-A-PL D620-A-PB2,
D620-A-PL D410-A-PB2 D420-A-PB2 D600A-AT-PB2,
D600A-AT-PL D400A-AT-PB2
Bandwidth*
(Probe only, guaranteed)
(System bandwidth, typical)
Dx10-SI, Dx10-QL-SI
and Dx10-PT Tips
6 GHz
Dx10-HiTemp
5 GHz
Dx10-QC Tip
4 GHz
Dx10-SP Tip
3 GHz
Dx20-SI, Dx20-QL-SI
and Dx20-PT Tips
6 GHz
Dx20-HiTemp
5 GHz
Dx20-QC Tip
4 GHz
Dx20-SP Tip
3 GHz
Dx10-SI, Dx10-QL-SI,
Dx10-HiTemp, Dx10-QC
and Dx10-PT Tips
4 GHz
Dx10-SP Tip
3 GHz
Dx20-SI, Dx20-QL-SI,
Dx20-HiTemp, Dx20-QC
and Dx20-PT Tips
4 GHz
Dx20-SP Tip
3 GHz
6 GHz 4 GHz
Rise Time* (10–90%) Dx10-SI, Dx10-QL-SI
and Dx10-PT Tips
75 ps (typical)
Dx10-HiTemp
90 ps (typical)
Dx10-QC Tip
122.5 ps (typical)
Dx10-SP Tip
150 ps (typical)
Dx20-SI, Dx20-QL-SI
and Dx20-PT Tips
75 ps (typical)
Dx20-HiTemp
90 ps (typical)
Dx20-QC Tip
122.5 ps (typical)
Dx20-SP Tip
150 ps (typical)
Dx10-SI, Dx10-QL-SI,
Dx10-HiTemp, Dx10-QC
and Dx10-PT Tips
112 ps (typical)
Dx10-QC Tip
122.5 ps (typical)
Dx10-SP Tip
150 ps (typical)
Dx20-SI, Dx20-QL-SI,
Dx20-HiTemp, Dx20-QC
and Dx20-PT Tips
112 ps (typical)
Dx20-QC Tip
122.5 ps (typical)
Dx20-SP Tip
150 ps (typical)
<75 ps (typical) <112 ps (typical)
Rise Time* (20–80%) Dx10-SI, Dx10-QL-SI
and Dx10-PT Tips
56 ps (typical)
Dx10-HiTemp
67.5 ps (typical)
Dx10-QC Tip
92 ps (typical)
Dx10-SP Tip
113 ps (typical)
Dx20-SI, Dx20-QL-SI
and Dx20-PT Tips
56 ps (typical)
Dx20-HiTemp
67.5 ps (typical)
Dx20-QC Tip
92 ps (typical)
Dx20-SP Tip
113 ps (typical)
Dx10-SI, Dx10-QL-SI,
Dx10-HiTemp, Dx10-QC
and Dx10-PT Tips
84 ps (typical)
Dx10-QC Tip
92 ps (typical)
Dx10-SP Tip
113 ps (typical)
Dx20-SI, Dx20-QL-SI,
Dx20-HiTemp, Dx20-QC
and Dx20-PT Tips
84 ps (typical)
Dx20-QC Tip
92 ps (typical)
Dx20-SP Tip
113 ps (typical)
56 ps (typical) 84 ps (typical)
Noise (System) <36 nV/√Hz
(2.8 mVrms) (typical)
Referred to input,
6 GHz bandwidth
<61 nV/√Hz
(4.8 mVrms) (typical)
Referred to input,
6 GHz bandwidth
<36 nV/√Hz
(2.3 mVrms) (typical)
Referred to input,
4 GHz bandwidth
<67 nV/√Hz
(4.3 mVrms) (typical)
Referred to input,
4 GHz bandwidth
<74 nV/√Hz
(5.8 mVrms) (typical)
Referred to input,
6 GHz bandwidth
<74 nV/√Hz
(4.7 mVrms) (typical)
Referred to input,
4 GHz bandwidth
Input
Input Dynamic Range
(Nominal) 2.5Vpk-pk, ±1.25V 5Vpk-pk, ±2.5V 2.5Vpk-pk, ±1.25V 5Vpk-pk, ±2.5V 4.8Vpk-pk, ±2.4V
Input Common Mode Voltage
Range (Nominal) ±4 V ±2.4 Vmax
Input Offset Voltage Range ±3 V Differential (nominal) n/a
Non-destructive
Input Range (Nominal) ±20 V ±18 V
Attenuation 1.7X / 1.0X (nominal) 3.2X / 1.9X (nominal) 1.7X / 1.0X (nominal) 3.2X / 1.9X (nominal) 2.5X
DC Input Resistance
(Nominal)
200 kΩ Differential
50 kΩ Common Mode
4 kΩ Differential
1 kΩ Common Mode
Impedance
(Zmin, typical)
Dx10-SI, Dx10-QL-SI,
and Dx10-HiTemp
>175 Ω Differential†
Dx10-PT Tip
>175 Ω Differential†
Dx10-QC Tip
>125 Ω Differential†
Dx10-SP Tip
>40 Ω Differential†
Dx20-SI, Dx20-QL-SI,
and Dx20-HiTemp
>250 Ω Differential†
Dx20-PT Tip
>175 Ω Differential†
Dx20-QC Tip
>125 Ω Differential†
Dx20-SP Tip
>40 Ω Differential†
Dx10-SI, Dx10-QL-SI,
and Dx10-HiTemp
>200 Ω Differential†
Dx10-PT Tip
>175 Ω Differential†
Dx10-QC Tip
>100 Ω Differential†
Dx10-SP Tip
>40 Ω Differential†
Dx20-SI, Dx20-QL-SI,
and Dx20-HiTemp
>350 Ω Differential†
Dx20-PT Tip
>175 Ω Differential†
Dx20-QC Tip
>100 Ω Differential†
Dx20-SP Tip
>40 Ω Differential†
>200 Ω Differential >450 Ω Differential
through entire
frequency range
Impedance
(Mid-band, typical)
Dx10-SI, Dx10-QL-SI,
and Dx10-HiTemp
275 Ω at 3 GHz,
175 Ω at 6 GHz
Dx10-PT Tip
200 Ω at 3 GHz,
200 Ω at 6 GHz
Dx10-QC Tip
125 Ω at 3 GHz,
125 Ω at 6 GHz
Dx10-SP Tip
40 Ω at 3 GHz,
100 Ω at 6 GHz
Dx20-SI, Dx20-QL-SI,
and Dx20-HiTemp
475 Ω at 3 GHz,
250 Ω at 6 GHz
Dx20-PT Tip
200 Ω at 3 GHz,
200 Ω at 6 GHz
Dx20-QC Tip
125 Ω at 3 GHz,
200 Ω at 6 GHz
Dx20-SP Tip
40 Ω at 3 GHz,
175 Ω at 6 GHz
Dx10-SI, Dx10-QL-SI,
and Dx10-HiTemp
400 Ω at 2 GHz,
200 Ω at 4 GHz
Dx10-PT Tip
275 Ω at 2 GHz,
175 Ω at 4 GHz
Dx10-QC Tip
150 Ω at 2 GHz,
125 Ω at 4 GHz
Dx10-SP Tip
75 Ω at 2 GHz,
15 Ω at 4 GHz
Dx20-SI, Dx20-QL-SI,
and Dx20-HiTemp
700 Ω at 2 GHz,
350 Ω at 4 GHz
Dx20-PT Tip
275 Ω at 2 GHz,
175 Ω at 4 GHz
Dx20-QC Tip
150 Ω at 2 GHz,
150 Ω at 4 GHz
Dx20-SP Tip
75 Ω at 2 GHz,
15 Ω at 4 GHz
650 Ω at 3 GHz,
200 Ω at 6 GHz
(Differential)
1000 Ω at 2 GHz,
450 Ω at 4 GHz
(Differential)
CMRR (Typical) 30 dB DC to 10 MHz
26 dB 10 MHz to 6 GHz 30 dB DC to 10 MHz
26 dB 10 MHz to 4 GHz >40 dB DC to 1 GHz
>30 dB 1 GHz to
3 GHz
>20 dB to 6 GHz
>40 dB DC to 1 GHz
>30 dB 1 GHz to
3 GHz
>20 dB 3 GHz to
4 GHz
Environmental
Temperature Operating: 0 °C to 40 °C; Non-operating: -40 °C to 70 °C
Humidity Operating: 5% to 80% RH (non-condensing), 50% RH above 30 °C
Non-operating: 5% to 95% RH (non-condensing), 75% RH above 30 °C and 45% RH above 40 °C
ESD Tolerance 2 kV (typical), 100 pF, 300 Ω HBM
Dimensions
Dx10-PT/Dx20-PT Positioner
Tip and Dx00A-AT Browser
0 to 3.5 mm (0 to 0.14”), 305 μm (0.012”) diameter
0.55 mm (0.022”) Z-axis compliance 0 to 3.0 mm (0 to 0.12”), 75 μm diameter
2 mm Z-axis compliance
Dx10-SI/Dx20-SI
Dx10-QC/Dx20-QC Tips 0 to 11 mm (0 to 0.43”) tip spread at circuit connection NA
Cable Length 1.3 m (4 ft. 3 in) for both WL-PLINK and WL-PBUS2
* All Bandwidth and Rise Time measurements are made with an oscilloscope bandwidth greater or equal to the probe bandwidth
† Through entire frequency range
© 2018 by Teledyne LeCroy, Inc. All rights reserved. Specications, prices, availability, and delivery subject to change
without notice. Product or brand names are trademarks or requested trademarks of their respective holders.
wavelinklowspeed-ds-07may18
ORDERING INFORMATION
1-800-5-LeCroy
teledynelecroy.com
Local sales oces are located throughout the world.
Visit our website to nd the most convenient location.
Product Description Product Code
Complete Differential Probes
4 GHz ProBus2 Differential Probe with Dx10-SI Solder-In Tip (Qty. 1),
Dx10-SP Square Pin (Qty. 1), and Dx10-QC Quick Connect (Qty. 1)
D410-A-PB2
4 GHz ProLink Differential Probe with Dx10-SI Solder-In Tip (Qty. 1),
Dx10-SP Square Pin (Qty. 1), and Dx10-QC Quick Connect (Qty. 1)
D410-A-PL
4 GHz ProBus2 Differential Probe with Dx20-SI Solder-In Tip (Qty. 1),
Dx20-SP Square Pin (Qty. 1), and Dx20-QC Quick Connect (Qty. 1)
D420-A-PB2
4 GHz ProLink Differential Probe with Dx20-SI Solder-In Tip (Qty. 1),
Dx20-SP Square Pin (Qty. 1), and Dx20-QC Quick Connect (Qty. 1)
D420-A-PL
6 GHz ProBus2 Differential Probe with Dx10-SI Solder-In Tip (Qty. 1),
Dx10-SP Square Pin (Qty. 1), and Dx10-QC Quick Connect (Qty. 1)
D610-A-PB2
6 GHz ProLink Differential Probe with Dx10-SI Solder-In Tip (Qty. 1),
Dx10-SP Square Pin (Qty. 1), and Dx10-QC Quick Connect (Qty. 1)
D610-A-PL
6 GHz ProBus2 Differential Probe with Dx20-SI Solder-In Tip (Qty. 1),
Dx20-SP Square Pin (Qty. 1), and Dx20-QC Quick Connect (Qty. 1)
D620-A-PB2
6 GHz ProLink Differential Probe with Dx20-SI Solder-In Tip (Qty. 1),
Dx20-SP Square Pin (Qty. 1), and Dx20-QC Quick Connect (Qty. 1)
D620-A-PL
4 GHz ProBus2 Differential Probe with Adjustable Tip D400A-AT-PB2
6 GHz ProBus2 Differential Probe with Adjustable Tip D600A-AT-PB2
6 GHz ProLink Differential Probe with Adjustable Tip D600A-AT-PL
Positioner Tip (Browser) Kits
WaveLink Dx10-PT Adjustable Positioner Tip Kit.
For use with Dx10 ampliers.
Dx10-PT-KIT
WaveLink Dx20-PT Adjustable Positioner Tip Kit.
For use with Dx20 ampliers.
Dx20-PT-KIT
QuickLink Solder-In Tip Set
QuickLink Solder-In starter pack for use with Dx10 amplier.
Includes one QuickLink adapter and three QL-SI tips.
Dx10-QL-3SI
QuickLink Solder-In starter pack for use with Dx20 amplier.
Includes one QuickLink adapter and three QL-SI tips.
Dx20-QL-3SI
Hi-Temp Leads
WaveLink Temperature Extension Cables for Dx10.
Includes set of Matched 30" High Temperature Cables (Qty. 1)
and solder-in lead set (Qty. 1)
Dx10-HiTemp
WaveLink Temperature Extension Cables for Dx20.
Includes set of Matched 30" High Temperature Cables (Qty. 1)
and solder-in lead set (Qty. 1)
Dx20-HiTemp
Product Description Product Code
Accessories
Cascade Microtech EZ-Probe Positioner EZ PROBE
Probe Deskew and Calibration Test Fixture TF-DSQ
Calibration Options
NIST Calibration for D410-A. Includes test data. D410-A-CCNIST
NIST Calibration for D420-A. Includes test data. D420-A-CCNIST
NIST Calibration for D610-A. Includes test data. D610-A-CCNIST
NIST Calibration for D620-A. Includes test data. D620-A-CCNIST
NIST Calibration for D400A-AT. Includes test data. D400A-AT-CCNIST
NIST Calibration for D600A-AT. Includes test data. D600A-AT-CCNIST
Replacement Parts
Single replacement QuickLink Solder-In Tip QL-SI-1Pack
9-pack of replacement QuickLink Solder-In Tip QL-SI-9Pack
Replacement Dx10-SI 4 & 6 GHz Solder-In Lead with
Qty. 5 Spare Resistors.
Dx10-SI
Replacement Dx20-SI 4 & 6 GHz Solder-In Lead with
Qty. 5 Spare Resistors.
Dx20-SI
Replacement Dx10-QC 4 & 6 GHz Quick Connect Lead Dx10-QC
Replacement Dx20-QC 4 & 6 GHz Quick Connect Lead Dx20-QC
Replacement Dx10-SP 4 & 6 GHz Square Pin Lead Dx10-SP
Replacement Dx20-SP 4 & 6 GHz Square Pin Lead Dx20-SP
Replacement SI Resistor Kit for Dx10/Dx20 - Kit of 20 PKxx0-SI
Replacement QC Resistor Kit for Dx10/Dx20 - 2 kits of 20 PKxx0-QC
Qty. 4 Replacement Pogo Pin Tips and Qty. 2
Replacement Sockets for Dx10-PT and
Dx20-PT Adjustable Positioner Tips.
Dxx0-PT-TIPS
Replacement Probe Tip Holder Kit PK600ST-3
Replacement Platform/Cable Assembly Mounting Kit PK600ST-4
Quantity 1 Package of Black Adhesive Pads (10/pkg) and
Quantity 1 Package of White Adhesive Pads (10/pkg)
Dxx0-PT-TAPE
Quantity 1 Package of Adhesive Probe Connection Guides
(200 individual guides/package)
Dxx0-PT-GUIDES
Customer Service
Teledyne LeCroy oscilloscopes and probes are designed, built, and tested to
ensure high reliability. In the unlikely event you experience difculties, our digital
oscilloscopes are fully warranted for three years and our probes are warranted for
one year.
This warranty includes:
• No charge for return shipping
• Long-term 7-year support
• Upgrade to latest software at no charge
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Teledyne LeCroy:
DX20-SI DX20-SP DX10-SP DX10-QC DX20-PT DX20-QC DX10-SI PKXX0-SI